DS96173,DS96175 DS96173/DS96175 RS-485/RS-422 Quad Differential Line Receivers Literature Number: SNLS391B DS96173/DS96175 RS-485/RS-422 Quad Differential Line Receivers General Description Features The DS96173 and DS96175 are high speed quad differential line receivers designed to meet EIA Standard RS-485. The devices have TRI-STATE (R) outputs and are optimized for balanced multipoint data bus transmission at rates up to 10 Mbps. The receivers feature high input impedance, input hysteresis for increased noise immunity, and input sensitivity of 200 mV over a common mode input voltage range of -7V to +12V. The receivers are therefore suitable for multipoint applications in noisy environments. The DS96173 features an active high and active low Enable, common to all four receivers. The DS96175 features separate active high Enables for each receiver pair. Compatible RS-485 drivers, transceivers, and repeaters are also offered to provide optimum bus performance. The respective device types are DS96172, DS96174, DS96176 and DS96177. n n n n n n n n n Meets EIA Standard RS-485, RS-422A, RS-423A Designed for multipoint bus applications TRI-STATE Outputs Common mode input voltage range: -7V to +12V Operates from single +5V supply Input sensitivity of 200 mV over common mode range Input hysteresis of 50 mV typical High input impedance DS96173/DS96175 are lead and function compatible with SN75173/75175 or the AM26LS32/MC3486 respectively Connection Diagrams 16-Lead DIP DS96175 16-Lead DIP DS96173 00962802 00962801 Order Number DS96173CN or DS96175CN See NS Package Number N16E TRI-STATE (R) is a registered trademark of National Semiconductor Corporation. (c) 2004 National Semiconductor Corporation DS009628 www.national.com DS96173/DS96175 RS-485/RS-422 Quad Differential Line Receivers June 1998 DS96173/DS96175 Absolute Maximum Ratings (Note 2) Low Level Output Current If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Recommended Operating Conditions Storage Temperature Range Molded DIP Min -65C to +150C Lead Temperature Molded DIP (soldering, 10 sec.) Supply Voltage (VCC) 4.75 Common Mode Input Supply Voltage Differential Input Differential Input Voltage Enable Input Voltage 5 Units 5.25 V -7 +12 V -7 +12 V -400 A 16 mA 70 C Voltage (VID) 1.84W Output Current High (IOH) 7V Input Voltage, A or B Inputs Typ Max Voltage (VCM) 265C Maximum Power Dissipation (Note 1) at 25C N-Molded Package 50 mA Output Current LOW (IOL) 25V 25V Operating Temperature (TA) 0 25 Note 1: Derate molded DIP package 15 mW/C above 25C. 7V Electrical Characteristics (Notes 3, 4) over recommended temperature, common mode input voltage, and supply voltage ranges, unless otherwise specified Symbol VTH Parameter Differential Input Conditions Min Typ VO = 2.7V, IO = - 0.4 mA Max Units 0.2 V High Threshold Voltage VTL Differential Input (Note 5) VO = 0.5V, IO = 16 mA -0.2 V Low Threshold Voltage VT+ - VT- Hysteresis (Note 6) VIH Enable Input Voltage HIGH VIL Enable Input Voltage LOW VIC Enable Input Clamp Voltage II = -18 mA VOH Output Voltage HIGH VID = 200 mV, IOH = -400 A VOL Output Voltage LOW VID = -200 mV VCM = 0V 50 mV 2.0 V 0.8 V -1.5 V 2.7 V IOL = 8 mA 0.45 IOL = 16 mA 0.50 V 20 A VI = 12V 1.0 mA VI = -7V -0.8 IOZ High Impedance State Output VO = 0.4V to 2.4V II Line Input Current (Note 7) Other Input = 0V IIH Enable Input Current HIGH VIH = 2.7V 20 A IIL Enable Input Current LOW VIL = 0.4V -100 A RI Input Resistance IOS Short Circuit Output Current (Note 8) -85 mA ICC Supply Current Outputs Disabled 75 mA 12 -15 k Note 2: "Absolute Maximum Ratings" are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the devices should be operated at these limits. The tables of "Electrical Characteristics" provide conditions for actual device operation. Note 3: Unless otherwise specified Min/Max limits apply across the 0C to +70C range for the DS96173/DS96175. All typicals are given for VCC = 5V and TA = 25C. Note 4: All currents into the device pins are positive; all currents out of the device pins are negative. All voltages are reference to ground unless otherwise specified. Note 5: The algebraic convention, when the less positive (more negative) limit is designated minimum, is used in this data sheet for common mode input voltage and threshold voltage levels only. Note 6: Hysteresis is the difference between the positive-going input threshold voltage, VT+, and the negative going input threshold voltage, VT-. Note 7: Refer to EIA Standards RS-485 for exact conditions. Note 8: Only one output at a time should be shorted. www.national.com 2 VCC = 5V, TA = 25C Symbol tPLH tPHL Parameter Conditions Propagation Delay Time, VID = -2.5V to 2.5V, Low to High Level Output CL = 15 pF, Figure 1 Min Propagation Delay Time, Typ Max Units 15 25 ns 15 25 ns High to Low Level Output tPZH Output Enable Time to High Level CL = 15 pF, Figure 2 15 22 ns tPZL Output Enable Time to Low Level CL = 15 pF, Figure 3 15 22 ns tPHZ Output Disable Time from High Level CL = 5 pF, Figure 2 14 30 ns tPLZ Output Disable Time from Low Level CL = 5 pF, Figure 3 24 40 ns Function Tables (Each Receiver) DS96173 Differential Inputs Enables Outputs A-B E E V VID > 0.2V H X H X L H VID < -0.2V H X L X L L X L X Z X X H Z H = High Level L = Low Level X = Immaterial Z = High Impedance (off) (Each Receiver) DS96175 Differential Inputs Enable Output VID 0.2V H H VID -0.2V H L X L Z A-B Y Parameter Measurement Information 00962804 00962803 FIGURE 1. tPLH, tPHL (Note 11) 3 www.national.com DS96173/DS96175 Switching Characteristics DS96173/DS96175 Parameter Measurement Information (Continued) 00962806 00962805 FIGURE 2. tPHZ, tPZH (Note 11) 00962808 00962807 FIGURE 3. tPZL, tPLZ (Note 11) Note 9: The input pulse is supplied by a generator having the following characteristics: PRR = 1.0 MHz, 50% duty cycle, tr 6.0 ns, tf 6.0 ns, ZO = 50. Note 10: CL includes probe and stray capacitance. Note 11: DS96173 with active high and active low Enables is shown here. DS96175 has active high Enable only. Note 12: All diodes are 1N916 or equivalent. Note 13: To test the active low Enable E of DS96173, ground E and apply an inverted input waveform to E . DS96175 has active high Enable only. Typical Application 00962809 Note: The line length should be terminated at both ends in its characteristic impedance. Stub lengths off the main line should be kept as short as possible. FIGURE 4. www.national.com 4 inches (millimeters) Molded Dual-In-Line Package (N) Order Number DS96173CN or DS96175CN NS Package Number N16E National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. For the most current product information visit us at www.national.com. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. BANNED SUBSTANCE COMPLIANCE National Semiconductor certifies that the products and packing materials meet the provisions of the Customer Products Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain no ``Banned Substances'' as defined in CSP-9-111S2. National Semiconductor Americas Customer Support Center Email: new.feedback@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Customer Support Center Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 National Semiconductor Asia Pacific Customer Support Center Email: ap.support@nsc.com National Semiconductor Japan Customer Support Center Fax: 81-3-5639-7507 Email: jpn.feedback@nsc.com Tel: 81-3-5639-7560 DS96173/DS96175 RS-485/RS-422 Quad Differential Line Receivers Physical Dimensions unless otherwise noted IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated