10-2014, Rev.1014
www.te.com
© 2014 Tyco Electronics Corporation,
a TE Connectivity Ltd. company
Datasheets and product specification
according to IEC 61810-1 and to be used
only together with the ‘Definitions’ section.
Datasheets and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Datasheets, product data, ‘Definitions’ sec-
tion, application notes and all specifications
are subject to change.
1
AXICOM
Signal Relays
n Standard telecom relay (ringing and test access)
n Slim line 15x7.5mm (.590x.295”)
n Max. switching current 5A
n 2 form C bifurcated contacts (2 changeover contacts, 2 CO)
n Immersion cleanable
n High sensitivity for low power consumption 140mW/ 70mW
n Single coil version with surge voltage resistance between contact
and coil: 2.5kV (2/10μs) meets the Telcordia Requirement GR-1089,
1.5kV (10/160μs) meets FCC Part 68
Typical applications
Communications equipment linecard application (ringing and test access),
PABX, voice over IP, office equipment, measurement and control equipment,
automotive equipment as CAN bus, keyless entry, speaker switch, medical
equipment, consumer electronics, set top boxes, HiFi
Approvals
UL 508 File No. E 111441, UL 60950,
IEC/EN60950 IEC Ref. Cert. No. 327
Technical data of approved types on request
Contact Data
Contact arrangement 2 form C (CO)
Max. switching voltage 220VDC, 250VAC
Rated current 2A
Limiting continuous current, 85°C 2A
Switching Power 60W, 62.5VA
Contact material AgNi, gold-covered
Contact style bifurcated contact
Minimum switching voltage 100μV
Thermoelectrical potential <10µV
Initial contact resistance <50mΩ at 10mA, 20mV
Frequency of operation, without load 50 operations/s
Operate time typ. 2ms, max. 4ms
Set/reset time typ. 2ms, max. 4ms
Release time
without diode in parallel typ. 2ms, max. 4ms
with diode in parallel typ. 4ms, max. 6ms
Bounce time typ. 1ms, max. 3ms
Electrical endurance
at 12V / 10mA typ. 5x107 operations
at 6V / 100mA typ. 1x107 operations
at 60V / 500mA typ. 5x105 operations
at 30V / 1000mA typ. 1x106 operations
at 30V / 2000mA typ. 2x105 operations
Contact ratings, UL 110VDC / 0.3A - 33W
30VDC / 2.0A - 60W
120VAC / 0.5A - 60VA
240VAC / 0.25A -60VA
Mechanical endurance typ. 100x106 operations
Coil Data
Magnetic system polarized
Coil voltage range 2 to 24VDC
Max. coil temperature 125°C
Thermal resistance < 125K/W
Coil versions, monostable
Coil Rated Operate Limiting Release Coil Rated coil
code voltage voltage Voltage voltage resistance power
VDC VDC VDC VDC Ω±10% mW
008 3.00 2.25 6.50 0.30 64 140
016 4.00 3.00 8.70 0.40 114 140
011 4.50 3.38 9.80 0.45 145 140
001 5.00 3.75 10.90 0.50 178 140
002 6.00 4.50 13.00 0.60 257 140
006 9.00 6.75 19.60 0.90 578 140
003 12.00 9.00 26.15 1.20 1029 140
005 24.00 18.00 52.30 2.40 4114 140
All figures are given for coil without pre-energization, at ambient temperature +23°C.
Other coil voltages on request.
P2 Relay V23079
DC current [A]
DC voltage [VDC]
Max. DC load breaking capacity
108-98002 Rev. E
All specifications subject to change. Consult Tyco Electronics for latest specifications. 5 of 15
Telecom-, Signal and RF Relays
P2 V23079 Relay
AXICOM
Coil Operating Range
Unom = Nominal coil voltage
Umax. = Upper limit of the operative range of
the coil voltage (limiting voltage) when coils are
continously energized
Uop. min. = Lower limit of the operative range of
the coil voltage (reliable operate voltage)
For latching relays Uset min. resp. Ureset min.
Urel. min. = Lower limit of the operative range of
the coil voltage (reliable release voltage)
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
-40-30 -20-10 0102030405060708090100 110 120 130 140
Coil Voltage [U/Unom]
Uop. min.
Umax. at 0 A
Umax. at 2 x 2 A
Umax. at 2 x 1 A
70 mW
Unom. nominal coil voltage
Ambient Temperature [°C]
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
2.2
2.4
2.6
2.8
-40-30 -20-10 0102030405060708090 100 110 120 130 140
Ambient Temperature [°C]
Coil Voltage [U/Unom]
140 mW
Umax. at 0 A
Umax. at 2 x 2 A
Umax. at 2 x 1 A
Unom. nominal coil voltage
Uop. min.
Urel. min.
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
2.2
2.4
2.6
2.8
-40-30 -20-10 0102030405060708090 100 110 120 130 140
Ambient Temperature [°C]
Coil Voltage [U/Unom]
200 mW
Umax. at 0 A
Umax. at 2 x 2 A
Umax. at 2 x 1 A
Unom. nominal coil voltage
Uop. min.
Urel. min.
Z
10-2014, Rev. 1014
www.te.com
© 2014 Tyco Electronics Corporation,
a TE Connectivity Ltd. company
Datasheets and product specification
according to IEC 61810-1 and to be used
only together with the ‘Definitions’ section.
Datasheets and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Datasheets, product data, ‘Definitions’ sec-
tion, application notes and all specifications
are subject to change.
2
AXICOM
Signal Relays
P2 Relay V23079 (Continued)
Insulation Data Standard HDV
Initial dielectric strength
between open contacts 1000Vrms 1500Vrms
between contact and coil 1500Vrms 1500Vrms
between adjacent contacts 1000 Vrms 1500Vrms
Initial surge withstand voltage
according to Telcordia TR-NWT-001089 (2/10μs)
between open contacts 2000V 2500V
between contact and coil 2500V 2500V
between adjacent contacts 2500V 2500V
according to (10/700 μs IEC 60950)
between open contacts 2000V 2500V
between contact and coil 2500V 2500V
between adjacent contacts 2500V 2500V
Initial insulation resistance at 500 Vdc > 109Ω
Capacitance
between open contacts max. 1pF
between contact and coil max. 2pF
between adjacent contacts max. 1.5pF
Clearance /creepage
according to IEC / EN 60950 1.3/2.5mm
Other Data
Material compliance: EU RoHS/ELV, China RoHS, REACH, Halogen content
refer to the Product Compliance Support Center at
www.te.com/customersupport/rohssupportcenter
Ambient temperature -40 to +85°C
Category of environmental protection
IEC 61810 RT III - wash tight
Degree of protection, IEC 60529 IP 67
Vibration resistance (functional) 35g, 10 to 1000Hz
Shock resistance (functional)
IEC 60068-2-27 (half sine) 100g
Terminal type PCB-THT,
SMT long and short terminals
Weight max. 2.8 g
Resistance to soldering heat THT
IEC 60068-2-20 265°C/10s
Moisture sensitive level, JEDEC J-Std-020D MSL3
related only to SMT relays
packed in orginal dry-packs
Ultrasonic cleaning not recommended
Packaging/unit
THT box/2000 pcs.
SMT reel/2000 pcs. or 2500 pcs.
Coil Data (continued)
Coil versions, bistable
Coil Rated Set Limiting Reset Coil Rated coil
code voltage voltage Voltage voltage resistance power
VDC VDC VDC VDC Ω±10% mW
Bistable, 1 coil
108 3.00 2.25 9.2 -2.25 128 70
111 4.50 3.38 13.85 -3.38 289 70
101 5.00 3.75 15.33 -3.75 357 70
102 6.00 4.50 18.5 -4.50 514 70
106 9.00 6.75 27.75 -6.75 1157 70
103 12.00 9.00 37 -9.00 2057 70
105 24.00 18.00 74 -18.00 8228 70
Bistable, 2 coil
219 2.00 1.50 4.33 1.50 28 140
218 2.40 1.80 5.2 1.80 41 140
208 3.00 2.25 6.5 2.25 64 140
211 4.50 3.38 9.8 3.38 145 140
201 5.00 3.75 10.9 3.75 178 140
202 6.00 4.50 13 4.50 257 140
206 9.00 6.75 19.6 6.75 578 140
203 12.00 9.00 26.15 9.00 1029 140
205 24.00 18.00 52.3 18.00 4114 140
All figures are given for coil without pre-energization, at ambient temperature +23°C.
Other coil voltages on request.
Coil versions, high dielectric version, monostable, overmolded
Coil Rated Operate Limiting Release Coil Rated coil
code voltage voltage Voltage Voltage resistance power
VDC VDC VDC VDC Ω±10% mW
008 3.00 2.25 6.1 0.30 45 200
001 5.00 3.75 10.1 0.50 125 200
002 6.00 4.50 12.1 0.60 180 200
006 9.00 6.75 18.2 0.90 405 200
003 12.00 9.00 24.2 1.20 720 200
All figures are given for coil without pre-energization, at ambient temperature +23°C.
Other coil voltages on request.
108-98002 Rev. E
All specifications subject to change. Consult Tyco Electronics for latest specifications. 5 of 15
Telecom-, Signal and RF Relays
P2 V23079 Relay
AXICOM
Coil Operating Range
Unom = Nominal coil voltage
Umax. = Upper limit of the operative range of
the coil voltage (limiting voltage) when coils are
continously energized
Uop. min. = Lower limit of the operative range of
the coil voltage (reliable operate voltage)
For latching relays Uset min. resp. Ureset min.
Urel. min. = Lower limit of the operative range of
the coil voltage (reliable release voltage)
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
-40-30 -20-10 0102030405060708090100 110 120 130 140
Coil Voltage [U/Unom]
Uop. min.
Umax. at 0 A
Umax. at 2 x 2 A
Umax. at 2 x 1 A
70 mW
Unom. nominal coil voltage
Ambient Temperature [°C]
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
2.2
2.4
2.6
2.8
-40-30 -20-10 0102030405060708090 100 110 120 130 140
Ambient Temperature [°C]
Coil Voltage [U/Unom]
140 mW
Umax. at 0 A
Umax. at 2 x 2 A
Umax. at 2 x 1 A
Unom. nominal coil voltage
Uop. min.
Urel. min.
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
2.2
2.4
2.6
2.8
-40-30 -20-10 0102030405060708090 100 110 120 130 140
Ambient Temperature [°C]
Coil Voltage [U/Unom]
200 mW
Umax. at 0 A
Umax. at 2 x 2 A
Umax. at 2 x 1 A
Unom. nominal coil voltage
Uop. min.
Urel. min.
108-98002 Rev. E
All specifications subject to change. Consult Tyco Electronics for latest specifications. 5 of 15
Telecom-, Signal and RF Relays
P2 V23079 Relay
AXICOM
Coil Operating Range
Unom = Nominal coil voltage
Umax. = Upper limit of the operative range of
the coil voltage (limiting voltage) when coils are
continously energized
Uop. min. = Lower limit of the operative range of
the coil voltage (reliable operate voltage)
For latching relays Uset min. resp. Ureset min.
Urel. min. = Lower limit of the operative range of
the coil voltage (reliable release voltage)
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
2.2
2.4
2.6
2.8
3
3.2
3.4
-40-30 -20-10 0102030405060708090100 110 120 130 140
Coil Voltage [U/Unom]
Uop. min.
Umax. at 0 A
Umax. at 2 x 2 A
Umax. at 2 x 1 A
70 mW
Unom. nominal coil voltage
Ambient Temperature [°C]
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
2.2
2.4
2.6
2.8
-40-30 -20-10 0102030405060708090 100 110 120 130 140
Ambient Temperature [°C]
Coil Voltage [U/Unom]
140 mW
Umax. at 0 A
Umax. at 2 x 2 A
Umax. at 2 x 1 A
Unom. nominal coil voltage
Uop. min.
Urel. min.
0
0.2
0.4
0.6
0.8
1
1.2
1.4
1.6
1.8
2
2.2
2.4
2.6
2.8
-40-30 -20-10 0102030405060708090 100 110 120 130 140
Ambient Temperature [°C]
Coil Voltage [U/Unom]
200 mW
Umax. at 0 A
Umax. at 2 x 2 A
Umax. at 2 x 1 A
Unom. nominal coil voltage
Uop. min.
Urel. min.
10-2014, Rev.1014
www.te.com
© 2014 Tyco Electronics Corporation,
a TE Connectivity Ltd. company
Datasheets and product specification
according to IEC 61810-1 and to be used
only together with the ‘Definitions’ section.
Datasheets and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Datasheets, product data, ‘Definitions’ sec-
tion, application notes and all specifications
are subject to change.
3
AXICOM
Signal Relays
P2 Relay V23079 (Continued)
PCB layout
TOP view on component side of PCB
THT version SMT, long terminals SMT, short terminals
0,9 ±0,1
Contacts are shown in reset
condition.
Both coils can be used as
either set or reset coils.
Contact position might change
during transportation and must
be reset before use.
Monostable version
Terminal assignment
TOP view on component side of PCB
Bistable version, 1-coil Bistable version, 2-coils
Dimensions
0.5±0.05
10.4±0.15
14.5±0.1 7.2±0.1
0.5±0.05
9.8±0.1
3.25-0.25
0.55-0.15
5.52±0.15
9.4±0.15
14.5±0.1 7.2±0.1
0.5±0.05
10.4±0.15
5.52
7.4±0.15
14.5±0.1 7.2±0.1
0.5±0.05
9.9±0.1
14.6±0.1 7.2±0.1
0.5±0.05
9.5±0.1
3.25-0.25
0.45
5.52
9.4±0.15
14.6±0.1 7.2±0.1
0.5±0.05
9.9±0.15
5.52
7.4±0.15
14.6±0.1 7.2±0.1
THT version SMT, long terminals SMT, short terminals
Standard coil
0.5±0.05
10.4±0.15
14.5±0.1 7.2±0.1
0.5±0.05
9.8±0.1
3.25-0.25
0.55-0.15
5.52±0.15
9.4±0.15
14.5±0.1 7.2±0.1
0.5±0.05
10.4±0.15
5.52
7.4±0.15
14.5±0.1 7.2±0.1
0.5±0.05
9.9±0.1
14.6±0.1 7.2±0.1
0.5±0.05
9.5±0.1
3.25-0.25
0.45
5.52
9.4±0.15
14.6±0.1 7.2±0.1
0.5±0.05
9.9±0.15
5.52
7.4±0.15
14.6±0.1 7.2±0.1
0.5±0.05
10.4±0.15
14.5±0.1 7.2±0.1
0.5±0.05
9.8±0.1
3.25-0.25
0.55-0.15
5.52±0.15
9.4±0.15
14.5±0.1 7.2±0.1
0.5±0.05
10.4±0.15
5.52
7.4±0.15
14.5±0.1 7.2±0.1
0.5±0.05
9.9±0.1
14.6±0.1 7.2±0.1
0.5±0.05
9.5±0.1
3.25-0.25
0.45
5.52
9.4±0.15
14.6±0.1 7.2±0.1
0.5±0.05
9.9±0.15
5.52
7.4±0.15
14.6±0.1 7.2±0.1
0.5±0.05
10.4±0.15
14.5±0.1 7.2±0.1
0.5±0.05
9.8±0.1
3.25-0.25
0.55-0.15
5.52±0.15
9.4±0.15
14.5±0.1 7.2±0.1
0.5±0.05
10.4±0.15
5.52
7.4±0.15
14.5±0.1 7.2±0.1
0.5±0.05
9.9±0.1
14.6±0.1 7.2±0.1
0.5±0.05
9.5±0.1
3.25-0.25
0.45
5.52
9.4±0.15
14.6±0.1 7.2±0.1
0.5±0.05
9.9±0.15
5.52
7.4±0.15
14.6±0.1 7.2±0.1
THT version SMT, long terminals SMT, short terminals
Overmolded coil, high dielectric version
0.5±0.05
10.4±0.15
14.5±0.1 7.2±0.1
0.5±0.05
9.8±0.1
3.25-0.25
0.55-0.15
5.52±0.15
9.4±0.15
14.5±0.1 7.2±0.1
0.5±0.05
10.4±0.15
5.52
7.4±0.15
14.5±0.1 7.2±0.1
0.5±0.05
9.9±0.1
14.6±0.1 7.2±0.1
0.5±0.05
9.5±0.1
3.25-0.25
0.45
5.52
9.4±0.15
14.6±0.1 7.2±0.1
0.5±0.05
9.9±0.15
5.52
7.4±0.15
14.6±0.1 7.2±0.1
0.5±0.05
10.4±0.15
14.5±0.1 7.2±0.1
0.5±0.05
9.8±0.1
3.25-0.25
0.55-0.15
5.52±0.15
9.4±0.15
14.5±0.1 7.2±0.1
0.5±0.05
10.4±0.15
5.52
7.4±0.15
14.5±0.1 7.2±0.1
0.5±0.05
9.9±0.1
14.6±0.1 7.2±0.1
0.5±0.05
9.5±0.1
3.25-0.25
0.45
5.52
9.4±0.15
14.6±0.1 7.2±0.1
0.5±0.05
9.9±0.15
5.52
7.4±0.15
14.6±0.1 7.2±0.1
10-2014, Rev. 1014
www.te.com
© 2014 Tyco Electronics Corporation,
a TE Connectivity Ltd. company
Datasheets and product specification
according to IEC 61810-1 and to be used
only together with the ‘Definitions’ section.
Datasheets and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Datasheets, product data, ‘Definitions’ sec-
tion, application notes and all specifications
are subject to change.
4
AXICOM
Signal Relays
P2 Relay V23079 (Continued)
Processing
full line: typical
dotted line: process limits
external preheating
240°C
180°C
130°C
100°C
forced cooling
20 to 40s
Time [s]
Temperature [°C]
Vapour phase soldering
temperature/time profile
(lead and housing peak temp.)
Recommended soldering conditions
Vapour phase soldering
Time [s]
Temperature [°C]
Recommended reflow soldering profile
Infrared soldering
temperature/time profile
(lead and housing peak temp.)
Reel dimensions
Packing
10-2014, Rev.1014
www.te.com
© 2014 Tyco Electronics Corporation,
a TE Connectivity Ltd. company
Datasheets and product specification
according to IEC 61810-1 and to be used
only together with the ‘Definitions’ section.
Datasheets and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Datasheets, product data, ‘Definitions’ sec-
tion, application notes and all specifications
are subject to change.
5
AXICOM
12
15.5
9
10.4 0.4
16
12
15.5
9
10.4 0.4
NEW
THIS DRAWING IS A CONTROLLED DOCUMENT
1 PLC
0 PLC
2 PLC
3 PLC
4 PLC
DIMENSIONS: TOLERANCES UNLESS
OTHERWISE SPECIFIED:
USED ON
P LTR APVDDATEREVISION RECORD DWN
DWG NO
SIZE
OF
C
1
23456
7
8
A
B
DRAWING NO
LOC
DIST
D
SHEET REV
APVD
DWN
CHK
NAME
SCALE
MATERIAL HEAT TREAT
ANGLES
SURFACE TEXTURE
3306-7 (3/11)
A3
THIS INFORMATION IS CONFIDENTIAL AND PROPRIETARY TO TYCO
ELECTRONICS CORPORATION AND ITS WORLDWIDE SUBSIDIARIES
AND AFFILIATES (TE). IT MAY NOT BE DISCLOSED TO ANYONE,
OTHER THAN TE PERSONNEL, WITHOUT
AUTHORIZATION FROM TE (www.TE.com).
TE Connectivity
B
B
A
A
24±0.3
PS conductivity 10
B-B
2:1
2:1
1.2+0.2
0
11.5±0.1
max. 3°
1.75±0.1
4±0.1
1.9±0.2
(3.6)
max. R
0.3
(3.6)
1.9±0.2
4.4±0.2
2.2±0.2
1.3±0.2
max. 3°
4±0.2
10.4+0.3
0
10±0.2
12±0.2
15.4±0.2
16±0.15
(8)
1.5 0.1
2±0.1
1.5 0.1
0.6
12.2±0.2
( 1.5)
(48)
max. R0.3
max. 3°
max. 3°
1.5
1.5
-9 S/m
roztec transportnich otvoru
distance of transport holes
4x10=40±0.2mm
4x11=44±0.2mm
4x12=48±0.2mm
A-A
-
C23303-A079-C121
30.3.2012
-
Zdenek Curda
-
-
-
mm 30.3.2012
-
0.1 Petr Hofman
0.01
-0.001
0.0001 P2L3 - Blister tape long terminals
-
-
-4:1 C23303-A079-C121 1 1 3
3-
30.03.2012
ZC PH
2-
17.06.2011
PH 9122
1-
25.05.1998
PH 9122
THIS DRAWING IS A CONTROLLED DOCUMENT
1 PLC
0 PLC
2 PLC
3 PLC
4 PLC
DIMENSIONS: TOLERANCES UNLESS
OTHERWISE SPECIFIED:
USED ON
P LTR APVDDATEREVISION RECORD DWN
DWG NO
SIZE
OF
C
1
23456
7
8
A
B
DRAWING NO
LOC
DIST
D
SHEET REV
APVD
DWN
CHK
NAME
SCALE
MATERIAL HEAT TREAT
ANGLES
SURFACE TEXTURE
3306-7 (3/11)
A3
THIS INFORMATION IS CONFIDENTIAL AND PROPRIETARY TO TYCO
ELECTRONICS CORPORATION AND ITS WORLDWIDE SUBSIDIARIES
AND AFFILIATES (TE). IT MAY NOT BE DISCLOSED TO ANYONE,
OTHER THAN TE PERSONNEL, WITHOUT
AUTHORIZATION FROM TE (www.TE.com).
TE Connectivity
B
B
A
A
24±0.3
PS conductivity 10
B-B
2:1
2:1
1.2+0.2
0
11.5±0.1
max. 3°
1.75±0.1
4±0.1
1.9±0.2
(3.6)
max. R0.3
(3.6)
1.9±0.2
4.4±0.2
2.2±0.2
1.3±0.2
max. 3°
4±0.2
10.4
+0.3
0
10±0.2
12±0.2
15.4±0.2
16±0.15
(8)
1.5 0.1
2±0.1
1.5 0.1
0.6
12.2±0.2
( 1.5)
(48)
max. R0.3
max.
3°
max. 3°
1.5
1.5
-9 S/m
roztec transportnich otvoru
distance of transport holes
4x10=40±0.2mm
4x11=44±0.2mm
4x12=48±0.2mm
A-A
-
C23303-A079-C121
30.3.2012 -
Zdenek Curda -
-
-
mm 30.3.2012
-
0.1 Petr Hofman
0.01
-0.001
0.0001 P2L3 - Blister tape long terminals
-
-
-4:1 C23303-A079-C121 1 1 3
3-
30.03.2012
ZC PH
2-
17.06.2011
PH 9122
1-
25.05.1998
PH 9122
THIS DRAWING IS A CONTROLLED DOCUMENT
1 PLC
0 PLC
2 PLC
3 PLC
4 PLC
DIMENSIONS: TOLERANCES UNLESS
OTHERWISE SPECIFIED:
USED ON
P LTR APVDDATEREVISION RECORD DWN
DWG NO
SIZE
OF
C
1
23456
7
8
A
B
DRAWING NO
LOC
DIST
D
SHEET REV
APVD
DWN
CHK
NAME
SCALE
MATERIAL HEAT TREAT
ANGLES
SURFACE TEXTURE
3306-7 (3/11)
A3
THIS INFORMATION IS CONFIDENTIAL AND PROPRIETARY TO TYCO
ELECTRONICS CORPORATION AND ITS WORLDWIDE SUBSIDIARIES
AND AFFILIATES (TE). IT MAY NOT BE DISCLOSED TO ANYONE,
OTHER THAN TE PERSONNEL, WITHOUT
AUTHORIZATION FROM TE (www.TE.com).
TE Connectivity
B
B
A
A
24±0.3
PS conductivity 10
B-B
2:1
2:1
1.2+0.2
0
11.5±0.1
max.
3°
1.75±0.1
4±0.1
1.9±0.2
(3.6)
max. R0.3
(3.6)
1.9±0.2
4.4±0.2
2.2±0.2
1.3±0.2
max. 3°
4±0.2
10.4
+0.3
0
10±0.2
12±0.2
15.4±0.2
16±0.15
(8)
1.5 0.1
2±0.1
1.5 0.1
0.6
12.2±0.2
( 1.5)
(48)
max. R0.3
max. 3°
max. 3°
1.5
1.5
-9 S/m
roztec transportnich otvoru
distance of transport holes
4x10=40±0.2mm
4x11=44±0.2mm
4x12=48±0.2mm
A-A
-
C23303-A079-C121
30.3.2012 -
Zdenek Curda -
-
-
mm 30.3.2012
-
0.1 Petr Hofman
0.01
-0.001
0.0001 P2L3 - Blister tape long terminals
-
-
-4:1 C23303-A079-C121 1 1 3
3-
30.03.2012
ZC PH
2-
17.06.2011
PH 9122
1-
25.05.1998
PH 9122
THIS DRAWING IS A CONTROLLED DOCUMENT
1 PLC
0 PLC
2 PLC
3 PLC
4 PLC
DIMENSIONS: TOLERANCES UNLESS
OTHERWISE SPECIFIED:
USED ON
P LTR APVDDATEREVISION RECORD DWN
DWG NO
SIZE
OF
C
1
23456
7
8
A
B
DRAWING NO
LOC
DIST
D
SHEET REV
APVD
DWN
CHK
NAME
SCALE
MATERIAL HEAT TREAT
ANGLES
SURFACE TEXTURE
3306-7 (3/11)
A3
THIS INFORMATION IS CONFIDENTIAL AND PROPRIETARY TO TYCO
ELECTRONICS CORPORATION AND ITS WORLDWIDE SUBSIDIARIES
AND AFFILIATES (TE). IT MAY NOT BE DISCLOSED TO ANYONE,
OTHER THAN TE PERSONNEL, WITHOUT
AUTHORIZATION FROM TE (www.TE.com).
TE Connectivity
A
A
B
B
24±0.3
0.6
PS conductivity 10
B-B
2:1
2:1
1.2+0.2
0
11.5±0.1
12±0.15
1.75±0.1
4±0.1 2±0.1
1.5 0.1
10.9
+0.3
0
4±0.2
max. R0.3
max. 3°
1.5 0.1
8±0.2
9±0.2
max. R0.3
9.1±0.2
1.3±0.2
2.2±0.2
15.4±0.2
max. 3°
(3.6)
(3.6)
1.9±0.2
1.9±0.2
4.5±0.2
max. 3°
max. 3°
1.5
1.5
-9 S/m
roztec transportnich otvoru
distance of transport holes
4x10=40±0.2mm
4x11=44±0.2mm
4x12=48±0.2mm
A-A
-
C23303-A079-C120
26.3.2012 -
Zdenek Curda -
-
-
mm 26.3.2012
-
0.1 Petr Hofman
0.01
-0.001
0.0001 P2L2/P2L3/FU2 - Blister tape short terminals
-
-
-4:1 C23303-A079-C120 1 1 8
8-
26.3.2012
ZC PH
7-
13.12.2005
9193 9121
1-
25.05.1998
9188 9151
THIS DRAWING IS A CONTROLLED DOCUMENT
1 PLC
0 PLC
2 PLC
3 PLC
4 PLC
DIMENSIONS: TOLERANCES UNLESS
OTHERWISE SPECIFIED:
USED ON
P LTR APVDDATEREVISION RECORD DWN
DWG NO
SIZE
OF
C
1
23456
7
8
A
B
DRAWING NO
LOC
DIST
D
SHEET REV
APVD
DWN
CHK
NAME
SCALE
MATERIAL HEAT TREAT
ANGLES
SURFACE TEXTURE
3306-7 (3/11)
A3
THIS INFORMATION IS CONFIDENTIAL AND PROPRIETARY TO TYCO
ELECTRONICS CORPORATION AND ITS WORLDWIDE SUBSIDIARIES
AND AFFILIATES (TE). IT MAY NOT BE DISCLOSED TO ANYONE,
OTHER THAN TE PERSONNEL, WITHOUT
AUTHORIZATION FROM TE (www.TE.com).
TE Connectivity
A
A
B
B
24±0.3
0.6
PS conductivity 10
B-B
2:1
2:1
1.2+0.2
0
11.5±0.1
12±0.15
1.75±0.1
4±0.1 2±0.1
1.5 0.1
10.9
+0.3
0
4±0.2
max. R0.3
max. 3°
1.5 0.1
8±0.2
9±0.2
max. R0.3
9.1±0.2
1.3±0.2
2.2±0.2
15.4±0.2
max. 3°
(3.6)
(3.6)
1.9±0.2
1.9±0.2
4.5±0.2
max. 3°
max. 3°
1.5
1.5
-9 S/m
roztec transportnich otvoru
distance of transport holes
4x10=40±0.2mm
4x11=44±0.2mm
4x12=48±0.2mm
A-A
-
C23303-A079-C120
26.3.2012 -
Zdenek Curda -
-
-
mm 26.3.2012
-
0.1 Petr Hofman
0.01
-0.001
0.0001 P2L2/P2L3/FU2 - Blister tape short terminals
-
-
-4:1 C23303-A079-C120 1 1 8
8-
26.3.2012
ZC PH
7-
13.12.2005
9193 9121
1-
25.05.1998
9188 9151
THIS DRAWING IS A CONTROLLED DOCUMENT
1 PLC
0 PLC
2 PLC
3 PLC
4 PLC
DIMENSIONS: TOLERANCES UNLESS
OTHERWISE SPECIFIED:
USED ON
P LTR APVDDATEREVISION RECORD DWN
DWG NO
SIZE
OF
C
1
23456
7
8
A
B
DRAWING NO
LOC
DIST
D
SHEET REV
APVD
DWN
CHK
NAME
SCALE
MATERIAL HEAT TREAT
ANGLES
SURFACE TEXTURE
3306-7 (3/11)
A3
THIS INFORMATION IS CONFIDENTIAL AND PROPRIETARY TO TYCO
ELECTRONICS CORPORATION AND ITS WORLDWIDE SUBSIDIARIES
AND AFFILIATES (TE). IT MAY NOT BE DISCLOSED TO ANYONE,
OTHER THAN TE PERSONNEL, WITHOUT
AUTHORIZATION FROM TE (www.TE.com).
TE Connectivity
A
A
B
B
24±0.3
0.6
PS conductivity 10
B-B
2:1
2:1
1.2+0.2
0
11.5±0.1
12±0.15
1.75±0.1
4±0.1 2±0.1
1.5 0.1
10.9
+0.3
0
4±0.2
max. R0.3
max. 3°
1.5 0.1
8±0.2
9±0.2
max. R0.3
9.1±0.2
1.3±0.2
2.2±0.2
15.4±0.2
max. 3°
(3.6)
(3.6)
1.9±0.2
1.9±0.2
4.5±0.2
max. 3°
max. 3°
1.5
1.5
-9 S/m
roztec transportnich otvoru
distance of transport holes
4x10=40±0.2mm
4x11=44±0.2mm
4x12=48±0.2mm
A-A
-
C23303-A079-C120
26.3.2012 -
Zdenek Curda -
-
-
mm 26.3.2012
-
0.1 Petr Hofman
0.01
-0.001
0.0001 P2L2/P2L3/FU2 - Blister tape short terminals
-
-
-4:1 C23303-A079-C120 1 1 8
8-
26.3.2012
ZC PH
7-
13.12.2005
9193 9121
1-
25.05.1998
9188 9151
Tape and reel for SMT
16
10.4 0.4
16
10.4 0.4
12
15.5
9
10.4 0.4
NEW
NEW
Signal Relays
P2 Relay V23079 (Continued)
10-2014, Rev. 1014
www.te.com
© 2014 Tyco Electronics Corporation,
a TE Connectivity Ltd. company
Datasheets and product specification
according to IEC 61810-1 and to be used
only together with the ‘Definitions’ section.
Datasheets and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Datasheets, product data, ‘Definitions’ sec-
tion, application notes and all specifications
are subject to change.
6
AXICOM
Signal Relays
P2 Relay V23079 (Continued)
Product code structure Typical product code V23079 A 1 001 B 301
Type
V23079 Signal Relay P2 Series
Version
A THT, monostable D SMT, monostable, long term. G SMT, monostable, short term.
B THT, latching, 2 coils E SMT, latching, 2 coils long term. H SMT, latching, 2 coils short term.
C THT, latching, 1 coil F SMT, latching, 1 coil long term. J SMT, latching, 1 coil short term.
Coil design
1 Standard coil (not for high dielectric version)
2 Overmolded coil
Coil
Coil code: please refer to coil versions table
Version
B Standard version
X High dielectric version
Contacts for standard versions
301 2 form C contacts (2 CO), AgNi +Au
201 2 form C contacts (2 CO), AgPd +Au; on request only
Product code Version Coil design Coil type Coil voltage Part number
V23079-A1006-B301 9VDC 2-1393788-0
V23079-A1005-B301 24VDC 1-1393788-6
V23079-A2008-B301 Overmolded 3VDC 6-1419120-6
V23079-A2011-B301 4.5VDC 3-1393789-9
V23079-A2001-B301 5VDC 3-1393789-5
V23079-A2002-B301 6VDC 3-1393789-6
V23079-A2006-B301 9VDC 3-1393789-8
V23079-A2003-B301 12VDC 3-1393789-7
V23079-B1218-B301 Standard Bistable, 2 coils 2.4VDC 1422002-8
V23079-B1208-B301 3VDC 4-1393788-1
V23079-B1211-B301 4.5VDC 4-1393788-2
V23079-B1201-B301 5VDC 3-1393788-3
V23079-B1202-B301 6VDC 3-1393788-5
V23079-B1206-B301 9VDC 3-1393788-9
V23079-B1203-B301 12VDC 3-1393788-6
V23079-B1205-B301 24VDC 3-1393788-7
V23079-B2219-B301 Overmolded 2VDC 1-1422002-2
V23079-B2218-B301 2.4VDC 1-1422002-1
V23079-B2208-B301 3VDC 1-1422002-0
V23079-B2201-B301 5VDC 1422002-9
V23079-C1108-B301 Standard Bistable, 1 coils 3VDC 5-1393788-3
V23079-C1111-B301 4.5VDC 5-1393788-4
V23079-C1101-B301 5VDC 4-1393788-5
V23079-C1102-B301 6VDC 4-1393788-7
V23079-C1106-B301 9VDC 5-1393788-1
V23079-C1103-B301 12VDC 4-1393788-8
V23079-C1105-B301 24VDC 5-1393788-0
10-2014, Rev.1014
www.te.com
© 2014 Tyco Electronics Corporation,
a TE Connectivity Ltd. company
Datasheets and product specification
according to IEC 61810-1 and to be used
only together with the ‘Definitions’ section.
Datasheets and product data is subject to the
terms of the disclaimer and all chapters of
the ‘Definitions’ section, available at
http://relays.te.com/definitions
Datasheets, product data, ‘Definitions’ sec-
tion, application notes and all specifications
are subject to change.
7
AXICOM
Signal Relays
P2 Relay V23079 (Continued)
Product code Version Coil design Coil type Coil voltage Part number
V23079-D1006-B301 9VDC 5-1393788-9
V23079-D1005-B301 24VDC 5-1393788-8
V23079-D2008-B301 Overmolded 3VDC 4-1393789-7
V23079-D2011-B301 4.5VDC 4-1393789-8
V23079-D2001-B301 5VDC 4-1393789-3
V23079-D2002-B301 6VDC 4-1393789-4
V23079-D2006-B301 9VDC 4-1393789-6
V23079-D2003-B301 12VDC 4-1393789-5
V23079-E1219-B301 Standard Bistable, 2 coils 2VDC 1-1422007-0
V23079-E1218-B301 2.4VDC 1422007-5
V23079-E1208-B301 3VDC 7-1393788-1
V23079-E1211-B301 4.5VDC 7-1393788-2
V23079-E1201-B301 5VDC 6-1393788-8
V23079-E1202-B301 6VDC 1393789-5
V23079-E1206-B301 9VDC 1393789-9
V23079-E1203-B301 12VDC 6-1393788-9
V23079-E1205-B301 24VDC 7-1393788-0
V23079-E2219-B301 Overmolded 2VDC 1422007-6
V23079-E2201-B301 5VDC 1422007-7
V23079-E2208-B301 3VDC 1422007-8
V23079-E2218-B301 2.4VDC 1422007-9
V23079-F1108-B301 Standard Bistable, 1 coil 3VDC 7-1393788-5
V23079-F1111-B301 4.5VDC 1-1393789-4
V23079-F1101-B301 5VDC 7-1393788-3
V23079-F1102-B301 6VDC 1-1393789-0
V23079-F1106-B301 9VDC 1-1393789-2
V23079-F1103-B301 12VDC 7-1393788-4
V23079-F1105-B301 24VDC 1-1393789-1
V23079-G1005-B301 SMT, short pins Monostable 24VDC 7-1393788-8
V23079-G2008-B301 Overmolded 3VDC 5-1393789-4
V23079-G2016-B301 4VDC 1393790-5
V23079-G2011-B301 4.5VDC 5-1393789-5
V23079-G2001-B301 5VDC 4-1393789-9
V23079-G2002-B301 6VDC 5-1393789-0
V23079-G2006-B301 9VDC 5-1393789-3
V23079-G2003-B301 12VDC 5-1393789-1
V23079-H1208-B301 Standard Bistable, 2 coils 3VDC 2-1393789-4
V23079-H1211-B301 4.5VDC 8-1393788-4
V23079-H1201-B301 5VDC 2-1393789-0
V23079-H1202-B301 6VDC 2-1393789-1
V23079-H1206-B301 9VDC 2-1393789-3
V23079-H1203-B301 12VDC 8-1393788-3
V23079-H1205-B301 24VDC 2-1393789-2
V23079-J1108-B301 Bistable, 1 coil 3VDC 2-1393789-9
V23079-J1111-B301 4.5VDC 3-1393789-0
V23079-J1101-B301 5VDC 2-1393789-5
V23079-J1102-B301 6VDC 2-1393789-6
V23079-J1103-B301 12VDC 2-1393789-7
V23079-J1105-B301 24VDC 2-1393789-8
V23079-G2008-X079 High dielectric Monostable 3VDC 1422006-5
V23079-G2001-X071 Overmolded 5VDC 1422006-1
V23079-G2002-X072 6VDC 1422006-2
V23079-G2006-X073 9VDC 1422006-3
V23079-G2003-X074 12VDC 1422006-4
V23079-A2003-X074 12VDC 1422025-7
V23079-A2008-X079 3VDC 1-1422025-1