B43201F2128M000 - EPCOS AG

Data Sheet

Aluminum electrolytic capacitors

Alu-X product lines

4-pin snap-in capacitors

Series/Type: B41201, B43201

Date: April 2008

mation contained therein without EPCOS’ prior express consent is prohibited.

AEC-C_B41201_B43201.book Seite 1 Mittwoch, 16. April 2008 2:14 14

204/08

Please read Cautions and warnings and

Important notes at the end of this document.

General-purpose grade capacitors

Applications

■Professional switch-mode power supplies

Features

■High ripple current capability

■RoHS-compatible

■Load life of 2000 h at 85 °C

Construction

■Aluminum case, fully insulated

■Charge/discharge-proof

■Minus pole marking on the insulating sleeve

■Case with safety vent

4-pin snap-in capacitors B41201, B43201

Standard series – 85 °C

AEC-C_B41201_B43201.book Seite 2 Mittwoch, 16. April 2008 2:14 14

4-pin snap-in capacitors B41201, B43201

Standard series – 85 °C

304/08

Please read Cautions and warnings and

Important notes at the end of this document.

Specifications and characteristics in brief

Rated voltage VR10 … 500 V DC

Operating tempera-

ture range

VR ≤ 250 V DC: –40 °C … +85 °C

VR ≥ 315 V DC: –25 °C … +85 °C

Rated capacitance CR

(20 °C, 120 Hz)

100 … 68000 µF

Capacitance tolerance ±20% M

Load life

(85 °C, VR, IAC,R)

2000 h Requirements:

∆C/C ≤ ±20% of initial value

tan δ≤ 2 times initial specified limit

Ileak ≤ initial specified limit

Leakage current Ileak

(20 °C, after 5 minutes)

Dissipation factor

(max.)

(20 °C, 120 Hz)

(V DC)

10 16 25 35 50 63 80 100 160 ...

200

250 ...

400

450 ...

500

tan δ0.50 0.50 0.40 0.40 0.30 0.25 0.20 0.15 0.12 0.15 0.20

Low temperature sta-

bility (impedance ratio)

(120 Hz)

VR (V DC) 10 16 ... 160 200 ... 250 315 ... 400 450 ... 500

5478 8

18 15 12 ––

Shelf life After storage for 1000 h at 85 °C, the capacitors shall meet the requirement

of load life test after reforming process. After test: VR to be applied for

30 minutes, 24 to 48 hours before measurement.

Frequency multiplier

for rated ripple current

50 Hz 120 Hz 1 kHz 10 kHz 20 kHz

≤50 V 0.95 1.00 1.10 1.15 1.15

63 ... 100 V 0.95 1.00 1.16 1.30 1.33

≥160 V 0.90 1.00 1.20 1.50 1.55

Temperature multiplier

for rated ripple current

+40 °C +55 °C +70 °C +85 °C

<160 V 2.1 2.1 1.5 1.0

≥160 V 1.7 1.5 1.3 1.0

Ileak 0.02 µA CR

µF

------- VR

-------

⋅

⎝⎠

⎛⎞

⋅≤

Z 25 °C–()

Z +20 °C()

---------------------------

Z40 °C–()

Z +20 °C()

---------------------------

AEC-C_B41201_B43201.book Seite 3 Mittwoch, 16. April 2008 2:14 14

4-pin snap-in capacitors B41201, B43201

Standard series – 85 °C

404/08

Please read Cautions and warnings and

Important notes at the end of this document.

Dimensional drawing

Overview of available types B41201

(V DC) 10 16 25 35

Case dimensions d × l (mm)

CR (µF)

12000 35 × 30

15000 35 × 35

18000 35 × 40

22000 35 × 30 35 × 45

27000 35 × 25 35 × 35

33000 35 × 25 35 × 30 35 × 40

39000 35 × 30 35 × 35 35 × 45

47000 35 × 30 35 × 40

56000 35 × 35 35 × 45

68000 35 × 40 35 × 50

KAL1136-W-E

Plus pole marking

d+1

Mounting holes

22.5±0.1

2±0.1

l+2

6.0±1

0.8

1.5±0.2

Minus pole marking

on the case wall

Safety vent

0.8+0.2

0.1

30 ±30’

AEC-C_B41201_B43201.book Seite 4 Mittwoch, 16. April 2008 2:14 14

4-pin snap-in capacitors B41201, B43201

Standard series – 85 °C

504/08

Please read Cautions and warnings and

Important notes at the end of this document.

Overview of available types B41201

(V DC) 50 63 80 100

Case dimensions d × l (mm)

CR (µF)

2700 35 × 30

3300 35 × 35

3900 35 × 35

4700 35 × 25 35 × 30 35 × 30 35 × 40

5600 35 × 25 35 × 30 35 × 35 35 × 45

6800 35 × 30 35 × 30 35 × 40

8200 35 × 30 35 × 35 35 × 45

10000 35 × 35 35 × 40

12000 35 × 40 35 × 45

15000 35 × 45

18000 35 × 50

Overview of available types B43201

(V DC) 160 200 250 315

Case dimensions d × l (mm)

CR (µF)

180 35 × 20

220 35 × 20

270 35 × 25

330 35 × 20 35 × 30

390 35 × 20 35 × 20 35 × 30

470 35 × 20 35 × 25 35 × 35

560 35 × 20 35 × 20 35 × 25 35 × 40

680 35 × 20 35 × 25 35 × 30 35 × 45

820 35 × 25 35 × 30 35 × 35 35 × 50

1000 35 × 25 35 × 30 35 × 40

1200 35 × 30 35 × 35 35 × 45

1500 35 × 35 35 × 40 35 × 50

1800 35 × 40 35 × 45

AEC-C_B41201_B43201.book Seite 5 Mittwoch, 16. April 2008 2:14 14

4-pin snap-in capacitors B41201, B43201

Standard series – 85 °C

604/08

Please read Cautions and warnings and

Important notes at the end of this document.

Overview of available types B43201

(V DC) 350 400 450 500

Case dimensions d × l (mm)

CR (µF)

100 35 × 20

120 35 × 20

150 35 × 20 35 × 25

180 35 × 20 35 × 25 35 × 25

220 35 × 35 35 × 25 35 × 30

270 35 × 25 35 × 30 35 × 35 35 × 45

330 35 × 30 35 × 30 35 × 40 35 × 50

390 35 × 35 35 × 35 35 × 45

470 35 × 40 35 × 40 35 × 50

560 35 × 45 35 × 45

680 35 × 50

AEC-C_B41201_B43201.book Seite 6 Mittwoch, 16. April 2008 2:14 14

4-pin snap-in capacitors B41201, B43201

Standard series – 85 °C

704/08

Please read Cautions and warnings and

Important notes at the end of this document.

Technical data and ordering codes B41201

V DC

120 Hz

20 °C

µF

Case

dimensions

d × l

IAC,R

120 Hz

85 °C

Ordering code

10 33000 35 × 25 5.81 B41201D3339M000

39000 35 × 30 6.38 B41201C3399M000

47000 35 × 30 6.62 B41201C3479M000

56000 35 × 35 7.18 B41201B3569M000

68000 35 × 40 7.76 B41201A3689M000

16 27000 35 × 25 5.80 B41201C4279M000

33000 35 × 30 6.41 B41201B4339M000

39000 35 × 35 6.96 B41201B4399M000

47000 35 × 40 7.54 B41201B4479M000

56000 35 × 45 8.08 B41201A4569M000

68000 35 × 50 8.63 B41201A4689M000

25 22000 35 × 30 5.51 B41201B5229M000

27000 35 × 35 6.12 B41201B5279M000

33000 35 × 40 6.74 B41201B5339M000

39000 35 × 45 7.35 B41201A5399M000

35 12000 35 × 30 5.24 B41201B7129M000

15000 35 × 35 5.88 B41201B7159M000

18000 35 × 40 6.46 B41201B7189M000

22000 35 × 45 7.07 B41201A7229M000

50 4700 35 × 25 4.19 B41201D6478M000

5600 35 × 25 4.44 B41201D6568M000

6800 35 × 30 5.04 B41201D6688M000

8200 35 × 30 5.26 B41201C6828M000

10000 35 × 35 5.97 B41201B6109M000

12000 35 × 40 6.55 B41201B6129M000

15000 35 × 45 7.20 B41201A6159M000

18000 35 × 50 7.74 B41201A6189M000

63 4700 35 × 30 4.19 B41201D8478M000

5600 35 × 30 4.70 B41201C8568M000

6800 35 × 30 5.04 B41201C8688M000

8200 35 × 35 5.53 B41201B8828M000

10000 35 × 40 6.25 B41201B8109M000

12000 35 × 45 6.83 B41201A8129M000

AEC-C_B41201_B43201.book Seite 7 Mittwoch, 16. April 2008 2:14 14

4-pin snap-in capacitors B41201, B43201

Standard series – 85 °C

804/08

Please read Cautions and warnings and

Important notes at the end of this document.

80 4700 35 × 30 5.27 B41201C0478M000

5600 35 × 35 5.81 B41201B0568M000

6800 35 × 40 5.46 B41201A0688M000

8200 35 × 45 6.91 B41201A0828M000

100 2700 35 × 30 4.37 B41201C9278M000

3300 35 × 35 4.85 B41201C9338M000

3900 35 × 35 5.27 B41201B9398M000

4700 35 × 40 5.80 B41201B9478M000

5600 35 × 45 6.34 B41201A9568M000

Technical data and ordering codes B41201

V DC

120 Hz

20 °C

µF

Case

dimensions

d × l

IAC,R

120 Hz

85 °C

Ordering code

AEC-C_B41201_B43201.book Seite 8 Mittwoch, 16. April 2008 2:14 14

4-pin snap-in capacitors B41201, B43201

Standard series – 85 °C

904/08

Please read Cautions and warnings and

Important notes at the end of this document.

Technical data and ordering codes B43201

V DC

120 Hz

20 °C

µF

Case

dimensions

d × l

IAC,R

120 Hz

85 °C

Ordering code

160 560 35 × 20 2.12 B43201D1567M000

680 35 × 20 2.33 B43201D1687M000

820 35 × 25 2.73 B43201D1827M000

1000 35 × 25 3.01 B43201D1108M000

1200 35 × 30 3.26 B43201C1128M000

1500 35 × 35 3.83 B43201B1158M000

1800 35 × 40 4.39 B43201A1188M000

200 390 35 × 20 1.77 B43201D2397M000

470 35 × 20 1.94 B43201D2477M000

560 35 × 20 2.25 B43201D2567M000

680 35 × 25 2.48 B43201D2687M000

820 35 × 30 2.88 B43201D2827M000

1000 35 × 30 3.18 B43201B2108M000

1200 35 × 35 3.43 B43201B2128M000

1500 35 × 40 4.01 B43201B2158M000

1800 35 × 45 4.58 B43201A2188M000

250 330 35 × 20 1.62 B43201I2337M000

390 35 × 20 1.77 B43201I2397M000

470 35 × 25 2.06 B43201I2477M000

560 35 × 25 2.25 B43201I2567M000

680 35 × 30 2.62 B43201H2687M000

820 35 × 35 3.03 B43201G2827M000

1000 35 × 40 3.50 B43201G2108M000

1200 35 × 45 3.74 B43201F2128M000

1500 35 × 50 4.35 B43201F2158M000

315 180 35 × 20 1.20 B43201D0187M000

220 35 × 20 1.33 B43201D0227M000

270 35 × 25 1.56 B43201D0277M000

330 35 × 30 1.83 B43201D0337M000

390 35 × 30 1.99 B43201C0397M000

470 35 × 35 2.29 B43201B0477M000

560 35 × 40 2.62 B43201A0567M000

680 35 × 45 3.01 B43201A0687M000

820 35 × 50 3.44 B43201A0827M000

AEC-C_B41201_B43201.book Seite 9 Mittwoch, 16. April 2008 2:14 14

4-pin snap-in capacitors B41201, B43201

Standard series – 85 °C

10 04/08

Please read Cautions and warnings and

Important notes at the end of this document.

350 180 35 × 20 1.20 B43201D4187M000

220 35 × 35 1.41 B43201D4227M000

270 35 × 25 1.65 B43201C4277M000

330 35 × 30 1.83 B43201C4337M000

390 35 × 35 2.09 B43201B4397M000

470 35 × 40 2.40 B43201B4477M000

560 35 × 45 2.73 B43201A4567M000

680 35 × 50 3.13 B43201A4687M000

400 150 35 × 20 1.09 B43201D9157M000

180 35 × 25 1.28 B43201D9187M000

220 35 × 25 1.41 B43201D9227M000

270 35 × 30 1.65 B43201C9277M000

330 35 × 30 1.83 B43201C9337M000

390 35 × 35 2.09 B43201B9397M000

470 35 × 40 2.40 B43201B9477M000

560 35 × 45 2.73 B43201A9567M000

450 100 35 × 20 0.68 B43201D5107M000

120 35 × 20 0.75 B43201D5127M000

150 35 × 25 0.89 B43201D5157M000

180 35 × 25 0.98 B43201C5187M000

220 35 × 30 1.14 B43201C5227M000

270 35 × 35 1.33 B43201B5277M000

330 35 × 40 1.54 B43201B5337M000

390 35 × 45 1.74 B43201A5397M000

470 35 × 50 1.99 B43201A5477M000

500 270 35 × 45 1.45 B43201A6277M000

330 35 × 50 1.66 B43201A6337M000

Technical data and ordering codes B43201

V DC

120 Hz

20 °C

µF

Case

dimensions

d × l

IAC,R

120 Hz

85 °C

Ordering code

AEC-C_B41201_B43201.book Seite 10 Mittwoch, 16. April 2008 2:14 14

11 04/08

Please read Cautions and warnings and

Important notes at the end of this document.

General

Also see “Important notes” on page 13.

1 Aluminum electrolytic capacitors have a bi-polar structure. This is marked on the body of the

capacitor. A capacitor must not be mounted with reversed polarity. The application of an AC

or reverse voltage may cause a short circuit or damage the capacitor. Bi-polar capacitors

must not be used in AC applications, where the polarity may be reversed in the circuits or is

unknown.

2 The DC voltage applied to the capacitor terminal must not exceed its rated operating voltage,

as this will result in a rapid increase of the leakage current and may damage the capacitor. It

is recommended to operate the capacitor at 70–80% of its rated voltage to optimize its serv-

ice life.

3 The ripple current applied to the capacitor must be within the permitted range. An excessive

ripple current leads to impaired electrical properties and may damage the capacitor. Note that

the sum of the peak values of the ripple voltage and the DC operating voltage must not ex-

ceed the rated DC voltage.

4 Capacitors must be used within their permitted range of operating temperature. Operation at

room temperature optimizes their service life.

5 Capacitors with case diameter ≥8 mm are equipped with a safety vent. In capacitors fitted

with a lead or soldering lug, the safety vent is usually located at the base of the case. It needs

sufficient space around it to operate optimally. The following dimensions are recommended:

for case diameter d = 8 to 16 mm, more than 2 mm; for d =18 to 35 mm, more than 3 mm;

and for d = 42 mm or more, more than 5 mm.

6 Capacitors should not be mounted with the safety vent face down on the board. Do not locate

any wire or copper trace near the safety vent. Do not reverse the voltage, as this may result

in excess pressure and the leakage of electrolyte.

7 Gas is released through the safety vent when the pressure inside the capacitor is too high. A

gaseous liquid around the safety vent does not indicate a leakage of electrolyte.

8 The capacitor should be stored under conditions of normal temperature and in a non-acid,

non-alkali environment of normal humidity. Exposure to high temperatures, for example un-

der direct sunlight, will reduce its operating life. If the capacitor is stored in an environment

containing acids or alkalis, the solderability of the leads may be affected.

9 The leakage current of an aluminum electrolytic capacitor may increase after a long period

of storage. After such storage, the capacitor must be aged by applying the rated operating

voltage for 6–8 hours before use.

10 Manual soldering:

a Soldering must be performed within the specified conditions.

Bit temperature: 350 °C; application time of soldering iron: 3 seconds.

b Ensure that the soldering iron does not touch any part of the capacitor body.

Cautions and warnings

AEC-C_B41201_B43201.book Seite 11 Mittwoch, 16. April 2008 2:14 14

Cautions and warnings

12 04/08

Please read Cautions and warnings and

Important notes at the end of this document.

11 Do not apply excessive force to the leads and terminals. Do not move the capacitor after sol-

dering it onto the PC board and do not carry the PC board by gripping the capacitor. Observe

the following rules to prevent undue stress to the capacitor:

a Do not tilt or bend the capacitor after soldering.

b Ensure that the terminal spacing matches the corresponding hole spacing on the PC

board.

12 The aluminum case is not insulated from the cathode. Do not place a conductor under the

aluminum capacitors on the PC board as this may cause a short circuit. The case and top of

capacitors used in switched mode power supplies have a high-voltage-resistant heat shrink

sleeve to ensure safe usage.

13 The leads of capacitors with a case diameter exceeding 14 mm cannot be used for fixing.

AEC-C_B41201_B43201.book Seite 12 Mittwoch, 16. April 2008 2:14 14

Important notes

13 04/08

Important notes

The following applies to all products named in this publication:

1. Some parts of this publication contain statements about the suitability of our products for

certain areas of application. These statements are based on our knowledge of typical

requirements that are often placed on our products in the areas of application concerned. We

nevertheless expressly point out that such statements cannot be regarded as binding

statements about the suitability of our products for a particular customer application. As

a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them

than the customers themselves. For these reasons, it is always ultimately incumbent on the

customer to check and decide whether an EPCOS product with the properties described in the

product specification is suitable for use in a particular customer application.

2. We also point out that in individual cases, a malfunction of electronic components or failure

before the end of their usual service life cannot be completely ruled out in the current state

of the art, even if they are operated as specified. In customer applications requiring a very

high level of operational safety and especially in customer applications in which the malfunction

or failure of an electronic component could endanger human life or health (e.g. in accident

prevention or life-saving systems), it must therefore be ensured by means of suitable design of

the customer application or other action taken by the customer (e.g. installation of protective

circuitry or redundancy) that no injury or damage is sustained by third parties in the event of

malfunction or failure of an electronic component.

3. The warnings, cautions and product-specific notes must be observed.

4. In order to satisfy certain technical requirements, some of the products described in this

publication may contain substances subject to restrictions in certain jurisdictions (e.g.

because they are classed as hazardous). Useful information on this will be found in our

Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more

detailed questions, please contact our sales offices.

5. We constantly strive to improve our products. Consequently, the products described in this

publication may change from time to time. The same is true of the corresponding product

specifications. Please check therefore to what extent product descriptions and specifications

contained in this publication are still applicable before or when you place an order.

We also reserve the right to discontinue production and delivery of products. Consequently,

we cannot guarantee that all products named in this publication will always be available. The

aforementioned does not apply in case of individual agreements deviating from the foregoing for

customer-specific products.

6. Unless otherwise agreed in individual contracts, all orders are subject to the current version

of the “General Terms of Delivery for Products and Services in the Electrical Industry”

published by the German Electrical and Electronics Industry Association (ZVEI).

7. The trade names EPCOS, BAOKE, Alu-X, CeraDiode, CSSP, CTVS, DSSP, MiniBlue, MKK,

MLSC, MotorCap, PCC, PhaseCap, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap,

SIMDAD, SIMID, SineFormer, SIOV, SIP5D, SIP5K, ThermoFuse, WindCap are trademarks

registered or pending in Europe and in other countries. Further information will be found on

the Internet at www.epcos.com/trademarks.