Non-Lighted and Lighted Rocker Switch _ Features m Unique leaf spring mechanism suppresses heat generation to improve safety during long power application Original forcible separation ensures positive contact separation, under severe conditions u Neon lamp allows switch to be directly applied with supply voltage mg Double-break contacts with gap of 3mm incorporated in nonflammabie housing m@ Abundant variations of rockers and flanges allowing selection of the type best suited to the equipment where mounted mw UL, CSA, and VDE approved WES See page 323 Ordering Information Classification Lighted (Neon lamps) Nonlighted 100 125 VAC 200 to 240 VAG Flange color White Black Gray White i Black Gray White Black Gray Lever color , White ABA-201 ABA-201-1 ABA-201-2 -_ oe -_ _ - Red ASA-202 ABA-202-1 ASA-202-2 ABA-212 ~ ABA-212-1 ABA-212-2 ABA-222 ASA-222-1 AGA-222-2 Green ABA-203 ABA-203-1 ABA-203-2 ABA-213 ABA-2139-1 = ABA-Z13-2. -AGA-223 ABA-223-1 ABA-229-2 Blue ABSA-204 ASA-204-1 AGA-204-2 ~ = _ - ~ Yellow ABA-205 ASA205-f ABA-205-2 - a _ _ = Orange _ - : ASA-216 A8A-216-1 ASBA-216-2 ABA-226 ABA-226-1 A8A-226-2 Black ABA-207 ABA-207-1 ABA-207-2 _ _ _ - _ - Specifications Contact ratings Item Noninductive Inductive load (A) load (A) Inrush Rated Resistive Lamp Inductive Motor current voltage : load load load load 125 VAC 6 ate] 16 16 400 A max. 250 VAC _ 16 10 8 16 Note: 1. The values in this table indicate the steady-state currents. 2. Inductive load has a power factor of 0.4 min. (AC) and a time constant of 7msec max. (DC). 3. Lamp load has an inrush current of 10 times the steady-state current, while motor load has an inrush current of 6 times the steady-state current. Neon lamp ratings Type Rated voltage (VAC} Set current (mA) A8A-2100 100 : 1.6 ABA-2200 - 220 1.5 Note: 1. The service life is 15,000 hours min. 2, LED lamps.are also avallable in red. Use part number ABA-252-1. 327Contact Form Lighted Non-lighted Characteristics (Data shown are of initial value) Operating speed 0.5 to 500 mm/sec . Mechanical: 30 operations/min. max. Operating frequency Electrical: 20 operations/min, max, insulation resistance 406 M& min. (at 500 VOC) Contact resistance 20 m@ max. BV/1A . Dielectric strength 2,000 VAC, 50/60 Hz for 1 minute between terminals of same polarity 2,000 VAC, 50/60 Hz for 1 minute between terminals of different polarity* and also between each terminal and ground Vibration Maltunction durability: 10 to &5 Hz; 1.5 mm double amplitude - Malfunction durability: 200 m/sec? (approx. 20Gs) Shock Mechanical durability: 500 m/sec? (approx. 50G's) Ambient temperatura Operating: -20 to +50C Humidity 45. to 85% AH Service life Mechanical: 40,000 operations min. Electrical: 20,000 operations min. Weight Non-lighted type: Approx. 15 g Lighted type: Approx. 16 g Note: f. The dielectric strength of the lighted type between terminals of different polarity is excluded. Dimensions [Unit: mm] : Operating characteristics 215-0. 2m OF max. 200 g FP 8+imm =< 30 +o4+ ; oP 541mm 1 1.7402 i, +04 FP: 841 wet CON 2279 4 { . #0 t " #250 Faston 30+1 | 10.8 | quick-connact terminal Jo 29.6403 > Note: 1. Recommended pane! thickness is 4.0 to 3.0 mm. ' 322Boer. atalog. Approved by Standards TAL @ ote that the rated values approved by each of the safety standards (e.g., UL, GSA) may be different from the performance characteristics individually defined in this Hints on Correct Use Mounting The A8A can be mounted.on a panel by one-touch. Mount the switch on the panel with the specified cutout dimen- sions and thickness. Do net usea - warped panel or one with a protruding seam. A mark (1.8-dia. depression) is provided on the case flange to indicate the ON side of the switch. Use this mark for reference when mounting the switch, Wiring The terminal Nos. 1 and 3 of the lighted type are at the primary side. The neon lamp of the lighted type illuminates when the switch is turned ON and extinguishes when it is turned OFF. 1-8-dia. depression ON side OFF side a 323