SPECIFICATION CONTROL DRAWING
Tyco Electronics Corporation
300 Constitution Drive,
Menlo Park, CA. 94025, U.S.A. Raychem TITLE: SOLDERGRIP DEVICE
STUB SPLICE
Unless otherwise specified dimensions are in millimeters.
[Inches dimensions are shown in brackets] DOCUMENT NO.: SGRS-X
TOLERANCES:
0.00 N/A
0.0 N/A
0 N/A
ANGLES: N/A
ROUGHNESS IN
MICRON
Tyco Electronics reserves the right to amend
this drawing at any time. Users should
evaluate the suitability of the product for their
application.
REV.: A DATE: 29-Nov-06
DRAWN BY:
P.TALLY CAGE CODE:
06090 REPLACES:
D040187 DCR NUMBER:
D060343 SCALE: NTS SIZE: A SHEET: 1 of 1
© 2006 Tyco Electronics Corporation. All rights reserved.
If this document is printed it becomes uncontrolled. Check for the latest revision.
Product Dimensions Copper Cross Section Bundle Diameter
Product
Name Ball
Color L±3.5
(L±0.140) øA
B
Min.
mm2 (CMA) Max.
mm2 (CMA) øD
max M±1
(M±0.04)
SGRS-1 Green 38.3
(1.510)
3.6 +0.4/-0.2
(0.140 +0.016/-0.008) 26.0±2.0
(1.025±0.079) 0.7 (1400) 2.4 (4800) 3.3
(0.130) 15.0
(0.590)
SGRS-2 Red 37.7
(1.485) 5.0 +0.7/-0.2
(0.200 +0.028/-0.008) 23.5±2.0
(0.925±0.079) 2.0 (4000) 4.0(8000) 4.5
(0.175) 15.0
(0.590)
SGRS-3 Blue 45.5
(1.790) 7.5 +0.9/-0.2
(0.295 +0.035/-0.008) 26.5±2.0
(1.045±0.079) 3.5 (7000) 8.0(16000) 7.0
(0.275) 15.0
(0.590)
SGRS-4 Yellow 45.0
(1.770) 9.4 +0.9/-0.3
(0.370 +0.035/-0.012) 25.5±3.0
(1.005±0.118) 7.5 (15000) 12.0(24000) 9.0
(0.350) 15.0
(0.590)
These products are tested to RB109.
MATERIALS
1. INSULATION SLEEVE: Heat-shrinkable, transparent blue, radiation cross-linked modified polyvinylidene fluoride.
2. SOLDER PREFORM WITH FLUX:
SOLDER: TYPE Sn60 per ANSI-J-STD-006.
FLUX: TYPE ROM1 per ANSI-J-STD-004.
3. CONICAL SPRING: Square copper wire.
4. END CLOSURE BALL: Tinted glass. Color: see table.
5. SEALING INSERT: Hot melt adhesive.
APPLICATION
1. These controlled soldering devices are designed for stub splicing of stranded wires, with bare copper conductors and an
insulation rated for 85°C minimum and 125°C continuous maximum.
2. Temperature range: Class 3, -40°C to +125°C.
3. Vibration range: Class 1 (body).
4. Seal range: Class 2 (watertight against immersion). Immersion resistant sealing is dependent on the wire combinations used.
The user should test specific wire combinations. Refer to Tyco Electronics / Raychem Specification RB109 for procedures.
5. For installation procedure and application equipment, consult RPIP-820-00.
For best results, prepare the cable as shown:
