Philips Semiconductors Preliminary specification
Three quadrant triacs BTA208X series C
high commutation
GENERAL DESCRIPTION QUICK REFERENCE DATA
Glass passivated high commutation SYMBOL PARAMETER MAX. MAX. MAX. UNIT
triacs in a full pack, plastic envelope
intended for use in motor control BTA208X- 500C 600C 800C
circuitswherehighstaticanddynamic VDRM Repetitive peak off-state 500 600 800 V
dV/dt and high dI/dt can occur. These voltages
devices will commutate the full rated IT(RMS) RMS on-state current 8 8 8 A
rms current at the maximum rated ITSM Non-repetitive peak 65 65 65 A
junction temperature, without the aid on-state current
of a snubber.
PINNING - SOT186A PIN CONFIGURATION SYMBOL
PIN DESCRIPTION
1 main terminal 1
2 main terminal 2
3 gate
case isolated
LIMITING VALUES
Limiting values in accordance with the Absolute Maximum System (IEC 134).
SYMBOL PARAMETER CONDITIONS MIN. MAX. UNIT
-600 -600 -800
VDRM Repetitive peak off-state - 60016001800 V
voltages
IT(RMS) RMS on-state current full sine wave; - 8 A
Ths 73 ˚C
ITSM Non-repetitive peak full sine wave;
on-state current Tj = 25 ˚C prior to
surge
t = 20 ms - 65 A
t = 16.7 ms - 71 A
I2tI
2
t for fusing t = 10 ms - 21 A2s
dIT/dt Repetitive rate of rise of ITM = 12 A; IG = 0.2 A; 100 A/µs
on-state current after dIG/dt = 0.2 A/µs
triggering
IGM Peak gate current - 2 A
VGM Peak gate voltage - 5 V
PGM Peak gate power - 5 W
PG(AV) Average gate power over any 20 ms - 0.5 W
period
Tstg Storage temperature -40 150 ˚C
TjOperating junction - 125 ˚C
temperature
T1T2
G
123
case
1 Although not recommended, off-state voltages up to 800V may be applied without damage, but the triac may
switch to the on-state. The rate of rise of current should not exceed 6 A/µs.
October 1997 1 Rev 1.000
Philips Semiconductors Preliminary specification
Three quadrant triacs BTA208X series C
high commutation
ISOLATION LIMITING VALUE & CHARACTERISTIC
Ths = 25 ˚C unless otherwise specified
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
Visol R.M.S. isolation voltage from all f = 50-60 Hz; sinusoidal - 2500 V
three terminals to external waveform;
heatsink R.H. 65% ; clean and dustfree
Cisol Capacitance from T2 to external f = 1 MHz - 10 - pF
heatsink
THERMAL RESISTANCES
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
Rth j-hs Thermal resistance full or half cycle
junction to heatsink with heatsink compound - - 4.5 K/W
without heatsink compound - - 6.5 K/W
Rth j-a Thermal resistance in free air - 55 - K/W
junction to ambient
STATIC CHARACTERISTICS
Tj = 25 ˚C unless otherwise stated
SYMBOL PARAMETER CONDITIONS MIN. TYP. MAX. UNIT
IGT Gate trigger current2VD = 12 V; IT = 0.1 A T2+ G+ 2 - 35 mA
T2+ G- 2 - 35 mA
T2- G- 2 - 35 mA
ILLatching current VD = 12 V; IGT = 0.1 A T2+ G+ - - 20 mA
T2+ G- - - 30 mA
T2- G- - - 20 mA
IHHolding current VD = 12 V; IGT = 0.1 A - - 15 mA
VTOn-state voltage IT = 10 A - 1.3 1.65 V
VGT Gate trigger voltage VD = 12 V; IT = 0.1 A - 0.7 1.5 V
VD = 400 V; IT = 0.1 A; Tj = 125 ˚C 0.25 0.4 - V
IDOff-state leakage current VD = VDRM(max); Tj = 125 ˚C - 0.1 0.5 mA
DYNAMIC CHARACTERISTICS
Tj = 25 ˚C unless otherwise stated
SYMBOL PARAMETER CONDITIONS MIN. TYP. UNIT
dVD/dt Critical rate of rise of VDM = 67% VDRM(max); Tj = 125 ˚C; exponential 1000 - V/µs
off-state voltage waveform; gate open circuit
dIcom/dt Critical rate of change of VDM = 400 V; Tj = 125 ˚C; IT(RMS) = 8 A; without 3 14 A/ms
commutating current snubber; gate open circuit
tgt Gate controlled turn-on ITM = 12 A; VD = VDRM(max); IG = 0.1 A; - 2 µs
time dIG/dt = 5 A/µs
2 Device does not trigger in the T2-, G+ quadrant.
October 1997 2 Rev 1.000
Philips Semiconductors Preliminary specification
Three quadrant triacs BTA208X series C
high commutation
MECHANICAL DATA
Dimensions in mm
Net Mass: 2 g
Fig.1. SOT186A; The seating plane is electrically isolated from all terminals.
Notes
1. Refer to mounting instructions for F-pack envelopes.
2. Epoxy meets UL94 V0 at 1/8".
10.3
max
3.2
3.0
4.6
max
2.9 max
2.8
seating
plane
6.4
15.8
max
0.6
2.5
2.54
5.08
123
3 max.
not tinned
3
0.5
2.5
0.9
0.7
M
0.4
15.8
max. 19
max.
13.5
min.
Recesses (2x)
2.5
0.8 max. depth
1.0 (2x)
1.3
October 1997 3 Rev 1.000
Philips Semiconductors Preliminary specification
Three quadrant triacs BTA208X series C
high commutation
DEFINITIONS
Data sheet status
Objective specification This data sheet contains target or goal specifications for product development.
Preliminary specification This data sheet contains preliminary data; supplementary data may be published later.
Product specification This data sheet contains final product specifications.
Limiting values
Limiting values are given in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one
or more of the limiting values may cause permanent damage to the device. These are stress ratings only and
operation of the device at these or at any other conditions above those given in the Characteristics sections of
this specification is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
Philips Electronics N.V. 1997
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the
copyright owner.
The information presented in this document does not form part of any quotation or contract, it is believed to be
accurate and reliable and may be changed without notice. No liability will be accepted by the publisher for any
consequence of its use. Publication thereof does not convey nor imply any license under patent or other
industrial or intellectual property rights.
LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices or systems where malfunction of these
products can be reasonably expected to result in personal injury. Philips customers using or selling these products
for use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting
from such improper use or sale.
October 1997 4 Rev 1.000