LM3678 LM3678 High-Performance, Miniature 1.5A Step-Down DC-DC Converter for Handheld Applications Literature Number: SNVS464B LM3678 High-Performance, Miniature 1.5A Step-Down DCDC Converter for Handheld Applications General Description Features The LM3678 step-down DC-DC converter is optimized for powering low voltage circuits from a single Li-Ion cell battery and input voltage rails from 2.5V to 5.5V. It provides up to 1.5A load current, over the entire input voltage range. LM3678 offers a 0.8V/1.2V option. One of the pair of voltages is set through the VSELECT pin. LM3678 operates in PWM mode with a fixed frequency of 3.3MHz. Internal synchronous rectification provides high efficiency during PWM mode operation. In shutdown mode, the device turns off and reduces battery consumption to 0.01A (typ). The LM3678 is available in a 3mm x 3mm LLP-10 package. A high switching frequency of 3.3MHz (typ.) allows use of tiny surface-mount components. Only three external surfacemount components, an inductor and two ceramic capacitors, are required (solution size less than 33 mm2). For voltages other than the voltage shown, please refer to ordering information section or contact National Semiconductor. Typical Application Circuit VOUT = 0.8V/1.2V VIN = 2.5V to 5.5V 1.5A maximum load capability 3.3MHz PWM fixed switching frequency (typ.) allows the use of 1H inductor +/- 3% DC output voltage precision 0.01A typical shutdown current Internal synchronous rectification for high efficiency Internal soft start Current overload and thermal shutdown protection Applications PDAs and Smart Phones Personal Media Players W-LAN USB Modem Applications Digital still cameras Portable Hard disk drives Efficiency vs. Output Current ( VOUT = 1.2V) 20204501 Note: VSEL H = 1.2V, VSEL L = 0.8V 20204504 FIGURE 1. (c) 2009 National Semiconductor Corporation 202045 www.national.com LM3678 High-Performance, Miniature 1.5A Step-Down DC-DC Converter for Handheld Applications January 8, 2009 LM3678 Functional Block Diagram 20204505 FIGURE 2. LM3678 Block Diagram www.national.com 2 LM3678 Connection Diagram and Package Mark Information 20204503 20204502 Bottom View Top View Pin Descriptions Pin # Name Description 1 GND Power Ground pin. 2 GND Analog Ground Pin 3 SW Switching node connection to the internal PFET switch and NFET synchronous rectifier 4 VDD Analog supply input. Connect to the input filter capacitor (Figure 1). 5 VDD Power supply Input. Connect to the input filter capacitor (Figure 1). 6 VSELECT 7 PGOOD 8 PWM 9 EN Enable pin. The device is in shutdown mode when voltage to this pin is <0.4V and enabled when >1.0V. Do not leave this pin floating. 10 FB Feedback analog input. Connect directly to the output filter capacitor for fixed voltage versions. DAP DAP Output voltage select ( For example) VSELECT = LOW, VOUT = 0.8V VSELECT = HIGH , VOUT = 1.2V Power Good Flag. This commom drain logic output is pulled to ground when the output voltage is not within +/-7.5% of regulation. Connect PWM pin to VIN. Die Attach Pad, connect the DAP to GND on PCB layout to enhance thermal performance. It should not be used as a primary ground connection. Ordering Information Voltage Option 0.8V/1.2V Order Number Package Marking Supplied As LM3678SDE-1.2 S021B 250 units, Tape-and-Reel LM3678SD-1.2 S021B 1000 units, Tape-and-Reel LM3678SDX-1.2 S021B 4500 units, Tape-and-Reel 3 www.national.com LM3678 Storage Temperature Range Maximum Lead Temperature (Soldering, 10 sec.) Absolute Maximum Ratings (Note 1) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. VIN Pin: Voltage to GND EN Pin: FB, SW Pin: Continuous Power Dissipation (Note 3) Junction Temperature (TJ-MAX) Operating Ratings -0.2V to 6.0V -0.2V to 6.0V (GND-0.2V) to (VIN + 0.2V) Internally Limited -65C to +150C 260C (Notes 1, 2) Input Voltage Range 2.5V to 5.5V Recommended Load Current 0mA to 1.5A Junction Temperature (TJ) Range -30C to +125C Ambient Temperature (TA) Range (Note -30C to +85C 4) +150C Thermal Properties Junction-to-Ambient Thermal Resistance (JA) (LLP-10) for 4 layer board (Note 5) 49.8C/W Electrical Characteristics (Notes 2, 6, 8) Limits in standard typeface are for TJ = 25C. Limits in boldface type apply over the full operating ambient temperature range (-30C TA +85C). Unless otherwise noted, specifications apply to the LM3678 Typical Application Circuit (pg. 1) with VIN = EN = 3.6V Symbol Parameter Condition Min Typ Max Units +3 % VFB Feedback Voltage VSELECT = Low & High VREF Internal Reference Voltage (Note 7) 0.5 RDSON (P) Pin-Pin Resistance for PFET VIN= VGS= 3.6V 150 200 m RDSON (N) Pin-Pin Resistance for NFET VIN= VGS= 3.6V 110 150 m ILIM Switch Peak Current Limit Open loop 2.15 2.4 A ISHDN Shutdown Supply Current EN = 0V 1 A VIH Logic High Input for EN & VSELECT VIN = 3.6V VIL Logic Low Input for EN & VSELECT VIN = 3.6V IEN Enable (EN) Input Current FOSC Internal Oscillator Frequency PWM Mode -3 1.9 V V 1.2 V 0.4 2.7 0.01 1 A 3.3 3.6 MHz Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings are conditions under which operation of the device is guaranteed. Operating Ratings do not imply guaranteed performance limits. For guaranteed performance limits and associated test conditions, see the Electrical Characteristics tables. Note 2: All voltages are with respect to the potential at the GND pin. Note 3: Internal thermal shutdown circuitry protects the device from permanent damage. Thermal shutdown engages at TJ= 150C (typ.) and disengages at TJ= 130C (typ.). Note 4: In Applications where high power dissipation and/or poor package resistance is present, the maximum ambient temperature may have to be derated. Maximum ambient temperature (TA-MAX) is dependent on the maximum operating junction temperature (TJ-MAX), the maximum power dissipation of the device in the application (PD-MAX) and the junction to ambient thermal resistance of the package (JA) in the application, as given by the following equation: TA-MAX= TJ-MAX - (JAx PD-MAX). Note 5: Junction to ambient thermal resistance is highly application and board layout dependent. In applications where high power dissipation exists, special care must be given to thermal dissipation issues in board design. Note 6: Refer to datasheet curves for closed loop data and its variation with regards to supply voltage and temperature. Electrical Characteristic table reflects open loop data (FB=0V and current drawn from SW pin ramped up until cycle by cycle current limit is activated). Closed loop current limit is the peak inductor current measured in the application circuit by increasing output current until output voltage drops by 10%. Note 7: Min and Max limits are guaranteed by design, test or statistical analysis. Typical numbers are not guaranteed, but do represent the most likely norm. Note 8: The parameters in the electrical characteristic table are tested at VIN= 3.6V unless otherwise specified. For performance over the input voltage range refer to datasheet curves. www.national.com 4 LM3678SD, Circuit of Figure 1, VIN= 3.6V, VOUT= 1.2V, CIN = 10F, COUT = 22F, and TA= 25C, unless otherwise noted. Quiescent Supply Current vs. Temperature Switching Frequency vs. Temperature 20204533 20204535 NFET_ RDSON vs. Temperature PFET_RDSON vs. Temperature 20204536 20204537 Efficiency PWM Mode vs. ILOAD (0.8V) ILIMIT vs. Temperature (Open Loop) 20204522 20204538 5 www.national.com LM3678 Typical Performance Characteristics LM3678 Efficiency PWM Mode vs. ILOAD (1.2V) Line Transient Response (VOUT = 0.8V, LOAD = 500mA) 20204552 20204523 Line Transient Response (VOUT = 1.2V, LOAD = 500mA) Load Transient Response (VIN = 3.6V, VOUT = 1.2V, Load Step 0 500mA) 20204553 20204513 Load Transient Response (VIN = 3.6V, VOUT = 0.8V, Load Step 0 500mA) Load Transient Response (VIN = 3.6V, VOUT = 0.8V, Load Step 500mA 1A) 20204515 20204514 www.national.com 6 LM3678 Load Transient Response (VIN = 3.6V, VOUT = 1.2V, Load Step 500mA 1A) VSELECT Transient Response (VIN = 3.6V, LOAD = 500mA) 20204541 20204520 VSELECT Transient Response (VIN = 3.6V, No LOAD) VSELECT Transient Response (VIN = 3.6V, LOAD = 1A) 20204547 20204542 Start Up (VIN = 3.6V, VOUT = 1.2V, LOAD = 1A) Start Up (VIN = 3.6V, VOUT = 1.2V, LOAD = 500mA) 20204550 20204551 7 www.national.com LM3678 Switching Waveform (VOUT = 1.2V, LOAD = 1A) 20204556 www.national.com 8 DEVICE INFORMATION The LM3678, a high efficiency step down DC-DC switching buck converter, delivers a constant voltage from a single LiIon battery and input voltage rails from 2.5V to 5.5V to portable devices such as cell phones and PDAs. Using a voltage mode architecture with synchronous rectification, the LM3678 has the ability to deliver up to 1.5A depending on the input voltage, output voltage, ambient temperature and the inductor chosen. Additional features include soft-start, under voltage protection, current overload protection, and thermal shutdown protection. As shown in Figure 1, only three external power components are required for implementation. The part uses an internal reference voltage of 0.5V. It is recommended to keep the part in shutdown until the input voltage is 2.5V or higher. 20204555 CIRCUIT OPERATION During the first portion of each switching cycle, the control block in the LM3678 turns on the internal PFET switch. This allows current to flow from the input through the inductor to the output filter capacitor and load. The inductor limits the current to a ramp with a slope of (VIN-VOUT)/L, by storing energy in a magnetic field. During the second portion of each cycle, the controller turns the PFET switch off, blocking current flow from the input, and then turns the NFET synchronous rectifier on. The inductor draws current from ground through the NFET to the output filter capacitor and load, which ramps the inductor current down with a slope of - VOUT/L. The output filter stores charge when the inductor current is high, and releases it when inductor current is low, smoothing the voltage across the load. The output voltage is regulated by modulating the PFET switch on time to control the average current sent to the load. The effect is identical to sending a duty-cycle modulated rectangular wave formed by the switch and synchronous rectifier at the SW pin to a low-pass filter formed by the inductor and output filter capacitor. The output voltage is equal to the average voltage at the SW pin. FIGURE 3. Typical PWM Operation INTERNAL SYNCHRONOUS RECTIFICATION The LM3678 uses an internal NFET as a synchronous rectifier to reduce rectifier forward voltage drop and associated power loss. Synchronous rectification provides a significant improvement in efficiency whenever the output voltage is relatively low compared to the voltage drop across an ordinary rectifier diode. CURRENT LIMITING A current limit feature allows the LM3678 to protect itself and external components during overload conditions by implementing current limiting with an internal comparator that trips at 2.15A (typ). If the output is shorted to ground the device enters a timed current limit mode where the NFET is turned on for a longer duration until the inductor current falls below a low threshold. This allows the inductor current more time to decay, thereby preventing runaway. SHUTDOWN MODE Setting the EN input pin low (<0.4V) places the LM3678 in shutdown mode. During shutdown the PFET switch, NFET switch, reference, control and bias circuitry of the LM3678 are turned off. Setting EN high (>1.0V) enables normal operation. It is recommended to set EN pin low to turn off the LM3678 during system power up and undervoltage conditions when the supply is less than 2.5V. Do not leave the EN pin floating. PWM OPERATION During device operation the converter operates as a voltagemode controller with input voltage feed forward. This allows the converter to achieve good load and line regulation. The DC gain of the power stage is proportional to the input voltage. To eliminate this dependence, feed forward inversely proportional to the input voltage is introduced. The output voltage is regulated by switching at a constant frequency and then modulating the energy per cycle to control power to the load. At the beginning of each clock cycle the PFET switch is turned on and the inductor current ramps up until the comparator trips and the control logic turns off the switch. The current limit comparator can also turn off the switch in case the current limit of the PFET is exceeded. Then SOFT START The LM3678 has a soft-start circuit that limits in-rush current during start-up. During start-up the switch current limit is increased in steps. Soft start is activated only if EN goes from logic low to logic high after VIN reaches 2.5V. Soft start is implemented by increasing switch current limit in steps of 250mA, 500mA, 1A and 2A (typical switch current limit). The start-up time thereby depends on the output capacitor and load current demanded at start-up. 9 www.national.com LM3678 the NFET switch is turned on and the inductor current ramps down. The next cycle is initiated by the clock turning off the NFET and turning on the PFET. Operation Description LM3678 * VOUT: output voltage For a more conservative approach, a 1H inductor with a saturation current rating of at least 2.5A is recommended for most applications. Inductor Selection There are two main considerations when choosing an inductor; the inductor should not saturate, and the inductor current ripple should be small enough to achieve the desired output voltage ripple. Different saturation current rating specifications are followed by different manufacturers so attention must be given to details. Saturation current ratings are typically specified at 25C. However, ratings at the maximum ambient temperature of application should be requested from the manufacturer. Shielded inductors radiate less noise and should be preferred. There are two methods to choose the inductor saturation current rating. Input Capacitor Selection A ceramic input capacitor of 10uF, 6.3V is sufficient for most applications. Place the input capacitor as close as possible to the VIN pin of the device. A larger value may be used for improved input voltage filtering. Use X7R or X5R types; do not use Y5V. DC bias characteristics of ceramic capacitors must be considered when selecting case sizes like 0805 and 0603. The input filter capacitor supplies current to the PFET switch of the LM3678 in the first half of each cycle and reduces voltage ripple imposed on the input power source. A ceramic capacitor's low ESR provides the best noise filtering of the input voltage spikes due to this rapidly changing current. Select a capacitor with sufficient ripple current rating. The input current ripple can be calculated as: Method 1: The saturation current should be greater than the sum of the maximum load current and the worst case average to peak inductor current. This can be written as * * * * * IRIPPLE: average to peak inductor current IOUTMAX: maximum load current (1.5A) VIN: maximum input voltage in application L : minimum inductor value including worst case tolerances (30% drop can be considered for method 1) f : minimum switching frequency (2.7Mhz) TABLE 1. Suggest Inductors and Their Suppliers Model Vendor Dimensions LxWxH (mm) D.C.R (max) ISAT NR4012T1R0N Taiyo Yuden LPS4012-102L Coilcraft 4 x 4 x 1.2 60m 2.5A 3.9 x 3.9 x 1.2 100m 2.5A LPS4012-102L Coilcraft 3.9 x 3.9 x 1.8 40m 3.4A Voltage peak-to-peak ripple due to ESR can be expressed as follow: VPP-ESR = (2 * IRIPPLE) * RESR Because these two components are out of phase the rms (root mean squared) value can be used to get an approximate value of peak-to-peak ripple. The peak-to-peak ripple voltage rms value can be expressed as follow: Output Capacitor Selection A ceramic output capacitor of 22F, 6.3V is sufficient for most applications. Use X7R or X5R types; do not use Y5V. DC bias characteristics of ceramic capacitors must be considered when selecting case sizes like 0805 and 0603. DC bias characteristics vary from manufacturer to manufacturer and dc bias curves should be requested from them as part of the capacitor selection process. The output filter capacitor smooths out current flow from the inductor to the load, helps maintain a steady output voltage during transient load changes and reduces output voltage ripple. These capacitors must be selected with sufficient capacitance and sufficiently low ESR to perform these functions. The output voltage ripple is caused by the charging and discharging of the output capacitor and by the RESR and can be calculated as: Voltage peak-to-peak ripple due to capacitance can be expressed as follow: www.national.com Note that the output voltage ripple is dependent on the inductor current ripple and the equivalent series resistance of the output capacitor (RESR). The RESR is frequency dependent (as well as temperature dependent); make sure the value used for calculations is at the switching frequency of the part. 10 Model Type Vendor Voltage Rating Case Size Inch (mm) 10F for CIN GRM21BR60J106K Ceramic, X5R Murata 6.3V 0805 (2012) JMK212BJ106K Ceramic, X5R Taiyo-Yuden 6.3V 0805 (2012) C2012X5R0J106K Ceramic, X5R TDK 6.3V 0805 (2012) Ceramic, X5R Taiyo-Yuden 6.3V 0805 (2012) 22F for COUT JMK212BJ226MG reduces ground bounce at the LM3678 by giving it a lowimpedance ground connection. 4. Use wide traces between the power components and for power connections to the DC-DC converter circuit. This reduces voltage errors caused by resistive losses across the traces. 5. Route noise sensitive traces, such as the voltage feedback path, away from noisy traces between the power components. The voltage feedback trace must remain close to the LM3678 circuit and should be direct but should be routed opposite to noisy components. This reduces EMI radiated onto the DC-DC converter's own voltage feedback trace. A good approach is to route the feedback trace on another layer and to have a ground plane between the top layer and layer on which the feedback trace is routed. In the same manner for the adjustable part it is desired to have the feedback dividers on the bottom layer. 6. Place noise sensitive circuitry, such as radio IF blocks, away from the DC-DC converter, CMOS digital blocks and other noisy circuitry. Interference with noisesensitive circuitry in the system can be reduced through distance. For detailed layout information, refer to Application Note 1722 LM3678 Evaluation Board. In mobile phones, for example, a common practice is to place the DC-DC converter on one corner of the board, arrange the CMOS digital circuitry around it (since this also generates noise), and then place sensitive preamplifiers and IF stages on the diagonally opposing corner. Often, the sensitive circuitry is shielded with a metal pan and power to it is postregulated to reduce conducted noise, using low-dropout linear regulators. Board Layout Considerations PC board layout is an important part of DC-DC converter design. Poor board layout can disrupt the performance of a DCDC converter and surrounding circuitry by contributing to EMI, ground bounce, and resistive voltage loss in the traces. These can send erroneous signals to the DC-DC converter IC, resulting in poor regulation or instability. Good layout for the LM3678 can be implemented by following a few simple design rules below. 1. Place the LM3678, inductor and filter capacitors close together and make the traces short. The traces between these components carry relatively high switching currents and act as antennas. Following this rule reduces radiated noise. Special care must be given to place the input filter capacitor very close to the VIN and GND pin. 2. Arrange the components so that the switching current loops curl in the same direction. During the first half of each cycle, current flows from the input filter capacitor through the LM3678 and inductor to the output filter capacitor and back through ground, forming a current loop. In the second half of each cycle, current is pulled up from ground through the LM3678 by the inductor to the output filter capacitor and then back through ground forming a second current loop. Routing these loops so the current curls in the same direction prevents magnetic field reversal between the two half-cycles and reduces radiated noise. 3. Connect the ground pins of the LM3678 and filter capacitors together using generous component-side copper fill as a pseudo-ground plane. Then, connect this to the ground-plane (if one is used) with several vias. This reduces ground-plane noise by preventing the switching currents from circulating through the ground plane. It also 11 www.national.com LM3678 TABLE 2. Suggested Capacitors and Their Suppliers LM3678 Physical Dimensions inches (millimeters) unless otherwise noted Non Pullback LLP-10, 0.5mm Pitch NS Package Number SDA10A The dimensions for X1, X2, and X3 are as given: X1 = 3mm +/- 0.030mm X2 = 3mm +/- 0.030mm X3 = 0.800mm +/- 0.075mm www.national.com 12 LM3678 Notes 13 www.national.com LM3678 High-Performance, Miniature 1.5A Step-Down DC-DC Converter for Handheld Applications Notes For more National Semiconductor product information and proven design tools, visit the following Web sites at: Products Design Support Amplifiers www.national.com/amplifiers WEBENCH(R) Tools www.national.com/webench Audio www.national.com/audio App Notes www.national.com/appnotes Clock and Timing www.national.com/timing Reference Designs www.national.com/refdesigns Data Converters www.national.com/adc Samples www.national.com/samples Interface www.national.com/interface Eval Boards www.national.com/evalboards LVDS www.national.com/lvds Packaging www.national.com/packaging Power Management www.national.com/power Green Compliance www.national.com/quality/green Switching Regulators www.national.com/switchers Distributors www.national.com/contacts LDOs www.national.com/ldo Quality and Reliability www.national.com/quality LED Lighting www.national.com/led Feedback/Support www.national.com/feedback Voltage Reference www.national.com/vref Design Made Easy www.national.com/easy PowerWise(R) Solutions www.national.com/powerwise Solutions www.national.com/solutions Serial Digital Interface (SDI) www.national.com/sdi Mil/Aero www.national.com/milaero Temperature Sensors www.national.com/tempsensors Solar Magic(R) www.national.com/solarmagic Wireless (PLL/VCO) www.national.com/wireless Analog University(R) www.national.com/AU THE CONTENTS OF THIS DOCUMENT ARE PROVIDED IN CONNECTION WITH NATIONAL SEMICONDUCTOR CORPORATION ("NATIONAL") PRODUCTS. NATIONAL MAKES NO REPRESENTATIONS OR WARRANTIES WITH RESPECT TO THE ACCURACY OR COMPLETENESS OF THE CONTENTS OF THIS PUBLICATION AND RESERVES THE RIGHT TO MAKE CHANGES TO SPECIFICATIONS AND PRODUCT DESCRIPTIONS AT ANY TIME WITHOUT NOTICE. NO LICENSE, WHETHER EXPRESS, IMPLIED, ARISING BY ESTOPPEL OR OTHERWISE, TO ANY INTELLECTUAL PROPERTY RIGHTS IS GRANTED BY THIS DOCUMENT. TESTING AND OTHER QUALITY CONTROLS ARE USED TO THE EXTENT NATIONAL DEEMS NECESSARY TO SUPPORT NATIONAL'S PRODUCT WARRANTY. EXCEPT WHERE MANDATED BY GOVERNMENT REQUIREMENTS, TESTING OF ALL PARAMETERS OF EACH PRODUCT IS NOT NECESSARILY PERFORMED. NATIONAL ASSUMES NO LIABILITY FOR APPLICATIONS ASSISTANCE OR BUYER PRODUCT DESIGN. BUYERS ARE RESPONSIBLE FOR THEIR PRODUCTS AND APPLICATIONS USING NATIONAL COMPONENTS. PRIOR TO USING OR DISTRIBUTING ANY PRODUCTS THAT INCLUDE NATIONAL COMPONENTS, BUYERS SHOULD PROVIDE ADEQUATE DESIGN, TESTING AND OPERATING SAFEGUARDS. EXCEPT AS PROVIDED IN NATIONAL'S TERMS AND CONDITIONS OF SALE FOR SUCH PRODUCTS, NATIONAL ASSUMES NO LIABILITY WHATSOEVER, AND NATIONAL DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE SALE AND/OR USE OF NATIONAL PRODUCTS INCLUDING LIABILITY OR WARRANTIES RELATING TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. LIFE SUPPORT POLICY NATIONAL'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF THE CHIEF EXECUTIVE OFFICER AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b) support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness. National Semiconductor and the National Semiconductor logo are registered trademarks of National Semiconductor Corporation. All other brand or product names may be trademarks or registered trademarks of their respective holders. Copyright(c) 2009 National Semiconductor Corporation For the most current product information visit us at www.national.com National Semiconductor Americas Technical Support Center Email: support@nsc.com Tel: 1-800-272-9959 www.national.com National Semiconductor Europe Technical Support Center Email: europe.support@nsc.com German Tel: +49 (0) 180 5010 771 English Tel: +44 (0) 870 850 4288 National Semiconductor Asia Pacific Technical Support Center Email: ap.support@nsc.com National Semiconductor Japan Technical Support Center Email: jpn.feedback@nsc.com IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP(R) Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2011, Texas Instruments Incorporated