PIC16(L)F1933 PIC16(L)F1933 Silicon Errata and Data Sheet Clarification The PIC16(L)F1933 devices that you have received conform functionally to the current Device Data Sheet (DS41575A), except for the anomalies described in this document. For example, to identify the silicon revision level using MPLAB IDE in conjunction with MPLAB ICD 3 or PICkitTM 3: 1. The silicon issues discussed in the following pages are for silicon revisions with the Device and Revision IDs listed in Table 1. The silicon issues are summarized in Table 2. 2. The errata described in this document will be addressed in future revisions of the PIC16(L)F1933 silicon. Note: 3. This document summarizes all silicon errata issues from all revisions of silicon, previous as well as current. Only the issues indicated in the last column of Table 2 apply to the current silicon revision (A7). 4. Note: Data Sheet clarifications and corrections start on page 10, following the discussion of silicon issues. The silicon revision level can be identified using the current version of MPLAB(R) IDE and Microchip's programmers, debuggers, and emulation tools, which are available at the Microchip corporate web site (www.microchip.com). TABLE 1: Using the appropriate interface, connect the device to the MPLAB ICD 3 programmer/ debugger or PICkitTM 3. From the main menu in MPLAB IDE, select Configure>Select Device, and then select the target part number in the dialog box. Select the MPLAB hardware tool (Debugger>Select Tool). Perform a "Connect" operation to the device (Debugger>Connect). Depending on the development tool used, the part number and Device Revision ID value appear in the Output window. If you are unable to extract the silicon revision level, please contact your local Microchip sales office for assistance. The DEVREV values for the various PIC16(L)F1933 silicon revisions are shown in Table 1. SILICON DEVREV VALUES Part Number Device ID(1) Revision ID for Silicon Revision(2) A1 A2 A3 A4 A6 A7 PIC16F1933 10 0011 001x xxxx 1 2 3 4 6 7 PIC16LF1933 10 0100 001x xxxx 1 2 3 4 6 7 Note 1: 2: The Device ID is located in the last configuration memory space. Refer to the "PIC16F193X/LF193X and PIC16F194X/LF194X Memory Programming Specification" (DS41397) for detailed information on Device and Revision IDs for your specific device. 2009-2011 Microchip Technology Inc. DS80490H-page 1 PIC16(L)F1933 TABLE 2: PIC16F1933 SILICON ISSUE SUMMARY Module Feature Data EE Memory Memory Endurance Affected Revisions(1) Item Number Issue Summary 1.1 Erase/Write endurance limited. A1 A2 A3 A4 A6 A7 X Data EE Memory Writes 1.2 Min. VDD for writes. X Program Flash Memory (PFM) Endurance 2.1 Erase/Write endurance limited. X Program Flash Memory (PFM) Writes 2.2 Min. VDD for writes. Timer1 Timer0 Gate Source 3.1 Timer1 Timer1 Gate Toggle mode X X X X X X X X X X X Toggle mode works improperly. X X 3.2 T1 Gate flip-flop does not clear. X X X Electrical Specifi- RA6/OSC2 Pin Input cations Leakage Current 4.1 Input leakage current ranges. X X X EUSART 16-Bit High-Speed Asynchronous mode 5.1 Works improperly at maximum rate. X X X X X X Resets Power-on Reset (POR) 6.1 Reset under low power conditions. X X ADC ADC Conversion 7.1 ADC conversion may not complete. X X X Enhanced Capture Compare PWM (ECCP) Enhanced PWM 8.1 PWM 0% duty cycle direction change. X X X X Enhanced Capture Compare PWM (ECCP) Enhanced PWM 8.2 PWM 0% duty cycle port steering. X X X X In-Circuit Serial ProgrammingTM (ICSPTM) Low-Voltage Programming 9.1 Bulk Erase not available with LVP. X X X LDO Minimum VDD above 85C 10.1 Minimum operating VDD for the PIC16F1933 devices at TA > 85C. X X X X X Note 1: X Only those issues indicated in the last column apply to the current silicon revision. DS80490H-page 2 2009-2011 Microchip Technology Inc. PIC16(L)F1933 TABLE 3: PIC16LF1933 SILICON ISSUE SUMMARY Module Feature Item Number Issue Summary Affected Revisions(1) A1 Data EE Memory Memory Endurance 1.1 Erase/Write endurance limited. X Data EE Memory Writes 1.2 Min. VDD for writes. X Program Flash Memory (PFM) Endurance 2.1 Erase/Write endurance limited. X Program Flash Memory (PFM) Writes 2.2 Min. VDD for writes. Timer1 Timer0 Gate Source 3.1 Timer1 Timer1 Gate Toggle mode Electrical Specifications A2 A3 A4 A6 A7 X X X X X X X X X X X Toggle mode works improperly. X X 3.2 T1 Gate flip-flop does not clear. X X X RA6/OSC2 Pin Input Leakage Current 4.1 Input leakage current ranges. X X X EUSART 16-Bit High-Speed Asynchronous mode 5.1 Works improperly at maximum rate. X X X X X X ADC ADC Conversion 7.1 ADC conversion may not complete. X X X Enhanced Capture Compare PWM (ECCP) Enhanced PWM 8.1 PWM 0% duty cycle direction change. X X X X Enhanced Capture Compare PWM (ECCP) Enhanced PWM 8.2 PWM 0% duty cycle port steering. X X X X In-Circuit Serial Pro- Low-Voltage grammingTM Programming (ICSPTM) 9.1 Bulk Erase not available with LVP. X X X BOR 11.1 Device resets on wake-up from Sleep (PIC16LF1933 device only). X X X Note 1: Wake-up from Sleep X Only those issues indicated in the last column apply to the current silicon revision. 2009-2011 Microchip Technology Inc. DS80490H-page 3 PIC16(L)F1933 Silicon Errata Issues Note: 2.2 Program Flash Memory writes at Min. VDD This document summarizes all silicon errata issues from all revisions of silicon, previous as well as current. Only the issues indicated by the shaded column in the following tables apply to the current silicon revision (A7). 1. Module: Data EE Memory 1.1 Data EE Memory Endurance The typical write/erase endurance of the Data EE Memory is limited to 10k cycles. Work around Use error correction method that stores data in multiple locations. Affected Silicon Revisions A1 A2 A3 A4 A6 A7 X 1.2 Data EE Write at Min. VDD The minimum voltage required for a Data EE write operation is 2.0 volts. None. Affected Silicon Revisions A1 A2 A3 A4 A6 A7 X X X X X X 2. Module: Program Flash Memory (PFM) 2.1 Program Flash Memory Endurance The typical write/erase endurance of the PFM is limited to 1k cycles when VDD is above 3.0 volts. Work around Use an error correction method that stores data in multiple locations. Affected Silicon Revisions A2 X Work around None. Affected Silicon Revisions A1 A2 A3 A4 A6 A7 X X X X X X 3. Module: Timer1 3.1 Timer1 Gate Toggle mode with Timer0 as Gate Source Timer1 Gate Toggle mode provides unexpected results when Timer0 overflow is selected as the Timer1 gate source. We do not recommend using Timer0 overflow as the Timer1 gate source while in Timer1 Gate Toggle mode or when Toggle mode is used in conjunction with Timer1 Gate Single-Pulse mode. Work around None. Affected Silicon Revisions Work around A1 The minimum voltage required for a PFM write operation is 2.0V. A3 A4 A6 A7 A1 A2 X X A3 A4 A6 A7 3.2 Timer1 Gate Toggle mode When Timer1 Gate Toggle mode is enabled, it is possible to measure the full-cycle length of a Timer1 gate signal. To perform this function, the Timer1 gate source is routed through a flip-flop that changes state on every incrementing edge of the gate signal. Timer1 Gate Toggle mode is enabled by setting the T1GTM bit of the T1GCON register. When working properly, clearing either the T1GTM bit or the TMR1ON bit would also clear the output value of this flip-flop, and hold it clear. This is done in order to control which edge is being measured. The issue that exists is that clearing the TMR1ON bit does not clear the output value of the flip-flop and hold it clear. Work around Clear the T1GTM bit in the T1GCON register to clear and hold clear the output value of the flipflop. Affected Silicon Revisions DS80490H-page 4 A1 A2 A3 X X X A4 A6 A7 2009-2011 Microchip Technology Inc. PIC16(L)F1933 4. Module: Electrical Specifications 4.1 RA6/OSC2 Pin Leakage Range The Input Leakage Currents on the RA6/OSC2 pin are as follows: Characteristic Min. Typ Max. Units Conditions Operating Temperature RA6/OSC2 Input Leakage Current -- 5 1500 nA Vss VPIN VDD, Pin at High-Impedance -40C TA +85C RA6/OSC2 Input Leakage Current -- 5 5000 nA Vss VPIN VDD, Pin at High-Impedance -40C TA +125C Work around None. Affected Silicon Revisions A1 A2 A3 X X X A4 A6 A7 5. Module: EUSART 5.1 16-Bit High-Speed Asynchronous Mode The EUSART provides unexpected operation when the 16-Bit High-Speed Asynchronous mode is selected and the Baud Rate Generator Data Register values are loaded with zero (0). We do not recommend using this configuration for EUSART communication. The configuration is shown below in the following table: Configuration Bits BRG Data Registers SYNC BRG16 BRGH SPBRGH Value SPBRGL Value 0 1 1 00000000 00000000 Work around Ensure that the SPBRGH or the SPBRGL register is loaded with a non-zero value. Affected Silicon Revisions A1 A2 A3 A4 A6 A7 X X X X X X 2009-2011 Microchip Technology Inc. DS80490H-page 5 PIC16(L)F1933 6. Module: Resets 7. Module: ADC 6.1 Reset under Low-Power Conditions 7.1 Analog-to-Digital Conversion This issue pertains to the PIC16F1933 product only. The PIC16LF1933 product is not affected by this issue in any way. When employing any one of the low-power oscillators, (ECL mode, LP Mode, LFINTOSC, or Timer1 Oscillator) while, at the same time, the source voltage supplied to the VDD pin drops below 2.7 volts, the device will experience a Power-on Reset (POR). Also, when the source voltage supplied to the VDD pin is below 2.7 volts and a SLEEP instruction is executed, the device will experience a Power-on Reset (POR) upon entering Sleep mode, regardless of the type of clock source being used or which power-managed mode is being employed. Work around There are three separate work-arounds available to avoid this Reset condition. Employing any one of these work-arounds will avoid this Reset condition. * Enabling the Brown-out Reset (BOR) circuitry. * Enabling the Fixed Voltage Reference (FVR) module. * Maintaining a source voltage (VDD) to the device above 2.7 volts. The `Affected Silicon Revisions' below refers only to PIC16F1933. Affected Silicon Revisions A1 A2 X X DS80490H-page 6 A3 A4 A6 A7 An ADC conversion may not complete under these conditions: 1. 2. When FOSC is greater than 8 MHz and it is the clock source used for the ADC converter. The ADC is operating from its dedicated internal FRC oscillator and the device is not in Sleep mode (any FOSC frequency). When this occurs, the ADC Interrupt Flag (ADIF) does not get set, the GO/DONE bit does not get cleared, and the conversion result does not get loaded into the ADRESH and ADRESL result registers. Work around Method 1: Select the system clock, FOSC, as the ADC clock source and reduce the FOSC frequency to 8 MHz or less when performing ADC conversions. Method 2: Select the dedicated FRC oscillator as the ADC conversion clock source and perform all conversions with the device in Sleep. Method 3: This method is provided if the application cannot use Sleep mode and requires continuous operation at frequencies above 8 MHz. This method requires early termination of an ADC conversion. Provide a fixed time delay in software to stop the A-toD conversion manually, after all 10 bits are converted, but before the conversion would complete automatically. The conversion is stopped by clearing the GO/ DONE bit in software. The GO/ DONE bit must be cleared during the last 1/2 TAD cycle, before the conversion would have completed automatically. Refer to Figure 1 for details. 2009-2011 Microchip Technology Inc. PIC16(L)F1933 FIGURE 1: INSTRUCTION CYCLE DELAY CALCULATION EXAMPLE FOSC = 32 MHz TCY = 4/32 MHz = 125 nsec TAD = 1 sec, ADCS = FOSC/32 88 TCY 84 TCY 8 TCY } Stop the A/D conversion between 10.5 and 11 TAD cycles. 4 TCY See the Analog-to-Digital Conversion Timing diagram in the Analog-to-Digital Converter chapter of the device data sheet. 11 TAD 1 TAD See the ADC Clock Period (TAD) vs. Device Operating Frequencies table, in the Analog-to-Digital Converter section of the device data sheet. In Figure 1, 88 instruction cycles (TCY) will be required to complete the full conversion. Each TAD cycle consists of 8 TCY periods. A fixed delay is provided to stop the A/D conversion after 86 instruction cycles and terminate the conversion at the correct time as shown in the figure above. Note: The exact delay time will depend on the TAD divisor (ADCS) selection. The TCY counts shown in the timing diagram above apply to this example only. Refer to Table 4 for the required delay counts for other configurations. EXAMPLE 1: TABLE 4: INSTRUCTION CYCLE DELAY COUNTS BY TAD SELECTION TAD Instruction Cycle Delay Counts FOSC/64 172 FOSC/32 86 FOSC/16 43 Affected Silicon Revisions A1 A2 A3 X X X A4 A6 A7 CODE EXAMPLE OF INSTRUCTION CYCLE DELAY BSF ADCON0, ADGO BCF ADCON0, ADGO MOVF ADRESH, W ; Start ADC conversion ; Provide 86 instruction cycle delay here ; Terminate the conversion manually ; Read conversion result For other combinations of FOSC, TAD values and Instruction cycle delay counts, refer to Table 4. 2009-2011 Microchip Technology Inc. DS80490H-page 7 PIC16(L)F1933 8. Module: Enhanced Capture Compare PWM (ECCP) 9. Module: In-Circuit Serial ProgrammingTM (ICSPTM) 8.1 Enhanced PWM 9.1 Bulk Erase Feature not available with LowVoltage Programming mode When the PWM is configured for Full-Bridge mode and the duty cycle is set to 0%, writing the PxM<1:0> bits to change the direction has no effect on PxA and PxC outputs. On the A4 revision products only, ECCP1 no longer exhibits this problem. A bulk erase of the program Flash memory or data memory cannot be executed in Low-Voltage Programming mode. Work around Method 1: If ICSP Low-Voltage Programming mode is required, use row erases to erase the program memory, as described in the Program/Verify mode section of the Programming Specification. Data memory must be over-written with the desired values. Work around Increase the duty cycle to a value greater than 0% before changing directions. Affected Silicon Revisions A1 A2 A3 A4 X X X X A6 A7 Method 2: Use ICSP High-Voltage Programming mode if a bulk erase is required. 8.2 Enhanced PWM In PWM mode, when the duty cycle is set to 0% and the STRxSYNC bit is set, writing the STRxA, STRxB, STRxC and the STRxD bits to enable/ disable steering to port pins has no effect on the outputs. Note: Work around Increase the duty cycle to a value greater than 0% before enabling/disabling steering to port pins. Affected Silicon Revisions A1 A2 A3 A4 X X X X A6 Only the bulk erase feature will erase program or data memory if code or data protection is enabled. Method 2 must be used if code or data protection is enabled. Affected Silicon Revisions A1 A2 A3 X X X A4 A6 A7 A7 10. Module: LDO 10.1 Minimum VDD above 85C The minimum voltage required for the PIC16F1933 devices is 3.5 volts for temperatures above 85C. Note: This issue only applies to the PIC16F1933 devices operating in the Extended temperature range. The PIC16LF1933 devices are not affected. Work around None. Affected Silicon Revisions DS80490H-page 8 A1 A2 A3 A4 A6 A7 X X X X X X 2009-2011 Microchip Technology Inc. PIC16(L)F1933 11. Module: BOR Note: 11.1 BOR Reset This issue affects only the PIC16LF1933 device. The device may undergo a BOR Reset when waking-up from Sleep and BOR is re-enabled. A BOR Reset may also occur the moment the software BOR is enabled. Under certain voltage and temperature conditions and when either SBODEN or BOR_NSLEEP is selected, the devices may occasionally reset when waking-up from Sleep or BOR is enabled. When using the software BOR follow the steps in Methods 3 or 4 above when enabling BOR for the first time during program execution. Affected Silicon Revisions A1 A2 A3 A4 X X X X A6 A7 Work around Method 1: In applications where BOR use is not critical, turn off the BOR in the Configuration Word. Method 2: Set the FVREN bit of the FVRCON register. Maintain this bit on at all times. Method 3: When BOR module is needed only during run-time, use the software-enabled BOR by setting the SBODEN option on the Configuration Word. BOR should be turned off by software before Sleep, then follow the below sequence for turning BOR on after wake-up: a. Wake-up event occurs; b. Turn on FVR (FVREN bit of the FVRCON register); c. Wait until FVRRDY bit is set; d. Wait 15 s after the FVR Ready bit is set; e. Manually turn on the BOR. Method 4: Use the software-enabled BOR as described in Method 3, but use the following sequence: a. Switch to internal 32 kHz oscillator immediately before Sleep; b. Upon wake-up, turn on FVR (FVREN bit of the FVRCON register); c. Manually turn on the BOR; d. Switch the clock back to the preferred clock source. 2009-2011 Microchip Technology Inc. DS80490H-page 9 PIC16(L)F1933 Data Sheet Clarifications The following typographic corrections and clarifications are to be noted for the latest version of the device data sheet (DS41575A). None. DS80490H-page 10 2009-2011 Microchip Technology Inc. PIC16(L)F1933 APPENDIX A: DOCUMENT REVISION HISTORY Rev A Document (10/2009) Initial release of this document. Rev B Document (02/2010) Added PIC16F1933 device to this errata; Added Rev. A2 for PIC16F/LF1933 (Table 2); Added Table 3. Added Module 6 to Silicon Errata Issues section. Data Sheet Clarifications: Added Modules 1 and 2. Rev C Document (05/2010) Added Revision A3 to Tables 1, 2 and 3; Added Modules 7, 8. Data Sheet Clarifications: Added Modules 3 and 4. Rev D Document (07/2010) Added Module 3.2; Revised Module 7.1; Added Module 9.1; Other minor corrections. Rev E Document (08/2010) Updated errata to the new format; Revised Table below Module 4.1, changing the Max. values; Updated Table 4; Revised Note above Example 1; Other minor corrections. Rev F Document (10/2010) Added Silicon Revision A4; Added Module 10: LDO, to Table 2. Rev G Document (06/2011) Added Module 11.1, BOR; Remove Data Sheet Clarifications; Add Rev. A6 Silicon. Rev H Document (11/2011) Added Rev. A7 Silicon. 2009-2011 Microchip Technology Inc. DS80490H-page 11 PIC16(L)F1933 NOTES: DS80490H-page 12 2009-2011 Microchip Technology Inc. Note the following details of the code protection feature on Microchip devices: * Microchip products meet the specification contained in their particular Microchip Data Sheet. * Microchip believes that its family of products is one of the most secure families of its kind on the market today, when used in the intended manner and under normal conditions. * There are dishonest and possibly illegal methods used to breach the code protection feature. All of these methods, to our knowledge, require using the Microchip products in a manner outside the operating specifications contained in Microchip's Data Sheets. Most likely, the person doing so is engaged in theft of intellectual property. * Microchip is willing to work with the customer who is concerned about the integrity of their code. * Neither Microchip nor any other semiconductor manufacturer can guarantee the security of their code. Code protection does not mean that we are guaranteeing the product as "unbreakable." Code protection is constantly evolving. We at Microchip are committed to continuously improving the code protection features of our products. Attempts to break Microchip's code protection feature may be a violation of the Digital Millennium Copyright Act. If such acts allow unauthorized access to your software or other copyrighted work, you may have a right to sue for relief under that Act. Information contained in this publication regarding device applications and the like is provided only for your convenience and may be superseded by updates. It is your responsibility to ensure that your application meets with your specifications. MICROCHIP MAKES NO REPRESENTATIONS OR WARRANTIES OF ANY KIND WHETHER EXPRESS OR IMPLIED, WRITTEN OR ORAL, STATUTORY OR OTHERWISE, RELATED TO THE INFORMATION, INCLUDING BUT NOT LIMITED TO ITS CONDITION, QUALITY, PERFORMANCE, MERCHANTABILITY OR FITNESS FOR PURPOSE. Microchip disclaims all liability arising from this information and its use. Use of Microchip devices in life support and/or safety applications is entirely at the buyer's risk, and the buyer agrees to defend, indemnify and hold harmless Microchip from any and all damages, claims, suits, or expenses resulting from such use. No licenses are conveyed, implicitly or otherwise, under any Microchip intellectual property rights. Trademarks The Microchip name and logo, the Microchip logo, dsPIC, KEELOQ, KEELOQ logo, MPLAB, PIC, PICmicro, PICSTART, PIC32 logo, rfPIC and UNI/O are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FilterLab, Hampshire, HI-TECH C, Linear Active Thermistor, MXDEV, MXLAB, SEEVAL and The Embedded Control Solutions Company are registered trademarks of Microchip Technology Incorporated in the U.S.A. Analog-for-the-Digital Age, Application Maestro, chipKIT, chipKIT logo, CodeGuard, dsPICDEM, dsPICDEM.net, dsPICworks, dsSPEAK, ECAN, ECONOMONITOR, FanSense, HI-TIDE, In-Circuit Serial Programming, ICSP, Mindi, MiWi, MPASM, MPLAB Certified logo, MPLIB, MPLINK, mTouch, Omniscient Code Generation, PICC, PICC-18, PICDEM, PICDEM.net, PICkit, PICtail, REAL ICE, rfLAB, Select Mode, Total Endurance, TSHARC, UniWinDriver, WiperLock and ZENA are trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. SQTP is a service mark of Microchip Technology Incorporated in the U.S.A. All other trademarks mentioned herein are property of their respective companies. (c) 2009-2011, Microchip Technology Incorporated, Printed in the U.S.A., All Rights Reserved. Printed on recycled paper. ISBN: 978-1-61341-773-7 Microchip received ISO/TS-16949:2009 certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona; Gresham, Oregon and design centers in California and India. The Company's quality system processes and procedures are for its PIC(R) MCUs and dsPIC(R) DSCs, KEELOQ(R) code hopping devices, Serial EEPROMs, microperipherals, nonvolatile memory and analog products. In addition, Microchip's quality system for the design and manufacture of development systems is ISO 9001:2000 certified. 2009-2011 Microchip Technology Inc. DS80490H-page 13 Worldwide Sales and Service AMERICAS ASIA/PACIFIC ASIA/PACIFIC EUROPE Corporate Office 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-792-7200 Fax: 480-792-7277 Technical Support: http://www.microchip.com/ support Web Address: www.microchip.com Asia Pacific Office Suites 3707-14, 37th Floor Tower 6, The Gateway Harbour City, Kowloon Hong Kong Tel: 852-2401-1200 Fax: 852-2401-3431 India - Bangalore Tel: 91-80-3090-4444 Fax: 91-80-3090-4123 India - New Delhi Tel: 91-11-4160-8631 Fax: 91-11-4160-8632 Austria - Wels Tel: 43-7242-2244-39 Fax: 43-7242-2244-393 Denmark - Copenhagen Tel: 45-4450-2828 Fax: 45-4485-2829 India - Pune Tel: 91-20-2566-1512 Fax: 91-20-2566-1513 France - Paris Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79 Japan - Yokohama Tel: 81-45-471- 6166 Fax: 81-45-471-6122 Germany - Munich Tel: 49-89-627-144-0 Fax: 49-89-627-144-44 Atlanta Duluth, GA Tel: 678-957-9614 Fax: 678-957-1455 Boston Westborough, MA Tel: 774-760-0087 Fax: 774-760-0088 Chicago Itasca, IL Tel: 630-285-0071 Fax: 630-285-0075 Cleveland Independence, OH Tel: 216-447-0464 Fax: 216-447-0643 Dallas Addison, TX Tel: 972-818-7423 Fax: 972-818-2924 Detroit Farmington Hills, MI Tel: 248-538-2250 Fax: 248-538-2260 Indianapolis Noblesville, IN Tel: 317-773-8323 Fax: 317-773-5453 Los Angeles Mission Viejo, CA Tel: 949-462-9523 Fax: 949-462-9608 Santa Clara Santa Clara, CA Tel: 408-961-6444 Fax: 408-961-6445 Toronto Mississauga, Ontario, Canada Tel: 905-673-0699 Fax: 905-673-6509 Australia - Sydney Tel: 61-2-9868-6733 Fax: 61-2-9868-6755 China - Beijing Tel: 86-10-8569-7000 Fax: 86-10-8528-2104 China - Chengdu Tel: 86-28-8665-5511 Fax: 86-28-8665-7889 Netherlands - Drunen Tel: 31-416-690399 Fax: 31-416-690340 China - Chongqing Tel: 86-23-8980-9588 Fax: 86-23-8980-9500 Korea - Seoul Tel: 82-2-554-7200 Fax: 82-2-558-5932 or 82-2-558-5934 China - Hangzhou Tel: 86-571-2819-3187 Fax: 86-571-2819-3189 Malaysia - Kuala Lumpur Tel: 60-3-6201-9857 Fax: 60-3-6201-9859 China - Hong Kong SAR Tel: 852-2401-1200 Fax: 852-2401-3431 Malaysia - Penang Tel: 60-4-227-8870 Fax: 60-4-227-4068 China - Nanjing Tel: 86-25-8473-2460 Fax: 86-25-8473-2470 Philippines - Manila Tel: 63-2-634-9065 Fax: 63-2-634-9069 China - Qingdao Tel: 86-532-8502-7355 Fax: 86-532-8502-7205 Singapore Tel: 65-6334-8870 Fax: 65-6334-8850 China - Shanghai Tel: 86-21-5407-5533 Fax: 86-21-5407-5066 Taiwan - Hsin Chu Tel: 886-3-5778-366 Fax: 886-3-5770-955 China - Shenyang Tel: 86-24-2334-2829 Fax: 86-24-2334-2393 Taiwan - Kaohsiung Tel: 886-7-536-4818 Fax: 886-7-330-9305 China - Shenzhen Tel: 86-755-8203-2660 Fax: 86-755-8203-1760 Taiwan - Taipei Tel: 886-2-2500-6610 Fax: 886-2-2508-0102 China - Wuhan Tel: 86-27-5980-5300 Fax: 86-27-5980-5118 Thailand - Bangkok Tel: 66-2-694-1351 Fax: 66-2-694-1350 Spain - Madrid Tel: 34-91-708-08-90 Fax: 34-91-708-08-91 UK - Wokingham Tel: 44-118-921-5869 Fax: 44-118-921-5820 China - Xian Tel: 86-29-8833-7252 Fax: 86-29-8833-7256 China - Xiamen Tel: 86-592-2388138 Fax: 86-592-2388130 China - Zhuhai Tel: 86-756-3210040 Fax: 86-756-3210049 DS80490H-page 14 Italy - Milan Tel: 39-0331-742611 Fax: 39-0331-466781 Korea - Daegu Tel: 82-53-744-4301 Fax: 82-53-744-4302 08/02/11 2009-2011 Microchip Technology Inc.