ADS800 A DS 800 U SBAS035B - FEBRUARY 1995 - REVISED FEBRUARY 2005 12-Bit, 40MHz Sampling ANALOG-TO-DIGITAL CONVERTER FEATURES DESCRIPTION The ADS800 is a low-power, monolithic 12-bit, 40MHz Analog-to-Digital (A/D) converter utilizing a small geometry CMOS process. This complete converter includes a 12-bit quantizer, wideband track-and-hold, reference, and three-state outputs. It operates from a single +5V power supply and can be configured to accept either differential or single-ended input signals. LOW POWER: 390mW INTERNAL REFERENCE WIDEBAND TRACK-AND-HOLD: 65MHz SINGLE +5V SUPPLY APPLICATIONS The ADS800 employs digital error correction to provide excellent Nyquist differential linearity performance for demanding imaging applications. Its low distortion, high SNR, and high oversampling capability give it the extra margin needed for telecommunications, test instrumentation, and video applications. IF AND BASEBAND DIGITIZATION DIGITAL COMMUNICATIONS ULTRASOUND IMAGING GAMMA CAMERAS TEST INSTRUMENTATION CCD IMAGING Copiers Scanners Cameras VIDEO DIGITIZING This high-performance A/D converter is specified over temperature for AC and DC performance at a 40MHz sampling rate. The ADS800 is available in an SO-28 package. CLK MSBI OE Error Correction Logic 3-State Outputs Timing Circuitry IN Pipeline A/D Converter T/H IN 12-Bit Digital Data +3.25V REFT CM REFB +1.25V Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. Copyright (c) 1995-2005, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. www.ti.com ELECTROSTATIC DISCHARGE SENSITIVITY ABSOLUTE MAXIMUM RATINGS(1) +VS ....................................................................................................... +6V Analog Input .............................................................. 0V to (+VS + 300mV) Logic Input ................................................................ 0V to (+VS + 300mV) Case Temperature ......................................................................... +100C Junction Temperature .................................................................... +150C Storage Temperature ..................................................................... +125C External Top Reference Voltage (REFT) .................................. +3.4V Max External Bottom Reference Voltage (REFB) .............................. +1.1V Min This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet its published specifications. NOTE: (1) Stresses above these ratings may permanently damage the device. PACKAGE/ORDERING INFORMATION(1) PRODUCT PACKAGE-LEAD PACKAGE DESIGNATOR ADS800U SO-28 DW SPECIFIED TEMPERATURE RANGE PACKAGE MARKING ORDERING NUMBER TRANSPORT MEDIA, QUANTITY -40C to +85C ADS800U ADS800U Rails, 28 NOTE: (1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI website at www.ti.com. ELECTRICAL CHARACTERISTICS At TA = +25C, VS = +5V, Sampling Rate = 40MHz, and with a 50% duty cycle clock having a 2ns rise-and-fall time, unless otherwise noted. ADS800U PARAMETER Resolution Specified Temperature Range Operating Temperature Range ANALOG INPUT Differential Full-Scale Input Range Common-Mode Voltage Analog Input Bandwidth (-3dB) Small-Signal Full-Power Input Impedance DIGITAL INPUT Logic Family Convert Command CONDITIONS f = 12MHz (-1dBFS input) MAX UNITS 0 -40 +70 +85 Bits C C Both Inputs, 180 Out-of-Phase +1.25 +3.25 V -20dBFS(1) Input 0dBFS Input +25C +25C fS = 2.5MHz +25C Full +VS = 5% +VS = 5% +2.25 V 400 65 1.25 || 4 MHz MHz M || pF TTL/HCT Compatible CMOS Falling Edge Start Conversion 0.4 0.6 95 0.01 2.6 0.02 +25C Full +25C 10k 1.5 2.5 0.15 3.5 0.15 tH = 13ns(3) tH = 13ns(3) 0.6 0.8 0.4 0.5 Tested 1.9 +25C Full +25C Full +25C Full +25C Full +25C Full 65 60 58 55 72 66 61 61 % % ppm/C %FSR/% % %FSR/% 40M Sample/s Convert Cycle 1.0 LSB LSB LSB LSB LSB LSB 6.5 f = 12MHz No Missing Codes Integral Linearity Error at f = 500kHz Spurious-Free Dynamic Range (SFDR) f = 500kHz (-1dBFS input) TYP TAMBIENT TAMBIENT CONVERSION CHARACTERISTICS Sample Rate Data Latency DYNAMIC CHARACTERISTICS Differential Linearity Error f = 500kHz MIN 12 ACCURACY(2) Gain Error Gain Drift Power-Supply Rejection of Gain Input Offset Error Power-Supply Rejection of Offset TEMP 1.0 dBFS dBFS dBFS dBFS NOTES: (1) dBFS refers to dB below Full-Scale. (2) Percentage accuracies are referred to the internal A/D converter Full-Scale Range of 4Vp-p. (3) To assure DNL and no missing code performance, see timing diagram footnote 2. (4) IMD is referred to the larger of the two input signals. If referred to the peak envelope signal (0dB), the intermodulation products will be 7dB lower. (5) No "rollover" of bits. 2 ADS800 www.ti.com SBAS035B ELECTRICAL CHARACTERISTICS (Cont.) At TA = +25C, VS = +5V, Sampling Rate = 40MHz, and with a 50% duty cycle clock having a 2ns rise-and-fall time, unless otherwise noted. ADS800U PARAMETER CONDITIONS DYNAMIC CHARACTERISTICS (Cont.) 2-Tone Intermodulation Distortion (IMD)(4) f = 4.4MHz and 4.5MHz (-7dBFS each tone) f = 12MHz (-1dBFS input) Signal-to-(Noise + Distortion) (SINAD) f = 500kHz (-1dBFS input) f = 12MHz (-1dBFS input) OUTPUTS Logic Family Logic Coding Logic Levels NTSC or PAL NTSC or PAL 1.5x Full-Scale Input Logic "LO", CL = 15pF max Logic "HI", CL = 15pF max 3-State Enable Time 3-State Disable Time POWER-SUPPLY REQUIREMENTS Supply Voltage: +VS Supply Current: +IS Power Consumption MIN +25C Full Signal-to-Noise Ratio (SNR) f = 500kHz (-1dBFS input) Differential Gain Error Differential Phase Error Aperture Delay Time Aperture Jitter Over-Voltage Recovery Time(5) TEMP MAX UNITS -63 -62 dBc dBc +25C Full +25C Full 61 57 61 56 64 63 62 62 dB dB dB dB +25C Full +25C Full +25C +25C +25C +25C +25C 59 54 56 51 63 64 58 57 0.5 0.1 2 7 2 dB dB dB dB % degrees ns ps rms ns TTL/HCT Compatible CMOS SOB or BTC 0 0.4 V Logic Selectable Full Full +2.5 Full Operating Operating Operating Operating Operating TYP Full +25C Full +25C Full Thermal Resistance, JA SO-28 +4.75 +VS V 20 2 40 10 ns ns +5.0 78 78 390 390 +5.25 93 97 465 485 V mA mA mW mW 75 C/W NOTES: (1) dBFS refers to dB below Full-Scale. (2) Percentage accuracies are referred to the internal A/D converter Full-Scale Range of 4Vp-p. (3) To assure DNL and no missing code performance, see timing diagram footnote 2. (4) IMD is referred to the larger of the two input signals. If referred to the peak envelope signal (0dB), the intermodulation products will be 7dB lower. (5) No "rollover" of bits. ADS800 SBAS035B www.ti.com 3 PIN CONFIGURATION PIN DESCRIPTIONS Top View SO GND 1 28 GND B1 2 27 IN B2 3 26 IN B3 4 25 GND B4 5 24 +VS B5 6 23 REFT B6 7 22 CM ADS800 PIN DESIGNATOR 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 GND B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 GND +VS CLK +VS OE 19 MSBI 20 21 +VS REFB B7 8 21 REFB B8 9 20 +VS B9 10 19 MSBI B10 11 18 OE B11 12 17 +VS B12 13 16 CLK 22 CM GND 14 15 +VS 23 REFT 24 25 26 27 28 +VS GND IN IN GND DESCRIPTION Ground Bit 1, Most Significant Bit Bit 2 Bit 3 Bit 4 Bit 5 Bit 6 Bit 7 Bit 8 Bit 9 Bit 10 Bit 11 Bit 12, Least Significant Bit Ground +5V Power Supply Convert Clock Input, 50% Duty Cycle +5V Power Supply HI: High Impedance State. LO or Floating: Normal Operation. Internal pull-down resistors. Most Significant Bit Inversion, HI: MSB inverted for complementary output. LO or Floating: Straight output. Internal pull-down resistors. +5V Power Supply Bottom Reference Bypass. For external bypassing of internal +1.25V reference. Common-Mode Voltage. It is derived by (REFT + REFB)/2. Top Reference Bypass. For external bypassing of internal +3.25V reference. +5V Power Supply Ground Input Complementary Input Ground TIMING DIAGRAM tCONV tL Convert Clock tD tH DATA LATENCY (6.5 Clock Cycles) Hold Hold Hold Hold Hold Hold Track "N + 1" Track "N + 2" Track "N + 3" Track "N + 4" Track "N + 5" Track "N + 6" Track (1) Track Internal Track-and-Hold Hold "N" t2 Output Data Data Valid N-8 Data Valid N-7 Data Valid N-6 N-5 N-4 N-3 N-2 N-1 N t1 Data Invalid SYMBOL tCONV tL tH tD t1 t2 DESCRIPTION MIN Convert Clock Period Clock Pulse LOW Clock Pulse HIGH Aperture Delay Data Hold Time, CL = 0pF New Data Delay Time, CL = 15pF max 25 12 12(2) TYP MAX UNITS 100s ns ns ns ns ns ns 12.5 12.5 2 3.9 12.5 NOTES: (1) " " indicates the portion of the waveform that will stretch out at slower sample rates. (2) tH must be 13ns minimum if no missing codes is desired only for the conditions of tCONV 28ns and fIN < 2MHz. 4 ADS800 www.ti.com SBAS035B TYPICAL CHARACTERISTICS At TA = +25C, VS = +5V, Sampling Rate = 40MHz, and with a 50% duty cycle clock having a 2ns rise-and-fall time, unless otherwise noted. SPECTRAL PERFORMANCE SPECTRAL PERFORMANCE 0 fIN = 500kHz -20 -20 -40 -40 Amplitude (dB) Amplitude (dB) 0 -60 -80 -100 fIN = 1MHz -60 -80 -100 -120 -120 0 5 10 15 20 0 5 Frequency (MHz) 10 15 SPECTRAL PERFORMANCE SPECTRAL PERFORMANCE 0 0 fIN = 12MHz -20 -20 -40 -40 Amplitude (dB) Amplitude (dB) fIN = 5MHz -60 -80 -100 -60 -80 -100 -120 -120 0 5 10 15 20 0 5 Frequency (MHz) 15 20 2-TONE INTERMODULATION 0 fIN = 1MHz fS = 10MHz -20 10 Frequency (MHz) SPECTRAL PERFORMANCE 0 f1 = 12.5MHz f2 = 12.0MHz -20 -40 Amplitude (dB) Amplitude (dB) 20 Frequency (MHz) -60 -80 -100 -40 -60 -80 -100 -120 -120 0 1 2 3 4 5 0 Frequency (MHz) 10 15 20 Frequency (MHz) ADS800 SBAS035B 5 www.ti.com 5 TYPICAL CHARACTERISTICS (Cont.) At TA = +25C, VS = +5V, Sampling Rate = 40MHz, and with a 50% duty cycle clock having a 2ns rise-and-fall time, unless otherwise noted. DIFFERENTIAL LINEARITY ERROR DIFFERENTIAL LINEARITY ERROR 2.0 2.0 fIN = 12MHz fIN = 500kHz 1.0 DLE (LSB) DLE (LSB) 1.0 0 -1.0 0 -1.0 -2.0 -2.0 0 1024 2048 3072 4096 0 1024 2048 3072 4096 Code Code SWEPT POWER SFDR DYNAMIC PERFORMANCE vs INPUT FREQUENCY 100 80 fIN = 12MHz 75 80 70 SFDR (dBFS) SFDR, SNR (dB) SFDR 65 60 60 40 SNR 20 55 50 0 0.1 1 10 -50 100 -40 -30 -20 SWEPT POWER SNR 10 4.0 fIN = 500kHz fIN = 12MHz 60 2.0 ILE (LSB) SNR (dB) 0 INTEGRAL LINEARITY ERROR 80 40 20 0 -2.0 0 -50 -40 -30 -20 -10 0 -4.0 10 0 Input Amplitude (dBm) 6 -10 Input Amplitude (dBm) Frequency (MHz) 1024 2048 3072 4096 Code ADS800 www.ti.com SBAS035B TYPICAL CHARACTERISTICS (Cont.) At TA = +25C, VS = +5V, Sampling Rate = 40MHz, and with a 50% duty cycle clock having a 2ns rise-and-fall time, unless otherwise noted. DYNAMIC PERFORMANCE vs DIFFERENTIAL FULL-SCALE INPUT RANGE DYNAMIC PERFORMANCE vs SINGLE-ENDED FULL-SCALE INPUT RANGE 75 65 fIN = 12MHz SFDR (fIN = 500kHz) SNR 60 Dynamic Range (dB) Dynamic Range (dB) 70 55 SFDR 50 SFDR (fIN = 12MHz) 65 SNR (fIN = 500kHz) 60 SNR (fIN = 12MHz) 55 NOTE: REFTEXT varied, REFB is fixed at the internal value of +1.25V. NOTE: REFTEXT varied, REFB is fixed at the internal value of +1.25V. 50 45 1 2 3 4 Single-Ended Full-Scale Range (Vp-p) 2 3 4 Differential Full-Scale Input Range (Vp-p) 5 SPURIOUS-FREE DYNAMIC RANGE (SFDR) vs TEMPERATURE SIGNAL-TO-NOISE RATIO vs TEMPERATURE 80 90 70 fIN = 500kHz fIN = 500kHz SNR (dB) SFDR (dBFS) 80 70 60 fIN = 12MHz 50 60 fIN = 12MHz 40 50 -25 0 25 50 -25 75 0 25 50 75 Temperature (C) Temperature (C) SIGNAL-TO-(NOISE + DISTORTION) vs TEMPERATURE SUPPLY CURRENT vs TEMPERATURE 70 85 fIN = 500kHz 80 IQ (mA) SINAD (dB) 65 60 75 fIN = 12MHz 55 50 70 -25 0 25 50 75 -25 ADS800 SBAS035B 0 25 50 75 Temperature (C) Temperature (C) www.ti.com 7 TYPICAL CHARACTERISTICS (Cont.) At TA = +25C, VS = +5V, Sampling Rate = 40MHz, and with a 50% duty cycle clock having a 2ns rise-and-fall time, unless otherwise noted. POWER DISSIPATION vs TEMPERATURE GAIN ERROR vs TEMPERATURE 0.75 425 Gain (%FSR) Power (mW) 0.25 400 375 -0.25 -0.75 -1.25 350 -25 0 25 50 75 -25 0 Temperature (C) 50 75 TRACK-MODE SMALL-SIGNAL INPUT BANDWIDTH OFFSET ERROR vs TEMPERATURE 1 Track-Mode Input Response (dB) -2.25 Offset (%FSR) 25 Temperature (C) -2.5 0 -1 -2 -3 -4 -5 -2.75 -25 0 25 50 75 10k 100k Ambient Temperature (C) 1M 10M 100M 1G Frequency (Hz) OUTPUT NOISE HISTOGRAM (NO SIGNAL) 800k Counts 600k 400k 200k 0.0 N-2 N-1 N N+1 N+2 Code 8 ADS800 www.ti.com SBAS035B THEORY OF OPERATION Op Amp Bias The ADS800 is a high-speed, sampling A/D converter with pipelining. It uses a fully differential architecture and digital error correction to ensure 12-bit resolution. The differential track-and-hold circuit is shown in Figure 1. The switches are controlled by an internal clock which has a non-overlapping 2-phase signal, 1 and 2. At the sampling time, the input signal is sampled on the bottom plates of the input capacitors. In the next clock phase, 2, the bottom plates of the input capacitors are connected together and the feedback capacitors are switched to the op amp output. At this time, the charge redistributes between CI and CH, completing one track-and-hold cycle. The differential output is a held DC representation of the analog input at the sample time. The track-and-hold circuit can also convert a single-ended input signal into a fully differential signal for the quantizer. 1 IN IN IN 2 1 2 OUT 1 OUT 1 CI 2 CH 1 1 Input Clock (50%) Op Amp Bias VCM Internal Non-Overlapping Clock 1 2 1 FIGURE 1. Input Track-and-Hold Configuration with Timing Signals. Digital Delay Input T/H 2-Bit Flash STAGE 1 1 CH CI The pipelined quantizer architecture has 11 stages with each stage containing a 2-bit quantizer and a 2-bit Digital-toAnalog Converter (DAC), as shown in Figure 2. Each 2-bit quantizer stage converts on the edge of the sub-clock, which is twice the frequency of the externally applied clock. The output of each quantizer is fed into its own delay line to time- IN VCM 2-Bit DAC + - x2 B1 (MSB) Digital Delay B2 STAGE 2 B3 2-Bit DAC Digital Error Correction 2-Bit Flash + - x2 B4 B5 B6 B7 B8 B9 B10 Digital Delay B11 B12 (LSB) 2-Bit Flash STAGE 10 2-Bit DAC + - x2 STAGE 11 2-Bit Flash Digital Delay FIGURE 2. Pipeline A/D Converter Architecture. ADS800 SBAS035B www.ti.com 9 align it with the data created from the following quantizer stages. This aligned data is fed into a digital error correction circuit which can adjust the output data based on the information found on the redundant bits. This technique gives the ADS800 excellent differential linearity and ensures no missing codes at the 12-bit level. Since there are two pipeline stages per external clock cycle, there is a 6.5 clock cycle data latency from the start convert signal to the valid output data. The output data is available in Straight Offset Binary (SOB) or Binary Two's Complement (BTC) format. * For most applications, the clock duty should be set to 50%. However, for applications requiring no missing codes, a slight skew in the duty cycle will improve DNL performance for conversion rates > 35MHz and input frequencies < 2MHz (see Timing Diagram) in the SO package. For the best performance in the SSOP package, the clock should be skewed under all input frequencies with conversion rates > 35MHz. A possible method for skewing the 50% duty cycle source is shown in Figure 4. ADS800 +3.25V 23 REFT 0.1F 2k +2.25V 22 RV = 217, typical 0.1F CLKIN 21 CLKOUT IC2 FIGURE 4. Clock Skew Circuit. DIGITAL OUTPUT DATA The 12-bit output data is provided at CMOS logic levels. The standard output coding is Straight Offset Binary (SOB) where a full-scale input signal corresponds to all "1's" at the output, as shown in Table 1. This condition is met with pin 19 "LO" or Floating due to an internal pull-down resistor. By applying a logic "HI" voltage to this pin, a Binary Two's Complement (BTC) output will be provided where the most significant bit is inverted. The digital outputs of the ADS800 can be set to a high-impedance state by driving OE (pin 18) with a logic "HI". Normal operation is achieved with pin 18 "LO" or Floating due to internal pull-down resistors. This function is provided for testability purposes and is not meant to drive digital buses directly or be dynamically changed during the conversion process. OUTPUT CODE 2k REFB 0.1F 0.1F IC1 To Internal Comparators CM IC1, IC2 = ACT04 RV 2k THE ANALOG INPUT AND INTERNAL REFERENCE The analog input of the ADS800 can be configured in various ways and driven with different circuits, depending on the nature of the signal and the level of performance desired. The ADS800 has an internal reference that sets the full-scale input range of the A/D converter. The differential input range has each input centered around the common-mode of +2.25V, with each of the two inputs having a full-scale range of +1.25V to +3.25V. Since each input is 2Vp-p and 180 outof-phase with the other, a 4V differential input signal to the quantizer results. As shown in Figure 3, the positive full-scale reference (REFT) and the negative full-scale (REFB) are brought out for external bypassing. In addition, the commonmode voltage (CM) may be used as a reference to provide the appropriate offset for the driving circuitry. However, care must be taken not to appreciably load this reference node. For more information regarding external references, singleended input, and ADS800 drive circuits, refer to the applications section. VDD VDD DIFFERENTIAL INPUT(1) +1.25V FIGURE 3. Internal Reference Structure. CLOCK REQUIREMENTS The CLK pin accepts a CMOS level clock input. Both the rising and falling edges of the externally applied clock control the various interstage conversions in the pipeline. Therefore, the clock signal's jitter, rise-and-fall times, and duty cycle can affect conversion performance. * Low clock jitter is critical to SNR performance in frequency-domain signal environments. +FS (IN = +3.25V, IN = +1.25V) +FS - 1LSB +FS - 2LSB +3/4 Full-Scale +1/2 Full-Scale +1/4 Full-Scale +1LSB Bipolar Zero (IN = IN = +2.25V) -1LSB -1/4 Full-Scale -1/2 Full-Scale -3/4 Full-Scale -FS + 1LSB -FS (IN = +1.25V, IN = +3.25V) SOB PIN 19 FLOATING or LO BTC PIN 19 HI 111111111111 111111111111 111111111110 111000000000 110000000000 101000000000 100000000001 100000000000 011111111111 011000000000 010000000000 001000000000 000000000001 000000000000 011111111111 011111111111 011111111110 011000000000 010000000000 001000000000 000000000001 000000000000 111111111111 111000000000 110000000000 101000000000 100000000001 100000000000 NOTE: (1) In the single-ended input mode, +FS = +4.25V and -FS = +0.25V. TABLE I. Coding Table for the ADS800. * Clock rise-and-fall times should be as short as possible (< 2ns for best performance). 10 ADS800 www.ti.com SBAS035B APPLICATIONS product performance. The input capacitors, CIN, and the input resistors, RIN, create a high-pass filter with the lower corner frequency at fC = 1/(2pRINCIN). The corner frequency can be reduced by either increasing the value of RIN or CIN. If the circuit operates with a 50 or 75 impedance level, the resistors are fixed and only the value of the capacitor can be increased. Usually, AC-coupling capacitors are electrolytic or tantalum capacitors with values of 1F or higher. It should be noted that these large capacitors become inductive with increased input frequency, which could lead to signal amplitude errors or oscillation. To maintain a low AC-coupling impedance throughout the signal band, a small value (e.g. 1F) ceramic capacitor could be added in parallel with the polarized capacitor. DRIVING THE ADS800 The ADS800 has a differential input with a common-mode of +2.25V. For AC-coupled applications, the simplest way to create this differential input is to drive the primary winding of a transformer with a single-ended input. A differential output is created on the secondary if the center tap is tied to the common-mode voltage of +2.25V, as per Figure 5. This transformer-coupled input arrangement provides good highfrequency AC performance. It is important to select a transformer that gives low distortion and does not exhibit core saturation at full-scale voltage levels. Since the transformer does not appreciably load the ladder, there is no need to buffer the Common-Mode (CM) output in this instance. In general, it is advisable to keep the current draw from the CM output pin below 0.5A to avoid nonlinearity in the internal reference ladder. A FET input operational amplifier such as the OPA130 can provide a buffered reference for driving external circuitry. The analog IN and IN inputs should be bypassed with 22pF capacitors to minimize track-and-hold glitches and to improve high input frequency performance. Capacitors CSH1 and CSH2 are used to minimize current glitches resulting from the switching in the input track-andhold stage and to improve signal-to-noise performance. These capacitors can also be used to establish a low-pass filter and effectively reduce the noise bandwidth. In order to create a real pole, resistors RSER1 and RSER2 were added in series with each input. The cutoff frequency of the filter is determined by fC = 1/(2pRSER * (CSH + CADC)) where RSER is the resistor in series with the input, CSH is the external capacitor from the input to ground, and CADC is the internal input capacitance of the A/D converter (typically 4pF). Figure 6 illustrates another possible low-cost interface circuit which utilizes resistors and capacitors in place of a transformer. Depending on the signal bandwidth, the component values should be carefully selected in order to maintain the Resistors R1 and R2 are used to derive the necessary common-mode voltage from the buffered top and bottom references. The total load of the resistor string should be selected so that the current does not exceed 1mA. Although the circuit in Figure 6 uses two resistors of equal value so that the common-mode voltage is centered between the top and bottom reference (+2.25V), it is not necessary to do so. In all cases the center point, VCM, should be bypassed to ground in order to provide a low-impedance AC ground. 22 CM 0.1F 26 IN AC Input Signal 22pF Mini-Circuits TT1-6-KK81 or equivalent ADS800 27 IN If the signal needs to be DC coupled to the input of the ADS800, an operational amplifier input circuit is required. In the differential input mode, any single-ended signal must be modified to create a differential signal. This can be accomplished by 22pF FIGURE 5. AC-Coupled Single-Ended to Differential Drive Circuit Using a Transformer. C1 0.1F CIN 0.1F RSER1(1) 49.9 R1 (6k) +3.25V Top Reference IN RIN1 25 RIN2 25 CIN 0.1F CSH1 22pF R3 1k C2 0.1F RSER2(1) 49.9 ADS8xx VCM R2 (6k) IN CSH2 22pF +1.25V Bottom Reference C3 0.1F NOTE: (1) Indicates optional component. FIGURE 6. AC-Coupled Differential Input Circuit. ADS800 SBAS035B www.ti.com 11 using two operational amplifiers, one in the noninverting mode for the input and the other amplifier in the inverting mode for the complementary input. The low distortion circuit in Figure 7 will provide the necessary input shifting required for signals centered around ground. It also employs a diode for output level shifting to ensure a low distortion +3.25V output swing. Other amplifiers can be used in place of the OPA842s if the lowest distortion is not necessary. If output level shifting circuits are not used, care must be taken to select operational amplifiers that give the necessary performance when swinging to +3.25V with a 5V supply operational amplifier. age, as shown in Figure 8. This configuration will result in increased even-order harmonics, especially at higher input frequencies. However, this tradeoff may be quite acceptable for time-domain applications. The driving amplifier must give adequate performance with a +0.25V to +4.25V output swing in this case. EXTERNAL REFERENCES AND ADJUSTMENT OF FULL-SCALE RANGE The internal reference buffers are limited to approximately 1mA of output current. As a result, these internal +1.25V and +3.25V references may be overridden by external references that have at least 18mA (at room temperature) of output drive capability. In this instance, the common-mode voltage will be The ADS800 can also be configured with a single-ended input full-scale range of +0.25V to +4.25V by tying the complementary input to the common-mode reference volt- +5V 604 +5V 301 BAS16(1) Optional High Impedance Input Amplifier 301 301 27 IN OPA842 2.49k 0.1F +5V(2) 22pF 0.1F -5V 604 DC-Coupled Input Signal +5V OPA842 604 49.9 OPA130 +5V -5V 24.9 ADS800 2.49k +2.25V 22 CM +5V 301 BAS16(1) Input Level Shift Buffer 301 26 IN OPA842 22pF 0.1F -5V 604 NOTES: (1) A Philips BAS16 diode or equivalent may be used. (2) Supply bypassing not shown. 301 FIGURE 7. A Low Distortion DC-Coupled, Single-Ended to Differential Input Driver Circuit. 22 CM 0.1F ADS800 Single-Ended Input Signal 26 IN 27 IN 22pF Full Scale = +0.25V to +4.25V with internal references. FIGURE 8. Single-Ended Input Connection. 12 ADS800 www.ti.com SBAS035B The circuit in Figure 10 works completely on a single +5V supply. As a reference element, it uses the micro-power reference REF1004-2.5, which is set to a quiescent current of 0.1mA. Amplifier A2 is configured as a follower to buffer the +1.25V generated from the resistor divider. To provide the necessary current drive, a pull-down resistor, RP, is added. set halfway between the two references. This feature can be used to adjust the gain error, improve gain drift, or to change the full-scale input range of the ADS800. Changing the fullscale range to a lower value has the benefit of easing the swing requirements of external input drive amplifiers. The external references can vary as long as the value of the external top reference (REFTEXT) is less than or equal to +3.4V, the value of the external bottom reference (REFBEXT) is greater than or equal to +1.1V, and the difference between the external references are greater than or equal to 1.5V. Amplifier A1 is configured as an adjustable gain stage, with a range of approximately 1 to 1.32. The pull-up resistor again relieves the op amp from providing the full current drive. The value of the pull-up/down resistors is not critical and can be varied to optimize power consumption. The need for pull-up, pull-down resistors depends only on the drive capability of the selected drive amplifiers and thus can be omitted. For the differential configuration, the full-scale input range will be set to the external reference values that are selected. For the single-ended mode, the input range is 2 * (REFTEXT - REFBEXT), with the common-mode being centered at (REFTEXT + REFBEXT)/2. Refer to the typical characteristics for "Expected Performance vs Full-Scale Input Range". -541 +5V 0.1F +VS CLK Ext Clk 0.1F R1 50 +VS OE MSBI 0.1F +VS REFB CM REFT 0.1F 0.1F 0.1F 0.1F AC Input Signal +VS GND IN R2 50 IN 22pF Mini-Circuits TT1-6-KK81 or equivalent (1) 22pF GND 15 14 16 13 17 12 GND 11 9 12 8 13 7 14 6 15 5 16 4 17 3 18 2 LSB 1 19 18 11 19 10 20 9 21 8 23 24 25 26 27 28 7 6 5 4 3 2 1 G+ -541 ADS800 22 Dir MSB 11 9 12 8 13 7 14 6 15 5 16 4 17 3 18 2 GND 1 19 Dir G+ NOTE: (1) All capacitors should be located as close to the pins as the manufacturing process will allow. Ceramic X7R surface-mount capacitors or equivalent are recommended. FIGURE 9. ADS800 Interface Schematic with AC-Coupling and External Buffers. ADS800 SBAS035B www.ti.com 13 +5V RP 220 A1 1/2 OPA2234 +5V Top Reference +2.5V to +3.25V 2k 10k 6.2k 10k REF1004 +2.5V 10k(1) A2 1/2 OPA2234 0.1F +1.25V 10k Bottom Reference RP 220 10k(1) NOTE: (1) Use parts alternatively for adjustment capability. FIGURE 10. Optional External Reference to Set the Full-Scale Range Utilizing a Dual, Single-Supply Op Amp. PC BOARD LAYOUT AND BYPASSING A well-designed, clean PC board layout will assure proper operation and clean spectral response. Proper grounding and bypassing, short lead lengths, and the use of ground planes are particularly important for high-frequency circuits. Multilayer PC boards are recommended for best performance but if carefully designed, a two-sided PC board with large, heavy ground planes can give excellent results. It is recommended that the analog and digital ground pins of the ADS800 be connected directly to the analog ground plane. In our experience, this gives the most consistent results. The A/D converter power-supply commons should be tied together at the analog ground plane. Power supplies should be bypassed with 0.1F ceramic capacitors as close to the pin as possible. DYNAMIC PERFORMANCE DEFINITIONS 1. The ADS800 is a high performance converter and careful attention to test techniques is necessary to achieve accurate results. Highly accurate phase-locked signal sources allow high resolution FFT measurements to be made without using data windowing functions. A low jitter signal generator such as the HP8644A for the test signal, phase-locked with a low jitter Signal-to-Noise-and-Distortion Ratio (SINAD): 10 log 2. Sinewave Signal Power Noise + Harmonic Power (first 15 harmonics) Signal-to-Noise Ratio (SNR): 10 log 3. DYNAMIC PERFORMANCE TESTING 14 HP8022A pulse generator for the A/D converter clock, gives excellent results. Low-pass filtering (or bandpass filtering) of test signals is absolutely necessary to test the low distortion of the ADS800. Using a signal amplitude slightly lower than fullscale will allow a small amount of "headroom" so that noise or DC offset voltage will not over-range the A/D converter and cause clipping on signal peaks. Sinewave Signal Power Noise Power Intermodulation Distortion (IMD): 10 log Highest IMD Pr oduct Power ( to 5th - order ) Sinewave Signal Power IMD is referenced to the larger of the test signals, f1 or f2. Five "bins" either side of peak are used for calculation of fundamental and harmonic power. The "0" frequency bin (DC) is not included in these calculations as it is of little importance in dynamic signal processing applications. ADS800 www.ti.com SBAS035B PACKAGE OPTION ADDENDUM www.ti.com 31-Mar-2008 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty Lead/Ball Finish MSL Peak Temp (3) ADS800E OBSOLETE SSOP DB 28 TBD Call TI Call TI ADS800E/1K OBSOLETE SSOP DB 28 TBD Call TI Call TI ADS800U ACTIVE SOIC DW 28 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR ADS800U/1K ACTIVE SOIC DW 28 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR ADS800U/1KG4 ACTIVE SOIC DW 28 1000 Green (RoHS & no Sb/Br) CU NIPDAU Level-2-260C-1 YEAR ADS800UG4 ACTIVE SOIC DW 28 CU NIPDAU Level-2-260C-1 YEAR 20 20 Green (RoHS & no Sb/Br) (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 29-Mar-2008 TAPE AND REEL INFORMATION *All dimensions are nominal Device ADS800U/1K Package Package Pins Type Drawing SOIC DW 28 SPQ Reel Reel Diameter Width (mm) W1 (mm) 1000 330.0 32.4 Pack Materials-Page 1 A0 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 11.35 18.67 3.1 16.0 32.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 29-Mar-2008 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) ADS800U/1K SOIC DW 28 1000 346.0 346.0 49.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Amplifiers Data Converters DSP Clocks and Timers Interface Logic Power Mgmt Microcontrollers RFID RF/IF and ZigBee(R) Solutions amplifier.ti.com dataconverter.ti.com dsp.ti.com www.ti.com/clocks interface.ti.com logic.ti.com power.ti.com microcontroller.ti.com www.ti-rfid.com www.ti.com/lprf Applications Audio Automotive Broadband Digital Control Medical Military Optical Networking Security Telephony Video & Imaging Wireless www.ti.com/audio www.ti.com/automotive www.ti.com/broadband www.ti.com/digitalcontrol www.ti.com/medical www.ti.com/military www.ti.com/opticalnetwork www.ti.com/security www.ti.com/telephony www.ti.com/video www.ti.com/wireless Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2008, Texas Instruments Incorporated