Precision, 500 ns Settling BiFET Op Amp AD744 Data Sheet FEATURES AC PERFORMANCE 500 ns Settling to 0.01% for 10 V Step 1.5 s Settling to 0.0025% for 10 V Step 75 V/s Slew Rate 0.0003% Total Harmonic Distortion (THD) 13 MHz Gain Bandwidth - Internal Compensation >200 MHz Gain Bandwidth (G = 1000) External Decompensation >1000 pF Capacitive Load Drive Capability with 10 V/s Slew Rate - External Compensation DC PERFORMANCE 0.5 mV max Offset Voltage (AD744B) 10 V/C max Drift (AD744B) 250 V/mV min Open-Loop Gain (AD744B) Available in Plastic Mini-DIP, Plastic SOIC, Hermetic Cerdip, Hermetic Metal Can Packages and Chip Form Surface Mount (SOIC) Package Available in Tape and Reel in Accordance with EIA-481A Standard CONNECTION DIAGRAMS TO-99 (H) Package 8-Lead Plastic Mini-DIP (N) 8-Lead SOIC (R) Package and 8-Lead Cerdip (Q) Packages APPLICATIONS Output Buffers for 12-Bit, 14-Bit and 16-Bit DACs, ADC Buffers, Cable Drivers, Wideband Preamplifiers and Active Filters PRODUCT DESCRIPTION The AD744 is a fast-settling, precision, FET input, monolithic operational amplifier. It offers the excellent dc characteristics of the AD711 BiFET family with enhanced settling, slew rate, and bandwidth. The AD744 also offers the option of using custom compensation to achieve exceptional capacitive load drive capability. The single-pole response of the AD744 provides fast settling: 500 ns to 0.01%. This feature, combined with its high dc precision, makes it suitable for use as a buffer amplifier for 12-bit, 14-bit or 16-bit DACs and ADCs. Furthermore, the AD744's low total harmonic distortion (THD) level of 0.0003% and gain bandwidth product of 13 MHz make it an ideal amplifier for demanding audio applications. It is also an excellent choice for use in active filters in 12-bit, 14-bit and 16-bit data acquisition systems. The AD744 is internally compensated for stable operation as a unity gain inverter or as a noninverting amplifier with a gain of two or greater. External compensation may be applied to the AD744 for stable operation as a unity gain follower. External compensation also allows the AD744 to drive 1000 pF capacitive loads, slewing at 10 V/s with full stability. Alternatively, external decompensation may be used to increase the gain bandwidth of the AD744 to over 200 MHz at high Rev. D gains. This makes the AD744 ideal for use as ac preamps in digital signal processing (DSP) front ends. The AD744 is available in five performance grades. The AD744J and AD744K are rated over the commercial temperature range of 0C to +70C. The AD744A and AD744B are rated over the industrial temperature range of -40C to +85C. The AD744T is rated over the military temperature range of -55C to +125C and is available processed to MIL-STD-883B, Rev. C. The AD744 is available in an 8-lead plastic mini-DIP, 8-lead small outline, 8-lead cerdip or TO-99 metal can. PRODUCT HIGHLIGHTS 1. The AD744 is a high-speed BiFET op amp that offers excellent performance at competitive prices. It outperforms the OPA602/OPA606, LF356 and LF400. 2. The AD744 offers exceptional dynamic response. It settles to 0.01% in 500 ns and has a 100% tested minimum slew rate of 50 V/s (AD744B). 3. The combination of Analog Devices' advanced processing technology, laser wafer drift trimming and well-matched ionimplanted JFETs provide outstanding dc precision. Input offset voltage, input bias current, and input offset current are specified in the warmed-up condition; all are 100% tested. Document Feedback Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 (c)2007-2017 Analog Devices, Inc. All rights reserved. Technical Support www.analog.com AD744-SPECIFICATIONS (@ +25C and 15 V dc, unless otherwise noted) AD744J/A/S Model INPUT OFFSET VOLTAGE 1 Initial Offset Offset vs. Temp. vs. Supply2 vs. Supply Long-Term Stability INPUT BIAS CURRENT 3 Either Input Either Input @ T MAX = J, K A, B, C S, T Either Input Offset Current Offset Current @ T MAX = J, K A, B, C S, T FREQUENCY RESPONSE Gain BW, Small Signal Full Power Response Slew Rate, Unity Gain Settling Time to 0.01% 4 Total Harmonic Distortion Conditions Min 0.3 TMIN to TMAX TMIN to TMAX 82 82 5 95 AD744K/B/T Max Min 1.0 2 20 VCM = 0 V VCM = 0 V 70C 85C 125C VCM = +10 V VCM = 0 V VCM = 0 V 70C 85C 125C G = -1 VO = 20 V p-p G = -1 G = -1 f = 1 kHz R1 2 k VO = 3 V rms 8 45 88 88 78 76 72 70 5 100 Max Unit 0.5 1.0 10 mV mV V/C dB dB V/month 15 30 100 30 100 pA 0.7 1.9 31 40 20 2.3 6.4 102 150 50 0.7 1.9 31 40 10 2.3 6.4 102 150 50 nA nA nA pA pA 0.4 1.3 20 1.1 3.2 52 0.2 0.6 10 1.1 3.2 52 nA nA nA 0.75 MHz MHz V/s s 13 1.2 75 0.5 9 50 0.75 13 1.2 75 0.5 0.0003 0.0003 % 3 1012||5.5 3 1012||5.5 3 1012||5.5 3 1012||5.5 ||pF ||pF 20 +14.5, -11.5 -11 20 +14.5, -11.5 +13 V V V 82 80 78 74 88 84 84 80 dB dB dB dB -11 VCM = 10 V TMIN to TMAX VCM = 11 V TMIN to TMAX Typ 0.25 15 INPUT IMPEDANCE Differential Common Mode INPUT VOLTAGE RANGE Differential5 Common-Mode Voltage Over Max Operating Range 6 Common-Mode Rejection Ratio Typ +13 88 84 84 80 0.1 to 10 Hz f = 10 Hz f = 100 Hz f = 1 kHz f = 10 kHz 2 45 22 18 16 2 45 22 18 16 V p-p nV/Hz nV/Hz nV/Hz nV/Hz INPUT CURRENT NOISE f = 1 kHz 0.01 0.01 pA/Hz OPEN LOOP GAIN 7 VO = 10 V RLOAD 2 k TMIN to TMAX INPUT VOLTAGE NOISE OUTPUT CHARACTERISTICS Voltage Current Capacitive Load8 POWER SUPPLY Rated Performance Operating Range Quiescent Current RLOAD 2 k TMIN to TMAX Short Circuit Gain = -1 200 100 400 250 100 400 V/mV V/mV +13, -12.5 12 +13.9, -13.3 +13.8, -13.1 25 +13, -12.5 12 +13.9, -13.3 +13.8, -13.1 25 1000 V V mA pF 15 V V mA 1000 4.5 15 3.5 18 5.0 4.5 3.5 18 4.0 NOTES 1 Input offset voltage specifications are guaranteed after 5 minutes of operation at TA = +25C. 2 PSRR test conditions: +VS = 15 V, -VS = -12 V to -18 V and +VS = +12 V to +18 V, -VS = -15 V. 3 Bias Current Specifications are guaranteed maximum at either input after 5 minutes of operation at TA = +25C. For higher temperature, the current doubles every 10C. 4 Gain = -1, RL = 2 k, CL = 10 pF, refer to Figure 25. 5 Defined as voltage between inputs, such that neither exceeds 10 V from ground. 6 Typically exceeding -14.1 V negative common-mode voltage on either input results in an output phase reversal. 7 Open-Loop Gain is specified with VOS both nulled and unnulled. 8 Capacitive load drive specified for CCOMP = 20 pF with the device connected as shown in Figure 32. Under these conditions, slew rate = 14 V/s and 0.01% settling time = 1.5 s typical. Refer to Table II for optimum compensation while driving a capacitive load. Specifications subject to change without notice. All min and max specifications are guaranteed. -2- REV. D AD744 ABSOLUTE MAXIMUM RATINGS 1 Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 V Internal Power Dissipation2 . . . . . . . . . . . . . . . . . . . . 500 mW Input Voltage3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 V Output Short Circuit Duration . . . . . . . . . . . . . . . . Indefinite Differential Input Voltage . . . . . . . . . . . . . . . . . . +VS and -VS Storage Temperature Range (Q, H) . . . . . . -65C to +150C Storage Temperature Range (N, R) . . . . . . . -65C to +125C Operating Temperature Range AD744J/K . . . . . . . . . . . . . . . . . . . . . . . . . . . 0C to +70C AD744A/B . . . . . . . . . . . . . . . . . . . . . . . . . -40C to +85C AD744S/T . . . . . . . . . . . . . . . . . . . . . . . . -55C to +125C Lead Temperature Range (Soldering 60 seconds) . . . . . 300C NOTES 1 Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. 2 Thermal Characteristics 8-Lead Plastic Package: JA = 100C/Watt, JC = 33C/Watt 8-Lead Cerdip Package: JA = 110C/Watt, JC = 22C/Watt 8-Lead Metal Can Package: JA = 150C/Watt, JC = 65C/Watt 8-Lead SOIC Package: JA = 160C/Watt, JC = 42C/Watt 3 For supply voltages less than 18 V, the absolute maximum input voltage is equal to the supply voltage. METALIZATION PHOTOGRAPH Contact factory for latest dimensions. Dimensions shown in inches and (mm). REV. D -3- AD744 -Typical Characteristics Figure 1. Input Voltage Swing vs. Supply Voltage Figure 2. Output Voltage Swing vs. Supply Voltage Figure 4. Quiescent Current vs. Supply Voltage Figure 5. Input Bias Current vs. Temperature Figure 7. Input Bias Current vs. Common-Mode Voltage Figure 8. Short Circuit Current Limit vs. Temperature -4- Figure 3. Output Voltage Swing vs. Load Resistance Figure 6. Output Impedance vs. Frequency Figure 9. Gain Bandwidth Product vs. Temperature REV. D AD744 Figure 10. Open-Loop Gain and Phase Margin vs. Frequency CCOMP = 0 pF Figure 11. Open Loop Gain and Phase Margin vs. Frequency CCOMP = 25 pF Figure 13. Common-Mode and Power Supply Rejection vs. Frequency Figure 14. Large Signal Frequency Response Figure 15. Output Swing and Error vs. Settling Time Figure 17. Input Noise Voltage Spectral Density Figure 18. Slew Rate vs. Input Error Signal Figure 16. Total Harmonic Distortion vs. Frequency, Circuit of Figure 20 (G = 10) REV. D -5- Figure 12. Open-Loop Gain vs. Supply Voltage AD744 -Typical Characteristics Figure 19. Settling Time vs. Closed Loop Voltage Gain Figure 22a. Unity-Gain Follower Figure 23a. Unity-Gain Inverter Figure 20. THD Test Circuit Figure 22b. Unity-Gain Follower Large Signal Pulse Response, CCOMP = 5 pF Figure 23b. Unity-Gain Inverter Large Signal Pulse Response, CCOMP = 5 pF -6- Figure 21. Offset Null Configuration Figure 22c. Unity-Gain Follower Small Signal Pulse Response, CCOMP = 5 pF Figure 23c. Unity-Gain Inverter Small Signal Pulse Response, CCOMP = 0 pF REV. D AD744 POWER SUPPLY BYPASSING The power supply connections to the AD744 must maintain a low impedance to ground over a bandwidth of 10 MHz or more. This is especially important when driving a significant resistive or capacitive load, since all current delivered to the load comes from the power supplies. Multiple high quality bypass capacitors are recommended for each power supply line in any critical application. A 0.1 F ceramic and a 1 F electrolytic capacitor as shown in Figure 24 placed as close as possible to the amplifier (with short lead lengths to power supply common) will assure adequate high frequency bypassing, in most applications. A minimum bypass capacitance of 0.1 F should be used for any application. The error signal is thus clamped twice: once to prevent overloading amplifier A2 and then a second time to avoid overloading the oscilloscope preamp. A Tektronix oscilloscope preamp type 7A26 was carefully chosen because it recovers from the approximately 0.4 V overload quickly enough to allow accurate measurement of the AD744's 500 ns settling time. Amplifier A2 is a very high-speed FET-input op amp; it provides a voltage gain of 10, amplifying the error signal output of the AD744 under test. +VS 1F 0.1F AD744 1F 0.1F -VS Figure 24. Recommended Power Supply Bypassing Figure 26. Settling Characteristics 0 to +10 V Step Upper Trace: Output of AD744 Under Test (5 V/div.) Lower Trace: Amplified Error Voltage (0.01%/div.) MEASURING AD744 SETTLING TIME The photos of Figures 26 and 27 show the dynamic response of the AD744 while operating in the settling time test circuit of Figure 25. The input of the settling time fixture is driven by a flat-top pulse generator. The error signal output from the false summing node of A1, the AD744 under test, is clamped, amplified by op amp A2 and then clamped again. +15V TO TEKTRONIX 7A26 1M 20pF OSCILLOSCOPE PREAMP INPUT SECTION (VIA LESS THAN 1 FT 50 COAXIAL CABLE) VERROR 10 206 +VS COM -15V 5pF -VS A2 AD3554 2X HP2835 2X HP2835 0.47F +VS 0.47F -VS Figure 27. Settling Characteristics 0 to -10 V Step Upper Trace: Output of AD744 Under Test (5 V/div.) Lower Trace: Amplified Error Voltage (0.01%/div.) 10k 1.1k 0.2pF - 0.8pF NULL 4.99k 4.99k 200 FLAT-TOP PULSE GENERATOR 10k 5pF - 18pF VIN AD744 10k A1 DATA DYNAMICS 5109 OR EQUIVALENT 5k 10pF +VS 1F 0.1F -VS 1F 0.1F NOTE: USE CIRCUIT BOARD WITH GROUND PLANE Figure 25. Settling Time Test Circuit REV. D -7- AD744 EXTERNAL FREQUENCY COMPENSATION The following section provides tables to show what C COMP values will provide the necessary compensation for given circuit configurations and capacitive loads. In each case, the recommended C COMP is a minimum value. A larger CCOMP can always be used, but slew rate and bandwidth performance will be degraded. Even though the AD744 is useable without compensation in most applications, it may be externally compensated for even more flexibility. This is accomplished by connecting a capacitor between Pins 5 and 8. Figure 28, a simplified schematic of the AD744, shows where this capacitor is connected. This feature is useful because it allows the AD744 to be used as a unity gain voltage follower. It also enables the amplifier to drive capacitive loads up to 2000 pF and greater. Figure 30 shows the AD744 configured as a unity gain voltage follower. In this case, a minimum compensation capacitor of 5 pF is necessary for stable operation. Larger compensation capacitors can be used for driving larger capacitive loads. Table I outlines recommended minimum values for CCOMP based on the desired capacitive load. It also gives the slew rate and bandwidth that will be achieved for each case. +VS 400A 2mA 300 300 -IN +IN 5pF NULL / COMPENSATION +VS OUTPUT 1F NULL / DECOMPENSATION 0.1F AD744 VOUT COMPENSATION 1k 1k VIN 8k CCOMP 5pF -VS 1F Figure 28. AD744 Simplified Schematic The slew rate and gain bandwidth product of the AD744 are inversely proportional to the value of the compensation capacitor, C COMP. Therefore, when trying to maximize the speed of the amplifier, the value of CCOMP should be minimized. CCOMP can also be used to slow the amplifier to a point where the slew rate is perfectly symmetrical and well controlled. Figure 29 summarizes the effect of external compensation on slew rate and bandwidth. Figure 30. AD744 Connected as a Unity Gain Voltage Follower Table I. Recommended Values of C COMP vs. Various Capacitive Loads 100 2 10 0.2 1.0 0.02 0 10 100 SLEW RATE - V/s GAIN BANDWIDTH - MHz 20 0.1F -VS Gain Max CLOAD (pF) CCOMP (pF) Slew Rate (V/s) -3 dB Bandwidth (MHz) 1 1 1 50 150 2000 5 10 25 37 25 12.5 6.5 4.3 2.0 Figures 31 and 32 show the AD744 as a voltage follower with gain and as an inverting amplifier. In these cases, external compensation is not necessary for stable operation. However, compensation may be applied to drive capacitive loads above 50 pF. Table II gives recommended CCOMP values, along with expected slew rates and bandwidths for a variety of load conditions and gains for the circuits in Figures 31 and 32. CLEAD* 0.1 1000 R1* CCOMP - pF R2* +VS Figure 29. Gain Bandwidth and Slew Rate vs. CCOMP 1F 0.1F AD744 OPTIONAL CCOMP VIN *SEE TABLE II VOUT 1F 0.1F -VS Figure 31. AD744 Connected as a Voltage Follower Operating at Gains of 2 or Greater -8- REV. D AD744 Table II. Recommended Values of C COMP vs. Various Load Conditions for the Circuits of Figures 31 and 32. R1 () 4.99 k 4.99 k 4.99 k 4.99 k 499 499 499 R2 () Gain Follower 4.99 k 4.99 k 4.99 k 4.99 k 4.99 k 4.99 k 4.99 k 2 2 2 2 11 11 11 Gain Inverter Max CLOAD (pF) CCOMP (pF) 1 1 1 1 10 10 10 50 150 1000 >2000 270 390 1000 0 5 20 25 0 2 5 CLEAD (pF) 7 7 - - - - - Slew Rate (V/s) -3 dB Bandwidth (MHz) 75 37 14 12.52 75 50 372 2.51 2.31 1.2 1.0 1.2 0.85 0.60 NOTES 1 Bandwidth with C LEAD adjusted for minimum settling time. 2 Into large capacitive loads the AD744's 25 mA output current limit sets the slew rate of the amplifier, in V/ s, equal to 0.025 amps divided by the value of C LOAD in F. Slew rate is specified into rated max C LOAD except for cases marked 2, which are specified with a 50 pF. load. CLEAD* Due to manufacturing variations in the value of the internal C COMP , it is recommended that the amplifier's response be optimized for the desired gain by using a 2 to 10 pF trimmer capacitor rather than using a fixed value. R2* +VS 1F R1* 0.1F VIN R2* R1* AD744 VOUT +VS 1F OPTIONAL 0.1F CCOMP *SEE TABLE II 1F AD744 0.1F VOUT -VS \ Figure 32. AD744 Connected as an Inverting Amplifier Operating at Gains of 1 or Greater NOT CONNECTED VIN 2 - 10pF *SEE TABLE III 1F 0.1F -VS Using Decompensation to Extend the Gain Bandwidth Product When the AD744 is used in applications where the closed-loop gain is greater than 10, gain bandwidth product may be enhanced by connecting a small capacitor between Pins 1 and 5 (Figure 33). At low frequencies, this capacitor cancels the effects of the chip's internal compensation capacitor, CCOMP, effectively decompensating the amplifier. REV. D Figure 33. Using the Decompensation Connection to Extend Gain Bandwidth Table III. Performance Summary for the Circuit of Figure 33 R1 () R2 () 1k 100 100 10 k 11 10 k 101 100 k 1001 -9- Gain Follower Gain Inverter -3 dB Bandwidth Gain/BW Product 10 100 1000 2.5 MHz 760 kHz 225 kHz 25 MHz 76 MHz 225 MHz AD744 VCC REF OUT GAIN ADJUST 100 0.1F 100 BIPOLAR OFFSET ADJUST 20V SPAN 10V REF IN AD565A CLEAD 5k 10V SPAN 9.96k 19.95k +15V 10pF 1F 5k DAC OUT REF GND 20k 8k AD744 1F 0.1F POWER GND MSB -15V LSB -VEE Figure 34. 10 V Voltage Output Bipolar DAC Using the AD744 as an Output Buffer HIGH-SPEED OP AMP APPLICATIONS AND TECHNIQUES A HIGH-SPEED, 3 OP AMP INSTRUMENTATION AMPLIFIER CIRCUIT DAC Buffers (I-to-V Converters) The instrumentation amplifier circuit shown in Figure 36 can provide a range of gains from unity up to 1000 and higher. The circuit bandwidth is 4 MHz at a gain of 1 and 750 kHz at a gain of 10; settling time for the entire circuit is less than 2 s to within 0.01% for a 10 V step, (G = 10). Digital-to-analog converters which use bipolar transistors to switch currents into (or out of) their outputs can achieve very fast settling times. The AD565A, for example, is specified to settle to 12 bits in less than 250 ns, with a current output. However, in many applications, a voltage output is desirable, and it would be useful - perhaps essential - that this I-to-V conversion be accomplished without increasing the settling time or without degrading the accuracy of the DAC. Figure 34 is a schematic of an AD565A DAC using an AD744 output buffer. The 10 pF CLEAD capacitor compensates for the DAC's output capacitance, plus the 5.5 pF amplifier input capacitance. Figure 35 is an oscilloscope photo of the AD744's output voltage with a +10 V to 0 V step applied; this corresponds to an all "1s" to all "0s" code change on the DAC. Since the DAC is While the AD744 is not stable with 100% negative feedback (as when connected as a standard voltage follower), phase margin and therefore stability at unity gain may be increased to an acceptable level by placing the parallel combination of a resistor and a small lead capacitor between each amplifier's output and its inverting input terminal. The only penalty associated with this method is a small bandwidth reduction at low gains. The optimum value for CLEAD may be determined from the graph of Figure 41. This technique can be used in the circuit of Figure 36 to achieve stable operation at gains from unity to over 1000. CIRCUIT GAIN = 20,000 +1 RG AD744 *1.5pF - 20pF (TRIM FOR BEST SETTLING TIME) -IN A1 **10k 10k 7.5pF **10k 7.5pF RG SENSE A3 **10k 10k AD744 5pF **10k A2 REFERENCE +IN AD744 Figure 35. Upper Trace: AD744 Output Voltage for a +10 V to 0 V Step, Scale: 5 mV/div. Lower Trace: Logic Input Signal, Scale: 5 V/div. *VOLTRONICS SP20 TRIMMER CAPACITOR OR EQUIVALENT **RATIO MATCHED 1% METAL FILM RESISTORS +VS +15V 1F connected in the 20 V span mode, 1 LSB is equal to 4.88 mV. Output settling time for the AD565/AD744 combination is less than 500 ns to within a 2.44 mV, 1/2 LSB error band. PIN 7 1F 0.1F 1F 0.1F COMM 1F -15V -VS EACH AMPLIFIER PIN 4 FOR OPTIONAL OFFSET ADJUSTMENT: TRIM A1, A3 USING TRIM PROCEDURE SHOWN IN FIGURE 21. Figure 36. A High Performance, 3 Op Amp Instrumentation Amplifier Circuit -10- REV. D AD744 Table IV. Performance Summary for the 3 Op Amp Instrumentation Amplifier Circuit Gain RG Bandwidth T Settle (0.01%) 1 2 10 100 NC 20 k 2.22 k 202 3.5 MHz 2.5 MHz 1 MHz 290 kHz 1.5 s 1.0 s 2 s 5 s Equation 1 would completely describe the output of the system if not for the op amp's finite slew rate and other nonlinear effects. Even considering these effects, the fine scale settling to <0.1% will be determined by the op amp's small signal behavior. Equation 1. VO -R = I IN R (CL + CX ) 2 GN s + + R CL s + 1 2FO 2FO Where FO = the op amp's unity gain crossover frequency R GN = the "noise" gain of the circuit 1 + RO This Equation May Then Be Solved for CL: Equation 2. CL = 2 RC X 2FO + (1 - GN ) 2 - GN + R 2FO R 2FO In these equations, capacitance CX is the total capacitance appearing at the inverting terminal of the op amp. When modeling an I-to-V converter application, the Norton equivalent circuit of Figure 39 can be used directly. Capacitance CX is the total capacitance of the output of the current source plus the input capacitance of the op amp, which includes any stray capacitance at the op amp's input. Figure 37. The Pulse Response of the 3 Op Amp Instrumentation Amplifier. Gain = 1, l Horizontal Scale: 0.5 V/div., Vertical Scale: 5 V/div. (Gain= 10) CCOMP (OPTIONAL) AD744 VOUT RL CLOAD R IO RO CX CL Figure 39. A Simplified Model of the AD744 Used as a Current-to-Voltage Converter Figure 38. Settling Time of the 3 Op Amp Instrumentation Amplifier. Horizontal Scale: 500 ns/div., Vertical Scale, Pulse Input: 5 V/div., Output Settling: 1 mV/div. Minimizing Settling Time in Real-World Applications An amplifier with a "single pole" or "ideal" integrator open-loop frequency response will achieve the minimum possible settling time for any given unity-gain bandwidth. However, when this "ideal" amplifier is used in a practical circuit, the actual settling time is increased above the minimum value because of added time constants which are introduced due to additional capacitance on the amplifier's summing junction. The following discussion will explain how to minimize this increase in settling time by the selection of the proper value for feedback capacitor, CL. When RO and IO are replaced with their Thevenin VIN and RIN equivalents, the general purpose inverting amplifier model of Figure 40 is created. Here capacitor CX represents the input capacitance of the AD744 (5.5 pF) plus any stray capacitance due to wiring and the type of IC package employed. AD744 VOUT RL RIN VIN CLOAD R CX CL If an op amp is modeled as an ideal integrator with a unity gain crossover frequency, fO, Equation 1 will accurately describe the small signal behavior of the circuit of Figure 39. This circuit models an op amp connected as an I-to-V converter. REV. D CCOMP (OPTIONAL) Figure 40. A Simplified Model of the AD744 Used as an Inverting Amplifier -11- AD744 In either case, the capacitance CX causes the system to go from a one-pole to a two-pole response; this additional pole increases settling time by introducing peaking or ringing in the op amp's output. If the value of CX can be estimated with reasonable accuracy, Equation 2 can be used to choose the correct value for a small capacitor, CL, which will optimize amplifier response. If the value of CX is not known, CL should be a variable capacitor. VALUE OF CAPACITOR CLEAD - pF 35 As an aid to the designer, the optimum value of CL for one specific amplifier connection can be determined from the graph of Figure 41. This graph has been produced for the case where the AD744 is connected as in Figures 39 and 40 with a practical minimum value for CSTRAY of 2 pF and a total CX value of 7.5 pF. 30 GN = 1 25 20 GN = 1.5 15 10 5 IN THIS REGION CLEAD = 0pF GN = 1 TO The approximate value of CL can be determined for almost any application by solving Equation 2. For example, the AD565/ AD744 circuit of Figure 34 constrains all the variables of Equation 2 (GN = 3.25, R = 10 k, FO = 13 MHz, and CX = 32.5 pF) Therefore, under these conditions, CL= 10.5 pF. 0 100 GN = 2 GN = 3 1k 10k VALUE OF RESISTOR - 100k Figure 41. Practical Values of CL vs. Resistance of R for Various Amplifier Noise Gains -12- REV. D Data Sheet AD744 OUTLINE DIMENSION 0.400 (10.16) 0.365 (9.27) 0.355 (9.02) 5 4 0.015 (0.38) MIN SEATING PLANE 0.022 (0.56) 0.018 (0.46) 0.014 (0.36) 0.005 (0.13) MIN 5 0.310 (7.87) 0.220 (5.59) 0.325 (8.26) 0.310 (7.87) 0.300 (7.62) 1 0.060 (1.52) MAX 0.210 (5.33) MAX 0.150 (3.81) 0.130 (3.30) 0.115 (2.92) 8 0.280 (7.11) 0.250 (6.35) 0.240 (6.10) 0.100 (2.54) BSC 0.055 (1.40) MAX 0.195 (4.95) 0.130 (3.30) 0.115 (2.92) 4 0.100 (2.54) BSC 0.320 (8.13) 0.290 (7.37) 0.405 (10.29) MAX 0.015 (0.38) GAUGE PLANE 0.014 (0.36) 0.010 (0.25) 0.008 (0.20) 0.060 (1.52) 0.015 (0.38) 0.200 (5.08) MAX 0.430 (10.92) MAX 0.150 (3.81) MIN 0.200 (5.08) 0.125 (3.18) 0.070 (1.78) 0.060 (1.52) 0.045 (1.14) 0.023 (0.58) 0.014 (0.36) 070606-A COMPLIANT TO JEDEC STANDARDS MS-001 CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. CORNER LEADS MAY BE CONFIGURED AS WHOLE OR HALF LEADS. SEATING PLANE 0.070 (1.78) 0.030 (0.76) 5.00 (0.1968) 4.80 (0.1890) 8 1 5 6.20 (0.2441) 5.80 (0.2284) 4 1.27 (0.0500) BSC 0.25 (0.0098) 0.10 (0.0040) COPLANARITY 0.10 SEATING PLANE 0.015 (0.38) 0.008 (0.20) Figure 43. 8-Lead Ceramic Dual In-Line Package [CERDIP] (Q-8) Dimensions shown in inches and (millimeters] Figure 42. 8-Lead Plastic Dual In-Line Package [PDIP] Narrow Body (N-8) Dimensions shown in inches and (millimeters] 4.00 (0.1574) 3.80 (0.1497) 15 0 CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. 1.75 (0.0688) 1.35 (0.0532) 0.51 (0.0201) 0.31 (0.0122) 0.50 (0.0196) 0.25 (0.0099) 45 8 0 0.25 (0.0098) 0.17 (0.0067) 1.27 (0.0500) 0.40 (0.0157) COMPLIANT TO JEDEC STANDARDS MS-012-AA CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. Figure 44. 8-Lead Standard Small Outline Package [SOIC_N] Narrow Body (R-8) Dimensions shown in inches and (millimeters] Rev. D | Page 13 of 15 012407-A 8 1 0.005 (0.13) MIN AD744 Data Sheet REFERENCE PLANE 0.50 (12.70) MIN 0.185 (4.70) 0.165 (4.19) 0.100 (2.54) BSC 0.250 (6.35) MIN 0.050 (1.27) MAX 0.160 (4.06) 0.140 (3.56) 5 0.370 (9.40) 0.335 (8.51) 0.021 (0.53) 0.016 (0.40) 6 4 0.200 (5.08) BSC 0.335 (8.51) 0.305 (7.75) 7 3 2 SIDE VIEW 0.040 (1.02) MAX 8 1 0.100 (2.54) BSC 0.019 (0.48) 0.016 (0.41) 0.045 (1.14) 0.027 (0.69) 0.034 (0.86) 0.028 (0.71) BOTTOM VIEW 45 BSC 0.040 (1.02) 0.010 (0.25) COMPLIANT TO JEDEC STANDARDS MO-002-AK CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. 01-15-2015-B BASE & SEATING PLANE Figure 45. 8-Pin Metal Header [TO_99] (H-08) Dimensions shown in inches and (millimeters] ORDERING GUIDE Model1 AD744JR AD744JRZ AD744JR-REEL AD744KRZ AD744KRZ-REEL AD744KRZ-REEL7 AD744AQ AD744BQ AD744JNZ AD744KNZ AD744JCHIPS AD744TH/883B 1 Temperature Range 0C to +70C 0C to +70C 0C to +70C 0C to +70C 0C to +70C 0C to +70C -40C to +85C -40C to +85C -40C to +85C -40C to +85C 0C to +70C -55C to +125C Package Description 8-Lead Standard Small Outline Package [SOIC_N] 8-Lead Standard Small Outline Package [SOIC_N] 8-Lead Standard Small Outline Package [SOIC_N] 8-Lead Standard Small Outline Package [SOIC_N] 8-Lead Standard Small Outline Package [SOIC_N] 8-Lead Standard Small Outline Package [SOIC_N] 8-Lead Ceramic Dual In-Line Package [CERDIP] 8-Lead Ceramic Dual In-Line Package [CERDIP] 8-Lead Plastic Dual In-Line Package [PDIP] 8-Lead Plastic Dual In-Line Package [PDIP] 8-Pin Metal Header [TO-99] Z = RoHS Compliant Part. Rev. D | Page 14 of 15 Package Option R-8 R-8 R-8 R-8 R-8 R-8 Q-8 Q-8 N-8 N-8 Die H-08 Data Sheet AD744 REVISION HISTORY 10/2017--Rev. C to Rev. D Updated Outline Dimensions ............................................................ 14 Changes to Ordering Guide ............................................................... 14 7/2000--Rev. B to Rev. C (c)2007-2017 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D00833-0-10/17(D) Rev. D | Page 15 of 15 Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Analog Devices Inc.: AD744JR-EBZ