Revised August 2004 NC7SZ175 TinyLogic UHS D-Type Flip-Flop with Asynchronous Clear General Description Features The NC7SZ175 is a single positive edge-triggered D-type CMOS Flip-Flop with Asynchronous Clear from Fairchild's Ultra High Speed Series of TinyLogic in the space saving SC70 6-lead package. The device is fabricated with advanced CMOS technology to achieve ultra high speed with high output drive while maintaining low static power dissipation over a very broad VCC operating range. The device is specified to operate over the 1.65V to 5.5V VCC range. The inputs and output are high impedance when VCC is 0V. Inputs tolerate voltages up to 7V independent of VCC operating voltage. This single flip-flop will store the state of the D input that meets the setup and hold time requirements on the LOW-to-HIGH Clock (CP) transition. A LOW input to Clear sets the Q output to LOW level. The Clear input is independent of clock. Space saving SC70 6-lead package Ultra small MicroPak leadless package Ultra High Speed; tPD 2.6 ns Typ into 50 pF at 5V VCC High Output Drive; 24 mA at 3V VCC Broad VCC Operating Range; 1.65V to 5.5V Matches the performance of LCX when operated at 3.3V VCC Power down high impedance inputs/output Overvoltage tolerant inputs facilitate 5V to 3V translation Proprietary noise/EMI reduction circuitry implemented Ordering Code: Order Package Product Code Number Number Top Mark NC7SZ175P6X MAA06A Z75 6-Lead SC70, EIAJ SC88, 1.25mm Wide 3k Units on Tape and Reel NC7SZ175L6X MAC06A C4 6-Lead MicroPak, 1.0mm Wide Package Description Supplied As 5k Units on Tape and Reel TinyLogic is a registered trademark of Fairchild Semiconductor Corporation. MicroPak is a trademark of Fairchild Semiconductor Corporation. (c) 2004 Fairchild Semiconductor Corporation DS500158 www.fairchildsemi.com NC7SZ175 TinyLogic UHS D-Type Flip-Flop with Asynchronous Clear May 1998 NC7SZ175 Connection Diagrams Logic Symbol IEEE/IEC Pin Assignments for SC70 Function Table Inputs CP X H = HIGH Logic Level L = LOW Logic Level Output D C Q L H L H H H X H Qn X L L (Top View) Pin One Orientation Diagram Qn = No change in data X = Immaterial Pin Descriptions Pin Names D CP AAA represents Product Code Top Mark - see ordering code Note: Orientation of Top Mark determines Pin One location. Read the top product code mark left to right, Pin One is the lower left pin (see diagram). Description Data Input Pad Assignments for MicroPak Clock Pulse Input C Clear Input Q Flip-Flop Output (Top Thru View) www.fairchildsemi.com 2 Supply Voltage (VCC) -0.5V to +7.0V DC Input Voltage (VIN) -0.5V to +7.0V DC Output Voltage (VOUT) -0.5V to +7.0V Recommended Operating Conditions (Note 2) Power Supply DC Input Diode Current (IIK) VIN < 0V -50 mA DC Output Diode Current (IOK) VOUT < 0V -50 mA Operating (VCC ) 1.65V to 5.5V Data Retention 1.5V to 5.5V Input Voltage (VIN) 0V to 5.5V Output Voltage (VOUT) 0V to VCC Input Rise and Fall Time (tr, tf) DC Output (IOUT) Source/Sink Current 50 mA VCC = 1.8V, 2.5V 0.2V 0 to 20 ns/V DC VCC/GND Current (ICC/IGND) 50 mA VCC = 3.3V 0.3V 0 to 10 ns/V -65C to +150C VCC = 5.5V 0.5V Storage Temperature Range (TSTG) 150C Junction Temperature under Bias (TJ) 0 to 5 ns/V -40C to +85C Operating Temperature (TA) Thermal Resistance (JA) Junction Lead Temperature (TL) 260C (Soldering, 10 seconds) Power Dissipation (PD) @+85C 350 C/W Note 1: The "Absolute Maximum Ratings": are those values beyond which the safety of the device cannot be guaranteed. The device should not be operated at these limits. The parametric values defined in the Electrical Characteristics tables are not guaranteed at the absolute maximum ratings. The "Recommended Operating Conditions" table will define the conditions for actual device operation. 180 mW Note 2: Unused inputs must be held HIGH or LOW. They may not float. DC Electrical Characteristics Symbol Parameter (V) VIH HIGH Level Control Input Voltage VIL LOW Level Control Input Voltage VOH VOL TA = +25C VCC Min Typ TA = -40C to +85C Max 1.65 to 1.95 0.75 VCC 2.3 to 5.5 Min 0.75 VCC 0.7 VCC 1.65 to 1.95 0.25 VCC 0.25 VCC 2.3 to 5.5 0.3 VCC 0.3 VCC HIGH Level Control 1.65 1.55 1.65 1.8 1.7 1.8 1.7 2.3 2.2 2.3 2.2 3.0 2.9 3.0 2.9 IOH = -100 A 4.4 4.5 4.4 1.24 1.52 1.29 2.3 1.9 2.15 1.9 IOH = -8 mA 3.0 2.4 2.8 2.4 IOH = -16 mA 3.0 2.3 2.68 2.3 IOH = -24 mA 4.5 3.8 4.2 3.8 V 0.1 Output Voltage 1.8 0.0 0.1 0.1 2.3 0.0 0.1 0.1 3.0 0.0 0.1 0.1 Power Off Leakage Current ICC Quiescent Supply Current or VIL IOH = -4 mA IOH = -32 mA 0.0 IOFF VIN = VIH 4.5 1.65 1.65 Input Leakage Current V 1.55 LOW Level Control IIN Conditions V 0.7 VCC Output Voltage Unit Max 0.1 IOL = 100 A VIN = VIL 4.5 0.0 0.1 0.1 1.65 0.08 0.24 0.24 2.3 0.10 0.3 0.3 IOL = 8 mA 3.0 0.15 0.4 0.4 IOL = 16 mA 3.0 0.22 0.55 0.55 IOL = 24 mA 4.5 0.22 0.55 0.55 0 to 5.5 0.1 1.0 A 0 VIN 5.5V 0.0 1.0 10 A VIN or VOUT = 5.5V 1.65 to 5.5 1.0 10.0 A VIN = 5.5V, GND 3 V or VIH IOL = 4 mA IOL = 32 mA www.fairchildsemi.com NC7SZ175 Absolute Maximum Ratings(Note 1) NC7SZ175 AC Electrical Characteristics Symbol fMAX TA = +25C VCC Parameter (V) Min Typ TA = -40C to +85C Max Min Maximum Clock 1.65 Frequency 1.8 100 2.5 0.2 125 3.3 0.3 150 Max Units Conditions Figure Number 100 5.0 0.5 MHz CL = 50 pF RL = 500 Figures 1, 4 175 tPLH Propagation Delay 1.65 2.5 9.8 15.0 2.5 16.5 tPHL CP to Q 1.8 2.5 6.5 10.0 2.5 11.0 2.5 0.2 2.0 3.8 6.5 2.0 7.0 3.3 0.3 1.5 2.8 4.5 1.4 5.0 5.0 0.5 1.0 2.2 3.5 1.0 3.8 3.3 0.3 2.0 3.4 5.5 1.6 6.2 CL = 50 pF 5.0 0.5 1.5 2.6 4.0 1.4 4.7 RL = 500 Figures 1, 3 Propagation Delay 1.65 2.5 9.8 13.5 2.5 15.0 C to Q 1.8 2.5 6.5 9.0 2.5 10.0 2.5 0.2 2.0 3.8 6.0 2.0 6.4 CL = 15 pF 3.3 0.3 Figures 1, 3 1.5 2.8 4.3 1.2 4.6 5.0 0.5 1.5 2.2 3.2 1.0 3.5 3.3 0.3 1.5 3.4 5.3 1.5 5.8 CL = 50 pF 5.0 0.5 1.0 2.7 4.0 1.2 4.5 RL = 500 tPHL tS tH Setup Time 2.5 0.2 2.5 CP to D 3.3 0.3 2.0 5.0 0.5 1.5 Hold Time, 2.5 0.2 1.5 CP to D 3.3 0.3 1.5 5.0 0.5 1.5 2.5 0.2 3.0 3.3 0.3 2.8 5.0 0.5 2.5 2.5 0.2 3.0 3.3 0.3 2.8 5.0 0.5 2.5 Recovery Time, 2.5 0.2 1.0 C to CP 3.3 0.3 1.0 5.0 0.5 1.0 Pulse Width, CP tW Pulse Width, C trec CL = 15 pF ns ns RL = 1 M RL = 1 M CL = 50 pF ns RL = 500 ns RL = 500 CL = 50 pF CL = 50 pF ns RL = 500 Figures 1, 3 Figures 1, 3 Figures 1, 4 Figures 1, 4 Figures 1, 4 Clock HIGH or LOW ns CL = 50 pF RL = 500 CL = 50 pF ns RL = 500 Figures 1, 4 Figures 1, 4 Capacitance (Note 3) Symbol Parameter Typ Max Units Conditions 3 pF VCC = Open, VIN = 0V or VCC Output Capacitance 4 pF VCC = 3.3V, VIN = 0V or VCC Power Dissipation Capacitance 10 (Note 4) 12 CIN Input Capacitance COUT CPD pF VCC = 3.3V VCC = 5.0V Note 3: TA = +25C, f = 1MHz. Note 4: C PD is defined as the value of the internal equivalent capacitance which is derived from dynamic operating current consumption (ICCD ) at no output loading and operating at 50% duty cycle. (See Figure 2) CPD is related to ICCD dynamic operating current by the expression: ICCD = (CPD)(VCC)(fIN) + (ICCstatic). www.fairchildsemi.com 4 NC7SZ175 AC Loading and Waveforms CL includes load and stray capacitance CP Input = AC Waveform; tr = tf = 1.8 ns; Input PRR = 1.0 MHz, tw = 500 ns CP Input PRR = 10 MHz; Duty Cycle = 50% D Input PRR = 5MHz; Duty Cycle = 50% FIGURE 1. AC Test Circuit FIGURE 2. ICCD Test Circuit FIGURE 3. AC Waveforms FIGURE 4. AC Waveforms 5 www.fairchildsemi.com NC7SZ175 Tape and Reel Specification TAPE FORMAT for SC70 Package Designator P6X Tape Number Cavity Section Cavities Status Cover Tape Status Leader (Start End) 125 (typ) Empty Sealed Carrier 3000 Filled Sealed Trailer (Hub End) 75 (typ) Empty Sealed TAPE DIMENSIONS inches (millimeters) Package SC70-6 Tape Size 8 mm www.fairchildsemi.com DIM A DIM B 0.093 0.096 (2.35) (2.45) DIM F DIM Ko 0.138 0.004 0.053 0.004 (3.5 0.10) 6 (1.35 0.10) DIM P1 DIM W 0.157 0.315 0.004 (4) (8 0.1) TAPE FORMAT for MicroPak Package (Continued) Tape Number Cavity Section Cavities Status Status Leader (Start End) 125 (typ) Empty Sealed Designator L6X Cover Tape Carrier 5000 Filled Sealed Trailer (Hub End) 75 (typ) Empty Sealed REEL DIMENSIONS inches (millimeters) Tape Size 8 mm A B C D N W1 W2 W3 7.0 0.059 0.512 0.795 2.165 0.331 + 0.059/-0.000 0.567 W1 + 0.078/-0.039 (177.8) (1.50) (13.00) (20.20) (55.00) (8.40 + 1.50/-0.00) (14.40) (W1 + 2.00/-1.00) 7 www.fairchildsemi.com NC7SZ175 Tape and Reel Specification NC7SZ175 Physical Dimensions inches (millimeters) unless otherwise noted 6-Lead SC70, EIAJ SC88, 1.25mm Wide Package Number MAA06A www.fairchildsemi.com 8 NC7SZ175 TinyLogic UHS D-Type Flip-Flop with Asynchronous Clear Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 6-Lead MicroPak, 1.0mm Wide Package Number MAC06A Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications. LIFE SUPPORT POLICY FAIRCHILD'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. www.fairchildsemi.com 9 www.fairchildsemi.com