279
FIBER
SENSORS
LASER
SENSORS
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA COMPONENTS
MACHINE VISION
SYSTEMS
UV CURING
SYSTEMS
Selection
Guide
Amplier
Built-in
Power Supply
Built-in
Amplier-
separated
EX-Z
CX-400
CY-100
EX-10
EX-20
EX-30
EX-40
CX-440
EQ-30
EQ-500
MQ-W
RX-LS200
RX
RT-610
Related Information
Recognition
PNP output
type available
Smallest body, just 3.5 mm 0.138 in thick
It can be mounted in a very
small space as its size is just
W10 × H14.5 × D3.5 mm
W0.394 × H0.571 × D0.138 in
(thru-beam, front sensing type).
Flexible mounting
The diffuse reective type sensor is front sensing and is
so thin that it gives an impression of being just pasted
on the mounting base. The thru-beam type is available
as front sensing type, as well as, side sensing type,
allowing exible mounting.
Ultra-slim Photoelectric Sensor Amplier Built-in
EX-10 SERIES Ver.2
■General terms and conditions ............. F-3
■Selection guide
............................. P.231~
Amplier built-in extraordinarily small and slim size
Certified
(Some models only)
Glossary of terms / General precautions
.....
P.1549~ / P.1552~
■Korea’s S-mark ............................. P.1602
panasonic.net/id/pidsx/global
Thru-beam
• Front sensing type
Diffuse reective
• Front sensing type
• Side sensing type
A wide variety of narrow-beam type! Light diffusion is approx. 1/2 of standard type.
Less interference with no slit,
narrow-pitch can be set.
The pitch of installation is 1/2 of
conventional models, so that the
close-installation is possible. No cost
is necessary to purchase or install
a slit.
EX-11□ / EX-11E□
EX-11S□ / EX-11SE□
EX-19S□
Possible to sense a minute object
less than ø0.5 mm ø0.039 in with
no slit.
The series is applicable to sense a
minute object without any cost.
ø0.5mm
Long sensing range of 1 m 3.281
ft with narrow beam
A long 1 m 3.281 ft sensing range is
possible with narrow beam.
EX-11S□
EX-□S□
(Excluding some models)
Ver.2
Ultra-slim Photoelectric Sensor EX-10 SERIES Ver.2
280
FIBER
SENSORS
LASER
SENSORS
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA COMPONENTS
MACHINE VISION
SYSTEMS
UV CURING
SYSTEMS
Selection
Guide
Amplier
Built-in
Power Supply
Built-in
Amplier-
separated
EX-Z
CX-400
CY-100
EX-10
EX-20
EX-30
EX-40
CX-440
EQ-30
EQ-500
MQ-W
RX-LS200
RX
RT-610
APPLICATIONS
Positioning of PCBs Detecting ICs Detecting PCB rack
Detecting wafer cassette Detecting thin ring
Checking for absence of capacitor in tray
EX-14□
Transparent stick
IC EX-15□
EX-19S□
EX-14□
Guide
EX-13E□
EX-14□
Background suppression
Black object reliably detected
It can reliably detect dark
color objects since it is
convergent reective type.
Hardly affected by background
Even a specular background
separated by 100 mm 3.937
in, or more, is not detected.
(However, the background
should be directly opposite.
A spherical or curved
background may be
detected.)
100 mm
3.937 in
Background
The best distance
is approx. 10 mm
0.394 in from the
object.
EX-14□
Minimum sensing object: ø1 mm ø0.039 in
EX-11□, EX-11E□, EX-15 and
EX-15E are
incorporated
with ø1 mm ø0.039 in
slit masks so that ø1 mm
ø0.039 in, or more, object
can be detected. Hence,
they are suitable for precise
positioning or small parts
detection.
EX-11(E)□, EX-15(E)□
Long sensing range: 1 m 3.281 ft
A sensing range of 1 m
3.281 ft has been realized
with a slim size of just 3.5
mm 0.138 in. It can be used
to detect even wide IC trays.
EX-19(E)□
1 m
3.281 ft
Electric power saving *
The EX-10 series
achieves reductions
in power consumption
of up to 65 %. These
sensors contribute
to environmental
friendliness.
* Effective from production
in October 2010.
High-speed response time: 0.5 ms
The sensor is suitable for detecting small and high-
speed traveling objects.
BASIC PERFORMANCE
A maximum 35 %
reduction
compared to conventional
sensors
281
Ultra-slim Photoelectric Sensor EX-10 SERIES Ver.2
FIBER
SENSORS
LASER
SENSORS
PHOTOELECTRIC
SENSORS
MICRO
PHOTOELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASUREMENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA COMPONENTS
MACHINE VISION
SYSTEMS
UV CURING
SYSTEMS
Selection
Guide
Amplier
Built-in
Power Supply
Built-in
Amplier-
separated
EX-Z
CX-400
CY-100
EX-10
EX-20
EX-30
EX-40
CX-440
EQ-30
EQ-500
MQ-W
RX-LS200
RX
RT-610
MOUNTING / SIZE
Mountable with M3 screws
Non-corrosive stainless steel type sensor mounting bracket is also available.
• MS-EX10-1
[Cold rolled carbon steel (SPCC)]
MS-EX10-11
[Stainless steel (SUS304)]
• MS-EX10-2
[Cold rolled carbon steel (SPCC)]
MS-EX10-12
[Stainless steel (SUS304)]
• MS-EX10-3
[Cold rolled carbon steel (SPCC)]
MS-EX10-13
[Stainless steel (SUS304)]
(L-shaped mounting bracket)
Red beam makes beam alignment easy
The red LED beam projected from the emitter helps you
to align the sensor heads.
M3 screws
M3 screws
M3 screws
SENS.
EX
-17
SENS.
EX
-17
Operation mode switch
Operation indicator
(Orange)
Even for the thru-beam
type sensor, only three
wires have to be connected.
Operation mode switch
Thru-beam type sensor incorporated with an operation
mode switch on the bifurcation is also available. It helps
you to test the operability before start-up.
EX-15□/17□
VARIETIES
mounting bracket for the front
sensing type
mounting bracket for the side
sensing type
FUNCTIONS
OTHERS
Bright 2-color indicator
Less resources used *
A convenient 2-color
indicator has been
incorporated in the
miniature body.
Based on environmental
considerations, simplied
packaging is used in order
to reduce waste.
In addition, the bag is
made from polyethylene
which produces no toxic
gases even when burned.
* Effective from production in
October 2010.
2-color indicator
Orange: Operation indicator
Green: Stability indicator
Bending durability
Bending-resistant cable type EX-□-R is available. It is
most suitable for moving parts, such as robot arm, etc.
EX-□-R
ENVIRONMENTAL RESISTANCE
Waterproof IP67
The sensors features an IP67 rating to allow their use
in process lines where water is used or splashed.
Rust-resistant stainless steel sensor mounting brackets
are available.
Note: If water splashes on the sensor during sensing operation, it may
sense water as an object.
Incorporated an inverter countermeasure circuit *
The EX-10 series become
signicantly stronger
against inverter light and
other extraneous light.
* Effective from production in
October 2010.
Note: Sensor mounting brackets can not be used for
the narrow beam type (EX-□S□).
Ultra-slim Photoelectric Sensor EX-10 SERIES Ver.2
282
FIBER
SENSORS
LASER
SENSORS
PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO-
ELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASURE-
MENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
Selection
Guide
Amplier
Built-in
Power Supply
Built-in
Amplier-
separated
EX-Z
CX-400
CY-100
EX-10
EX-20
EX-30
EX-40
CX-440
EQ-30
EQ-500
MQ-W
RX-LS200
RX
RT-610
ORDER GUIDE
Type Appearance Sensing range Model No.(Note 2) Output
operation Output
NPN output PNP output
Standard type
Thru-beam
Front sensing
150 mm 5.906 in EX-11A EX-11A-PN Light-ON
NPN open-
collector
transistor
or
PNP open-
collector
transistor
EX-11B EX-11B-PN Dark-ON
500 mm
19.685 in
EX-13A EX-13A-PN Light-ON
EX-13B EX-13B-PN Dark-ON
1 m
3.281 ft
EX-19A EX-19A-PN Light-ON
EX-19B EX-19B-PN Dark-ON
With operation mode
switch on the bifurcation
150 mm 5.906 in EX-15 EX-15 -PN
Switchable
either
Light-ON or
Dark-ON
500 mm
19.685 in
EX-17 EX-17-PN
Side sensing
150 mm 5.906 in EX-11EA EX-11EA-PN Light-ON
EX-11EB EX-11EB-PN Dark-ON
500 mm
19.685 in
EX-13EA EX-13EA-PN Light-ON
EX-13EB EX-13EB-PN Dark-ON
1 m
3.281 ft
EX-19EA EX-19EA-PN Light-ON
EX-19EB EX-19EB-PN Dark-ON
With operation mode
switch on the bifurcation
150 mm 5.906 in
EX-15E
-
Switchable
either
Light-ON or
Dark-ON
500 mm
19.685 in
EX-17E
-
Convergent reective
(Diffused beam type)
Front sensing
2 to 25 mm 0.079 to 0.984 in
(Note 1)
(Convergent point: 10 mm 0.394 in)
EX-14A EX-14A-PN Light-ON
EX-14B EX-14B-PN Dark-ON
Narrow beam type
Thru-beam
Front sensing
150 mm 5.906 in
EX-11SA EX-11SA-PN Light-ON
NPN open-
collector
transistor
or
PNP open-
collector
transistor
EX-11SB EX-11SB-PN Dark-ON
500 mm
19.685 in
EX-13SA EX-13SA-PN Light-ON
EX-13SB EX-13SB-PN Dark-ON
1 m
3.281 ft
EX-19SA EX-19SA-PN Light-ON
EX-19SB EX-19SB-PN Dark-ON
Side sensing
150 mm
5.906 in
EX-11SEA
EX-11SEA-PN
Light-ON
EX-11SEB
EX-11SEB-PN
Dark-ON
500 mm
19.685 in
EX-13SEA
EX-13SEA-PN
Light-ON
EX-13SEB
EX-13SEB-PN
Dark-ON
NOTE: Mounting bracket is not supplied with the sensor. Please select from the range of optional sensor mounting brackets
(MS-EX10-□). Sensor mounting brackets (MS-EX10-□) can not be used for the narrow beam type (EX-□S□).
Notes: 1) The sensor does not detect even a specular background if it is separated by 100 mm 3.937 in or more. (However, the background should be directly
opposite. A spherical or curved background may be detected.)
2) The model No. with “P” shown on the label afxed to the thru-beam type sensor is the emitter, “D” shown on the label is the receiver.
Bending-resistant cable type is also available for NPN output type. (excluding narrow beam type EX-□S□ and sensor with operation mode switch on the
bifurcation EX-15□/17□)
When ordering this type, sufx “-R” to the model No.
(e.g.) Bending-resistant cable type of EX-11A is “EX-11A-R”.
Bending-resistant cable type
5 m 16.404 ft cable length type (standard: 2 m 6.562 ft) is also available for NPN output type. (excluding narrow beam type EX-□S□ and bending-resistant cable type)
When ordering this type, sufx “-C5” to the model No.
(e.g.) 5 m 16.404 ft cable length type of EX-11A is “EX-11A-C5”.
5 m 16.404 ft cable length type
283
Ultra-slim Photoelectric Sensor EX-10 SERIES Ver.2
FIBER
SENSORS
LASER
SENSORS
PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO-
ELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASURE-
MENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
Selection
Guide
Amplier
Built-in
Power Supply
Built-in
Amplier-
separated
EX-Z
CX-400
CY-100
EX-10
EX-20
EX-30
EX-40
CX-440
EQ-30
EQ-500
MQ-W
RX-LS200
RX
RT-610
Designation Model No. Description
Sensor mounting
bracket
(Note 1)
MS-EX10-1
Mounting bracket for the front sensing type sensor [Cold rolled carbon steel (SPCC)]
(The thru-beam type sensor needs two brackets.)
MS-EX10-2
Mounting bracket for the side sensing type sensor [Cold rolled carbon steel (SPCC)]
(The thru-beam type sensor needs two brackets.)
MS-EX10-3
L-shaped mounting bracket sensor [Cold rolled carbon steel (SPCC)]
(The thru-beam type sensor needs two brackets.)
MS-EX10-11
Mounting bracket for the front sensing type sensor [Stainless steel (SUS304)]
(The thru-beam type sensor needs two brackets.)
MS-EX10-12
Mounting bracket for the side sensing type sensor [Stainless steel (SUS304)]
(The thru-beam type sensor needs two brackets.)
MS-EX10-13
L-shaped mounting bracket [Stainless steel (SUS304)]
(The thru-beam type sensor needs two brackets.)
Slit mask
OS-EX10-12
(Slit size ø1.2 mm ø0.047 in)
Slit on one side
• Sensing range: 600 mm 23.622 in [EX-19□]
250 mm 9.843 in [EX-13□, EX-17□]
• Min. sensing object: ø2 mm ø0.079 in
Slit on both sides
• Sensing range: 400 mm 15.748 in [EX-19□]
200 mm 7.874 in [EX-13□, EX-17□]
• Min. sensing object: ø1.2 mm ø0.047 in
OS-EX10-15
(Slit size ø1.5 mm ø0.059 in)
Slit on one side
• Sensing range: 800 mm 31.496 in [EX-19□]
350 mm 13.780 in [EX-13□]
• Min. sensing object: ø2 mm ø0.079 in
Slit on both sides
• Sensing range: 500 mm 19.685 in [EX-19□]
300 mm 11.811 in [EX-13□]
• Min. sensing object: ø1.5 mm ø0.059 in
OS-EX10E-12
(Slit size ø1.2 mm ø0.047 in)
Slit on one side
• Sensing range: 400 mm 15.748 in [EX-19E□] (Note 3)
250 mm 9.843 in [EX-13E□, EX-17E□]
• Min. sensing object: ø2 mm ø0.079 in
Slit on both sides
• Sensing range: 200 mm 7.874 in [EX-13E□, EX-17E□]
• Min. sensing object: ø1.2 mm ø0.047 in
Sensor checker
(Note 2)
CHX-SC2
It is useful for beam alignment of thru-beam type sensors. The optimum
receiver position is given by indicators, as well as an audio signal.
Mounting screw MS-M2 Mounting screws with washers (50 pcs. lot). It can mount
securely as it is spring washer attached.
Sensor mounting bracket
• MS-EX10-1
Material: Cold rolled
carbon steel (SPCC)
(Uni-chrome plated)
Two M2 (length 4 mm
0.157 in) pan head
screws are attached.
• MS-EX10-11
Material: Stainless
steel (SUS304)
Two M2 (length 4 mm
0.157 in) pan head
screws [stainless
steel (SUS304)] are
attached.
• MS-EX10-2
Material: Cold rolled
carbon steel (SPCC)
(Uni-chrome plated)
Two M2 (length 8 mm
0.315 in) pan head
screws are attached.
• MS-EX10-12
Material: Stainless
steel (SUS304)
Two M2 (length 8 mm
0.315 in) pan head
screws [stainless
steel (SUS304)] are
attached.
• MS-EX10-3
Material: Cold rolled
carbon steel (SPCC)
(Uni-chrome plated)
Two M2 (length 4 mm
0.157 in) pan head
screws, and two M2
(length 8 mm 0.315 in)
pan head screws are
attached.
• MS-EX10-13
Material: Stainless steel
(SUS304)
Two M2 (length 4 mm
0.157 in) pan head
screws [stainless
steel (SUS304)] and
two M2 (length 8 mm
0.315 in) pan head
screws [stainless steel
(SUS304)] are attached.
Notes: 1) Can not be used for the narrow beam type (EX-□S□).
2) Refer to p.959~ for the sensor checker CHX-SC2.
3) Since EX-19E□ has a built-in ø1 mm ø 0.039 in slit in the emitter, be sure to mount it in the
receiver.
LEVEL
POWER
CHX-SC2
Sensor checker
Sensor checker
• CHX-SC2
Slit mask
• OS-EX10-12
• OS-EX10-15
• OS-EX10E-12 Example of mounting
(OS-EX10E-12)
Tighten along with the sensor
mounting bracket.
OPTIONS
NOTE:
Sensor mounting brackets can not be used for the narrow beam type (EX-□S□).
Ultra-slim Photoelectric Sensor EX-10 SERIES Ver.2
284
FIBER
SENSORS
LASER
SENSORS
PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO-
ELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASURE-
MENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
Selection
Guide
Amplier
Built-in
Power Supply
Built-in
Amplier-
separated
EX-Z
CX-400
CY-100
EX-10
EX-20
EX-30
EX-40
CX-440
EQ-30
EQ-500
MQ-W
RX-LS200
RX
RT-610
SPECIFICATIONS
Notes: 1) Where measurement conditions have not been specied precisely, the conditions used were an ambient temperature of +23 °C +73.4 °F.
2) Model Nos. having the sufx “-PN” are PNP output type.
3) The bending-resistant cable type (model Nos. having sufx “-R”) has a 0.1 mm2 3-core (thru-beam type emitter: 2-core) bending-resistant cabtyre cable,
2 m 6.562 ft long.
Type Thru-beam • standard type
Front sensing Side sensing Front sensing Side sensing Front sensing Side sensing
Model No.
(Note 2)
Light-ON EX-11A(-PN)EX-11EA(-PN)EX-13A(-PN)EX-13EA(-PN)EX-19A(-PN)EX-19EA(-PN)
Item
Dark-ON EX-11B(-PN)EX-11EB(-PN)EX-13B(-PN)EX-13EB(-PN)EX-19B(-PN)EX-19EB(-PN)
CE marking directive compliance
EMC Directive, RoHS Directive
Sensing range 150 mm 5.906 in 500 mm 19.685 in
1 m 3.281 ft
Min. sensing object
ø1 mm ø0.039 in opaque object
(Completely beam interrupted object)
Setting distance
between emitter
and receiver:
150 mm 5.906 in
ø2 mm ø0.079 in opaque object
(Completely beam interrupted object)
Setting distance
between emitter
and receiver:
500 mm 19.685 in
ø2 mm ø0.079 in
opaque object
Completely beam
interrupted object
Setting distance between
emitter and receiver:
1 m 3.281 ft
Hysteresis
–
Repeatability (perpendicular to sensing axis)
0.05 mm 0.002 in or less
Supply voltage 12 to 24 V DC ±10 % Ripple P-P 10 % or less
Current consumption Emitter: 10 mA or less, Receiver: 10 mA or less
Output
<NPN output type>
NPN open-collector transistor
• Maximum sink current: 50 mA
• Applied voltage: 30 V DC or less (between output and 0 V)
• Residual voltage: 2 V or less (at 50 mA sink current)
1 V or less (at 16 mA sink current)
<PNP output type>
PNP open-collector transistor
• Maximum source current: 50 mA
• Applied voltage: 30 V DC or less (between output and +V)
• Residual voltage: 2 V or less (at 50 mA source current)
1 V or less (at 16 mA source current)
Utilization category DC-12 or DC-13
Short-circuit protection Incorporated
Response time 0.5 ms or less
Operation indicator Orange LED (lights up when the output is ON)
Incident beam indicator
–
Stability indicator Green LED
(lights up under stable light received condition or stable dark condition)
Environmental resistance
Pollution degree 3 (Industrial environment)
Protection IP67 (IEC)
Ambient temperature −25 to +55 °C −13 to +131 °F (No dew condensation or icing allowed), Storage: −30 to +70 °C −22 to +158 °F
Ambient humidity 35 to 85 % RH, Storage: 35 to 85 % RH
Ambient illuminance Incandescent light: 3,000 ℓx or less at the light-receiving face
Voltage withstandability 1,000 V AC for one min. between all supply terminals connected together and enclosure
Insulation resistance 20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
Vibration resistance 10 to 500 Hz frequency, 3 mm 0.118 in double amplitude in X, Y and Z directions for two hours each
Shock resistance 500 m/s2 acceleration (50 G approx.) in X, Y and Z directions three times each
Emitting element Red LED [Peak emission wavelength: 680 nm 0.027 mil (EX-19E□: 624 nm 0.025 mil), modulated]
Material Enclosure: Polyethylene terephthalate, Lens: Polyalylate
Cable (Note 3) 0.1 mm2 3-core (thru-beam type emitter: 2-core) cabtyre cable, 2 m 6.562 ft long
Cable extension Extension up to total 50 m 164 ft is possible with 0.3 mm2, or more, cable (thru-beam type: emitter and receiver).
Weight Net weight (each emitter and receiver): 20 g approx., Gross weight: 50 g approx.
Accessories Mounting screws: 1 set
285
Ultra-slim Photoelectric Sensor EX-10 SERIES Ver.2
FIBER
SENSORS
LASER
SENSORS
PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO-
ELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASURE-
MENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
Selection
Guide
Amplier
Built-in
Power Supply
Built-in
Amplier-
separated
EX-Z
CX-400
CY-100
EX-10
EX-20
EX-30
EX-40
CX-440
EQ-30
EQ-500
MQ-W
RX-LS200
RX
RT-610
SPECIFICATIONS
Type Thru-beam • narrow beam type
Convergent reective
(Diffused beam type)
Thru-beam · with operation mode switch on bifurcation
Front sensing
Side sensing
Front sensing
Side sensing
Front sensing Front sensing Front sensing
Side sensing
Front sensing
Side sensing
Model No.
(Note 2)
Light-ON
EX-11SA(-PN)
EX-11SEA(-PN)EX-13SA(-PN)EX-13SEA(-PN)
EX-19SA(-PN)EX-14A(-PN)
EX-15
(Note 3)
EX-15E
(Note 3)
EX-17
(Note 3)
EX-17E
(Note 3)
Item
Dark-ON
EX-11SB(-PN)
EX-11SEB(-PN)EX-13SB(-PN)EX-13SEB(-PN)
EX-19SB(-PN)EX-14B(-PN)
CE marking directive compliance
EMC Directive, RoHS Directive
–
Sensing range 150 mm 5.906 in 500 mm 19.685 in
1 m 3.281 ft
2 to 25 mm 0.079
to 0.984 in (Note 4)
(Conv. point: 10 mm 0.394 in)
150 mm 5.906 in 500 mm 19.685 in
Min. sensing object
ø0.5 mm
ø0.002 in
opaque object
(Completely
beam interrupted
object)
(Note 5)
ø1 mm ø0.039 in opaque object
(Completely beam interrupted object)
(Note 5)
ø2 mm ø0.079 in opaque object
(Completely beam interrupted object)
(Note 5)
ø0.1 mm ø0.004
in copper wire
Setting distance:
10 mm 0.394 in
ø1 mm ø0.039 in opaque object
(Completely beam interrupted object)
Setting distance
between emitter
and receiver:
150 mm 5.906 in
ø2 mm ø0.079 in opaque object
(Completely beam interrupted object)
Setting distance
between emitter
and receiver:
500 mm 19.685 in
Hysteresis
–
15 % or less of operation
distance (Note 4)
–
Repeatability (perpendicular to sensing axis)
0.05 mm 0.002 in or less
0.1 mm 0.004 in or less
0.05 mm 0.002 in or less
Supply voltage 12 to 24 V DC ±10 % Ripple P-P 10 % or less
Current consumption Emitter: 10 mA or less, Receiver: 10 mA or less
13 mA or less
25 mA or less
Output
<NPN output type>
NPN open-collector transistor
•
Maximum sink current: 50 mA
•
Applied voltage: 30 V DC or less (between output and 0 V)
•
Residual voltage: 2 V or less (at 50 mA sink current)
1 V or less (at 16 mA sink current)
<PNP output type>
PNP open-collector transistor
•
Maximum source current: 50 mA
•
Applied voltage: 30 V DC or less (between output and +V)
•
Residual voltage: 2 V or less (at 50 mA source current)
1 V or less (at 16 mA source current)
NPN open-collector transistor
• Maximum sink current: 100 mA
•
Applied voltage: 30 V DC or less (between output and 0 V)
•
Residual voltage: 2 V or less
(at 100 mA sink current)
1 V or less (at 16 mA sink current)
Utilization category DC-12 or DC-13
–
Short-circuit protection Incorporated
Response time 0.5 ms or less
Operation indicator Orange LED (lights up when the output is ON)
Orange LED (lights up when the output is ON), located on the bifurcation
Incident beam indicator
–
Orange LED (lights up under light received
condition), located on the receiver
Stability indicator Green LED
(lights up under stable light received condition or stable dark condition)
Green LED (lights up under stable light received
condition or stable dark condition), located on the
receiver
Environmental resistance
Pollution degree 3 (Industrial environment)
–
Protection IP67 (IEC)
Ambient temperature −25 to +55 °C −13 to +131 °F (No dew condensation or icing allowed), Storage: −30 to +70 °C −22 to +158 °F
Ambient humidity 35 to 85 % RH, Storage: 35 to 85 % RH
Ambient illuminance Incandescent light: 3,000 ℓx or less at the light-receiving face
Voltage withstandability 1,000 V AC for one min. between all supply terminals connected together and enclosure
Insulation resistance 20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure
Vibration resistance 10 to 500 Hz frequency, 3 mm 0.118 in double amplitude in X, Y and Z directions for two hours each
Shock resistance 500 m/s2 acceleration (50 G approx.) in X, Y and Z directions three times each
Emitting element
Red LED (Peak emission wavelength: 650 nm 0.026 mil, modulated) Red LED (Peak emission wavelength: 680 nm 0.027 mil, modulated)
Material Enclosure: Polyethylene terephthalate
Lens: Polyalylate
Enclosure: Polyethylene terephthalate
Lens: Polyalylate, Bifurcation: Polyalylate
Cable (Note 6) 0.1 mm2 3-core (thru-beam type emitter: 2-core) cabtyre cable,
2 m 6.562 ft long
0.2 mm
2
3-core cabtyre cable, 2 m 6.562 ft long (beyond bifurcation;
from emitter / receiver to bifurcation: 0.5 m 1.640 ft long)
Cable extension
Extension up to total 50 m 164 ft is possible with 0.3 mm
2
, or more, cable (thru-beam type: emitter and receiver).
Extension up to total 100 m 328 ft is possible with 0.3 mm
2
, or more, cable.
Weight Net weight (each emitter and receiver): 20 g approx.,
Gross weight: 50 g approx.
Net weight: 20 g approx.
Gross weight: 40 g approx.
Net weight: 55 g approx., Gross weight: 80 g approx.
Accessories Mounting screws: 1 set
Mounting screws: 1 set
Mounting screws: 1 set, Adjusting screwdriver: 1 pc.
Notes: 1) Where measurement conditions have not been specied precisely, the conditions used were an ambient temperature of +23 °C +73.4 °F.
2) Model Nos. having the sufx “-PN” are PNP output type.
3) Either Light-ON or Dark-ON can be selected by the operation mode switch.
4)
The sensing range and the hysteresis of convergent reective type sensor are specied for white non-glossy paper (50 × 50 mm 1.969 × 1.969 in) as the object.
5) The min. sensing objects are specied in case the emitter / reciever sensing range is to set the maximum.
6) The bending-resistant cable type (model Nos. having sufx “-R”) has a 0.1 mm2 3-core (thru-beam type emitter: 2-core) bending-resistant cabtyre cable,
2 m 6.562 ft long.
Ultra-slim Photoelectric Sensor EX-10 SERIES Ver.2
286
FIBER
SENSORS
LASER
SENSORS
PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO-
ELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASURE-
MENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
Selection
Guide
Amplier
Built-in
Power Supply
Built-in
Amplier-
separated
EX-Z
CX-400
CY-100
EX-10
EX-20
EX-30
EX-40
CX-440
EQ-30
EQ-500
MQ-W
RX-LS200
RX
RT-610
I/O CIRCUIT AND WIRING DIAGRAMS
EX-11□ EX-11S□ EX-13□ EX-13S□ EX-19□ EX-19S□ EX-14□NPN output type
I/O circuit diagram Wiring diagram
Brown
Black (Note)
Blue
Load
12 to 24 V DC
±10 %
+
−
Note: The emitter of the thru-beam type sensor does not incorporate the
black wire.
EX-11□-PN EX-11S□-PN EX-13□-PN EX-13S□-PN EX-19□-PN EX-19S□-PN EX-14□-PN PNP output type
I/O circuit diagram Wiring diagram
Users’ circuit Internal circuit
Color code
50 mA max.
Sensor circuit
Tr
D1
D2
ZD
Load
(Brown) +V
(Black)
Output (Note)
(Blue) 0 V
+
−
12 to 24 V DC
±10 %
Note: The emitter of the thru-beam type sensor does not incorporate the
output.
Symbols … D1: Reverse supply polarity protection diode
D2: Reverse output polarity protection diode
ZD: Surge absorption zener diode
Tr
: NPN output transistor
Users’ circuit Internal circuit
D1
D2
50 mA max.
ZD
Tr
Load
(Black) Output (Note)
(Blue) 0 V
12 to 24 V DC
±10 %
Sensor circuit
Color code
(Brown) +V
+
−
Note: The emitter of the thru-beam type sensor does not incorporate the
output.
Symbols … D1: Reverse supply polarity protection diode
D2: Reverse output polarity protection diode
ZD: Surge absorption zener diode
Tr
: PNP output transistor
Brown
Black (Note)
Blue
Load
12 to 24 V DC
±10 %
+
−
Note: The emitter of the thru-beam type sensor does not incorporate the
black wire.
EX-15□ EX-15E□ EX-17□ EX-17E□NPN output type
I/O circuit diagram
Users’ circuit Internal circuit
Color code
100 mA max.
Sensor circuit
Tr
D1
D2
ZD
Load
(Brown) +V
(Black) Output
(Blue) 0 V
12 to 24 V DC
±10 %
+
−
Symbols … D1: Reverse supply polarity protection diode
D2: Reverse output polarity protection diode
ZD: Surge absorption zener diode
Tr
: NPN output transistor
12 to 24 V DC
±10 %
Load
Brown
Black
Blue
+
−
EX-15□, EX-15E□, EX-17□, EX-17E□ wiring diagram
287
Ultra-slim Photoelectric Sensor EX-10 SERIES Ver.2
FIBER
SENSORS
LASER
SENSORS
PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO-
ELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASURE-
MENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
Selection
Guide
Amplier
Built-in
Power Supply
Built-in
Amplier-
separated
EX-Z
CX-400
CY-100
EX-10
EX-20
EX-30
EX-40
CX-440
EQ-30
EQ-500
MQ-W
RX-LS200
RX
RT-610
SENSING CHARACTERISTICS (TYPICAL)
EX-11□ EX-11E□ EX-15□ EX-15E□Thru-beam type
Parallel deviation Angular deviation
50
1.969
50
1.969
25
0
25
0
50
1.969
100
3.937
150
5.906
200
7.874
EX-11□
EX-15□
EX-11E
□
EX-15E
□
EX-11E
□
EX-15E
□
EX-11□
EX-15□
Receiver
L
ℓ
Emitter
Emitter
Receiver
L
ℓ
Setting distance L (mm in)
Left Right
Center
Operating point ℓ (mm in)
0.984 0.984
Emitter
Receiver
Emitter
Receiver
20 10 01
02
0
0
50
1.969
100
3.937
150
5.906
200
7.874
Left Right
Center
Operating angle θ ( ° )
EX-11□
EX-15□
EX-11□
EX-15□
EX-11E□
EX-15E□
L
θ
L
θ
Setting distance L (mm in)
EX-11E
□
EX-15E
□
EX-13□ EX-13E□ EX-17□ EX-17E□Thru-beam type
Parallel deviation Angular deviation Parallel deviation with slit
masks (ø1.2 mm ø0.047 in)
Parallel deviation with slit
masks (ø1.5 mm ø0.059 in)
100
3.937
50
1.969
050
1.969
100
3.937
0
Slit on one side
or both sides
Slit on one side,
sensing range: 350 mm 13.78 in
Slit on both sides,
sensing range: 300 mm 11.81 in
Receiver
Emitter
L
ℓ
400
15.748
300
11.811
200
7.874
100
3.937
Setting distance L (mm in)
Left Right
Center
Operating point ℓ (mm in)
40
1.575
20
0.787
020
0.787
40
1.575
0
EX-13
□
/17
□
Slit on one side
Receiver
Emitter
L
ℓ
400
15.748
300
11.811
200
7.874
100
3.937
EX-13
□
/17
□
Slit on both sides
EX-13E
□
/
17E
□
Slit on one side
EX-13E□/17E□
Slit on
both sides
Setting distance L (mm in)
Left Right
Center
Operating point ℓ (mm in)
Emitter
Receiver
Receiver
20 10 0 10
20
Left Right
Center
Operating angle θ ( ° )
EX-13
□
EX-17
□
L
θ L
θ
Emitter
EX-13□
EX-17□
0
200
7.874
400
15.748
600
23.622
800
31.496
EX-13E
□
EX-17E
□
EX-13E□
EX-17E□
Setting distance L (mm in)
Emitter
Receiver
Emitter
Receiver
100
3.937
50
1.969
050
1.969
100
3.937
0
Left Right
Center
Operating point ℓ (mm in)
200
7.874
400
15.748
600
23.622
800
31.496
EX-13□
EX-17□
EX-13
□
EX-17
□
EX-13E□
EX-17E□
EX-13E
□
EX-17E
□
L
ℓL
ℓ
Setting distance L (mm in)
EX-19□Thru-beam type
Parallel deviation
Parallel deviation Parallel deviation Parallel deviation Parallel deviation
Angular deviation Parallel deviation with slit
masks (ø1.2 mm ø0.047 in)
Parallel deviation with slit
masks (ø1.5 mm ø0.059 in)
200
7.874
100
3.937
0 100
3.937
200
7.874
0
500
19.685
1,000
39.370
Slit on one side
Slit on both sides
Receiver
Emitter
L
ℓ
Setting distance L (mm in)
Left Right
Center
Operating point ℓ (mm in)
200
7.874
100
3.937
0 100
3.937
200
7.874
0
200
7.874
400
15.748
600
23.622
800
31.496
Slit on one side
Slit on both sides
Receiver
Emitter
L
ℓ
Setting distance L (mm in)
Left Right
Center
Operating point ℓ (mm in)
40 20 02
04
0
0
500
19.685
1,000
39.370
L
θ
Receiver
Emitter
Setting distance L (mm in)
Left Right
Center
Operating angle θ ( ° )
200
7.874
100
3.937
0 100
3.937
200
7.874
0
500
19.685
1,000
39.370
Receiver
Emitter
L
ℓ
Setting distance L (mm in)
Left Right
Center
Operating point ℓ (mm in)
Beam from Emitter 1
may be caught by Receiver 2.
Receiver 1
Receiver 2
Emitter 2
Emitter 1
L
ℓ × 2 or more
Receiver 1
Receiver 2
Emitter 1
Emitter 2
*Optical properties of side sensing types (
EX-□E□
)
Due to the optical properties of side sensing types, note that sensing may
be affected if multiple sensors are positioned in such a way that optical
axes intersect as shown in the diagram below.
There is no problem when
sensors are installed in
parallel
(although the distance
between sensors should be
ℓ × 2 or more).
EX-19E□
EX-11S□
/
EX-11SE□ EX-13S□
/
EX-13SE□
EX-19S□ Thru-beam typeThru-beam typeThru-beam typeThru-beam type
200 100 0 100 200
0
500
1,000
L
ℓ
Receiver
Emitter
Setting distance L (mm in)
39.370
19.685
7.874
Operating point ℓ (mm in)
CenterLeft Right
7.8743.937 3.937
25 0 25
50
1.969
50
1.969
0
EX-11S□
EX-11SE□
EX-11S□
EX-11SE□
50
100
150
200
7.874
5.906
3.937
1.969
Setting distance L (mm in)
Receiver
Emitter
L
ℓL
ℓ
Receiver
Emitter
Operating point ℓ (mm in)
CenterLeft Right
0.984 0.984 25 0 25
EX-13S□
EX-13SE□EX-13S□
EX-13SE□
0
200
400
600
800
31.496
23.622
15.784
7.874
Setting distance L (mm in)
50
Operating point ℓ (mm in)
CenterLeft Right
1.969 0.984 0.984
50
1.969
Receiver
Emitter
L
ℓL
ℓ
Receiver
Emitter
50 0 50
Receiver
Emitter
Lℓ
0
500
1,000
39.370
19.685
Setting distance L (mm in)
100
3.937 1.969 1.969
100
3.937
Operating point ℓ (mm in)
CenterLeft Right
Ultra-slim Photoelectric Sensor EX-10 SERIES Ver.2
288
FIBER
SENSORS
LASER
SENSORS
PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO-
ELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASURE-
MENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
Selection
Guide
Amplier
Built-in
Power Supply
Built-in
Amplier-
separated
EX-Z
CX-400
CY-100
EX-10
EX-20
EX-30
EX-40
CX-440
EQ-30
EQ-500
MQ-W
RX-LS200
RX
RT-610
SENSING CHARACTERISTICS (TYPICAL)
EX-14□Convergent reective type
Sensing elds
• Horizontal (left and right) direction
• Vertical (up and down) direction
5
0.197
10
0.394
05
0.197
10
0.394
0
10
0.394
20
0.787
30
1.181
40
1.575
White
N4
7 mm
0.276 in
ℓ
L
Setting distance L (mm in)
Left Right
Center
Operating point ℓ (mm in)
50 × 50 mm 1.969 × 1.969 in
Non-glossy paper
5
0.197
10
0.394
05
0.197
10
0.394
0
10
0.394
20
0.787
30
1.181
40
1.575
White
N4
ℓ
7.75
mm
0.305 in
L
Setting distance L (mm in)
Down Up
Center
Operating point ℓ (mm in)
50 × 50 mm
1.969 × 1.969 in
Non-glossy paper
Correlation between lightness and sensing range
Correlation between material (50 × 50 mm 1.969 × 1.969 in) and sensing range
0
10
0.394
20
0.787
30
1.181
40
1.575
N2 N4 N6 N8
Lightness LightDark
N2N1 N3 N4 N5 N6 N7 N8 N9
Sensing range L (mm in)
Sensing region
Distance to
convergent point
0
20
0.787
10
0.394
40
1.575
60
2.362
80
3.150
Sensing range L (mm in)
Black circuit board
Black rubber sheet
IC tray (Black)
Glass epoxy printed circuit board
(Green masked surface)
Ceramic circuit board
White non-glossy paper
Stainless steel plate
Aluminum plate
(Hair line)
Aluminum-evaporated mirror
Distance to convergent point
The sensing region (typical) is
represented by oblique lines
in the left gure. However, the
sensitivity should be set with
enough margin because of
slight variation in products.
The bars in the graph indicate
the sensing range (typical)
for the respective material.
However, there is a slight
variation in the sensing range
depending on the product.
Further, if there is a reective
object (conveyor, etc.) in the
background of the sensing
object, since it affects the
sensing, separate it by more
than twice the sensing range
shown in the left graph.
Lightness shown on the left
may differ slightly from the
actual object condition.
PRECAUTIONS FOR PROPER USE Refer to p.1552~ for general precautions.
Mounting
• In case of mounting on tapped holes (Unit: mm in)
Sensing
direction
Sensing
direction
Attached screw
[M2 (length 10 0.394)]
Attached screw
[M2 (length 8 0.315)]
M2 × 0.4 0.016 hole
tapped, 7 0.276 deep
M2 × 0.4 0.016 hole
tapped, 6 0.157 deep
11
0.433
11
0.433
The tightening torque should be 0.2 N·m or less.
• In case of using attached screws and nuts (Unit: mm in)
Attached screw
Attached screw
Thickness of
mounting plate: 2 0.079 or less
Thickness of
mounting plate: 2.5 0.098 or less
Spring washers
Nuts
Flat washers
[M2 (length 10 0.394)]
[M2 (length 8 0.315)]
Sensing
direction
Sensing
direction
11
0.433
11
0.433
The tightening torque should be 0.2 N·m or less.
Side sensing
Side sensing Front sensing
Front sensing
Operation mode switch
(EX-15□, EX-15E□, EX-17□ and EX-17E□ only)
Operation mode switch
L: Light-ON
D: Dark-ON
Lights up when the output is
ON.
Operation indicator (Orange)
Others
• Do not use during the initial transient time (50 ms)
after the power supply is switched on.
• Excess bending of the cable or stress applied to the
cable may disconnect the internal lead wire.
Switch
position Description
Light-ON mode is set when the switch is turned fully
clockwise (L side).
Dark-ON mode is set when the switch is turned fully
counterclockwise (D side).
• Never use this product as a sensing device
for personnel protection.
• In case of using sensing devices for
personnel protection, use products which
meet laws and standards, such as OSHA,
ANSI or IEC etc., for personnel protection
applicable in each region or country.
289
Ultra-slim Photoelectric Sensor EX-10 SERIES Ver.2
FIBER
SENSORS
LASER
SENSORS
PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO-
ELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASURE-
MENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
Selection
Guide
Amplier
Built-in
Power Supply
Built-in
Amplier-
separated
EX-Z
CX-400
CY-100
EX-10
EX-20
EX-30
EX-40
CX-440
EQ-30
EQ-500
MQ-W
RX-LS200
RX
RT-610
EX-11□ EX-11S□ EX-13□ EX-13S□ EX-19□ EX-19S□Sensor
2-ø2.2 ø0.087
mounting holes
Beam-
emitting
part
11
0.433
1.75 0.069
4.5
0.177
14.5
0.571
5.5
0.217
10
0.394
1.75 0.069
2.1
0.083
3.5
0.138
ø2.5 ø0.098 cable, 2 m 6.562 ft long
6.5
0.256
4
0.157
2.1
0.083
4
0.157
3.5
0.138
5.5
0.217
10
0.394
6.45
0.254
Beam-
receiving
part
2-ø2.2 ø0.087
mounting holes
ø2.5 ø0.098 cable, 2 m 6.562 ft long
11
0.433
1.75
0.069
4.5
0.177
14.5
0.571
1.5
0.059
6.5
0.256
Stability
indicator
(Green)
Operation
indicator
(Orange)
1.75
0.069
EX-11E□ EX-11SE□ EX-13E□ EX-13SE□ EX-19E□ Sensor
2-ø2.2 ø0.087
mounting holes
ø2.5
ø0.098 cable, 2 m 6.562 ft long
11
0.433
1.75 0.069
4.5
0.177
14.5
0.571
10
0.394
1.75 0.069
6.5
0.256
4
0.157
Beam-
emitting
part
4.5
0.177
2.25
0.089
4.2
0.165
Stability
indicator (Green)
Operation
indicator (Orange)
Beam-
receiving
part
4.5
0.177
2.25
0.089
4.2
0.165
4
0.157
10
0.394
6.45
0.254
1.75
0.069
2-ø2.2 ø0.087
mounting holes
ø2.5 ø0.098 cable, 2 m 6.562 ft long
11
0.433
1.75
0.069
4.5
0.177
14.5
0.571
1.5
0.059
6.5
0.256
Sensor
EX-15 EX-17
500
19.685
2.1
0.083
3.5
0.138
38
1.496
15.2 0.598
8
0.315
7
0.276
1 0.039
1.75
0.069
5.5
0.217
4
0.157
4.5
0.177
1.5
0.059
19.2
0.756
11
0.433
1.75
0.069
6.45 0.254
Beam-
receiving
part
Incident beam indicator (Orange)
Stability indicator (Green)
5.5
0.217
1.75
0.069
11
0.433
4
0.157
10
0.394
10 0.394
1.75
0.069
2-ø2.2 ø0.087
mounting holes
ø2.5 ø0.098 cables
Operation mode switch
Operation indicator
(Orange)
2-ø2.2 ø0.087
mounting holes
Beam-
emitting
part
2.1
0.083
3.5
0.138
ø3.8 ø0.150 cable,
2 m 6.562 ft long
14.5
0.571
4.5
0.177
14.5
0.571
Sensor
EX-15E EX-17E
Operation mode switch
500
19.685
38
1.496
15.2 0.598
8
0.315
7
0.276
1 0.039
19.2
0.756
Beam-
emitting
part
4
0.157
11
0.433
1.75
0.069
1.75
0.069
10
0.394
6.45
0.254
4.2
0.165
1.75
0.069
4.2
0.165
2.25
0.089
4.5
0.177
4.5
0.177
14.5
0.571
11
0.433
1.75
0.069
4
0.157
10
0.394
1.5
0.059
14.5
0.571
4.5
0.177
Operation indicator
(Orange)
ø2.5 ø0.098 cables
2-ø2.2
ø0.087
mounting holes
Beam-
receiving
part
Stability indicator (Green)
Incident beam indicator (Orange)
2-ø2.2 ø0.087
mounting holes
2.25
0.089
4.5
0.177
ø3.8 ø0.150 cable,
2 m 6.562 ft long
ReceiverEmitter
ReceiverEmitter
Emitter Receiver Emitter Receiver
DIMENSIONS (Unit: mm in)The CAD data can be downloaded from our website.
Ultra-slim Photoelectric Sensor EX-10 SERIES Ver.2
290
FIBER
SENSORS
LASER
SENSORS
PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO-
ELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASURE-
MENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
Selection
Guide
Amplier
Built-in
Power Supply
Built-in
Amplier-
separated
EX-Z
CX-400
CY-100
EX-10
EX-20
EX-30
EX-40
CX-440
EQ-30
EQ-500
MQ-W
RX-LS200
RX
RT-610
EX-14□Sensor
Stability indicator
(Green)
Operation
indicator (Orange)
1.75
0.069
2.75
0.108
6.45
0.254
13
0.512
2.1
0.083
3.5
0.138
4.5
0.177
Beam-
receiving
part
Beam-emitting part
2-ø2.2 ø0.087 mounting holes
ø2.5 ø0.098 cable,
2 m 6.562 ft long
4.5
0.177 14.5
0.571
11
0.433
1.5
0.059
1.75
0.069
8
0.315
5
0.197
MS-EX10-1 Sensor mounting bracket (Optional)
Assembly dimensions
Mounting drawing with EX-14□
Beam-
emitting
part
Beam-
receiving
part
3
0.118
5
0.197
10.75
0.423
4.25 0.167
1.25
0.049
t 1.2
t 0.047
3.7
0.146
3.5
0.138
20 0.787
13
0.512
22.75 0.896
7.6
0.299
(0.7)
(0.028)
(4.9)
(0.193)
3.5
0.138
8
0.315
(8.8)
(0.346)
15
0.591
11
0.433
8
0.315
2-ø3.4 ø0.134 mounting holes
4-M2 × 0.4
0.016
thru-hole threads
2-ø3.4 ø0.134 mounting holes
6.5
0.256
11
0.433
15
0.591
8
0.315
7.6
0.299
3.5
0.138
20
0.787
8
0.315
3.7
0.146
t 1.2
t 0.047
Material: Cold rolled carbon steel (SPCC)
(Uni-chrome plated)
Two M2 (length 4 mm 0.157 in) pan head screws are attached.
MS-EX10-2 Sensor mounting bracket (Optional)
Assembly dimensions
Mounting drawing with EX-11E□ and EX-13E□
10
0.394
7.6
0.299
3.2
0.126
0.25
0.010
4.25
0.167
1.4
0.055
1.25
0.049
2.5 0.098
t 1.2
t 0.047
6.25
0.246
4.5
0.177
(1.3)
(0.051)
11
0.433
15
0.591
8
0.315
8
0.315
3.5
0.138
20
0.787
Beam-
receiving
part
4
0.157
(7.45)
(0.293)
(2.3)
(0.091)
2-M2 × 0.4
0.016
thru-hole threads
t 1.2
t 0.047
15
0.591
11
0.433
20
0.787
6.25
0.246
8
0.315
3.5
0.138
8
0.315
1.4
0.055
3.2
0.126
7.6
0.299
Material: Cold rolled carbon steel (SPCC)
(Uni-chrome plated)
Two M2 (length 8 mm 0.315 in) pan head screws are attached.
DIMENSIONS (Unit: mm in)The CAD data can be downloaded from our website.
291
Ultra-slim Photoelectric Sensor EX-10 SERIES Ver.2
FIBER
SENSORS
LASER
SENSORS
PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO-
ELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASURE-
MENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
Selection
Guide
Amplier
Built-in
Power Supply
Built-in
Amplier-
separated
EX-Z
CX-400
CY-100
EX-10
EX-20
EX-30
EX-40
CX-440
EQ-30
EQ-500
MQ-W
RX-LS200
RX
RT-610
MS-EX10-3 Sensor mounting bracket (Optional)
Assembly dimensions
Mounting drawing with EX-14□
Beam
-
receiving part
Beam-
emitting part
(2.75)
(0.108)
10.8
0.425
t 1.2
t 0.047
(0.7)
(0.028)
13
0.512
5
0.197
1.75 0.069
1.25
0.049
3
0.118
11
0.438
15
0.591
4.25
0.167
3.5
0.138
10.5
0.413 3.2
0.126
1.4
0.055
8
0.315
6.25
0.246
7
0.276
Material: Cold rolled carbon steel (SPCC)
(Uni-chrome plated)
Two M2 (length 4 mm 0.157 in) pan head screws and two M2 (length 8 mm 0.315 in) pan
head screws are attached.
4-M2 × 0.4 0.016
thru-hole threads
2
0.079
6.5
0.256
3.2
0.126
8
0.315
10.8
0.425
7 0.276 10.5
0.413
1.4
0.055
11
0.433
15
0.591
t 1.2
t 0.047
MS-EX10-11 Sensor mounting bracket (Optional)
11
0.433
3.2
0.126
1.4
0.055
3.2
0.126
1.25
0.049
4.25
0.167
1.4
0.055
15
0.591
22.75
0.896
3.5
0.138
8
0.315
3
0.118
8.1
0.319
20
0.787
t 1.2
t 0.047
3.7
0.146
3.5
0.138
(4.9)
(0.193)
(0.7)
(0.028)
13
0.512
5
0.197
10.75 0.423
Beam-emitting part
Beam-receiving part
(9.3)
(0.366)
8 0.315
4-M2 × 0.4 0.016
thru-hole threads
11
0.433
3.2
0.126
1.4
0.055
3.2
0.126
1.4
0.055
15
0.591
20
0.787
6.5
0.256
3.5
0.138
8
0.315
8
0.315
8.1
0.319
t 1.2
t 0.047
3.7
0.146
Material: Stainless steel (SUS304)
Two M2 (length 4 mm 0.157 in) pan head screws [stainless steel (SUS304)] are attached.
MS-EX10-12 Sensor mounting bracket (Optional)
Assembly dimensions
Mounting drawing with EX-11E□ and EX-13E□























W
W


%HDP
UHFHLYLQJ
SDUW
















2-M2 × 0.4 0.016
thru-hole threads
11
0.433
3.2
0.126
1.4
0.055
3.2
0.126
1.4
0.055
15
0.591
6.25
0.246
20
0.787
8
0.315
8.1
0.319
t 1.2
t 0.047
8
0.315
3.5
0.138
Material: Stainless steel (SUS304)
Two M2 (length 8 mm 0.315 in) pan head screws [stainless steel (SUS304)] are attached.
DIMENSIONS (Unit: mm in)The CAD data can be downloaded from our website.
Assembly dimensions
Mounting drawing with EX-14□
Ultra-slim Photoelectric Sensor EX-10 SERIES Ver.2
292
FIBER
SENSORS
LASER
SENSORS
PHOTO-
ELECTRIC
SENSORS
MICRO
PHOTO-
ELECTRIC
SENSORS
AREA
SENSORS
SAFETY LIGHT
CURTAINS /
SAFETY
COMPONENTS
PRESSURE /
FLOW
SENSORS
INDUCTIVE
PROXIMITY
SENSORS
PARTICULAR
USE
SENSORS
SENSOR
OPTIONS
SIMPLE
WIRE-SAVING
UNITS
WIRE-SAVING
SYSTEMS
MEASURE-
MENT
SENSORS
STATIC
CONTROL
DEVICES
LASER
MARKERS
PLC
HUMAN
MACHINE
INTERFACES
ENERGY
MANAGEMENT
SOLUTIONS
FA
COMPONENTS
MACHINE
VISION
SYSTEMS
UV
CURING
SYSTEMS
Selection
Guide
Amplier
Built-in
Power Supply
Built-in
Amplier-
separated
EX-Z
CX-400
CY-100
EX-10
EX-20
EX-30
EX-40
CX-440
EQ-30
EQ-500
MQ-W
RX-LS200
RX
RT-610
MS-EX10-13 Sensor mounting bracket (Optional)
Assembly dimensions
Mounting drawing with EX-14□
Material: Stainless steel (SUS304)
Two M2 (length 4 mm 0.157 in) pan head screws [stainless steel (SUS304)] and two M2
(length 8 mm 0.315 in) pan head screws [stainless steel (SUS304)] are attached.
4-M2 × 0.4 0.016
thru-hole threads
t 1.2
t 0.047
10.8
0.425
11
0.433
10.5
0.413
6.5 0.256
3.2 0.126
2
0.079
15
0.591
7
0.276
1.4
0.055
1.4 0.055
8
0.315
3.2 0.126
11
0.433
3.2
0.126
1.25
0.049
4.25
0.167
15
0.591
8
0.315
3
0.118
3.2
0.126
1.4
0.055
13
0.512
10.5
0.413
3.5
0.138
1.75
0.069
10.8
0.425
5
0.197
1.4
0.055
Beam-emitting
part
Beam-receiving
part
t 1.2
t 0.047
(2.75)
(0.108)
(0.7)
(0.028)
6.25
0.246 7
0.276
DIMENSIONS (Unit: mm in)The CAD data can be downloaded from our website.