3mm Single-Level Circuit Board Indicator Part Number: WP42WUM/EYW High Efficiency Red Yellow Features Descriptions z Pre-trimmed leads for pc mounting z The High Efficiency Red source color devices are made z Black case enhances contrast ratio with Gallium Arsenide Phosphide on Gallium Phosphide Orange Light Emitting Diode. z Wide viewing angle z High reliability-life measured in years z The Yellow source color devices are made with Gallium z Housing UL rating: 94V-0 Arsenide Phosphide on Gallium Phosphide Yellow Light z Housing material: Type 66 nylon Emitting Diode. z RoHS compliant Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is 0.25(0.01") unless otherwise noted. 3. Lead spacing is measured where the leads emerge from the package. 4. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. SPEC NO: DSAF1869 REV NO: V.7A DATE: MAY/24/2017 PAGE: 1 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1102005547 Selection Guide Part No. Emitting Color (Material) Lens Type Iv (mcd) [2] @ 20mA Viewing Angle [1] Min. Typ. 10 20 *4 *8 2 6 *2 *6 21/2 High Efficiency Red (GaAsP/GaP) WP42WUM/EYW 140 White Diffused Yellow (GaAsP/GaP) Notes: 1. 1 / 2 is the angle from optical centerline where the luminous intensity is 1 / 2 of the optical peak value. 2. Luminous intensity / luminous Flux: + / -15%. 3. Luminous intensity value is traceable to CIE127-2007 standards. Electrical / Optical Characteristics at TA=25C Symbol Parameter Emitting Color Typ. peak Peak Wavelength High Efficiency Red Yellow D [1] Dominant Wavelength 1/2 Max. Units Test Conditions 627 590 nm IF=20mA High Efficiency Red Yellow 617 588 nm IF=20mA Spectral Line Half-width High Efficiency Red Yellow 45 35 nm IF=20mA C Capacitance High Efficiency Red Yellow 15 20 pF VF=0V;f=1MHz VF [2] Forward Voltage High Efficiency Red Yellow 2 2.1 2.5 2.5 V IF=20mA IR Reverse Current High Efficiency Red Yellow 10 10 uA VR = 5V Notes: 1. Wavelength: + / -1nm. 2. Forward Voltage: + / -0.1V. 3. Wavelength value is traceable to CIE127-2007 standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25C Parameter High Efficiency Red Yellow Units Power dissipation 75 75 mW DC Forward Current 30 30 mA Peak Forward Current [1] 160 140 mA Reverse Voltage V 5 Operating / Storage Temperature -40C To +85C Lead Solder Temperature [2] 260C For 3 Seconds Lead Solder Temperature [3] 260C For 5 Seconds Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. 2mm below package base. 3. 5mm below package base. 4. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity - Ref JEDEC/JESD625-A and JEDEC/J-STD-033. SPEC NO: DSAF1869 REV NO: V.7A DATE: MAY/24/2017 PAGE: 2 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1102005547 Yellow Relative Intensity (a. u.) 100% 80% Red Ta = 25 C 60% 40% 20% 0% 350 400 450 500 550 600 Wavelength (nm) 650 700 750 800 WP42WUM/EYW High Efficiency Red -15 Ta = 25 C 0 -30 15 30 -45 45 60 -60 75 -75 -90 1.0 0.5 0.0 0.5 90 1.0 SPEC NO: DSAF1869 REV NO: V.7A DATE: MAY/24/2017 PAGE: 3 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1102005547 Yellow -15 Ta = 25 C 0 -30 15 30 -45 45 60 -60 75 -75 -90 1.0 0.5 0.0 0.5 90 1.0 SPEC NO: DSAF1869 REV NO: V.7A DATE: MAY/24/2017 PAGE: 4 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1102005547 PACKING & LABEL SPECIFICATIONS WP42WUM/EYW Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAF1869 REV NO: V.7A DATE: MAY/24/2017 PAGE: 5 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1102005547 SPEC NO: DSAF1869 REV NO: V.7A DATE: MAY/24/2017 PAGE: 6 OF 6 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.T.Zhang ERP: 1102005547 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Kingbright: WP42WUM/EYW