© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 6/11/2012 1
One WORLD One Brand One Strategy One Focus One Team One KEMET
Benets
• AEC–Q200 automotive qualied
• -55°C to +125°C operating temperature range
• Pb-Free and RoHS Compliant
• Temperature stable dielectric
• EIA 0402, 0603, 0805, 1206, 1210, 1812, and 2220, case sizes
• DC voltage ratings of 6.3 V, 10 V, 16 V, 25 V, 50 V, 100 V,
200 V, and 250 V
• Capacitance offerings ranging from 150 pF to 22 μF
• Available capacitance tolerances of ±5%, ±10%, and ±20%
• Non-polar device, minimizing installation concerns
• 100% pure matte tin-plated termination nish allowing for
excellent solderability
Applications
Typical applications include decoupling, bypass, ltering and
transient voltage suppression.
Overview
KEMET’s Automotive Grade Series surface mount capacitors in
X7R dielectric are suited for a variety of applications requiring
reliable operation. Whether under-hood or in-cabin, these devices
emphasize the vital and robust nature of capacitors required for
mission and safety critical automotive circuits. Stricter testing
protocol and inspection criteria have been established for
automotive grade products in recognition of potentially harsh
environmental conditions. KEMET Automotive Grade series
capacitors meet the demanding Automotive Electronics Council's
AEC–Q200 qualication requirements and are manufactured in
state of the art ISO/TS 16949:2002 certied facilities.
X7R dielectric features a 125°C maximum operating temperature
and is considered “temperature stable,” The Electronics
Components, Assemblies and Materials Association (EIA)
characterizes X7R dielectric as a Class II material. Components of
this classication are xed, ceramic dielectric capacitors suited for
bypass and decoupling applications or for frequency discriminating
circuits where Q and stability of capacitance characteristics are
not critical. X7R exhibits a predictable change in capacitance
with respect to time and voltage and boasts a minimal change in
capacitance with reference to ambient temperature. Capacitance
change is limited to ±15% from -55°C to +125°C.
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs)
X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
Ordering Information
C0805 C225 M 4 R A CAUTO
Ceramic Case Size
(L" x W")
Specication/
Series
Capacitance
Code (pF)
Capacitance
Tolerance Voltage Dielectric Failure Rate/
Design Termination Finish1Packaging/Grade
(C-Spec)3
0402
0603
0805
1206
1210
1812
2220
C = Standard 2 Signicant Digits
+ Number of Zeros
J = ±5%
K = ±10%
M = ±20%
9 = 6.3 V
8 = 10 V
4 = 16 V
3 = 25 V
5 = 50 V
1 = 100 V
2 = 200 V
A = 250 V
R = X7R A = N/A C = 100% Matte Sn AUTO = Automotive
Grade 7" Reel
Unmarked
1 Additional termination nish options may be available. Contact KEMET for details
2 Additional reeling or packaging options may be available. Contact KEMET for details.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 6/11/2012 2
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) – X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
Dimensions – Millimeters (Inches)
EIA
Size
Code
Metric
Size
Code
L
Length
W
Width
T
Thickness
B
Bandwidth
S
Separation
Minimum
Mounting
Technique
0402 1005 1.00 (.040) ± 0.05 (.002) 0.50 (.020) ± 0.05 (.002)
See Table 2 for
Thickness
0.30 (.012) ± 0.10 (.004) 0.30 (.012) Solder Reow Only
0603 1608 1.60 (.063) ± 0.15 (.006) 0.80 (.032) ± 0.15 (.006) 0.35 (.014) ± 0.15 (.006) 0.70 (.028) Solder Wave or
Solder Reow
0805 2012 2.00 (.079) ± 0.20 (.008) 1.25 (.049) ± 0.20 (.008) 0.50 (0.02) ± 0.25 (.010) 0.75 (.030)
1206 3216 3.20 (.126) ± 0.20 (.008) 1.60 (.063) ± 0.20 (.008) 0.50 (0.02) ± 0.25 (.010)
N/A
1210 3225 3.20 (.126) ± 0.20 (.008) 2.50 (.098) ± 0.20 (.008) 0.50 (0.02) ± 0.25 (.010)
Solder Reow Only1812 4532 4.50 (.177) ± 0.30 (.012) 3.20 (.126) ± 0.30 (.012) 0.60 (.024) ± 0.35 (.014)
2220 5650 5.70 (.224) ± 0.40 (.016) 5.00 (.197) ± 0.40 (.016) 0.60 (.024) ± 0.35 (.014)
Qualication/Certication
Automotive Grade products meet or exceed the requirements outlined by the Automotive Electronics Council. Details regarding test
methods and conditions are referenced in document AEC–Q200, Stress Test Qualication for Passive Components. For additional
information regarding the Automotive Electronics Council and AEC–Q200, please visit their website at www.aecouncil.com.
Environmental Compliance
Pb-Free and RoHS Compliant.
Ceramic Surface Mount
WL
TB
S
100% Tin or SnPb Plate
Nickel Plate
Conductive Metalization
Electrodes
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 6/11/2012 3
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) – X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
Electrical Parameters/Characteristics
Item Parameters/Characteristics
Operating Temperature Range -55°C to +125°C
Capacitance Change with Reference to +25°C and 0 VDC Applied (TCC) ±15%
Aging Rate (Maximum % Capacitance Loss/Decade Hour) 3.0%
Dielectric Withstanding Voltage (DWV)
250% of rated voltage
(5 ±1 seconds and charge/discharge not exceeding 50 mA)
Dissipation Factor (DF) Maximum Limit @ 25ºC 5%(10 V), 3.5%(16 and 25 V) and 2.5%(50 to 250 V)
Insulation Resistance (IR) Limit @ 25°C
See Insulation Resistance Limit Table
(Rated voltage applied for 120 ±5 seconds @ 25°C)
Regarding aging rate: Capacitance measurements (including tolerance) are indexed to a referee time of 1,000 hours.
To obtain IR limit, divide MΩ-µF value by the capacitance and compare to GΩ limit. Select the lower of the two limits.
Capacitance and dissipation factor (DF) measured under the following conditions:
1 kHz ±50 Hz and 1.0 ±0.2 Vrms if capacitance ≤ 10 µF
120 Hz ±10 Hz and 0.5 ±0.1 Vrms if capacitance >10 µF
Note: When measuring capacitance it is important to ensure the set voltage level is held constant. The HP4284 and Agilent E4980 have a feature known as
Automatic Level Control (ALC). The ALC feature should be switched to "ON."
Post Environmental Limits
High Temperature Life, Biased Humidity, Moisture Resistance
Dielectric Rated DC
Voltage Capacitance
Value
Dissipation Factor
(Maximum %) Capacitance
Shift
Insulation
Resistance
X7R
> 25
All
3.0
± 20% 10% of Initial Limit16/25 5.0
< 16 7.5
Insulation Resistance Limit Table
EIA Case Size
1,000 Megohm
Microfarads or 100 GΩ
500 Megohm
Microfarads or 10 GΩ
0201 N/A ALL
0402 < 0.012 µF ≥ 0.012 µF
0603 < 0.047 µF ≥ 0.047 µF
0805 < 0.047 µF ≥ 0.047 µF
1206 < 0.22 µF ≥ 0.22 µF
1210 < 0.39 µF ≥ 0.39 µF
1808 ALL N/A
1812 < 2.2 µF ≥ 2.2 µF
1825 ALL N/A
2220 < 10 µF ≥ 10 µF
2225 ALL N/A
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 6/11/2012 4
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) – X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
Cap Cap
Code
Series C0402 C0603 C0805 C1206
Voltage Code 9843 5 98435129843512A9843512A
Voltage DC
6.3
10
16
25
50
6.3
10
16
25
50
100
200
6.3
10
16
25
50
100
200
250
6.3
10
16
25
50
100
200
250
Cap Tolerance Product Availability and Chip Thickness Codes – See Table 2 for Chip Thickness Dimensions
10 – 91 pF 100 – 910 J K M BB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC EB EB EB EB EB EB EB
100 – 150 pF 101 – 821 J K M BB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC EB EB EB EB EB EB EB
180 – 820 pF 181 J K MBB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB
1,000 pF 102 J K M BB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB
1,200 pF 122 J K M BB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB
1,500 pF 152 J K M BB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB
1,800 pF 182 J K M BB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB
2,200 pF 222 J K M BB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB
2,700 pF 272 J K M BB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB
3,300 pF 332 J K M BB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB
3,900 pF 392 J K M BB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB
4,700 pF 472 J K M BB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB
5,600 pF 562 J K M BB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB
6,800 pF 682 J K M BB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB
8,200 pF 822 J K M BB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB
10,000 pF 103 J K M BB BB BB BB BB CB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB
12,000 pF 123 J K M BB BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DC DC DC EB EB EB EB EB EB EB EB
15,000 pF 153 J K M BB BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DD DC DC EB EB EB EB EB EB EB EB
18,000 pF 183 J K M BB BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DD DC DC EB EB EB EB EB EB EB EB
22,000 pF 223 J K M BB BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DD DC DC EB EB EB EB EB EB EB EB
27,000 pF 273 J K M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DD DE EB EB EB EB EB EB EB EB
33,000 pF 333 J K M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DD DE EB EB EB EB EB EB EB EB
39,000 pF 393 J K M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DD DE EB EB EB EB EB EC EB EB
47,000 pF 473 J K M BB BB BB BB CB CB CB CB CB CB DC DC DC DC DC DE DG EB EB EB EB EB EC ED ED
56,000 pF 563 J K M BB BB BB CB CB CB CB CB DD DD DD DD DD DE DG EB EB EB EB EB EB ED ED
68,000 pF 683 J K M BB BB BB CB CB CB CB CB DD DD DD DD DD DE EB EB EB EB EB EB ED ED
82,000 pF 823 J K M BB BB BB CB CB CB CB CB DD DD DD DD DD DE EB EB EB EB EB EB ED ED
0.10 uF 104 J K M BB BB BB CB CB CB CB CB DC DC DC DC DC DE EB EB EB EB EB EB EM EM
0.12 uF 124 J K M CB CB CB CB CB DC DC DC DC DD DG EC EC EC EC EC EC EG
0.15 uF 154 J K M CB CB CB CB CB DC DC DC DC DD DG EC EC EC EC EC EC EG
0.18 uF 184 J K M CB CB CB CB DC DC DC DC DD DG EC EC EC EC EC EC
0.22 uF 224 J K M CB CB CB CD DC DC DC DC DD DG EC EC EC EC EC EC
0.27 uF 274 J K M CB CB CB DD DD DD DD DD EB EB EB EB EC EM
0.33 uF 334 J K M CB CB CB DD DD DD DD DD EB EB EB EB EC EG
0.39 uF 394 J K M CB CB CB DG DG DG DG DE EB EB EB EB EC EG
0.47 uF 474 J K M CB CB CB DD DD DD DD DE EC EC EC EC EC EG
0.56 uF 564 J K M DD DD DD DG DH ED ED ED ED EC
0.68 uF 684 J K M DD DD DD DG DH EE EE EE EE ED
0.82 uF 824 J K M DD DD DD DG EF EF EF EF ED
1.0 uF 105 J K M DD DD DD DG EF EF EF EG ED
1.2 uF 125 J K M DE DE DE ED ED ED EG EH
1.5 uF 155 J K M DG DG DG EF EF EF EG EH
1.8 uF 185 J K M DG DG DG ED ED ED EF EH
2.2 uF 225 J K M DG DG DG ED ED ED EF EH
2.7 uF 275 J K M EN EN EN EH
3.3 uF 335 J K M ED ED ED EH
3.9 uF 395 J K M EF EF EF EH
4.7 uF 475 J K M EF EF EF EH
5.6 uF 565 J K M EH EH EH
6.8 uF 685 J K M EH EH EH
8.2 uF 825 J K M EH EH EH
10 uF 106 J K M EH EH EH
12 uF 126 J K M
Cap Cap
Code
Voltage DC
6.3
10
16
25
50
6.3
10
16
25
50
100
200
6.3
10
16
25
50
100
200
250
6.3
10
16
25
50
100
200
250
Voltage Code 9843 5 98435129843512A 9 843512A
Series C0402 C0603 C0805 C1206
Table 1A – Capacitance Range/Selection Waterfall (0402 – 1206 Case Sizes)
Roll Over for
Order Info.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 6/11/2012 5
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) – X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
Table 1B – Capacitance Range/Selection Waterfall (1210 – 2220 Case Sizes)
Cap Cap
Code
Series C1210 C1812 C1825 C2220
Voltage Code 9843512A3 5 12A512A3 5 12A
Voltage DC
6.3
10
16
25
50
100
200
250
25
50
100
200
250
50
100
200
250
25
50
100
200
250
Cap Tolerance Product Availability and Chip Thickness Codes - See Table 2 for Chip Thickness Dimensions
10 – 91 pF 100 – 910 J K M FB FB FB FB FB FB FB
100 – 390 pF 101 – 391 J K M FB FB FB FB FB FB FB
470 – 820 pF 471 – 821 J K M FB FB FB FB FB FB FB GB GB GB GB
1,000 pF 102 J K M FB FB FB FB FB FB FB GB GB GB GB
1,200 pF 122 J K M FB FB FB FB FB FB FB GB GB GB GB
1,500 pF 152 J K M FB FB FB FB FB FB FE GB GB GB GB
1,800 pF 182 J K M FB FB FB FB FB FB FE GB GB GB GB
2,200 pF 222 J K M FB FB FB FB FB FB FB FB GB GB GB GB
2,700 pF 272 J K M FB FB FB FB FB FB FB FB GB GB GB GB
3,300 pF 332 J K M FB FB FB FB FB FB FB FB GB GB GB GB
3,900 pF 392 J K M FB FB FB FB FB FB FB FB GB GB GB GB
4,700 pF 472 J K M FB FB FB FB FB FB FB FB GB GB GB GD
5,600 pF 562 J K M FB FB FB FB FB FB FB FB GB GB GB GH
6,800 pF 682 J K M FB FB FB FB FB FB FB FB GB GB GB GB GB JE JE JE
8,200 pF 822 J K M FB FB FB FB FB FB FB FB GB GB GB GB GB JE JE JE
10,000 pF 103 J K M FB FB FB FB FB FB FB FB GB GB GB GB GB JE JE JE
12,000 pF 123 J K M FB FB FB FB FB FB FB FB GB GB GB GB GB JE JE JE
15,000 pF 153 J K M FB FB FB FB FB FB FB FB GB GB GB GB GB JE JE JE
18,000 pF 183 J K M FB FB FB FB FB FB FB FB GB GB GB GB GB JE JE JE
22,000 pF 223 J K M FB FB FB FB FB FB FB FB GB GB GB GB GB HB HB HB HB JE JE JE
27,000 pF 273 J K M FB FB FB FB FB FB FB FB GB GB GB GB GB HB HB HB HB JE JE JE
33,000 pF 333 J K M FB FB FB FB FB FB FB FB GB GB GB GB GB HB HB HB HB JB JB JB
39,000 pF 393 J K M FB FB FB FB FB FB FB FB GB GB GB GB GB HB HB HB HB JB JB JB
47,000 pF 473 J K M FB FB FB FB FB FB FB FB GB GB GB GB GB HB HB HB HB JB JB JB
56,000 pF 563 J K M FB FB FB FB FB FB FC FC GB GB GB GB GB HB HB HB HB JB JB JB
68,000 pF 683 J K M FB FB FB FB FB FB FC FC GB GB GB GB GB HB HB HB HB JB JB JB
82,000 pF 823 J K M FB FB FB FB FB FC FF FF GB GB GB GB GB HB HB HB HB JB JB JC JC JC
0.10 uF 104 J K M FB FB FB FB FB FD FG FG GB GB GB GB GB HB HB HB HB JB JB JC JC JC
0.12 uF 124 J K M FB FB FB FB FB FD GB GB GB GB GB HB HB HB HB JB JB JC JC JC
0.15 uF 154 J K M FC FC FC FC FC FD GB GB GB GE GE HB HB HB HB JB JB JC JC JC
0.18 uF 184 JK M FC FC FC FC FC FD GB GB GB GG GG HB HB HB HB JB JB JC JC JC
0.22 uF 224 J K M FC FC FC FC FC FD GB GB GB GG GG HB HB HB HB JB JB JC JC JC
0.27 uF 274 J K M FC FC FC FC FC FD GB GB GG GG GG HB HB HB HB JC JC JC JC JC
0.33 uF 334 J K M FD FD FD FD FD FD GB GB GG GG GG HB HB HB HB JC JC JC JC JC
0.39 uF 394 J K M FD FD FD FD FD FD GB GB GG GG GG HD HD HD HD JC JC JC JC JC
0.47 uF 474 J K M FD FD FD FD FD FD GB GB GG GJ GJ HD HD HD HD JC JC JC JC JC
0.56 uF 564 J K M FD FD FD FD FD FF GC GC GG HD HD HD HD JC JD JD JD JD
0.68 uF 684 J K M FD FD FD FD FD FG GC GC GG HD HD HD HD JC JD JD JD JD
0.82 uF 824 J K M FF FF FF FF FF FL GE GE GG HF HF HF HF JC JF JF JF JF
1.0 uF 105 J K M FH FH FH FH FH FM GE GE GG HF HF HF HF JC JF JF JF JF
1.2 uF 125 J K M FH FH FH FH FG JC JC
1.5 uF 155 J K M FH FH FH FH FG JC JC
1.8 uF 185 J K M FH FH FH FH FG JD JD
2.2 uF 225 J K M FJ FJ FJ FJ FG GO GO JF JF
2.7 uF 275 J K M FE FE FE FG FH
3.3 uF 335 J K M FF FF FF FM FM
3.9 uF 395 J K M FG FG FG FG FK
4.7 uF 475 J K M FC FC FC FG FS GK GK
5.6 uF 565 J K M FF FF FF FH
6.8 uF 685 J K M FG FG FG FM
8.2 uF 825 J K M FH FH FH FK
10 uF 106 J K M FH FH FH FS GK JF JO
12 uF 126 J K M
15 uF 156 J K M JO
18 uF 186 J K M
22 uF 226 J K M FS FS JO
Cap Cap
Code
Voltage DC
6.3
10
16
25
50
100
200
250
25
50
100
200
250
50
100
200
250
25
50
100
200
250
Voltage Code 9843512A3 5 12A512A3 5 12A
Series C1210 C1812 C1825 C2220
Roll Over for
Order Info.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 6/11/2012 6
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) – X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
Table 2 – Chip Thickness/Packaging Quantities
Thickness
Code
Case
Size Thickness ±
Range (mm)
Paper Quantity Plastic Quantity
7" Reel 13" Reel 7" Reel 13" Reel
BB
0402
0.50 ± 0.05
CB
0603
0.80 ± 0.07
CD
0603
0.80 ± 0.15
DC
0805
0.78 ± 0.10
DD
0805
0.90 ± 0.10
DE
0805
1.00 ± 0.10
DG
0805
1.25 ± 0.15
DH
0805
1.25 ± 0.20
EB
1206
0.78 ± 0.10
EC
1206
0.90 ± 0.10
EN
1206
0.95 ± 0.10
ED
1206
1.00 ± 0.10
EE
1206
1.10 ± 0.10
EF
1206
1.20 ± 0.15
EM
1206
1.25 ± 0.15
EG
1206
1.60 ± 0.15
EH
1206
1.60 ± 0.20
FB
1210
0.78 ± 0.10
FC
1210
0.90 ± 0.10
FD
1210
0.95 ± 0.10
FE
1210
1.00 ± 0.10
FF
1210
1.10 ± 0.10
FG
1210
1.25 ± 0.15
FL
1210
1.40 ± 0.15
FH
1210
1.55 ± 0.15
FM
1210
1.70 ± 0.20
FJ
1210
1.85 ± 0.20
FK
1210
2.10 ± 0.20
FS
1210
2.50 ± 0.20
NA
1706
0.90 ± 0.10
NC
1706
1.00 ± 0.15
LD
1808
0.90 ± 0.10
LF
1808
1.00 ± 0.15
GB
1812
1.00 ± 0.10
GC
1812
1.10 ± 0.10
GD
1812
1.25 ± 0.15
GE
1812
1.30 ± 0.10
GH
1812
1.40 ± 0.15
GG
1812
1.55 ± 0.10
GK
1812
1.60 ± 0.20
GJ
1812
1.70 ± 0.15
GO
1812
2.50 ± 0.20
HB
1825
1.10 ± 0.15
HD
1825
1.30 ± 0.15
HF
1825
1.50 ± 0.15
JB
2220
1.00 ± 0.15
JC
2220
1.10 ± 0.15
JD
2220
1.30 ± 0.15
JE
2220
1.40 ± 0.15
JF
2220
1.50 ± 0.15
JO
2220
2.40 ± 0.15
Thickness
Code Case
Size Thickness ±
Range (mm)
7" Reel 13" Reel 7" Reel 13" Reel
Paper Quantity Plastic Quantity
Package quantity based on nished chip thickness specications
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 6/11/2012 7
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) – X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
Table 3 – Chip Capacitor Land Pattern Design Recommendations per IPC–7351
EIA
Size
Code
Metric
Size
Code
Density Level A:
Maximum (Most)
Land Protrusion (mm)
Density Level B:
Median (Nominal)
Land Protrusion (mm)
Density Level C:
Minimum (Least)
Land Protrusion (mm)
CY X V1 V2 CY X V1 V2 CY X V1 V2
01005 0402 0.33 0.46 0.43 1.60 0.90 0.28 0.36 0.33 1.30 0.70 0.23 0.26 0.23 1.00 0.50
0201 0603 0.38 0.56 0.52 1.80 1.00 0.33 0.46 0.42 1.50 0.80 0.28 0.36 0.32 1.20 0.60
0402 1005 0.50 0.72 0.72 2.20 1.20 0.45 0.62 0.62 1.90 1.00 0.40 0.52 0.52 1.60 0.80
0603 1608 0.90 1.15 1.10 4.00 2.10 0.80 0.95 1.00 3.10 1.50 0.60 0.75 0.90 2.40 1.20
0805 2012 1.00 1.35 1.55 4.40 2.60 0.90 1.15 1.45 3.50 2.00 0.75 0.95 1.35 2.80 1.70
1206 3216 1.60 1.35 1.90 5.60 2.90 1.50 1.15 1.80 4.70 2.30 1.40 0.95 1.70 4.00 2.00
1210 3225 1.60 1.35 2.80 5.65 3.80 1.50 1.15 2.70 4.70 3.20 1.40 0.95 2.60 4.00 2.90
1808 4520 2.30 1.75 2.30 7.40 3.30 2.20 1.55 2.20 6.50 2.70 2.10 1.35 2.10 5.80 2.40
1812 4532 2.15 1.60 3.60 6.90 4.60 2.05 1.40 3.50 6.00 4.00 1.95 1.20 3.40 5.30 3.70
1825 4564 2.15 1.60 6.90 6.90 7.90 2.05 1.40 6.80 6.00 7.30 1.95 1.20 6.70 5.30 7.0 0
2220 5650 2.75 1.70 5.50 8.20 6.50 2.65 1.50 5.40 7.30 5.90 2.55 1.30 5.30 6.60 5.60
2225 5664 2.70 1.70 6.90 8.10 7.90 2.60 1.50 6.80 7.20 7.30 2.50 1.30 6.70 6.50 7.00
Density Level A: For low-density product applications. Recommended for wave solder applications and provides a wider process window for reow solder
processes. KEMET only recommends wave soldering of EIA 0603, 0805, and 1206 case sizes.
Density Level B: For products with a moderate level of component density. Provides a robust solder attachment condition for reow solder processes.
Density Level C: For high component density product applications. Before adapting the minimum land pattern variations the user should perform qualication
testing based on the conditions outlined in IPC Standard 7351 (IPC–7351).
Soldering Process
Recommended Soldering Technique:
• Solder wave or solder reow for EIA case sizes 0603, 0805, and 1206
• All other EIA case sizes are limited to solder reow only
Recommended Soldering Prole:
• KEMET recommends following the guidelines outlined in IPC/JEDEC J–STD–020
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 6/11/2012 8
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) – X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
Table 4 – Performance & Reliability: Test Methods and Conditions
Stress Reference Test or Inspection Method
Terminal Strength JIS–C–6429 Appendix 1, Note: Force of 1.8 kg for 60 seconds.
Board Flex JIS–C–6429 Appendix 2, Note: 2 mm (min) for all except 3 mm for C0G.
Solderability J–STD–002
Magnication 50 X. Conditions:
a) Method B, 4 hours @ 155°C, dry heat @ 235°C
b) Method B @ 215°C category 3
c) Method D, category 3 @ 260°C
Temperature Cycling JESD22 Method JA–104 1,000 cycles (-55°C to +125°C). Measurement at 24 hours +/- 2 hours after test conclusion.
Biased Humidity MIL–STD–202 Method 103
Load Humidity: 1,000 hours 85°C / 85% RH and 300 VDC maximum. Add 100 K ohm resistor.
Measurement at 24 hours +/- 2 hours after test conclusion.
Low Volt Humidity: 1,000 hours 85°C / 85%RH and 1.5 V. Add 100 K ohm resistor. Measurement at
24 hours +/- 2 hours after test conclusion.
Moisture Resistance MIL–STD–202 Method 106
t = 24 hours/cycle. Steps 7a and 7b not required. Unpowered. Measurement at 24 hours +/- 2 hours
after test conclusion.
Thermal Shock MIL–STD–202 Method 107
-55°C / +125°C. Note: Number of cycles required – 300. Maximum transfer time – 20 seconds.
Dwell time – 15 minutes. Air – Air.
High Temperature Life MIL–STD–202 Method 108 1,000 hours at 125°C (85°C for X5R, Z5U and Y5V) with rated voltage applied.
Storage Life MIL–STD–202 Method 108 150°C, 0 VDC for 1,000 hours.
Mechanical Shock MIL–STD–202 Method 213 Figure 1 of Method 213, Condition F.
Resistance to Solvents MIL–STD–202 Method 215 Add aqueous wash chemical, OKEM Clean or equivalent.
Storage and Handling
Ceramic chip capacitors should be stored in normal working environments. While the chips themselves are quite robust in other
environments, solderability will be degraded by exposure to high temperatures, high humidity, corrosive atmospheres, and long term
storage. In addition, packaging materials will be degraded by high temperature– reels may soften or warp and tape peel force may
increase. KEMET recommends that maximum storage temperature not exceed 40ºC and maximum storage humidity not exceed 70%
relative humidity. Temperature uctuations should be minimized to avoid condensation on the parts and atmospheres should be free of
chlorine and sulfur bearing compounds. For optimized solderability chip stock should be used promptly, preferably within 1.5 years of
receipt.
Construction
Reference Item Material
ATermination
System
Finish 100% Matte Sn
B Barrier Layer Ni
CBase Metal Cu
DInner Electrode Ni
EDielectric Material BaTiO3
Note: Image is exaggerated in order to clearly identify all components of construction.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 6/11/2012 9
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) – X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
Tape & Reel Packaging Information
KEMET offers multilayer ceramic chip capacitors packaged in 8, 12 and 16 mm tape on 7" and 13" reels in accordance with EIA
Standard 481. This packaging system is compatible with all tape-fed automatic pick and place systems. See Table 2 for details on
reeling quantities for commercial chips.
8 mm, 12 mm
or 16 mm Carrier Tape
178 mm (7.00")
or
330 mm (13.00")
Anti-Static Reel
Embossed Plastic* or
Punched Paper Carrier.
Embossment or Punched Cavity
Anti-Static Cover Tape
(.10 mm (.004") Maximum Thickness)
Chip and KPS Orientation in Pocket
(except 1825 Commercial, and 1825 and 2225 Military)
*EIA 01005, 0201, 0402 and 0603 case sizes available on punched paper carrier only.
KEMET
®
Bar Code Label
Sprocket Holes
Table 5 – Carrier Tape Con guration – Embossed Plastic & Punched Paper (mm)
EIA Case Size Tape Size (W)* Lead Space (P
1
)*
01005 – 0402 8 2
0603 – 1210 8 4
1805 – 1808 12 4
≥ 1812 12 8
KPS 1210 12 8
KPS 1812 & 2220 16 12
Array 0508 & 0612 8 4
*Refer to Figures 1 & 2 for W and P1 carrier tape reference locations.
*Refer to Tables 6 & 7 for tolerance speci cations.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 6/11/2012 10
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) – X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
Figure 1 – Embossed (Plastic) Carrier Tape Dimensions
Po
T
F
W
Center Lines of Cavity
Ao
Bo
User Direction of Unreeling
Cover Tape
Ko
B
1
is for tape feeder reference only,
including draft concentric about B
o
.
T
2
ØD
1
ØDo
B
1
S
1
T
1
E
1
E
2
P
1
P
2
Embossment
For cavity size,
see Note 1 Table 5
[10 pitches cumulative
tolerance on tape ± 0.2 mm]
Table 6 – Embossed (Plastic) Carrier Tape Dimensions
Metric will govern
Constant Dimensions — Millimeters (Inches)
Tape Size D0
D
1
Minimum
Note 1
E1P0 P2
R Reference
Note 2
S
1
Minimum
Note 3
T
Maximum
T
1
Maximum
8 mm
1.5 +0.10/-0.0 (0.059
+0.004/-0.0)
1.0
(0.039)
1.75 ±0.10
(0.069 ±0.004)
4.0 ±0.10
(0.157 ±0.004)
2.0 ±0.05 (0.079
±0.002)
25.0
(0.984)
0.600
(0.024)
0.600
(0.024)
0.100
(0.004)
12 mm 1.5
(0.059)
30
(1.181)
16 mm
Variable Dimensions — Millimeters (Inches)
Tape Size Pitch
B
1
Maximum
Note 4
E
2
Minimum
F P1
T
2
Maximum
W
Maximum
A0,B0 & K0
8 mm Single (4 mm) 4.35
(0.171)
6.25
(0.246)
3.5 ±0.05
(0.138 ±0.002)
4.0 ±0.10
(0.157 ±0.004)
2.5
(0.098)
8.3
(0.327)
Note 512 mm Single (4 mm) &
Double (8 mm)
8.2
(0.323)
10.25
(0.404)
5.5 ±0.05
(0.217 ±0.002)
8.0 ±0.10 (0.315
±0.004)
4.6
(0.181)
12.3
(0.484)
16 mm Triple (12 mm) 12.1
(0.476)
14.25
(0.561)
5.5 ±0.05
(0.217 ±0.002)
8.0 ±0.10 (0.315
±0.004)
4.6
(0.181)
16.3
(0.642)
1. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and
hole location shall be applied independent of each other.
2. The tape with or without components shall pass around R without damage (see Figure 6).
3. If S1 < 1.0 mm, there may not be enough area for cover tape to be properly applied (see EIA Standard 481 paragraph 4.3 section b).
4. B1 dimension is a reference dimension for tape feeder clearance only.
5. The cavity de ned by A0, B0 and K0 shall surround the component with suf cient clearance that:
(a) the component does not protrude above the top surface of the carrier tape.
(b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed.
(c) rotation of the component is limited to 20° maximum for 8 and 12 mm tapes and 10° maximum for 16 mm tapes (see Figure 3).
(d) lateral movement of the component is restricted to 0.5 mm maximum for 8 and 12 mm wide tape and to 1.0 mm maximum for 16 mm tape (see Figure 4).
(e) for KPS Series product, A0 and B0 are measured on a plane 0.3 mm above the bottom of the pocket.
(f) see Addendum in EIA Standard 481 for standards relating to more precise taping requirements.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 6/11/2012 11
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) – X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
Figure 2 – Punched (Paper) Carrier Tape Dimensions
User Direction of Unreeling
Top Cover Tape
T
Center Lines of Cavity
P
1
ØDo Po
P
2
E
1
F
E
2
W
G
A
0
B
0
Cavity Size,
See
Note 1, Table 7
Bottom Cover Tape
T
1
T
1
Bottom Cover Tape
[10 pitches cumulative
tolerance on tape ± 0.2 mm]
Table 7 – Punched (Paper) Carrier Tape Dimensions
Metric will govern
Constant Dimensions — Millimeters (Inches)
Tape Size D0E1P0P2T1 Maximum G Minimum
R Reference
Note 2
8 mm 1.5 +0.10 -0.0
(0.059 +0.004 -0.0)
1.75 ±0.10
(0.069 ±0.004)
4.0 ±0.10
(0.157 ±0.004)
2.0 ±0.05
(0.079 ±0.002)
0.10
(0.004) Maximum
0.75
(0.030)
25
(0.984)
Variable Dimensions — Millimeters (Inches)
Tape Size Pitch E2 Minimum F P1 T Maximum W Maximum A0 B0
8 mm Half (2 mm) 6.25
(0.246)
3.5 ±0.05
(0.138 ±0.002)
2.0 ±0.05
(0.079 ±0.002)
1.1
(0.098)
8.3
(0.327)
Note 1
8 mm Single (4 mm)
4.0 ±0.10
(0.157 ±0.004)
8.3
(0.327)
1. The cavity de ned by A0, B0 and T shall surround the component with suf cient clearance that:
a) the component does not protrude beyond either surface of the carrier tape.
b) the component can be removed from the cavity in a vertical direction without mechanical restriction, after the top cover tape has been removed.
c) rotation of the component is limited to 20° maximum (see Figure 3).
d) lateral movement of the component is restricted to 0.5 mm maximum (see Figure 4).
e) see Addendum in EIA Standard 481 for standards relating to more precise taping requirements.
2. The tape with or without components shall pass around R without damage (see Figure 6).
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 6/11/2012 12
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) – X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
Packaging Information Performance Notes
1. Cover Tape Break Force: 1.0 Kg minimum.
2. Cover Tape Peel Strength: The total peel strength of the cover tape from the carrier tape shall be:
Tape Width Peel Strength
8 mm 0.1 to 1.0 Newton (10 to 100 gf)
12 and 16 mm 0.1 to 1.3 Newton (10 to 130 gf)
The direction of the pull shall be opposite the direction of the carrier tape travel. The pull angle of the carrier tape shall be 165° to 180°
from the plane of the carrier tape. During peeling, the carrier and/or cover tape shall be pulled at a velocity of 300 ±10 mm/minute.
3. Labeling: Bar code labeling (standard or custom) shall be on the side of the reel opposite the sprocket holes. Refer to EIA
Standards 556 and 624.
Figure 3 – Maximum Component Rotation
Ao
Bo
°
T
°
s
Maximum Component Rotation
Top View Maximum Component Rotation
Side View
Tape Maximum
Width (mm) Rotation (°
T)
8,12 20
16 – 200 10 Tape Maximum
Width (mm) Rotation ( °
S)
8,12 20
16 – 56 10
72 – 200 5
Typical Pocket Centerline
Typical Component Centerline
Figure 4 – Maximum Lateral Movement
0.5 mm maximum
0.5 mm maximum
8 mm & 12 mm Tape
1.0 mm maximum
1.0 mm maximum
16 mm Tape
Figure 5 – Bending Radius
RR
Bending
Radius
Embossed
Carrier Punched
Carrier
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 6/11/2012 13
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) – X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
Figure 6 – Reel Dimensions
AD(See Note)
Full Radius,
See Note
B(see Note)
Access Hole at
Slot Location
(Ø 40 mm minimum)
If present,
tape slot in core
for tape start:
2.5 mm minimum width x
10.0 mm minimum depth
W3(Includes
flange distortion
at outer edge)
W2(Measured at hub)
W1(Measured at hub)
C
(Arbor hole
diameter)
Note: Drive spokes optional; if used, dimensions B and D shall apply.
N
Table 8 – Reel Dimensions
Metric will govern
Constant Dimensions — Millimeters (Inches)
Tape Size A B Minimum CD Minimum
8 mm 178 ±0.20
(7.008 ±0.008)
or
330 ±0.20
(13.000 ±0.008)
1.5
(0.059)
13.0 +0.5/-0.2
(0.521 +0.02/-0.008)
20.2
(0.795)
12 mm
16 mm
Variable Dimensions — Millimeters (Inches)
Tape Size N Minimum W1 W2 Maximum W3
8 mm
50
(1.969)
8.4 +1.5/-0.0
(0.331 +0.059/-0.0)
14.4
(0.567)
Shall accommodate tape width
without interference
12 mm
12.4 +2.0/-0.0
(0.488 +0.078/-0.0)
18.4
(0.724)
16 mm
16.4 +2.0/-0.0
(0.646 +0.078/-0.0)
22.4
(0.882)
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 6/11/2012 14
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) – X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
Figure 7 – Tape Leader & Trailer Dimensions
Trailer
160 mm Minimum
Carrier Tape
END START
Round Sprocket Holes
Elongated Sprocket Holes
(32 mm tape and wider)
Top Cover Tape
Top Cover Tape
Punched Carrier
8 mm & 12 mm only
Embossed Carrier
Components
100 mm
Minimum Leader
400 mm Minimum
Figure 8 – Maximum Camber
Carrier Tape Round Sprocket Holes
1 mm Maximum, either direction
Straight Edge
250 mm
Elongated sprocket holes
(32 mm & wider tapes)
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 6/11/2012 15
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) – X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
Figure 9 – Bulk Cassette Packaging (Ceramic Chips Only)
Meets Dimensional Requirements IEC–286 and EIAJ 7201
Unit mm *Reference
110 ± 0.7
31.5 ± 0
0.2
36 ± 0
0.2
19.0*
5 0*
10*
53 3*
68 ± 0.1
88 ± 0.1
12.0 ± 0.1
3.0 ± 0
0.2
2.0 ± 0.1
0
1.5 ± 0
0.1
Table 9 – Capacitor Dimensions for Bulk Cassette
Cassette Packaging – Millimeters
EIA Size
Code
Metric Size
Code
L Length W Width B Bandwidth
S Separation
Minimum
T Thickness
Number of
Pieces/Cassette
0402 1005 1.0 ±0.05 0.5 ±0.05 0.2 to 0.4 0.3 0.5 ±0.05 50,000
0603 1608 1.6 ±0.07 0.8 ±0.07 0.2 to 0.5 0.7 0.8 ±0.07 15,000
Table 10 – Capacitor Marking
Laser marking is available as an extra-
cost option for most KEMET ceramic
chips. Such marking is two sided and
includes a K to identify KEMET, followed
by two characters (per EIA–198) to
identify the capacitance value. Note that
marking is not available for any Y5V chip.
ln addition, the 0603 marking option is
limited to the K only. (Marking Optional –
Not Available for 0402 Size)
Example shown is 1,000 pF capacitor
N u m e r a l
Alpha
Character
Capacitance (pF) For Various Numeral Identiers
9
0
1
2
3
4
5
6
7
A
0.1
1
10
100
1000
10000
100000
1000000
10000000
B
0.11
1.1
11
110
1100
11000
110000
1100000
11000000
C
0.12
1.2
12
120
1200
12000
120000
1200000
12000000
D
0.13
1.3
13
130
1300
13000
130000
1300000
13000000
E
0.15
1.5
15
150
1500
15000
150000
1500000
15000000
F
0.16
1.6
16
160
1600
16000
160000
1600000
16000000
G
0.18
1.8
18
180
1800
18000
180000
1800000
18000000
H
0.2
2
20
200
2000
20000
200000
2000000
20000000
J
0.22
2.2
22
220
2200
22000
220000
2200000
22000000
K
0.24
2.4
24
240
2400
24000
240000
2400000
24000000
L
0.27
2.7
27
270
2700
27000
270000
2700000
27000000
M
0.3
3
30
300
3000
30000
300000
3000000
30000000
N
0.33
3.3
33
330
3300
33000
330000
3300000
33000000
P
0.36
3.6
36
360
3600
36000
360000
3600000
36000000
Q
0.39
3.9
39
390
3900
39000
390000
3900000
39000000
R
0.43
4.3
43
430
4300
43000
430000
4300000
43000000
S
0.47
4.7
47
470
4700
47000
470000
4700000
47000000
T
0.51
5.1
51
510
5100
51000
510000
5100000
51000000
U
0.56
5.6
56
560
5600
56000
560000
5600000
56000000
V
0.62
6.2
62
620
6200
62000
620000
6200000
62000000
W
0.68
6.8
68
680
6800
68000
680000
6800000
68000000
X
0.75
7.5
75
750
7500
75000
750000
7500000
75000000
Y
0.82
8.2
82
820
8200
82000
820000
8200000
82000000
Z
0.91
9.1
91
910
9100
91000
910000
9100000
91000000
a
0.25
2.5
25
250
2500
25000
250000
2500000
25000000
b
0.35
3.5
35
350
3500
35000
350000
3500000
35000000
d
0.4
4
40
400
4000
40000
400000
4000000
40000000
e
0.45
4.5
45
450
4500
45000
450000
4500000
45000000
f
0.5
5
50
500
5000
50000
500000
5000000
50000000
m
0.6
6
60
600
6000
60000
600000
6000000
60000000
n
0.7
7
70
700
7000
70000
700000
7000000
70000000
t
0.8
8
80
800
8000
80000
800000
8000000
80000000
y
0.9
9
90
900
9000
90000
900000
9000000
90000000
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 6/11/2012 16
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) – X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
KEMET Corporation
World Headquarters
2835 KEMET Way
Simpsonville, SC 29681
Mailing Address:
P.O. Box 5928
Greenville, SC 29606
www.kemet.com
Tel: 864-963-6300
Fax: 864-963-6521
Corporate Of ces
Fort Lauderdale, FL
Tel: 954-766-2800
North America
Southeast
Lake Mary, FL
Tel: 407-855-8886
Northeast
Wilmington, MA
Tel: 978-658-1663
West Chester, PA
Tel: 610-692-4642
Central
Novi, MI
Tel: 248-994-1030
Carmel, IN
Tel: 317-706-6742
West
Milpitas, CA
Tel: 408-433-9950
Mexico
Zapopan, Jalisco
Tel: 52-33-3123-2141
Europe
Southern Europe
Geneva, Switzerland
Tel: 41-22-715-0100
Paris, France
Tel: 33-1-4646-1009
Sasso Marconi, Italy
Tel: 39 -051-939111
Milan, Italy
Tel: 39-02-57518176
Rome, Italy
Tel: 39-06-23231718
Madrid, Spain
Tel: 34-91-804-4303
Central Europe
Landsberg, Germany
Tel: 49-8191-3350800
Dortmund, Germany
Tel: 49-2307-3619672
Kwidzyn, Poland
Tel: 48-55-279-7025
Northern Europe
Bishop’s Stortford, United Kingdom
Tel: 44-1279-757201
Weymouth, United Kingdom
Tel: 44-1305-830747
Coatbridge, Scotland
Tel: 44-1236-434455
Färjestaden, Sweden
Tel: 46-485-563934
Espoo, Finland
Tel: 358-9-5406-5000
Asia
Northeast Asia
Hong Kong
Tel: 852-2305-1168
Shenzhen, China
Tel: 86-755-2518-1306
Beijing, China
Tel: 86-10-5829-1711
Shanghai, China
Tel: 86-21-6447-0707
Taipei, Taiwan
Tel: 886-2-27528585
Southeast Asia
Singapore
Tel: 65-6586-1900
Penang, Malaysia
Tel: 60-4-6430200
Bangalore, India
Tel: 91-806-53-76817
Note: KEMET reserves the right to modify minor details of internal and external construction at any time in the interest of product improvement. KEMET does not
assume any responsibility for infringement that might result from the use of KEMET Capacitors in potential circuit designs. KEMET is a registered trademark of
KEMET Electronics Corporation.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 6/11/2012 17
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) – X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
Other KEMET Resources
Tools
Resource Location
Con gure A Part: CapEdge http://capacitoredge.kemet.com
SPICE & FIT Software http://www.kemet.com/spice
Search Our FAQs: KnowledgeEdge http://www.kemet.com/keask
Product Information
Resource Location
Products http://www.kemet.com/products
Technical Resources (Including Soldering Techniques) http://www.kemet.com/technicalpapers
RoHS Statement http://www.kemet.com/rohs
Quality Documents http://www.kemet.com/qualitydocuments
Product Request
Resource Location
Sample Request http://www.kemet.com/sample
Engineering Kit Request http://www.kemet.com/kits
Contact
Resource Location
Website www.kemet.com
Contact Us http://www.kemet.com/contact
Investor Relations http://www.kemet.com/ir
Call Us 1-877-MyKEMET
Twitter http://twitter.com/kemetcapacitors
Disclaimer
All product speci cations, statements, information and data (collectively, the “Information”) are subject to change without notice.
All Information given herein is believed to be accurate and reliable, but is presented without guarantee, warranty, or responsibility of any kind, expressed or implied.
Statements of suitability for certain applications are based on our knowledge of typical operating conditions for such applications, but are not intended to constitute – and we
speci cally disclaim – any warranty concerning suitability for a speci c customer application or use. This Information is intended for use only by customers who have the requisite
experience and capability to determine the correct products for their application. Any technical advice inferred from this Information or otherwise provided by us with reference to the
use of our products is given gratis, and we assume no obligation or liability for the advice given or results obtained.
Although we design and manufacture our products to the most stringent quality and safety standards, given the current state of the art, isolated component failures may still occur.
Accordingly, customer applications which require a high degree of reliability or safety should employ suitable designs or other safeguards (such as installation of protective circuitry or
redundancies) in order to ensure that the failure of an electrical component does not result in a risk of personal injury or property damage.
Although all product-related warnings, cautions and notes must be observed, the customer should not assume that all safety measures are indicated or that other measures may not
be required.
© KEMET Electronics Corporation • P.O. Box 5928 • Greenville, SC 29606 (864) 963-6300 • www.kemet.com C1023_X7R_AUTO_SMD • 6/11/2012 18
Surface Mount Multilayer Ceramic Chip Capacitors (SMD MLCCs) – X7R Dielectric, 6.3 – 250 VDC (Automotive Grade)
Digitally signed by Marcy Brand
DN: c=US, st=FL, l=Fort Lauderdale, o=KEMET Corporation, ou=Marketing Communications, cn=Marcy Brand,
email=marcybrand@kemet.com
Date: 2012.06.13 16:48:53 -04'00'