175 Watts LPQ170 Series Total Power: 110-175 Watts Input Voltage: 85-264 VAC 120-300 VDC # of Outputs: Quad Electrical Specs Input Input range Frequency Inrush current Efficiency EMI filter Power factor Safety ground leakage current Special Features * Active power factor correction * IEC EN61000-3-2 compliance * Adjustable outputs on 1, 3 & 4 Remote sense on main output * Single wire current sharing * Power fail and remote inhibit * Built-in EMI filter * Low output ripple * Overvoltage protection * Overload protection * Thermal overload protection * DC power good * 5 V standby output * Adjustable floating 4th output * Optional cover (-C suffix) Environmental Derate each output at 2.5% per degree from Maximum power Adjustment range Hold-up time Overload protection Overvoltage protection Standby output AC power failure Remote inhibit Remote sense DC-OK Electromagnetic susceptibility: designed to meet EN61000-4, -2, -3, -4, -5, -6, -8, -11, Level 3 Vibration: Three orthogonal axes, sweep at 1 oct/min, 5 min. dwell at four major resonances 0.75 G peak 5 Hz to 500 Hz, operational Storage temperature: -40 to 85C 110 W convection (75 W with cover LPQ172) 85 W convection - LPQ173 175 W with 30 CFM forced air (130 W with cover - LPQ172 only) 3.3 - 5.5V on main; -12 - 15V on 3rd output 3.3 - 25 V on 4th output- LPQ172 3.3 - 5.5V on 4th output on LPQ173 20 ms @175 W load at nominal line Short circuit protection on all outputs. Case overload protected @ 110-145% above peak rating Tracks outputs 1, 3 & 4; 15 to 35% 5 V @ 200 mA regulated 5% Logic Control 50 to 70C (except for -C version) Humidity: Operating; non-condensing 5% to 95% 1.0 mA @ 50/60 Hz, 264 VAC input Output Operating temperature: 0 to 50C ambient Low temperature start -20C 85-264 VAC, 120-300 VDC 47-63 Hz 38 A max, cold start @ 25C 75% typical at full load Meets FCC Class B conducted CISPR 22 Class B conducted EN55022 Class B conducted VDE 0878 PT3 Class B conducted 0.99 typical TTL logic signal goes high 100 - 500 msec after V1 output; It goes low at least 4 msec before loss of regulation Requires contact closure to inhibit outputs Compensates for 0.5 V lead drop min. Will operate without remote sense connected. Reverse connection protected. TTL logic signal goes high after main output is in regulation. It goes low when there is a loss of regulation Safety VDE UL CB CSA CE NEMKO 0805/EN60950/IEC60950 60950 Certificate and report CSA 60950 Level 3 Mark (LVD) EN 60950/EMKO-TSE Temperature coefficient: .04% per C 121 MTBF demonstrated: >550,000 hours at full load and 25C ambient conditions Technical Support: (888) 41-ASTEC or (407) 241-2752 Americas: (760) 930-4600 Europe (UK) 44 (1384) 842-211 Asia (HK) 852-2437-9662 rev 09.20.04 AMERICAS EUROPE ASIA 5810 Van Allen Way Carlsbad, CA 92008 Telephone: 760-930-4600 Facsimile: 760-930-0698 Astec House, Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX, UK Telephone: 44 (1384) 842-211 Facsimile: 44 (1384) 843-355 Units 2111-2116, Level 21 Tower1, Metroplaza 223, Hing Fong Road Fwai Fong, New Territories Hong Kong Telephone: 852-2437-9662 Facsimile: 852-2402-4426 Model Number Output Voltage Minimum Load Maximum Load with Convection Cooling Maximum Load with 30 CFM Forced Air Peak Load Regulation2 Ripple P/P(PARD)3 LPQ172 5 V (3.3 - 5.5 V) 12 V -12 V (-12 -15 V) 3.3-25 V 0A 0A 0A 0.5 A* 15 A 6A 1.5 A 2A 30 A 8A 3A 5A 32 A 10 A 3.5 A 5.5 A 2% 3% 3% 3% 50 mV 120 mV <1% <50mV or 1% LPQ173 5 V (3.3 - 5.5 V) 12 V -12 V (-12 -15 V) 5 V (3.3 - 5.5 V) 0A 0A 0A 0A 10 A 6A .2 A 10A 24 A 8A 3A 24 A 26 A 10 A 3.5 A 26 A 2% 3% 3% 2% 50 mV 120 mV <1% 50mV LPQ170 Series Ordering Information 1. Peak current lasting <30 seconds with a maximum 10% duty cycle. 2. At 25C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. 3. Peak-to-peak with 20 MHz bandwidth and 10 F in parallel with a 0.1 F capacitor at rated line voltage and load ranges. 4. 4th output adjustable 3.3-25 V factory set at 5 V. 5. *Minimum loads are required when output set below 5 Volts 6. Remote inhibit resets OVP latch 7. LPQ173-C has no convection rating. Note: -C suffix added to the model number indicates cover option and is limited to 50C operation. Pin Assignments Connector LPQ172 LPQ173 SK1 PIN 1 PIN 2 PIN 3 PIN 4 PIN 5 PIN 6 PIN 7 PIN 8 PIN 9 PIN 10 N/C 5V Standby N/C V1 SWP Common +V1 sense Sense common Remote inhibit DC power good POK V4 SWP 5V Standby +V4 Sense V1 SWP Common +V1 sense Sense common Remote inhibit DC power good POK SK2 PIN 1,2 PIN 3,4,5 PIN 6 PIN 7 PIN 8 PIN 9 +12 V Common -12 V POK +3.3 V to +25 V (Float) Common (Float) +12V Common -12V POK N/C N/C SK3 TB-1, 3 TB-2 TB-4 COMMON +5 V (3.3V to 5.5V) N/C COMMON +5V (3.3V to 5.5V) +5 (3.3V to 5.5V) SK4 PIN 1 PIN 3 PIN 5 GROUND LINE NEUTRAL GROUND LINE NEUTRAL Mating Connectors (SK4) AC Input: Molex 09-50-8051 (USA) Molex 09-91-0500 (UK) PINS: 08-58-0111 (SK3) Main output: Molex BB-124-08 (SK2) Aux DC Output/Power fail: Molex 09-50-8091 (USA) Molex 09-91-0900 (UK) PINS: 08-58-0111 (SK1) Control Signals: Molex 90142-0010 (USA) PINS: 90119-2110 or Amp: 87977-3 PINS: 87309-8 Astec connector kit #70-841-015, includes all of the above. www.astecpower.com 122 AMERICAS EUROPE ASIA 5810 Van Allen Way Carlsbad, CA 92008 Telephone: 760-930-4600 Facsimile: 760-930-0698 Astec House, Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX, UK Telephone: 44 (1384) 842-211 Facsimile: 44 (1384) 843-355 Units 2111-2116, Level 21 Tower1, Metroplaza 223, Hing Fong Road Fwai Fong, New Territories Hong Kong Telephone: 852-2437-9662 Facsimile: 852-2402-4426 LPQ170 Series Mechanical Drawing SK2 SK1 SK3 Notes: 1. Specifications subject to change without notice. 2. All dimensions in inches (mm), tolerance is 0.02". 3. Specifications are for convection rating at factory settings unless otherwise stated. 4. Mounting screw maximum insertion depth is 0.12". 5. Warranty: 1 year 6. Weight: 2 lb / 0.91 kg www.astec.com 123