Data Sheet March 2008 CC030-Series Power Modules; dc-dc Converters: 18 Vdc to 36 Vdc Inputs, 30 W Features n The CC030-Series Power Modules use advanced, surfacemount technology and deliver high-quality, compact, dc-dc conversion at an economical price. Options n Choice of remote on/off logic configuration n Case ground pin n Short pins: 2.79 mm 0.25 mm (0.110 in. 0.010 in.) Small size: 61.0 mm x 71.1 mm x 12.7 mm (2.40 in. x 2.80 in. x 0.50 in.) n Low output noise n Constant frequency n Industry-standard pinout n Metal case n 2:1 input voltage range n High efficiency: 81% typical n Positive remote on/off logic n Remote sense n Adjustable output voltage: 90% to 110% of VO, nom n n UL* 1950 Recognized, CSA C22.2 No. 950-95 Certified, VDE 0805 (EN60950, IEC950) Licensed Within FCC Class A Radiated Limits Applications n Distributed power architectures n Communication equipment n Computer equipment Description The CC030-Series Power Modules are dc-dc converters that operate over an input voltage range of 18 Vdc to 36 Vdc and provide precisely regulated outputs. The outputs are isolated from the inputs, allowing versatile polarity configurations and grounding connections. The modules have maximum power ratings of 30 W at a typical full-load efficiency of 81%. The power modules feature remote on/off, output sense (both negative and positive leads), and output voltage adjustment from 90% to 110% of the nominal output voltage. For diskdrive applications, the CC030B Power Module provides a motor-start surge current of 3 A. The modules are PC board-mountable and encapsulated in metal cases. The modules are rated to full load at 100 C case temperature. * UL is a registered trademark of Underwriters Laboratories, Inc. CSA is a registered trademark of Canadian Standards Association. VDE is a trademark of Verband Deutscher Elektrotechniker e.V. CC030-Series Power Modules; dc-dc Converters: 18 Vdc to 36 Vdc Inputs, 30 W Data Sheet March 2008 Absolute Maximum Ratings Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings only. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operations sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect device reliability. Parameter Symbol Min Max Unit Input Voltage (continuous) VI -- 50 Vdc Operating Case Temperature (See Thermal Considerations section.) TC -40 100 C Storage Temperature Tstg -40 110 C I/O Isolation Voltage: Continuous Transient (1 min) -- -- -- -- 500 800 Vdc V Electrical Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. Table 1. Input Specifications Parameter Symbol Min Typ Max Unit VI 18 24 36 Vdc II, max -- -- 3.0 A Inrush Transient i2 t -- -- 0.2 A2s Input Reflected-Ripple Current, Peak-to-Peak (0.5 Hz to 20 MHz, 12 source impedance; see Figure 14 and Design Considerations.) II -- 30 -- mAp-p Input Ripple Rejection (120 Hz) -- -- 60 -- dB Operating Input Voltage Maximum Input Current (VI = 0 V to 75 V; IO = IO, max; see Figure 1.) Fusing Considerations CAUTION: This power module is not internally fused. An input line fuse must always be used. This encapsulated power module can be used in a wide variety of applications, ranging from simple stand-alone operation to an integrated part of a sophisticated power architecture. To preserve maximum flexibility, internal fusing is not included; however, to achieve maximum safety and system protection, always use an input line fuse. The safety agencies require a normal-blow fuse with a maximum rating of 5 A in series with the input (see Safety Considerations section). Based on the information provided in this data sheet on inrush energy and maximum dc input current, the same type of fuse with a lower rating can be used. Refer to the fuse manufacturer's data for further information. 2 Lineage Power CC030-Series Power Modules; dc-dc Converters: 18 Vdc to 36 Vdc Inputs, 30 W Data Sheet March 2008 Electrical Specifications (continued) Table 2. Output Specifications Parameter Device Symbol Min Typ Max Unit Output Voltage Set Point (VI = 24 V; IO = IO, max; TC = 25 C) CC030A CC030B CC030C VO, set VO, set VO, set 4.90 11.76 14.70 5.0 12.0 15.0 5.10 12.24 15.30 Vdc Vdc Vdc Output Voltage (Over all operating input voltage, resistive load, and temperature conditions until end of life; see Figure 15.) CC030A CC030B CC030C VO VO VO 4.80 11.52 14.40 -- -- -- 5.20 12.48 15.60 Vdc Vdc Vdc All All All -- -- -- -- -- -- 0.01 0.05 0.5 0.1 0.1 1.5 %VO %VO %VO CC030A CC030B, C CC030A CC030B, C -- -- -- -- -- -- -- -- -- -- -- -- 20 25 150 200 mVrms mVrms mVp-p mVp-p All -- 0 -- 4700 F Output Current (At IO < IO, min, the modules may exceed output ripple specifications.) CC030A CC030B CC030B CC030C IO IO IO, trans IO 0.6 0.3 -- 0.2 -- -- -- -- 6.0 2.5 3.0 2.0 A A A A Output Current-limit Inception (VO = 90% of VO, nom) CC030A CC030B CC030C IO IO IO -- -- -- 6.9 3.6 2.5 -- -- -- A A A Output Short-circuit Current (VO = 250 mV) CC030A CC030B CC030C -- -- -- -- -- -- 8.0 4.0 3.0 -- -- -- A A A CC030A CC030B, C 78 80 81 81 -- -- % % All -- -- 250 -- kHz All All -- -- -- -- 2 0.5 -- -- %VO, set ms All All -- -- -- -- 2 0.5 -- -- %VO, set ms Output Regulation: Line (VI = 18 V to 36 V) Load (IO = IO, min to IO, max) Temperature (TC = -40 C to +100 C) Output Ripple and Noise Voltage: RMS Peak-to-peak (5 Hz to 20 MHz) External Load Capacitance Efficiency (VI = 24 V; IO = IO, max; TC = 25 C; see Figures 8--10 and 15.) Switching Frequency Dynamic Response (yIO/yt = 1 A/10 s, VI = 24 V, TC = 25 C): Load Change from IO = 50% to 75% of IO, max (See Figure 11.): Peak Deviation Settling Time (VO < 10% peak deviation) Load Change from IO = 50% to 25% of IO, max (See Figure 12.): Peak Deviation Settling Time (VO < 10% of peak deviation) Lineage Power 3 CC030-Series Power Modules; dc-dc Converters: 18 Vdc to 36 Vdc Inputs, 30 W Data Sheet March 2008 Electrical Specifications (continued) Table 3. Isolation Specifications Parameter Min Typ Max Unit Isolation Capacitance -- 0.02 -- F Isolation Resistance 10 -- -- M3/4 Min Typ Max Unit 113 (4.0) g (oz.) General Specifications Parameter Calculated MTBF (IO = 80% of IO, max; TC = 40 C) 3,900,000 Weight -- hours -- Feature Specifications Unless otherwise indicated, specifications apply over all operating input voltage, resistive load, and temperature conditions. See Feature Descriptions and Design Considerations for further information. Parameter Device Symbol Min Typ Max Unit All Ion/off -- -- 1.0 mA All All Von/off Von/off -0.7 -- -- -- 1.2 6 V V All Ion/off -- -- 50 A All Von/off -- -- 1.2 V All -- -- -- 5 ms All -- -- 0 5 % Output Voltage Sense Range All -- -- -- 0.5 V Output Voltage Set Point Adjustment Range (See Feature Descriptions.) All Vtrim 90 -- 110 %VO, nom CC030A CC030B CC030C VO, clamp VO, clamp VO, clamp 5.6 13.0 17.0 -- -- -- 7.0 16.0 20.0 V V V Remote On/Off (VI = 18 V to 36 V; open collector or equivalent compatible; signal referenced to VI(-) terminal. See Figure 16 and Feature Descriptions.): Logic Low--Module Off Logic High--Module On Module Specifications: On/Off Current--Logic Low On/Off Voltage: Logic Low Logic High (Ion/off = 0) Open-collector Switch Specifications: Leakage Current During Logic High (Von/off = 10 V) Output Low Voltage During Logic Low (Ion/off = 1 mA) Turn-on Time (@ 80% of IO, max; TA = 25 C; VO within 1% of steady state) Output Voltage Overshoot (See Figure 13.) Output Overvoltage Protection (clamp) 4 Lineage Power Data Sheet March 2008 CC030-Series Power Modules; dc-dc Converters: 18 Vdc to 36 Vdc Inputs, 30 W Characteristic Curves 12 10 2.5 8 V I = 18 V V I = 27 V 6 V I = 36 V 2.0 1.5 4 1.0 2 0.5 0 0 1 2 3 4 5 6 0.0 0 5 10 15 20 25 INPUT VOLTAGE, V 30 35 40 OUTPUT CURRENT, I O (A) 8-722(C).a I (V) 8-724(C) Figure 3. CC030B Typical Output Characteristics Figure 1. CC030-Series Typical Input Characteristic 16 14 12 5 10 4 V I = 18 V V I = 36 V 6 V I = 24 V 3 V I = 18 V V I = 27 V 8 V I = 36 V 4 2 2 0 1 0 0.5 1.0 1.5 2.0 2.5 3.0 OUTPUT CURRENT, I 0 0 1 2 3 4 5 6 OUTPUT CURRENT, I 7 O 8 9 10 (A) 8-721(C) 3.5 O 4.0 4.5 5.0 (A) 8-723(C).a Figure 4. CC030C Typical Output Characteristics Figure 2. CC030A Typical Output Characteristics Lineage Power 5 CC030-Series Power Modules; dc-dc Converters: 18 Vdc to 36 Vdc Inputs, 30 W Data Sheet March 2008 Characteristic Curves (continued) 15.05 15.00 5.010 5.005 14.95 5.000 4.995 14.90 4.990 4.985 14.85 4.980 4.975 14.80 -40 4.970 -20 4.965 4.960 -40 20 0 60 40 80 100 CASE TEMPERATURE, T C (C) -20 0 20 40 60 80 100 8-854(C) CASE TEMPERATURE, T C (C) 8-852(C) Figure 5. CC030A Typical Output Voltage Variation over Ambient Temperature Range Figure 7. CC030C Typical Output Voltage Variation over Ambient Temperature Range 90 12.02 12.00 80 11.98 V I = 36 V V I = 24 V 70 11.96 V I = 18 V 11.94 60 11.92 11.90 -40 50 -20 0 20 40 60 80 100 0 1 2 3 OUTPUT CURRENT, I CASE TEMPERATURE, T C (C) 4 O 5 6 (A) 8-727(C).a 8-853(C) Figure 6. CC030B Typical Output Voltage Variation over Ambient Temperature Range 6 Figure 8. CC030A Typical Converter Efficiency vs. Output Current Lineage Power Data Sheet March 2008 CC030-Series Power Modules; dc-dc Converters: 18 Vdc to 36 Vdc Inputs, 30 W Characteristic Curves (continued) 90 102 V I = 18 V 100 80 70 98 V I = 36 V V I = 24 V 75 60 50 50 *lo *t = 1 A/10 s 25 500 s 40 0 0.5 1.0 1.5 2.0 OUTPUT CURRENT, I 2.5 O 3.0 TIME, t (500 s/div) 8-731(C).a (A) 8-726(C).b Figure 9. CC030B Typical Converter Efficiency vs. Output Current 90 V I = 18 V Figure 11. Typical Output Voltage for a Step Load Change from 50% to 75% 102 80 100 V I = 24 V V I = 36 V 70 98 60 75 50 50 *lo *t = 1 A/10 s 25 40 500 s 0 0.2 0.4 0.6 0.8 1.0 1.2 OUTPUT CURRENT, I 1.4 O 1.6 1.8 2.0 TIME, t (500 s/div) (A) 8-725(C) Figure 10. CC030C Typical Converter Efficiency vs. Output Current Lineage Power 8-732(C).a Figure 12. Typical Output Voltage for a Step Load Change from 50% to 25% 7 CC030-Series Power Modules; dc-dc Converters: 18 Vdc to 36 Vdc Inputs, 30 W Data Sheet March 2008 Characteristic Curves (continued) SENSE(+) V I(+) CONTACT AND DISTRIBUTION LOSSES V O (+) IO II LOAD SUPPLY 100 V I(-) 50 CONTACT RESISTANCE V O (-) SENSE(-) 0 8-749(C) Note: All measurements are taken at the module terminals. When socketing, place Kelvin connections at module terminals to avoid measurement errors due to socket contact resistance. [ V O (+) - V O (-) ] I O = --------------------------------------------------- x 100 [ V I (+) - V I (-) ] II 4 % 2 Figure 15. Output Voltage and Efficiency Measurement Test Setup 0 Design Considerations TIME, t (1 ms/div) 8-2825(C) Figure 13. Typical Output Voltage Start-Up when Signal Applied to Remote On/Off Test Configurations Grounding Considerations For modules without the isolated case pin option, the case is internally connected to the VI(-) pin. For modules with the isolated case pin option, device code suffix "7," the case is not connected internally allowing the user flexibility in grounding. T O OSC ILLOSC OPE LT E S T C U R R EN T PR OBE VI ( + ) 12 H BAT T ER Y C S 220 F IMPED AN C E < 0.1 * @ 20 C , 100 kH z V I ( -) 8-489(C) Note: Input reflected-ripple current is measured with a simulated source impedance of 12 H. Capacitor Cs offsets possible battery impedance. Current is measured at the input of the module. Figure 14. Input Reflected-Ripple Test Setup 8 Lineage Power Data Sheet March 2008 CC030-Series Power Modules; dc-dc Converters: 18 Vdc to 36 Vdc Inputs, 30 W Design Considerations (continued) Remote On/Off Input Source Impedance To turn the power module on and off, the user must supply a switch to control the voltage between the on/off terminal and the VI(-) terminal (Von/off). The switch can be an open collector or equivalent (see Figure 16). A logic low is Von/off = -0.7 V to 1.2 V, during which the module is off. The maximum Ion/off during a logic low is 1 mA. The switch should maintain a logiclow voltage while sinking 1 mA. The power module should be connected to a low ac-impedance input source. Source inductance greater than 12 H can affect the stability of the power module. A 33 F electrolytic capacitor (ESR < 0.7 3/4 at 100 kHz) mounted close to the power module helps ensure stability of the unit. For other highly inductive source impedances, consult the factory for further application guidelines. (See Figure 14.) Safety Considerations For safety-agency approval of the system in which the power module is used, the power module must be installed in compliance with the spacing and separation requirements of the end-use safety agency standard, i.e., UL 1950, CSA C22.2 No. 950-95, and VDE 0805 (EN60950, IEC950). For the converter output to be considered meeting the requirements of safety extra-low voltage (SELV), the input must meet SELV requirements. The power module has extra-low voltage (ELV) outputs when all inputs are ELV. During a logic high, the maximum Von/off generated by the power module is 6 V. The maximum allowable leakage current of the switch at Von/off = 6 V is 50 A. The module has internal capacitance to reduce noise at the ON/OFF pin. Additional capacitance is not generally needed and may degrade the start-up characteristics of the module. V I (+) V I (-) - SENSE(+) V on/off V O (+) + Ion/off REMOTE ON/OFF The input to these units is to be provided with a maximum 5 A normal-blow fuse in the ungrounded lead. V O (-) LOAD SENSE(-) 8-720(C).i Figure 16. Remote On/Off Implementation Feature Descriptions Overcurrent Protection To provide protection in a fault (output overload) condition, the unit is equipped with internal current-limiting circuitry and can endure current limiting for an unlimited duration. At the point of current-limit inception, the unit shifts from voltage control to current control. If the output voltage is pulled very low during a severe fault, the current-limit circuit can exhibit either foldback or tailout characteristics (output-current decrease or increase). The unit operates normally once the output current is brought back into its specified range. Lineage Power Remote Sense Remote sense minimizes the effects of distribution losses by regulating the voltage at the remote-sense connections. The voltage between the remote-sense pins and the output terminals must not exceed the output voltage sense range given in the Feature Specifications table, for example, for the CC030Bs: [VO(+) - VO(-)] - [SENSE(+) - SENSE(-)] 0.5 V The voltage between the VO(+) and VO(-) terminals must not exceed 13.2 V. This limit includes any increase in voltage due to remote-sense compensation, set-point adjustment, and trim (see Figure 17). 9 CC030-Series Power Modules; dc-dc Converters: 18 Vdc to 36 Vdc Inputs, 30 W Feature Descriptions (continued) Data Sheet March 2008 The CC030-Series Power Modules have a fixed current-limit set point. Therefore, as the output voltage is adjusted down, the available output power is reduced. In addition, the minimum output current is a function of the output voltage. As the output voltage is adjusted down, the minimum required output current can increase. Remote Sense (continued) SENSE(+) SENSE(-) V I (-) SUPPLY II V O (-) IO V I (+) V I (+) LOAD V O (+) CONTACT AND DISTRIBUTION LOSSES CONTACT RESISTANCE ON/OFF V O (+) SENSE(+) R LOAD TRIM 8-651(C).n R adj-up V I (-) Figure 17. Effective Circuit Configuration for Single-Module Remote-Sense Operation SENSE (-) V O ( -) 8-715(C).c Output Voltage Adjustment Output voltage adjustment allows the user to increase or decrease the output voltage set point of a module. This is accomplished by connecting an external resistor between the TRIM pin and either the SENSE(+) or SENSE(-) pins (see Figures 18 and 19). With an external resistor between the TRIM and SENSE(-) pins (Radj-up), the output voltage set point (VO, adj) increases. R ad j -u p 2.5 x R 1 = ---------------------------------- k V O, adj - V O, nom The value of the internal resistor R1 is shown in Table 4. Table 4. Internal Resistor Values BMPM Code R1 CC030A CC030B CC030C 16.940 15.732 16.670 With an external resistor connected between the TRIM and SENSE(+) pins (Radj-down), the output voltage set point (VO, adj) decreases. R ad j- d ow n ( V O, adj - 2.5 ) x R 1 = ------------------------------------------ k V O, nom - V O, adj The combination of the output voltage adjustment range and the output voltage sense range given in the Feature Specifications table cannot exceed 110% of the nominal output voltage between the Vo(+) and Vo(-) terminals. 10 Figure 18. Circuit Configuration to Increase Output Voltage V I (+) ON/OFF V O (+) SENSE(+) R adj-down TRIM V I (-) R LOAD SENSE(-) V O (-) 8-748(C).c Figure 19. Circuit Configuration to Decrease Output Voltage Output Overvoltage Protection The output overvoltage clamp consists of control circuitry, which is independent of the primary regulation loop that monitors the voltage on the output terminals. The control loop of the clamp has a higher voltage set point than the primary loop (see Feature Specifications table). This provides a redundant voltage-control that reduces the risk of output overvoltage. Lineage Power CC030-Series Power Modules; dc-dc Converters: 18 Vdc to 36 Vdc Inputs, 30 W Data Sheet March 2008 Thermal Considerations Basic Thermal Performance The CC030-Series Power Modules are designed to operate in a variety of thermal environments. As with any electronic component, sufficient cooling must be provided to help ensure reliable operation. Heat-dissipating components inside the module are thermally coupled to the case to enable heat removal by conduction, convection, and radiation to the surrounding environment. The CC030-Series Power Modules are constructed with a specially designed, heat spreading enclosures. As a result, full load operation in natural convection at 50 C can be achieved without the use of an external heat sink. The thermal data presented is based on measurements taken in a wind tunnel. The test setup shown in Figure 20 was used to collect data for Figures 24 and 25. Higher ambient temperatures can be sustained by increasing the airflow or by adding a heat sink. As stated, this data is based on a maximum case temperature of 100 C and measured in the test configuration shown in Figure 20. The graphs in Figures 21 through 23 provide general guidelines for use. Actual performance can vary depending on the particular application environment. The maximum case temperature of 100 C must not be exceeded. 12.7 (0.50) WIND TUNNEL WALL MEASURE CASE TEMPERATURE (T C ) AT CENTER OF UNIT AIRFLOW CONNECTORS TO LOADS, POWER SUPPLIES, AND DATALOGGER, 6.35 (0.25) TALL 203.2 (8.00) AIRFLOW 101.6 (4.00) 76.2 (3.00) AIR VELOCITY AND AMBIENT TEMPERATURE MEASURED BELOW THE MODULE 203.2 (8.00) 19.1 (0.75) 8-1046(C) Figure 20. Thermal Test Setup Lineage Power 11 CC030-Series Power Modules; dc-dc Converters: 18 Vdc to 36 Vdc Inputs, 30 W Data Sheet March 2008 Thermal Considerations (continued) 6 Forced Convection Cooling 5 To determine the necessary airflow, determine the power dissipated by the unit for the particular application. Figures 21 through 23 show typical power dissipation for these power modules over a range of output currents. With the known power dissipation and a given local ambient temperature, the appropriate airflow can be chosen from the derating curves in Figure 24. For example, if the unit dissipates 6.2 W, the minimum airflow in a 80 C environment is 1.0 ms-1 (200 ft./min). V I = 24 V V I = 36 V 4 3 2 V I = 18 V 1 0 0.0 0.2 0.4 0.6 0.8 1.0 1.2 OUTPUT CURRENT, I 1.4 O 1.6 1.8 2.0 (A) 8-1212(C).a 9 8 Figure 23. CC030C Power Dissipation vs. Output Current 7 6 V I = 36 V 5 V I = 27 V V I = 18 V 4 3 9 2 8 1 7 0 0 1 2 3 4 OUTPUT CURRENT, I O 5 6 6 5 (A) 3.0 ms 2.0 ms 1.0 ms 0.5 ms 4 8-1154(C).b 3 2 Figure 21. CC030A Power Dissipation vs. Output Current -1 (600 ft./min.) (400 ft./min.) -1 (200 ft./min.) -1 (100 ft./min.) NATURAL CONVECTION -1 1 0 30 40 50 60 70 LOCAL AMBIENT TEMPERATURE, T 80 90 A 100 (C) 8-1155(C) 7 6 Figure 24. Forced Convection Power Derating with No Heat Sink; Either Orientation V I = 36 V V I = 27 V 5 4 3 V I = 18 V 2 1 0 0.0 0.5 1.0 1.5 OUTPUT CURRENT, I 2.0 O 2.5 (A) 8-1211(C) Figure 22. CC030B Power Dissipation vs. Output Current 12 Lineage Power Data Sheet March 2008 CC030-Series Power Modules; dc-dc Converters: 18 Vdc to 36 Vdc Inputs, 30 W Thermal Considerations (continued) Although the previous example uses 100 C as the maximum case temperature, for extremely high-reliability applications, one can use a lower temperature for Tc, max. Heat Sink Selection Several heat sinks are available for these modules. The case includes through threaded mounting holes allowing attachment of heat sinks or cold plates from either side of the module. The mounting torque must not exceed 0.56 N-m (5 in.-lb). Figure 25 shows the case-to-ambient thermal resistance, (C/W), for these modules. These curves can be used to predict which heat sink will be needed for a particular environment. For example, if the unit dissipates 7.1 W of heat in an 80 C environment with an airflow of 0.5 ms-1 (100 ft./min.), the minimum heat sink required can be determined as follows: ( T C, max - T A ) P D where: Tc, max TA = = = PD = module's total thermal resistance case temperature (See Figure 20.) inlet ambient temperature (See Figure 20.) power dissipation (100 - 80)/7.1 2.8 C/W It is important to point out that the thermal resistances shown in Figure 25 are for heat transfer from the sides and bottom of the module as well as the top side with the attached heat sink; therefore, the case-to-ambient thermal resistances shown will generally be lower than the resistance of the heat sink by itself. The data in Figure 25 was taken with a thermally conductive dry pad between the case and the heat sink to minimize contact resistance (typically 0.1 C/W to 0.3 C/W). For a more detailed explanation of thermal energy management for this series of power modules as well as more details on available heat sinks, please request the following technical note: Thermal Energy Management CC-, CW-, DC-, and DW-Series 25 W to 30 W Board-Mounted Power Modules (TN97-015EPS). Layout Considerations Copper paths must not be routed beneath the power module standoffs. From Figure 25, the 1/2 in. high heat sink or greater is required. 8 7 6 NO HEAT SINK 1/4 in. HEAT SINK 1/2 in. HEAT SINK 5 4 1 in. HEAT SINK 3 2 1 0 0 0.51 (100) 1.02 (200) 1.52 (300) AIR VELOCITY, ms 2.03 (400) -1 2.54 (500) 3.05 (600) (ft./min.) 8-1157(C).c Figure 25. Case-to-Ambient Thermal Resistance vs. Air Velocity Curves; Either Orientation Lineage Power 13 CC030-Series Power Modules; dc-dc Converters: 18 Vdc to 36 Vdc Inputs, 30 W Data Sheet March 2008 Outline Diagram Dimensions are in millimeters and (inches). Tolerances: x.x 0.5 mm (0.02 in.), x.xx 0.25 mm (0.010 in.) Note: For standard modules, VI(-) is internally connected to the case. Top View 71.1 (2.80) MAX +SEN ON/OFF TRIM Lucent 61.0 (2.40) MAX CASE PIN, OPTIONAL -SEN V I(+) V O(+) CC030B-M V I(-) DC-DC Power Module IN:DC 18-36V, 2.2A OUT:DC 12V, 2.5A V O(-) MADE IN USA M3 1676 Side View 0.51 (0.020) 12.7 (0.50) MAX 1.02 (0.040) DIA TIN-PLATED BRASS, 8 PLACES (9 PLACES WITH OPTIONAL CASE PIN) 5.1 (0.20) MIN STAND-OFF, 4 PLACES 4.8 (0.19) Bottom View 7.1 (0.28) CASE PIN, OPTIONAL 25.40 (1.000) V O(-) 10.16 (0.400) V I(-) V O(+) V I(+) 24.1 (0.95) 15.24 (0.600) ON/OFF MOUNTING INSERTS (-)SEN M3 x 0.5 THROUGH, TRIM 4 PLACES (+)SEN 17.78 (0.700) 7.62 (0.300) 50.8 (2.00) 5.08 (0.200) 20.32 (0.800) 12.70 (0.500) 5.1 (0.20) 48.3 (1.90) 11.4 (0.45) 63.50 0.38 (2.500 0.015) 3.8 (0.15) 8-1214(C).a 14 Lineage Power CC030-Series Power Modules; dc-dc Converters: 18 Vdc to 36 Vdc Inputs, 30 W Data Sheet March 2008 Recommended Hole Pattern Component-side footprint. Dimensions are in millimeters and (inches). M3 x 0.5 THROUGH CLEARANCE HOLE, 4 PLACES (OPTIONAL) CASE OUTLINE 5.1 (0.20) 24.1 (0.95) 61.0 (2.40) MAX 12.70 (0.500) 15.24 (0.600) 20.32 (0.800) 5.08 (0.200) 7.62 (0.300) 25.40 (1.000) 17.78 (0.700) 50.8 (2.00) 10.16 (0.400) CASE PIN, OPTIONAL 48.3 (1.90) 11.4 (0.45) 63.50 0.38 (2.500 0.015) 3.8 (0.15) 71.1 (2.80) MAX 8-1214(C).a Ordering Information For assistance with ordering options, contact your Lineage Power Account Manager or Field Application Engineer. Table 5. Device Codes Input Voltage Output Voltage Output Power Device Code Comcode 24 V 5V 30 W CC030A-M 107587172 24 V 12 V 30 W CC030B-M 107587180 24 V 15 V 30 W CC030C-M 107587198 Table 6. Device Options Option Comcode Short pins: 2.79 mm 0.25 mm (0.110 in. 0.010 in.) 8 Case ground pin 7 Negative Remote On/Off 1 Lineage Power 15 CC030-Series Power Modules; dc-dc Converters: 18 Vdc to 36 Vdc Inputs, 30 W Data Sheet March 2008 A sia-Pacific Head qu art ers T el: +65 6 41 6 4283 World W ide Headq u arters Lin eag e Po wer Co rp oratio n 30 00 Sk yline D riv e, Mesquite, T X 75149, U SA +1-800-526-7819 (Outs id e U .S.A .: +1- 97 2-2 84 -2626) www.line ag ep ower.co m e-m ail: tech sup port1@ lin ea gep ower.co m Eu ro pe, M id dle-East an d Afric a He ad qu arters T el: +49 8 9 6089 286 Ind ia Head qu arters T el: +91 8 0 28411633 Lineage Power reserves the right to make changes to the produc t(s) or information contained herein without notice. No liability is ass umed as a res ult of their use or applic ation. No rights under any patent acc ompany the sale of any s uc h pr oduct(s ) or information. (c) 2008 Lineage Power Corpor ation, (Mesquite, Texas ) All International Rights Res er ved. March 2008 DS98-225EPS (Replaces DS98-224EPS)