121737-0370, Rev. B
9-10-99
DTC-01
OC-1 Single Mode Transceiver
with Clock Recovery
Features
þ
Full Compliance with OC-1 SONET
Specifications
þ
Long Reach 1310 nm & 1550 nm and
Intermediate Reach
þ
Eye Safe (Class I Laser Safety)
þ
Multi-sourced 2x9 package style
þ
Duplex SC or ST or FC connector
þ
- 40°C to +85°C Operating Temperature
(option “A”)
þ
Single +5 V supply & DATA & CLOCK
PECL interface
þ
Wave Solder Process Compatible
The DTC-01 fiber optic transceivers with clock recovery offer a
simple, convenient way to interface A TM/SONET/SDH OC-1 PCBs
to single mode fiber optic cables. Both Long Reach (1300 nm or
1550 nm) and Intermediate Reach versions are available using either
DFB Lasers or Fabry Perot Lasers where appropriate. All modules
satisfy Class I Laser Safety requirements in accordance with the US
FDA/CDRH and international IEC-825 standards.
The transmit and receive functions are contained in a two-row, 18-pin
(2x9) package with a Duplex SC or ST or FC connector interface.
The transmitter includes the laser driving circuitry as well as an Average
Power Control (APC) loop to stabilize the transmitter average optical
output power . A Transmitter Disable input, a Laser Back Facet
Monitor and differential Laser Bias Monitor outputs and a Transmitter
Alarm output are provided. The receiver features a high performance
InGaAs PIN photodiode and a transimpedance amplifier IC with
internal AGC for wide dynamic range. A PLL clock recovery IC is
used to generate PECL data and clock. A Signal Detect status TTL
output is also included.
The transceiver operates from a single +5V supply over an operating
temperature range of 0°C to +70°C (“B” option) or - 40°C to +85°C
(“A” option). The package is made of either conductive plastic with
blue color (Duplex-SC version) or metal (FC and ST version) for
excellent EMI shielding.
Related OC-1 tranceivers
DTR-052-SM: 1x9 Transceiver without Clock Recovery, 5 V supply
DTR-052-SM2: 2x9 Transceiver without Clock Recovery , 5 V supply
DTR-052-3.3-SM: 1x9 Transceiver without Clock Recovery, 3.3 V
DTR-052-3.3-SM2: 2x9 Transceiver without Clock Recovery, 3.3 V
Description
Optical Communication Products, Inc.
Absolute Maximum Ratings
Parameter Symbol Minimum Maximum Units
Storage Te mperat ure Tst - 40 + 85 °C
O per at ing Temp er at ur e "A" opt ion Top - 40 + 85 °C
"B" opt ion 0 + 70
Sup ply Vo lt a ge VCC 0+ 6.0V
Input Voltage Vin 0VCC V
Outp ut Curre nt IO-50mA
Lead Solder ing Te mper atur e & Time -- 260°C, 10 s ec
2
21737-0370, Rev. B
9-10-99
Transmitter Performance Characteristics (over Operating Case Temperature Range)
DTC-01
Parameter Symbol Minimum Typical Maximum Units
Data Rate B51 51.84 52 Mb/s
Average Opt ic al
Output Power
( c oupled into s ingle
mode f iber),
50% duty cycle
L0
Po
- 5. 0 - 3. 0 0
dBm
L1 - 8. 0 - 5. 0 - 2. 0
L2 - 12. 0 - 8. 0 - 5. 0
L3 - 15. 0 - 11. 0 - 8. 0
Extinction Ratio Phi / Plo 10 - - dB
C ente r Wa v el ength I R (Int ermediate Reach)
lc
1261 1310 1360 nmLR1 (Long Reach 1310 nm) 1280 1310 1335
LR2 (Long Reach 1550 nm) 1480 1550 1580
Spectr al Width (RM S) LR1 (0°C to 70°C) & IR DlRMS --4
nm
Spectr al Width (-20 dB) LR1 (- 4 0° C t o 85° C) & LR2 Dl20 --1
O ptical Rise and Fall Time ( 10% t o 90% ) tr, tf-24ns
O ptical Out put Eye compliant wit h Bellcore TR-NW T- 000253
Receiver Performance Characteristics (over Operating Case Temperature Range)
T ransmitter Electrical Interface (over Operating Case Temperature Range)
Parameter Symbol Minimum Typical Maximum Units
Data Rate B51 51.84 52 Mb/s
Op ti c al Input P o we r ( 1 0 -10 BER) 1 Pin - 36.0 - 40.0 - 7.0 dBm
Si gnal D etect Thresholds Increasing Light Input Psd+ - - - 36.0 dBm
D ecreasing Li ght Input Psd- - 45.0 - - dBm
Si gnal D etect Hysteresis - 0.5 - dB
Wavelength of Operation l1100 - 1600 nm
Output C lock J itter CLKJ--0.1UIrms
Jitter B andwidth BWJ-4052kHz
Maxi mum Jitter Amplification AJ--0.1dB
1
The receiver optical input power (sensitivity) is specified and measured at 1300 nm wavelength with 223-1 P RBS .
Parameter Symbol Minimum Typical Maximum Units
Input HIGH Voltage VIH VCC - 1.165 -VCC - 0.700 V
Input LOW Voltage VIL VCC - 1.890 -VCC - 1.475 V
Data Inp ut C urrent - HIGH IH- - 350 mA
Data Inp ut C urrent - LOW IL- - 250 mA
Transmitter Di sable Voltage VDIS VCC - 2 .0 -VCC V
Transmitter Enable Voltage VEN 0-0.8V
Transmitter
End-of-Li fe Alarm Normal Operation VNO 0-0.8V
End-of-Life VEOL VCC - 0 .5 -VCC V
Differenti al Bi as Monitor Voltage (Ta = 25°C ) VBM+ - V BM- 0.02 - 0.12 V
Bac k Fa c e t M o ni to r Volta g e (Ta = 25°C ) 1VFM 0.4 - 2.8 V
1 F o r manufa c tur ing p ur p o s e s
321737-0370, Rev. B
9-10-99
Transmitter: When the DA T A+ input is at logic HIGH and DAT A-
input is at logic LOW , the LD is ON; and vice versa. In single-ended
applications, the unused input pin should be biased to VCC - 1.29 V.
The transmitter is normally enabled (i.e. when the TX DISABLE input
is not connected). When the TX DISABLE input voltage is higher than
VCC - 2 V, the laser is turned off independent of the input data. A
Transmitter End-of-Life Alarm (TALM) is also provided, which will switch
to TTL level HIGH when the laser is reaching its End-of-Life.
The transmitter incorporates an A verage Power Control (APC) loop
to stabilize the transmitter average optical output power against
temperature variation. The APC loop always acts to keep the
transmitter average optical output power at a constant value (assuming
that the transmitter is enabled). Therefore, when the input data is all
continuous “zeroes” or all continuous “ones”, the transmitter optical
output power is a constant level equal to the nominal average optical
output power (not at the “OFF” level or at the “ON” level).
Receiver: Both differential outputs (DAT A+ and DA T A-, CLOCK+
and CLOCK-) are PECL levels requiring termination (50 ohms to
VCC - 2 volts or 510 ohms to GND is recommended). For optimum
performance, both outputs should be terminated in the same manner,
even if only one is used.
The Signal Detect circuit monitors the level of the incoming optical
signal and generates a TTL logic LOW signal when insufficient
DTC-01
Control
Circuit
Bias
Circuit
200 W
10 W
PD
I
mon
I
b
LD
3 KW
3 KW
FM
BM +
V
CC
V
CC
GND
GND
BM -
3 KW
photocurrent is produced.
Interface circuit: The power supply line should be well-filtered.
All 0.1 mF power supply bypass capacitors should be as close to
the DTC transceiver module as possible. The two front GND posts
should be grounded to Circuit Ground or Chassis Ground.
Laser Safety: All transmitters are Class I Laser products per FDA/
CDRH and IEC-825 standards. They must be operated under
specified operating conditions.
FC Receptacle Package
LD Bias
Monitor Circuit
DA TA & CLOCK Timing
LD Back Facet
Monitor Circuit
Dimension in inches [mm]
Optical Communication Products, Inc.
DA TE OF MANUFACTURE:
MANUFACTURED IN THE USA
This product complies with
21 CFR 1040.10 and 1040.1 1
Meets Class I Laser Safety Requirements
Receiver Electrical Interface (over Operating Case Temperature Range)
Electrical Power Supply Characteristics (over Operating Case Temperature Range)
Application Notes
Parameter Symbol Minimum Typical Maximum Units
Output HIGH Voltage (DATA & C LOCK) VOH VCC - 1.200 -VCC - 0.700 V
Output LOW Voltage (DATA & C LOCK) VOL VCC - 2.000 -VCC - 1.620 V
O utput Cur r ent IO--25mA
SIGNAL DETE CT Output HIGH Vo ltag e VOH 2.7 - VCC V
SIGNAL DE TE C T Output LOW Voltage VOL 0 - 0.50 V
Parameter Symbol Minimum Typical Maximum Units
Supply Volt age VCC 4.75 5.0 5.25 V
Supply Current TX ICC - 100 130 mA
RX ICC - 200 270 mA
DATA
CLOCK
Set-up
7.5 < tS < 12 ns Hold
7.5 < tH < 12 ns
4
21737-0370, Rev. B
9-10-99
Optical Communication Products, Inc. reserves the right to make changes in equipment design or specifications without notice. Information supplied by Optical Communication
Products, Inc. is believed to be accurate and reliable. However, no responsibility is assumed by Optical Communication Products, Inc. for its use nor for any infringements of third
parties which may result from its use. No license is granted by implication or otherwise under any patent right of Optical Communication Products, Inc.
Optical Communication Products, Inc.
9736 Eton A venue, Chatsworth, CA 91311, T el.: 818-701-0164, F AX: 818-701-1468
DTC-01
PIN FUNCTION PIN FUNCTION
1 N/C 10 TX GND
2 N/C 11 TD+ (TX DATA IN +)
3 CLOCK - 12 TD- (TX DATA IN -)
4CLOCK + 13V
CCTX
5 BM- (BIAS MONITOR -) 14 VCCRX
6BM+ ( BI AS M O NITO R +) 15 SD (RX SIGNAL DETECT)
7 TX DI SABLE 16 RD- (RX DATA OUT -)
8T
ALM (TX ALARM) 1 7 RD+ (RX DATA OUT +)
9 FACET MO NITO R 18 RX GND
Duplex SC Receptacle Package
ST Receptacle Package
Ordering Information
DTC - 01 -
XX -T- Ln - DR
Receptacle
Blank : SC Receptacle
ST : ST Receptacle
FC : FC Receptacle
Distance Option
specifies the range for Center W avelength &
Spectral W idth to be compliant with SONET
standard
Blank: Intermediate Reach
LR1 : Long Reach 1310 nm
LR2 : Long Reach 1550 nm
Light Output Option
L0: - 3 dBm (typ.)
L1: - 5 dBm (typ.)
L2: - 8 dBm (typ.)
L3: - 11 dBm (typ.)
T emperature Range
A: - 40°C to 85°C
B: 0°C to 70°C
NOTES
1. For full compliance with OC-1 Intermediate Reach standard, the DTC-01-xx-T-L3 modules are recommended.
2. For full compliance with OC-1 Long Reach 1310 nm standard, the DTC-01-xx-A-L0-LR1 and DTC-01-xx-B-L0-LR1 modules
are recommended. The DTC-01-xx-A-L0-LR1 uses a DFB laser to satisfy the - 40°C to +85°C requirement for Center Wavelength.
3. For full compliance with OC-3/STM-1 Long Reach / L-1.2 standard, the DTC-01-xx-A-L0-LR2 and DTC-01-xx-B-L0-LR2
modules are recommended. Both modules use DFB lasers. However , the DTC-01- xx-A-L0-LR2 is specified only over - 25°C to +70°C.
4. The LR1 (- 40°C to +85°C) & LR2 options are available only with DFB lasers and L0 optical output power level.
Dimension in inches [mm]
Dimension in inches [mm]
18
10
91
521737-0370, Rev. B
9-10-99
Contents
Description ................................................................................................................................... 1
Absolute Maximum Ratings ....................................................................................................... 1
Features ........................................................................................................................................ 1
Transmitter Performance Characteristics................................................................................ 2
Receiver Performance Characteristics ..................................................................................... 2
Transmitter Electrical Interface ................................................................................................2
Receiver Electrical Interface...................................................................................................... 3
Electrical Power Supply Characteristics .................................................................................. 3
Application Notes ........................................................................................................................ 3
FC Receptacle Package ............................................................................................................................ 3
DAT A & CLOCK Timing ......................................................................................................................... 3
ST Receptacle Package ............................................................................................................................ 4
Duplex SC Receptacle Package ............................................................................................................... 4
Ordering Information ................................................................................................................. 4
