LTC2471/LTC2473 Selectable 208sps/833sps, 16-Bit I2C ADCs with 10ppm/C Max Precision Reference Description Features n n n n n n n n n n n n n 16-Bit Resolution Internal, High Accuracy Reference--10ppm/C (Max) Single-Ended (LTC2471) or Differential (LTC2473) Selectable 208sps/833sps Output Rate 1mV Offset Error 0.01% Gain Error Single Conversion Settling Time Simplifies Multiplexed Applications Single-Cycle Operation with Auto Shutdown 3.5mA (Typ) Supply Current 2A (Max) Sleep Current Internal Oscillator--No External Components Required I2C Interface Small 12-Lead, 3mm x 3mm DFN and MSOP Packages Following a single conversion, the LTC2471/LTC2473 automatically power down the converter and can also be configured to power down the reference. When both the ADC and reference are powered down, the supply current is reduced to 200nA. Applications n n n n n n n The LTC(R)2471/LTC2473 are small, 16-bit analog-to-digital converters with an integrated precision reference and a selectable 208sps or 833sps output rate. They use a single 2.7V to 5.5V supply and communicate through an I2C Interface. The LTC2471 is single-ended with a 0V to VREF input range and the LTC2473 is differential with a VREF input range. Both ADCs include a 1.25V integrated reference with 2ppm/C drift performance and 0.1% initial accuracy. The converters are available in a 12-pin DFN 3mm x 3mm package or an MSOP-12 package. They include an integrated oscillator and perform conversions with no latency for multiplexed applications. The LTC2471/ LTC2473 include a proprietary input sampling scheme that reduces the average input current several orders of magnitude when compared to conventional delta sigma converters. System Monitoring Environmental Monitoring Direct Temperature Measurements Instrumentation Industrial Process Control Data Acquisition Embedded ADC Upgrades L, LT, LTC, LTM, Linear Technology and the Linear logo are registered trademarks of Linear Technology Corporation and Easy Drive and No Latency is a trademark of Linear Technology Corporation. All other trademarks are the property of their respective owners. Protected by U.S. Patents, including 6208279, 6411242, 7088280, 7164378. The LTC2471/LTC2473 include a user selectable 208sps or 833sps output rate and due to a large oversampling ratio (8,192 at 208sps and 2,048 at 833sps) have relaxed anti-aliasing requirements. Typical Application VREF vs Temperature 1.2520 0.1F 0.1F 0.1F 10k REFOUT SCL LTC2473 IN- 10k R 0.1F REF- 10F COMP VCC IN+ 10k 0.1F AO SDA GND 2 I C INTERFACE REFERENCE OUTPUT VOLTAGE (V) 2.7V TO 5.5V 1.2515 1.2510 1.2505 1.2500 1.2495 1.2490 1.2485 24713 TA01a 1.2480 -50 -30 -10 10 30 50 TEMPERATURE (C) 70 90 24713 TA01b 24713fb For more information www.linear.com/LTC2471 1 LTC2471/LTC2473 Absolute Maximum Ratings (Notes 1, 2) Supply Voltage (VCC).................................... -0.3V to 6V Analog Input Voltage (VIN+, VIN -, VIN, VREF -, VCOMP, VREFOUT )...........-0.3V to (VCC + 0.3V) Digital Voltage (VSDA, VSCL, VAO).....-0.3V to (VCC + 0.3V) Storage Temperature Range................... -65C to 150C Operating Temperature Range LTC2471C/LTC2473C................................ 0C to 70C LTC2471I/LTC2473I..............................-40C to 85C Pin Configuration LTC2473 LTC2473 TOP VIEW REFOUT 1 12 VCC COMP 2 11 GND 10 IN- AO 3 GND 4 SCL 5 8 REF- SDA 6 7 GND 13 GND TOP VIEW REFOUT COMP AO GND SCL SDA 9 IN+ DD PACKAGE 12-LEAD (3mm x 3mm) PLASTIC DFN TJMAX = 125C, JA = 43C/W EXPOSED PAD (PIN 13) PCB GROUND CONNECTION 1 2 3 4 5 6 12 11 10 9 8 7 VCC GND IN- IN+ REF- GND MS PACKAGE 12-LEAD PLASTIC MSOP TJMAX = 125C, JA = 130C/W LTC2471 LTC2471 TOP VIEW TOP VIEW 12 VCC REFOUT 1 COMP 2 AO 3 GND 4 SCL 5 8 REF- SDA 6 7 GND REFOUT COMP AO GND SCL SDA 11 GND 13 GND 10 GND 9 IN DD PACKAGE 12-LEAD (3mm x 3mm) PLASTIC DFN TJMAX = 125C, JA = 43C/W EXPOSED PAD (PIN 13) PCB GROUND CONNECTION 1 2 3 4 5 6 12 11 10 9 8 7 VCC GND GND IN REF- GND MS PACKAGE 12-LEAD PLASTIC MSOP TJMAX = 125C, JA = 130C/W Order Information LEAD FREE FINISH TAPE AND REEL PART MARKING* PACKAGE DESCRIPTION TEMPERATURE RANGE LTC2471CDD#PBF LTC2471CDD#TRPBF LFPW 12-Lead Plastic (3mm x 3mm) DFN 0C to 70C LTC2471IDD#PBF LTC2471IDD#TRPBF LFPW 12-Lead Plastic (3mm x 3mm) DFN -40C to 85C LTC2471CMS#PBF LTC2471CMS#TRPBF 2471 12-Lead Plastic MSOP 0C to 70C LTC2471IMS#PBF LTC2471IMS#TRPBF 2471 12-Lead Plastic MSOP -40C to 85C LTC2473CDD#PBF LTC2473CDD#TRPBF LFPX 12-Lead Plastic (3mm x 3mm) DFN 0C to 70C LTC2473IDD#PBF LTC2473IDD#TRPBF LFPX 12-Lead Plastic (3mm x 3mm) DFN -40C to 85C LTC2473CMS#PBF LTC2473CMS#TRPBF 2473 12-Lead Plastic MSOP 0C to 70C LTC2473IMS#PBF LTC2473IMS#TRPBF 2473 12-Lead Plastic MSOP -40C to 85C Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container. Consult LTC Marketing for information on non-standard lead based finish parts. For more information on lead free part marking, go to: http://www.linear.com/leadfree/ For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/ 24713fb 2 For more information www.linear.com/LTC2471 LTC2471/LTC2473 Electrical Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Note 2) PARAMETER CONDITIONS MIN TYP Resolution MAX UNITS 16 Integral Nonlinearity Output Rate 208sps (Note 4) Output Rate 833sps (Note 4) Offset Error l Offset Error Drift Bits 2 8 8.5 16 1 2.5 l l 0.05 LSB LSB mV LSB/C Gain Error l 0.01 Gain Error Drift l 0.15 LSB/C Transition Noise 3 VRMS Power Supply Rejection DC 80 dB Analog Inputs specifications are at TA = 25C. 0.25 % of FS The l denotes the specifications which apply over the full operating temperature range, otherwise SYMBOL PARAMETER CONDITIONS MAX UNITS VIN+ Positive Input Voltage Range LTC2473 l 0 VREF V VIN Negative Input Voltage Range LTC2473 l 0 VREF V VIN Input Voltage Range LTC2471 l 0 VOR+, VUR+ Overrange/Underrange Voltage, IN+ VIN- = 0.625V VOR-, VUR- Overrange/Underrange Voltage, IN- VIN+ = 0.625V CIN IN+, IN-, IN Sampling Capacitance IDC_LEAK(IN+, IN-, IN) IN+, IN- DC Leakage Current (LTC2473) ICONV Input Sampling Current (Notes 5, 8) VREF Reference Output Voltage - TYP VREF V 8 LSB 8 LSB 0.35 IN DC Leakage Current (LTC2471) Reference Voltage Coefficient MIN VIN = GND (Note 8) VIN = VCC (Note 8) l l -10 -10 1 1 pF 10 10 nA nA 50 l (Note 9) C-Grade I-Grade 1.247 l nA 1.25 1.253 2 5 10 V ppm/C ppm/C Reference Line Regulation 2.7V VCC 5.5V -90 dB Reference Short-Circuit Current VCC = 5.5, Forcing Output to GND (Note 8) l 35 mA COMP Pin Short-Circuit Current VCC = 5.5, Forcing Output to GND (Note 8) l 200 A Reference Load Regulation 2.7V VCC 5.5V, IOUT = 100A Sourcing 3.5 mV/mA Reference Output Noise Density CCOMP= 0.1F, CREFOUT = 0.1F, At f = 1ksps 30 nV/Hz Power Requirements The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. SYMBOL PARAMETER VCC Supply Voltage ICC Supply Current Conversion Conversion Nap Sleep CONDITIONS MIN l LTC2473 (Note 8) LTC2471 (Note 8) (Note 8) (Note 8) l l l l TYP 2.7 MAX 5.5 3.5 2.5 800 0.2 5 4 1500 2 UNITS V mA mA A A 24713fb For more information www.linear.com/LTC2471 3 LTC2471/LTC2473 I2C Inputs and Outputs The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Notes 2, 7) SYMBOL PARAMETER VIH High Level Input Voltage CONDITIONS l MIN VIL Low Level Input Voltage l II Digital Input Current (Note 8) l -10 0.05VCC TYP MAX UNITS 0.7VCC V 0.3VCC V 10 A VHYS Hysteresis of Schmidt Trigger Inputs (Note 3) l VOL Low Level Output Voltage (SDA) I = 3mA l 0.4 V V IIN Input Leakage 0.1VCC VIN 0.9VCC l 1 A CI Capacitance for Each I/O Pin l CB Capacitance Load for Each Bus Line l VIH(A0) High Level Input Voltage for Address Pin l VIL(A0) Low Level Input Voltage for Address Pin l 10 pF 400 pF 0.95VCC V 0.05VCC V I2C Timing Characteristics The l denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 25C. (Notes 2, 7) SYMBOL PARAMETER CONDITIONS TYP MAX tCONV1 Conversion Time SPD = 0 l MIN 4 4.8 UNITS ms tCONV2 Conversion Time SPD = 1 l 1 1.2 ms fSCL 400 kHz tHD(SDA,STA) SCL Clock Frequency l 0 Hold Time (Repeated) START Condition l 0.6 s tLOW LOW Period of the SCL Pin l 1.3 s tHIGH HIGH Period of the SCL Pin l 0.6 s tSU(STA) Set-Up Time for a Repeated START Condition l 0.6 s tHD(DAT) Data Hold Time l 0 0.9 s tSU(DAT) Data Set-Up Time l 100 tr Rise Time for SDA, SCL Signals (Note 6) l 20 + 0.1CB 300 ns ns tf Fall Time for SDA, SCL Signals (Note 6) l 20 + 0.1CB 300 ns tSU(STO) Set-Up Time for STOP Condition l 0.6 s tBUF Bus Free Time Between a STOP and START Condition l 1.3 s tOF Output Fall Time VIHMIN to VILMAX l 20 + 0.1CB tSP Input Spike Suppression Bus Load CB = 10pF to 400pF (Note 6) l Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime. Note 2. All voltage values are with respect to GND. VCC = 2.7V to 5.5V unless otherwise specified. VREFCM = VREF/2, FS = VREF, -VREF VIN VREF VIN = VIN+ - VIN -, VINCM = (VIN+ + VIN -)/2. (LTC2473) Note 3. Guaranteed by design, not subject to test. 250 ns 50 ns Note 4. Integral nonlinearity is defined as the deviation of a code from a straight line passing through the actual endpoints of the transfer curve. Note 5: Input sampling current is the average input current drawn from the input sampling network while the LTC2471/LTC2473 are converting. Note 6: CB = capacitance of one bus line in pF. Note 7: All values refer to VIH(MIN) and VIL(MAX) levels. Note 8: A positive current is flowing into the DUT pin. Note 9: Voltage temperature coefficient is calculated by dividing the maximum change in output voltage by the specified temperature range. 24713fb 4 For more information www.linear.com/LTC2471 LTC2471/LTC2473 Typical Performance Characteristics Integral Nonlinearity (TA = 25C, unless otherwise noted) Integral Nonlinearity 3 VCC = 2.7V TA = -45C, 25C, 90C 2 OUTPUT RATE = 208sps Maximum INL vs Temperature 3 6 2 4 1 2 OUTPUT RATE = 208sps INL (LSB) 0 -1 -2 -2 -2 VCC = 5.5V TA = -45C, 25C, 90C OUTPUT RATE = 208sps -3 0.25 0.75 -1.25 -0.75 -0.25 DIFFERENTIAL INPUT VOLTAGE (V) -4 -3 -1.25 0.25 0.75 -0.75 -0.25 DIFFERENTIAL INPUT VOLTAGE (V) 1.25 24713 G01 Offset Error vs Temperature ADC Gain Error vs Temperature VCC = 4.1V 15 10 VCC = 2.7V 0 -50 -30 50 -10 10 30 TEMPERATURE (C) 30 20 VCC = 4.1V 10 VCC = 2.7V -10 10 30 50 TEMPERATURE (C) 70 VCC = 5.5V 3.7 VCC = 4.1V 3.6 3.5 3.4 VCC = 2.7V 3.3 3.2 250 200 VCC = 4.1V 150 50 -10 10 30 TEMPERATURE (C) 70 90 100 24713 G07 0 -50 VCC = 2.7V -30 VCC = 5.5V 5 4 3 VCC = 2.7V 2 50 -10 10 30 TEMPERATURE (C) -30 24713 G05 VCC = 5.5V 50 3.1 -30 6 1.2508 300 SLEEP CURRENT (nA) 3.8 7 0 -50 90 350 3.9 24713 G03 8 Sleep Mode Power Supply Current vs Temperature 4.0 90 1 24713 G04 Conversion Mode Power Supply Current vs Temperature 3.0 -50 VCC = 5.5V -10 -50 -30 90 70 9 0 70 30 50 -10 10 TEMPERATURE (C) Transition Noise vs Temperature TRANSITION NOISE RMS (V) ADC GAIN ERROR (LSB) OFFSET ERROR (LSB) 20 -30 10 40 25 5 CONVERSION CURRENT (mA) -6 -50 1.25 50 VCC = 5.5V VCC = 2.7V 24713 G02 35 30 VCC = 4.1V 0 -1 REFERENCE OUTPUT VOLTAGE (V) INL (LSB) 0 INL (LSB) VCC = 5.5V 1 70 90 24713 G08 50 -10 10 30 TEMPERATURE (C) 70 90 24713 G06 VREF vs Temperature 1.2507 1.2506 1.2505 1.2504 1.2503 1.2502 -50 -30 50 -10 10 30 TEMPERATURE (C) 70 90 24713 G09 24713fb For more information www.linear.com/LTC2471 5 LTC2471/LTC2473 Typical Performance Characteristics Power Supply Rejection vs Frequency Applied to VCC Conversion Time vs Temperature 4.4 TA = 25C CONVERSION TIME (ms) REJECTION (dB) -40 -60 -80 -120 VCC = 2.7V 1 10 100 1k 10k 100k FREQUENCY AT VCC (Hz) 1M 10M 1.250335 4.2 1.250330 VCC = 4.1V 4.1 1.250325 1.250320 4.0 3.8 -50 1.250315 VCC = 5.5V 3.9 -100 TA = 25C 1.250340 4.3 -20 VREF vs VCC 1.250345 VREF (V) 0 (TA = 25C, unless otherwise noted) 1.250310 -25 25 50 0 TEMPERATURE (C) 24713 G010 75 100 24713 G11 1.250305 2.0 2.5 3.0 3.5 4.0 4.5 VCC (V) 5.0 5.5 6.0 24713 G12 Pin Functions REFOUT (Pin 1): Reference Output Pin. Nominally 1.25V, this voltage sets the full-scale input range of the ADC. For noise and reference stability connect to a 0.1F capacitor tied to GND. This capacitor value must be less than or equal to the capacitor tied to the reference compensation pin (COMP). REFOUT must not be overdriven by an external reference. COMP (Pin 2): Internal Reference Compensation Pin. For low noise and reference stability, tie a 0.1F capacitor to GND. A0 (Pin 3): Chip Address Control Pin. The A0 pin can be tied to GND or VCC. If A0 is tied to GND, the LTC2471/ LTC2473 I2C address is 0010100. If A0 is tied to VCC, the LTC2471/LTC2473 I2C address is 1010100. GND (Pins 4, 7, 11, (Exposed Pad Pin 13 - DFN Package Only)): Ground. Connect exposed pad directly to the ground plane through a low impedance connection. I 2C Interface. The SCL (Pin 5): Serial Clock Input of the LTC2471/LTC2473 can only act as an I2C slave and the SCL pin only accepts an external serial clock. Data is shifted into the SDA pin on the rising edges of SCL and output through the SDA pin on the falling edges of SCL. SDA (Pin 6): Bidirectional Serial Data Line of the I2C Interface. The conversion result is output through the SDA pin. The pin is high impedance unless the LTC2471/LTC2473 is in the data output mode. While the LTC2471/LTC2473 is in the data output mode, SDA is an open drain pull down (which requires an external 1.7k pull-up resistor to VCC). REF- (Pin 8): Negative Reference Input to the ADC. The voltage on this pin sets the zero input to the ADC. This pin should tie directly to ground or the ground sense of the input sensor. IN+ (LTC2473), IN (LTC2471) (Pin 9): Positive input voltage for the LTC2473 differential device. ADC input for the LTC2471 single-ended device. IN- (LTC2473), GND (LTC2471) (Pin 10): Negative input voltage for the LTC2473 differential device. GND for the LTC2471 single-ended device. VCC (Pin 12): Positive Supply Voltage. Bypass to GND with a 10F capacitor in parallel with a low-series-inductance 0.1F capacitor located as close to pin 12 as possible. 24713fb 6 For more information www.linear.com/LTC2471 LTC2471/LTC2473 Block Diagram 1 9 10 IN+ (IN) IN- (GND) 2 REFOUT COMP 12 AO INTERNAL REFERENCE A/D CONVERTER - VCC SPI INTERFACE DECIMATING SINC FILTER SCL SDA 3 5 6 A/D CONVERTER INTERNAL OSCILLATOR 8 REF- ( ) PARENTHESIS INDICATE LTC2471 4, 7, 11, 13 DD PACKAGE GND 4, 7, 11 MS PACKAGE 24713 BD Figure 1. Functional Block Diagram Applications Information Converter Operation POWER-ON RESET Converter Operation Cycle CONVERT The LTC2471/LTC2473 are low power, delta sigma, analog to digital converters with a simple I2C interface and a user selected 208sps/833sps output rate (see Figure 1). The LTC2473 has a fully differential input while the LTC2471 is single-ended. Both are pin and software compatible. Their operation is composed of three distinct states: CONVERT, SLEEP/NAP, and DATA INPUT/OUTPUT. The operation begins with the CONVERT state (see Figure 2). Once the conversion is finished, the converter automatically powers down (NAP) or under user control, both the converter and reference are powered down (SLEEP). The conversion result is held in a static register while the device is in this state. The cycle concludes with the DATA INPUT/OUTPUT state. Once all 16-bits are read or an abort is initiated, the device begins a new conversion. The CONVERT state duration is determined by the LTC2471/ LTC2473 conversion time (nominally 4.8ms or 1.2ms depending on the selected output rate). Once started, this operation can not be aborted except by a low power supply condition (VCC < 2.1V) which generates an internal power-on reset signal. SLEEP/NAP NO READ/WRITE ACKNOWLEDGE YES DATA INPUT/OUTPUT NO STOP OR READ 16 BITS YES 24713 F02 Figure 2. LTC2471/LTC2473 State Transition Diagram 24713fb For more information www.linear.com/LTC2471 7 LTC2471/LTC2473 applications information After the completion of a conversion, the LTC2471/LTC2473 enters the SLEEP/NAP state and remains there until a valid read/write is acknowledged. Following this condition, the ADC transitions into the DATA INPUT/OUTPUT state. While in the SLEEP/NAP state, the LTC2471/LTC2473's converters are powered down. This reduces the supply current by approximately 70%. While in the NAP state the reference remains powered up. The user can power down both the reference and the converter by enabling the sleep mode during the DATA INPUT/OUTPUT state. Once the next conversion is complete with the sleep mode enabled, the SLEEP state is entered and power is reduced to 2A (maximum). The reference is powered up once a valid read/write is acknowledged. The reference startup time is 12ms (if the reference and compensation capacitor values are both 0.1F). As the reference and compensation capacitors are decreased, the startup time is reduced (see Figure 3), but the transition noise increases (see Figure 4). Power-Up Sequence When the power supply voltage (VCC) applied to the converter is below approximately 2.1V, the ADC performs a power-on reset. This feature guarantees the integrity of the conversion result. When VCC rises above this critical threshold, the converter generates an internal power-on reset (POR) signal for approximately 0.5ms. For proper operation VDD needs to be restored to normal operating range (2.7V to 5.5V) before the conclusion of the POR cycle. The POR signal clears all internal registers. Following the POR signal, the LTC2471/ LTC2473 start a conversion cycle and follow the succession of states shown in Figure 2. The reference startup time following a POR is 12ms (CCOMP = CREFOUT = 0.1F). The first conversion following power-up will be invalid if the reference voltage has not completely settled (see Figure 3). The first conversion following power up can be discarded using the data abort command or simply read and ignored. Depending on the value chosen for CCOMP and CREFOUT, the reference startup can take more than one conversion period, see Figure 3. If the startup time is less than 1.2ms (833sps output rate) or 4.8ms (208sps output rate) then conversions following the first period are accurate to the device specifications. If the startup time exceeds 1.2ms or 4.8ms then the user can wait the appropriate time or use the fixed conversion period as a startup timer by ignoring results within the unsettled period. Once the reference has settled, all subsequent conversion results are valid. If the user places the device into the sleep mode (SLP = 1, reference powered down) the reference will require a startup time proportional to the value of CCOMP and CREFOUT (see Figure 3). 25 200 TRANSITION NOISE (V RMS) 250 VCC = 2.7V TIME (ms) 150 VCC = 4.1V 100 50 VCC = 5.5V 0 -50 1 0.1 0.01 CAPACITANCE (F) 0.001 20 15 10 5 0 0.0001 24713 F03 Figure 3. Reference Start-Up Time vs VREF and Compensation Capacitance 0.001 0.01 0.1 CAPACITANCE (F) 1 10 24713 F04 Figure 4. Transition Noise RMS vs COMP and Reference Capacitance 24713fb 8 For more information www.linear.com/LTC2471 LTC2471/LTC2473 Applications Information Ease of Use I2C INTERFACE The LTC2471/LTC2473 data output has no latency, filter settling delay, or redundant results associated with the conversion cycle. There is a one-to-one correspondence between the conversion and the output data. Therefore, multiplexing multiple analog input voltages requires no special actions. The LTC2471/LTC2473 communicate through an I2C interface. The I2C interface is a 2-wire open-drain interface supporting multiple devices and masters on a single bus. The connected devices can only pull the data line (SDA) LOW and can never drive it HIGH. SDA must be externally connected to the supply through a pull-up resistor. When the data line is free, it is HIGH. Data on the I2C bus can be transferred at rates up to 100kbits/s in the standard mode and up to 400kbits/s in the fast mode. The LTC2471/LTC2473 include a proprietary input sampling scheme that reduces the average input current by several orders of magnitude when compared to traditional deltasigma architectures. This allows external filter networks to interface directly to the LTC2471/LTC2473. Since the average input sampling current is 50nA, an external RC lowpass filter using 1k and 0.1F results in <1LSB additional error. Additionally, there is negligible leakage current between IN+ and IN- (for the LTC2473). Input Voltage Range (LTC2471) Ignoring offset and full-scale errors, the LTC2471 will theoretically output an "all zero" digital result when the input is at ground (a zero scale input) and an "all one" digital result when the input is at VREF or higher (VREFOUT = 1.25V). In an underrange condition (for all input voltages below zero scale) the converter will generate the output code 0. In an overrange condition (for all input voltages greater than VREF) the converter will generate the output code 65535. Input Voltage Range (LTC2473) As detailed in the Output Data Format section, the output code is given as INT(32767.5 * (VIN+ - VIN-)/VREF + 32767.5. For (VIN+ - VIN-) VREF, the output code is clamped at 65535 (all ones). For (VIN+ - VIN-) -VREF, the output code is clamped at 0 (all zeroes). Upon entering the DATA INPUT/OUTPUT state, SDA outputs the sign (D15) of the conversion result. During this state, the ADC shifts the conversion result serially through the SDA output pin under the control of the SCL input pin. There is no latency in generating this data and the result corresponds to the last completed conversion. A new bit of data appears at the SDA pin following each falling edge detected at the SCL input pin and appears from MSB to LSB. The user can reliably latch this data on every rising edge of the external serial clock signal driving the SCL pin. Each device on the I2C bus is recognized by a unique address stored in that device and can operate either as a transmitter or receiver, depending on the function of the device. In addition to transmitters and receivers, devices can also be considered as masters or slaves when performing data transfers. A master is the device which initiates a data transfer on the bus and generates the clock signals to permit that transfer. Devices addressed by the master are considered a slave. The address of the LTC2471/LTC2473 is 0010100 (if A0 is tied to GND) or 1010100 (if A0 is tied to VCC). 24713fb For more information www.linear.com/LTC2471 9 LTC2471/LTC2473 Applications Information The LTC2471/LTC2473 can only be addressed as a slave. It can only transmit the last conversion result. The serial clock line, SCL, is always an input to the LTC2471/LTC2473 and the serial data line SDA is bidirectional. Figure 5 shows the definition of the I2C timing. The START and STOP Conditions A START (S) condition is generated by transitioning SDA from HIGH to LOW while SCL is HIGH. The bus is considered to be busy after the START condition. When the data transfer is finished, a STOP (P) condition is generated by transitioning SDA from LOW to HIGH while SCL is HIGH. The bus is free after a STOP is generated. START and STOP conditions are always generated by the master. When the bus is in use, it stays busy if a repeated START (Sr) is generated instead of a STOP condition. The repeated START timing is functionally identical to the START and is used for reading from the device before the initiation of a new conversion. Data Transferring After the START condition, the I2C bus is busy and data transfer can begin between the master and the addressed slave. Data is transferred over the bus in groups of nine bits, one byte followed by one acknowledge (ACK) bit. The master releases the SDA line during the ninth SCL clock cycle. The slave device can issue an ACK by pulling SDA LOW or issue a Not Acknowledge (NACK) by leaving the SDA line HIGH impedance (the external pull-up resistor will hold the line HIGH). Change of data only occurs while the clock line (SCL) is LOW. Output Data Format After a START condition, the master sends a 7-bit address followed by a read request (R) bit. The bit R is 1 for a Read Request. If the 7-bit address matches the LTC2471/ LTC2473's address (0010100 or 1010100, depending on the state of the pin A0) the ADC is selected. When the device is addressed during the conversion state, it does SDA tf tLOW tSU(DAT) tr tf tHD(SDA) tSP tr tBUF SCL S tHD(STA) tHD(DAT) tHIGH tSU(STA) Sr tSU(STO) P S 24713 F05 Figure 5. Definition of Timing for Fast/Standard Mode Devices on the I2C Bus 24713fb 10 For more information www.linear.com/LTC2471 LTC2471/LTC2473 Applications Information not accept the request and issues a NACK by leaving the SDA line HIGH. If the conversion is complete, the LTC2471/ LTC2473 issue an ACK by pulling the SDA line LOW. Following the ACK, the LTC2471/LTC2473 can output data. The data output stream is 16 bits long and is shifted out on the falling edges of SCL (see Figure 6). The DATA INPUT/OUTPUT state is concluded once all 16 data bits have been read or after a STOP condition. The LTC2473 (differential input) output code is given by INT(32767.5 * (VIN+ - VIN-)/VREF + 32767.5. The first bit output by the LTC2473, D15, is the MSB, which is 1 for VIN+ VIN- and 0 for VIN+ < VIN-. This bit is followed by successively less significant bits (D14, D13, ...) until the LSB is output by the LTC2473, see Table 1. The LTC2471 (single-ended input) output code is a direct binary encoded result, see Table 1. Table 1. LTC2471/LTC2473 Output Data Format SINGLE ENDED INPUT VIN (LTC2471) DIFFERENTIAL INPUT VOLTAGE VIN+ - VIN- (LTC2473) D15 (MSB) D14 D13 D12...D2 D1 D0 (LSB) CORRESPONDING DECIMAL VALUE VREF VREF 1 1 1 1 1 1 65535 VREF - 1LSB VREF - 1LSB 1 1 1 1 1 0 65534 0.75 * VREF 0.5 * VREF 1 1 0 0 0 0 49152 0.75 * VREF - 1LSB 0.5 * VREF - 1LSB 1 0 1 1 1 1 49151 0.5 * VREF 0 1 0 0 0 0 0 32768 0.5 * VREF - 1LSB -1LSB 0 1 1 1 1 1 32767 0.25 * VREF -0.5 * VREF 0 1 0 0 0 0 16384 0.25 * VREF - 1LSB -0.5 * VREF - 1LSB 0 0 1 1 1 1 16383 0 -VREF 0 0 0 0 0 0 0 1 7 8 9 1 2 3 8 D15 D14 D13 D8 9 1 2 D7 D6 3 8 9 SCL SDA 7-BIT ADDRESS R MSB START BY MASTER SLEEP ACK BY LTC2471/LTC2473 D5 D0 LSB ACK BY MASTER DATA OUTPUT NACK BY MASTER CONVERSION 24713 F06 Figure 6. Read Sequence Timing Diagram 24713fb For more information www.linear.com/LTC2471 11 LTC2471/LTC2473 Applications Information The sleep bit (SLP) is used to power down the on chip reference. In the default mode, the reference remains powered up even when the ADC is powered down. If the SLP bit is set HIGH, the reference will power down after the next conversion is complete. It will remain powered down until a valid address is acknowledged. The reference startup time is approximately 12ms. In order to ensure a stable reference for the following conversions, either the data input/output time should be delayed 12ms after an address acknowledge or the first conversion following a reference start up should be discarded. Data Input Format After a START condition, the master sends a 7-bit address followed by a read/write request (R/W) bit. The R/W bit is 0 for a write. The data input word is 4 bits long and consists of two enable bits (EN1 and EN2) and two programming bits (SPD and SLP), see Figure 7. EN1 is applied to the first rising edge of SCL after a valid write address is acknowledged. Programming is enabled by setting EN1 = 1 and EN2 = 0. The speed bit (SPD) determines the output rate, SPD = 0 (default) for a 208sps and SPD = 1 for a 833sps output rate. The sleep bit (SLP) is used to power down the on-chip reference. In the default mode, the reference remains powered up at the conclusion of each conversion cycle while the ADC is automatically powered down at the end of each conversion cycle. If the SLP bit is set HIGH, the reference and the ADC are powered down once the next conversion cycle is completed. The reference and ADC are powered up again once a valid read/write is acknowledged. The following conversion is invalid if the next conversion is started before the reference has started up (see Figure 3 for reference startup times as a function of compensation capacitor and reference capacitor). 1 2 ... 7 8 9 Table 2. Input Data Format BIT NAME FUNCTION EN1 Should Be High (EN1 = 1) in Order to Enable Program Mode EN2 Should Be Low (EN2 = 0) in Order to Enable Program Mode SPD Low (SPD = 0, Default) for 208sps, High (SPD = 1) for 833sps Output Rate SLP Low (SLP = 0, Default) for Nap Mode, High (SLP = 1) for Sleep Mode Where Both Reference and Converter Are Powered Down 1 2 3 4 EN1 EN2 SPD SLP 5 6 7 8 9 SCL 7-BIT ADDRESS SDA W ACK BY LTC2471/LTC2473 START BY MASTER SLEEP ACK BY LTC2471/LTC2473 DATA INPUT 24713 F07 Figure 7. Timing Diagram for Writing to the LTC2471/LTC2473 24713fb 12 For more information www.linear.com/LTC2471 LTC2471/LTC2473 Applications Information OPERATION SEQUENCE signal indicating the conversion cycle is in progress. See Figure 9 for an example state diagram. Continuous Read Discarding a Conversion Result and Initiating a New Conversion Conversions from the LTC2471/LTC2473 can be continuously read, see Figure 8. The R/W is 1 for a read. At the end of a read operation, a new conversion automatically begins. At the conclusion of the conversion cycle, the next result may be read using the method described above. If the conversion cycle is not complete and a valid address selects the device, the LTC2471/LTC2473 generate a NACK S CONVERSION 7-BIT ADDRESS (0010100 OR 1010100) R ACK READ P DATA OUTPUT SLEEP It is possible to start a new conversion without reading the old result, as shown in Figure 10. Following a valid 7-bit address, a read request (R/W) bit, and a valid ACK, a STOP command will start a new conversion. S 7-BIT ADDRESS (0010100 OR 1010100) CONVERSION R ACK READ P DATA OUTPUT SLEEP CONVERSION 24713 F08 Figure 8. Consecutive Reading I2C START 7-BIT ADDRESS: 0010100 OR 1010100 R/W BIT LOW WRITE INPUT CONFIGURATION (FIGURE 7) ACK I2C STOP CONVERT CONVERSION FINISHED WRITE INPUT CONFIGURATION (FIGURE 7) FOR CYCLE N I2C (REPEAT) START R/W BIT LOW 7-BIT ADDRESS: 0010100 OR 1010100 I2C START CONVERSION FINISHED 7-BIT ADDRESS: 0010100 OR 1010100 R/W BIT HIGH ACK READ DATA FROM CYCLE N-1 NAK I2C STOP CONVERT 24713 F09 ACK Figure 9. I2C State Diagram S CONVERSION 7-BIT ADDRESS (0010100 OR 1010100) SLEEP R ACK READ (OPTIONAL) DATA OUTPUT P CONVERSION 24713 F10 Figure 10. Start a New Conversion without Reading Old Conversion Result 24713fb For more information www.linear.com/LTC2471 13 LTC2471/LTC2473 applications information PRESERVING THE CONVERTER ACCURACY The LTC2471/LTC2473 are designed to minimize the conversion result's sensitivity to device decoupling, PCB layout, anti-aliasing circuits, line and frequency perturbations. Nevertheless, in order to preserve the high accuracy capability of this part, some simple precautions are desirable. Digital Signal Levels Due to the nature of CMOS logic, it is advisable to keep input digital signals near GND or VCC. Voltages in the range of 0.5V to VCC - 0.5V may result in additional current leakage from the part. Undershoot and overshoot should also be minimized, particularly while the chip is converting. It is thus beneficial to keep edge rates of about 10ns and limit overshoot and undershoot to less than 0.3V. Driving VCC and GND In relation to the VCC and GND pins, the LTC2471/LTC2473 combines internal high frequency decoupling with damping elements, which reduce the ADC performance sensitivity to PCB layout and external components. Nevertheless, the very high accuracy of this converter is best preserved by careful low and high frequency power supply decoupling. A 0.1F, high quality, ceramic capacitor in parallel with a 10F low ESR ceramic capacitor should be connected between the VCC and GND pins, as close as possible to the package. The 0.1F capacitor should be placed closest to the ADC package. It is also desirable to avoid any via in the circuit path, starting from the converter VCC pin, passing through these two decoupling capacitors, and returning to the converter GND pin. The area encompassed by this circuit path, as well as the path length, should be minimized. As shown in Figure 11, REF- is used as the negative reference voltage input to the ADC. This pin can be tied directly to ground or Kelvin sensed to sensor ground. In the case where REF- is used as a sense input, it should be bypassed to ground with a 0.1F ceramic capacitor in parallel with a 10F low ESR ceramic capacitor. Very low impedance ground and power planes, and star connections at both VCC and GND pins, are preferable. The VCC pin should have two distinct connections: the first to the decoupling capacitors described above, and the second to the ground return for the power supply voltage source. REFOUT and COMP The on chip 1.25V reference is internally tied to the converter's reference input and is output to the REFOUT pin. A 0.1F capacitor should be placed on the REFOUT pin. It is possible to reduce this capacitor, but the transition noise increases (see Figure 4). A 0.1F capacitor should also be placed on the COMP pin. This pin is tied to an internal point in the reference and is used for stability. In order for the reference to remain stable, the capacitor placed on the COMP pin must be greater than or equal to the capacitor tied to the REFOUT pin. The REFOUT pin cannot be overridden by an external voltage. Depending on the size of the capacitors tied to the REFOUT and COMP pins, the internal reference has a corresponding start up time. This start up time is typically 12ms when 0.1F capacitors are used. The first conversion following power up can be discarded using the data abort comINTERNAL REFERENCE VCC ILEAK RSW 15k (TYP) REFOUT ILEAK IN (LTC2471) IN+ (LTC2473) VCC ILEAK ILEAK VCC IN- (LTC2473) RSW 15k (TYP) ILEAK CEQ 0.35pF (TYP) RSW 15k (TYP) ILEAK VCC ILEAK REF - RSW 15k (TYP) 24713 F11 ILEAK Figure 11. LTC2471/LTC2473 Analog Input/Reference Equivalent Circuit 24713fb 14 For more information www.linear.com/LTC2471 LTC2471/LTC2473 Applications Information mand or simply read and ignored. Depending on the value chosen for CCOMP and CREFOUT, the reference startup can take more than one conversion period, see Figure 3. If the startup time is less than 1.2ms (833sps output rate) or 4.8ms (208sps output rate) then conversions following the first period are accurate to the device specifications. If the startup time exceeds 1.2ms or 4.8ms then the user can wait the appropriate time or use the fixed conversion period as a startup timer by ignoring results within the unsettled period. Once the reference has settled all subsequent conversion results are valid. If the user places the device into the sleep mode (SLP = 1, reference powered down) the reference will require a startup time proportional to the value of CCOMP and CREFOUT, see Figure 3. If the reference is put to sleep (program SLP = 1 and CS = 1) the reference is powered down after the next conversion. This last conversion result is valid. On CS falling edge, the reference is powered back up. In order to ensure the reference output has settled before the next conversion, the power up time can be extended by delaying the data read after the falling edge of CS. Once all 16 bits are read from the device or CS is brought HIGH, the next conversion automatically begins. In the default operation, the reference remains powered up at the conclusion of the conversion cycle. converter equivalent internal resistor RSW and sampling capacitor CEQ. There are some immediate trade-offs in RS and CIN without needing a full circuit analysis. Increasing RS and CIN can give the following benefits: 1) Due to the LTC2471/LTC2473's input sampling algorithm, the input current drawn by either IN+ or IN- over a conversion cycle is typically 50nA. A high RS * CIN attenuates the high frequency components of the input current, and RS values up to 1k result in <1LSB error. 2) The bandwidth from VSIG is reduced at the input pins (IN+, IN- or IN). This bandwidth reduction isolates the ADC from high frequency signals, and as such provides simple anti-aliasing and input noise reduction. 3) Switching transients generated by the ADC are attenuated before they go back to the signal source. 4) A large CIN gives a better AC ground at the input pins, helping reduce reflections back to the signal source. 5) Increasing RS protects the ADC by limiting the current during an outside-the-rails fault condition. There is a limit to how large RS * CIN should be for a given application. Increasing RS beyond a given point increases Driving VIN+ and VIN- The input drive requirements can best be analyzed using the equivalent circuit of Figure 12. The input signal VSIG is connected to the ADC input pins (IN+ and IN-) through an equivalent source resistance RS. This resistor includes both the actual generator source resistance and any additional optional resistors connected to the input pins. Optional input capacitors CIN are also connected to the ADC input pins. This capacitor is placed in parallel with the input parasitic capacitance CPAR. This parasitic capacitance includes elements from the printed circuit board (PCB) and the associated input pin of the ADC. Depending on the PCB layout, CPAR has typical values between 2pF and 15pF. In addition, the equivalent circuit of Figure 12 includes the IN (LTC2471) RS SIG+ + - IN+ (LTC2473) CIN VCC ILEAK ILEAK CEQ 0.35pF (TYP) CPAR VCC RS SIG- + - IN- (LTC2473) CIN CPAR ILEAK ILEAK RSW 15k (TYP) ICONV RSW 15k (TYP) CEQ 0.35pF (TYP) ICONV 24713 F12 Figure 12. LTC2471/LTC2473 Input Drive Equivalent Circuit 24713fb For more information www.linear.com/LTC2471 15 LTC2471/LTC2473 applications information the voltage drop across RS due to the input current, to the point that significant measurement errors exist. Additionally, for some applications, increasing the RS * CIN product too much may unacceptably attenuate the signal at frequencies of interest. For most applications, it is desirable to implement CIN as a high-quality 0.1F ceramic capacitor and to set RS 1k. This capacitor should be located as close as possible to the actual IN+, IN- and IN package pins. Furthermore, the area encompassed by this circuit path, as well as the path length, should be minimized. In the case of a 2-wire sensor that is not remotely grounded, it is desirable to split RS and place series resistors in the ADC input line as well as in the sensor ground return line, which should be tied to the ADC GND pin using a star connection topology. Figure 13 shows the measured LTC2473 INL vs Input Voltage as a function of RS value with an input capacitor CIN = 0.1F. In some cases, RS can be increased above these guidelines. The input current is zero when the ADC is either in sleep or I/O modes. Thus, if the time constant of the input RC circuit t = RS * CIN, is of the same order of magnitude or longer than the time periods between actual conversions, then one can consider the input current to be reduced correspondingly. These considerations need to be balanced out by the input signal bandwidth. The 3dB bandwidth 1/(2pRSCIN). Finally, if the recommended choice for CIN is unacceptable for the user's specific application, an alternate strategy is to eliminate CIN and minimize CPAR and RS. In practical terms, this configuration corresponds to a low impedance sensor directly connected to the ADC through minimum length traces. Actual applications include current measurements through low value sense resistors, temperature measure- ments, low impedance voltage source monitoring, and so on. The resultant INL vs VIN is shown in Figure 14. The measurements of Figure 14 include a capacitor CPAR corresponding to a minimum sized layout pad and a minimum width input trace of about 1 inch length. Signal Bandwidth, Transition Noise and Noise Equivalent Input Bandwidth The LTC2471/LTC2473 include a sinc2 type digital filter. The first notch is located at 416Hz if the 208sps output rate is selected and 1666Hz if the 833sps output rate is selected. The calculated input signal attenuation vs. frequency over a wide frequency range is shown in Figure 15. The calculated input signal attenuation vs. frequency at low frequencies is shown in Figure 16. The converter noise level is about 3VRMS and can be modeled by a white noise source connected at the input of a noise-free converter. On a related note, the LTC2473 uses two separate A/D converters to digitize the positive and negative inputs. Each of these A/D converters has 3VRMS transition noise. If one of the input voltages is within this small transition noise band, then the output will fluctuate one bit, regardless of the value of the other input voltage. If both of the input voltages are within their transition noise bands, the output can fluctuate 2 bits. For a simple system noise analysis, the VIN drive circuit can be modeled as a single-pole equivalent circuit characterized by a pole location fi and a noise spectral density ni. If the converter has an unlimited bandwidth, or at least a bandwidth substantially larger than fi, then the total noise contribution of the external drive circuit would be: Vn = n i /2 * fi Then, the total system noise level can be estimated as the square root of the sum of (Vn2) and the square of the LTC2471/LTC2473 noise floor. 24713fb 16 For more information www.linear.com/LTC2471 LTC2471/LTC2473 applications information 6 4 3 RS = 1k 2 RS = 1k 2 CIN = 0 VCC = 5V TA = 25C 4 INL (LSB) INL (LSB) 6 CIN = 0.1F VCC = 5V TA = 25C 5 1 0 0 RS = 0k -2 -1 -2 RS = 0k -4 -3 -4 -1.25 0.25 0.75 -0.75 -0.25 DIFFERENTIAL INPUT VOLTAGE (V) -6 -1.25 1.25 0.25 0.75 -0.75 -0.25 DIFFERENTIAL INPUT VOLTAGE (V) 24713 F13 24713 F14 Figure 14. Measured INL vs Input Voltage 0 0 -20 -20 INPUT SIGNAL ATTENUATIOIN (dB) INPUT SIGNAL ATTENUATION (dB) Figure 13. Measured INL vs Input Voltage -40 -60 -80 -100 -40 -60 -80 -100 -120 -140 -120 0 5 10 20 15 -140 0 INPUT SIGNAL FREQUENCY (MHz) 1000 3000 4000 2000 INPUT SIGNAL FREQUENCY (Hz) 24713 F15 Figure 16. LTC2473 Input Signal Attenuation vs Frequency (208sps Mode) 0 0 -20 -20 -40 -60 -80 -100 5000 24713 F16 INPUT SIGNAL ATTENUATIOIN (dB) INPUT SIGNAL ATTENUATIOIN (dB) Figure 15. LTC2473 Input Signal Attenuation vs Frequency (208sps Mode) -40 -60 -80 -100 -120 -140 1.25 -120 0 5 15 10 INPUT SIGNAL FREQUENCY (MHz) 20 -140 0 24713 F17 Figure 17. LTC2473 Input Signal Attenuation vs Frequency (833sps Mode) 5 15 10 INPUT SIGNAL FREQUENCY (kHz) 20 24713 F18 Figure 18. LTC2473 Input Signal Attenuation vs Frequency (833sps Mode) 24713fb For more information www.linear.com/LTC2471 17 LTC2471/LTC2473 Package Description Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings. MS Package 12-Lead Plastic MSOP (Reference LTC DWG # 05-08-1668 Rev A) 4.039 0.102 (.159 .004) (NOTE 3) 0.889 0.127 (.035 .005) 5.10 (.201) MIN 0.406 0.076 (.016 .003) REF 12 11 10 9 8 7 3.20 - 3.45 (.126 - .136) 0.254 (.010) DETAIL "A" 3.00 0.102 (.118 .004) (NOTE 4) 4.90 0.152 (.193 .006) 0 - 6 TYP GAUGE PLANE 0.53 0.152 (.021 .006) 0.65 (.0256) BSC 0.42 0.038 (.0165 .0015) TYP DETAIL "A" 0.18 (.007) RECOMMENDED SOLDER PAD LAYOUT 1 2 3 4 5 6 1.10 (.043) MAX SEATING PLANE 0.22 - 0.38 (.009 - .015) TYP NOTE: 1. DIMENSIONS IN MILLIMETER/(INCH) 2. DRAWING NOT TO SCALE 3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS. INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE 5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX 0.86 (.034) REF 0.1016 0.0508 (.004 .002) 0.650 (.0256) BSC MSOP (MS12) 0213 REV A DD Package 12-Lead Plastic DFN (3mm x 3mm) (Reference LTC DWG # 05-08-1725 Rev A) R = 0.115 TYP 7 0.40 0.10 12 0.70 0.05 3.50 0.05 2.10 0.05 2.38 0.05 1.65 0.05 PACKAGE OUTLINE 3.00 0.10 (4 SIDES) 2.38 0.10 1.65 0.10 6 0.25 0.05 PIN 1 NOTCH R = 0.20 OR 0.25 x 45 CHAMFER PIN 1 TOP MARK (SEE NOTE 6) 0.45 BSC 0.200 REF 0.23 0.05 0.45 BSC 2.25 REF 2.25 REF RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS APPLY SOLDER MASK TO AREAS THAT ARE NOT SOLDERED 1 0.75 0.05 0.00 - 0.05 (DD12) DFN 0106 REV A BOTTOM VIEW--EXPOSED PAD NOTE: 1. DRAWING IS NOT A JEDEC PACKAGE OUTLINE 2. DRAWING NOT TO SCALE 3. ALL DIMENSIONS ARE IN MILLIMETERS 4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE 5. EXPOSED PAD AND TIE BARS SHALL BE SOLDER PLATED 6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION ON THE TOP AND BOTTOM OF PACKAGE 24713fb 18 For more information www.linear.com/LTC2471 LTC2471/LTC2473 Revision History REV DATE DESCRIPTION A 09/13 Clarified maximum operating output rate as 208sps/833sps. PAGE NUMBER B 03/14 Removed "No Missing Codes" resolution. Global 1, 3 24713fb Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. For more information www.linear.com/LTC2471 19 LTC2471/LTC2473 Typical Application 10F VCC 0.1F VCC 0.1F VCC 1 IN+ IN- 1k 1k 9 IN+ 12 REFOUT VCC 1.7k SCL VCC 1.7k 5 0.1F C 4 SCK/SCL 7 MOSI/SDA 5 MISO/SDO LTC2473 6 SDA IN- 3 10 A0 COMP REF- GND 0.1F 2 8 7, 11, 4 0.1F 0.1F 1F VCC GND 8 24713 TA02 Related Parts PART NUMBER DESCRIPTION COMMENTS LTC1860/LTC1861 12-Bit, 5V, 1-/2-Channel 250ksps SAR ADC in MSOP 850A at 250ksps, 2A at 1ksps, SO-8 and MSOP Packages LTC1860L/LTC1861L 12-Bit, 3V, 1-/2-Channel 150ksps SAR ADC 450A at 150ksps, 10A at 1ksps, SO-8 and MSOP Packages LTC1864/LTC1865 16-Bit, 5V, 1-/2-Channel 250ksps SAR ADC in MSOP 850A at 250ksps, 2A at 1ksps, SO-8 and MSOP Packages LTC1864L/LTC1865L 16-bit, 3V, 1-/2-Channel 150ksps SAR ADC 450A at 150ksps, 10A at 1ksps, SO-8 and MSOP Packages LTC2360 12-Bit, 100ksps SAR ADC 3V Supply, 1.5mW at 100ksps, TSOT 6-Pin/8-Pin Packages LTC2440 24-Bit No Latency TM ADC 200nVRMS Noise, 4kHz Output Rate, 15ppm INL LTC2480 16-Bit, Differential Input, No Latency ADC, with PGA, Temp. Sensor, SPI Easy DriveTM Input Current Cancellation, 600nVRMS Noise, Tiny 10-Lead DFN Package LTC2481 16-Bit, Differential Input, No Latency ADC, with PGA, Temp. Sensor, I2C Easy Drive Input Current Cancellation, 600nVRMS Noise, Tiny 10-Lead DFN Package LTC2482 16-Bit, Differential Input, No Latency ADC, SPI Easy Drive Input Current Cancellation, 600nVRMS Noise, Tiny 10-Lead DFN Package LTC2483 16-Bit, Differential Input, No Latency ADC, I2C Easy Drive Input Current Cancellation, 600nVRMS Noise, Tiny 10-Lead DFN Package LTC2484 24-Bit, Differential Input, No Latency ADC, SPI with Temp. Sensor Easy Drive Input Current Cancellation, 600nVRMS Noise, Tiny 10-Lead DFN Package LTC2485 24-Bit, Differential Input, No Latency ADC, I2C with Temp. Sensor Easy Drive Input Current Cancellation, 600nVRMS Noise, Tiny 10-Lead DFN Package LTC6241 Dual, 18MHz, Low Noise, Rail-to-Rail Op Amp 550nVP-P Noise, 125V Offset Max LTC2450 Easy-to-Use, Ultra-Tiny 16-Bit ADC, SPI, 0V to 5.5V Input Range 2 LSB INL, 50nA Sleep Current, Tiny 2mm x 2mm DFN-6 Package, 30Hz Output Rate LTC2450-1 Easy-to-Use, Ultra-Tiny 16-Bit ADC, SPI, 0V to 5.5V Input Range 2 LSB INL, 50nA Sleep Current, Tiny 2mm x 2mm DFN-6 Package, 60Hz Output Rate LTC2451 Easy-to-Use, Ultra-Tiny 16-Bit ADC, I2C, 0V to 5.5V Input Range 2 LSB INL, 50nA Sleep Current, Tiny 3mm x 2mm DFN-8 or TSOT Package, Programmable 30Hz/60Hz Output Rates LTC2452 Easy-to-Use, Ultra-Tiny 16-Bit Differential ADC, SPI, 5.5V Input Range 2 LSB INL, 50nA Sleep Current, Tiny 3mm x 2mm DFN-8 or TSOT Package LTC2453 Easy-to-Use, Ultra-Tiny 16-Bit Differential ADC, I2C, 5.5V Input Range 2 LSB INL, 50nA Sleep Current, Tiny 3mm x 2mm DFN-8 or TSOT Package LTC2460 Ultra-Tiny 16-Bit ADC with 10ppm Reference Pin and Software Compatible with LTC2471, 60Hz Output Rate LTC2462 Ultra-Tiny 16-Bit ADC with 10ppm Reference Pin and Software Compatible with LTC2473, 60Hz Output Rate 24713fb 20 Linear Technology Corporation 1630 McCarthy Blvd., Milpitas, CA 95035-7417 For more information www.linear.com/LTC2471 (408) 432-1900 FAX: (408) 434-0507 www.linear.com/LTC2471 LT 0314 REV B * PRINTED IN USA LINEAR TECHNOLOGY CORPORATION 2010