03/29/2010
www.irf.com 1
HEXFET® Power MOSFET
S
D
G
GDS
Gate Drain Source
PD - 97483
AUIRF1324S
AUIRF1324L
D2Pak
AUIRF1324S
TO-262
AUIRF1324L
GD
S
GDS
Features
l
Advanced Process Technology
l
Ultra Low On-Resistance
l
Dynamic dV/dT Rating
l
175°C Operating Temperature
l
Fast Switching
l
Repetitive Avalanche Allowed up to Tjmax
l
Lead-Free, RoHS Compliant
l
Automotive Qualified *
Description
Specifically designed for Automotive applications, this HEXFET®
Power MOSFET utilizes the latest processing techniques to achieve
extremely low on-resistance per silicon area. Additional features of
this design are a 175°C junction operating temperature, fast switch-
ing speed and improved repetitive avalanche rating . These features
combine to make this design an extremely efficient and reliable
device for use in Automotive applications and a wide variety of other
applications.
HEXFET® is a registered trademark of International Rectifier.
*Qualification standards can be found at http://www.irf.com/
AUTOMOTIVE GRADE
V
DSS
24V
R
DS(on)
typ. 1.3mΩ
I
D
(Silicon Limited)
340A
c
I
D
(Package Limited)
195A
Absolute Maximum Ratings
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only; and
functional operation of the device at these or any other condition beyond those indicated in the specifications is not implied. Exposure to absolute-
maximum-rated conditions for extended periods may affect device reliability. The thermal resistance and power dissipation ratings are measured under
board mounted and still air conditions. Ambient temperature (TA) is 25°C, unless otherwise specified.
Symbol Parameter Units
I
D
@ T
C
= 25°C Continuous Drain Current, VGS @ 10V (Silicon Limited)
I
D
@ T
C
= 100°C Continuous Drain Current, V
GS
@ 10V (Silicon Limited)
I
D
@ T
C
= 25°C Continuous Drain Current, V
GS
@ 10V (Package Limited)
I
DM
Pulsed Drain Current
d
P
D
@T
C
= 25°C Maximum Power Dissipation W
Linear Derating Factor W/°C
V
GS
Gate-to-Source Voltage V
E
AS
Single Pulse Avalanche Energy (Thermally Limited)
e
mJ
I
AR
Avalanche Current
d
A
E
AR
Repetitive Avalanche Energy
d
mJ
dv/dt Peak Diode Recovery
f
V/ns
T
J
Operating Junction and
T
STG
Storage Temperature Range
Soldering Temperature, for 10 seconds
(1.6mm from case)
Thermal Resistance
Symbol Parameter Typ. Max. Units
R
θJC
Junction-to-Case
k
––– 0.50 °C/W
R
θJA
Junction-to-Ambient (PCB Mounted, steady-state)
j
––– 40
Max.
340
240
1420
195 A
°C
300
-55 to + 175
± 20
2.0
270
See Fig. 14, 15, 22a, 22b
300
0.46
AUIRF1324S/L
2www.irf.com
Notes:
Calculated continuous current based on maximum allowable junction
temperature. Bond wire current limit is 195A. Note that current
limitations arising from heating of the device leads may occur with
some lead mounting arrangements. (Refer to AN-1140).
Repetitive rating; pulse width limited by max. junction
temperature.
Limited by TJmax, starting TJ = 25°C, L = 0.014mH
RG = 25Ω, IAS = 195A, VGS =10V. Part not recommended for use
above this value.
S
D
G
ISD ≤ 195A, di/dt ≤ 450A/µs, VDD ≤ V(BR)DSS, TJ ≤ 175°C.
Pulse width ≤ 400µs; duty cycle ≤ 2%.
Coss eff. (TR) is a fixed capacitance that gives the same charging time
as Coss while VDS is rising from 0 to 80% VDSS.
Coss eff. (ER) is a fixed capacitance that gives the same energy as
Coss while VDS is rising from 0 to 80% VDSS.
When mounted on 1" square PCB (FR-4 or G-10 Material). For recom-
mended footprint and soldering techniques refer to application note #AN-994.
Rθ is measured at TJ approximately 90°C.
Static Electrical Characteristics @ T
J
= 25°C (unless otherwise specified)
Symbol Parameter Min. Typ. Max. Units
V
(BR)DSS
Drain-to-Source Breakdown Voltage 24 ––– ––– V
∆V
(
BR
)
DSS
/∆T
J
Breakdown Voltage Temp. Coefficient ––– 22 ––– mV/°C
R
DS(on)
Static Drain-to-Source On-Resistance ––– 1.3 1.65 mΩ
V
GS(th)
Gate Threshold Voltage 2.0 ––– 4.0 V
gfs Forward Transconductance 180 ––– ––– S
R
G
Internal Gate Resistance ––– 2.3 ––– Ω
I
DSS
Drain-to-Source Leakage Current ––– ––– 20 µA
––– ––– 250
I
GSS
Gate-to-Source Forward Leakage ––– ––– 200 nA
Gate-to-Source Reverse Leakage ––– ––– -200
Dynamic Electrical Characteristics @ T
J
= 25°C (unless otherwise specified)
Symbol Parameter Min. Typ. Max. Units
Q
g
Total Gate Charge ––– 160 240 nC
Q
gs
Gate-to-Source Charge ––– 84 –––
Q
gd
Gate-to-Drain ("Miller") Charge ––– 49 –––
Q
sync
Total Gate Charge Sync. (Q
g
- Q
gd
)––– 76 –––
t
d(on)
Turn-On Delay Time ––– 17 ––– ns
t
r
Rise Time ––– 190 –––
t
d(off)
Turn-Off Delay Time ––– 83 –––
t
f
Fall Time ––– 120 –––
C
iss
Input Capacitance ––– 7590 ––– pF
C
oss
Output Capacitance ––– 3440 –––
C
rss
Reverse Transfer Capacitance ––– 1960 –––
C
oss
eff. (ER) Effective Output Capacitance (Ener
g
y Related) ––– 4700 –––
C
oss
eff. (TR) Effective Output Capacitance (Time Related) ––– 4490 –––
Diode Characteristics
Symbol Parameter Min. Typ. Max. Units
I
S
Continuous Source Current ––– ––– 350
c
A
(Body Diode)
I
SM
Pulsed Source Current ––– ––– 1420 A
(Body Diode)
d
V
SD
Diode Forward Voltage ––– ––– 1.3 V
t
rr
Reverse Recovery Time ––– 46 ––– ns T
J
= 25°C V
R
= 20V,
––– 71 ––– T
J
= 125°C I
F
= 195A
Q
rr
Reverse Recovery Charge ––– 160 ––– nC T
J
= 25°C di/dt = 100A/µs
g
––– 430 ––– T
J
= 125°C
I
RRM
Reverse Recovery Current ––– 7.7 ––– A T
J
= 25°C
t
on
Forward Turn-On Time Intrinsic turn-on time is negligible (turn-on is dominated by LS+LD)
V
DS
= 10V, I
D
= 195A
I
D
= 195A
R
G
= 2.7Ω
V
GS
= 10V
g
V
DD
= 16V
I
D
= 195A, V
DS
=0V, V
GS
= 10V
Conditions
I
D
= 195A
V
GS
= 20V
V
GS
= -20V
T
J
= 25°C, I
S
= 195A, V
GS
= 0V
g
integral reverse
p-n junction diode.
Conditions
V
GS
= 0V, I
D
= 250µA
Reference to 25°C, I
D
= 5.0mA
d
V
GS
= 10V, I
D
= 195A
g
V
DS
= V
GS
, I
D
= 250µA
V
DS
= 24V, V
GS
= 0V
V
DS
= 24V, V
GS
= 0V, T
J
= 125°C
MOSFET symbol
showing the
V
DS
= 12V
Conditions
V
GS
= 10V
g
V
GS
= 0V
V
DS
= 24V
ƒ = 1.0 MHz, See Fig. 5
V
GS
= 0V, V
DS
= 0V to 19V
i
, See Fig. 11
V
GS
= 0V, V
DS
= 0V to 19V
h
AUIRF1324S/L
www.irf.com 3
Qualification standards can be found at International Rectifiers web site: http//www.irf.com/
 Exceptions to AEC-Q101 requirements are noted in the qualification report.
Qualification Information
†
D2Pak MSL1
TO-262 N/A
Qualification Level
Automotive
(per AEC-Q101)
††
Comments: This part number(s) passed Automotive qualification.
IR’s Industrial and Consumer qualification level is granted by
extension of the higher Automotive level.
Charged Device Model Class C5
AEC-Q101-005
Moisture Sensitivity Level
RoHS Compliant Yes
ESD
Machine Model Class M4
AEC-Q101-002
Human Body Model Class H3A
AEC-Q101-001
AUIRF1324S/L
4www.irf.com
Fig 1. Typical Output Characteristics
Fig 3. Typical Transfer Characteristics Fig 4. Normalized On-Resistance vs. Temperature
Fig 2. Typical Output Characteristics
Fig 6. Typical Gate Charge vs. Gate-to-Source VoltageFig 5. Typical Capacitance vs. Drain-to-Source Voltage
2 3 4 5 6 7 8 9
VGS, Gate-to-Source Voltage (V)
0.1
1
10
100
1000
ID, Drain-to-Source Current (A)
TJ = 25°C
TJ = 175°C
VDS = 15V
≤60µs PULSE WIDTH
-60 -40 -20 020 40 60 80 100120140160180
TJ , Junction Temperature (°C)
0.5
1.0
1.5
2.0
RDS(on) , Drain-to-Source On Resistance
(Normalized)
ID = 195A
VGS = 10V
110 100
VDS, Drain-to-Source Voltage (V)
1000
10000
100000
C, Capacitance (pF)
VGS = 0V, f = 1 MHZ
Ciss = C gs + Cgd, C ds SHORTED
Crss = Cgd
Coss = Cds + Cgd
Coss
Crss
Ciss
0 50 100 150 200
QG, Total Gate Charge (nC)
0.0
2.0
4.0
6.0
8.0
10.0
12.0
14.0
VGS, Gate-to-Source Voltage (V)
VDS= 19V
VDS= 12V
ID= 195A
0.1 110 100
VDS, Drain-to-Source Voltage (V)
10
100
1000
10000
ID, Drain-to-Source Current (A)
4.0V
≤60µs PULSE WIDTH
Tj = 175°C
VGS
TOP 15V
10V
8.0V
6.0V
5.5V
5.0V
4.5V
BOTTOM 4.0V
0.1 110 100
VDS, Drain-to-Source Voltage (V)
0.1
1
10
100
1000
10000
ID, Drain-to-Source Current (A)
VGS
TOP 15V
10V
8.0V
6.0V
5.5V
5.0V
4.5V
BOTTOM 4.0V
≤60µs PULSE WIDTH
Tj = 25°C
4.0V
AUIRF1324S/L
www.irf.com 5
Fig 8. Maximum Safe Operating Area
Fig 10. Drain-to-Source Breakdown Voltage
Fig 7. Typical Source-Drain Diode
Forward Voltage
Fig 11. Typical COSS Stored Energy
Fig 9. Maximum Drain Current vs.
Case Temperature
Fig 12. Maximum Avalanche Energy vs. DrainCurrent
0.0 0.5 1.0 1.5
VSD, Source-to-Drain Voltage (V)
1.0
10
100
1000
ISD, Reverse Drain Current (A)
TJ = 25°C
TJ = 175°C
VGS = 0V
-60 -40 -20 020 40 60 80 100120140160180
TJ , Temperature ( °C )
24
26
28
30
32
V(BR)DSS, Drain-to-Source Breakdown Voltage (V)
Id = 5mA
-5 0 5 10 15 20 25 30
VDS, Drain-to-Source Voltage (V)
0.0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
Energy (µJ)
25 50 75 100 125 150 175
TC , Case Temperature (°C)
0
50
100
150
200
250
300
350
ID, Drain Current (A)
Limited By Package
1 10 100
VDS, Drain-to-Source Voltage (V)
1
10
100
1000
10000
ID, Drain-to-Source Current (A)
OPERATION IN THIS AREA
LIMITED BY R DS(on)
Tc = 25°C
Tj = 175°C
Single Pulse
100µsec
1msec
10msec
DC
Limited by
package
25 50 75 100 125 150 175
Starting TJ , Junction Temperature (°C)
0
200
400
600
800
1000
1200
EAS , Single Pulse Avalanche Energy (mJ)
ID
TOP 44A
83A
BOTTOM 195A
AUIRF1324S/L
6www.irf.com
Fig 13. Maximum Effective Transient Thermal Impedance, Junction-to-Case
Fig 14. Typical Avalanche Current vs.Pulsewidth
1.0E-06 1.0E-05 1.0E-04 1.0E-03 1.0E-02 1.0E-01
tav (sec)
1
10
100
1000
Avalanche Current (A)
0.05
Duty Cycle = Single Pulse
0.10
Allowed avalanche Current vs avalanche
pulsewidth, tav, assuming ∆Τ j = 25°C and
Tstart = 150°C.
0.01
Allowed avalanche Current vs avalanche
pulsewidth, tav, assuming ∆Tj = 150°C and
Tstart =25°C (Single Pulse)
1E-006 1E-005 0.0001 0.001 0.01 0.1
t1 , Rectangular Pulse Duration (sec)
0.001
0.01
0.1
1
Thermal Response ( Z thJC ) °C/W
0.20
0.10
D = 0.50
0.02
0.01
0.05
SINGLE PULSE
( THERMAL RESPONSE )
Notes:
1. Duty Factor D = t1/t2
2. Peak Tj = P dm x Zthjc + Tc
τJ
τJ
τ1
τ1
τ2
τ2τ3
τ3
R1
R1R2
R2R3
R3
Ci i/Ri
Ci= τi/Ri
τ
τC
τ4
τ4
R4
R4Ri (°C/W) τi (sec)
0.0125 0.000008
0.0822 0.000078
0.2019 0.001110
0.2036 0.007197
AUIRF1324S/L
www.irf.com 7
Fig 16. Threshold Voltage vs. Temperature
-75 -50 -25 025 50 75 100 125 150 175 200
TJ , Temperature ( °C )
1.0
1.5
2.0
2.5
3.0
3.5
4.0
4.5
VGS(th), Gate threshold Voltage (V)
ID = 250µA
ID = 1.0mA
ID = 1.0A
Fig 15. Maximum Avalanche Energy vs. Temperature
Notes on Repetitive Avalanche Curves , Figures 14, 15:
(For further info, see AN-1005 at www.irf.com)
1. Avalanche failures assumption:
Purely a thermal phenomenon and failure occurs at a temperature far in
excess of Tjmax. This is validated for every part type.
2. Safe operation in Avalanche is allowed as long asTjmax is not exceeded.
3. Equation below based on circuit and waveforms shown in Figures 16a, 16b.
4. PD (ave) = Average power dissipation per single avalanche pulse.
5. BV = Rated breakdown voltage (1.3 factor accounts for voltage increase
during avalanche).
6. Iav = Allowable avalanche current.
7. ∆T = Allowable rise in junction temperature, not to exceed Tjmax (assumed as
25°C in Figure 14, 15).
tav = Average time in avalanche.
D = Duty cycle in avalanche = tav ·f
ZthJC(D, tav) = Transient thermal resistance, see Figures 13)
PD (ave) = 1/2 ( 1.3·BV·Iav) = DT/ ZthJC
Iav = 2DT/ [1.3·BV·Zth]
EAS (AR) = PD (ave)·tav
25 50 75 100 125 150 175
Starting TJ , Junction Temperature (°C)
0
50
100
150
200
250
300
EAR , Avalanche Energy (mJ)
TOP Single Pulse
BOTTOM 1.0% Duty Cycle
ID = 195A
AUIRF1324S/L
8www.irf.com
Fig 23a. Switching Time Test Circuit Fig 23b. Switching Time Waveforms
Fig 22b. Unclamped Inductive Waveforms
Fig 22a. Unclamped Inductive Test Circuit
tp
V
(BR)DSS
I
AS
R
G
I
AS
0.01
Ω
t
p
D.U.T
L
VDS
+
-V
DD
DRIVER
A
15V
20V
VGS
Fig 24a. Gate Charge Test Circuit Fig 24b. Gate Charge Waveform
Vds
Vgs
Id
Vgs(th)
Qgs1 Qgs2 Qgd Qgodr
Fig 21. Peak Diode Recovery dv/dt Test Circuit for N-Channel
HEXFET® Power MOSFETs
Circuit Layout Considerations
• Low Stray Inductance
• Ground Plane
• Low Leakage Inductance
Current Transformer
P.W. Period
di/dt
Diode Recovery
dv/dt
Ripple ≤5%
Body Diode Forward Drop
Re-Applied
Voltage
Reverse
Recovery
Current
Body Diode Forward
Current
V
GS
=10V
V
DD
I
SD
Driver Gate Drive
D.U.T. I
SD
Waveform
D.U.T. V
DS
Waveform
Inductor Curent
D = P. W .
Period
* VGS = 5V for Logic Level Devices
*
+
-
+
+
+
-
-
-
RGVDD
• dv/dt controlled by RG
• Driver same type as D.U.T.
• ISD controlled by Duty Factor "D"
• D.U.T. - Device Under Test
D.U.T
Inductor Current
D.U.T. VDS
ID
IG
3mA
VGS
.3µF
50KΩ
.2µF
12V
Current Regulator
Same Type as D.U.T.
Current Sampling Resistors
+
-
VDS
90%
10%
VGS
t
d(on)
t
r
t
d(off)
t
f
VDS
Pulse Width ≤ 1 µs
Duty Factor ≤ 0.1 %
RD
VGS
RG
D.U.T.
10V
+
-
VDD
VGS
AUIRF1324S/L
www.irf.com 9
D2Pak (TO-263AB) Package Outline
Dimensions are shown in millimeters (inches)
D2Pak (TO-263AB) Part Marking Information
Note: For the most current drawing please refer to IR website at http://www.irf.com/package/
AUIRF1324S
YWWA
XX or XX
Date Code
Y= Year
WW= Work Week
A= Automotive, LeadFree
Part Number
IR Logo
Lot Code
AUIRF1324S/L
10 www.irf.com
TO-262 Package Outline
Dimensions are shown in millimeters (inches)
TO-262 Part Marking Information
Note: For the most current drawing please refer to IR website at http://www.irf.com/package/
AUIRF1324L
YWWA
XX or XX
Date Code
Y= Year
WW= Work Week
A= Automotive, LeadFree
Part Number
IR Logo
Lot Code
AUIRF1324S/L
www.irf.com 11
D2Pak (TO-263AB) Tape & Reel Information
Dimensions are shown in millimeters (inches)
3
4
4
TRR
FEED DIRECTION
1.85 (.073)
1.65 (.065)
1.60 (.063)
1.50 (.059)
4.10 (.161)
3.90 (.153)
TRL
FEED DIRECTION
10.90 (.429)
10.70 (.421)
16.10 (.634)
15.90 (.626)
1.75 (.069)
1.25 (.049)
11.60 (.457)
11.40 (.449) 15.42 (.609)
15.22 (.601)
4.72 (.136)
4.52 (.178)
24.30 (.957)
23.90 (.941)
0.368 (.0145)
0.342 (.0135)
1.60 (.063)
1.50 (.059)
13.50 (.532)
12.80 (.504)
330.00
(14.173)
MAX.
27.40 (1.079)
23.90 (.941)
60.00 (2.362)
MIN.
30.40 (1.197)
MAX.
26.40 (1.039)
24.40 (.961)
NOTES :
1. COMFORMS TO EIA-418.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION MEASURED @ HUB.
4. INCLUDES FLANGE DISTORTION @ OUTER EDGE.
AUIRF1324S/L
12 www.irf.com
Ordering Information
Base
p
art Packa
g
e T
yp
e Standard Pack Com
lete Part Number
Form Quantit
y
AUIRF1324S D2Pak Tube 50 AUIRF1324S
Ta
p
e and Reel Left 800 AUIRF1324STRL
Ta
p
e and Reel Ri
g
ht 800 AUIRF1324STRR
AUIRF1324L TO-262 Tube 50 AUIRF1324L
AUIRF1324S/L
www.irf.com 13
For
IMPORTANT NOTICE
Unless specifically designated for the automotive market, International Rectifier Corporation and its subsidiaries (IR) reserve the right
to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to
discontinue any product or services without notice. Part numbers designated with the “AU” prefix follow automotive industry and / or
customer specific requirements with regards to product discontinuance and process change notification. All products are sold subject to
IR’s terms and conditions of sale supplied at the time of order acknowledgment.
IR warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with IR’s standard
warranty. Testing and other quality control techniques are used to the extent IR deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
IR assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using IR components. To minimize the risks with customer products and applications, customers should provide adequate
design and operating safeguards.
Reproduction of IR information in IR data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alterations is an unfair and
deceptive business practice. IR is not responsible or liable for such altered documentation. Information of third parties may be subject
to additional restrictions.
Resale of IR products or serviced with statements different from or beyond the parameters stated by IR for that product or service voids
all express and any implied warranties for the associated IR product or service and is an unfair and deceptive business practice. IR is
not responsible or liable for any such statements.
IR products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or
in other applications intended to support or sustain life, or in any other application in which the failure of the IR product could create a
situation where personal injury or death may occur. Should Buyer purchase or use IR products for any such unintended or unauthorized
application, Buyer shall indemnify and hold International Rectifier and its officers, employees, subsidiaries, affiliates, and distributors
harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim
of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that IR was negligent regarding
the design or manufacture of the product.
IR products are neither designed nor intended for use in military/aerospace applications or environments unless the IR products are
specifically designated by IR as military-grade or “enhanced plastic.” Only products designated by IR as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of IR products which IR has not designated as military-grade is solely
at the Buyer’s risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such
use.
IR products are neither designed nor intended for use in automotive applications or environments unless the specific IR products are
designated by IR as compliant with ISO/TS 16949 requirements and bear a part number including the designation “AU”. Buyers
acknowledge and agree that, if they use any non-designated products in automotive applications, IR will not be responsible for any failure
to meet such requirements.
For technical support, please contact IR’s Technical
Assistance Center
http://www.irf.com/technical-info/
WORLD HEADQUARTERS:
233 Kansas St., El Segundo, California 90245
Tel: (310) 252-7105