TGL41-110A-E3/96 - Vishay [General Semiconductor]

TGL41-6.8A thru TGL41-200A

www.vishay.com Vishay General Semiconductor

Revision: 13-Mar-12 1Document Number: 88403

For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

TRANSZorb® Transient Voltage Suppressors

FEATURES

• Plastic MELF package

• Ideal for automated placement

• Glass passivated chip junction

• Available in uni-directional polarity only

• 400 W peak pulse power capability with a

10/1000 μs waveform, repetitive rate (duty

cycle): 0.01 %

• Excellent clamping capability

• Very fast response time

• Low incremental surge resistance

• Meets MSL level 1, per J-STD-020, LF maximum peak of

250 °C

• Material categorization: For definitions of compliance

please see www.vishay.com/doc?99912

TYPICAL APPLICATIONS

Use in sensitive electronics protection against voltage

transients induced by inductive load switching and lighting

on ICs, MOSFET, signal lines of sensor units for consumer,

computer, industrial, and telecommunication.

MECHANICAL DATA

Case: DO-213AB (GL41)

Molding compound meets UL 94 V-0 flammability rating

Base P/N-E3 - RoHS compliant, commercial grade

Terminals: Matte tin plated leads, solderable per

J-STD-002 and JESD 22-B102

E3 suffix meets JESD 201 class 1A whisker test

Polarity: Blue band denotes the cathode which is positive

with respect to the anode under normal TVS operation

Notes

(1) Non-repetitive current pulse, per fig. 3 and derated above TA = 25 °C per fig. 2. Rating is 200 W above 91 V

(2) Measured at 8.3 ms single half sine-wave or equivalent square wave duty cycle = 4 pulses per minute maximum

PRIMARY CHARACTERISTICS

VBR 6.8 V to 200 V

PPPM 400 W, 200 W

PD 1.0 W

IFSM 40 A

TJ max. 150 °C

DO-213AB (GL41)

MAXIMUM RATINGS (TA = 25 °C unless otherwise noted)

PARAMETER SYMBOL VALUE UNIT

Peak pulse power dissipation with a 10/1000 μs waveform (1) (fig. 1) PPPM 400 W

Power dissipation on infinite heatsink at TL = 75 °C PD1.0 W

Peak pulse current with a 10/1000 μs waveform (1) (fig. 3) IPPM See next table A

Peak forward surge current, 8.3 ms half sine-wave uni-directional only (2) IFSM 40 A

Maximum instantaneous forward voltage at 25 A for uni-directional only VF3.5 V

Operating junction and storage temperature range TJ, TSTG - 55 to 150 °C

TGL41-6.8A thru TGL41-200A

www.vishay.com Vishay General Semiconductor

Revision: 13-Mar-12 2Document Number: 88403

For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Notes

(1) Pulse test: tp  50 ms

(2) Surge current waveform per fig. 3 and derate per fig. 2

(2) All terms and symbols are consistent with ANSI/IEEE C62.35

ELECTRICAL CHARACTERISTICS (TA = 25 °C unless otherwise noted)

DEVICE

TYPE

BREAKDOWN

VOLTAGE

VBR (1)

(V)

TEST

CURRENT

(mA)

STAND-OFF

VOLTAGE

VWM

(V)

MAXIMUM

REVERSE

LEAKAGE

AT VWM ID

(μA)

MAXIMUM

PEAK

PULSE

CURRENT

IPPM (2)

(A)

MAXIMUM

CLAMPING

VOLTAGE

AT IPPM

VC (V)

MAXIMUM

TEMPERATURE

COEFFICENT

OF VBR

(%/°C)

MIN. MAX.

TGL41-6.8A 6.45 7.14 10 5.80 1000 38.1 10.5 0.060

TGL41-7.5A 7.13 7.88 10 6.40 500 35.4 11.3 0.064

TGL41-8.2A 7.79 8.61 10 7.02 200 33.1 12.1 0.068

TGL41-9.1A 8.65 9.55 1.0 7.78 50.0 29.9 13.4 0.071

TGL41-10A 9.5 10.5 1.0 8.55 10.0 27.6 14.5 0.076

TGL41-11A 10.5 11.6 1.0 9.40 5.0 25.6 15.6 0.078

TGL41-12A 11.4 12.6 1.0 10.2 5.0 24.0 16.7 0.081

TGL41-13A 12.4 13.7 1.0 11.1 5.0 22.0 18.2 0.084

TGL41-15A 14.3 15.8 1.0 12.8 5.0 18.9 21.2 0.087

TGL41-16A 15.2 16.8 1.0 13.6 5.0 17.8 22.5 0.089

TGL41-18A 17.1 18.9 1.0 15.3 5.0 15.9 25.2 0.091

TGL41-20A 19.0 21.0 1.0 17.1 5.0 14.4 27.7 0.093

TGL41-22A 20.9 23.1 1.0 18.8 5.0 13.1 30.6 0.095

TGL41-24A 22.8 25.2 1.0 20.5 5.0 12.0 33.2 0.097

TGL41-27A 25.7 28.4 1.0 23.1 5.0 10.7 37.5 0.099

TGL41-30A 28.5 31.5 1.0 25.6 5.0 9.7 41.4 0.100

TGL41-33A 31.4 34.7 1.0 28.2 5.0 8.8 45.7 0.101

TGL41-36A 34.2 37.8 1.0 30.8 5.0 8.0 49.9 0.102

TGL41-39A 37.1 41.0 1.0 33.3 5.0 7.4 53.9 0.103

TGL41-43A 40.9 45.2 1.0 36.8 5.0 6.7 59.3 0.104

TGL41-47A 44.7 49.4 1.0 40.2 5.0 6.2 64.8 0.104

TGL41-51A 48.5 53.6 1.0 43.6 5.0 5.7 70.1 0.105

TGL41-56A 53.2 58.8 1.0 47.8 5.0 5.2 77.0 0.106

TGL41-62A 58.9 65.1 1.0 53.0 5.0 4.7 85.0 0.107

TGL41-68A 64.6 71.4 1.0 58.1 5.0 4.3 92.0 0.107

TGL41-75A 71.3 78.8 1.0 64.1 5.0 3.9 103 0.108

TGL41-82A 77.9 86.1 1.0 70.1 5.0 3.5 113 0.108

TGL41-91A 86.5 95.5 1.0 77.8 5.0 3.2 125 0.109

TGL41-100A 95.0 105 1.0 85.5 5.0 1.46 137 0.109

TGL41-110A 105 116 1.0 94.0 5.0 1.32 152 0.110

TGL41-120A 114 126 1.0 102 5.0 1.21 165 0.110

TGL41-130A 124 137 1.0 111 5.0 1.12 179 0.110

TGL41-150A 143 158 1.0 128 5.0 0.97 207 0.111

TGL41-160A 152 168 1.0 136 5.0 0.91 219 0.111

TGL41-170A 162 179 1.0 145 5.0 0.85 234 0.111

TGL41-180A 171 189 1.0 154 5.0 0.81 246 0.111

TGL41-200A 190 210 1.0 171 5.0 0.73 274 0.111

ORDERING INFORMATION (Example)

PREFERRED PIN UNIT WEIGHT (g) PREFERRED PACKAGE CODE BASE QUANTITY DELIVERY MODE

TGL41-6.8A-E3/96 0.134 96 1500 7" diameter plastic tape and reel

TGL41-6.8A-E3/97 0.134 97 5000 13" diameter plastic tape and reel

TGL41-6.8A thru TGL41-200A

www.vishay.com Vishay General Semiconductor

Revision: 13-Mar-12 3Document Number: 88403

For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

RATINGS AND CHARACTERISTICS CURVES (TA = 25 °C unless otherwise noted)

Fig. 1 - Peak Pulse Power Rating Curve

Fig. 2 - Pulse Power or Current vs. Initial Junction Temperature

Fig. 3 - Pulse Waveform

Fig. 4 - Typical Junction Capacitance

Fig. 5 - Power Derating Curve

Fig. 6 - Maximum Non-Repetitive Peak Forward Surge Current

Uni-Directional Only

td - Pulse Width

100

0.1

PPM

- Peak Pulse Power (kW)

0.1 µs 1.0 µs 10 µs 100 µs 1.0 ms 10 ms

TGL41-100 TGL200A

TGL41-6.8 TGL91A

Non-Repetitive Pulse

Waveform shown in Fig. 3

TA = 25 °C

TJ - Initial Temerature (°C)

100

Peak Pulse Power (P

) or Current (I

)

Derating in Percentace (%)

02550 100 150 200

75 125 175

t - Time (ms)

150

0 2.0 4.0

PPM

- Peak Pulse Current, % I

RSM

100

1.0 3.0

Peak Value

IPPM

10/1000 µs Waveform

as defined by R.E.A.

Half Value -

IPPM

IPP

TJ = 25 °C

Pulse Width (td)

is defined as the Point

where the Peak Current

decays to 50 % of IPPM

tr = 10 µs

Measured at Stand-Off

Voltage VWM

- Breakdown Voltage (V)

10 000

1000

100

- Junction Capacitance (pF)

1 10 100 1000

Uni-Directional

Measured at

Zero Bias

TJ = 25 °C

f = 1.0 MHz

Vsig = 50 mVp-p

TL - Lead Temerature (°C)

1.00

0.50

0.25

- Power Dissipation (W)

02550 100 150 200

0.75

75 125 175

Number of Cycles at 60 Hz

1100

Peak Forward Surge Current (A)

TJ = TJ Max.

8.3 ms Single Half Sine-Wave

TGL41-6.8A thru TGL41-200A

www.vishay.com Vishay General Semiconductor

Revision: 13-Mar-12 4Document Number: 88403

For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com

THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT

ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

PACKAGE OUTLINE DIMENSIONS in inches (millimeters)

D1 =

0.105

0.095

(2.67)

(2.41)

+ 0

- 0.008 (0.20)

DO-213AB (GL41)

Solderable Ends

Band D2 = D1

Band Denotes Type and Positive End (Cathode)

0.138 (3.5)

MAX.

0.049 (1.25)

MIN.

0.118 (3.0)

MIN.

0.238 (6.0)

REF.

Mounting Pad Layout

0.022 (0.56)

0.018 (0.46)

0.022 (0.56)

0.018 (0.46)

0.205 (5.2)

0.185 (4.7)

Legal Disclaimer Notice

www.vishay.com Vishay

Revision: 12-Mar-12 1Document Number: 91000

Disclaimer

ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE

RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.

Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,

“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other

disclosure relating to any product.

Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or

the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all

liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,

consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular

purpose, non-infringement and merchantability.

Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical

requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements

about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular

product with the properties described in the product specification is suitable for use in a particular application. Parameters

provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All

operating parameters, including typical parameters, must be validated for each customer application by the customer’s

technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,

including but not limited to the warranty expressed therein.

Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining

applications or for any other application in which the failure of the Vishay product could result in personal injury or death.

Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree

to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and

damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay

or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to

obtain written terms and conditions regarding products designed for such applications.

No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by

any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.

Material Category Policy

Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the

definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council

of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment

(EEE) - recast, unless otherwise specified as non-compliant.

Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that

all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.