■Description
PWM-60 is one 60W waterproof constant-voltage output LED power supply series. Differentiating from
general DC output power supplies, PWM-60 transmits PWM style output, adapting to directly driving
all kinds of LED strips that the color temperature can be maintained and the brightness homogeneity
can be assured. Adopting a universal input range between 90VAC and 305VAC and incorporating the
built-in PFC function, this series is also designed witha3in1dimming function (0~10Vdc or PWM
signal that simplifies the brightness adjustment for system designers so as to achieveor resistance)
light reduction and energy conservation.
Universal AC input / Full range (up to 305VAC)
Built-in active PFC function
Constant voltage PWM style output
Built-in 3 in 1 dimming function
(0~10Vdc or PWM signal or resistance)
Dimming range : 0~100%
High efficiency up to 90%
Protections: Short circuit / Over load / Over voltage
/ Over temperature
Class power unit, no FGⅡ
Class 2 power unit
Suitable for dry / damp / wet locations
No load power consumption<0.5W
5 years warranty
■Features ■Applications
60W PWM output LED power supply PWM-60 series
File Name:PWM-60-SPEC 2015-05-28
IP67
FMM
110
SELV
■Model Encoding
-12
PWM - 60
Output voltage
Output wattage
Series name
Providing a high efficiency up to 90% and a low no load power consumption below 0.5W, PWM-60 can
satisfy the energy saving demand for the new generation LED lighting. The class design (without FGⅡ
pin) and the double insulation weather-resistant cable (SJTW) on the input side make it convenient for
users to flexibly install on various types of lighting systems. The enclosure design is a 94V-0 flame
retardant plastic case. The interior is fully potted with silicone that enhances the heat dissipation and
allows PWM-60 to meet the anti-vibration demand up to 5G; it also thus conforms to IP67 level, enabling
PWM-60 to be used in a highly dusty and highly humid harsh environment. The entire series can operate
under the temperature between -40~+70 and comply with the relevant global lighting safety certification.℃
LED strip lighting
Indoor LED lighting
LED decorative lighting
LED architecture lighting
60W PWM output LED power supply PWM-60 series
File Name:PWM-60-SPEC 2015-05-28
DIMMING RANGE
SPECIFICATION
MODEL
DC VOLTAGE
CONSTANT CURRENT REGION
RATED POWER
OUTPUT
SETUP, RISE TIME Note.2
HOLD UP TIME (Typ.)
VOLTAGE RANGE
FREQUENCY RANGE
POWER FACTOR (Typ.)
EFFICIENCY (Typ.)
AC CURRENT (Typ.)
INPUT
INRUSH CURRENT(Typ.)
LEAKAGE CURRENT
SAFETY STANDARDS
WORKING TEMP.
WORKING HUMIDITY
STORAGE TEMP., HUMIDITY
TEMP. COEFFICIENT
VIBRATION
MTBF
DIMENSIONOTHERS
NOTE
PACKING
OVER LOAD
OVER VOLTAGE
OVER TEMPERATURE
16ms/230VAC 16ms/115VAC at full load
90 ~ 305VAC 127 ~ 431VDC
47 ~ 63Hz
Compliance to EN55015, EN61000-3-2 Class C ( 60% load) ; EN61000-3-3≧
Compliance to EN61000-4-2,3,4,5,6,8,11; EN61547, light industry level(surge L-N: 2KV), criteria A
20 ~ 95% RH non-condensing
-40 ~ +80 , 10 ~ 95% RH℃
±℃ ℃0.03%/ (0 ~ 50 )
10 ~ 500Hz, 5G 12min./1cycle, period for 72min. each along X, Y, Z axes
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.℃
2. Length of set up time is measured at cold first start. Turning ON/OFF the power supply may lead to increase of the set up time.
0.49Kg;30pcs/15.7Kg/1.0CUFT
VOLTAGE TOLERANCE
ENVIRONMENT
SAFETY &
EMC
PROTECTION
500ms, 80ms at 95% load 115VAC / 230VAC
EMC IMMUNITY
EMC EMISSION
COLD START 50A(twidth=270 s measured at 50% Ipeak) at 230VAC
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
-40 ~ +70 (Refer to "Derating Curve")℃
TOTAL HARMONIC DISTORTION
UL8750, CSA C22.2 No. 250.13-12, ENEC EN61347-1, EN61347-2-13, EN62384 independent,
I/P-O/P:3.75KVAC
I/P-O/P:100M Ohms / 500VDC / 25 / 70% RH℃
IP67 approved; Design refer to EN60335-1
μ
271.03K hrs min. MIL-HDBK-217F (25 )℃
PF>0.97/115VAC, PF>0.95/230VAC, PF>0.92/277VAC at full load (Please refer to "Power Factor Characteristic" curve)
THD< 20% when output loading 60% at 115VAC/230VAC input and output loading 75% at 277VAC input≧≧
0.8A / 115VAC 0.4A / 230VAC 0.32A / 277VAC
<0.25mA / 277VAC
150*53*35mm (L*W*H)
PWM FREQUENCY (Typ.)
12V 24V 36V 48V
0 ~ 100%
300Hz
±4.0% ±3.0% ±2.0% ±1.0%
PWM-60-12 PWM-60-24 PWM-60-36 PWM-60-48
86% 89% 90% 90%
15 ~ 17V 28 ~ 34V 41 ~ 46V 54 ~ 60V
108 ~ 120% rated output power
Protection type : Hiccup mode, recovers automatically after fault condition is removed
Protection type : Shut down o/p voltage, re-power on to recover
Shut down o/p voltage, re-power on to recover
5A 2.5A 1.67A 1.25A
60W 60W 60.12W 60W
SHORT CIRCUIT Hiccup mode, recovers automatically after fault condition is removed
MAX. NO. of PSUs on 16A
CIRCUIT BREAKER 9 units (circuit breaker of type B) / 16 units (circuit breaker of type C) at 230VAC
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
277V
230V
115V
LOAD (%)
INPUT VOLTAGE (V) 60Hz
90 100 125 135 145 155 165 175 180 200 230 305
100
90
80
70
60
50
40
LOAD (%)
Derating Curve
LOAD (%)
Derating Curve Static Characteristics
AMBIENT TEMPERATURE ( )℃
LOAD (%)
175
LOAD (%)
(HORIZONTAL)
Block Diagram
DETECTION
DIMMING
PWM & PFC CIRCUIT
CIRCUIT
O.L.P.O.T.P.
EMI FILTER
RECTIFIERS
POWER
SWITCHING
FILTER
&
RECTIFIERS +V
-V
I/P
CONTROL
O.V.P.
&
O.L.P.
PFC
CIRCUIT
PFC fosc : 50~120KHz
PWM fosc : 60~130KHz
DIM+
DIM-
60W PWM output LED power supply PWM-60 series
File Name:PWM-60-SPEC 2015-05-28
-40 -25 -10 0 15 30 50 60 70
20
40
60
80
100
230VAC
Input only
50
PF
LOAD
(60W)
Power Factor Characteristic
Constant Current Mode
Built-in 3 in 1 dimming function. The duty of the PWM style output can be adjusted through output cable by connecting
a 0~10Vdc or 10V PWM signal or resistance between DIM+ and DIM-.
DIMMING OPERATION
◎Connection
LED Strips
0~10Vdc or 10V PWM or resistance control dimmer
+V
-V
DIM+
DIM-
++
+
--
-
“DO NOT connect "DIM- to -V"
60W PWM output LED power supply PWM-60 series
File Name:PWM-60-SPEC 2015-05-28
The PWM style output is a simple switching of supply ON/OFF at a rate so fast that the human eye cannot see led flickering.
Duty cycle describes the proportion of time when output voltage is on relative to the entire period of time. It is expressed
in percentage, 100% being fully on (maximal brightness) and a low duty cycle corresponding to lower brightness.
LOAD
EFFICIENCY (%)
PWM-60 series possess superior working efficiency that up to 90% can be reached in field applications.
EFFICIENCY vs LOAD (48V Model)
78%
80%
82%
84%
86%
88%
90%
92%
10% 20% 30% 40% 50% 60% 70% 80% 90% 100%
277V
230V
115V
60W PWM output LED power supply PWM-60 series
File Name:PWM-60-SPEC 2015-05-28
◎PWM Style Output
ON
OFF
TON
T
Output DC current
Output PWM frequency : 300Hz fixed (Typ.)
Duty cycle(%) = ⊙100%
TON
T
UL2464 18AWG 2C(+V,-V)×
UL2464 22AWG 2C(DIM+,DIM-)×
Mechanical Specification
Recommend Mounting Direction
+V(Red)
DIM+(Blue)
-V(Black)
DIM-(White)
Case No.: NPF-60A Unit:mm
SJTW 18AWG 2C×
AC/L(Brown)
AC/N(Blue)
※T case: Max. Case Temperature
Tcase
35
150
53
5
5
5
5
ψ4.5
35
13
300±20
300±20
Non-Linear
0V
0%
1V
10%
2V
20%
3V
30%
4V
40%
5V
50%
Dimming input
6V
60%
7V
70%
8V
80%
9V
90%
10V 0~10V
100%
Duty cycle of 10V PWM (frequency range = 100~3KHz)
10%
0%
20%
30%
40%
50%
60%
70%
80%
90%
100%
◎Duty cycle of output current VS Dimming input
Short~100K resistanceΩ
Short
10K 20K 30K 40K 50K 60K 70K 80K 90K 100K
100% when DIM+/DIM- are open circuit.
Duty cycle of output current
※Note : The output current drops down to 0% when the dimming input is about
6 or 0.6Vdc, or 10V PWM signal with 6% duty cycle.KΩ
Note
File Name:PWM-60-SPEC 2015-05-28
60W PWM output LED power supply PWM-60 series
Installation Manual
AC/L(BROWN)
+V(RED)
-V(BLACK)
DIM-(WHITE)
DIM+(BLUE)
AC/N(BLUE)
◎
Connection
◎
Cautions
Before commencing any installation or maintenance work, please disconnect the power supply from the utility. Ensure
that it cannot be re-connected inadvertently!
Keep proper ventilation around the unit and do not stack any object on it. Also a 10-15 cm clearance must be kept when
the adjacent device is a heat source.
Mounting orientations other than standard orientation or operate under high ambient temperature may increase the
internal component temperature and will require a de-rating in output current.
Current rating of an approved primary /secondary cable should be greater than or equal to that of the unit. Please refer
to its specification.
For LED power supplies with waterproof connectors, verify that the linkage between the unit and the lighting fixture is
tight so that water cannot intrude into the system.
For dimmable LED power supplies, make sure that your dimming controller is capable of driving these units.PWM series
require 0.15mA each unit.
Tc max. is identified on the product label. Please make sure that temperature of Tc point will not exceed limit.
DO NOT connect "DIM+ to -V".
Suitable for indoor use or outdoor use without direct sunlight exposure. Please avoid immerse in the water over 30
minutes.
The power supply is considered as a component that will be operated in combination with final equipment. Since EMC
performance will be affected by the complete installation, the final equipment manufacturers must re-qualify EMC
Directive on the complete installation again.
For more information about installation, please refer towww.meanwell.com/webnet/search/installationsearch.html
for details.
+
-
LED Strip
+
-
0~10Vdc or 10V PWM
or resistance Dimmer
