TFDU6100/TFDS6500/TFDT6500 Not for new designs Vishay Telefunken 5 V Fast Infrared Transceiver Module Family (FIR, 4 Mbit/s) Description The TFDU6100, TFDS6500, and TFDT6500 are a family of low-power infrared transceiver modules compliant to the latest IrDA physical layer standard for fast infrared (FIR) data communication, supporting IrDA speeds up to 4.0 Mbit/s, HP-SIR, Sharp ASK and carrier based remote control modes up to 2 MHz. Integrated within the transceiver modules are a photo PIN diode, infrared emitter (IRED), and a low-power CMOS control IC to provide a total front-end solution in a single package. Vishay Telefunken's FIR transceivers are available in three package options, including our Baby Face package (TFDU6100), the smallest FIR transceiver available on the market. This wide selection provides flexibility for a variety of applications and space constraints. The transceivers are capable of directly interfacing with a wide variety of I/O chips which perform the modulation/ demodulation function, including National Semiconductor's PC87338, PC87108 and PC87109, SMC's FDC37C669, FDC37N769 and CAM35C44, and Hitachi's SH3. At a minimum, a current-limiting resistor in series with the infrared emitter and a VCC bypass capacitor are the only external components required to implement a complete solution. Features Compliant to latest IrDA physical specification (Up to 4 Mbit/s), HP-SIR, Sharp ASK and TV Remote layer For 4.5 V to 5.5 V Operating Voltage Baby Face (Universal) Package Capable of Surface Mount Solderability to Side and Top View Orientation Low-Power Consumption (5 mA Supply Current) Directly Interfaces with Various Super I/O and Controller Devices Power Shutdown Mode (35 A Shutdown Current) Built-In EMI Protection - No External Shielding Necessary Three Surface Mount Package Options - Universal (9.7 x 4.7 x 4.0 mm) - Side View (13.0 x 5.95 x 5.3 mm) - Top View (13.0 x 7.6 x 5.95 mm) Few External Components Required Backward Compatible to all Telefunken SIR and FIR Infrared Transceivers Applications Notebook Computers, Desktop PCs, Palmtop Computers (Win CE, Palm PC), PDAs Telecommunication Products (Cellular Phones, Pagers) Digital Still and Video Cameras Internet TV Boxes, Video Conferencing Systems Printers, Fax Machines, Photocopiers, Screen Projectors External Infrared Adapters (Dongles) Medical and Industrial Data Collection Devices Package Options TFDU6100 Baby Face (Universal) Document Number 82517 Rev. A4, 22-Jan-01 TFDS6500 Side View TFDT6500 Top View www.vishay.com 1 TFDU6100/TFDS6500/TFDT6500 Not for new designs Vishay Telefunken Ordering Information Part Number TFDU6100-TR3 TFDU6100-TT3 TFDS6500-TR3 TFDT6500-TR3 Qty / Reel 1000 pcs 1000 pcs 750 pcs 750 pcs Description Oriented in carrier tape for side view surface mounting Oriented in carrier tape for top view surface mounting Functional Block Diagram VCC Driver Amplifier Rxd Comparator IRED Anode AGC Logic SD/Mode Txd IRED Cathode Open Drain Driver 14871 GND Figure 1. Functional Block Diagram Pin Description Pin Number "U" and "T" Option "S" Option 1 8 2 1 3 4 7 2 5 6 7 8 6 3 5 4 www.vishay.com 2 Function Description Descri tion IRED anode, to be externally connected to VCC through a current control resistor IRED Cathode IRED cathode, internally connected to driver transistor Txd Transmit Data Input Rxd Received Data Output, push-pull CMOS driver output capable of driving a standard CMOS or TTL load. No external pull-up or pull-down resistor is required (pin is floating when device is in shutdown mode) SD/Mode Shutdown/Mode VCC Supply Voltage NC Do not connect GND Ground I/O Active I O HIGH LOW I HIGH IRED Anode Document Number 82517 Rev. A4, 22-Jan-01 TFDU6100/TFDS6500/TFDT6500 Not for new designs "U" Option Baby Face (Universal) IRED Vishay Telefunken "S" Option Side View "T" Option Top View IRED Detector IRED 14885 Detector Detector Figure 2. Pinnings Absolute Maximum Ratings Reference point Pin GND unless otherwise noted. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing. Parameters Supply Voltage Range Power Dissipation Junction Temperature Ambient Temperature Range (Operating) Storage Temperature Range Soldering Temperature Test Conditions See Derating Curve Min. - 0.5 Tstg Typ. -25 Max. 6 350 125 +85 Unit V mW C C -25 +85 C 240 C 130 600 mA mA See Recommended Solder Profile (see figure 9) Average Output Current Repetitive Pulsed Output <90 s, ton <20% Current IRED Anode Voltage Transmitter Data Input Voltage Receiver Data Output Voltage Virtual Source Size Method: (1-1/e) encircled energy Maximum Intensity for EN60825, 1997 Class 1 Operation of IEC825-1 or EN60825-1 (worst case IrDA FIR pulse pattern) Document Number 82517 Rev. A4, 22-Jan-01 Symbol VCC PD TJ Tamb IIRED (DC) IIRED (RP) VIREDA VTxd - 0.5 - 0.5 VCC+0.5 VCC+0.5 V V VRxd - 0.5 VCC+0.5 V d 2.5 2.8 mm 320 mW/sr www.vishay.com 3 TFDU6100/TFDS6500/TFDT6500 Not for new designs Vishay Telefunken Electrical Characteristics Tamb = 25_C, VCC = 5.0 V unless otherwise noted. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing. Parameters Transceiver Supply Voltage Dynamic Supply Current Standby Supply Current Operating Temperature Range Output Voltage Low Output Voltage High Input Voltage Low (Txd) Input Voltage High (Txd) Input Voltage Low (SD/Mode) Input Voltage High (SD/Mode) Input Leakage Current Input Capacitance www.vishay.com 4 Test Conditions / Pins SD = Low Receive mode only. In transmit mode, add additional 100 mA (typ) for IRED current. SD = VCC -0.5 IOL = 2.5 mA IOH = -2.5 mA Symbol Min. Typ. Max. Unit VCC ICC 4.5 5 5 5.5 7 V mA 35 100 +85 A C 0.3 0.5 V V V V V ISD TA -25 VOL VOH VIL VIH VIL VCC-0.5 0 3.5 0 VIH VCC -0.5 IL CI -10 0.8 0.8 V +10 5 A pF Document Number 82517 Rev. A4, 22-Jan-01 TFDU6100/TFDS6500/TFDT6500 Not for new designs Vishay Telefunken Optoelectronic Characteristics Tamb = 25_C, VCC = 5.0 V unless otherwise noted. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing. Parameters Receiver Minimum Detection Threshold Irradiance Maximum Detection Threshold Irradiance Logic LOW Receiver Input Irradiance Rise Time of Output Signal Fall Time of Output Signal Rxd Pulse Width of Out Output ut Signal, 50% Jitter, Leading Edge Latency Transmitter IRED Operating Current Output Radiant Intensity Radiant Intensity, Half - Intensity Angle Peak - Emission Wavelength Optical Rise Time, Fall Time Optical Overshoot Document Number 82517 Rev. A4, 22-Jan-01 Test Conditions 9.6 kbit/s to 115.2 kbit/s, l = 850 nm - 900 nm 1.152 Mbit/s to 4 Mbit/s, l = 850 nm - 900 nm Symbol Min. Typ. Max. Unit Ee 25 35 mW/m 2 Ee 70 80 mW/m 2 kW/m 2 Ee 5 10 Ee 4 10% to 90%, @2.2 k, 15pF tr (Rxd) 10 40 ns 90% to 10%, @2.2 k, 15pF Input pulse length 20 s, 9.6 kbit/s Input pulse length 125 ns, 4.0 Mbit/s mode Input pulse length 250 ns, 4.0 Mbit/s mode (double pulse) Input Irradiance = 90 mW/m2, 4.0 Mbit/s mode tf (Rxd) tPW tPW 10 0.8 60 40 20 165 ns s ns tPW 185 290 ns 10 ns 120 s 0.4 0.55 0.04 A mW/sr 140 320 mW/sr mW/m 2 tL R1 = 7.2 , VCC = 5.0 V Vcc = 5.0 V, = 0_, 15_ Txd = Low or SD = High (Receiver is inactive as long as SD = High) R1 = 7.2 Vcc = 5.0 V, = 0_, 15_ Txd = High, SD = Low, R1 = 7.2 ID Ie Ie 100 24 a1/2 _ lP 880 900 nm tropt, tfopt 10 40 ns 25 % www.vishay.com 5 TFDU6100/TFDS6500/TFDT6500 Not for new designs Vishay Telefunken Recommended Circuit Diagram The only required component for designing an IrDA 1.2 compatible design using Telefunken FIR transceivers is a current limiting resistor, R1, to the IRED. However, depending on the entire system design and board layout, additional components may be required (see figure KEIN MERKER). VCC R1 IRED Cathode R2 Rxd IRED Anode R1 see figure KEIN MERKER. For IrDA compliant operation, a current control resistor of 7.2 is recommended. The upper drive current limitation is dependent on the duty cycle and is given by the absolute maximum ratings on the data sheet. R2, C1 and C2 are optional and dependent on the quality of the supply voltage VCC and injected noise. An unstable power supply with dropping voltage during transmission may reduce sensitivity (and transmission range) of the transceiver. Txd Rxd 500 TFDx6x00 C2 5.0V 400 GND GND max. intensity in emission cone 15 5.25V SD/Mode NC SD/Mode Txd Note: Outlined components are optional depending on the quality of the power supply 14872 Intensity (mW/sr) C1 Vcc min. Rdson, min. VF 300 200 5.0V 100 Vcc=4.75V max.Rdson, max.VF min. intensity in emission cone 15 Figure 3. Recommended Application Circuit 0 Telefunken FIR transceivers integrate a sensitive receiver and a built-in power driver. The combination of both needs a careful circuit board layout. The use of thin, long resistive and inductive wiring should be avoided. The inputs (Txd, SD/Mode) and the output Rxd should be directly (DC) coupled to the I/O circuit. R1 is used for controlling the current through the IR emitter. For increasing the output power of the IRED, the value of the resistor should be reduced. Similarly, to reduce the output power of the IRED, the value of the resistor should be increased. For typical values of 0 14379 2 4 6 8 10 12 14 Current Control Resistor ( W ) 16 Figure 4. Intesity Ie vs. Current Control Resistor R1 The placement of these parts is critical. It is strongly recommended to position C2 as near as possible to the transceiver power supply pins. A tantalum capacitor should be used for C1 while a ceramic capacitor is used for C2. Also, when connecting the described circuit to the power supply, low impedance wiring should be used. Table 1. Recommended Application Circuit Components Component Recommended Value C1 4.7 mF, Tantalum C2 0.1 F, Ceramic R1 7.2 , 0.25 W (recommend using two 3.6 W, 0.125 W resistors in series) R2 www.vishay.com 6 47 , 0.125 W Vishay Part Number 293D 475X9 016B 2T VJ 1206 Y 104 J XXMT CRCW-1206-3R60-F-RT2 CRCW-1206-47R0-F-RT2 Document Number 82517 Rev. A4, 22-Jan-01 TFDU6100/TFDS6500/TFDT6500 Not for new designs Vishay Telefunken Mode Switching The TFDU6100, TFDS6500 and TFDT6500 powers on with a default of low frequency mode. The low frequency mode covers speeds up to 115.2 kbit/s. Signals with higher data rates should be detected in the high frequency mode. Lower frequency data can also be received in the high frequency mode but with reduced sensitivity. To switch the transceivers from low frequency mode to the 4.0 Mbit/s mode and vice versa, the programming sequences described below are required. 1. Set SD/MODE input to logic "HIGH". 2. Set Txd input to logic "HIGH". Wait ts 200 ns. 3. Set SD/MODE to logic "LOW" (this negative edge latches state of Txd, which determines speed setting). 4. After waiting th 200 ns Txd can be set to logic "LOW". The hold time of Txd is limited by the maximum allowed pulse length. Txd is now enabled as normal Txd input for the high bandwidth mode. 50% SD/Mode Setting to the High Bandwidth Mode (0.576 Mbit/s to 4.0 Mbit/s) Setting to the Lower Bandwidth Mode (2.4 kbit/s to 115.2 kbit/s) ts th 1. Set SD/MODE input to logic "HIGH". High : FIR Txd 50% 2. Set Txd input to logic "LOW". Wait ts 200 ns. 50% Low : SIR 14873 3. Set SD/MODE to logic "LOW" (this negative edge latches state of Txd, which determines speed setting). 4. Txd must be held for th 200 ns. Figure 5. Mode Switching Timing Diagram Document Number 82517 Rev. A4, 22-Jan-01 Txd is now enabled as normal Txd input for the lower bandwidth mode. www.vishay.com 7 TFDU6100/TFDS6500/TFDT6500 Not for new designs Vishay Telefunken Recommended SMD Pad Layout The leads of the device should be soldered in the center position of the pads. 7x1=7 0.6 2.5 1 8 1 15067 Figure 6. TFDU6100 BabyFace (Universal) 11.8 5.1 2.5 8 2.5 7 6 5 1.8 0.63 1.1 1.0 0.6 8.3 1 2.2 1 2.5 2 2.5 3 4 5.08 15069 Figure 7. TFDS6500 Side View Package 8.89 1.27 0.8 1.8 1 8 15068 Figure 8. TFDT6500 Top View Package Note: Leads of the device should be at least 0.3 mm within the ends of the pads. Pad 1 is longer to designate Pin 1 connection to transceiver. www.vishay.com 8 Document Number 82517 Rev. A4, 22-Jan-01 TFDU6100/TFDS6500/TFDT6500 Not for new designs Recommended Solder Profile Current Derating Diagram 10 s max. @ 230C 210 2 - 4C/s 180 150 120 120 - 180 s 90 60 90 s max. 2 - 4C/s 30 Peak Operating Current ( mA ) 600 240 Temperature ( C ) Vishay Telefunken 0 0 50 100 14874 150 200 250 Time ( s ) 300 Document Number 82517 Rev. A4, 22-Jan-01 400 300 200 Current derating as a function of the maximum forward current of IRED. Maximum duty cycle: 25%. 100 0 -40 -20 0 350 Figure 9. Recommended Solder Profile 500 14875 20 40 60 80 100 120 140 Temperature ( C ) Figure 10. Current Derating Diagram www.vishay.com 9 TFDU6100/TFDS6500/TFDT6500 Vishay Telefunken Not for new designs TFDU6100 - Baby Face (Universal) Package (Mechanical Dimensions) 12249 www.vishay.com 10 Document Number 82517 Rev. A4, 22-Jan-01 TFDU6100/TFDS6500/TFDT6500 Not for new designs Vishay Telefunken TFDS6500 - Side View Package (Mechanical Dimensions) 14322 Document Number 82517 Rev. A4, 22-Jan-01 www.vishay.com 11 TFDU6100/TFDS6500/TFDT6500 Vishay Telefunken Not for new designs TFDT6500 - Top View Package (Mechanical Dimensions) 14325 www.vishay.com 12 Document Number 82517 Rev. A4, 22-Jan-01 TFDU6100/TFDS6500/TFDT6500 Not for new designs Vishay Telefunken Ozone Depleting Substances Policy Statement It is the policy of Vishay Semiconductor GmbH to 1. Meet all present and future national and international statutory requirements. 2. Regularly and continuously improve the performance of our products, processes, distribution and operating systems with respect to their impact on the health and safety of our employees and the public, as well as their impact on the environment. It is particular concern to control or eliminate releases of those substances into the atmosphere which are known as ozone depleting substances (ODSs). The Montreal Protocol (1987) and its London Amendments (1990) intend to severely restrict the use of ODSs and forbid their use within the next ten years. Various national and international initiatives are pressing for an earlier ban on these substances. Vishay Semiconductor GmbH has been able to use its policy of continuous improvements to eliminate the use of ODSs listed in the following documents. 1. Annex A, B and list of transitional substances of the Montreal Protocol and the London Amendments respectively 2. Class I and II ozone depleting substances in the Clean Air Act Amendments of 1990 by the Environmental Protection Agency (EPA) in the USA 3. Council Decision 88/540/EEC and 91/690/EEC Annex A, B and C (transitional substances) respectively. Vishay Semiconductor GmbH can certify that our semiconductors are not manufactured with ozone depleting substances and do not contain such substances. We reserve the right to make changes to improve technical design and may do so without further notice. Parameters can vary in different applications. All operating parameters must be validated for each customer application by the customer. Should the buyer use Vishay Telefunken products for any unintended or unauthorized application, the buyer shall indemnify Vishay Telefunken against all claims, costs, damages, and expenses, arising out of, directly or indirectly, any claim of personal damage, injury or death associated with such unintended or unauthorized use. Vishay Semiconductor GmbH, P.O.B. 3535, D-74025 Heilbronn, Germany Telephone: 49 ( 0 )7131 67 2831, Fax number: 49 ( 0 )7131 67 2423 Document Number 82517 Rev. A4, 22-Jan-01 www.vishay.com 13