2SK851 - TOSHIBA - Pdf.Support

 2012-2017 Microchip Technology Inc. DS60001185G-page 1

PIC32MX330/350/370/430/450/470

Operating Conditions: 2.3V to 3.6V

• -40ºC to +105ºC (DC to 80 MHz)

• -40ºC to +85ºC (DC to 100 MHz)

• 0ºC to +70ºC (DC to 120 MHz)

Core: 120 MHz/150 DMIPS MIPS32® M4K®

• MIPS16e® mode for up to 40% smaller code size

• Code-efficient (C and Assembly) architecture

• Single-cycle (MAC) 32x16 and two-cycle 32x32 multiply

Clock Management

• 0.9% internal oscillator

• Programmable PLLs and oscillator clock sources

• Fail-Safe Clock Monitor (FSCM)

• Independent Watchdog Timer

• Fast wake-up and start-up

Power Management

• Low-power management modes (Sleep and Idle)

• Integrated Power-on Reset, Brown-out Reset, and High

Voltage Detect

• 0.5 mA/MHz dynamic current (typical)

• 50 A IPD current (typical)

Audio/Graphics/Touch HMI Features

• External graphics interface with up to 34 PMP pins

• Audio data communication: I2S, LJ, RJ, USB

• Audio data control interface: SPI and I2C

• Audio data master clock:

- Generation of fractional clock frequencies

- Can be synchronized with USB clock

- Can be tuned in run-time

• Charge Time Measurement Unit (CTMU):

- Supports mTouch™ capacitive touch sensing

- Provides high-resolution time measurement (1 ns)

Advanced Analog Features

• ADC Module:

- 10-bit 1 Msps rate with one Sample and Hold (S&H)

- Up to 28 analog inputs

- Can operate during Sleep mode

• Flexible and independent ADC trigger sources

• On-chip temperature measurement capability

• Comparators:

- Two dual-input Comparator modules

- Programmable references with 32 voltage points

Timers/Output Compare/Input Capture

• Five General Purpose Timers:

- Five 16-bit and up to two 32-bit Timers/Counters

• Five Output Compare (OC) modules

• Five Input Capture (IC) modules

• Peripheral Pin Select (PPS) to allow function remap

• Real-Time Clock and Calendar (RTCC) module

Communication Interfaces

• USB 2.0-compliant Full-speed OTG controller

• Up to five UART modules (20 Mbps):

- LIN 2.1 protocols and IrDA® support

• Two 4-wire SPI modules (25 Mbps)

• Two I2C modules (up to 1 Mbaud) with SMBus support

• PPS to allow function remap

• Parallel Master Port (PMP)

Direct Memory Access (DMA)

• Four channels of hardware DMA with automatic data

size detection

• 32-bit Programmable Cyclic Redundancy Check (CRC)

• Two additional channels dedicated to USB

Input/Output

• 15 mA or 12 mA source/sink for standard VOH/VOL and

up to 22 mA for non-standard VOH1

• 5V-tolerant pins

• Selectable open drain, pull-ups, and pull-downs

• External interrupts on all I/O pins

Qualification and Class B Support

• AEC-Q100 REVH (Grade 2 -40ºC to +105ºC) planned

• Class B Safety Library, IEC 60730

Debugger Development Support

• In-circuit and in-application programming

• 4-wire MIPS® Enhanced JTAG interface

• Unlimited program and six complex data breakpoints

• IEEE 1149.2-compatible (JTAG) boundary scan

Type QFN TQFP VTLA

Pin Count 64 64 100 100 124

I/O Pins (up to) 53 53 85 85 85

Contact/Lead Pitch 0.50 0.50 0.40 0.50 0.50

Dimensions 9x9x0.9 10x10x1 12x12x1 14x14x1 9x9x0.9

Note: All dimensions are in millimeters (mm) unless specified.

Packages

32-bit Microcontrollers (up to 512 KB Flash and 128 KB SRAM)

with Audio/Graphics/Touch (HMI), USB, and Advanced Analog

PIC32MX330/350/370/430/450/470

DS60001185G-page 2  2012-2017 Microchip Technology Inc.

TABLE 1: PIC32MX330/350/370/430/450/470 CONTROLLER FAMILY FEATURES

Device

Pins

Packages

Program Memory (KB)(1)

Data Memory (KB)

Remappable Peripherals

10-bit 1 Msps ADC (Channels)

Analog Comparators

USB On-The-Go (OTG)

CTMU

I2C

PMP

RTCC

DMA Channels

(Programmable/Dedicated)

I/O Pins

JTAG

Trace

Remappable Pins

Timers/Capture/Compare(2)

UART

SPI/I2S

External Interrupts(3)

PIC32MX330F064H 64 QFN,

TQFP 64+12 16 37 5/5/5 4 2/2 5 28 2 N Y 2 Y Y 4/0 53 Y N

PIC32MX330F064L 100 TQFP 64+12 16 54 5/5/5 5 2/2 5 28 2 N Y 2 Y Y 4/0 85 Y Y

124 VTLA

PIC32MX350F128H 64 QFN,

TQFP 128+12 32 37 5/5/5 4 2/2 5 28 2 N Y 2 Y Y 4/0 53 Y N

PIC32MX350F128L 100 TQFP 128+12 32 54 5/5/5 5 2/2 5 28 2 N Y 2 Y Y 4/0 85 Y Y

124 VTLA

PIC32MX350F256H 64 QFN,

TQFP 256+12 64 37 5/5/5 4 2/2 5 28 2 N Y 2 Y Y 4/0 53 Y N

PIC32MX350F256L 100 TQFP 256+12 64 54 5/5/5 5 2/2 5 28 2 N Y 2 Y Y 4/0 85 Y Y

124 VTLA

PIC32MX370F512H 64 QFN,

TQFP 512+12 128 37 5/5/5 4 2/2 5 28 2 N Y 2 Y Y 4/0 53 Y N

PIC32MX370F512L 100 TQFP 512+12 128 54 5/5/5 5 2/2 5 28 2 N Y 2 Y Y 4/0 85 Y Y

124 VTLA

PIC32MX430F064H 64 QFN,

TQFP 64+12 16 34 5/5/5 4 2/2 5 28 2 Y Y 2 Y Y 4/2 49 Y N

PIC32MX430F064L 100 TQFP 64+12 16 51 5/5/5 5 2/2 5 28 2 Y Y 2 Y Y 4/2 81 Y Y

124 VTLA

PIC32MX450F128H 64 QFN,

TQFP 128+12 32 34 5/5/5 4 2/2 5 28 2 Y Y 2 Y Y 4/2 49 Y N

PIC32MX450F128L 100 TQFP 128+12 32 51 5/5/5 5 2/2 5 28 2 Y Y 2 Y Y 4/2 81 Y Y

124 VTLA

PIC32MX450F256H 64 QFN,

TQFP 256+12 64 34 5/5/5 4 2/2 5 28 2 Y Y 2 Y Y 4/2 49 Y N

PIC32MX450F256L 100 TQFP 256+12 64 51 5/5/5 5 2/2 5 28 2 Y Y 2 Y Y 4/2 81 Y Y

124 VTLA

PIC32MX470F512H 64 QFN,

TQFP 512+12 128 34 5/5/5 4 2/2 5 28 2 Y Y 2 Y Y 4/2 49 Y N

PIC32MX470F512L 100 TQFP 512+12 128 51 5/5/5 5 2/2 5 28 2 Y Y 2 Y Y 4/2 81 Y Y

124 VTLA

Note 1: All devices feature 12 KB of Boot Flash memory.

2: Four out of five timers are remappable.

3: Four out of five external interrupts are remappable.

 2012-2017 Microchip Technology Inc. DS60001185G-page 3

PIC32MX330/350/370/430/450/470

Device Pin Tables

TABLE 2: PIN NAMES FOR 64-PIN DEVICES

Pin # Full Pin Name Pin # Full Pin Name

1AN22/RPE5/PMD5/RE5 33 RPF3/RF3

2 AN23/PMD6/RE6 34 RPF2/RF2

3AN27/PMD7/RE7 35 RPF6/SCK1/INT0/RF6

4 AN16/C1IND/RPG6/SCK2/PMA5/RG6 36 SDA1/RG3

5AN17/C1INC/RPG7/PMA4/RG7 37 SCL1/RG2

6 AN18/C2IND/RPG8/PMA3/RG8 38 VDD

7MCLR 39 OSC1/CLKI/RC12

8 AN19/C2INC/RPG9/PMA2/RG9 40 OSC2/CLKO/RC15

9 VSS 41 VSS

10 VDD 42 RPD8/RTCC/RD8

11 AN5/C1INA/RPB5/RB5 43 RPD9/RD9

12 AN4/C1INB/RB4 44 RPD10/PMCS2/RD10

13 PGED3/AN3/C2INA/RPB3/RB3 45 RPD11/PMCS1/RD11

14 PGEC3/AN2/C2INB/RPB2/CTED13/RB2 46 RPD0/RD0

15 PGEC1/VREF-/CVREF-/AN1/RPB1/CTED12/RB1 47 SOSCI/RPC13/RC13

16 PGED1/VREF+/CVREF+/AN0/RPB0/PMA6/RB0 48 SOSCO/RPC14/T1CK/RC14

17 PGEC2/AN6/RPB6/RB6 49 AN24/RPD1/RD1

18 PGED2/AN7/RPB7/CTED3//RB7 50 AN25/RPD2/RD2

19 AVDD 51 AN26/RPD3/RD3

20 AVSS 52 RPD4/PMWR/RD4

21 AN8/RPB8/CTED10//RB8 53 RPD5/PMRD/RD5

22 AN9/RPB9/CTED4/PMA7/RB9 54 RD6

23 TMS/CVREFOUT/AN10/RPB10/CTED11//PMA13/RB10 55 RD7

24 TDO/AN11/PMA12/RB11 56 VCAP

25 VSS 57 VDD

26 VDD 58 RPF0/RF0

27 TCK/AN12/PMA11/RB12 59 RPF1/RF1

28 TDI/AN13/PMA10/RB13 60 PMD0/RE0

29 AN14/RPB14/CTED5/PMA1/RB14 61 PMD1/RE1

30 AN15/RPB15/OCFB/CTED6/PMA0/RB15 62 AN20/PMD2/RE2

31 RPF4/SDA2/PMA9/RF4 63 RPE3/CTPLS/PMD3/RE3

32 RPF5/SCL2/PMA8/RF5 64 AN21/PMD4/RE4

Note 1: The RPn pins can be used by remappable peripherals. See Table 1 for the available peripherals and Section 12.3 “Peripheral Pin

Select” for restrictions.

2: Every I/O port pin (RBx-RGx), with the exception of RF6, can be used as a change notification pin (CNBx-CNGx). See Section 12.0 “I/O

Ports” for more information.

3: The metal plane at the bottom of the device is not connected to any pins and is recommended to be connected to VSS externally.

4: RPF6 (pin 35) is only available for output functions.

64-PIN QFN(1,2,3,4) AND TQFP(1,2,3,4) (TOP VIEW)

PIC32MX330F064H

PIC32MX350F128H

PIC32MX370F512H 64 1

QFN(4)

PIC32MX350F256H

TQFP

PIC32MX330/350/370/430/450/470

DS60001185G-page 4  2012-2017 Microchip Technology Inc.

TABLE 3: PIN NAMES FOR 64-PIN DEVICES

Pin # Full Pin Name Pin # Full Pin Name

1AN22/RPE5/PMD5/RE5 33 USBID/RF3

2 AN23/PMD6/RE6 34 VBUS

3AN27/PMD7/RE7 35 VUSB3V3

4 AN16/C1IND/RPG6/SCK2/PMA5/RG6 36 D-

5AN17/C1INC/RPG7/PMA4/RG7 37 D+

6 AN18/C2IND/RPG8/PMA3/RG8 38 VDD

7MCLR 39 OSC1/CLKI/RC12

8 AN19/C2INC/RPG9/PMA2/RG9 40 OSC2/CLKO/RC15

SS 41 VSS

10 VDD 42 RPD8/RTCC/RD8

11 AN5/C1INA/RPB5/VBUSON/RB5 43 RPD9/SDA1/RD9

12 AN4/C1INB/RB4 44 RPD10/SCL1/PMCS2/RD10

13 PGED3/AN3/C2INA/RPB3/RB3 45 RPD11/PMCS1/RD11

14 PGEC3/AN2/C2INB/RPB2/CTED13/RB2 46 RPD0/INT0/RD0

15 PGEC1/VREF-/CVREF-/AN1/RPB1/CTED12/RB1 47 SOSCI/RPC13/RC13

16 PGED1/VREF+/CVREF+/AN0/RPB0/PMA6/RB0 48 SOSCO/RPC14/T1CK/RC14

17 PGEC2/AN6/RPB6/RB6 49 AN24/RPD1/RD1

18 PGED2/AN7/RPB7/CTED3//RB7 50 AN25/RPD2/SCK1/RD2

19 AVDD 51 AN26/RPD3/RD3

20 AVSS 52 RPD4/PMWR/RD4

21 AN8/RPB8/CTED10//RB8 53 RPD5/PMRD/RD5

22 AN9/RPB9/CTED4/PMA7/RB9 54 RD6

23 TMS/CVREFOUT/AN10/RPB10/CTED11//PMA13/RB10 55 RD7

24 TDO/AN11/PMA12/RB11 56 VCAP

25 VSS 57 VDD

26 VDD 58 RPF0/RF0

27 TCK/AN12/PMA11/RB12 59 RPF1/RF1

28 TDI/AN13/PMA10/RB13 60 PMD0/RE0

29 AN14/RPB14/CTED5/PMA1/RB14 61 PMD1/RE1

30 AN15/RPB15/OCFB/CTED6/PMA0/RB15 62 AN20/PMD2/RE2

31 RPF4/SDA2/PMA9/RF4 63 RPE3/CTPLS/PMD3/RE3

32 RPF5/SCL2/PMA8/RF5 64 AN21/PMD4/RE4

Note 1: The RPn pins can be used by remappable peripherals. See Table 1 for the available peripherals and Section 12.3 “Peripheral Pin

Select” for restrictions.

2: Every I/O port pin (RBx-RGx) can be used as a change notification pin (CNBx-CNGx). See Section 12.0 “I/O Ports” for more informa-

tion.

3: The metal plane at the bottom of the device is not connected to any pins and is recommended to be connected to VSS externally.

64 1

QFN(3) 1

TQFP

64-PIN QFN(1,2) AND TQFP(1,2) (TOP VIEW)

PIC32MX430F064H

PIC32MX450F128H

PIC32MX470F512H

PIC32MX450F256H

 2012-2017 Microchip Technology Inc. DS60001185G-page 5

PIC32MX330/350/370/430/450/470

TABLE 4: PIN NAMES FOR 100-PIN DEVICES

Pin # Full Pin Name Pin # Full Pin Name

1RG15 36 VSS

2VDD 37 VDD

3AN22/RPE5/PMD5/RE5 38 TCK/CTED2/RA1

4 AN23/PMD6/RE6 39 RPF13/RF13

5AN27/PMD7/RE7 40 RPF12/RF12

6 RPC1/RC1 41 AN12/PMA11/RB12

7RPC2/RC2 42 AN13/PMA10/RB13

8 RPC3/RC3 43 AN14/RPB14/CTED5/PMA1/RB14

9 RPC4/CTED7/RC4 44 AN15/RPB15/OCFB/CTED6/PMA0/RB15

10 AN16/C1IND/RPG6/SCK2/PMA5/RG6 45 VSS

11 AN17/C1INC/RPG7/PMA4/RG7 46 VDD

12 AN18/C2IND/RPG8/PMA3/RG8 47 RPD14/RD14

13 MCLR 48 RPD15/RD15

14 AN19/C2INC/RPG9/PMA2/RG9 49 RPF4/PMA9/RF4

15 VSS 50 RPF5/PMA8/RF5

16 VDD 51 RPF3/RF3

17 TMS/CTED1/RA0 52 RPF2/RF2

18 RPE8/RE8 53 RPF8/RF8

19 RPE9/RE9 54 RPF7/RF7

20 AN5/C1INA/RPB5/RB5 55 RPF6/SCK1/INT0/RF6

21 AN4/C1INB/RB4 56 SDA1/RG3

22 PGED3/AN3/C2INA/RPB3/RB3 57 SCL1/RG2

23 PGEC3/AN2/C2INB/RPB2/CTED13/RB2 58 SCL2/RA2

24 PGEC1/AN1/RPB1/CTED12/RB1 59 SDA2/RA3

25 PGED1/AN0/RPB0/RB0 60 TDI/CTED9/RA4

26 PGEC2/AN6/RPB6/RB6 61 TDO/RA5

27 PGED2/AN7/RPB7/CTED3/RB7 62 VDD

28 VREF-/CVREF-/PMA7/RA9 63 OSC1/CLKI/RC12

29 VREF+/CVREF+/PMA6/RA10 64 OSC2/CLKO/RC15

30 AVDD 65 VSS

31 AVSS 66 RPA14/RA14

32 AN8/RPB8/CTED10/RB8 67 RPA15/RA15

33 AN9/RPB9/CTED4/RB9 68 RPD8/RTCC/RD8

34 CVREFOUT/AN10/RPB10/CTED11PMA13/RB10 69 RPD9/RD9

35 AN11/PMA12/RB11 70 RPD10/PMCS2/RD10

Note 1: The RPn pins can be used by remappable peripherals. See Table 1 for the available peripherals and Section 12.3 “Peripheral Pin

Select” for restrictions.

2: Every I/O port pin (RAx-RGx), with the exception of RF6, can be used as a change notification pin (CNAx-CNGx). See Section 12.0 “I/O

Ports” for more information.

3: RPF6 (pin 55) and RPF7 (pin 54) are only remappable for input functions.

100

100-PIN TQFP (TOP VIEW)(1,2,3)

PIC32MX330F064L

PIC32MX350F128L

PIC32MX370F512L

PIC32MX350F256L