Instruction Sheet 408-8417 SL, KL, and Secure SL Series 110Connect Modular Jacks Optional BendLimiting Strain Relief 1375200-1 (Cat 6) 1375200-2 (Cat 5e) (See Figure 3) 16 OCT 07 Rev L 3. TERMINATION 1. Strip back only as much cable jacket as necessary to perform termination. See Figure 2. NOTE Generally, a strip length of 50.8 mm [2.00 in. ] maximum will meet the needs of most i applications, depending on method of termination. NOTE If using the optional bend-limiting strain relief, slide it over cable jacket as shown in Figure 2. i Universal Wiring 50.8 Label [2.00] Optional Bend-Limiting Strain Relief 1375200-1 or -2 (See Figure 3) Figure 2 SL Series 110Connect Modular Jack (shown) NOTE PRODUCT INFORMATION at the number at the bottom of this page, or visit the AMP NETCONNECT website at www.ampnetconnect.com. 12.7 mm [.50 in.] for CAT 5e Jacks, or 6.0 mm [.24 in.] for CAT 6 Jacks. NOTE 1. INTRODUCTION (Figure 1) Wire termination requires the use of Impact Tool 1583608-1 or SL Jack Termination Tool This instruction sheet provides termination procedures for the SL Series 110Connect (Cat 3, Cat 5e, and Cat 6) modular jacks; the KL Series 110Connect (Cat 5e and Cat 6) modular jacks; and Secure SL Series 110Connect (Cat 6) modular jacks. i 1725150-1. Refer to 408-8858 for SL Jack Termination Tool instructions. CAUTION Set impact setting for low-impact. Orient tool so cutoff blade is on outside of block and vertical. ! All dimensions are in millimeters [with inches in brackets]. Figures and illustrations are for i i 2. Align and lace a color-coded wire pair with the appropriate slots as indicated by the color coding on the wiring label (use minimum slack while maintaining twist, as indicated in Figure 3). Figure 1 NOTE Keep wire pairs twisted to within 75 mm [3 in.] of termination for Cat 3 jacks, or To obtain information on AMP NETCONNECT products, call reference only and are not drawn to scale. 3. Use tool to punch wires down into slot and cut off excess wire. Remove loose wire pieces. 4. Repeat Steps 2 and 3 with all wire pairs. Reasons for reissue of this sheet are provided in Section 4, REVISION SUMMARY. 2. DESCRIPTION The jacks accept four pair, twisted-pair cable with 22 through 24 AWG solid conductors and 24 AWG stranded conductors. The maximum conductor insulation diameter is 1.45 mm [.057 in.]. E 2007 Tyco Electronics Corporation, Harrisburg, PA All International Rights Reserved 5. Slide bend-limiting strain relief (if used) onto jack. Latches on strain relief will engage tabs on rear of jack as indicated in Figure 3. S New format S Deleted old and superceded part numbers in 4. REVISION SUMMARY NOTE in Paragraph 3.2 and Figure 3 TOOLING ASSISTANCE CENTER 1-800-722-1111 This controlled document is subject to change. PRODUCT INFORMATION 1-800-522-6752 For latest revision and Regional Customer Service, TE logo, AMP NETCONNECT, and Tyco Electronics are trademarks. *Trademark. Other products, logos, and company names used are the property of their respective owners. visit our website at www.tycoelectronics.com 1 of 2 LOC B 408-8417 SL, KL, and Secure SL Series 110Connect Modular Jacks Four-Pair Color-Coded Universal Wiring Label Three-Pair Color-Coded Wiring Label T568A Color Pattern T568B Color Pattern Keep Wires Twisted to Within 12.7 mm [.50 in.] of Keep Wires Twisted to Termination for CAT 5e Within 75 mm [3 in.] Jacks or 6.0 mm [.24 in.] of of Termination for Termination for CAT 6 CAT 3 Jacks Jacks Wires Cut Off Wires Cut Off Latches on Strain Relief Engage Tabs on Jack Impact Tool 1583608-1 Cutoff Blade Insertion Blade Where Space is Limited, 40.97 Strain Relief 1375157-1 [1.613] May be Used as Shown SL Series 110Connect Modular Jack (shown) 31.47 [1.239] Figure 3 2 of 2 Tyco Electronics Corporation Rev L