APC-25-1050 - MEAN WELL ENTERPRISES

MAX. No. of PSUs on 16A

CIRCUIT BREAKER 9 units (circuit breaker of type B) / 15 units (circuit breaker of type C) at 230VAC

SPECIFICATION

MODEL APC-25-350 APC-25-700

DC VOLTAGE RANGE

RATED CURRENT

RATED POWER

OUTPUT

LINE REGULATION

LOAD REGULATION

SETUP, RISE TIME

VOLTAGE RANGE Note.4

FREQUENCY RANGE

EFFICIENCY(Typ.)

AC CURRENT

INPUT

INRUSH CURRENT(Typ.)

LEAKAGE CURRENT

WORKING TEMP.

WORKING HUMIDITY

STORAGE TEMP., HUMIDITY

TEMP. COEFFICIENT

VIBRATION

MTBF

DIMENSIONOTHERS

NOTE

PACKING

OVER VOLTAGE

25~70V 11~36V

350mA 700mA

24.5W 25.2W

300mVp-p 300mVp-p

±5.0%

±1.0%

±3.0%

1500ms, 30ms / 230VAC 1500ms, 30ms / 115VAC at full load

47 ~ 63Hz

83% 83%

0.4A/230VAC;0.8A/115VAC

0.25mA / 240VAC

20 ~ 90% RH non-condensing

-40 ~ +80 , 10 ~ 95% RH℃

±℃ ℃0.2%/ (0 ~ 50 )

10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.℃

2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.

3. Tolerance : includes set up tolerance, line regulation and load regulation.

4. Derating may be needed under low input voltage. Please check the static characteristic for more details.

5. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the

complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again.

6. The unit might not be suitable for lighting applications in EU countries. Please check with your local authorities for the possible use of the unit.

7. The ambient temperature derating of 3.5 /1000m with fanless models and of 5 /1000m with fan models for operating altitude higher than 2000m(6500ft).℃℃

8. For any application note and IP water proof function installation caution, please refer our user manual before using.

https://www.meanwell.com/Upload/PDF/LED_EN.pdf

25W Single Output Switching Power Supply

Constant current mode power supply

Universal AC input / Full range

Withstand 300VAC Surge input for 5 seconds

Protections:Short circuit / Over voltage

Fully isolated plastic case

Small and compact size

Cooling by free air convection

IP42 design

100% full load burn-in test

Suitable for LED related fixture or appliance

(such as LED Decoration or Advertisement devices)

Low cost / High reliability

2 years warranty

RIPPLE & NOISE (max.) Note.2

VOLTAGE TOLERANCE Note.3

ENVIRONMENT

SAFETY &

EMC

(Note 5)

PROTECTION

File Name: APC-25-SPEC 2018-09-29

SAFETY STANDARDS

WITHSTAND VOLTAGE

ISOLATION RESISTANCE

I/P-O/P:3KVAC

HOLD UP TIME (Typ.) 20ms/230VAC 12ms/115VAC at full load

76 ~ 94V 41 ~ 49V

84*57*29.5(L*W*H)

COLD START 45A(twidth=310 s measured at 50% Ipeak) at 230VACμ

UL8750 (except for APC-25-350), CSA-C22.2 No. 250.0-13 (only for APC-25-700&1050), BIS IS15885, EAC TP TC 004,

IP42 approved; design refer to EN60950-1

518.9K hrs min. MIL-HDBK-217F (25 )℃

■Features :

LPS (except for APC-25-350)

I/P-O/P:>100M Ohms / 500VDC / 25 / 70% RH℃

90 ~ 264VAC 127 ~ 370VDC

APC-25 series

CURRENT ACCURACY

±8.0%

EMC IMMUNITY

Compliance to EN55032,EN61000-3-2 Class A,EN61000-3-3, EAC TP TC 020

Compliance to EN55024,EN61000-4-2,3,4,5,6,8,11; light industry level(surge 2KV), criteria A, EAC TP TC 020

EMC EMISSION

APC-25-500

15~50V

500mA

25.2W

300mVp-p

83%

55 ~ 68V

APC-25-1050

9~24V

1050mA

25.2W

300mVp-p

83%

27 ~ 35V

-30 ~ 70 (Refer to "Derating Curve")℃

0.13Kg; 72pcs/10.4Kg/0.92CUFT

Protection type : Shut down o/p voltage, re-power on to recover

(only for APC-25-700&1050)

( only for APC-25-500)

IP42

IS 15885(Part 2/Sec13)

R-41027766

THOMAS SAMUEL