PWM-60 60W PWM output LED power supply F 110 M Features Universal AC input / Full range (up to 305VAC) Built-in active PFC function Constant voltage PWM style output Built-in 3 in 1 dimming function M SELV series IP67 Applications LED strip lighting Indoor LED lighting LED decorative lighting LED architecture lighting (0~10Vdc or PWM signal or resistance) Dimming range : 0~100% High efficiency up to 90% Protections: Short circuit / Over load / Over voltage / Over temperature Class power unit, no FG Class 2 power unit Suitable for dry / damp / wet locations No load power consumption<0.5W 5 years warranty Description PWM-60 is one 60W waterproof constant-voltage output LED power supply series. Differentiating from general DC output power supplies, PWM-60 transmits PWM style output, adapting to directly driving all kinds of LED strips that the color temperature can be maintained and the brightness homogeneity can be assured. Adopting a universal input range between 90VAC and 305VAC and incorporating the built-in PFC function, this series is also designed with a 3 in 1 dimming function (0~10Vdc or PWM signal or resistance) that simplifies the brightness adjustment for system designers so as to achieve light reduction and energy conservation. Providing a high efficiency up to 90% and a low no load power consumption below 0.5W, PWM-60 can satisfy the energy saving demand for the new generation LED lighting. The class design (without FG pin) and the double insulation weather-resistant cable (SJTW) on the input side make it convenient for users to flexibly install on various types of lighting systems. The enclosure design is a 94V-0 flame retardant plastic case. The interior is fully potted with silicone that enhances the heat dissipation and allows PWM-60 to meet the anti-vibration demand up to 5G; it also thus conforms to IP67 level, enabling PWM-60 to be used in a highly dusty and highly humid harsh environment. The entire series can operate under the temperature between -40~+70 and comply with the relevant global lighting safety certification. Model Encoding PWM - 60 - 12 Output voltage Output wattage Series name File Name:PWM-60-SPEC 2015-05-28 PWM-60 60W PWM output LED power supply series SPECIFICATION MODEL DC VOLTAGE PWM-60-12 PWM-60-24 PWM-60-36 PWM-60-48 12V 24V 36V 48V CONSTANT CURRENT REGION 5A OUTPUT RATED POWER 60W DIMMING RANGE 0 ~ 100% PWM FREQUENCY (Typ.) 300Hz VOLTAGE TOLERANCE 4.0% SETUP, RISE TIME Note.2 500ms, 80ms at 95% load INPUT 2.5A 1.67A 1.25A 60W 60.12W 60W 3.0% 2.0% 1.0% 115VAC / 230VAC HOLD UP TIME (Typ.) 16ms/230VAC VOLTAGE RANGE 90 ~ 305VAC FREQUENCY RANGE 47 ~ 63Hz POWER FACTOR (Typ.) PF>0.97/115VAC, PF>0.95/230VAC, PF>0.92/277VAC at full load (Please refer to "Power Factor Characteristic" curve) 16ms/115VAC at full load 127 ~ 431VDC TOTAL HARMONIC DISTORTION THD< 20% when output loading60% at 115VAC/230VAC input and output loading75% at 277VAC input EFFICIENCY (Typ.) 86% AC CURRENT (Typ.) 0.8A / 115VAC INRUSH CURRENT(Typ.) COLD START 50A(twidth=270s measured at 50% Ipeak) at 230VAC 89% 0.4A / 230VAC 90% 90% 0.32A / 277VAC MAX. NO. of PSUs on 16A 9 units (circuit breaker of type B) / 16 units (circuit breaker of type C) at 230VAC CIRCUIT BREAKER LEAKAGE CURRENT <0.25mA / 277VAC SHORT CIRCUIT Hiccup mode, recovers automatically after fault condition is removed OVER LOAD PROTECTION 108 ~ 120% rated output power Protection type : Hiccup mode, recovers automatically after fault condition is removed 15 ~ 17V OVER VOLTAGE 28 ~ 34V 41 ~ 46V 54 ~ 60V Protection type : Shut down o/p voltage, re-power on to recover OVER TEMPERATURE Shut down o/p voltage, re-power on to recover WORKING TEMP. -40 ~ +70 (Refer to "Derating Curve") WORKING HUMIDITY 20 ~ 95% RH non-condensing ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +80, 10 ~ 95% RH TEMP. COEFFICIENT 0.03%/ (0 ~ 50) VIBRATION 10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes SAFETY STANDARDS UL8750, CSA C22.2 No. 250.13-12, ENEC EN61347-1, EN61347-2-13, EN62384 independent, IP67 approved; Design refer to EN60335-1 SAFETY & WITHSTAND VOLTAGE EMC ISOLATION RESISTANCE I/P-O/P:100M Ohms / 500VDC / 25/ 70% RH EMC EMISSION Compliance to EN55015, EN61000-3-2 Class C (60% load) ; EN61000-3-3 EMC IMMUNITY Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, light industry level(surge L-N: 2KV), criteria A MTBF 271.03K hrs min. OTHERS DIMENSION PACKING NOTE I/P-O/P:3.75KVAC MIL-HDBK-217F (25) 150*53*35mm (L*W*H) 0.49Kg;30pcs/15.7Kg/1.0CUFT 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature. 2. Length of set up time is measured at cold first start. Turning ON/OFF the power supply may lead to increase of the set up time. File Name:PWM-60-SPEC 2015-05-28 PWM-60 60W PWM output LED power supply series Block Diagram PFC fosc : 50~120KHz PWM fosc : 60~130KHz EMI FILTER & RECTIFIERS I/P +V RECTIFIERS & FILTER POWER SWITCHING PFC CIRCUIT DIMMING CIRCUIT -V O.L.P. O.T.P. O.L.P. DIM+ DIM- DETECTION CIRCUIT PWM & PFC CONTROL O.V.P. Derating Curve Static Characteristics 100 100 90 80 230VAC Input only 80 70 50 LOAD (%) LOAD (%) 60 40 20 -40 -25 -10 0 15 30 50 60 70 (HORIZONTAL) 60 50 40 90 100 125 AMBIENT TEMPERATURE () 135 145 155 165 175 180 200 230 305 INPUT VOLTAGE (V) 60Hz Power Factor Characteristic Constant Current Mode 1.0 0.9 PF 0.8 0.7 277V 0.6 230V 115V 0.5 0.4 0.3 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% (60W) LOAD File Name:PWM-60-SPEC 2015-05-28 PWM-60 60W PWM output LED power supply series EFFICIENCY vs LOAD (48V Model) PWM-60 series possess superior working efficiency that up to 90% can be reached in field applications. 92% EFFICIENCY (%) 90% 88% 277V 230V 115V 86% 84% 82% 80% 78% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% LOAD DIMMING OPERATION The PWM style output is a simple switching of supply ON/OFF at a rate so fast that the human eye cannot see led flickering. Duty cycle describes the proportion of time when output voltage is on relative to the entire period of time. It is expressed in percentage, 100% being fully on (maximal brightness) and a low duty cycle corresponding to lower brightness. Built-in 3 in 1 dimming function. The duty of the PWM style output can be adjusted through output cable by connecting a 0~10Vdc or 10V PWM signal or resistance between DIM+ and DIM-. Connection LED Strips +V -V + + - DIM+ + 0~10Vdc or 10V PWM or resistance control dimmer DIM- - "DO NOT connect "DIM- to -V" File Name:PWM-60-SPEC 2015-05-28 PWM-60 60W PWM output LED power supply series Duty cycle of output current VS Dimming input 100% when DIM+/DIM- are open circuit. 100% 90% Duty cycle of output current 80% Note 70% Note : The output current drops down to 0% when the dimming input is about 6 Kor 0.6Vdc, or 10V PWM signal with 6% duty cycle. Non-Linear 60% 50% 40% 30% 20% 10% 0% 0V 1V 2V 3V 4V 5V 6V 7V 8V 9V 10V 0% 10% 20% 30% 40% 50% 60% 70% 80% 90% 100% Short 10K 20K 30K 40K 50K 60K 70K 80K 90K 100K Dimming input 0~10V Duty cycle of 10V PWM (frequency range = 100~3KHz) Short~100Kresistance PWM Style Output Output DC current ON Duty cycle(%) = T ON T 100% Output PWM frequency : 300Hz fixed (Typ.) OFF T ON T Mechanical Specification Case No.: NPF-60A Unit:mm 150 5 5 30020 30020 53 AC/L(Brown) AC/N(Blue) 4.5 35 13 T case 5 SJTW 18AWGx2C UL2464 18AWGx2C(+V,-V) UL2464 22AWGx2C(DIM+,DIM-) +V(Red) -V(Black) DIM+(Blue) DIM-(White) 5 35 T case: Max. Case Temperature Recommend Mounting Direction File Name:PWM-60-SPEC 2015-05-28 PWM-60 60W PWM output LED power supply series Installation Manual Connection +V(RED) AC/L(BROWN) AC/N(BLUE) -V(BLACK) + - LED Strip DIM+(BLUE) + - 0~10Vdc or 10V PWM or resistance Dimmer DIM-(WHITE) Cautions Before commencing any installation or maintenance work, please disconnect the power supply from the utility. Ensure that it cannot be re-connected inadvertently! Keep proper ventilation around the unit and do not stack any object on it. Also a 10-15 cm clearance must be kept when the adjacent device is a heat source. Mounting orientations other than standard orientation or operate under high ambient temperature may increase the internal component temperature and will require a de-rating in output current. Current rating of an approved primary /secondary cable should be greater than or equal to that of the unit. Please refer to its specification. For LED power supplies with waterproof connectors, verify that the linkage between the unit and the lighting fixture is tight so that water cannot intrude into the system. For dimmable LED power supplies, make sure that your dimming controller is capable of driving these units.PWM series require 0.15mA each unit. Tc max. is identified on the product label. Please make sure that temperature of Tc point will not exceed limit. DO NOT connect "DIM+ to -V". Suitable for indoor use or outdoor use without direct sunlight exposure. Please avoid immerse in the water over 30 minutes. The power supply is considered as a component that will be operated in combination with final equipment. Since EMC performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC Directive on the complete installation again. For more information about installation, please refer to www.meanwell.com/webnet/search/installationsearch.html for details. File Name:PWM-60-SPEC 2015-05-28 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Mean Well: PWM-60-48 PWM-60-12 PWM-60-24 PWM-60-36