DS8838 DS8838 Quad Unified Bus Transceiver Literature Number: SNOSBL8A DS8838 Quad Unified Bus Transceiver General Description Features The DS8838 is a quad high speed driver/receiver designed for use in bus organized data transmission systems interconnected by terminated 120 impedance lines. The external termination is intended to be 180 resistor from the bus to the +5V logic supply together with a 390 resistor from the bus to ground. The bus can be terminated at one or both ends. Low bus pin current allows up to 27 driver/receiver pairs to utilize a common bus. The bus loading is unchanged when VCC = 0V. The receivers incorporate hysteresis to greatly enhance bus noise immunity. One two-input NOR gate is included to disable all drivers in a package simultaneously. Receiver performance is optimized for systems with bus rise and fall times 1.0 s/V. n n n n n n n n n 4 totally separate driver/receiver pairs per package 1V typical receiver input hysteresis Receiver hysteresis independent of receiver output load Guaranteed minimum bus noise immunity of 1.3V, 2V typ. Temperature-insensitive receiver thresholds track bus logic levels 20 A typical bus terminal current with normal VCC or with VCC = 0V Open collector driver output allows wire-OR connection High speed Series 74 TTL compatible driver and disable inputs and receiver outputs Typical Application DS005812-1 (c) 2001 National Semiconductor Corporation DS005812 www.national.com DS8838 Quad Unified Bus Receiver May 1999 DS8838 Connection Diagram Dual-In-Line Package DS005812-2 Top View Order Number DS7838J, DS8838M or DS8838N See NS Package Number J16A, M16A or N16A www.national.com 2 If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage Input and Output Voltage Storage Temperature Range Lead Temperature, (Soldering, 4 sec.) DS8838 Molded DIP Package: 1362 mW SO Package: 1002 mW Absolute Maximum Ratings (Note 2) Operating Conditions Operating Temperature Range Supply Voltage (VCC) 7V 5.5V -65C to +150C 260C 0C to +70C 4.75V VCC 5.25V Note 1: Derate cavity package 9.6 mW/C above 25C; derate molded DIP package 10.9 mW/C above 25C; derate SO package 8.01 mW/C above 25C. Maximum Power Dissipation (Note 1) at 25C Cavity Package: 1433 mW Electrical Characteristics The following apply for VMIN VCC VMAX, TMIN TA TMAX, unless otherwise specified (Notes 3, 4) Symbol Parameter Conditions Min Typ Max Units 0.8 V 1 mA DRIVER AND DISABLE INPUTS VIH Logical "1" Input Voltage VIL Logical "0" Input Voltage II Logical "1" Input Current VIN = 5.5V IIH Logical "1" Input Current VIN = 2.4V 40 A IIL Logical "0" Input Current VIN = 0.4V -1.6 mA VCL Input Diode Clamp Voltage IDIS = -12 mA, IIN = -12 mA, IBUS = -12 mA, TA = 25C -1 -1.5 V 2.0 V DRIVER OUTPUT/RECEIVER INPUT VOLB Low Level Bus Voltage VDIS = 0.8V, VIN = 2V, IBUS = 50 mA 0.4 0.7 V IIHB Maximum Bus Current VIN = 0.8V, VBUS = 4V, VCC = VMAX 20 100 A IILB Maximum Bus Current VIN = 0.8V, VBUS = 4V, VCC = 0V 2 100 A VIH High Level Receiver Threshold VIND = 0.8V, IOL = 16 mA, VCC = Max 1.80 2.25 2.50 V VIL Low Level Receiver Threshold VIND = 0.8V, VOH = -400 A, VCC = Min 1.05 1.30 1.55 V 2.4 0.25 0.4 V -55 mA RECEIVER OUTPUT VOH Logical "1" Output Voltage VIN = 0.8V, VBUS = 0.5V, IOH = -400 A VOL Logical "0" Output Voltage VIN = 0.8V, VBUS = 4V, IOL = 16 mA IOS Output Short Circuit Current VDIS = 0.8V, VIN = 0.8V, VBUS = 0.5V, VOS = 0V, VCC = VMAX, (Note 5) ICC Supply Current VDIS = 0V, VIN = 2V, (Per Package) 50 70 mA tpd Propagation Delays (Note 9) Disable to Bus "1" (Note 6) 19 30 ns Disable to Bus "0" (Note 6) 15 23 ns Driver Input to Bus "1" (Note 6) 17 25 ns Driver Input to Bus "0" (Note 6) 9 15 ns Bus to Logical "1" Receiver Output (Note 7) 20 30 ns Bus to Logical "0" Receiver Output (Note 8) 18 30 ns V -18 Note 2: "Absolute Maximum Ratings" are those values beyond which the safety of the device cannot be guaranteed. Except for "Operating Temperature Range" they are not meant to imply that the devices should be operated at these limits. The table of "Electrical Characteristics" provides conditions for actual device operation. Note 3: Unless otherwise specified min/max limits apply across the -55C to +125C temperature range for the DS7838 and across the 0C to +70C range for the DS8838. All typical values are for TA = 25C and VCC = 5V. Note 4: All currents into device pins shown as positive, out of device pins as negative, all voltages referenced to ground unless otherwise noted. All values shown as max or min on absolute value basis. Note 5: Only one output at a time should be shorted. Note 6: 91 from bus pin to VCC and 200 from bus pin to ground, CLOAD = 15 pF total. Measured from VIN = 1.5V to VBUS = 1.5V, VIN = 0V to 3.0V pulse. Note 7: Fan-out of 10 load, CLOAD = 15 pF total. Measured from VIN = 1.3V to VOUT = 1.5V, VIN = 0V to 3.0V pulse. Note 8: Fan-out of 10 load, CLOAD = 15 pF total. Measured from VIN = 2.3V to VOUT = 1.5V, VIN = 0V to 3.0V pulse. Note 9: These apply for VCC = 5V, TA = 25C unless otherwise speicified. 3 www.national.com DS8838 Physical Dimensions inches (millimeters) unless otherwise noted SO Package (M) Order Number DS8838M NS Package Number M16A Molded Dual-In-Line Package (N) Order Number DS8838N NS Package Number N16A www.national.com 4 DS8838 Quad Unified Bus Receiver Notes LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Email: support@nsc.com www.national.com National Semiconductor Europe Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Francais Tel: +33 (0) 1 41 91 8790 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: ap.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated