0.5 mm Pitch, Board to Board Connector with Floating Structure FX20 Series X direction Y direction Floating range :0.6mm Floating range :0.60.8mm Features Enlarged view of the contact area 1. 0.5 mm pitch 2. Connection type: Right angle / Vertical 3. Pin counts : 20, 40, 60, 80, 100, 120 and 140 4. Floating range: 0.6 to 0.8 mm in the X direction and 0.6 mm in the Y direction 5. A double beam contact structure produces a highly reliable contact (Refer to the figure on the right) 6. Current capacity: 0.5 A per pin 7. Effective mating length of 1.5 mm Receptacle-side contact This connector utilizes a 1.5 mm effective mating length for signal contacts and provides a sufficient margin for its mating stroke. 8. No conductive trace surface is not specified 9. Contains the vacuum pick up area needed to allow automatic mounting 10.Self-aligning and self-guiding structure Header-side contact Built-in guide posts enable self-alignment and ensure a secure connection Stacking height chart Header Receptacle FX20-**S-0.5SV FX20-**P-0.5SV15 FX20-**P-0.5SV20 h=15mm h=20mm h=25mm h=30mm FX20-**S-0.5SV10 FX20-**S-0.5SH Floating range Right angle connection Right angle connection X direction 0.6mm 0.8mm Y direction 0.6mm 0.6mm FX20-**S-0.5SV10 FX20-**S-0.5SH FX20-**S-0.5SV h=15mm FX20-**P-0.5SV15 FX20-**P-0.5SV20 h=20mm h=25mm h=30mm Right angle connection Right angle connection 2014.3 1 FX20 Series0.5 mm Pitch, Board to Board Connector with Floating Structure Product Specifications Ratings Rated current 0.5A Rated voltage AC 50V Item Operating temperature range: -55 - 85C (Note 1) Storage temperature range: -10 - 60C (Note 2) Standards Condition 1. Contact resistance 70 mo max. 100 mA(DC or 1000Hz) 2. Insulation resistance 100 Mo min. 100 V DC. 3. Voltage proof No flashover or breakdown. Contact resistance : Variation from initial 4. Mechanical operation value 20 mo or less. No damage, crack and looseness of parts. 5. Vibration No electrical discontinuity of 1 s. No damage, crack and looseness of parts. 6. Shock 7. Damp heat (Steady state) 8. Rapid change of temperature Contact resistance : Variation from initial value 20 mo or less. Insulation resistance : 100Mo min. No damage, crack and looseness of parts. 150V AC for 1 min. 50 times insertions and extractions. Frequency: 10 to 55 to 10Hz, approx 5 min Single amplitude : 0.75mm, 10 cycles for 3 axial directions. 2 490m/s , duration of pulse 11ms at 3 times for 3 both axial directions. Exposed at 402C, 90~95%, 96h. Temperature: -55 +85C Time: 30 30 min. Under 5 cycles(relocation time to chamber: within 2~3min) Note 1: Includes temperature rise caused by current flow. Note 2: The term "storage" here refers to products stored for a long period prior to board mounting and use. Materials Part Material Header Receptacle Header Receptacle Insulator Contacts Metal Fitting Finish PA Black LCP Black Copper alloy Contact area: Gold plated Phosphor bronze Mounting area: Gold plated Brass Tin plated UL standard UL94V-0 UL94V-0 ------------------------------------------- Product Number Structure Refer to the charts below for determining specific part number characteristics. Please select connectors listed in this catalog when placing orders and be sure to check the latest delivery specifications at the time of ordering the product. Straight receptacle FX20 - 60 S - 0.5 SV 10 Straight header FX20 - 60 P - 0.5 SV 15 Right angle receptacle FX20 - 60 S - 0.5 SH Series name : FX20 Number (contacts): 2 Connector type S: Receptacle type P: Header type Contact pitch : 0.5mm Housing configuration : SV: Straight type Stacking height type Mating height [mm] = Height of the receptacle-side + Height of the header-side SH: Right angle type FX20 Series0.5 mm Pitch, Board to Board Connector with Floating Structure Straight receptacle FX20-**S-0.5SV A0.3 B0.3 2.70.2 6.80.3 Contact No. G Contact No. F C0.2 P=0.50.15 2 1. C 8.30.3 Contact No. 1 t=0.20.05xw=0.150.03 4.50.3 Contact No. E D0.3 (1.1) Polarization mark (1.1) 6.50.25 Unit: mm HRS No. Number of contacts A B C D E F G FX20-20S-0.5SV Part No. CL570-1114-7 20 17.4 16.4 4.5 12.65 10 11 20 FX20-40S-0.5SV CL570-1101-5 40 22.4 21.4 9.5 17.65 20 21 40 FX20-60S-0.5SV CL570-1102-8 60 27.4 26.4 14.5 22.65 30 31 60 FX20-80S-0.5SV CL570-1103-0 80 32.4 31.4 19.5 27.65 40 41 80 FX20-100S-0.5SV CL570-1104-3 100 37.4 36.4 24.5 32.65 50 51 100 FX20-120S-0.5SV CL570-1105-6 120 42.4 41.4 29.5 37.65 60 61 120 FX20-140S-0.5SV CL570-1106-9 140 47.4 46.4 34.5 42.65 70 71 140 A0.3 B0.3 C0.2 Contact No. G 6.80.3 2.70.2 FX20-**S-0.5SV10 Contact No. F P=0.50.15 C 2 1. Contact No. E Contact No. 1 t=0.30.05xw=0.150.03 60.3 18.30.3 D0.3 (1.1) Polarization mark (1.1) 6.50.25 Unit: mm Part No. HRS No. Number of contacts A B C D E F G FX20-20S-0.5SV10 CL570-1115-0 20 17.4 16.4 4.5 12.65 10 11 20 FX20-40S-0.5SV10 CL570-1107-1 40 22.4 21.4 9.5 17.65 20 21 40 FX20-60S-0.5SV10 CL570-1108-4 60 27.4 26.4 14.5 22.65 30 31 60 FX20-80S-0.5SV10 CL570-1109-7 80 32.4 31.4 19.5 27.65 40 41 80 FX20-100S-0.5SV10 CL570-1110-6 100 37.4 36.4 24.5 32.65 50 51 100 FX20-120S-0.5SV10 CL570-1111-9 120 42.4 41.4 29.5 37.65 60 61 120 FX20-140S-0.5SV10 CL570-1112-1 140 47.4 46.4 34.5 42.65 70 71 140 3 FX20 Series0.5 mm Pitch, Board to Board Connector with Floating Structure Contact No. F A0.3 C0.2 Contact No. G B0.3 P=0.50.15 Contact No. E C 1 FX20-**P-0.5SV15 8.70.2 2.70.2 Straight header Contact No. 1 t=0.150.03xw=0.20.05 D0.15 13.20.3 4.80.15 Polarization mark (0.85) 60.3 (0.85) 9.50.25 Unit: mm Part No. HRS No. Number of contacts A B C D E F G FX20-20P-0.5SV15 CL570-1014-2 20 17.4 16.4 4.5 10.4 10 11 20 FX20-40P-0.5SV15 CL570-1001-0 40 22.4 21.4 9.5 15.4 20 21 40 FX20-60P-0.5SV15 CL570-1002-3 60 27.4 26.4 14.5 20.4 30 31 60 CL570-1003-6 80 32.4 31.4 19.5 25.4 40 41 80 FX20-100P-0.5SV15 CL570-1004-9 100 37.4 36.4 24.5 30.4 50 51 100 FX20-120P-0.5SV15 CL570-1005-1 120 42.4 41.4 29.5 35.4 60 61 120 FX20-140P-0.5SV15 CL570-1006-4 140 47.4 46.4 34.5 40.4 70 71 140 Contact No.F A0.3 B0.3 C0.2 P=0.50.15 Contact No.G Contact No.E C 1 FX20-**P-0.5SV20 8.70.2 2.70.2 FX20-80P-0.5SV15 Contact No. 1 t=0.150.03xw=0.20.05 D0.15 18.20.3 110.3 4.80.15 (0.85) Polarization mark (0.85) 9.50.25 Unit: mm Part No. 4 HRS No. Number of contacts A B C D E F G FX20-20P-0.5SV20 CL570-1015-5 20 17.4 16.4 4.5 10.4 10 11 20 FX20-40P-0.5SV20 CL570-1007-7 40 22.4 21.4 9.5 15.4 20 21 40 FX20-60P-0.5SV20 CL570-1008-0 60 27.4 26.4 14.5 20.4 30 31 60 FX20-80P-0.5SV20 CL570-1009-2 80 32.4 31.4 19.5 25.4 40 41 80 FX20-100P-0.5SV20 CL570-1010-1 100 37.4 36.4 24.5 30.4 50 51 100 FX20-120P-0.5SV20 CL570-1011-4 120 42.4 41.4 29.5 35.4 60 61 120 FX20-140P-0.5SV20 CL570-1012-7 140 47.4 46.4 34.5 40.4 70 71 140 FX20 Series0.5 mm Pitch, Board to Board Connector with Floating Structure Right angle receptacle FX20-**S-0.5SH A0.2 P=0.50.15 W=0.150.03 (5.3) (2) 2.70.1 (2) 9.50.2 10.40.3 Vacuum pick up area Polarization mark (5) 7.150.3 B0.2 2.30.3 6.550.3 9.450.3 (0.2) C0.3 D0.2 P=0.50.15 W=0.150.03 Contact No. F Contact No. G Contact No. E Contact No. 1 Unit: mm Part No. HRS No. Number of contacts A B C D E F G FX20-20S-0.5SH CL570-1611-1 20 4.5 16.4 17.4 4.5 10 11 20 FX20-40S-0.5SH CL570-1601-8 40 9.5 21.4 22.4 9.5 20 21 40 FX20-60S-0.5SH CL570-1602-0 60 14.5 26.4 27.4 14.5 30 31 60 FX20-80S-0.5SH CL570-1603-3 80 19.5 31.4 32.4 19.5 40 41 80 FX20-100S-0.5SH CL570-1604-6 100 24.5 36.4 37.4 24.5 50 51 100 FX20-120S-0.5SH CL570-1605-9 120 29.5 41.4 42.4 29.5 60 61 120 FX20-140S-0.5SH CL570-1606-1 140 34.5 46.4 47.4 34.5 70 71 140 5 FX20 Series0.5 mm Pitch, Board to Board Connector with Floating Structure BRecommended PCB layout (PCB thickness: t= 1.6 mm/Stencil thickness: t= 0.15 mm, t= 0.12 mm 0 3.2 -0.1 Straight receptacle 3.20.05 FX20-**S-0.5SV FX20-**S-0.5SV10 7.1 +0.1 0 A0.03 P=0.50.03 Unit: mm SMT pad: 0.3 0.03 Stencil (t= 0.15): 0.25 0.03 Stencil (t= 0.12): 0.3 0.03 B0.05 30.05 30.05 ** A B 20 4.5 13.46 40 9.5 18.46 60 14.5 23.46 80 19.5 28.46 100 24.5 33.46 120 29.5 38.46 140 34.5 43.46 ** A 20 4.5 Straight header FX20-**P-0.5SV15 FX20-**P-0.5SV20 3.20.05 A0.03 10.1 +0.1 0 0 6.5 -0.1 P=0.50.03 SMT pad: 0.3 0.03 Stencil (t= 0.15): 0.25 0.03 Stencil (t= 0.12): 0.3 0.03 B0.05 30.05 30.05 Unit: mm B 13.46 40 9.5 18.46 60 14.5 23.46 80 19.5 28.46 100 24.5 33.46 120 29.5 38.46 140 34.5 43.46 Right angle receptacle FX20-**S-0.5SH B0.05 30.05 PCB edge (Mating side) 6 6.850.05 Contact No. (n/2+1) Contact No. (n/2) Contact No. n SMT pad: 0.3 0.03 Stencil (t= 0.15): 0.25 0.03 Stencil (t= 0.12): 0.3 0.03 0.1 0 Contact No.1 1max 3.20.05 P=0.50.03 10.050.05 1.7 0.1 0 A0.03 1.7 30.05 Unit: mm ** A B 20 4.5 13.46 40 9.5 18.46 60 14.5 23.46 80 19.5 28.46 100 24.5 33.46 120 29.5 38.46 140 34.5 43.46 FX20 Series0.5 mm Pitch, Board to Board Connector with Floating Structure BTray package drawing Straight receptacle ((#,* 8 6 E27 Part No. FX20-20S-0.5SV FX20-20S-0.5SV10 FX20-40S-0.5SV FX20-40S-0.5SV10 FX20-60S-0.5SV FX20-60S-0.5SV10 FX20-80S-0.5SV FX20-80S-0.5SV10 FX20-100S-0.5SV FX20-100S-0.5SV10 FX20-120S-0.5SV FX20-120S-0.5SV10 FX20-140S-0.5SV FX20-140S-0.5SV10 E2&,#* ''* &*,#* Unit: mm ('* Quantity A B C 90 42.5 30 240 80 40 35 245 70 50 60 50 45 225 60 47.5 46 230 50 57.5 52.5 210 50 51.5 55.5 222 37.5 225 ('* 8 6 Unit: mm Part No. FX20-20P-0.5SV15 FX20-20P-0.5SV20 FX20-40P-0.5SV15 FX20-40P-0.5SV20 FX20-60P-0.5SV15 FX20-60P-0.5SV20 FX20-80P-0.5SV15 FX20-80P-0.5SV20 FX20-100P-0.5SV15 FX20-100P-0.5SV20 FX20-120P-0.5SV15 FX20-120P-0.5SV20 FX20-140P-0.5SV15 FX20-140P-0.5SV20 E27 E2&,#* ''* &*,#* ((#,* Straight header Quantity A B C 90 42.5 30 240 80 40 35 245 70 50 60 50 45 225 60 47.5 46 230 50 57.5 52.5 210 50 51.5 55.5 222 37.5 225 Right angle receptacle (325) (C) (A) (225) (157.5) (P=17.5) (33.8) (P=B) Unit: mm Part No. FX20- 20S-0.5SH FX20- 40S-0.5SH FX20- 60S-0.5SH FX20- 80S-0.5SH FX20-100S-0.5SH FX20-120S-0.5SH FX20-140S-0.5SH Quantity 90 80 70 60 60 50 50 A B C 42.5 30 240 40 35 245 50 37.5 225 50 45 225 47.5 46 230 57.5 52.5 210 51.5 55.5 222 7 FX20 Series0.5 mm Pitch, Board to Board Connector with Floating Structure BRecommended Solder This temperature profile is based on the setting conditions shown below and is for reference only. For individual applications, the temperature profile may vary in accordance with the conditions. Please confirm the profile before mounting. (Peak temperature: 260C max.) 260 240 220 220 200 Temp.() 200 180 160 140 150 0 (90 to 120 sec) Pre-heating time (150 to 200C) <Applicable Conditions> Test PCB dimensions : 110 x 50 x 1.6 mm Material : Glass epoxy Solder composition : Sn- 3 Ag- 0.5 Cu Flux content : 11 wt% Stencil thickness : 0.12 mm, 0.15 mm Reflow count : 2 times Reflow area : 220C or more, 60 sec max. Preheating unit : 150 to 200C, 90 to 120 sec * The temperature profile may vary due to external conditions such as the type of cream solder, manufacturer, and board size. Please contact the solder manufacturer for their specifications. (60 sec or less) Soldering time (220C min.) BCleaning condition Organic solvent-based cleaning Solvent type IPA (Isopropyl alcohol) Room temperature cleaning Heated cleaning Water based cleaning When using water based cleaning agents (including terpene, and alkali saponifiers), pay special attention to how the cleaning agent will react to specific metals and plastics before selecting one of them. Various cleaning agent manufacturers publish reaction tables for their cleaning agents. Do not leave connectors with moisture remaining on them. Caution when washing The electrical performance may deteriorate if the flux or cleaning detergent is left on the connector after the cleaning. Check thoroughly to ensure that there is no residue left on any of the surfaces. BPrecautions Tolerance clearance on mating The effective contact length of each product is 1.5 mm. In the mated condition, the header and receptacle shall have a clearance or gap between them of no more than 1 mm. Receptacle-side connector Header-side connector 8 FX20 Series0.5 mm Pitch, Board to Board Connector with Floating Structure Using excessive force when mating these connectors may result in damage and alter their performance. Although they are designed with a prevention mechanism to resist incorrect insertion, do not forcibly mate them. Before mating the connector, confirm the connector polarity as shown below. C surface Mark (polarization mark) C surface Receptacle-side connector * Mate them so that both C surfaces or both marks on the connector outer surface are aligned. Header-side connector C surface Mark (polarization mark) C surface Provide another form of support to the PCB. This connector was not designed to be the main form of support. Mating and un-mating with excessive prying force or rotating force may result in damage to the connector or contact failure. If you have no choice but to mate and un-mate with prying force based on your usage environment, use a point as a pivot shown by mark in the figure below when you apply those forces. The point shall be a certain distance away from the connector end and has equal or higher height of the mating height. (Please refer to the guideline for details including the relationship between the pivot position and the connector position, and usage examples.) Minimum of 25 mm Minimum of 30 mm Stacking height or higher Stacking height or higher This connector has a floating structure, but the floating range may vary depending on the height of connector on the header side (which has a floating mechanism). Y direction (transverse direction) Y direction (transverse direction) X direction (longitudinal direction) X direction (longitudinal direction) Y direction (transverse direction) X direction (longitudinal direction) h=15mm Header-side FX20-**P-0.5SV15 FX20-**P-0.5SV20 FX20-**P-0.5SV15 FX20-**P-0.5SV20 FX20-**P-0.5SV15 FX20-**P-0.5SV20 h=30mm Receptacle-side FX20-**S-0.5SV FX20-**S-0.5SV10 FX20-**S-0.5SH Stack height 15mm 20mm 25mm 30mm ----------------------------- Right angle connection Floating range X direction (longitudinal direction) Y direction (transverse direction) 0.6mm 0.8mm 0.6mm 0.8mm 0.6mm 0.8mm 0.6mm 0.6mm 0.6mm 0.6mm 0.6mm 0.6mm 9 FX20 Series0.5 mm Pitch, Board to Board Connector with Floating Structure If the right angle type connector is positioned too far back from the recommended connector mounting position, the 1. 0m m M AX straight type connector will make contact with the PCB, and these may lead to damaged product or abnormal connections. The location of right angle type SMT pad should be set to within 1 mm from the edge of the PCB, and the mounting position should be set so that the clearance from the head of the connector to the edge of the PCB is 1.3 mm or less. 10 1.3mm MAX FX20 Series0.5 mm Pitch, Board to Board Connector with Floating Structure MEMO : 11 FX20 Series0.5 mm Pitch, Board to Board Connector with Floating Structure USA: HIROSE ELECTRIC (U.S.A.), INC. Headquarters 2688 Westhills Court, Simi Valley, CA 93065-6235 Phone : +1-805-522-7958 Fax : +1-805-522-3217 http://www.hiroseusa.com USA: HIROSE ELECTRIC (U.S.A.), INC. San Jose Office 3255 Scott Boulevard, Building 7, Suite 101 Santa Clara, CA 95054 Phone : +1-408-253-9640 Fax : +1-408-253-9641 http://www.hiroseusa.com USA: HIROSE ELECTRIC (U.S.A.), INC. Detroit Office (Automotive) 37677 Professional Center Drive, Suite #100C Livonia, MI 48154 Phone : +1-734-542-9963 Fax : +1-734-542-9964 http://www.hiroseusa.com THE NETHERLANDS: HIROSE ELECTRIC EUROPE B.V. Hogehillweg #8 1101 CC Amsterdam Z-O Phone : +31-20-6557460 Fax : +31-20-6557469 http://www.hiroseeurope.com GERMANY: HIROSE ELECTRIC EUROPE B.V. German Branch Herzog-Carl-Strasse 4 D-73760 Ostfildern (Scharnhauser Park) Phone : +49-711-4560-02-1 Fax : +49-711-4560-02-299 http://www.hirose.de UNITED KINGDOM: HIROSE ELECTRIC EUROPE B.V. UK Branch 22 Vincent Avenue, Crownhill Business Centre, Crownhill, Milton Keynes, MK8 0AB Phone : +44-1908-305750 Fax : +44-1908-305768 http://www.hirose.co.uk CHINA: HIROSE ELECTRIC TRADING (SHANGHAI) CO., LTD. 1601,Henderson Metropolitan,NO.300 ,East Nanjing Road,Huangpu District, Shanghai,China 200001 Phone : +86-21-6391-3355 Fax : +86-21-6391-3335 http://www.hirose-china.com.cn CHINA: HIROSE ELECTRIC TRADING (SHANGHAI) CO., LTD. Beijing Branch A1001, Ocean International Center, Building 56# East 4th Ring Middle Road, Chao Yang District, Beijing, 100025 Phone : +86-10-5165-9332 Fax : +86-10-5908-1381 http://www.hirose-china.com.cn CHINA: HIROSE ELECTRIC TECHNOLOGIES (SHENZHEN) CO., LTD. Room 09-13, 19/F, Office Tower Shun Hing Square, Di Wang Commercial Centre 5002, ShenNanDong Road, ShenZhen City, Guangdong Province, 518008 Phone : +86-755-8207-0851 Fax : +86-755-8207-0873 http://www.hirose-china.com.cn HONG KONG: HIROSE ELECTRIC HONGKONG TRADING CO., LTD. Room 1001, West Wing, Tsim Sha Tsui Centre, 66 Mody Road, Tsim Sha Tsui East, Kowloon, Hong Kong Phone : +852-2803-5338 Fax : +852-2591-6560 http://www.hirose-hongkong.com.hk TAIWAN: HIROSE ELECTRIC TAIWAN CO., LTD. 103 8F, No.87, Zhengzhou Rd., Taipei Phone : +886-2-2555-7377 Fax : +886-2-2555-7350 http://www.hirose-taiwan.com.tw KOREA: HIROSE KOREA CO., LTD. 1261-10, Jeoungwhang-Dong, Shihung-City, Kyunggi-Do 429-450 Phone : +82-31-496-7000,7124 Fax : +82-31-496-7100 http://www.hirose.co.kr INDIA: SINGAPORE: HIROSE ELECTRIC SINGAPORE PTE. LTD. HIROSE ELECTRIC SINGAPORE PTE. LTD. Bangalore Liaison office 10 Anson Road #26-1 International Plaza Unit No.03, Ground Floor, Explorer Building International Tech 079903 Park Whitefield Road, Bangalore 560066 Karnataka, India Phone : +65-6324-6113 Phone : +65-6324-6113 Fax : +65-6324-6123 Fax : +65-6324-6123 http://www.hirose-singapore.com.sg http://www.hirose-singapore.com.sg INDIA: HIROSE ELECTRIC SINGAPORE PTE. LTD Delhi Liaison Office Suite No. 606 5th Floor SB Tower 1A/1 Sector 16 A Filmcity Noida 201301 Uttar Pradesh-India Phone : +91-120-4804917 Fax : +91-120-4804949 http://www.hirose.com/sg/ MALAYSIA: HIROSE ELECTRIC SINGAPORE PTE. LTD (Representative office) 1-10-07, Suntech @ Penang Cybercity (1164),Lintang Mayang Pasir 3,11950, Bayan Baru, Penang, Malaysia. Phone : +604-619-2564 Fax : +604-619-2574 http://www.hirose.com/sg/ (R) 12 6-3,Nakagawa Chuoh-2-Chome,Tsuzuki-Ku,Yokohama-Shi 224-8540,JAPAN TEL: +81-45-620-3526 Fax: +81-45-591-3726 http://www.hirose.com http://www.hirose-connectors.com The characteristics and the specifications contained herein are for reference purpose. Please refer to the latest customer drawings prior to use. The contents of this catalog are current as of date of 3/2014. Contents are subject to change without notice for the purpose of improvements.