MC74HC151DR2 - Motorola / Freescale Semiconductor



SEMICONDUCTOR TECHNICAL DATA

1REV 6

 Motorola, Inc. 1995

10/95

  



High–Performance Silicon–Gate CMOS

The MC74HC153 is identical in pinout to the LS153. The device inputs are

compatible with standard CMOS outputs; with pullup resistors, they are

compatible with LSTTL outputs.

The Address Inputs select one of four Data Inputs from each multiplexer.

Each multiplexer has an active–low Strobe control and a noninverting

output.

The HC153 is similar in function to the HC253, which has 3–state outputs.

•Output Drive Capability: 10 LSTTL Loads

•Outputs Directly Interface to CMOS, NMOS, and TTL

•Operating Voltage Range: 2 to 6 V

•Low Input Current: 1 µA

•High Noise Immunity Characteristic of CMOS Devices

•In Compliance with the Requirements Defined by JEDEC Standard

No. 7A

•Chip Complexity: 108 FETs or 27 Equivalent Gates

LOGIC DIAGRAM

D0a

STROBE a

ADDRESS

INPUTS

DATA–

WORD a

INPUTS

PIN 16 = VCC

PIN 8 = GND

A1 2

STROBE b

D1a

D2a

D3a

D0b

DATA–

WORD b

INPUTS

D1b

D2b

D3b



FUNCTION TABLE

PIN ASSIGNMENT

D0, D1, D2, and D3 = the level of the

respective data input.

Inputs Output

A1 A0 Strobe Y

X X H L

L L L D0

L H L D1

H L L D2

H H L D3

125

STROBE a

D3a

GND

D3b

STROBE b

VCC

D2a

D1a

D0a

D2b

D1b

D0b

D SUFFIX

SOIC PACKAGE

CASE 751B–05

N SUFFIX

PLASTIC PACKAGE

CASE 648–08

ORDERING INFORMATION

MC74HCXXXN

MC74HCXXXD Plastic

SOIC

MC74HC153

MOTOROLA High–Speed CMOS Logic Data

DL129 — Rev 6

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

MAXIMUM RATINGS*

ÎÎÎ

Symbol

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

Parameter

ÎÎÎÎÎÎ

Value

ÎÎÎ

Unit

ÎÎÎ

VCC

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

DC Supply Voltage (Referenced to GND)

ÎÎÎÎÎÎ

– 0.5 to + 7.0

ÎÎÎ

Vin

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

DC Input Voltage (Referenced to GND)

ÎÎÎÎÎÎ

– 1.5 to VCC + 1.5

ÎÎÎ

Vout

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

DC Output Voltage (Referenced to GND)

ÎÎÎÎÎÎ

– 0.5 to VCC + 0.5

ÎÎÎ

Iin

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

DC Input Current, per Pin

ÎÎÎÎÎÎ

± 20

ÎÎÎ

Iout

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

DC Output Current, per Pin

ÎÎÎÎÎÎ

± 25

ÎÎÎ

ICC

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

DC Supply Current, VCC and GND Pins

ÎÎÎÎÎÎ

± 50

ÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

Power Dissipation in Still Air Plastic DIP†

SOIC Package†

ÎÎÎÎÎÎ

750

500

ÎÎÎ

Tstg

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

Storage Temperature

ÎÎÎÎÎÎ

– 65 to + 150

ÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

Lead Temperature, 1 mm from Case for 10 Seconds

(Plastic DIP or SOIC Package)

ÎÎÎÎÎÎ

260

ÎÎÎ

*Maximum Ratings are those values beyond which damage to the device may occur.

Functional operation should be restricted to the Recommended Operating Conditions.

†Derating — Plastic DIP: – 10 mW/

C from 65

to 125

SOIC Package: – 7 mW/

C from 65

to 125

For high frequency or heavy load considerations, see Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D).

RECOMMENDED OPERATING CONDITIONS

ÎÎÎÎ

Symbol

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

Parameter

ÎÎÎ

Min

ÎÎÎ

Max

ÎÎÎ

Unit

ÎÎÎÎ

VCC

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

DC Supply Voltage (Referenced to GND)

ÎÎÎ

2.0

ÎÎÎ

6.0

ÎÎÎ

ÎÎÎÎ

Vin, Vout

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

DC Input Voltage, Output Voltage (Referenced to GND)

ÎÎÎ

VCC

ÎÎÎ

ÎÎÎÎ

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

Operating Temperature, All Package Types

ÎÎÎ

– 55

ÎÎÎ

+ 125

ÎÎÎ

ÎÎÎÎ

tr, tf

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

Input Rise and Fall Time VCC = 2.0 V

(Figure 1) VCC = 4.5 V

VCC = 6.0 V

ÎÎÎ

1000

500

400

ÎÎÎ

DC ELECTRICAL CHARACTERISTICS (Voltages Referenced to GND)

ÎÎÎÎ

Symbol

ÎÎÎÎÎÎÎÎÎ

Parameter

ÎÎÎÎÎÎÎÎÎ

Test Conditions

ÎÎÎÎ

VCC

ÎÎÎÎÎÎÎÎÎ

Guaranteed Limit

ÎÎÎ

Unit

ÎÎÎÎ

Symbol

ÎÎÎÎÎÎÎÎÎ

Parameter

ÎÎÎÎÎÎÎÎÎ

Test Conditions

ÎÎÎÎ

VCC

ÎÎÎ

– 55 to

ÎÎÎÎ

125

ÎÎÎ

Unit

ÎÎÎÎ

VIH

ÎÎÎÎÎÎÎÎÎ

Minimum High–Level Input

Voltage

ÎÎÎÎÎÎÎÎÎ

Vout = 0.1 V or VCC – 0.1 V

|Iout|

20 µA

ÎÎÎÎ

2.0

4.5

6.0

ÎÎÎ

1.5

3.15

4.2

ÎÎÎÎ

1.5

3.15

4.2

ÎÎÎÎ

1.5

3.15

4.2

ÎÎÎ

ÎÎÎÎ

VIL

ÎÎÎÎÎÎÎÎÎ

Maximum Low–Level Input

Voltage

ÎÎÎÎÎÎÎÎÎ

Vout = 0.1 V or VCC – 0.1 V

|Iout|

20 µA

ÎÎÎÎ

2.0

4.5

6.0

ÎÎÎ

0.3

0.9

1.2

ÎÎÎÎ

0.3

0.9

1.2

ÎÎÎÎ

0.3

0.9

1.2

ÎÎÎ

ÎÎÎÎ

VOH

ÎÎÎÎÎÎÎÎÎ

Minimum High–Level Output

Voltage

ÎÎÎÎÎÎÎÎÎ

Vin = VIH or VIL

|Iout|

20 µA

ÎÎÎÎ

2.0

4.5

6.0

ÎÎÎ

1.9

4.4

5.9

ÎÎÎÎ

1.9

4.4

5.9

ÎÎÎÎ

1.9

4.4

5.9

ÎÎÎ

ÎÎÎÎ

ÎÎÎÎÎÎÎÎÎ

Vin = VIH or VIL |Iout|

4.0 mA

|Iout|

5.2 mA

ÎÎÎÎ

4.5

6.0

ÎÎÎ

3.98

5.48

ÎÎÎÎ

3.84

5.34

ÎÎÎÎ

3.70

5.20

ÎÎÎ

ÎÎÎÎ

VOL

ÎÎÎÎÎÎÎÎÎ

Maximum Low–Level Output

Voltage

ÎÎÎÎÎÎÎÎÎ

Vin = VIH or VIL

|Iout|

20 µA

ÎÎÎÎ

2.0

4.5

6.0

ÎÎÎ

0.1

ÎÎÎÎ

0.1

ÎÎÎÎ

0.1

ÎÎÎ

ÎÎÎÎ

ÎÎÎÎÎÎÎÎÎ

Vin = VIH or VIL |Iout|

4.0 mA

|Iout|

5.2 mA

ÎÎÎÎ

4.5

6.0

ÎÎÎ

0.26

ÎÎÎÎ

0.33

ÎÎÎÎ

0.40

ÎÎÎ

ÎÎÎÎ

Iin

ÎÎÎÎÎÎÎÎÎ

Maximum Input Leakage Current

ÎÎÎÎÎÎÎÎÎ

Vin = VCC or GND

ÎÎÎÎ

6.0

ÎÎÎ

± 0.1

ÎÎÎÎ

± 1.0

ÎÎÎÎ

± 1.0

ÎÎÎ

µA

ÎÎÎÎ

ICC

ÎÎÎÎÎÎÎÎÎ

Maximum Quiescent Supply

Current (per Package)

ÎÎÎÎÎÎÎÎÎ

Vin = VCC or GND

Iout = 0 µA

ÎÎÎÎ

6.0

ÎÎÎ

ÎÎÎÎ

160

ÎÎÎ

µA

NOTE:Information on typical parametric values can be found in Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D).

This device contains protection

circuitry to guard against damage

due to high static voltages or electric

fields. However, precautions must

be taken to avoid applications of any

voltage higher than maximum rated

voltages to this high–impedance cir-

cuit. For proper operation, Vin and

Vout should be constrained to the

range GND

(Vin or V out)

VCC.

Unused inputs must always be

tied to an appropriate logic voltage

level (e.g., either GND or VCC).

Unused outputs must be left open.

MC74HC153

High–Speed CMOS Logic Data

DL129 — Rev 6 3 MOTOROLA

AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6 ns)

ÎÎÎÎ

Symbol

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

Parameter

ÎÎÎÎ

VCC

ÎÎÎÎÎÎÎÎÎ

Guaranteed Limit

ÎÎÎ

Unit

ÎÎÎÎ

Symbol

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

Parameter

ÎÎÎÎ

VCC

ÎÎÎ

– 55 to

ÎÎÎÎ

125

ÎÎÎ

Unit

ÎÎÎÎ

tPLH,

tPHL

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

Maximum Propagation Delay, Input D to Output Y

(Figures 1, and 4)

ÎÎÎÎ

2.0

4.5

6.0

ÎÎÎ

140

ÎÎÎÎ

175

ÎÎÎÎ

210

ÎÎÎ

ÎÎÎÎ

tPLH,

tPHL

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

Maximum Propagation Delay, Input A to Output Y

(Figures 2 and 4)

ÎÎÎÎ

2.0

4.5

6.0

ÎÎÎ

175

ÎÎÎÎ

220

ÎÎÎÎ

265

ÎÎÎ

ÎÎÎÎ

tPLH,

tPHL

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

Maximum Propagation Delay, Strobe to Output Y

(Figures 3, and 4)

ÎÎÎÎ

2.0

4.5

6.0

ÎÎÎ

ÎÎÎÎ

120

ÎÎÎÎ

145

ÎÎÎ

ÎÎÎÎ

tTLH,

tTHL

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

Maximum Output Transition Time, Any Output

(Figures 1 and 4)

ÎÎÎÎ

2.0

4.5

6.0

ÎÎÎ

ÎÎÎÎ

110

ÎÎÎ

ÎÎÎÎ

Cin

ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ

Maximum Input Capacitance

ÎÎÎÎ

—

ÎÎÎ

ÎÎÎÎ

ÎÎÎ

NOTES:

1. For propagation delays with loads other than 50 pF, see Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D).

2. Information on typical parametric values can be found in Chapter 2 of the Motorola High–Speed CMOS Data Book (DL129/D).

CPD

Power Dissipation Capacitance (Per Multiplexer)*

Typical @ 25°C, VCC = 5.0 V

CPD Power Dissipation Capacitance (Per Multiplexer)*

*Used to determine the no–load dynamic power consumption: PD = CPD VCC2f + ICC VCC. For load considerations, see Chapter 2 of the

Motorola High–Speed CMOS Data Book (DL129/D).

SWITCHING WAVEFORMS

Figure 1. Figure 2.

tPHL

tPLH

tTHL

tTLH

STROBE 10%

50%

VCC

GND

INPUT D

OUTPUT Y

10%

50%

90%

10%

50%

90%

tTLH

tPLH tPHL

tTHL

VCC

GND

VCC

GND

50%

INPUT A

tPLH tPHL

50%

OUTPUT Y

10%

50%

90%

OUTPUT Y

*Includes all probe and jig capacitance

CL*

TEST POINT

DEVICE

UNDER

TEST

OUTPUT

Figure 3. Figure 4. Test Circuit

VALIDVALID

MC74HC153

MOTOROLA High–Speed CMOS Logic Data

DL129 — Rev 6

PIN DESCRIPTIONS

DATA INPUTS

D0a – D3a, D0b – D3b (Pins 3, 4, 5, 6, 10, 11, 12, 13)

Data Inputs. With the outputs enabled, the addressed Data

Inputs appear at the Y outputs.

CONTROL INPUTS

A0, A1 (Pins 2, 14)

Address Inputs. These inputs address the pair of Data

Inputs which appear at the corresponding outputs.

Strobe (Pins 1, 15)

Active–low Strobe. A low level applied to these pins en-

ables the corresponding outputs.

OUTPUTS

Ya, Yb (Pins 7, 9)

Noninverting data outputs.

DATA

WORD a

INPUTS

ADDRESS

INPUTS

EXPANDED LOGIC DIAGRAM

DATA

WORD b

INPUTS

NONINVERTING

DATA

OUTPUTS

D0aSTROBE a

13 15

STROBE b

D1a

D2a

D3a

D0b

D1b

D2b

D3b

MC74HC153

High–Speed CMOS Logic Data

DL129 — Rev 6 5 MOTOROLA

OUTLINE DIMENSIONS

N SUFFIX

PLASTIC PACKAGE

CASE 648–08

ISSUE R

MIN MINMAX MAX

INCHES MILLIMETERS

DIM

18.80

6.35

3.69

0.39

1.02

0.21

2.80

7.50

0.51

19.55

6.85

4.44

0.53

1.77

0.38

3.30

7.74

1.01

0.740

0.250

0.145

0.015

0.040

0.008

0.110

0.295

0.020

0.770

0.270

0.175

0.021

0.070

0.015

0.130

0.305

0.040

NOTES:

1. DIMENSIONING AND TOLERANCING PER ANSI

Y14.5M, 1982.

2. CONTROLLING DIMENSION: INCH.

3. DIMENSION L TO CENTER OF LEADS WHEN

FORMED PARALLEL.

4. DIMENSION B DOES NOT INCLUDE MOLD FLASH.

5. ROUNDED CORNERS OPTIONAL.

2.54 BSC

1.27 BSC

0.100 BSC

0.050 BSC

–A

–

1 8

916

HGD 16 PL

–T

–

SEATING

PLANE

KJM

T A0.25 (0.010) M M

0.25 (0.010) T B A

MS S

MIN MINMAX MAX

MILLIMETERS INCHES

DIM

9.80

3.80

1.35

0.35

0.40

0.19

0.10

5.80

0.25

10.00

4.00

1.75

0.49

1.25

0.25

6.20

0.50

0.386

0.150

0.054

0.014

0.016

0.008

0.004

0.229

0.010

0.393

0.157

0.068

0.019

0.049

0.009

0.244

0.019

1.27 BSC 0.050 BSC

NOTES:

1. DIMENSIONING AND TOLERANCING PER ANSI

Y14.5M, 1982.

2. CONTROLLING DIMENSION: MILLIMETER.

3. DIMENSIONS A AND B DO NOT INCLUDE

MOLD PROTRUSION.

4. MAXIMUM MOLD PROTRUSION 0.15 (0.006)

PER SIDE.

5. DIMENSION D DOES NOT INCLUDE DAMBAR

PROTRUSION. ALLOWABLE DAMBAR

PROTRUSION SHALL BE 0.127 (0.005) TOTAL

IN EXCESS OF THE D DIMENSION AT

MAXIMUM MATERIAL CONDITION.

916

–A

–

–B

–

D16 PL

–T

–

SEATING

PLANE

R X 45°

P 8 PL

0.25 (0.010) B

M M

D SUFFIX

PLASTIC SOIC PACKAGE

CASE 751B–05

ISSUE J

How to reach us:

USA/EUROPE: Motorola Literature Distribution; JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, Toshikatsu Otsuki,

P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–3521–8315

MFAX: RMFAX0@email.sps.mot.com –TOUCHTONE (602) 244–6609 HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park,

INTERNET: http://Design–NET.com 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298

Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty , representation or guarantee regarding

the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit,

and specifically disclaims any and all liability , including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different

applications. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does

not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in

systems intended for surgical implant into the body , or other applications intended to support or sustain life, or for any other application in which the failure of

the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such

unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless

against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death

associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part.

Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer .

MC74HC153/D

*MC74HC153/D*

◊CODELINE