LM4929 www.ti.com SNAS293B - DECEMBER 2004 - REVISED APRIL 2013 LM4929 BoomerTM Audio Power Amplifier Series Stereo 40mW Low Noise Headphone Amplifier with OCL Output Check for Samples: LM4929 FEATURES DESCRIPTION * * * * * * The LM4929 is an stereo audio power amplifier capable of delivering 40mW per channel of continuous average power into a 16 load or 25mW per channel into a 32 load at 1% THD+N from a 3V power supply. 1 23 OCL outputs -- No DC Blocking Capacitors External Gain-Setting Capability Available in Space-Saving VSSOP Package Ultra Low Current Shutdown Mode 2V - 5.5V Operation Ultra Low Noise APPLICATIONS * * * Portable CD players PDAs Portable Electronics Devices KEY SPECIFICATIONS * * * * * PSRR at 217Hz and 1kHz Output Power at 1kHz with VDD = 2.4V, 1% THD+N into a 16 load, 65dB (Typ) Output Power at 1kHz with VDD = 3V, 1% THD+N into a 16 load, 25 mW (Typ) Shutdown current, 40 mW (Typ), 2.0A (Max) Output Voltage change on release from Shutdown VDD = 2.4V, RL = 16, 1mV (Max) Boomer audio power amplifiers were designed specifically to provide high quality output power with a minimal amount of external components. Since the LM4929 does not require bootstrap capacitors or snubber networks, it is optimally suited for low-power portable systems. The LM4929 is configured for OCL (Output Capacitor-Less) outputs, operating with no DC blocking capacitors on the outputs. The LM4929 features a low-power consumption shutdown mode with a faster turn on time. Additionally, the LM4929 features an internal thermal shutdown protection mechanism. The LM4929 is unity gain stable and may be configured with external gain-setting resistors. 1 2 3 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Boomer is a trademark of Texas Instruments. All other trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2004-2013, Texas Instruments Incorporated LM4929 SNAS293B - DECEMBER 2004 - REVISED APRIL 2013 www.ti.com Block Diagram IN A OUT A + Bias Generator CBYPASS IN B OUT C + OUT B SD Click-Pop and SD Control Logic + Figure 1. Block Diagram Typical Application Figure 2. Typical OCL Output Configuration Circuit 2 Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4929 LM4929 www.ti.com SNAS293B - DECEMBER 2004 - REVISED APRIL 2013 Connection Diagram IN A 1 10 VDD 2 9 3 8 VoA SD NC BYP VoC 4 7 5 6 IN B VoB GND Figure 3. VSSOP Package Top View See NS Package Number DGS These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Absolute Maximum Ratings (1) (2) (3) Supply Voltage 6.0V -65C to +150C Storage Temperature Input Voltage (4) -0.3V to VDD + 0.3V Power Dissipation (5) Internally Limited ESD Susceptibility (6) 2000V ESD Susceptibility (7) 200V Junction Temperature Thermal Resistance (1) (2) (3) (4) (5) (6) (7) 150C JC (VSSOP) 56C/W JA (VSSOP) 190C/W Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication of device performance. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and specifications. Datasheet min/max specification limits are ensured by design, test, or statistical analysis. 10 Terminated input. The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, JA, and the ambient temperature, TA. The maximum allowable power dissipation is PDMAX = (TJMAX - TA)/ JA or the number given in Absolute Maximum Ratings, whichever is lower. For the LM4929, see power derating currents for more information. Human body model, 100pF discharged through a 1.5k resistor. Machine Model, 220pF-240pF discharged through all pins. Operating Ratings Temperature Range TMIN TA TMAX -40C T A 85C 2V VDD 5.5V Supply Voltage Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4929 3 LM4929 SNAS293B - DECEMBER 2004 - REVISED APRIL 2013 www.ti.com Electrical Characteristics VDD = 5V (1) (2) The following specifications apply for VDD = 5V, RL = 16, and CB = 4.7F unless otherwise specified. Limits apply to TA = 25C. Pin 3 connected to GND (3). Symbol Parameter Conditions LM4929 Typ (4) Limit (5) Units (Limits) IDD Quiescent Power Supply Current VIN = 0V, IO = 0A ISD Shutdown Current VSHUTDOWN = GND 2 5 mA (max) 0.1 2.0 VSDIH Shutdown Voltage Input High 1.8 A(max) V VSDIL Shutdown Voltage Input Low 0.4 V PO Output Power RL= 16 80 mW RL = 32 80 THD = 1%; f = 1 kHZ VNO Output Noise Voltage BW = 20Hz to 20kHz, A-weighted 10 V PSRR Power Supply Rejection Ratio VRIPPLE = 200mV sine p-p 65 dB (1) (2) (3) (4) (5) All voltages are measured with respect to the GND pin unless otherwise specified. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication of device performance. Pin 3 (NC) should be connected to GND for proper part operation. Typicals are measured at 25C and represent the parametric norm. Limits are specified to Texas Instruments' AOQL (Average Outgoing Quality Level). Electrical Characteristics VDD = 3.0V (1) (2) The following specifications apply for VDD = 3.0V, RL = 16, and CB = 4.7F unless otherwise specified. Limits apply to TA = 25C. Pin 3 connected to GND (3). Symbol Parameter Conditions LM4929 Typ (4) Limit (5) Units (Limits) IDD Quiescent Power Supply Current VIN = 0V, IO = 0A 1.5 3.5 mA (max) ISD Shutdown Current VSHUTDOWN = GND 0.1 2.0 A(max) PO Output Power THD = 1%; f = 1kHz R = 16 40 R = 32 25 mW VNO Output Noise Voltage BW = 20 Hz to 20kHz, A-weighted 10 V PSRR Power Supply Rejection Ratio VRIPPLE = 200mV sine p-p 65 dB (1) (2) (3) (4) (5) 4 All voltages are measured with respect to the GND pin unless otherwise specified. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication of device performance. Pin 3 (NC) should be connected to GND for proper part operation. Typicals are measured at 25C and represent the parametric norm. Limits are specified to Texas Instruments' AOQL (Average Outgoing Quality Level). Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4929 LM4929 www.ti.com SNAS293B - DECEMBER 2004 - REVISED APRIL 2013 Electrical Characteristics VDD = 2.4V (1) (2) The following specifications apply for VDD = 2.4V, RL = 16, and CB = 4.7F unless otherwise specified. Limits apply to TA = 25C. Pin 3 connected to GND (3). Symbol Parameter Conditions LM4929 Typ (4) Limit (5) Units (Limits) IDD Quiescent Power Supply Current VIN = 0V, IO = 0A 1.5 3 mA (max) ISD Shutdown Current VSHUTDOWN = GND 0.1 2.0 A(max) THD = 1%; f = 1kHz PO Output Power VNO Output Noise Voltage BW = 20 Hz to 20kHz, A-weighted 10 V PSRR Power Supply Rejection Ratio VRIPPLE = 200mV sine p-p 65 dB TWU Wake Up Time from Shutdown OCL 0.5 s (1) (2) (3) (4) (5) R = 16 25 R = 32 12 mW All voltages are measured with respect to the GND pin unless otherwise specified. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional but do not ensure specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which ensure specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not ensured for parameters where no limit is given, however, the typical value is a good indication of device performance. Pin 3 (NC) should be connected to GND for proper part operation. Typicals are measured at 25C and represent the parametric norm. Limits are specified to Texas Instruments' AOQL (Average Outgoing Quality Level). External Components Description See Figure 2 Components Functional Description 1. RI Inverting input resistance which sets the closed-loop gain in conjunction with Rf. This resistor also forms a high-pass filter with Ci at fc = 1/(2RiCi). 2. CI Input coupling capacitor which blocks the DC voltage at the amplifier's input terminals. Also creates a high-pass filter with Ri at fc = 1/(2RiCi). Refer to the section PROPER SELECTION OF EXTERNAL COMPONENTS for an explanation of how to determine the value of Ci. 3. Rf Feedback resistance which sets the closed-loop gain in conjunction with Ri. 4. CS Supply bypass capacitor which provides power supply filtering. Refer to the POWER SUPPLY BYPASSING section for information concerning proper placement and selection of the supply bypass capacitor. 5. CB Bypass pin capacitor which provides half-supply filtering. Refer to the section, PROPER SELECTION OF EXTERNAL COMPONENTS, for information concerning proper placement and selection of CB Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4929 5 LM4929 SNAS293B - DECEMBER 2004 - REVISED APRIL 2013 www.ti.com Typical Performance Characteristics 6 THD+N vs Frequency THD+N vs Frequency Figure 4. Figure 5. THD+N vs Frequency THD+N vs Frequency Figure 6. Figure 7. THD+N vs Frequency THD+N vs Frequency Figure 8. Figure 9. Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4929 LM4929 www.ti.com SNAS293B - DECEMBER 2004 - REVISED APRIL 2013 Typical Performance Characteristics (continued) THD+N vs Output Power THD+N vs Output Power Figure 10. Figure 11. Output Power vs Load Resistance Output Power vs Supply Voltage Figure 12. Figure 13. Output Power vs Supply Voltage Output Power vs Load Resistance Figure 14. Figure 15. Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4929 7 LM4929 SNAS293B - DECEMBER 2004 - REVISED APRIL 2013 www.ti.com Typical Performance Characteristics (continued) 8 Power Supply Rejection Ratio Power Supply Rejection Ratio Figure 16. Figure 17. Frequency Response vs Input Capacitor Size Open Loop Frequency Response Figure 18. Figure 19. Supply Voltage vs Supply Current Clipping Voltage vs Supply Voltage Figure 20. Figure 21. Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4929 LM4929 www.ti.com SNAS293B - DECEMBER 2004 - REVISED APRIL 2013 Typical Performance Characteristics (continued) Shutdown Hysteresis Voltage, VDD = 5V Shutdown Hysteresis Voltage, VDD = 3V Figure 22. Figure 23. Power Dissipation vs Output Power VDD = 5V Power Dissipation vs Output Power VDD = 3V 500 200 400 POWER DISSIPATION (mW) POWER DISSIPATION (mW) 450 RL = 16: 350 300 250 200 RL = 32: 150 100 160 RL = 16: 120 80 RL = 32: 40 50 0 0 0 50 150 100 200 0 OUTPUT POWER (mW) Figure 24. 20 30 40 50 60 70 80 90 OUTPUT POWER (mW) Figure 25. Power Dissipation vs Output Power VDD = 2.4V 10 THD+N vs Output Power VDD = 3V, RL = 32 120 RL = 16: 1 100 THD+N (%) POWER DISSIPATION (mW) 140 10 80 60 RL = 32: 40 0.1 20 Hz 20 kHz 0.01 1 kHz 20 0 0 10 20 30 40 50 60 0.001 1m OUTPUT POWER (mW) Figure 26. 10m 20m 100m OUTPUT POWER (W) Figure 27. Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4929 9 LM4929 SNAS293B - DECEMBER 2004 - REVISED APRIL 2013 www.ti.com Typical Performance Characteristics (continued) 10 THD+N vs Output Power VDD = 2.4V, RL = 32 THD+N vs Output Power VDD = 3V, RL = 16 10 20 Hz 0.1 1 20 Hz THD+N (%) THD+N (%) 1 20 kHz 0.01 20 kHz 0.1 0.01 1 kHz 1 kHz 0.001 1m 10m 20m 0.001 1m 100m 10m 20m OUTPUT POWER (W) Figure 28. 10 100m OUTPUT POWER (W) Figure 29. THD+N vs Output Power VDD = 2.4V, RL = 16 Power Derating Curve 0.6 POWER DISSIPATION (W) 20 Hz THD+N (%) 1 20 kHz 0.1 0.01 0.001 1m 1 kHz 0.5 0.4 0.3 0.2 0.1 0 10m 20m 100m OUTPUT POWER (W) 20 40 60 80 100 120 140 160 AMBIENT TEMPERATURE (C) Figure 30. 10 0 Figure 31. Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4929 LM4929 www.ti.com SNAS293B - DECEMBER 2004 - REVISED APRIL 2013 APPLICATION INFORMATION AMPLIFIER CONFIGURATION EXPLANATION As shown in Figure 1, the LM4929 has three operational amplifiers internally. Two of the amplifier's have externally configurable gain while the other amplifier is internally fixed at the bias point acting as a unity-gain buffer. The closed-loop gain of the two configurable amplifiers is set by selecting the ratio of Rf to Ri. Consequently, the gain for each channel of the IC is AVD = -(Rf / Ri) (1) By driving the loads through outputs VoA and VoB with VoC acting as a buffered bias voltage the LM4929 does not require output coupling capacitors. The classical single-ended amplifier configuration where one side of the load is connected to ground requires large, expensive output coupling capacitors. A configuration such as the one used in the LM4929 has a major advantage over single supply, single-ended amplifiers. Since the outputs VoA, VoB, and VoC are all biased at 1/2 VDD, no net DC voltage exists across each load. This eliminates the need for output coupling capacitors which are required in a single-supply, single-ended amplifier configuration. Without output coupling capacitors in a typical single-supply, single-ended amplifier, the bias voltage is placed across the load resulting in both increased internal IC power dissipation and possible loudspeaker damage. The LM4929 eliminates these output coupling capacitors by running in OCL mode. Unless shorted to ground, VoC is internally configured to apply a 1/2 VDD bias voltage to a stereo headphone jack's sleeve. This voltage matches the bias voltage present on VoA and VoB outputs that drive the headphones. The headphones operate in a manner similar to a bridge-tied load (BTL). Because the same DC voltage is applied to both headphone speaker terminals this results in no net DC current flow through the speaker. AC current flows through a headphone speaker as an audio signal's output amplitude increases on the speaker's terminal. The headphone jack's sleeve is not connected to circuit ground when used in OCL mode. Using the headphone output jack as a line-level output will place the LM4929's 1/2 VDD bias voltage on a plug's sleeve connection. This presents no difficulty when the external equipment uses capacitively coupled inputs. For the very small minority of equipment that is DC coupled, the LM4929 monitors the current supplied by the amplifier that drives the headphone jack's sleeve. If this current exceeds 500mAPK, the amplifier is shutdown, protecting the LM4929 and the external equipment. POWER DISSIPATION Power dissipation is a major concern when using any power amplifier and must be thoroughly understood to ensure a successful design. When operating in capacitor-coupled mode, Equation 2 states the maximum power dissipation point for a single-ended amplifier operating at a given supply voltage and driving a specified output load. PDMAX = (VDD) 2 / (22RL) (2) Since the LM4929 has three operational amplifiers in one package, the maximum power dissipation increases due to the use of the third amplifier as a buffer and is given in Equation 3: PDMAX = 4(VDD) 2 / (22RL) (3) The maximum power dissipation point obtained from Equation 3 must not be greater than the power dissipation that results from Equation 4: PDMAX = (TJMAX - TA) / JA (4) For package DGS, JA = 190C/W. TJMAX = 150C for the LM4929. Depending on the ambient temperature, TA, of the system surroundings, Equation 4 can be used to find the maximum internal power dissipation supported by the IC packaging. If the result of Equation 3 is greater than that of Equation 4, then either the supply voltage must be decreased, the load impedance increased or TA reduced. For the typical application of a 3V power supply, with a 32 load, the maximum ambient temperature possible without violating the maximum junction temperature is approximately 144C provided that device operation is around the maximum power dissipation point. Thus, for typical applications, power dissipation is not an issue. Power dissipation is a function of output power and thus, if typical operation is not around the maximum power dissipation point, the ambient temperature may be increased accordingly. Refer to the Typical Performance Characteristics for power dissipation information for lower output powers. Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4929 11 LM4929 SNAS293B - DECEMBER 2004 - REVISED APRIL 2013 www.ti.com POWER SUPPLY BYPASSING As with any amplifier, proper supply bypassing is important for low noise performance and high power supply rejection. The capacitor location on the power supply pins should be as close to the device as possible. Typical applications employ a 3V regulator with 10mF tantalum or electrolytic capacitor and a ceramic bypass capacitor which aid in supply stability. This does not eliminate the need for bypassing the supply nodes of the LM4929. A bypass capacitor value in the range of 0.1F to 1F is recommended for CS. MICRO POWER SHUTDOWN The voltage applied to the SHUTDOWN pin controls the LM4929's shutdown function. Activate micro-power shutdown by applying a logic-low voltage to the SHUTDOWN pin. When active, the LM4929's micro-power shutdown feature turns off the amplifier's bias circuitry, reducing the supply current. The trigger point varies depending on supply voltage and is shown in the Shutdown Hysteresis Voltage graphs in the Typical Performance Characteristics section. The low 0.1A(typ) shutdown current is achieved by applying a voltage that is as near as ground as possible to the SHUTDOWN pin. A voltage that is higher than ground may increase the shutdown current. There are a few ways to control the micro-power shutdown. These include using a single-pole, single-throw switch, a microprocessor, or a microcontroller. When using a switch, connect an external 100k pull-up resistor between the SHUTDOWN pin and VDD. Connect the switch between the SHUTDOWN pin and ground. Select normal amplifier operation by opening the switch. Closing the switch connects the SHUTDOWN pin to ground, activating micro-power shutdown. The switch and resistor ensure that the SHUTDOWN pin will not float. This prevents unwanted state changes. In a system with a microprocessor or microcontroller, use a digital output to apply the control voltage to the SHUTDOWN pin. Driving the SHUTDOWN pin with active circuitry eliminates the pull-up resistor. Shutdown enable/disable times are controlled by a combination of CB and VDD. Larger values of CB results in longer turn on/off times from Shutdown. Smaller VDD values also increase turn on/off time for a given value of CB. Longer shutdown times also improve the LM4929's resistance to click and pop upon entering or returning from shutdown. For a 2.4V supply and CB = 4.7F, the LM4929 requires about 2 seconds to enter or return from shutdown. This longer shutdown time enables the LM4929 to have virtually zero pop and click transients upon entering or release from shutdown. Smaller values of CB will decrease turn-on time, but at the cost of increased pop and click and reduced PSRR. Since shutdown enable/disable times increase dramatically as supply voltage gets below 2.2V, this reduced turnon time may be desirable if extreme low supply voltage levels are used as this would offset increases in turn-on time caused by the lower supply voltage. This technique is not recommended for OCL mode since shutdown enable/disable times are very fast (0.5s) independent of supply voltage. PROPER SELECTION OF EXTERNAL COMPONENTS Proper selection of external components in applications using integrated power amplifiers is critical to optimize device and system performance. While the LM4929 is tolerant of external component combinations, consideration to component values must be used to maximize overall system quality. The LM4929 is unity-gain stable which gives the designer maximum system flexibility. The LM4929 should be used in low gain configurations to minimize THD+N values, and maximize the signal to noise ratio. Low gain configurations require large input signals to obtain a given output power. Input signals equal to or greater than 1Vrms are available from sources such as audio codecs. Very large values should not be used for the gain-setting resistors. Values for Ri and Rf should be less than 1M. Please refer to the section, AUDIO POWER AMPLIFIER DESIGN, for a more complete explanation of proper gain selection Besides gain, one of the major considerations is the closed-loop bandwidth of the amplifier. To a large extent, the bandwidth is dictated by the choice of external components shown in Figure 2. The input coupling capacitor, Ci, forms a first order high pass filter which limits low frequency response. This value should be chosen based on needed frequency response and turn-on time. SELECTION OF INPUT CAPACITOR SIZE Amplifying the lowest audio frequencies requires a high value input coupling capacitor, Ci. A high value capacitor can be expensive and may compromise space efficiency in portable designs. In many cases, however, the headphones used in portable systems have little ability to reproduce signals below 60Hz. Applications using headphones with this limited frequency response reap little improvement by using a high value input capacitor. 12 Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4929 LM4929 www.ti.com SNAS293B - DECEMBER 2004 - REVISED APRIL 2013 In addition to system cost and size, turn on time is affected by the size of the input coupling capacitor Ci. A larger input coupling capacitor requires more charge to reach its quiescent DC voltage. This charge comes from the output via the feedback Thus, by minimizing the capacitor size based on necessary low frequency response, turn-on time can be minimized. A small value of Ci (in the range of 0.1F to 0.39F), is recommended. AUDIO POWER AMPLIFIER DESIGN A 25mW/32 AUDIO AMPLIFIER Given: Power Output 25mWrms Load Impedance 32 Input Level 1Vrms Input Impedance 20k A designer must first determine the minimum supply rail to obtain the specified output power. By extrapolating from the Output Power vs Supply Voltage graphs in the Typical Performance Characteristics section, the supply rail can be easily found. 3V is a standard voltage in most applications, it is chosen for the supply rail. Extra supply voltage creates headroom that allows the LM4929 to reproduce peak in excess of 25mW without producing audible distortion. At this time, the designer must make sure that the power supply choice along with the output impedance does not violate the conditions explained in the POWER DISSIPATION section. Once the power dissipation equations have been addressed, the required gain can be determined from Equation 5. (5) From Equation 5, the minimum AV is 0.89; use AV = 1. Since the desired input impedance is 20k, and with a AV gain of 1, a ratio of 1:1 results from Equation 1 for Rf to Ri. The values are chosen with Ri = 20k and Rf = 20k. The final design step is to address the bandwidth requirements which must be stated as a pair of -3dB frequency points. Five times away from a -3dB point is 0.17dB down from passband response which is better than the required 0.25dB specified. fL = 100Hz/5 = 20Hz fH = 20kHz * 5 = 100kHz As stated in the External Components section, Ri in conjunction with Ci creates a Ci 1 / (2 * 20k * 20Hz) = 0.397F; use 0.39F. The high frequency pole is determined by the product of the desired frequency pole, fH, and the differential gain, AV. With an AV = 1 and fH = 100kHz, the resulting GBWP = 100kHz which is much smaller than the LM4929 GBWP of 10MHz. This figure displays that is a designer has a need to design an amplifier with higher differential gain, the LM4929 can still be used without running into bandwidth limitations. Figure 32 shows an optional resistor connected between the amplifier output that drives the headphone jack sleeve and ground. This resistor provides a ground path that supressed power supply hum. Thishum may occur in applications such as notebook computers in a shutdown condition and connected to an external powered speaker. The resistor's 100 value is a suggested starting point. Its final value must be determined based on the tradeoff between the amount of noise suppression that may be needed and minimizing the additional current drawn by the resistor (25mA for a 100 resistor and a 5V supply). ESD PROTECTION As stated in the Absolute Maximum Ratings, the LM4929 has a maximum ESD susceptibility rating of 2000V. For higher ESD voltages, the addition of a PCDN042 dual transil (from California Micro Devices), as shown in Figure 32, will provide additional protection. Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4929 13 LM4929 SNAS293B - DECEMBER 2004 - REVISED APRIL 2013 www.ti.com Figure 32. The PCDN042 provides additional ESD protection beyond the 2000V shown in the Absolute Maximum Ratings for the VOC output 14 Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4929 LM4929 www.ti.com SNAS293B - DECEMBER 2004 - REVISED APRIL 2013 REVISION HISTORY Changes from Revision A (April 2013) to Revision B * Page Changed layout of National Data Sheet to TI format .......................................................................................................... 14 Submit Documentation Feedback Copyright (c) 2004-2013, Texas Instruments Incorporated Product Folder Links: LM4929 15 PACKAGE OPTION ADDENDUM www.ti.com 9-Aug-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty LM4929MM/NOPB ACTIVE VSSOP DGS 10 LM4929MMX/NOPB ACTIVE VSSOP DGS 10 3500 Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (C) Device Marking (3) (4/5) TBD Call TI Call TI GB9 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM GB9 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 Samples PACKAGE MATERIALS INFORMATION www.ti.com 12-Aug-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device LM4929MMX/NOPB Package Package Pins Type Drawing VSSOP DGS 10 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 3500 330.0 12.4 Pack Materials-Page 1 5.3 B0 (mm) K0 (mm) P1 (mm) 3.4 1.4 8.0 W Pin1 (mm) Quadrant 12.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 12-Aug-2013 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LM4929MMX/NOPB VSSOP DGS 10 3500 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2013, Texas Instruments Incorporated