ADC10664CIWMXNOPB - TEXAS INSTRUMENTS

16-Bit, 1.5 LSB INL, 250 kSPS PulSAR

Differential ADC in MSOP

Data Sheet AD7687

Rev. E Document Feedback

Information furnished by Analog Devices is believed to be accurate and reliable. However, no

responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other

rights of third parties that may result from its use. Specifications subject to change without notice. No

license is granted by implication or otherwise under any patent or patent rights of Analog Devices.

Trademarks and registered trademarks are the property of their respective owners.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.

Technical Support www.analog.com

FEATURES

16-bit resolution with no missing codes

Throughput: 250 kSPS

INL: ±0.4 LSB typ, ±1.5 LSB max (±23 ppm of FSR)

Dynamic range: 96.5 dB

SNR: 95.5 dB at 20 kHz

THD: −118 dB at 20 kHz

True differential analog input range

±VREF

0 V to VREF with VREF up to VDD on both inputs

No pipeline delay

Single-supply 2.3 V to 5.5 V operation with

1.8 V/2.5 V/3 V/5 V logic interface

Proprietary serial interface: SPI/QSPI™/MICROWIRE/DSP

compatible

Daisy-chain multiple ADCs and BUSY indicator

Power dissipation

1.35 mW at 2.5 V/100 kSPS, 4 mW at 5 V/100 kSPS, and

1.4 μW at 2.5 V/100 SPS

Standby current: 1 nA

10-lead MSOP and 10-lead, 3 mm × 3 mm LFCSP

Pin-for-pin compatible with AD7685, AD7686, and AD7688

APPLICATIONS

Battery-powered equipment

Data acquisitions

Instrumentation

Medical instruments

Process controls

TYPICAL APPLICATION CIRCUIT

AD7687

REF

GND

VDD

IN+

IN–

VIO

SDI

SCK

SDO

CNV

1.8V TO VDD

3- OR 4-W I RE I NTERFACE

(SPI, DAISY CHAIN, CS )

0.5V TO 5V 2.5 TO 5V

VREF

02972-002

VREF

Figure 1.

GENERAL DESCRIPTION

The AD76871 is a 16-bit, charge redistribution, successive

approximation, analog-to-digital converter (ADC) that operates

from a single power supply, VDD, between 2.3 V to 5.5 V. It

contains a low power, high speed, 16-bit sampling ADC with no

missing codes, an internal conversion clock, and a versatile

serial interface port. The device also contains a low noise, wide

bandwidth, short aperture delay track-and-hold circuit. On the

CNV rising edge, the AD7687 the samples the voltage difference

between IN+ and IN− pins, which can range from −VREF to +VREF.

The reference voltage, VREF, is applied externally and can be set

up to the supply voltage.

The power consumption of the device scales linearly with

throughput.

The SPI-compatible serial interface also features the ability to

daisy-chain several ADCs on a single 3-wire bus and provides

an optional BUSY indicator by means of the SDI pin. It is

compatible with 1.8 V, 2.5 V, 3 V, or 5 V logic using the separate

supply VIO.

The AD7687 comes in a 10-lead MSOP or a 10-lead LFCSP

with operation specified from −40°C to +85°C.

Table 1. MSOP, LFCSP/SOT-23 16-Bit PulSAR® ADC

Type 100 kSPS 250 kSPS 500 kSPS

True Differential AD7684 AD7687 AD7688

Pseudo AD7683 AD7685 AD7686

Differential/Unipolar AD7694

Unipolar AD7680

1 Protected by U.S. Patent 6,703,961.

AD7687* PRODUCT PAGE QUICK LINKS

Last Content Update: 02/23/2017

COMPARABLE PARTS

View a parametric search of comparable parts.

EVALUATION KITS

•AD7687 Evaluation Kit

•Precision ADC PMOD Compatible Boards

DOCUMENTATION

Application Notes

•AN-931: Understanding PulSAR ADC Support Circuitry

•AN-932: Power Supply Sequencing

Data Sheet

•AD7687: 16-Bit, 1.5 LSB INL, 250 kSPS PulSAR Differential

ADC in MSOP Data Sheet

Product Highlight

•[NO TITLE FOUND] Product Highlight

•8- to 18-Bit SAR ADCs ... From the Leader in High

Performance Analog

•Lowest-Power 16-Bit ADC Optimizes Portable Designs

(eeProductCenter, 10/4/2006)

User Guides

•UG-340: Evaluation Board for the 10-Lead Family 14-/16-/

18-Bit PulSAR ADCs

•UG-682: 6-Lead SOT-23 ADC Driver for the 8-/10-Lead

Family of 14-/16-/18-Bit PulSAR ADC Evaluation Boards

SOFTWARE AND SYSTEMS REQUIREMENTS

•AD7687 FMC-SDP Interposer & Evaluation Board / Xilinx

KC705 Reference Design

•BeMicro FPGA Project for AD7687 with Nios driver

TOOLS AND SIMULATIONS

•AD7685 IBIS Models

REFERENCE DESIGNS

•CN0225

REFERENCE MATERIALS

Technical Articles

•MS-1779: Nine Often Overlooked ADC Specifications

•MS-2210: Designing Power Supplies for High Speed ADC

Tutorials

•MT-074: Differential Drivers for Precision ADCs

DESIGN RESOURCES

•AD7687 Material Declaration

•PCN-PDN Information

•Quality And Reliability

•Symbols and Footprints

DISCUSSIONS

View all AD7687 EngineerZone Discussions.

SAMPLE AND BUY

Visit the product page to see pricing options.

TECHNICAL SUPPORT

Submit a technical question or find your regional support

number.

DOCUMENT FEEDBACK

Submit feedback for this data sheet.

This page is dynamically generated by Analog Devices, Inc., and inserted into this data sheet. A dynamic change to the content on this page will not

trigger a change to either the revision number or the content of the product data sheet. This dynamic page may be frequently modified.

AD7687 Data Sheet

Rev. E | Page 2 of 26

TABLE OF CONTENTS

Features .............................................................................................. 1

Applications ....................................................................................... 1

Typical Application Circuit ............................................................. 1

General Description ......................................................................... 1

Revision History ............................................................................... 3

Specifications ..................................................................................... 4

Timing Specifications .................................................................. 6

Absolute Maximum Ratings ............................................................ 8

Thermal Resistance ...................................................................... 8

ESD Caution .................................................................................. 8

Pin Configurations and Function Descriptions ........................... 9

Terminology .................................................................................... 10

Typical Performance Characteristics ........................................... 11

Theory of Operation ...................................................................... 14

Circuit Information .................................................................... 14

Converter Operation .................................................................. 14

Typical Connection Diagram ................................................... 15

Analog Input ............................................................................... 16

Driver Amplifier Choice ........................................................... 17

Single-to-Differential Driver .................................................... 17

Voltage Reference Input ............................................................ 17

Power Supply ............................................................................... 17

Supplying the ADC from the Reference .................................. 18

Digital Interface .......................................................................... 18

CS Mode, 3-Wire Without BUSY Indicator ........................... 19

CS Mode, 3-Wire with BUSY Indicator .................................. 20

CS Mode, 4-Wire Without BUSY Indicator ........................... 21

CS Mode, 4-Wire with BUSY Indicator .................................. 22

Chain Mode Without BUSY Indicator .................................... 23

Chain Mode with BUSY Indicator ........................................... 24

Applications Information .............................................................. 25

Layout .......................................................................................... 25

Evaluating the Performance of the AD7687 ............................... 25

Outline Dimensions ....................................................................... 26

Ordering Guide .......................................................................... 26

Data Sheet AD7687

Rev. E | Page 3 of 26

REVISION HISTORY

12/15—Rev. D to Rev. E

Deleted Figure 1; Renumbered Sequentially ................................. 1

Changes to Features Section and General Description Section ....... 1

Change to Signal-to-(Noise + Distortion) Parameter, Table 2 ......... 4

Added Timing Diagrams Section .................................................... 7

Moved Figure 2 and Figure 3 ........................................................... 7

Changes to Table 8 ............................................................................ 9

Changes to Figure 7 Caption, Figure 8 Caption, Figure 10

Caption, and Figure 11 Caption .................................................... 11

Added Theory of Operation Section ............................................ 14

Changes to Analog Input Section ................................................. 16

Changes to Drive Amplifier Choice Section, Table 10, Figure 30,

Voltage Reference Input Section, and Power Supply Section ......... 17

Changes to Supplying the ADC from the Reference Section

and Digital Interface Section ......................................................... 18

Changed CS Mode, 3-Wire, No BUSY Indicator Section to CS

Mode, 3-Wire Without BUSY Indicator Section ........................ 19

Changes to CS Mode, 3-Wire Without BUSY Indicator Section ... 19

Changes to CS Mode, 3-Wire with BUSY Indicator Section ...... 20

Changed CS Mode, 4-Wire, No BUSY Indicator Section to CS

Mode, 4-Wire Without BUSY Indicator Section ........................ 21

Changes to CS Mode, 4-Wire Without BUSY Indicator Section ... 21

Changes to CS Mode, 4-Wire with BUSY Indicator Section .......... 22

Changed Chain Mode, No BUSY Indicator Section to Chain

Mode Without BUSY Indicator Section ....................................... 23

Changes to Chain Mode Without BUSY Indicator Section,

Figure 42 Caption, and Figure 43 Caption ................................... 23

Changes to Chain Mode with BUSY Indicator Section ............. 24

Changes to Layout Section ............................................................. 25

Changed Application Hints Section to Application

Recommendations Section ............................................................ 25

Changes to Ordering Guide ........................................................... 26

4/15—Rev. C to Rev. D

Added Patent Note, Note 1 .............................................................. 1

Changes to SNR Degradation Equation, Driver Amplifier

Choice Section ................................................................................. 16

Changes to Ordering Guide ........................................................... 26

7/14—Rev. B to Rev. C

Deleted QFN ................................................................... Throughout

Changed Application Diagram Section to Typical Application

Circuit Section ................................................................................... 1

Change to Features Section .............................................................. 1

Added Note 1 ..................................................................................... 1

Changes to Figure 27 ...................................................................... 14

Changes to Evaluating the Performance of the AD7687

Section .............................................................................................. 24

Updated Outline Dimensions ........................................................ 25

Changes to Ordering Guide ........................................................... 26

8/11—Rev. A to Rev. B

Changes to Table 7 ............................................................................ 7

Changes to Ordering Guide ........................................................... 26

2/11—Rev. 0 to Rev. A

Deleted QFN in Development Note ............................ Throughout

Changes to Table 6 ............................................................................ 7

Added Thermal Resistance Section and Table 7 ........................... 7

Changes to Figure 6 and Table 8 ..................................................... 8

Updated Outline Dimensions ........................................................ 25

Changes to Ordering Guide ........................................................... 26

4/05—Revision 0: Initial Version

AD7687 Data Sheet

Rev. E | Page 4 of 26

SPECIFICATIONS

VDD = 2.3 V to 5.5 V, VIO = 2.3 V to VDD, VREF = VDD, TA = −40°C to +85°C, unless otherwise noted.

Table 2.

Parameter Test Conditions/Comments Min Typ Max Unit

RESOLUTION 16 Bits

ANALOG INPUT

Voltage Range IN+ − IN− −VREF +VREF V

Absolute Input Voltage

IN+ and IN−

−0.1

REF

+ 0.1

Common-Mode Input Range IN+ and IN− 0 VREF/2 VREF/2 + 0.1 V

Analog Input CMRR fIN = 250 kHz 65 dB

Leakage Current at 25°C Acquisition phase 1 nA

Input Impedance See the Analog Input section

ACCURACY

No Missing Codes 16 Bits

Differential Linearity Error −1 ±0.4 +1 LSB1

Integral Linearity Error −1.5 ±0.4 +1.5 LSB

Transition Noise

REF = VDD = 5 V

0.35

LSB

Gain Error2, TMIN to TMAX ±2 ±6 LSB

Gain Error Temperature Drift ±0.3 ppm/°C

Offset Error2, TMIN to TMAX VDD = 4.5 V to 5.5 V ±0.1 ±1.6 mV

VDD = 2.3 V to 4.5 V ±0.7 ±3.5 mV

Offset Temperature Drift

±0.3

ppm/°C

Power Supply Sensitivity VDD = 5 V ± 5% ±0.05 LSB

THROUGHPUT

Conversion Rate VDD = 4.5 V to 5.5 V 0 250 kSPS

VDD = 2.3 V to 4.5 V 0 200 kSPS

Transient Response Full-scale step 1.8 µs

AC ACCURACY

Dynamic Range VREF = 5 V 95.8 96.5 dB3

Signal-to-Noise Ratio fIN = 20 kHz, VREF = 5 V 94 95.5 dB

fIN = 20 kHz, VREF = 2.5 V 92 92.5 dB

Spurious-Free Dynamic Range fIN = 20 kHz −118 dB

Total Harmonic Distortion

= 20 kHz

−118

Signal-to-(Noise + Distortion) Ratio fIN = 20 kHz, VREF = 5 V 94 95 dB

fIN = 20 kHz, VREF = 5 V, −60 dB input 36.5 dB

fIN = 20 kHz, VREF = 2.5 V 92 92.5 dB

Intermodulation Distortion4 115 dB

1 LSB means least significant bit. With the ±5 V input range, one LSB is 152.6 µV.

2 See the Terminology section. These specifications do include full temperature range variation but do not include the error contribution from the external reference.

3 All specifications in dB are referred to a full-scale input FSR. Tested with an input signal at 0.5 dB below full-scale, unless otherwise specified.

4 fIN1 = 21.4 kHz, fIN2 = 18.9 kHz, each tone at −7 dB below full-scale.

Data Sheet AD7687

Rev. E | Page 5 of 26

VDD = 2.3 V to 5.5 V, VIO = 2.3 V to VDD, VREF = VDD, TA = −40°C to +85°C, unless otherwise noted.

Table 3.

Parameter Test Conditions/Comments Min Typ Max Unit

REFERENCE

Voltage Range 0.5 VDD + 0.3 V

Load Current 250 kSPS, REF = 5 V 50 µA

SAMPLING DYNAMICS

−3 dB Input Bandwidth 2 MHz

Aperture Delay VDD = 5 V 2.5 ns

DIGITAL INPUTS

Logic Levels

VIL −0.3 +0.3 × VIO V

VIH 0.7 × VIO VIO + 0.3 V

IIL −1 +1 µA

IIH −1 +1 µA

DIGITAL OUTPUTS

Data Format Serial 16-bits twos complement

Pipeline Delay Conversion results available immediately

after completed conversion

VOL ISINK = 500 µA 0.4 V

SOURCE

= −500 µA

VIO − 0.3

POWER SUPPLIES

VDD Specified performance 2.3 5.5 V

VIO

Specified performance

2.3

VDD + 0.3

VIO Range 1.8 VDD + 0.3 V

Standby Current1, 2 VDD and VIO = 5 V, 25°C 1 50 nA

Power Dissipation VDD = 2.5 V, 100 SPS throughput 1.4 µW

VDD = 2.5 V, 100 kSPS throughput 1.35 mW

VDD = 2.5 V, 200 kSPS throughput

2.7

VDD = 5 V, 100 kSPS throughput 4 5.5 mW

VDD = 5 V, 250 kSPS throughput 12.5 mW

TEMPERATURE RANGE3

Specified Performance TMIN to TMAX −40 +85 °C

1 With all digital inputs forced to VIO or GND as required.

2 During acquisition phase.

3 Contact sales for extended temperature range.

AD7687 Data Sheet

Rev. E | Page 6 of 26

TIMING SPECIFICATIONS

−40°C to +85°C, VDD = 4.5 V to 5.5 V, VIO = 2.3 V to 5.5 V or VDD + 0.3 V, whichever is the lowest, unless otherwise stated.

See Figure 2 and Figure 3 for load conditions.

Table 4.

Parameter Symbol Min Typ Max Unit

CONVERSION TIME: CNV RISING EDGE TO DATA AVAILABLE tCONV 0.5 2.2 µs

ACQUISITION TIME tACQ 1.8 µs

TIME BETWEEN CONVERSIONS tCYC 4 µs

CNV PULSE WIDTH (CS MODE) tCNVH 10 ns

SCK PERIOD tSCK

CS Mode 15 ns

Chain Mode

VIO Above 4.5 V 17 ns

VIO Above 3 V 18 ns

VIO Above 2.7 V 19 ns

VIO Above 2.3 V

SCK TIME

Low tSCKL 7 ns

High

SCKH

SCK FALLING EDGE

To Data Remains Valid tHSDO 5

To Data Valid Delay tDSDO

VIO Above 4.5 V 14 ns

VIO Above 3 V 15 ns

VIO Above 2.7 V 16 ns

VIO Above 2.3 V 17 ns

CNV OR SDI

Low to SDO D15 MSB Valid (CS Mode) tEN

VIO Above 4.5 V 15 ns

VIO Above 2.7 V

VIO Above 2.3 V 22 ns

High or Last SCK Falling Edge to SDO High Impedance (CS Mode) tDIS 25 ns

SDI

Valid Setup Time from CNV Rising Edge (CS Mode) tSSDICNV 15 ns

Valid Hold Time from CNV Rising Edge (CS Mode) tHSDICNV 0 ns

Valid Setup Time from SCK Falling Edge (Chain Mode) tSSDISCK 3 ns

Valid Hold Time from SCK Falling Edge (Chain Mode) tHSDISCK 4 ns

High to SDO High (Chain Mode with BUSY indicator) tDSDOSDI

VIO Above 4.5 V 15 ns

VIO Above 2.3 V 26 ns

SCK

Valid Setup Time from CNV Rising Edge (Chain Mode) tSSCKCNV 5 ns

Valid Hold Time from CNV Rising Edge (Chain Mode) tHSCKCNV 5 ns

Data Sheet AD7687

Rev. E | Page 7 of 26

−40°C to +85°C, VDD = 2.3 V to 4.5 V, VIO = 2.3 V to 4.5 V or VDD + 0.3 V, whichever is the lowest, unless otherwise stated.

See Figure 2 and Figure 3 for load conditions.

Table 5.

Parameter Symbol Min Typ Max Unit

CONVERSION TIME: CNV RISING EDGE TO DATA AVAILABLE tCONV 0.7 3.2 µs

ACQUISITION TIME tACQ 1.8 µs

TIME BETWEEN CONVERSIONS

CYC

µs

CNV PULSE WIDTH (CS MODE) tCNVH 10 ns

SCK PERIOD tSCK

CS Mode 25 ns

Chain Mode

VIO Above 3 V 29 ns

VIO Above 2.7 V

VIO Above 2.3 V 40 ns

SCK TIME

Low tSCKL 12 ns

High tSCKH 12 ns

SCK FALLING EDGE

To Data Remains Valid tHSDO 5

To Data Valid Delay tDSDO

VIO Above 3 V 24 ns

VIO Above 2.7 V 30 ns

VIO Above 2.3 V 35 ns

CNV OR SDI

Low to SDO D15 MSB Valid (CS Mode) tEN

VIO Above 2.7 V 18 ns

VIO Above 2.3 V

High or Last SCK Falling Edge to SDO High Impedance (CS Mode) tDIS 25 ns

SDI

Valid Setup Time from CNV Rising Edge (CS Mode) tSSDICNV 30 ns

Valid Hold Time from CNV Rising Edge (CS Mode) tHSDICNV 0 ns

Valid Setup Time from SCK Falling Edge (Chain Mode) tSSDISCK 5 ns

Valid Hold Time from SCK Falling Edge (Chain Mode) tHSDISCK 4 ns

High to SDO High (Chain Mode with BUSY indicator) tDSDOSDI 36 ns

SCK

Valid Setup Time from CNV Rising Edge (Chain Mode) tSSCKCNV 5 ns

Valid Hold Time from CNV Rising Edge (Chain Mode) tHSCKCNV 8 ns

Timing Diagrams

500µA I

1.4V

TO SDO C

50pF

02972-003

Figure 2. Load Circuit for Digital Interface Timing

30% VIO 70% VIO

2V OR VIO – 0.5V

0.8V OR 0.5V

2V OR VIO – 0.5V

tDELAY tDELAY

02972-004

2V IF VIO ABOVE 2.5V, VIO– 0.5V IF VIO BELOW 2.5V.

0.8V IF VIO ABOVE 2.5V, 0.5V IF VIO BELOW 2.5V.

Figure 3. Voltage Levels for Timing

AD7687 Data Sheet

Rev. E | Page 8 of 26

ABSOLUTE MAXIMUM RATINGS

Table 6.

Parameter Rating

Analog Inputs

IN+1, IN−1 GND − 0.3 V to VDD + 0.3 V

or ±130 mA

REF GND − 0.3 V to VDD + 0.3 V

Supply Voltages

VDD, VIO to GND −0.3 V to +7 V

VDD to VIO ±7 V

Digital Inputs to GND

−0.3 V to VIO + 0.3 V

Digital Outputs to GND −0.3 V to VIO + 0.3 V

Storage Temperature Range −65°C to +150°C

Junction Temperature 150°C

Lead Temperature Range JEDEC J-STD-20

1 See the Analog Input section.

Stresses at or above those listed under Absolute Maximum

Ratings may cause permanent damage to the product. This is a

stress rating only; functional operation of the product at these

or any other conditions above those indicated in the operational

section of this specification is not implied. Operation beyond

the maximum operating conditions for extended periods may

affect product reliability.

THERMAL RESISTANCE

θJA is specified for the worst-case conditions, that is, a device

soldered in a circuit board for surface-mount packages.

Table 7. Thermal Resistance

Package Type θJA θJC Unit

10-Lead LFCSP 84 2.96 °C/W

10-Lead MSOP 200 44 °C/W

ESD CAUTION

Data Sheet AD7687

Rev. E | Page 9 of 26

PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS

02972-005

REF 1

VDD 2

IN+ 3

IN– 4

GND 5

VIO10

SDI9

SCK8

SDO

CNV

AD7687

TOP VIEW

(Not to Scale)

Figure 4. 10-Lead MSOP Pin Configuration

02972-006

1REF

2VDD

3IN+

4IN–

5GND

10 VIO

9SDI

8SCK

7SDO

6 CNV

NOTES

1. FOR THE LFCSP ONLY, THE EXPOSED

PADDLE MUST BE CONNECT E D TO GND.

TOP VI EW

(Not to Scale)

AD7687

Figure 5. 10-Lead LFCSP Pin Configuration

Table 8. Pin Function Descriptions

Pin No. Mnemonic Type1 Function

1 REF AI

Reference Input Voltage. The REF range is from 0.5 V to VDD, referred to the GND pin. Place a 10 μF

decoupling capacitor as close to the pin as possible.

2 VDD P Power Supply.

3 IN+ AI Differential Positive Analog Input.

4 IN− AI Differential Negative Analog Input.

5 GND P Power Supply Ground.

6 CNV DI

Convert Input. This input has multiple functions. On its leading edge, it initiates a conversion and selects

the interface mode: chain or CS (depending on the state of SDI). In CS mode, CNV enables the SDO pin

when low. In chain mode, the data is read while CNV is high.

7 SDO DO

Serial Data Output. The conversion result is output on this pin. It is synchronized to SCK. SDO also acts as

the BUSY indicator if the feature is enabled.

8 SCK DI

Serial Data Clock Input. This input primarily shifts data out on SDO when data is valid. In chain mode, the

state of SCK determines if the BUSY indicator feature is enabled. If SCK is low during the CNV rising edge,

the BUSY feature is disabled. If it is high during the CNV rising edge, the BUSY feature is enabled.

9 SDI DI Serial Data Input. This input serves multiple functions. It selects the interface mode of the ADC as follows:

Chain mode is selected if SDI is low during the CNV rising edge. In this mode, SDI is used as a data input to

daisy chain the conversion results of two or more ADCs onto a single SDO line. The digital data level on SDI

is output on SDO with a delay of 16 SCK cycles.

CS mode is selected if SDI is high during the CNV rising edge. In this mode, either SDI or CNV can enable

the serial output signals when low, and if SDI or CNV is low when the conversion is complete, the BUSY

indicator feature is enabled.

10 VIO P

Input/Output Interface Digital Power. Nominally at the same supply as the host interface (1.8 V, 2.5 V, 3 V,

or 5 V).

EPAD N/A For the LFCSP only, the exposed paddle must be connected to GND.

1AI means analog input, DI means digital input, DO means digital output, P means power, and N/A means not applicable.

AD7687 Data Sheet

Rev. E | Page 10 of 26

TERMINOLOGY

Integral Nonlinearity Error (INL)

INL refers to the deviation of each individual code from a line

drawn from negative full scale through positive full scale. The

point used as negative full scale occurs ½ LSB before the first

code transition. Positive full scale is defined as a level 1½ LSB

beyond the last code transition. Measure the deviation from the

middle of each code to the true straight line (see Figure 25).

Differential Nonlinearity Error (DNL)

In an ideal ADC, code transitions are 1 LSB apart. The DNL is

the maximum deviation from this ideal value. It is often specified

in terms of resolution for which no missing codes are guaranteed.

Zero Error

Zero error is the difference between the ideal midscale voltage,

that is, 0 V, from the actual voltage producing the midscale

output code, that is, 0 LSB.

Gain Error

The first transition (from 100…00 to 100…01) should occur at

a level ½ LSB above nominal negative full scale (−4.999924 V

for the ±5 V range). The last transition (from 011…10 to

011…11) should occur for an analog voltage 1½ LSB below the

nominal full scale (+4.999771 V for the ±5 V range.) The gain

error is the deviation of the difference between the actual level

of the last transition and the actual level of the first transition

from the difference between the ideal levels.

Spurious-Free Dynamic Range (SFDR)

SFDR is the difference, in decibels (dB), between the rms

amplitude of the input signal and the peak spurious signal.

Effective Number of Bits (ENOB)

ENOB is a measurement of the resolution with a sine wave

input. It is related to SINAD by the following formula

ENOB = (SINADdB − 1.76)/6.02

and is expressed in bits.

Total Harmonic Distortion (THD)

THD is the ratio of the rms sum of the first five harmonic

components to the rms value of a full-scale input signal and is

expressed in dB.

Dynamic Range

Dynamic range is the ratio of the rms value of the full scale to

the total rms noise measured with the inputs shorted together.

The value for dynamic range is expressed in dB.

Signal-to-Noise Ratio (SNR)

SNR is the ratio of the rms value of the actual input signal to the

rms sum of all other spectral components below the Nyquist

frequency, excluding harmonics and dc. The value for SNR is

expressed in dB.

Signal-to-(Noise + Distortion) Ratio (SINAD)

SINAD is the ratio of the rms value of the actual input signal to

the rms sum of all other spectral components below the Nyquist

frequency, including harmonics but excluding dc. The value for

SINAD is expressed in dB.

Aperture Delay

Aperture delay is the measure of the acquisition performance. It

is the time between the rising edge of the CNV input and when

the input signal is held for a conversion.

Transient Response

Transient response is the time required for the ADC to acquire its

input accurately after a full-scale step function is applied.

Data Sheet AD7687

Rev. E | Page 11 of 26

TYPICAL PERFORMANCE CHARACTERISTICS

CODE

INL (LSB)

1.5

1.0

0.5

–0.5

–1.0

–1.5 0 16384 32768 49152 65535

02972-001

POSITIVE INL = +0.32LSB

NEGATIVE INL = –0.41LSB

Figure 6. Integral Nonlinearity vs. Code

02972-007

COUNTS

300000

250000

150000

200000

100000

50000

CODE IN HEX 45 46 47

41 42 43 44

0 0 1049 0 0

258680

1391

VDD = REF = 5V

Figure 7. Histogram of a DC Input at the Code Center, VDD = REF = 5 V

FRE Q UE NCY ( kHz )

AMPLITUDE (dB of Full Scale)

–20

–40

–60

–80

–100

–120

–160

–140

–180 020 40 60 80 100 120

02972-008

8192 POINT FFT

VDD = REF = 5V

= 250kSPS

= 2.1kHz

SNR = 95. 5dB

THD = – 118.3dB

2nd HARMO NIC = –130d B

3rd HARM ONIC = –122.7dB

Figure 8. FFT Plot, VDD = REF = 5 V

CODE

DNL (LSB)

1.5

1.0

0.5

–0.5

–1.0

–1.5 0 16384 32768 49152 65535

02972-009

POSITIVE DNL = +0.27LSB

NEGATIVE DNL = –0.24LSB

Figure 9. Differential Nonlinearity vs. Code

02972-010

COUNTS

250000

150000

200000

100000

50000

CODE IN HEX

49 4A 4C44 46 47 48

060

30721

0 0

200403

29918

VDD = REF = 2.5V

Figure 10. Histogram of a DC Input at the Code Center, VDD = REF = 2.5 V

FRE Q UE NCY ( kHz )

AMPLITUDE (dB of Full Scale)

–20

–40

–60

–80

–100

–120

–160

–140

–180 020 40 60 80 100 120

02972-011

32768 POINT FFT

VDD = REF = 2.5V

= 250kSPS

= 2kHz

SNR = 92. 8dB

THD = –115.9d B

2nd HARMO NIC = –124d B

3rd HARM ONIC = –119dB

Figure 11. FFT Plot, VDD = REF = 2.5 V

AD7687 Data Sheet

Rev. E | Page 12 of 26

02972-012

REFERENCE VOLTAGE (V) 5.52.3 2.7 3.5 4.3 5.13.1 3.9 4.7

SNR, S INAD (dB)

100

SNR

ENOB

ENOB (Bit s)

17.0

15.0

16.0

14.0

13.0

SINAD

Figure 12. SNR, SINAD, and ENOB vs. Reference Voltage

02972-013

FRE Q UE NCY ( kHz ) 200050 100 150

SINAD (dB)

100

VREF = 5V, –10dB

VREF = 2.5V, –10d B

VREF = 2.5V, –1d B

VREF = 5V, –1dB

Figure 13. SINAD vs. Frequency

02972-014

TEMPERATURE (°C) 125–55 –35 –15 5 25 45 65 85 105

SNR (dB)

100

VREF = 5V

VREF = 2.5V

Figure 14. SNR vs. Temperature

02972-015

REFERENCE VOLTAGE (V) 5.52.3 2.7 3.5 4.3 5.13.1 3.9 4.7

THD, SFDR (dB)

–100

–105

–110

–115

–120

–125

–130

THD

SFDR

Figure 15. THD, SFDR vs. Reference Voltage

02972-016

FREQUENCY (kHz) 2000 50 100 150

THD (dB)

–60

–70

–90

–80

–100

–110

–120

VREF = 5V,–10dB

VREF = 2.5V,–10dB

VREF = 5V,–1dB

VREF = 2.5V,–1dB

Figure 16. THD vs. Frequency

02972-017

TEMPERATURE (°C) 125–55 –35 –15 5 25 45 65 85 105

THD (dB)

–90

–100

–110

–120

–130

VREF = 5V

VREF = 2.5V

Figure 17. THD vs. Temperature

Data Sheet AD7687

Rev. E | Page 13 of 26

02972-018

INPUT LEVEL (dB) 0–10 –8 –6 –4 –2

SNR (dB)

100

VREF = 5V

VREF = 2.5V

Figure 18. SNR vs. Input Level

SUPPLY (V)

OPERATING CURRENT (µA)

1000

750

500

250

02.3 3.1 3.9 4.7 5.52.7 3.5 4.3 5.1

02972-019

VIO

VDD

= 100kSPS

Figure 19. Operating Current vs. Supply

TEMPERATURE (°C)

POWER-DOWN CURRENT (nA)

1000

750

500

250

–55 –35 –15 5 25 45 65 85 105 125

02972-020

VDD + VIO

Figure 20. Power-Down Current vs. Temperature

TEMPERATURE (°C)

OPERATING CURRENT (µA)

1000

750

500

250

–55 –35 –15 5 25 45 65 85 105 125

02972-021

VIO

VDD = 5V

VDD = 2.5V

= 100kSPS

Figure 21. Operating Current vs. Temperature

02972-022

TEMPERATURE (°C) 125–55 –35 –15 525 45 65 85 105

OFFS E T ERRO R AND GAIN E RROR (LSB)

–2

–4

–6

GAI N E RROR

OFFSET ERROR

Figure 22. Offset Error and Gain Error vs. Temperature

02972-023

SDO CAPACITIVE LOAD (pF) 120020 40 60 80 100

DSDO

DEL AY (ns)

VDD = 2. 5V , 85° C

VDD = 3. 3V , 25° C

VDD = 3. 3V , 85° C

VDD = 5V, 85° C

VDD = 5V, 25° C

VDD = 2. 5V , 25° C

Figure 23. tDSDO Delay vs. Capacitance Load and Supply

AD7687 Data Sheet

Rev. E | Page 14 of 26

THEORY OF OPERATION

SW+MSB

16,384C

IN+

LSB

COMP CONTROL

LOGIC

SWITCHES CONTROL

BUSY

OUTPUT CODE

CNV

REF

GND

IN–

4C 2C C C32,768C

SW–MSB

16,384C

LSB

4C 2C C C32,768C

02972-024

Figure 24. ADC Simplified Schematic

CIRCUIT INFORMATION

The AD7687 is a fast, low power, single-supply, precise 16-bit

ADC using a successive approximation architecture.

The AD7687 is capable of converting 250,000 samples per

second (250 kSPS) and powers down between conversions.

When operating at 100 SPS, for example, it typically consumes

1.35 µW, which is ideal for battery-powered applications.

The AD7687 provides the user with an on-chip track-and-hold

and does not exhibit any pipeline delay or latency, making it

ideal for multiple multiplexed channel applications.

The AD7687 is specified for use from 2.3 V to 5.5 V and can be

interfaced to any of the 1.8 V to 5 V digital logic family. It is

housed in a 10-lead MSOP or in a tiny 10-lead LFCSP that saves

space and allows flexible configurations.

It is pin-for-pin-compatible with the AD7685, AD7686, and

AD7688.

CONVERTER OPERATION

The AD7687 is a successive approximation ADC based on a

charge redistribution DAC. Figure 24 shows the simplified

schematic of the ADC. The capacitive DAC consists of two

identical arrays of 16 binary weighted capacitors, which are

connected to the two comparator inputs.

During the acquisition phase, terminals of the array tied to the

input of the comparator are connected to GND via SW+ and

SW−. All independent switches are connected to the analog

inputs. Thus, the capacitor arrays function as sampling

capacitors and acquire the analog signal on the IN+ and IN−

inputs. When the acquisition phase is complete and the CNV

input goes high, a conversion phase is initiated. When the

conversion phase begins, SW+ and SW− open first. The two

capacitor arrays are then disconnected from the inputs and

connected to the GND input. Therefore, the differential voltage

between the inputs IN+ and IN− captured at the end of the

acquisition phase is applied to the comparator inputs, causing

the comparator to become unbalanced. By switching each

element of the capacitor array between GND and REF, the

comparator input varies by binary weighted voltage steps

(VREF/2, VREF/4…VREF/65536). The control logic toggles these

switches, starting with the MSB, to bring the comparator back

into a balanced condition. After the completion of this process,

the device returns to the acquisition phase and the control logic

generates the ADC output code and a BUSY signal indicator.

Because the AD7687 has an on-board conversion clock, the

serial clock, SCK, is not required for the conversion process.

Data Sheet AD7687

Rev. E | Page 15 of 26

Transfer Functions

Figure 25 and Table 9 show the ideal transfer characteristic for

the AD7687.

100...000

100...001

100...010

011...101

011...110

011...111

ADC CODE (TWOS COMPLEMENT)

ANALOG INPUT

+FSR – 1.5 LSB

FSR – 1 LSB

–FSR + 1 LSB

–FSR

–FSR + 0.5 LSB

02972-025

Figure 25. ADC Ideal Transfer Function

Table 9. Output Codes and Ideal Input Voltages

Description

Analog Input

VREF = 5 V

Digital Output Code

Hexadecimal

FSR − 1 LSB +4.999847 V 7FFF1

Midscale + 1 LSB +152.6 µV 0001

Midscale

0 V

0000

Midscale − 1 LSB −152.6 µV FFFF

−FSR + 1 LSB −4.999847 V 8001

−FSR −5 V 80002

1 This is also the code for an overranged analog input (VIN+ − VIN− above

VREF − VGND).

2 This is also the code for an underranged analog input (VIN+ − VIN− below

−VREF + VGND).

TYPICAL CONNECTION DIAGRAM

Figure 26 shows an example of the recommended connection

diagram for the AD7687 when multiple supplies are available.

AD7687

REF

GND

VDD

IN–

IN+ VIOSDI

SCK

SDO

CNV

3- O R 4- WIRE INTE RFACE

100nF

100nF 5V

10µF

≥7V

≤–2V

1.8V TO V DD

REF

0 TO VREF

33Ω

2.7nF

≥7V

≤–2V

VREF TO 0

33Ω

2.7nF

02972-026

SEE VOLTAGE I NP UT REF E RE NCE S E CTION F OR REF E RE NCE S E LECT ION.

REF

IS US UALLY A 10µF CERAMIC CA PACITOR (X 5R) .

SEE DRIVER AMPLIFIER CHOICE SECTION.

OPTIONAL FILTER. SEE ANALOG INPUT SECTION.

SEE DIGITAL INTERFACE FOR MOST CONVENIENT INTERFACE MODE.

Figure 26. Typical Connection Diagram with Multiple Supplies

AD7687 Data Sheet

Rev. E | Page 16 of 26

ANALOG INPUT

Figure 27 shows an equivalent circuit of the input structure of

the AD7687.

The two diodes, D1 and D2, provide ESD protection for the

analog inputs IN+ and IN−. Take care to ensure that the analog

input signal never exceeds the supply rails by more than 0.3 V

because this causes these diodes to begin to forward-bias and

start conducting current. These diodes can handle a forward-

biased current of 130 mA maximum. These overvoltage

conditions can occur if the supplies of the input buffer (U1)

differ from VDD. In such a case, use an input buffer with a

short-circuit current limitation to protect the device.

IN+

OR IN–

GND

VDD

02972-027

Figure 27. Equivalent Analog Input Circuit

The analog input structure allows the sampling of the true

differential signal between IN+ and IN−. This differential input

scheme allows for rejection of common-mode signals. Figure 28

shows the typical CMRR over frequency.

FREQUENCY (kHz)

CMRR (dB)

1 10 100 1000

02972-028

VDD = 5V

VDD = 2.5V

Figure 28. Analog Input CMRR vs. Frequency

During the acquisition phase, the impedance of the analog

inputs (IN+ or IN−) can be modeled as a parallel combination

of capacitor, CPIN, and the network formed by the series connection

of RIN and CIN. CPIN is primarily the pin capacitance. RIN is

typically 3 kΩ and is a lumped component made up of some

serial resistors and the on resistance of the switches. CIN is

typically 30 pF and is mainly the ADC sampling capacitor.

During the conversion phase, where the switches are opened,

the input impedance is limited to CPIN. RIN and CIN make a

1-pole, low-pass filter that reduces undesirable aliasing effects

and limits the noise.

If the source impedance of the driving circuit is sufficiently low,

the AD7687 can be driven directly. Large source impedances

significantly affect the ac performance, especially the total

harmonic distortion (THD). The maximum source impedance

depends on the amount of THD that can be tolerated by the

AD7687. The THD degrades as a function of the source

impedance and the maximum input frequency, as shown in

Figure 29.

FREQUENCY (kHz)

THD (dB)

–60

–70

–80

–90

–100

–110

–120 0 25 50 75 100

02972-029

= 250Ω

= 100Ω

= 50Ω

= 33Ω

Figure 29. THD vs. Analog Input Frequency and Source Resistance

Data Sheet AD7687

Rev. E | Page 17 of 26

DRIVER AMPLIFIER CHOICE

Although the AD7687 is easy to drive, consider the following

when selecting a driver amplifier.

The noise generated by the driver amplifier needs to be kept as low

as possible in order to preserve the SNR and transition noise

performance of the AD7687. The AD7687 has a noise much lower

than most of the other 16-bit ADCs and, therefore, can be driven

by a noisier op amp while preserving the same or better system

performance. The noise coming from the driver is filtered by the

AD7687 analog input circuit 1-pole, low-pass filter made by RIN

and CIN or by an external filter. Because the typical noise of the

AD7687 is 53 µV rms, the SNR degradation due to the amplifier is

( )













−2

3dB

20log

LOSS Ne

SNR

where:

f–3dB is either the input bandwidth in MHz of the AD7687 (2 MHz)

or the cutoff frequency of an external filter, if one is used.

N is the noise gain of the amplifier (for example, +1 in buffer

configuration).

eN is the equivalent input noise voltage of the op amp, in nV/√Hz.

For ac applications, ensure that the THD performance of the driver

is commensurate with the AD7687 and that the driver exceeds

the THD vs. frequency shown in Figure 16.

For multichannel multiplexed applications, the driver amplifier

and the AD7687 analog input circuit must settle a full-scale step

onto the capacitor array at a 16-bit level (0.0015%, 15 ppm). Settling

at 0.1% to 0.01% is more commonly specified in the amplifier

data sheet. This can differ significantly from the settling time at

a 16-bit level and must be verified prior to driver selection.

Table 10. Recommended Driver Amplifiers.

Amplifier Typical Application

AD8021 Very low noise and high frequency

AD8022 Low noise and high frequency

AD8031 High frequency and low power

AD8519

Small, low power and low frequency

AD8605, AD8615 5 V single-supply, low power

AD8655 5 V single-supply, low noise

ADA4841-2 Very low noise, small, and low power

ADA4941-1 Very low noise, low power single-ended-to-

differential

OP184 Low power, low noise, and low frequency

SINGLE-TO-DIFFERENTIAL DRIVER

For applications using a single-ended analog signal, either bipolar

or unipolar, a single-ended-to-differential driver (like the one

shown in Figure 30) allows for a differential input into the part.

When provided a single-ended input signal, this configuration

produces a differential ±VREF with midscale at VREF/2.

10kΩ

590Ω AD7687

IN+

IN–

REF

ANALOG INPUT

(±10V, ±5V, ..)

590Ω

10µF

100nF

10kΩ

VREF

590Ω10kΩ

10kΩ

100nF

VREF

02972-030

Figure 30. Single-Ended-to-Differential Driver Circuit

VOLTAGE REFERENCE INPUT

The AD7687 voltage reference input, REF, has a dynamic input

impedance and must therefore be driven by a low impedance

source with sufficient decoupling between the REF and GND

pins (as explained in the Layout section).

For optimum performance, drive the REF pin with a low output

impedance amplifier (such as the AD8031 or the AD8605) as a

reference buffer with a 10 µF (X5R, 0805 size) ceramic chip

decoupling capacitor.

If an unbuffered reference voltage is used, the decoupling value

depends on the reference used. For instance, a 22 µF (X5R,

1206 size) ceramic chip capacitor is appropriate for optimum

performance using a low temperature drift ADR431, ADR433,

ADR434, or ADR435 reference.

If desired, smaller reference decoupling capacitor values down

to 2.2 µF can be used with a minimal impact on performance,

especially DNL.

Regardless, there is no need for an additional lower value ceramic

decoupling capacitor (for example, 100 nF) between the REF

and GND pins.

POWER SUPPLY

The AD7687 is specified for use over a wide operating range of

2.3 V to 5.5 V. Unlike other low voltage converters, it has a low

enough noise to design a 16-bit resolution system with low

voltage supplies while maintaining respectable performance. It

uses two power supply pins: a core supply, VDD, and a digital

input/output interface supply, VIO. VIO allows direct interface

with any logic between 1.8 V and VDD. VIO and VDD can be

required in the overall design. The AD7687 is independent of

power supply sequencing between VIO and VDD.

AD7687 Data Sheet

Rev. E | Page 18 of 26

Additionally, it is resistant to power supply variations over a wide

frequency range. Figure 31 shows the power supply rejection

ration (PSRR) of the device over frequency.

FREQUENCY (kHz)

PSRR (dB)

100

50 1 10 100 1000 10000

02972-031

VDD = 5V

VDD = 2.5V

Figure 31. PSRR vs. Frequency

The AD7687 powers down automatically at the end of each

conversion phase, and consequentially its power consumption

scales linearly with the sampling rate, as shown in Figure 32.

This makes the device ideal for low sampling rate (even a few

SPS) and low battery-powered applications.

SAMPLING RATE (SPS)

OPERATING CURRENT (A)

1000

0.1

0.00110 100 1000 10000 100000 1000000

02972-032

VIO

VDD = 5V

VDD = 2.5V

Figure 32. Operating Currents vs. Sampling Rate

SUPPLYING THE ADC FROM THE REFERENCE

With its low operating current, the AD7687 can be supplied

directly by the reference circuitry (see Figure 33). The reference

line is driven by one of the following:

 The system power supply directly.

 A reference voltage with enough current output capability,

such as the ADR435.

 A reference buffer, such as the AD8031, which can also

filter the system power supply (see Figure 33).

AD8031

AD7687

VIOREF VDD

10F 1F

10

10k

1F

02972-033

OPTIONAL REFERENCE BUFFER AND FILTER.

Figure 33. Example of Application Circuit

DIGITAL INTERFACE

Though the AD7687 has a reduced number of pins, it offers

flexibility in its serial interface modes.

When in CS mode, the AD7687 is compatible with SPI, QSPI,

digital hosts, and DSPs, such as the Blackfin® processors or the

high performance, mixed-signal DSP family. In this mode, the

AD7687 uses either a 3-wire or a 4-wire interface. A 3-wire

interface using the CNV, SCK, and SDO signals minimizes

wiring connections and is useful, for instance, in isolated

applications. A 4-wire interface using the SDI, CNV, SCK, and

SDO signals allows CNV, which initiates the conversions, to be

independent of the readback timing (SDI). This is useful in low

jitter sampling or simultaneous sampling applications.

When in chain mode, the AD7687 provides a daisy chain

feature using the SDI input for cascading multiple ADCs on a

single data line similar to a shift register.

The mode in which the device operates depends on the SDI

level when the CNV rising edge occurs. The CS mode is

selected if SDI is high, and the chain mode is selected if SDI is

low. The SDI hold time is such that when SDI and CNV are

connected together, the chain mode is always selected.

The initial state of SDO on power up is indeterminate. Therefore,

to put SDO in a known state, initiate a conversion and clock out

all data bits.

In either mode, the AD7687 offers the option of forcing a start

bit in front of the data bits. Use this start bit as a BUSY signal

indicator to interrupt the digital host and trigger the data

reading. Otherwise, without a BUSY indicator, the user must

time out the maximum conversion time prior to readback.

The BUSY indicator feature is enabled

 In the CS mode if CNV or SDI is low when the ADC

conversion ends (see Figure 37 and Figure 41).

 In the chain mode if SCK is high during the CNV rising

edge (see Figure 45).

Data Sheet AD7687

Rev. E | Page 19 of 26

CS MODE, 3-WIRE WITHOUT BUSY INDICATOR

This mode is usually used when a single AD7687 is connected

to an SPI-compatible digital host. Figure 34 shows the connection

diagram and Figure 35 gives the corresponding timing.

With SDI tied to VIO, a rising edge on CNV initiates a conversion,

selects the CS mode, and forces SDO to high impedance. Once

a conversion is initiated, it continues to completion irrespective

of the state of CNV. For instance, it can be useful to bring CNV

low to select other SPI devices, such as analog multiplexers, but

CNV must be returned high before the minimum conversion

time and held high until the maximum conversion time to

avoid the generation of the BUSY signal indicator (see tCONV in

Table 5). When the conversion is complete, the AD7687 enters

the acquisition phase and powers down. When CNV goes low,

the MSB is output onto SDO. The remaining data bits are then

clocked by subsequent SCK falling edges. The data is valid on

both SCK edges. Although the rising edge can capture the data,

a digital host using the SCK falling edge allows a faster reading

rate (provided it has an acceptable hold time). After the 16th

SCK falling edge, or when CNV goes high, whichever is earlier,

SDO returns to high impedance.

CNV

SCK

SDOSDI DATA IN

CLK

CONVERT

VIO DIGITAL HOST

AD7687

02972-034

Figure 34. CS Mode, 3-Wire Without BUSY Indicator

Connection Diagram (SDI High)

SDO D15 D14 D13 D1 D0

DIS

SCK

1 2 314 15 16

SCK

SCKL

SCKH

HSDO

DSDO

CNV

CONVERSION

ACQUISITION

CONV

CYC

ACQUISITION

SDI = 1

CNVH

ACQ

02972-035

Figure 35. CS Mode, 3-Wire Without BUSY Indicator Serial Interface Timing (SDI High)

AD7687 Data Sheet

Rev. E | Page 20 of 26

CS MODE, 3-WIRE WITH BUSY INDICATOR

This mode is usually used when a single AD7687 is connected

to an SPI-compatible digital host having an interrupt input.

Figure 36 shows the connection diagram and Figure 37 gives

the corresponding timing.

With SDI tied to VIO, a rising edge on CNV initiates a conversion,

selects the CS mode, and forces SDO to high impedance. SDO

is maintained in high impedance until the completion of the

conversion irrespective of the state of CNV. Prior to the minimum

conversion time, CNV can be used to select other SPI devices,

such as analog multiplexers, but CNV must be returned low

before the minimum conversion time and held low until the

maximum conversion time to guarantee the generation of the

BUSY signal indicator (see tCONV in Table 5). When the conversion

is complete, SDO goes from high to low impedance. With a

pull-up on the SDO line, this transition can be used as an

interrupt signal to initiate the data reading controlled by the

digital host. When using this option, select the value of the pull-

up resistor such that it maintains an appropriate rise time on the

SDO line for the application. This is a function of the resistance

of the pull-up and the capacitance of the SDO line. The AD7687

then enters the acquisition phase and powers down. The data

bits are then clocked out, MSB first, by subsequent SCK falling

edges. The data is valid on both SCK edges. Although the rising

edge can capture the data, a digital host using the SCK falling

edge allows a faster reading rate (provided it has an acceptable

hold time). After the optional 17th SCK falling edge, or when

CNV goes high, whichever is earlier, SDO returns to high

impedance.

If multiple AD7687 devices are selected at the same time, the

SDO output pin handles this contention without damage or

induced latch-up. Keep this contention as short as possible to

limit extra power dissipation.

DATA IN

IRQ

CLK

CONVERT

VIO DIGITAL HOST

02972-036

47kΩ

CNV

SCK

SDO

SDI

VIO

AD7687

Figure 36. CS Mode, 3-Wire with BUSY Indicator

Connection Diagram (SDI High)

SDO

D15 D14 D1 D0

DIS

SCK

1 2 3 15 16 17

SCK

SCKL

SCKH

HSDO

DSDO

CNV

CONVERSIONACQUISITION

CONV

CYC

CNVH

ACQ

ACQUISITION

SDI = 1

02972-037

Figure 37. CS Mode, 3-Wire with BUSY Indicator Serial Interface Timing (SDI High)

Data Sheet AD7687

Rev. E | Page 21 of 26

CS MODE, 4-WIRE WITHOUT BUSY INDICATOR

This mode is usually used when multiple AD7687 devices are

connected to an SPI-compatible digital host.

Figure 38 shows a connection diagram example using two

AD7687 devices and Figure 39 gives the corresponding timing.

With SDI high, a rising edge on CNV initiates a conversion,

selects the CS mode, and forces SDO to high impedance. In this

mode, CNV must be held high during the conversion phase and

the subsequent data readback (if SDI and CNV are low, SDO is

driven low). Prior to the minimum conversion time, SDI can be

used to select other SPI devices, such as analog multiplexers,

but SDI must be returned high before the minimum conversion

time and held high until the maximum conversion time to

avoid the generation of the BUSY signal indicator. When the

conversion is complete, the AD7687 enters the acquisition

phase and powers down. Each ADC result can be read by

bringing low its SDI input, which consequently outputs the

MSB onto SDO. The remaining data bits are then clocked by

subsequent SCK falling edges. The data is valid on both SCK

edges. Although the rising edge can capture the data, a digital

host using the SCK falling edge allows a faster reading rate

(provided it has an acceptable hold time). After the 16th SCK

falling edge, or when SDI goes high, whichever is earlier, SDO

returns to high impedance and another AD7687 can be read.

DATA IN

CLK

CS1

CONVERT

CS2

DIGITAL HOST

02972-038

CNV

SCK

SDOSDI

AD7687

CNV

SCK

SDOSDI

AD7687

Figure 38. CS Mode, 4-Wire Without BUSY Indicator Connection Diagram

SDO D15 D14 D13 D1 D0

tDIS

SCK 12 3 30 31 32

tHSDO tDSDO

tEN

CONVERSION

ACQUISITION

tCONV

tCYC

tACQ

ACQUISITION

SDI(CS1)

CNV

tSSDICNV

tHSDICNV

14 15

tSCK

tSCKL

tSCKH

D0 D15 D14

17 18

SDI(CS2)

02972-039

Figure 39. CS Mode, 4-Wire Without BUSY Indicator Serial Interface Timing

AD7687 Data Sheet

Rev. E | Page 22 of 26

CS MODE, 4-WIRE WITH BUSY INDICATOR

This mode is usually used when a single AD7687 is connected to

an SPI-compatible digital host, which has an interrupt input, and it

is desired to keep CNV, which is used to sample the analog input,

independent of the signal used to select the data reading. This

requirement is particularly important in applications where low

jitter on CNV is desired.

Figure 40 shows the connection diagram and Figure 41 gives

the corresponding timing.

With SDI high, a rising edge on CNV initiates a conversion,

selects the CS mode, and forces SDO to high impedance. In this

mode, CNV must be held high during the conversion phase and

the subsequent data readback (if SDI and CNV are low, SDO is

driven low). Prior to the minimum conversion time, SDI can

select other SPI devices, such as analog multiplexers, but SDI

must be returned low before the minimum conversion time and

held low until the maximum conversion time to guarantee the

generation of the BUSY signal indicator. When the conversion

is complete, SDO goes from high to low impedance. With a

pull-up on the SDO line, this transition can act as an interrupt

signal to initiate the data readback controlled by the digital host.

When using this option, select the value of the pull-up resistor

such that it maintains an appropriate rise time on the SDO line

for the application. This is a function of the resistance of the

pull-up and the capacitance of the SDO line. The AD7687 then

enters the acquisition phase and powers down. The data bits are

then clocked out, MSB first, by subsequent SCK falling edges.

The data is valid on both SCK edges. Although the rising edge

can capture the data, a digital host using the SCK falling edge

allows a faster reading rate (provided it has an acceptable hold

time). After the optional 17th SCK falling edge, or SDI going

high, whichever is earlier, the SDO returns to high impedance.

DATA IN

IRQ

CLK

CONVERT

CS1

VIO DIGITAL HOST

02972-040

47k

CNV

SCK

SDOSDI

AD7687

Figure 40. CS Mode, 4-Wire with BUSY Indicator Connection Diagram

SDO D15 D14 D1 D0

DIS

SCK 1 2 3 15 16 17

SCK

SCKL

SCKH

HSDO

DSDO

CONVERSION

CQUISITION

CONV

CYC

ACQ

ACQUISITION

SDI

CNV

SSDICNV

HSDICNV

02972-041

Figure 41. CS Mode, 4-Wire with BUSY Indicator Serial Interface Timing

Data Sheet AD7687

Rev. E | Page 23 of 26

CHAIN MODE WITHOUT BUSY INDICATOR

Use this mode to daisy-chain multiple AD7687 devices on a

3-wire serial interface. This feature is useful for reducing

component count and wiring connections, for isolated

multiconverter applications, or for systems with a limited

interfacing capacity (for example). Data readback is analogous

to clocking a shift register.

Figure 42 shows a connection diagram example using two

AD7687 devices and Figure 43 gives the corresponding timing.

When SDI and CNV are low, SDO is driven low. With SDI and

SCK low, a rising edge on CNV initiates a conversion, selects

the chain mode, and disables the BUSY indicator. In this mode,

CNV is held high during the conversion phase and the subsequent

data readback. When the conversion is complete, the MSB is

output onto SDO and the AD7687 enters the acquisition phase

and powers down. The remaining data bits stored in the

internal shift register are then shifted out by subsequent SCK

falling edges. For each ADC, SDI feeds the input of the internal

shift register; these data bits are also shifted in by the SCK

falling edge. Each of the N ADCs in the chain outputs its data

MSB first. The data is valid on both SCK edges. Although the

rising edge can capture the data, a digital host using the SCK

falling edge allows a faster reading rate and, consequently, more

AD7687 devices in the chain (provided the digital host has an

acceptable hold time). After the 16 × Nth SCK falling edge or

CNV rising edge, whichever is earlier, SDO is driven low again.

The maximum conversion rate can be reduced due to the total

readback time. For example, using a digital host with a 3 ns set-

up time and 3 V interface, up to eight AD7687 devices daisy-

chained on a 3-wire port can be run at a maximum effective

conversion rate of 220 kSPS.

CLK

CONVERT

DATA IN

DIGITAL HOST

02972-042

CNV

SCK

SDOSDI

AD7687

CNV

SCK

SDOSDI

AD7687

Figure 42. Chain Mode Without BUSY Indicator Connection Diagram

SDO

= SDI

15 D

14 D

SCK 1 2 3 30 31 32

SSDISCK

HSDISC

CONVERSIONACQUISITION

CONV

CYC

ACQ

ACQUISITION

CNV

14 15

SCK

SCKL

SCKH

17 1816

SDI

= 0

SDO

15 D

14 D

13 D

1 D

0 D

15 D

HSDO

DSDO

SSCKCNV

HSCKCNV

02972-043

Figure 43. Chain Mode Without BUSY Indicator Serial Interface Timing

AD7687 Data Sheet

Rev. E | Page 24 of 26

CHAIN MODE WITH BUSY INDICATOR

This mode can also be used to daisy-chain multiple AD7687

devices on a 3-wire serial interface while providing a BUSY

indicator. This feature is useful for reducing component count

and wiring connections, for isolated multiconverter applications

or for systems with a limited interfacing capacity (for example).

Data readback is analogous to clocking a shift register.

Figure 44 shows a connection diagram example using three

AD7687 devices, and Figure 45 gives the corresponding timing.

When SDI and CNV are low, SDO is driven low. With SDI low

and SCK high, a rising edge on CNV initiates a conversion,

selects the chain mode, and enables the BUSY indicator feature.

In this mode, CNV is held high during the conversion phase

and the subsequent data readback. When all ADCs in the chain

have completed their conversions, the SDO pin of the ADC

closest to the digital host (see the AD7687 C in Figure 44) is driven

high. This transition on SDO can act as a BUSY indicator to

trigger the data readback controlled by the digital host. The

AD7687 then enters the acquisition phase and powers down.

The data bits stored in the internal shift register are then

clocked out, MSB first, by subsequent SCK falling edges. For

each ADC, SDI feeds the input of the internal shift register;

these data bits are also shifted in by the SCK falling edge. Each

of the N ADCs in the chain outputs its data MSB first. The data

is valid on both SCK edges. Although the rising edge can capture

the data, a digital host using the SCK falling edge allows a faster

reading rate and, consequently, more AD7687 devices in the

chain (provided the digital host has an acceptable hold time).

After the optional (16 × N) + 1th SCK falling edge or CNV

rising edge, whichever is earlier, SDO is driven low again. The

maximum conversion rate may be reduced due to the total

readback time. For example, using a digital host with a 3 ns set-

up time and 3 V interface, up to eight AD7687 devices daisy-

chained on a 3-wire port can be run at a maximum effective

conversion rate of 220 kSPS.

CLK

CONVERT

DATA IN

IRQ

DIGITAL HOST

02972-044

CNV

SCK

SDOSDI

AD7687

CNV

SCK

SDOSDI

AD7687

CNV

SCK

SDOSDI

AD7687

Figure 44. Chain Mode with BUSY Indicator Connection Diagram

SDO

= SDI

15 D

14 D

SCK 1 2 3 35 47 48

CONVERSION

ACQUISITION

CONV

CYC

ACQ

ACQUISITION

CNV = SDI

4 15

SCK

SCKH

SCKL

17 3416

SDO

= SDI

15 D

14 D

13 D

1 D

0 D

15 D

SSDISCK

HSDISC

HSDO

DSDO

SDO

15 D

14 D

13 D

1 D

0 D

19 31 3218 33

1 D

0 D

15D

15 D

DSDOSDI

SSCKCNV

HSCKCNV

02972-045

DSDOSDI

Figure 45. Chain Mode with BUSY Indicator Serial Interface Timing

Data Sheet AD7687

Rev. E | Page 25 of 26

APPLICATIONS INFORMATION

LAYOUT

Providing a steady and stable reference voltage to the AD7687 is

critical for device operation. Prioritize design tasks aimed at

preventing voltage fluctuations at this node. Decouple the REF

pin, which has a dynamic input impedance, with minimal parasitic

inductances (see the Converter Operation Section). Achieve this

by placing the reference decoupling ceramic capacitor as close as

physically possible the REF and GND pins and connecting it

with wide, low impedance traces.

Limiting sources of noise on the analog signal nodes is

imperative in high precision ADC systems. The digital lines

controlling the AD7687 have the potential to radiate noise that

can couple into the analog signals; therefore, ensure that these

two types of signals are separated and confined to different

areas of boards housing the AD7687. Never allow fast switching

signals (such as CNV or clocks) to run near analog signal paths,

and avoid physical crossover of digital and analog signals. Do

not route digital lines under the AD7687 without a ground

plane providing adequate isolation between the two. To

facilitate these design tasks, the analog and digital pins are

located on separate sides of the device (see Figure 46).

Printed circuit boards (PCBs) housing the AD7687 must contain

at least one ground plane. Connecting analog and digital ground

on the board is not required; however, connecting these planes

underneath the AD7687 is recommended.

Finally, decouple the power supply pins of the AD7687 (VDD

and VIO) with ceramic capacitors (typically 100 nF) placed

close to the AD7687 and connected using short and wide traces

to provide low impedance paths and reduce the effect of glitches

on the power supply lines.

Figure 46 and Figure 47 show an example of a layout following

these rules.

02972-046

Figure 46. Example of Layout of the AD7687 (Top Layer)

02972-047

Figure 47. Example of Layout of the AD7687 (Bottom Layer)

EVALUATING THE PERFORMANCE OF THE AD7687

The EVAL-AD7687SDZ evaluation board documentation

outlines other recommended layouts for the AD7687. The

evaluation board package includes a fully assembled and tested

evaluation board, documentation, and software for controlling

the board from a PC via the EVAL-SDP-CB1Z.

AD7687 Data Sheet

Rev. E | Page 26 of 26

OUTLINE DIMENSIONS

COMPLIANT TO JEDEC STANDARDS MO-187-BA

091709-A

6°

0°

0.70

0.55

0.40

0.50 BSC

0.30

0.15

1.10 MAX

3.10

3.00

2.90

COPLANARITY

0.10

0.23

0.13

3.10

3.00

2.90

5.15

4.90

4.65

PIN 1

IDENTIFIER

15° MAX

0.95

0.85

0.75

0.15

0.05

Figure 48. 10-Lead Mini Small Outline Package [MSOP]

(RM-10)

Dimensions shown in millimeters

2.48

2.38

2.23

0.50

0.40

0.30

0.25

0.20

PIN 1 INDEX

AREA

SEATING

PLANE

0.80

0.75

0.70

1.74

1.64

1.49

0.20 REF

0.05 M AX

0.02 NO M

0.50 BSC

EXPOSED

PAD

3.10

3.00 SQ

2.90

PIN 1

INDICATOR

(R 0. 15)

FO R P ROPE R CONNECT ION OF

THE EXPOSED PAD, REFER TO

THE P IN CO NFIGURATIO N AND

FUNCTION DESCRIPT IO NS

SECTION OF THIS DATA SHEET.

COPLANARITY

0.08

02-05-2013-C

TOP VIEW BOTTOM VIEW

0.20 M I N

Figure 49. 10-Lead Lead Frame Chip Scale Package [LFCSP_WD]

3 mm × 3 mm Body, Very Very Thin, Dual Lead

(CP-10-9)

Dimensions shown in millimeters

ORDERING GUIDE

Model1, 2, 3 Integral Nonlinearity Temperature Range Package Description

Package

Option

Ordering

Quantity Branding

AD7687BRMZ ±1.5 LSB −40°C to +85°C 10-Lead MSOP, Tube RM-10 50 C3Q

AD7687BRMZRL7

±1.5 LSB

−40°C to +85°C

10-Lead MSOP, Reel

RM-10

1,000

C3Q

AD7687BCPZ-R2 ±1.5 LSB −40°C to +85°C 10-Lead LFCSP_WD, Reel CP-10-9 250 C3Q

AD7687BCPZRL7 ±1.5 LSB −40°C to +85°C 10-Lead LFCSP_WD, Reel CP-10-9 1,500 #C03

EVAL-AD7687SDZ Evaluation Board

EVAL-SDP-CB1Z Controller Board

1 Z = RoHS Compliant Part, # denotes RoHS compliant product, may be top or bottom marked.

2 The EVAL-AD7687SDZ can be used as a standalone evaluation board or in conjunction with the EVAL-SDP-CB1Z for evaluation and/or demonstration purposes.

3 The EVAL-SDP-CB1Z allows a PC to control and communicate with all Analog Devices, Inc. evaluation boards ending in the SDZ designator.

registered trademarks are the property of their respective owners.

D02972-0-12/15(E)