COMX-CAR-610 - EMERSON�NETWORK POWER

Embedded Computing for

Business-Critical ContinuityTM

COMX-CAR-610 COM Express Carrier Board

Installation and Use

P/N: 6806800K26D

August 2011

Trademarks

Emerson, Business-Critical Continuity, Emerson Network Power and the Emerson Network Power logo are trademarks and service

owners.

Intel® is a trademark or registered trademark of Intel Corporation or its subsidiaries in the United States and other countries.

Java™ and all other Java-based marks are trademarks or registered trademarks of Sun Microsystems, Inc. in the U.S. and other

countries.

Microsoft®, Windows® and Windows Me® are registered trademarks of Microsoft Corporation; and Windows XP™ is a trademark of

Microsoft Corporation.

PICMG®, CompactPCI®, AdvancedTCA™ and the PICMG, CompactPCI and AdvancedTCA logos are registered trademarks of the PCI

Industrial Computer Manufacturers Group.

UNIX® is a registered trademark of The Open Group in the United States and other countries.

Notice

While reasonable efforts have been made to assure the accuracy of this document, Emerson assumes no liability resulting from any

omissions in this document, or from the use of the information obtained therein. Emerson reserves the right to revise this document

and to make changes from time to time in the content hereof without obligation of Emerson to notify any person of such revision or

changes.

Electronic versions of this material may be read online, downloaded for personal use, or referenced in another document as a URL to

a Emerson website. The text itself may not be published commercially in print or electronic form, edited, translated, or otherwise

altered without the permission of Emerson,

It is possible that this publication may contain reference to or information about Emerson products (machines and programs),

programming, or services that are not available in your country. Such references or information must not be construed to mean that

Emerson intends to announce such Emerson products, programming, or services in your country.

Limited and Restricted Rights Legend

If the documentation contained herein is supplied, directly or indirectly, to the U.S. Government, the following notice shall apply

unless otherwise agreed to in writing by Emerson.

Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (b)(3) of the Rights in

Technical Data clause at DFARS 252.227-7013 (Nov. 1995) and of the Rights in Noncommercial Computer Software and

Documentation clause at DFARS 252.227-7014 (Jun. 1995).

Contact Address

Emerson Network Power - Embedded Computing

2900 South Diablo Way, Suite 190

Tempe, AZ 85282

USA

Contents

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D) 3

About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

1.2 Standard Compliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

1.3 Mechanical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

1.4 Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

1.5 Product Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

2 Hardware Preparation and Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

2.1 Environmental and Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

2.1.1 Environmental Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

2.1.2 Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

2.2 Unpacking and Inspecting the Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

2.3 Installation and Removal of the COM Express Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

2.4 Replacing the Onboard Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

3 Controls, LEDs, and Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

3.1 Carrier Board Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

3.2 COM Express Board-to-Board Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

3.3 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

3.4 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

3.4.1 Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

3.4.1.1 LVDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

3.4.1.2 VGA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

3.4.1.3 HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

3.4.1.4 Display Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

3.4.2 Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

3.4.3 LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

3.4.4 PCI Express . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

3.4.5 USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

3.4.5.1 USB 2.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

3.4.5.2 USB 3.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

3.4.6 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Contents

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)

Contents

3.4.7 Super I/O. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

3.4.7.1 Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

3.4.7.2 PS/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

3.4.7.3 LPT Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

3.4.7.4 Serial Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

3.4.8 Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

3.5 Headers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

3.5.1 LPC. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

3.5.2 Trusted Platform Module (TPM). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

3.5.3 GPIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

3.5.4 Miscellaneous I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

3.5.5 SPI Flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

3.5.6 EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

4.1 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

4.2 Video . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

4.2.1 LVDS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

4.2.2 VGA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

4.2.3 HDMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

4.2.4 Display Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

4.3 Audio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

4.4 LAN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

4.5 PCI Express . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

4.5.1 PCI Express Mini Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

4.6 USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

4.7 Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

4.8 Super I/O . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

4.8.1 Voltage and Thermal Monitoring. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

4.8.2 Fan Control. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

4.8.3 PS/2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

4.8.4 LPT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

4.8.5 RS-232 and RS-422/485 Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

4.9 SPI Flash . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

4.10 Watchdog Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Contents

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D) 5

4.11 Real Time Clock (RTC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

4.12 Wake Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

A Related Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

A.1 Emerson Network Power—Embedded Computing Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

A.2 Manufacturers’ Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Safety Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Sicherheitshinweise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)

Contents

List of Tables

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D) 7

Table 1-1 Carrier Board Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Table 1-2 Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Table 2-1 Environmental Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Table 2-2 Carrier Board Power Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Table 2-3 Current Requirements from the Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Table 3-1 COM Express Connector Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Table 3-2 LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Table 3-3 P8, Backlight Wafer Header Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Table 3-4 P6, LVDS Connector Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Table 3-5 P7, LVDS Power Supply Jumper Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Table 3-6 P35, LVDS Power Supply Jumper Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Table 3-7 J5, VGA Connector Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Table 3-8 J5, HDMI Connector Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Table 3-9 J3 and J4, Display Port Connector Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Table 3-10 J16, Audio Jack Connector Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Table 3-11 P11, Audio Header Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Table 3-12 J1, LAN Connector Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Table 3-13 P9 Jumper Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Table 3-14 P24 Jumper Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Table 3-15 P25 Jumper Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Table 3-16 P2, USB 2.0 Header Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Table 3-17 P1, USB 2.0 Header Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Table 3-18 P39, USB 2.0 Header Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Table 3-19 P10, Jumper Settings for Configuring USB Multiplexed Devices . . . . . . . . . . . . . . . . . . . 40

Table 3-20 J14 and J15, USB 3.0 Connector Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Table 3-21 P10—P13, SATA Socket Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Table 3-22 P3 and P27, Fan Header Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Table 3-23 P26, PS/2 (Keyboard and Mouse) Connectors Pin Definition . . . . . . . . . . . . . . . . . . . . . . 42

Table 3-24 P32, LPT Header Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Table 3-25 P18—P23, RS-232 Headers Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Table 3-26 P37 and P33, RS-422/RS-485 Headers Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Table 3-27 Set Jumpers P34 and P41 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Table 3-28 P40 PS_ON Select Jumper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Table 3-29 ATX Power Supply Connector Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Table 3-30 P29, Low Pin Count (LPC) Header Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Table 3-31 P28, Trusted Platform Module (TPM) Header Pin Definition . . . . . . . . . . . . . . . . . . . . . . . 45

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)

List of Tables

Table 3-32 P30, GPIO Header Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Table 3-33 P16, Miscellaneous I/O Header Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Table 3-34 P13, SPI Flash Header Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Table 3-35 P12 and P14, Jumper Settings for SPI Flash SF100 header . . . . . . . . . . . . . . . . . . . . . . . . . 47

Table 3-36 P15 and P38, Jumper Configuration to Enable/Disable BIOS . . . . . . . . . . . . . . . . . . . . . . . 47

Table 3-37 P17 Case Open Select Header . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Table 3-38 P31, EEPROM Header Pin Definition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Table 4-1 Wake Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Table A-1 Emerson Network Power, Embedded Computing Publications . . . . . . . . . . . . . . . . . . . . 59

List of Figures

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D) 9

Figure 1-1 Standard Compliances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Figure 1-2 COMX-CORE Series Mechanical Dimensions (Top View) . . . . . . . . . . . . . . . . . . . . . . 18

Figure 1-3 COMX-CORE Series Mechanical Dimensions (SideView) . . . . . . . . . . . . . . . . . . . . . . 19

Figure 1-4 Location of Product Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Figure 3-1 COMX-CAR-610 COM Express Carrier Board Component Layout . . . . . . . . . . . . . . . 27

Figure 4-1 COM Express Type 6 Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Figure 4-2 PCI Express Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Figure 4-3 PCI Express Mini Card Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Figure 4-4 Super I/O Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Figure 4-5 SPI Flash Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Figure 4-6 Watchdog Timer Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)

List of Figures

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D) 11

About this Manual

Overview of Contents

This manual is divided into the following chapters and appendices:

Introduction provides an overview of the product’s features.

Hardware Preparation and Installation provides instructions on installing and removing the

module.

Controls, LEDs, and Connectors provides information on the pin assignments of the various

connectors on the board.

Functional Description discusses the functions of various components on the board.

BIOS discusses the functions that are available on the Setup Utility.

Related Documentation lists various documentation relevant to the product.

Safety Notes provides a summary of the safety notices applicable to the product.

Sicherheitshinweise is a German version of the Safety Notes.

Abbreviations

This document uses the following abbreviations:

Abbreviation Definition

ACPI Advanced Configuration Power Interface

AMC Alarm Management Controller

ARP Address Resolution Protocol

BDS Boot Device Selection

DDR Double Data Rate

DXE Driver Execution Environment

EEPROM Electrically Erasable Programable Read-Only Memory

eUSB Embedded Universal Serial Bus

GbE Gigabit Ethernet

GPIO General Purpose Input Output

HDMI High-Definition Multimedia Interface

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)

About this Manual

I2C Inter-Integrated Circuit

I/O Input/Output

IDE Integrated Device Electronics

LED Light Emitting Diode

LIN Line In

LFM Linear Feet per Minute

LPT Line Print Terminal

LOUT Line Out

LDVS Low Voltage Differential Signaling

MICIN Microphone In

NVRAM Non-volatile RAM

OEM Original Equipment Manufacturer

PCI Peripheral Component Interconnect

PCI-E Peripheral Component Interconnect Express

POST Power-on Self Test

RTC Real Time Clock

SATA Serial AT Attachment

SCSI Small Computer System Interface

SPD Serial Presence Detect

SPI Serial Peripheral Interface

SODIMM Small Outline Dual In-line Memory Module

Super I/O Super Input/Output

TPM Trusted Platform Module

USB Universal Serial Bus

VGA Video Graphics Adapter

WDT Watchdog Timer

Abbreviation Definition

About this Manual

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D) 13

Conventions

The following table describes the conventions used throughout this manual.

Notation Description

0x00000000 Typical notation for hexadecimal numbers (digits are

0 through F), for example used for addresses and

offsets

0b0000 Same for binary numbers (digits are 0 and 1)

bold Used to emphasize a word

Screen Used for on-screen output and code related elements

or commands in body text

Courier + Bold Used to characterize user input and to separate it

from system output

Reference Used for references and for table and figure

descriptions

File > Exit Notation for selecting a submenu

<text> Notation for variables and keys

[text] Notation for software buttons to click on the screen

and parameter description

... Repeated item for example node 1, node 2, ..., node

Omission of information from example/command

that is not necessary at the time being

.. Ranges, for example: 0..4 means one of the integers

0,1,2,3, and 4 (used in registers)

|Logical OR

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)

About this Manual

Summary of Changes

This manual has been revised and replaces all prior editions.6806800K26B

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury

Indicates a hazardous situation which, if not avoided,

may result in minor or moderate injury

Indicates a property damage message

No danger encountered. Pay attention to important

information

Notation Description

Part Number Publication Date Description

6806800A36C January 2006 First edition

6806800K26B March 2010 GA Version

6806800K26C November 2010 GA version: Updated Section 3.4.4 PCI Express

6806800K26D September 2011 Updated Table "P12 and P14, Jumper Settings for

SPI Flash SF100 header" on page 47, Table "P15

and P38, Jumper Configuration to Enable/Disable

BIOS" on page 47.

Added Table "P17 Case Open Select Header" on

page 48 and Table "P40 PS_ON Select Jumper" on

page 44.

Chapter 1

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D) 15

Introduction

1.1 Features

The COMX-CAR-610 COM Express Carrier Board is a Type 6 carrier board. This board is designed

to support the COM Express Type 6 Specification and is compatible with COM Express Type 1

Specification. This board supports the following COM Express form factors: compact, basic,

and extended.

Table 1-1 Carrier Board Features

Feature Description

Form factor MicroATX (9.6'' x 9.6'')

Video One backlight header for powering a backlight

One LVDS connector

Two Display Port connectors

One VGA and HDMI connector

Audio One audio jack: MICIN,LOUT,LIN

One audio header: MICIN, LOUT

Clock buffer 33 MHz clock buffer: ICS9112AM-16

100 MHz clock buffer: ICS9DB108BFLF

LPT One LPT header from Super I/O

KBMS One keyboard and mouse header

COM Four RS-232 ports (COM1—COM4)

Two RS-232/RS-422/RS-485 ports (COM5 and COM6)

LAN LAN1—GbE from COM Express module

LAN2—GbE from carrier board (WG82574L)

USB Four USB3.0 ports

Three USB 2.0 ports (in header)

One eUSB flash (maximum of 8 GB)

PCI-E Slots One PCI-E x16 slot

Two PCI-E x4 slots

One PCI-E x1 slot

PCI-E Minicard One PCI-E Mini-Card for WiFi or WiMax

Serial ATA Four SATA II ports

Introduction

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)

Trusted Platform Module One onboard TPM header

Power supply One 24-pin ATX power header

One 4-pin ATX_12V header

One battery socket

Hardware Monitor and Controller Three-channel voltage sensors: 5 V, 3.3 V and 12 V

Two-channel temperature sensors: module and system

Two-channel Fan speed Control: Module and system

Supported COM Express Form

Factors

Compact

Basic

Extended

Wake-Up Events Power Button: S0, S3, S4, S5

KB: S0, S3

Mouse: S0, S3

PME: S0, S3, S4, S5

USB: S0, S3

Wake on LAN support

Table 1-1 Carrier Board Features (continued)

Feature Description

Introduction

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D) 17

1.2 Standard Compliances

Figure 1-1 Standard Compliances

Introduction

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)

1.3 Mechanical Data

Figure 1-2 COMX-CORE Series Mechanical Dimensions (Top View)

Introduction

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D) 19

1.4 Ordering Information

Figure 1-3 COMX-CORE Series Mechanical Dimensions (SideView)

Table 1-2 Ordering Information

Orderable Number Description

COMX-CAR-610 Type 6 COM express carrier board UATX

Introduction

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)

1.5 Product Identification

The following figure shows the location of the board’s serial number.

Figure 1-4 Location of Product Serial Number

Chapter 2

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D) 21

Hardware Preparation and Installation

2.1 Environmental and Power Requirements

You must make sure that the board, when operated in your particular system configuration,

meets the environmental requirements specified below.

2.1.1 Environmental Requirements

Operating temperatures refer to the temperature of the air circulating around the board and

not to the component temperature.

Product Damage

High humidity and condensation on surfaces cause short circuits.

Do not operate the system outside the specified environmental limits. Make sure the

product is completely dry and there is no moisture on any surface before applying

power.

Table 2-1 Environmental Requirements

Environmental Factor Operating Non-Operating

Temperature 0 to +55°C -40 to +85°C

Shock 20 g 11 ms sine or saw

Vibration 0.01g ^2/Hz at 5-500 Hz Random

Vibration

Air Flow 400 LFM at 0 to 55°C

Humidity 10-90% (non-condensing)

Hardware Preparation and Installation

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)

2.1.2 Power Requirements

The following table shows the power consumption of the carrier board without a COM Express

module installed.

Note: Including 120W power dissipation for COM-E module.

The following table lists the onboard voltages that the DC input generates. The table also

provides an estimate of the typical and maximum current required from the power supply.

Table 2-2 Carrier Board Power Consumption

Item

+5.0V

POWER

+3.3V

POWER +12V POWER 5V SB POWER TOTAL POWER

Power 50W 6W 160W 10W 240W Max

Table 2-3 Current Requirements from the Power Supply

Supply Voltage Source Voltage Maximum Current

VCC12 ATX power 12 V 13 A

VCC5 ATX power 5 V 10 A

VCC3 ATX power 3 V 2 A

VCC1_5 VCC3 1.5 V 0.5 A

5VSB ATX power 5 V 2 A

5VDual VCC1_5 and 5VSB 5 V 10 A

3VDual VCC3 and 5VSB 3 V 1 A

VCC1_8 VCC3 1.8 V 0.5 A

Hardware Preparation and Installation

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D) 23

2.2 Unpacking and Inspecting the Board

1. Verify that you have received all items of your shipment:

Printed Quick Start Guide and Safety Notes

COMX-CAR-610 COM Express Carrier Board

Accessories:

— Cable, URAT, 2X5PIN housing to DB9PIN connector, with I/O panel, 300MM

length

— Cable, USB, 2X5PIN housing to USB X 2 connector, with I/O panel, 300MM

length

— Cable, LPT, 2X13PIN housing to DB25 PIN connector, with I/O panel,

300MM length

— Cable, PS/2, MINI DIN6P to PS/2 connector, 300MM length

— COMX-CAR-610 Carrier Board I/O Shield

Damage of Circuits

Electrostatic discharge and incorrect installation and removal of the product can

damage circuits or shorten its life.

Before touching the product make sure that you are working in an ESD-safe

environment or wearing an ESD wrist strap or ESD shoes. Hold the product by its edges

and do not touch any components or circuits.

Hardware Preparation and Installation

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)

2. Check for damage and report any damage or differences to customer service.

3. Remove the desiccant bag shipped together with the product.

2.3 Installation and Removal of the COM Express

Module

The assembled COM Express module with the attached heat spreader is attached to a carrier

board.

Installing the COM Express Module on the Carrier Board

1. Line up the board-to-board connector of the COM Express module with the board-

to-board connector of the COMX-CAR-610.

2. Make sure that the interconnectors are properly aligned and that the seven

standoffs have contact with the top of the COMX-CAR-610.

3. Turn over the COM Express module and the COMX-CAR-610.

4. From the backside of the COMX-CAR-610, locate the screw holes.

5. Use the screws to fasten the COM Express module assembly to the COMX-CAR-

610.

Environmental Damage

Improper disposal of used products may harm the environment.

Always dispose of used products according to your country’s legislation and

manufacturer’s instructions.

Hardware Preparation and Installation

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D) 25

Removing the COM Express Module from the Carrier Board

1. Turn over the COM Express module and the COMX-CAR-610.

2. On the back of the COMX-CAR-610, locate the seven screws that connect the

COM Express module to the COMX-CAR-610.

3. Loosen and remove the screws.

4. While holding the edges, pull the COM Express module from the COMX-CAR-610.

Hardware Preparation and Installation

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)

2.4 Replacing the Onboard Battery

1. Remove the old battery.

2. Install the new battery with the plus sign (+) facing up.

3. Dispose of the old battery according to your country’s legislation and in an

environmentally safe way.

Product Damage

Incorrect replacement of lithium batteries can result in a hazardous explosion.

When exchanging the on-board lithium battery, make sure that the new and the old

battery are exactly the same battery models.

If the respective battery model is not available, contact your local Emerson sales

representative for the availability of alternative officially approved battery models.

PCB and Battery Holder Damage

Removing the battery with a screw driver may damage the PCB or the battery holder.

Do not use a screw driver to remove the battery from its holder.

Data Loss

Installing another battery type than the one that is mounted at product delivery may

cause data loss since other battery types may be specified for other environments or

may have a shorter lifetime.

Only use the same type of lithium battery as is already installed.

Chapter 3

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D) 27

Controls, LEDs, and Connectors

3.1 Carrier Board Layout

Figure 3-1 COMX-CAR-610 COM Express Carrier Board Component Layout

Controls, LEDs, and Connectors

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)

3.2 COM Express Board-to-Board Connector

This section details the pin assignments on the COM Express connector based on the Type 6

Specification.

Table 3-1 COM Express Connector Pin Definition

Row A B C D

1 GND(FIXED) GND (FIXED) GND (FIXED) GND (FIXED)

2 GBE0_MDI3- GBE0_ACT# GND GND

3 GBE0_MDI3+ LPC_FRAME# USB0_SSRX- USB0_SSTX-

4 GBE0_LINK100# LPC_AD0 USB0_SSRX+ USB0_SSTX+

5 GBE0_LINK1000# LPC_AD1 GND GND

6 GBE0_MDI2- LPC_AD2 USB1_SSRX- USB1_SSTX-

7 GBE0_MDI2+ LPC_AD3 USB1_SSRX+ USB1_SSTX+

8 GBE0_LINK# LPC_DRQ0# GND GND

9 GBE0_MDI1- LPC_DRQ1# USB2_SSRX- USB2_SSTX-

10 GBE0_MDI1+ LPC_CLK USB2_SSRX+ USB2_SSTX+

11 GND(FIXED) GND(FIXED) GND(FIXED) GND(FIXED)

12 GBE0_MDI0- PWRBTN# USB3_SSSRX- USB3_SSTX-

13 GBE0_MDI0+ SMB_CK USB3_SSRX+ USB3_SSTX+

14 GBE0_CTREF SMB_DAT GND GND

15 SUS_S3# SMB_ALERT# DDI1_PAIR6+ DDI1_AUX+

16 SATA0_TX+ SATA1_TX+ DDI1_PAIR6- DDI1_AUX-

17 SATA0_TX- SATA1_TX- RSVD RSVD

18 SUS_S4# SUS_STAT# RSVD RSVD

19 SATA0_RX+ SATA1_RX+ PCIE_RX6+ PCIE_TX6+

20 SATA0_RX- SATA1_RX- PCIE_RX6- PCIE_TX6-

21 GND(FIXED) GND(FIXED) GND(FIXED) GND(FIXED)

22 SATA2_TX+ SATA3_TX+ PCIE_RX7+ PCIE_TX7+

23 SATA2_TX- SATA3_TX- PCIE_RX7- PCIE_TX7-

Controls, LEDs, and Connectors

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D) 29

24 SUS_S5# PWR_OK DDI1_HPD RSVD

25 SATA2_RX+ SATA3_RX+ DDI1_PAIR4+ RSVD

26 SATA2_RX- SATA3_RX- DDI1_PAIR4- DDI1_PAIR0+

27 BATLOW# WDT RSVD DDI1_PAIR0-

28 ATA_ACT# AC/HDA_SDIN2 RSVD RSVD

29 AC/HDA_SYNC AC/HDA_SDIN1 DDI1_PAIR5+ DDI1_PAIR1+

30 AC/HDA_RST# AC/HDA_SDIN0 DDI1_PAIR5- DDI1_PAIR1-

31 GND(FIXED) GND(FIXED) GND(FIXED) GND(FIXED)

32 AC/HDA_BITCLK SPKR DDI2_AUX+ DDI1_PAIR2+

33 AC/HDA_SDOUT I2C_CK DDI2_AUX- DDI1_PAIR2-

34 BIOS_DISABLE# I2C_DAT DDI2_CTRLCLK DDI2_CTRLDATA

35 THRMTRIP# THRM# RSVD RSVD

36 USB6- USB7- DDI3_AUX+ DDI1_PAIR3+

37 USB6+ USB7+ DDI3_AUX- DDI1_PAIR3-

38 USB_6_7_OC# USB_4_5_OC# DDI3_CTRLCLK DDI3_CTRLDATA

39 USB4- USB5- DDI3_PAIR0+ DDI2_PAIR0+

40 USB4+ USB5+ DDI3_PAIR0- DDI2_PAIR0-

41 GND(FIXED) GND(FIXED) GND(FIXED) GND(FIXED)

42 USB2- USB3- DDI3_PAIR0+ DDI2_PAIR1+

43 USB2+ USB3+ DDI3_PAIR0- DDI2_PAIR1-

44 USB_2_3_OC# USB_0_1_OC# DDI3_HPD DDI2_HPD

45 USB0- USB1- RSVD RSVD

46 USB0+ USB1+ DDI3_PAIR2+ DDI2_PAIR2+

47 VCC_RTC EXCD1_PERST# DDI3_PAIR2- DDI2_PAIR2-

48 EXCD0_PERST# EXCD1_CPPE# RSVD RSVD

49 EXCD0_CPPE# SYS_RESET# DDI3_PAIR3+ DDI2_PAIR3+

50 LPC_SERIRQ CB_RESET# DDI3_PAIR3- DDI2_PAIR3-

Table 3-1 COM Express Connector Pin Definition (continued)

Row A B C D

Controls, LEDs, and Connectors

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)

51 GND(FIXED) GND(FIXED) GND(FIXED) GND(FIXED)

52 PCIE_TX5+ PCIE_RX5+ PEG_RX0+ PEG_TX0+

53 PCIE_TX5- PCIE_RX5- PEG_RX0- PEG_TX00-

54 GPI0 GPO1 TYPE0# PEG_LANE_RV#

55 PCIE_TX4+ PCIE_RX4+ PEG_RX1+ PEG_TX1+

56 PCIE_TX4- PCIE_RX4- PEG_RX1- PEG_TX1-

57 GND GPO2 TYPE1# TYPE2#

58 PCIE_TX3+ PCIE_RX3+ PEG_RX2+ PEG_TX2+

59 PCIE_TX3- PCIE_RX3- PEG_RX2- PEG_TX2-

60 GND(FIXED) GND(FIXED) GND(FIXED) GND(FIXED)

61 PCIE_TX2+ PCIE_RX2+ PEG_RX3+ PEG_TX3+

62 PCIE_TX2- PCIE_RX2- PEG_RX3- PEG_TX3-

63 GPI1 GPO3 RSVD RSVD

64 PCIE_TX1+ PCIE_RX1+ RSVD RSVD

65 PCIE_TX1- PCIE_RX1- PEG_RX4+ PEG_TX4+

66 GND WAKE0# PEG_RX4- PEG_TX4-

67 GPI2 WAKE1# RSVD GND

68 PCIE_TX0+ PCIE_RX0+ PEG_RX5+ PEG_TX5+

69 PCIE_TX0- PCIE_RX0- PEG_RX5- PEG_TX5-

70 GND(FIXED) GND(FIXED) GND(FIXED) GND(FIXED)

71 LVDS_A0+ LVDS_B0+ PEG_RX6+ PEG_TX6+

72 LVDS_A0- LVDS_B0- PEG_RX6- PEG_TX6-

73 LVDS_A1+ LVDS_B1+ DDI1_CTRLDATA DDI1_CTRLCLK

74 LVDS_A1- LVDS_B1- PEG_RX7+ PEG_TX7+

75 LVDS_A2+ LVDS_B2+ PEG_RX7- PEG_TX7-

76 LVDS_A2- LVDS_B2- GND GND

77 LVDS_VDD_EN LVDS_B3+ RSVD IDE_CBLID#

Table 3-1 COM Express Connector Pin Definition (continued)

Row A B C D

Controls, LEDs, and Connectors

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D) 31

78 LVDS_A3+ LVDS_B3- PEG_RX8+ PEG_TX8+

79 LVDS_A3- LVDS_BKLT_EN PEG_RX8- PEG_TX8-

80 GND(FIXED) GND(FIXED) GND(FIXED) GND(FIXED)

81 LVDS_A_CK+ LVDS_B_CK+ PEG_RX9+ PEG_TX9+

82 LVDS_A_CK- LVDS_B_CK- PEG_RX9- PEG_TX9-

83 LVDS_I2C_CK LVDS_BKLT_CTRL RSVD RSVD

84 LVDS_I2C_DAT VCC_5V_SBY GND GND

85 GPI3 VCC_5V_SBY PEG_RX10+ PEG_TX10+

86 KBD_RST# VCC_5V_SBY PEG_RX10- PEG_TX10-

87 KBD_A20GATE VCC_5V_SBY GND GND

88 PCIE0_CK_REF+ RSVD PEG_RX11+ PEG_TX11+

89 PCIE0_CK_REF- VGA_RED PEG_RX11- PEG_TX11-

90 GND(FIXED) GND(FIXED) GND(FIXED) GND(FIXED)

91 SPI_CS0# VGA_GRN PEG_RX12+ PEG_TX12+

92 SPI_MISO VGA_BLU PEG_RX12- PEG_TX12-

93 GPO0 VGA_HSYNC GND GND

94 SPI_CLK VGA_VSYNC PEG_RX13+ PEG_TX13+

95 SPI_MOSI VGA_I2C_CK PEG_RX13- PEG_TX13-

96 GND VGA_I2C_DAT GND GND

97 VCC_12V RSVD RSVD PEG_ENABLE#

98 VCC_12V RSVD PEG_RX14+ PEG_TX14+

99 VCC_12V RSVD PEG_RX14- PEG_TX14-

100 GND(FIXED) GND(FIXED)GND(FIXED)GND(FIXED)

101 VCC_12V VCC_12V PEG_RX15+ PEG_TX15+

102 VCC_12V VCC_12V PEG_RX15- PEG_TX15-

103 VCC_12V VCC_12V GND GND

104 VCC_12V VCC_12V VCC_12V VCC_12V

Table 3-1 COM Express Connector Pin Definition (continued)

Row A B C D

Controls, LEDs, and Connectors

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)

3.3 LEDs

105 VCC_12V VCC_12V VCC_12V VCC_12V

106 VCC_12V VCC_12V VCC_12V VCC_12V

107 VCC_12V VCC_12V VCC_12V VCC_12V

108 VCC_12V VCC_12V VCC_12V VCC_12V

109 VCC_12V VCC_12V VCC_12V VCC_12V

110 GND(FIXED) GND(FIXED)GND(FIXED)GND(FIXED)

Table 3-1 COM Express Connector Pin Definition (continued)

Row A B C D

Table 3-2 LEDs

States Location Description

S0 D20 ON: System is full on

S3 D22 ON: System is suspended to memory

S4 D24 ON: System is hybernating

S5 D23 ON: System is off

System PWROK D21 ON: All system power is OK

Type6 Error D34 ON: Module does not comply with Type 6

spec

Thermal Trip D26 ON: CPU is hot; system needs to be shut

down

Suspend Status D28 ON: Suspend Status

Mini-CD SW OK D37 ON: USB and PCI-E have both switched to

mini PCI-E slot

Controls, LEDs, and Connectors

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D) 33

3.4 Connectors

3.4.1 Video

3.4.1.1 LVDS

Table 3-3 P8, Backlight Wafer Header Pin Definition

Pin Signal

112V

2BKLT_EN

3GND

4BKLT_CTRL

55V

Table 3-4 P6, LVDS Connector Pin Definition

Pin Signal Pin Signal

1 LVDSA_DATA0_P 2 LVDSB_DATA0_P

3 LVDSA_DATA0_N 4 LVDSB_DATA0_N

7 LVDSA_DATA1_P 8 LVDSB_DATA1_P

9 LVDSA_DATA1_N 10 LVDSB_DATA1_N

13 LVDSA_DATA2_P 14 LVDSB_DATA2_P

15 LVDSA_DATA2_N 16 LVDSB_DATA2_N

19 LVDSA_DATA3_P 20 LVDSB_DATA3_P

21 LVDSA_DATA3_N 22 LVDSB_DATA3_N

25 LVDSA_CLK_P 26 LVDSB_CLK_P

27 LVDSA_CLK_N 28 LVDSB_CLK_N

31 LVDS_I2C_CLK 32 LVDS_I2C_DATA

Controls, LEDs, and Connectors

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)

The 3 V or 5 V DC LVDS power supply is configured through the 3-pin jumper P7.

The 12 V DC LVDS power supply is configured through the 3-pin header P35

3.4.1.2 VGA

33,35,37,39 VDD (3.3V OR 5V) 36,38,40 VDD (12V)

11,17,23,29

GND 6,12,18,24,3

0,34

GND

Table 3-5 P7, LVDS Power Supply Jumper Configuration

Jumper Setting Configuration

P7 (1-2) 3.3V (Default)

P7 (2-3) 5V

Table 3-6 P35, LVDS Power Supply Jumper Configuration

Jumper Setting Configuration

P35 (1-2) 12V

P35 (2-3) NC (Default)

Table 3-4 P6, LVDS Connector Pin Definition (continued)

Pin Signal Pin Signal

Table 3-7 J5, VGA Connector Pin Definition

Pin Signal Pin Signal

V1 CRT_R V2 CRT_G

V3 CRT_B V4 NC

V5 GND V6 GND

V7 GND V8 GND

V9 5V V10 GND

Controls, LEDs, and Connectors

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D) 35

3.4.1.3 HDMI

3.4.1.4 Display Port

V11 NC V12 DDCDATA

V13 HSYNC V14 VSYNC

V15 DDCCLK

Table 3-7 J5, VGA Connector Pin Definition (continued)

Pin Signal Pin Signal

Table 3-8 J5, HDMI Connector Pin Definition

Pin Signal Pin Signal

H1 OUT_D2+ H2 GND

H3 OUT_D2- H4 OUT_D1+

H5 GND H6 OUT_D1-

H7 OUT_D0+ H8 GND

H9 OUT_D0- H10 TLC

H11 GND H12 TLC-

H13 NC H14 NC

H15 SCL_IN H16 SDA_IN

H17 GND H18 5V

H19 HPD_IN

Table 3-9 J3 and J4, Display Port Connector Pin Definition

Pin Signal

1DP_0_P

3DP_0_N

Controls, LEDs, and Connectors

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)

3.4.2 Audio

4DP_1_P

6DP_1_N

7DP_2_P

9DP_2_N

10 DP_3_P

12 DP_3_N

13 DP_AUX_EN_N

15 DP_AUX_P

17 DP_AUX_N

18 DP_HPD

20 VCC_3

2,5,8,11,14,16,19 GND

Table 3-9 J3 and J4, Display Port Connector Pin Definition (continued)

Pin Signal

Table 3-10 J16, Audio Jack Connector Pin Definition

Pin Signal Pin Signal

A1 LIN_L A2 LIN_JD

A3 AGND A4 LIN_R

B1 LOUT_L B2 LOUT_JD

B3 AGND B4 LOUT_R

C0 AGND C1 MIC1L

C2 MIC1_JD C3 AGND

C4 MIC1R MH1~MH4 AGND

Controls, LEDs, and Connectors

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D) 37

3.4.3 LAN

Table 3-11 P11, Audio Header Pin Definition

Pin Signal Pin Signal

1MIC2_L 2 GND

3MIC2_R 4 NC

5LOUT2_R 6 MIC2_JD

7GND 8 KEY

9 LOUT2_L 10 LOUT2_JD

Table 3-12 J1, LAN Connector Pin Definition

Pin Signal Pin Signal

1NC 141.8V

2 LAN1_MID3_N 15 LAN2_MID0_P

3 LAN1_MID2_P 16 LAN2_MID1_N

4 GBE0_CTREF 17 1.8V

5 LAN1_MID1_N 18 LAN2_MID2_P

6 LAN1_MID0_P 19 LAN2_MID3_N

7 GBE0_CTREF 20 GND

8 LAN1_MID3_P 21 LAN2_MID0_N

9 GBE0_CTREF 22 1.8V

10 LAN1_MID2_N 23 LAN2_MID1_P

11 LAN1_MID1_P 24 LAN2_MID2_N

12 GBE0_CTREF 25 1.8V

13 LAN1_MID0_N 26 LAN2_MID3_P

31 LAN1_LED_LINK_N 27 LAN2_LED_LINK_N

32 LAN1_LED_LINK_P 28 LAN2_LED_LINK_P

33 LAN1_LED_ACT_N 29 LAN2_LED_ACT_N

Controls, LEDs, and Connectors

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)

3.4.4 PCI Express

Jumpers P9, P24, and P25 are used to configure PCI Express multiplexed devices.

34 LAN1_LED_ACT_P 30 LAN2_LED_ACT_P

Table 3-12 J1, LAN Connector Pin Definition (continued)

Pin Signal Pin Signal

Table 3-13 P9 Jumper Setting

Jumper Setting Configuration

P9 (1-2) x4 PCI-E slot

P9 (2-3) x1 PCI-E slot (Default)

Table 3-14 P24 Jumper Setting

Jumper Setting Configuration

P24 (1-2) x4 PCI-E slot

P24 (2-3) PCI-E Mini Card (Default)

Table 3-15 P25 Jumper Setting

Jumper Setting Configuration

P25 (1-2) x4 PCI-E slot

P25 (2-3) LAN (Default)

Controls, LEDs, and Connectors

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D) 39

3.4.5 USB

3.4.5.1 USB 2.0

P1, a USB 2.0 header could be used for eUSB flash applications.

P39, another USB 2.0 header could be used for PCI Express Mini Card applications.

Table 3-16 P2, USB 2.0 Header Pin Definition

Pin Signal Pin Signal

15VDUAL 25VDUAL

3 USB1 _N 4 USB2_N

5USB1_P 6USB2_P

7GND 8GND

9NC 10Key

Table 3-17 P1, USB 2.0 Header Pin Definition

Pin Signal Pin Signal

15VDUAL 2 5VDUAL

3USB _N 4 NC

5USB_P 6 NC

7GND 8 GND

9NC 10 Key

Table 3-18 P39, USB 2.0 Header Pin Definition

Pin Signal Pin Signal

15VDUAL 2NC

3USB _N 4NC

Controls, LEDs, and Connectors

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)

You need to set a 3-pin jumper (P10) if you want to configure USB multiplexed devices.

3.4.5.2 USB 3.0

5USB_P 6NC

7GND 8GND

9NC 10Key

Table 3-19 P10, Jumper Settings for Configuring USB Multiplexed Devices

Jumper Setting Configuration

P10 (1-2) USB 2.0 onboard

P10 (2-3) Mini Card (Default)

Table 3-18 P39, USB 2.0 Header Pin Definition (continued)

Pin Signal Pin Signal

Table 3-20 J14 and J15, USB 3.0 Connector Pin Definition

Pin Signal Pin Signal

15V 2 USB_P0 _N

3USB_P0 _P 4 GND

5 USB0_SSRX _N 6 USB0_SSRX _P

7GND 8 USB0_SSTX _N

9 USB0_SSTX _P 10 5V

11 USB_P1 _N 12 USB_P1 _P

13 GND 14 USB1_SSRX_N

15 USB1_SSRX _P 16 GND

17 USB1_SSTX _N 18 USB1_SSTX _P

Controls, LEDs, and Connectors

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D) 41

3.4.6 Storage

3.4.7 Super I/O

3.4.7.1 Fan

Table 3-21 P10—P13, SATA Socket Pin Definition

Pin Signal

1GND

2SATA_TX_P

3SATA_TX_N

4GND

5SATA_RX_N

6SATA_RX_P

7GND

Table 3-22 P3 and P27, Fan Header Pin Definition

Pin Signal

1GND

212V

3TACH

4PWM

Controls, LEDs, and Connectors

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)

3.4.7.2 PS/2

3.4.7.3 LPT Port

Table 3-23 P26, PS/2 (Keyboard and Mouse) Connectors Pin Definition

Pin Signal

15V

2KB_DATA

3KB_CLK

4MS_DATA

5MS_CLK

6GND

Table 3-24 P32, LPT Header Pin Definition

Pin Signal Pin Signal

1STB_N 2 PD0

3PD1 4 PD2

5PD3 6 PD4

7PD5 8 PD6

9PD7 10 ACK_N

11 BUSY_N 12 PE_N

13 SLCT_N 14 AFD_N

15 ERR_N 16 INIT_N

17 SLIN_N 18—25 GND

26 Key

Controls, LEDs, and Connectors

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D) 43

3.4.7.4 Serial Ports

You need to set jumpers P34 and P41 to configure the serial ports defined above as RS-232 or

RS-422/485 ports.

Table 3-25 P18—P23, RS-232 Headers Pin Definition

Pin Signal Pin Signal

1DCD_N 2RXD

3TXD 4DTR

5GND 6DSR_N

7 RTS_N 8 CTS_N

9RI_N 10Key

Table 3-26 P37 and P33, RS-422/RS-485 Headers Pin Definition

Pin Signal

1 RS422_RX_N

2 RS422_RX_P

3 RS422_TX_N/RS485_N

4 RS422_TX_P/RS485_P

Table 3-27 Set Jumpers P34 and P41

Jumper Setting Configuration

P34/P41 (1-2) RS232 (Default)

P34/P41 (3-4) RS422

P34/P41 (5-6) RS485

Controls, LEDs, and Connectors

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)

3.4.8 Power

3.5 Headers

3.5.1 LPC

Table 3-28 P40 PS_ON Select Jumper

Jumper Setting Configuration

P40 (1-2) Powe on through SIO (Default)

P40 (2-3) S3 and Type VI

Table 3-29 ATX Power Supply Connector Pin Definition

Pin Signal

1GND

2GND

3+12V

4+12V

Table 3-30 P29, Low Pin Count (LPC) Header Pin Definition

Pin Signal

1 CLK_33M

2AD1

3RST_N

4AD0

5FRAME_N

63.3V

Controls, LEDs, and Connectors

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D) 45

3.5.2 Trusted Platform Module (TPM)

3.5.3 GPIO

7AD3

8GND

9AD2

Table 3-30 P29, Low Pin Count (LPC) Header Pin Definition (continued)

Pin Signal

Table 3-31 P28, Trusted Platform Module (TPM) Header Pin Definition

Pin Signal Pin Signal

1CLK_33M2 GND

3FRAME_N4 NC

5RST_N 6 5V

7AD3 8 AD2

93.3V 10AD1

11 AD0 12 GND

13 SMB_CLK 14 SMB_DATA

15 3VDUAL 16 INT_SERIRQ

17 GND 18 CLKRUN_N

19 3.3V 20 DRQ0_N

Table 3-32 P30, GPIO Header Pin Definition

Pin Signal

1GPO0

Controls, LEDs, and Connectors

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)

3.5.4 Miscellaneous I/O

2GPI0

3GPO1

4GPI1

5GPO2

6GPI2

7GPO3

8GPI3

93.3V

10 GND

Table 3-32 P30, GPIO Header Pin Definition (continued)

Pin Signal

Table 3-33 P16, Miscellaneous I/O Header Pin Definition

Pin Signal Pin Signal

1 HD_LED 2 POWER_LED

3 HD_LED# 4 POWER_LED#

5 GND 6 EXT_PWRBTN_N

7 PM_SYSRST_N 8 GND

9NC 10Key

Controls, LEDs, and Connectors

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D) 47

3.5.5 SPI Flash

You must set the jumper defined below if you want to configure how the SPI flash is accessed.

Use Jumper P15 to enable or disable the BIOS on the COM Express module

Table 3-34 P13, SPI Flash Header Pin Definition

Pin Signal

13.3V DUAL

2GND

3SPI_CS_N

4SF_SPI_CLK

5SF_SPI_SO

6SF_SPI_SI

7NC

8NC

Table 3-35 P12 and P14, Jumper Settings for SPI Flash SF100 header

P12 Jumper Setting Configuration

P12 (1-2) To PCH (Default)

P12 (2-3) To SF100 header

P14 Jumper Setting Configuration

P14 (1-2) Enable SPI flash chip U9 and disable U10 (Default)

P14 (2-3) Enable SPI flash chip U10 and disable U9

Table 3-36 P15 and P38, Jumper Configuration to Enable/Disable BIOS

P15 Jumper Setting Configuration

P15 (1-2) Enable BIOS on the module (Default)

Controls, LEDs, and Connectors

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)

3.5.6 EEPROM

P15 (2-3) Disable BIOS on the module

P38 Jumper Setting Configuration

P38 (1-2) Enable CS1 of BIOS on the module (Default)

P38 (2-3) Disable CS1 of BIOS on the module

Table 3-37 P17 Case Open Select Header

P17 Setting Configuration

P17 (1-2) Disable the case open select header (Default)

P17 (2-3) Enable the case open select header

Table 3-36 P15 and P38, Jumper Configuration to Enable/Disable BIOS (continued)

P15 Jumper Setting Configuration

Table 3-38 P31, EEPROM Header Pin Definition

Pin Signal

1I2C_CLK

2I2C_DATA

3GND

Chapter 4

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D) 49

Functional Description

4.1 Block Diagram

4.2 Video

The COMX-CAR-610 supports dual-independent displays using the Mobile Intel processor

Integrated Graphics Controller. This carrier supports following graphic interfaces:

Figure 4-1 COM Express Type 6 Block Diagram

Functional Description

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)

4.2.1 LVDS

The graphic controller supports up to 24-bit colors per pixel so the COMX-CAR-610 could

support 24-bit LCD panels using different cables.

The board provides an LVDS and backlight header. The LVDS header is a 40 pin, dual-row

header, while the backlight is a 5 pin wafer header.

For information on pin assignments, Table 3-4 on page 33

4.2.2 VGA

The carrier board supports VGA output from the COM Express connector. The VGA signals

come from the same connector as the HDMI signals.

For information on pin assignments, Table 3-7 on page 34.

4.2.3 HDMI

The COMX-CAR-610 supports an HDMI interface from DDI1 of the COM Express connector.

For information on pin assignments, Table 3-8 on page 35.

4.2.4 Display Port

The COMX-CAR-610 supports two Display Ports from DDI2 and DDI3 of the COM Express

connector.

For information on pin assignments, see Table 3-9 on page 35.

4.3 Audio

The COMX-CAR-610 supports line output, microphone output, and line input using industry

standard 3.5 mm mini-jack connectors. The board also provides a two-channel HD audio as

part of the integrated High-Definition Multimedia Interface (HDMI). The integrated HDMI

requires a 1.5 V CODEC.

For information on pin assignments, see Table 3-10 on page 36 and Table 3-11 on page 37.

Functional Description

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D) 51

4.4 LAN

There are two Gigabit Ethernet ports: one is routed from the COM Express connector, and the

other from WG82574L. The RJ-45 connectors are located on the board and both support

100/1000 Base T.

The LAN connectors have two integrated LEDs. When the green LED is OFF, it indicates that

LAN link is not established. When it is ON, it indicates that a LAN link is established. When it

"blinks," it indicates LAN link activity. A second green LED shall BLINK indicating the activity

state of 100Mbps or 1000Mbps LAN.

For information on pin assignments, see Table 3-12 on page 37.

4.5 PCI Express

The board has one x1 PCI-E slot and and one x16 PCI-E slot. The x16 PCI-E slot can be used for

PCI Express Graphics (PEG). There are also two x4 PCI-E slots. One of the x4 slots can be used

for other applications by using PCI-E multiplexer devices.

For information on pin assignments, see Table 3-13 on page 38.

Figure 4-2 PCI Express Block Diagram

Functional Description

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)

4.5.1 PCI Express Mini Card

The carrier board comes with a PCI Express Mini Card connector that supports the Intel

WiMAX/WiFi Link 5050 and Intel WiFi Link 5000 series of wireless devices. The connector

conforms to PCI Express Mini Card Electromechanical Specification 1.1, implementing both

PCI Express and USB interfaces. The PCI-E Mini Card is available only when the related PCI-E

MUX and USB MUX are both set appropriately.

4.6 USB

The are four USB 2.0 ports on the board. Two of them could be used for other applications: one

for external USB flash, and the other for a PCI-E Mini Card through a USB MUX device. All USB

2.0 ports support low-speed, full-speed, and high-speed transfer rates using the USB 2.0

Enhanced Host Controller Interface (EHCI).

There are also four USB 3.0 ports from COM Express connector. The USB 3.0 ports support low-

speed, full-speed, and high-speed transfer rates using the USB 3.0 Enhanced Host Controller

Interface (EHCI).

For information on pin assignments, see Table 3-20 on page 40.

4.7 Storage

There are four SATA sockets on the carrier board for connecting to internal SATA 2.0 devices.

Figure 4-3 PCI Express Mini Card Setting

Functional Description

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D) 53

For information on pin assignments, see Table 3-21 on page 41.

4.8 Super I/O

The COMX-CAR-610 provides a Super I/O for extending several function modules.

For information on pin assignments, see Super I/O on page 41.

4.8.1 Voltage and Thermal Monitoring

The COMX-CAR-610 provides voltage monitoring capabilities on 3 V, 5 V, and 12 V rails, and

also provides thermal monitoring capabilities for the COM Express module and its

environment. Voltage and thermal values are read by the management engine, and alerts are

reported to the management engine.

Figure 4-4 Super I/O Block Diagram

Functional Description

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)

4.8.2 Fan Control

There are two 4-wire fan headers on the COMX-CAR-610 for module fan and system fan. Fans

support fan TACH input and PWM fan speed control. The board uses a 4-pin locking connector

equivalent to Molex 47053-1000.

For information on pin assignments, see Table 3-22 on page 41.

4.8.3 PS/2

There is a 6-pin wafer PS/2 header for keyboard and mouse.

For information on pin assignments, see Table 3-23 on page 42.

4.8.4 LPT

There is a 2 x 13 pin header for the LPT interface on the COMX-CAR-610.

For information on pin assignments, see Table 3-24 on page 42.

4.8.5 RS-232 and RS-422/485 Ports

The COMX-CAR-610 implements up to six RS-232 ports, two of which can be switched to RS-

422 or RS-485 ports by setting two jumpers on the 2 x 3 pin header. All the RS-232 ports are

implemented as 2 x 5 pin, dual-row headers, and the RS-422/485 ports as 1 x 4 pin, single-row

headers.

Two of the six COM ports from the Super I/O can be configured as RS-232 ports, or as RS-422

or RS-485 ports by setting a 6-pin, dual-row jumper.

For information on pin assignments, see Table 3-25 on page 43 and Table 3-26 on page 43.

Functional Description

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D) 55

4.9 SPI Flash

There are two SPI flash chips. Each chip has a capacity of 4 MB for BIOS, Gigabit Ethernet, and

ME.

The flash chips can be accessed either by the PCH or external devices with SPI interface through

a 2 x 4 pin SF100 header.

A 3-pin jumper (P12) is supplied to configure how SPI flash is accessed, and when the SPI flash

is set to be accessed by external devices through the SF100 header. Each of the SPI flash chips

can be enabled or disabled by setting a 3-pin jumper (P14). For information on pin

assignments, see Table 3-35 on page 47.

The COMX-CAR-610 also provides two 3-pin jumpers (P15 and P38) to determine whether

enable or disable the BIOS on the module. For information on pin assignments, see Table 3-36

on page 47.

Figure 4-5 SPI Flash Block Diagram

Functional Description

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)

4.10 Watchdog Timer

The COMX-CAR-610 provides a watchdog timer (WDT), which is a combination of two

watchdog timers coming from COM Express connector and Super I/O.

A valid WDT output signal resets the COMX-CAR-610. The BIOS disables the device at boot

(software is enabled when the watchdog application loads). The WDT is disabled before

entering S3 state, and re-enabled upon exiting S3.

4.11 Real Time Clock (RTC)

There is an onboard SMT battery holder. The battery holder allows for the quick and easy

replacement of a 3 V button cell lithium battery which provides backup power to the onboard

RTC.

The RTC supports two lockable memory ranges. By setting bits in the configuration space, two

8-byte ranges can be locked to read and write accesses. This prevents unauthorized reading of

passwords or other system security information.

Figure 4-6 Watchdog Timer Block Diagram

Functional Description

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D) 57

The RTC also supports a data alarm that allows for scheduling a wake up event up to 30 days in

advance rather than just 24 hours in advance.

4.12 Wake Events

The COMX-CAR-610 awakes from sleep states S3 and S4 when one of the following conditions

occur:

Table 4-1 Wake Events

Wake Events Description

PCI Express Through PE_WAKE_N

LAN The management engine supports Wake-on-LAN (WOL) using

wired LAN.

USB -

Power button If the power button is pressed for more than four seconds, it causes

an unconditional transition to the S5 state.

Functional Description

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)

Appendix A

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D) 59

ARelated Documentation

A.1 Emerson Network Power—Embedded Computing

Documents

The publications listed below are referenced in this manual. You can obtain electronic copies of

Emerson Network Power, Embedded Computing publications by contacting your local

Emerson sales office. For released products, you can also visit our Web site for the latest copies

of our product documentation.

1. Go to www.emersonnetworkpower.com/embeddedcomputing.

2. Under Resources, click Technical Documentation.

3. Enter the manual you are looking for in the search field. Use either the publication number

or the complete name of the product to search for available manuals.

A.2 Manufacturers’ Documents

You can also get additional information from manufacturers’ documentation. Note that the

information in these documents are subject to change without prior notice.

Table A-1 Emerson Network Power, Embedded Computing Publications

Document Title Publication Number

COMX-CAR-610 COM Express Carrier Board Quick Start Guide 6806800A13

COMX-CAR-610 COM Express Carrier Board Release Notes TBD

COMX-CAR-610 COM Express Carrier Board Safety Notes 6806800A12

COMX-CAR-610 Installation and Use 6806800K26

COMX-CAR-610 Quick Start Guide 6806800K27

COMX-CAR-610 Safety Notes 6806800K28

Related Documentation

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D) 61

Safety Notes

This section provides warnings that precede potentially dangerous procedures throughout

this manual. Instructions contained in the warnings must be followed during all phases of

operation, service, and repair of this equipment. You should also employ all other safety

precautions necessary for the operation of the equipment in your operating environment.

Failure to comply with these precautions or with specific warnings elsewhere in this manual

could result in personal injury or damage to the equipment.

Emerson intends to provide all necessary information to install and handle the product in this

manual. Because of the complexity of this product and its various uses, we do not guarantee

that the given information is complete. If you need additional information, ask your Emerson

representative.

The product has been designed to meet the standard industrial safety requirements. It must

only be used in its specific area of office telecommunication industry, industrial control, and

development. It must not be used in safety critical components, life supporting devices or on

aircraft.

Only personnel trained by Emerson or persons qualified in electronics or electrical engineering

are authorized to install, remove or maintain the product. The information given in this manual

is meant to complete the knowledge of a specialist and must not be used as replacement for

qualified personnel.

Keep away from live circuits inside the equipment. Operating personnel must not remove

equipment covers. Only factory authorized service personnel or other qualified service

personnel is allowed to remove equipment covers for internal subassembly or component

replacement or any internal adjustment.

Do not install substitute parts or perform any unauthorized modification of the equipment or

the warranty may be voided. Contact your local Emerson representative for service and repair

to make sure that all safety features are maintained.

Emerson and our suppliers take significant steps to make sure that there are no bent pins on

the backplane or connector damage to the boards prior to leaving the factory. Bent pins

caused by improper installation or by inserting boards with damaged connectors could void

the Emerson warranty for the backplane or boards.

This product operates with dangerous voltages that can cause injury or death. Use extreme

caution when handling, testing, and adjusting this equipment and its components.

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)

Safety Notes

EMC

FCC Class A

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to Part 15 of the FCC Rules, EN55022. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, can cause

harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which

case the user is required to correct the interference at his own expense.

Use only shielded cables when connecting peripherals to assure that appropriate radio

frequency emissions compliance is maintained. Installed blades must have the face plates

installed and all vacant slots in the shelf must be covered.

Safety Notes

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D) 63

For applications where this product is provided without a face plate, or where the face plate has

been removed, your system chassis/enclosure must provide the required electromagnetic

interference (EMI) shielding to maintain EMC compliance.

Board products are tested in a representative system to show compliance with the above

mentioned requirements. A proper installation in a compliant system maintains the required

performance.

As soon as you modify the product or change the default configuration you are responsible for

complying with all relevant regulatory standards.

VCCI

This is a Class A product based on the standard of the Voluntary Control Council for

Interference by Information Technology Interference (VCCI). If this equipment is used in a

domestic environment, radio disturbance can arise. When such trouble occurs, the user is

required to take corrective actions.

Installation

Damage of Circuits

Electrostatic discharge and incorrect installation and removal of the product can damage

circuits or shorten their life.

Before touching the product make sure that your are working in an ESD-safe environment or

wear an ESD wrist strap or ESD shoes. Hold the product by its edges and do not touch any

components or circuits.

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)

Safety Notes

Operation

Product Damage

High humidity and condensation on surfaces cause short circuits.

Do not operate the product outside the specified environmental limits. Make sure the product

is completely dry and there is no moisture on any surface before applying power.

Battery

Data Loss

Installing another battery type than the one that is mounted at product delivery may cause

data loss since other battery types may be specified for other environments or may have a

shorter lifetime.

Only use the same type of lithium battery as is already installed.

PCB and Battery Holder Damage

Removing the battery with a screw driver may damage the PCB or the battery holder.

Do not use a screw driver to remove the battery from its holder.

Product Damage

Incorrect replacement of lithium batteries can result in a hazardous explosion.

When exchanging the on-board lithium battery, make sure that the new and the old battery

are exactly the same battery models.

If the respective battery model is not available, contact your local Emerson sales

representative for the availability of alternative officially approved battery models.

Environment

Environmental Damage

Improperly disposing of used products may harm the environment.

Always dispose of used products according to your country’s legislation and manufacturer’s

instructions.

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D) 65

Sicherheitshinweise

Dieses Kapitel enthält Hinweise, die potentiell gefährlichen Prozeduren innerhalb dieses

Handbuchs vorrangestellt sind. Beachten Sie unbedingt in allen Phasen des Betriebs, der

Wartung und der Reparatur des Systems die Anweisungen, die diesen Hinweisen enthalten

sind. Sie sollten außerdem alle anderen Vorsichtsmaßnahmen treffen, die für den Betrieb des

Systems innerhalb Ihrer Betriebsumgebung notwendig sind. Wenn Sie diese

Vorsichtsmaßnahmen oder Sicherheitshinweise, die an anderer Stelle diese Handbuchs

enthalten sind, nicht beachten, kann das Verletzungen oder Schäden am System zur Folge

haben.

Emerson ist darauf bedacht, alle notwendigen Informationen zum Einbau und zum Umgang

mit dem System in diesem Handbuch bereit zu stellen. Da es sich jedoch bei dem System um

ein komplexes Produkt mit vielfältigen Einsatzmöglichkeiten handelt, können wir die

Vollständigkeit der im Handbuch enthaltenen Informationen nicht garantieren. Falls Sie

weitere Informationen benötigen sollten, wenden Sie sich bitte an die für Sie zuständige

Geschäftsstelle von Emerson.

Das Produkt erfüllt die für die Industrie geforderten Sicherheitsvorschriften und darf

ausschließlich für Anwendungen in der Telekommunikationsindustrie, im Zusammenhang mit

Industriesteuerungen und in der Entwicklung verwendet werden. Es darf nicht in

sicherheitskritischen Anwendungen, lebenserhaltenden Geräten oder in Flugzeugen

verwendet werden.

Einbau, Wartung und Betrieb dürfen nur von durch Emerson ausgebildetem oder im Bereich

Elektronik oder Elektrotechnik qualifiziertem Personal durchgeführt werden. Die in diesem

Handbuch enthaltenen Informationen dienen ausschließlich dazu, das Wissen von

Fachpersonal zu ergänzen, können dieses jedoch nicht ersetzen.

Halten Sie sich von stromführenden Leitungen innerhalb des Systems fern. Entfernen Sie auf

keinen Fall die Systemabdeckung. Nur werksseitig zugelassenes Wartungspersonal oder

anderweitig qualifiziertes Wartungspersonal darf die Systemabdeckung entfernen, um

Systemkomponenten zu ersetzen oder andere Anpassungen vorzunehmen.

Installieren Sie keine Ersatzteile oder führen Sie keine unerlaubten Veränderungen am System

durch, sonst verfällt die Garantie. Wenden Sie sich für Wartung oder Reparatur bitte an die für

Sie zuständige Geschäftsstelle von Emerson. So stellen Sie sicher, dass alle

sicherheitsrelevanten Aspekte beachtet werden.

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)

Sicherheitshinweise

Emerson und unsere Zulieferer unternehmen größte Anstrengungen um sicherzustellen, dass

sich Pins und Stecker von Boards vor dem Verlassen der Produktionsstätte in einwandfreiem

Zustand befinden. Verbogene Pins, verursacht durch fehlerhafte Installation oder durch

Installation von Boards mit beschädigten Steckern kann die durch Emerson gewährte Garantie

für Boards und Backplanes erlöschen lassen.

Dieses Produkt wird mit gefährlichen Spannungen betrieben, die zu Verletzungen und Tod

führen können. Seien Sie im Umgang mit dem Produkt und beim Testen und Anpassen des

Produktes und seiner Komponenten äußerst vorsichtig.

EMV

FCC Class A

Das Produkt wurde getestet und erfüllt die für digitale Geräte der Klasse A gültigen Grenzwerte

gemäß den FCC-Richtlinien Abschnitt 15 bzw. EN 55022 Klasse A. Diese Grenzwerte sollen

einen angemessenen Schutz vor Störstrahlung beim Betrieb des Produkts in Geschäfts-,

Gewerbe- sowie Industriebereichen gewährleisten. Das Produkt arbeitet im

Hochfrequenzbereich und erzeugt Störstrahlung. Bei unsachgemäßem Einbau und anderem

als in diesem Handbuch beschriebenen Betrieb können Störungen im Hochfrequenzbereich

auftreten.

Diese Einrichtung kann im Wohnbereich Funkstörungen verursachen; in diesem Fall kann vom

Betreiber verlangt werden, angemessene Maßnahmen durchzuführen und dafür

aufzukommen.

Benutzen Sie zum Anschließen von Peripheriegeräten ausschließlich abgeschirmte Kabel. So

stellen Sie sicher, dass ausreichend Schutz vor Störstrahlung vorhanden ist. Die Blades müssen

mit der Frontblende installiert und alle freien Steckplätze müssen mit Blindblenden abgedeckt

sein.

Änderungen, die nicht ausdrücklich von Emerson erlaubt sind, können Ihr Recht das System zu

betreiben zunichte machen.

Sicherheitshinweise

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D) 67

Wenn dieses Produkt ohne Frontblende ausgeliefert wird oder wenn die Frontblende entfernt

wird, muss Ihr System die notwendigenSchutzmechnismen gegen elektromagnetische

interferenzen bereitstellen, um die Einhaltung der eletromagnetischen Verträglichkeit des

Systems zu gewährleisten.

Boardprodukte werden in einem repräsentativen System getestet, um zu zeigen, dass das

Board den oben aufgeführten EMV-Richtlinien entspricht. Eine ordnungsgemäße Installation

in einem System, welches die EMV-Richtlinien erfüllt, stellt sicher, dass das Produkt gemäß den

EMV-Richtlinien betrieben wird.

Sobald Sie das Produkt oder seine Standardkonfiguration verändern, müssen Sie dafür sorgen,

dass alle relevanten Richtlinien eingehalten werden.

VCCI

Das Produkt ist eine Einrichtung der Klasse A gemäß dem Standard des Voluntary Control

Council for Interference von Information Technology Interference (VCCI). Wird das Produkt in

Wohngegenden betrieben, können Störungen im Hochfrequenzbereich auftreten. In einem

solchen Fall ist der Benutzer verpflichtet, entsprechende Gegenmaßnahmen zu ergreifen.

System Installation

Beschädigung von Schaltkreisen

Elektrostatische Entladung und unsachgemäßer Ein- und Ausbau des Produktes kann

Schaltkreise beschädigen oder ihre Lebensdauer verkürzen.

Bevor Sie das Produkt oder elektronische Komponenten berühren, vergewissern Sie sich, daß

Sie in einem ESD-geschützten Bereich arbeiten.

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)

Sicherheitshinweise

Betrieb

Beschädigung des Systems

Hohe Luftfeuchtigkeit und Kondensat auf den Oberflächen der Produkte kann zu

Kurzschlüssen führen.

Betreiben Sie die Produkte nur innerhalb der angegebenen Grenzwerte für die relative

Luftfeuchtigkeit und Temperatur und stellen Sie vor dem Einschalten des Stroms sicher, dass

sich auf den Produkten kein Kondensat befindet.

Batterie

Datenverlust

Wenn Sie einen anderen Batterietyp installieren als der, der bei Auslieferung des Produktes

installiert war, kann Datenverlust die Folge sein, da die neu installierte Batterie für andere

Umgebungsbedingungen oder eine andere Lebenszeit ausgelegt sein könnte.

Verwenden Sie daher den gleichen Batterietyp, der bei Auslieferung des Produktes installiert

war.

Beschädigung des PCBs und der Batteriehalterung

Wenn Sie die Batterie mit einem Schraubendreher ausbauen, können das PCB und die

Batteriehalterung beschädigt werden.

Benutzen Sie keinesfalls einen Schraubendreher, um die Batterie aus der Halterung zu nehmen.

Beschädigung des Produktes

Fehlerhafter Austausch von Lithium-Batterien kann zu gefährlichen Explosionen führen.

Wenn SIe die Lithium-Batterie auf dem Produkt austauschen, stellen Sie sicher, dass die alte

und die neue Batterie vom gleichen Typ sind.

Ist der Batterietyp nicht verfügbar, wenden Sie sich an Emerson um herauszufinden, welcher

Batterietyp offiziell alternativ verwendet werden darf.

Sicherheitshinweise

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D) 69

Umweltschutz

Umweltverschmutzung

Falsche Entsorgung der Produkte schadet der Umwelt.

Entsorgen Sie alte Produkte gemäß der in Ihrem Land gültigen Gesetzgebung und den

Empfehlungen des Herstellers.

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)

Sicherheitshinweise

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D) 71

abbreviations 11

block diagram

carrier board type 6 49

box contents 23

conventions 13

environmental requirements 21

Installation

Module 24

installing

COM Express module 24

installing COM Express module 24

power requirements 22

removing

COM Express module 24

onboard battery 26

removing COM Express module 24

removing onboard battery 26

requirements

environmental 21

power 22

shipment contents 23

Index

COMX-CAR-610 COM Express Carrier Board Installation and Use (6806800K26D)

HOW TO REACH LITERATURE AND TECHNICAL SUPPORT:

For literature, training, and technical assistance and support programs, visit

www.emersonnetworkpower.com/embeddedcomputing

Emerson, Business-Critical Continuity, Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co.

All other product or service names are the property of their respective owners.

Emerson Network Power.

The global leader in enabling Business-Critical Continuity™

AC Power Systems

Connectivity

DC Power Systems

Embedded Computing

Embedded Power

Integrated Cabinet Solutions

Outside Plant

Power Switching & Control

Precision Cooling

Services

Site Monitoring

Surge & Signal Protection