APL5501-32DC-TR - Anpec Electronics Corporation

Low IQ, Low Dropout 500mA Fixed Voltage Regulator

Rev. A.9 - May., 2003

APL5501/2/3

www.anpec.com.tw1

ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise

customers to obtain the latest version of relevant information to verify before placing orders.

Features

Design with an internal P-channel MOSFET pass

transistor, the APL5501/2/3 maintains a low supply

current, independent of the load current and dropout

voltage. Other features include reverse current

protection, thermal-shutdown protection, current limit

protection to ensure specified output current and con-

trolled short-circuit current. The APL5501/2/3 regu-

lator comes in a miniature SOT-23-5, SOT-89, SOT-

89-5, SOT-223, SO-8, TO-252 and TO-252-5

packages.

Applications

• Notebook Computer

• PDA or Portable Equipments

• Noise-Sensitive Instrumentation Systems

••

• Low Noise : 50µVRMS (100Hz to 100kHz)

••

• Low Quiescent Current : 50µA (No load)

••

• Low Dropout Voltage : 170mV (@500mA)

••

• Very low Shutdown Current : < 0.5uA

••

• Fixed Output Voltage : 1.3V ~ 3.4V

••

• Stable with 4.7uF Output Capacitor

••

• Stable with Aluminum , Tantalum or Ceramic

Capacitors .

••

• Reverse Current Protection

••

• No Protection Diodes Needed

••

• Built in Thermal Protection

••

• Built in Current Limit Protection

••

• Controlled Short Circuit Current : 150mA

••

• Fast Transient Response

••

• Short Setting Time

••

• SOT-23-5, SOT-89, SOT-89-5, SOT-223, SO-8

,TO-252 and TO-252-5 Packages

Pin Configuration

SOT-89 (Top View)

VIN GND VOUT

123

TAB is GND

SOT-89-5 (Top View)

SO-8 (Top View)

8IN

GND

SHDN BYP

GND

OUT

TO-252-5 (Top View)

General Description

The APL5501/2/3 is micropower, low noise, low drop-

out linear regulator. Operate from 2.7V to 6V input

voltage and deliver up to 500mA. Typical output noise

is just 50µVRMS with the addition of an external 0.1µF

bypass capacitor in BP pin and typical dropout volt-

age is only 170mV at 500mA loading . Designed for

use in battery-powered system, the low 50uA quies-

cent current makes it an ideal choice.

TO-252 (Top View)

GND

123

VOUT

VIN

GND

VOUT

123

SHDN

BP GND

OUT

GND

VIN

12345

TAB is GND

SHDN

SOT-23-5 (Top View)

5V IN

GND

SHDN BP

VOUT

APL5501

Rev. A.9 - May., 2003

APL5501/2/3

www.anpec.com.tw2

Product Name Marking Product Name Marking Product Name Marking

APL5501-13B 517X APL5502-13B 527X APL5503-13B 537X

APL5501-14B 518X APL5502-14B 528X APL5503-14B 538X

APL5501-15B 519X APL5502-15B 529X APL5503-15B 539X

APL5501-16B 51AX APL5502-16B 52AX APL5503-16B 53AX

APL5501-17B 51BX APL5502-17B 52BX APL5503-17B 53BX

APL5501-18B 51CX APL5502-18B 52CX APL5503-18B 53CX

APL5501-19B 51DX APL5502-19B 52DX APL5503-19B 53DX

APL5501-20B 51EX APL5502-20B 52EX APL5503-20B 53EX

APL5501-21B 51FX APL5502-21B 52FX APL5503-21B 53FX

APL5501-22B 51GX APL5502-22B 52GX APL5503-22B 53GX

APL5501-23B 51HX APL5502-23B 52HX APL5503-23B 53HX

APL5501-24B 51IX APL5502-24B 52IX APL5503-24B 53IX

APL5501-25B 51JX APL5502-25B 52JX APL5503-25B 53JX

APL5501-26B 51KX APL5502-26B 52KX APL5503-26B 53KX

APL5501-27B 51LX APL5502-27B 52LX APL5503-27B 53LX

Package Code

B : S O T-23-5 D : S O T-89 D 5 : SO T-89-5

U : TO -252 U 5 : TO -252-5 V : SO T-223

K : S O -8

Temp. Range

C : 0 to 70 C

Handling Code

TR : Tape & Reel

Voltage Code :

13 : 1.3V ~ 34 : 3.4V

APL5501/2/3 -

Handling Code

Temp. Range

Package Code

Voltage Code

APL5501/2/3

XXXXX

APL5501/2/3 - 13 U : XXXXX - Date Code , 13 - 1.3V

XXXXX - Date Code , 13 - 1.3V

APL5501/2/3

XXXXX13

APL5501/2/3 - 13 D/V/K :

Ordering and Marking Information

Pin Configuration (Cont.)

SOT-223 (Top View)

VOUT

GNDVIN

123

TAB is GND

APL5501 APL5502

SOT-89 (Top View)

GND VIN VOUT

123

TAB is VIN

VIN

GNDVOUT

123

TAB is GND

SOT-223 (Top View)

APL5503

VOUT

VIN

GND

123

TAB is VIN

SOT-223 (Top View)

APL5502

Marking Information

SOT-23-5 package

Rev. A.9 - May., 2003

APL5501/2/3

www.anpec.com.tw3

Product Name Marking Product Name Marking Product Name Marking

APL5501-28B 51MX APL5502-28B 52MX APL5503-28B 53MX

APL5501-29B 51NX APL5502-29B 52NX APL5503-29B 53NX

APL5501-30B 51OX APL5502-30B 52OX APL5503-30B 53OX

APL5501-31B 51PX APL5502-31B 52PX APL5503-31B 53PX

APL5501-32B 51QX APL5502-32B 52QX APL5503-32B 53QX

APL5501-33B 51RX APL5502-33B 52RX APL5503-33B 53RX

APL5501-34B 51SX APL5502-34B 52SX APL5503-34B 53SX

Pin Description

No. Name I/O Description

IN I Supply voltage input.

2 SHDN (Note1) I Shutdown control pin, low = off , high = normal .

3GND Ground pins of the circuitry, and all ground pins must be soldered to

PCB with proper power dissipation.

4BP

(Note1) O Bypass signal pin in fixed output type device

OUT O Output pin of the regulator.

Marking Information (Cont.)

SOT-23-5 package

Note1 : These pins do not exist in 3-pin package.

Symbol Parameter Rating Unit

VIN, VOUT Input Voltage or Out Voltage 5 V

SHDN Shutdown Control Pin 5V

RTH,JA Thermal Resistance – Junction to Ambient

SOT-89 : 180

SOT-223 : 135

SO-8 : 210

SOT-23-5 : 357

°C/W

PDPower Dissipation Internally Limited W

TJOperating Junction Temperature °C

Control Section 0 to 125

Power Transistor 0 to 150

TSTG Storage Temperature Range -65 to +150 °C

TLLead Temperature (Soldering, 10 second) 260 °C

Absolute Maximum Ratings

The last character “X” in the marking is for data code.

Rev. A.9 - May., 2003

APL5501/2/3

www.anpec.com.tw4

Electrical Characteristics

Unless otherwise noted these specifications apply over full temperature, VIN=3.6V, CIN=1µF, COUT=4.7µF,

SHDN=VIN, TJ=0 to 125°C. Typical values refer to TJ=25°C.

APL5501/2/3

Symbol Parameter Test Conditions Min. Typ. Max. Unit

VIN Input Voltage 2.7 6 V

VOUT Output Voltage VOUT+1.0V< VCC<6.0V, 0mA< IOUT < IMAX VOUT -2%VOUT VOUT +2%V

ILIMIT Circuit Current Limit VIN=4.3V 0.7 A

ISHORT Short Current VOUT=0V 200 mA

IOUT Load Current 500 mA

REGLINE Line Regulation VOUT+0.5V< VCC<6.0V, 0mA< IOUT < IMAX 410mV

REGLOAD Load Regulation VIN =VOUT+1.0V, 0mA< IOUT < IMAX 16mV

VDROP

Dropout Voltage(Note2)

(VOUT(Nominal)=3.0V

Version)

IOUT =500mA 170 300 mV

PSRR Ripple Rejection F≤1kHz, 1Vpp at VIN = VOUT+1.0V 55 65 dB

No load 50 100

IQQuiescent Current IOUT=500mA 370 450 µA

Shutdown Supply

Current(Note3)

Shutdown = low

IOUT=0, VCC =6.0V 0.01 1 µA

100Hz<f<100kHz, typical load,

CBP=0.01µF, COUT = 1µF50

Noise(Note3)

100Hz<f<100kHz, typical load,

CBP=0.1µF, COUT = 1µF40

µVrms

CBP=0.01µF, COUT=1µF, no load 7

Shutdown Recovery

Delay(Note3) CBP=0.1µF,COUT=1µF, no load 70 ms

OTS Over Temperature

Shutdown 150 °C

Over Temperature

Shutdown Hysteresis Hysteries 10 °C

Output Voltage

Temperature

Coefficient

50 ppm/°C

COUT Output Capacitor 4.2 4.7 5.2 µF

ESR 0.02 0.1 1 Ohm

Shutdown Input

Threshold(Note3) VOUT+1.0V< VIN <6.0V 0.4 0.7 1.6 V

ISHDN

Shutdown input Bias

current(Note3) VSHDN =VIN 0.01 100 nA

Input Reverse Leakage

current VOUT-VIN=0.1V 0.1 0.5 µA

Reverse Protection

Threshold 11 50 mV

Note 2 : Dropout voltage definition : VIN-VOUT when VOUT is 2% below the value of VOUT for VIN = VOUT + 0.5V

Note 3 : For 5-pin devices only.

Rev. A.9 - May., 2003

APL5501/2/3

www.anpec.com.tw5

Application Circuit

VOUT

VIN

GND

SHDN

VOUT

CIN

1uF

off

APL5501/2/3

INPUT

2.7V to 6V

0.1uF

CBP

COUT

4.7uF

Rev. A.9 - May., 2003

APL5501/2/3

www.anpec.com.tw6

0.5

1.5

2.5

3.5 4 4.5 5 5.5 6

0.5

1.5

2.5

3.5

0123456

100

150

200

250

300

350

0123456

100

150

200

250

300

350

400

0 150 300 450 600 750 900

Typical Characteristics

Input Voltage (V)

Current Limit (mA)

Ground Pin Current vs. Load Current (uA)

Output Current (mA)

Input Voltage (V)

Ground Pin Current vs. Load Current (uA)

Input Voltage (V)

Output Voltage (V)

APL5501/2/3-33

Input Voltage vs. Output VoltageGround Pin Current vs. Input Voltage

Current Limit vs. Input Voltage Ground Pin Current vs. Output Current

Rev. A.9 - May., 2003

APL5501/2/3

www.anpec.com.tw7

-100

-90

-80

-70

-60

-50

-40

-30

-20

-10

20 200k50 100 200 500 1k 2k 5k 10k 20k 50k 100k

0.4

0.5

0.6

0.7

0.8

0.9

3 3.5 4 4.5 5 5.5 6

-12

-10

-8

-6

-4

-2

00.511.522.53

100

150

200

250

0 150 300 450 600 750 900

Typical Characteristics

SHDN Threshold Voltage (V)

Input Voltage (V)

PSRR vs. Frequency

Frequency (HZ)

PSRR (dB)

IOUT =50mA

COUT=10uF

CBP=0.1uF

Output Current (uA)

Output Voltage (V)Output Current (mA)

Dropout Voltage (mV)

VIN=0V

VIN=0V VIN=4V

VIN=5V

APL5501/2/3-33

APL5501/2/3-33 APL5501/2/3-33

Dropout Voltage vs. Output Current Output Current vs. Output Voltage

APL5501/2/3-33

SHDN Threshold Voltage vs. Input Voltage

Rev. A.9 - May., 2003

APL5501/2/3

www.anpec.com.tw8

100

150

200

250

300

350

400

450

500

0 0.1 0.2 0.3 0.4

-100u

100u

-80u

60u

-40u

-20u

20u

40u

60u

80u

010m

2m 4m 6m 8m

Typical Characteristics

Output Noise

Time (s)

VOUT (50uV/div)

VIN=4.3V

IOUT =0mA

COUT=10uF

CBP=0.1uF

Output Noise vs. Bypass Capacitor

Output Noise (uV)

Bypass Capacitor (uF)

Time (1ms/div)

VOUT

vSHDN

Shutdown Exit Delay

Time (20ms/div)

VOUT

vSHDN

CBP=100nF

No Load

Shutdown Exit Delay

APL5501/2/3-33

3.3V

CBP=10nF

No Load

APL5501/2/3-33

Rev. A.9 - May., 2003

APL5501/2/3

www.anpec.com.tw9

0.001

0.01

0.1

0 150 300 450 600 750 900

VOUT

COUT=1µF

No Load

Typical Characteristics

Entering Shutdown

Time (200ms/div)

VOUT=3.3V

Region of Stable ESR vs. Load Current

Load Current (mA)

COUT ESR (Ω)

unstable

stable

APL5501/2/3-33

3.3V

3.25

3.27

3.29

3.31

3.33

3.35

-40 0 40 80 120

Temperature (°C )

Output Voltage (V)

APL5501/2/3-33

Output Voltage vs. Temperature

Time (40µs/div)

VOUT

VIN

Line-Transient Response

Output Voltage (20mV/div)

APL5901/2-33

Rev. A.9 - May., 2003

APL5501/2/3

www.anpec.com.tw10

COUT=1µF

VIN=VOUT+1V

Typical Characteristics

Time (10µs/div)

APL5501/2/3-33

IOUT=1mA~500mA

Output Voltage (50mV/div)

Load-Transient Response

VOUT

Rev. A.9 - May., 2003

APL5501/2/3

www.anpec.com.tw11

The minimum input-output voltage difference (dropout)

determines the lowest usable supply voltage. In bat-

tery-powered systems, this will determine the useful

end-of-life battery voltage. Because the APL5501/2/3

use a p-channel MOSFET pass transistor, the drop-

out voltage is a function of drain-to-source on-resis-

tance (RDS(ON)) multiplied by the load current.

The APL5501/2/3 load-transient response graphs in

typical characteristics show the transient response.

A step change in the load current from 0mA to 500mA

at 1us will cause a 100mV transient spike. Larger

output capacitor and lower ESR can reduce transient

spike.

Application Information

Capacitor Selection and Regulator

Stability

The APL5501/2/3 use at least a 1uF capacitor on the

input, and this capacitor can be Aluminum, Tantalum

or Ceramic capacitor. The input capacitor with larger

value and lower ESR provides better PSRR and line-

transient response. The output capacitor also can use

Aluminum, Tantalum or Ceramic capacitor, and a mini-

mum value of 1uF and ESR above 0.06Ω is

recommended. The curve of the stable region in typi-

cal characteristics shows the appropriate output ca-

pacitor ESR for different load current stable operation.

A larger output capacitor can reduce noise and im-

prove load-transient response, stability, and PSRR.

Note that some ceramic dielectrics exhibit large ca-

pacitance and ESR variation with temperature. When

using this capacitor, a minimum 10uF or more may

be required to ensure the stability at low temperature

operation. Use a bypass capacitor at BP pin for low

output nvise. Increasing the capacitance will slightly

decrease the output noise, but increase the start-up

time.

Load-Transient Considerations

Input-Output (Dropout)Voltage

Reverse Current Protection

The APL5501/2/3 have an internal reverse protection,

it does not need an external schottky diode to con-

nect the regulator input and output. If the output volt-

age is forced above the input voltage by more than

11mV, the IC will be shutdown and the ground pin

current is below 0.1uA.

Current Limit

The APL5501/2/3 have a current limit protection. The

ouptut voltage will drop close to zero volt, when load

current reaches the limit, and then the load current

will be limited at 150mA after output voltage is below

0.7V. When the load current back to the value where

limiting started, the output voltage and current will re-

turn to normal value. When output is shorted to

ground, the APL5501/2/3 will keep short circuit cur-

rent at 150mA .

Rev. A.9 - May., 2003

APL5501/2/3

www.anpec.com.tw12

Thermal protection limits total power dissipation in the

device. When the junction temperature exceeds

TJ=+150J, the thermal sensor generates a logic sig-

nal to turn off the pass transistor and allows IC to

cool. When the IC’s junction temperature is down by

10J, the thermal sensor will turn the pass transistor

on again, resulting in a pulsed output during continu-

ous thermal protection. Thermal protection is designed

to protect the APL5501/2/3 in the event of fault

conditions. For continuous operation, do not exceed

the absolute maximum junction temperature of

TJ=+150J.

Operating Region and Power Dis-

sipation

The thermal resistance of the case to circuit board,

and the rate of air flow all control the APL5501/2/3’s

maximum power dissipation. The power dissipation

across the device is PD = IOUT (VIN-VOUT) and the maxi-

mum power dissipation is:

PDMAX = (TJ-TA) / (?JC + ?CA)

where TJ-TA is the temperature difference between the

junction and ambient air, ?JC is the thermal resis-

tance of the package, and ?CA is the thermal resis-

tance through the printed circuit board, copper traces,

and other materials to the ambient air.

The GND pin of the APL5501/3 provide an electrical

connection to ground and channeling heat away. If

power dissipation is large, connect the GND pin to

ground using a large pad or ground plane, can im-

prove the problem of over heat of IC.

Thermal Protection

Rev. A.9 - May., 2003

APL5501/2/3

www.anpec.com.tw13

Packaging Information

SOT-23-5

E1 E

12 3

A2 A

A1 L 2 L

L 1

Millimeters Inches

Dim Min. Max. Min. Max.

A 0.95 1.45 0.037 0.057

A1 0.05 0.15 0.002 0.006

A2 0.90 1.30 0.035 0.051

D2.83.00

0.110 0.118

E2.63.00

0.102 0.118

E1 1.5 1.70 0.059 0.067

L 0.35 0.55 0.014 0.022

L1 0.20 BSC 0.008 BSC

L2 0.5 0.7 0.020 0.028

N5 5

α0°10°0°10°

Rev. A.9 - May., 2003

APL5501/2/3

www.anpec.com.tw14

Packaging Information

Millimeters Inches

Dim Min. Max. Min. Max.

A 1.35 1.75 0.053 0.069

A1 0.10 0.25 0.004 0.010

D 4.80 5.00 0.189 0.197

E 3.80 4.00 0.150 0.157

H 5.80 6.20 0.228 0.244

L 0.40 1.27 0.016 0.050

e1 0.33 0.51 0.013 0.020

e2 1.27BSC 0.50BSC

φ 18

°8°

e1 e2

0.015X45

0.004max.

SOP-8 pin ( Reference JEDEC Registration MS-012)

Rev. A.9 - May., 2003

APL5501/2/3

www.anpec.com.tw15

SOT-223( Reference JEDEC Registration SOT-223)

H E

Millimeters InchesDim

Min. Max. Min. Max.

A 1.50 1.80 0.06 0.07

A1 0.02 0.08

B 0.60 0.80 0.02 0.03

B1 2.90 3.10 0.11 0.12

c 0.28 0.32 0.01 0.01

D 6.30 6.70 0.25 0.26

E 3.30 3.70 0.13 0.15

e 2.3 BSC 0.09 BSC

e1 4.6 BSC 0.18 BSC

H 6.70 7.30 0.26 0.29

L 0.91 1.10 0.04 0.04

K 1.50 2.00 0.06 0.08

α0°10°0°10°

β13°13°

Packaging Information

Rev. A.9 - May., 2003

APL5501/2/3

www.anpec.com.tw16

Packaging Information

12 3

SOT-89 (Reference EIAJ ED-7500A Reg stration SC-62)

Millimeters Inches

Dim Min. Max. Min. Max.

A 1.40 1.60 0.055 0.063

B 0.40 0.56 0.016 0.022

B1 0.35 0.48 0.014 0.019

C 0.35 0.44 0.014 0.017

D 4.40 4.60 0.173 0.181

D1 1.35 1.83 0.053 0.072

e 1.50 BSC 0.059 BSC

e1 3.00 BSC 0.118 BSC

E 2.29 2.60 0.090 0.102

H 3.75 4.25 0.148 0.167

L 0.80 1.20 0.031 0.047

α10°10°

Rev. A.9 - May., 2003

APL5501/2/3

www.anpec.com.tw17

Packaging Information

SOT-89-5

Millimeters Inches

Dim Min. Max. Min. Max.

A 4.40 4.60 0.17 0.18

B 4.05 4.25 0.16 0.17

C 1.50 1.70 0.06 0.07

D 1.30 1.50 0.05 0.06

E 2.40 2.60 0.09 0.1

F 0.80 - 0.03 -

G 3.00 REF 0.12 REF

H 1.50 REF 0.06 REF

I 0.40 0.52 0.01 0.02

J 1.40 1.60 0.05 0.06

K 0.35 0.41 0.01 0.02

L 5 TYP 0.2 TYP

Rev. A.9 - May., 2003

APL5501/2/3

www.anpec.com.tw18

TO-252( Reference JEDEC Registration TO-252)

Millimeters Inches

Dim Min. Max. Min. Max.

A 2.18 2.39 0.086 0.094

A1 0.89 1.27 0.035 0.050

b 0.508 0.89 0.020 0.035

b2 5.207 5.461 0.205 0.215

C 0.46 0.58 0.018 0.023

C1 0.46 0.58 0.018 0.023

D 5.334 6.22 0.210 0.245

E 6.35 6.73 0.250 0.265

e1 3.96 5.18 0.156 0.204

H 9.398 10.41 0.370 0.410

L 0.51 0.020

L1 0.64 1.02 0.025 0.040

L2 0.89 2.032 0.035 0.080

Packaging Information

Rev. A.9 - May., 2003

APL5501/2/3

www.anpec.com.tw19

Packaging Information

TO-252-5

Millimeters Inches

Dim Min. Max. Min. Max.

A 6.40 6.80 0.25 0.26

B 5.20 5.50 0.20 0.21

C 6.80 7.20 0.26 0.27

D 2.20 2.80 0.08 0.11

P 1.27 REF 0.05 REF

S 0.50 0.80 0.02 0.03

H 2.20 2.40 0.08 0.09

J 0.45 0.55 0.01 0.02

K 0 0.15 0 0.006

L 0.90 1.50 0.03 0.06

M 5.40 5.80 0.21 0.22

Rev. A.9 - May., 2003

APL5501/2/3

www.anpec.com.tw20

Physical Specifications

Pre-heat temperature

183 C

Peak temperature

Time

temperature

Classification Reflow Profiles

Convection or IR/

Convection

VPR

Average ramp-up rate(183°C to Peak) 3°C/second max. 10 °C /second max.

Preheat temperature 125 ± 25°C) 120 seconds max

Temperature maintained above 183°C60 – 150 seconds

Time within 5°C of actual peak temperature 10 –20 seconds 60 seconds

Peak temperature range 220 +5/-0°C or 235 +5/-0°C 215-219°C or 235 +5/-0°C

Ramp-down rate 6 °C /second max. 10 °C /second max.

Time 25°C to peak temperature 6 minutes max.

Package Reflow Conditions

pkg. thickness ≥

≥≥

≥ 2.5mm

and all bgas

pkg. thickness < 2.5mm and

pkg. volume ≥

≥≥

≥ 350 mm³

pkg. thickness < 2.5mm and pkg.

volume < 350mm³

Convection 220 +5/-0 °C Convection 235 +5/-0 °C

VPR 215-219 °C VPR 235 +5/-0 °C

IR/Convection 220 +5/-0 °C IR/Convection 235 +5/-0 °C

Terminal Material Solder-Plated Copper (Solder Material : 90/10 or 63/37 SnPb)

Lead Solderability Meets EIA Specification RSI86-91, ANSI/J-STD-002 Category 3.

Reference JEDEC Standard J-STD-020A APRIL 1999

Reflow Condition (IR/Convection or VPR Reflow)

Rev. A.9 - May., 2003

APL5501/2/3

www.anpec.com.tw21

Reliability test program

Test item Method Description

SOLDERABILITY MIL-STD-883D-2003 245°C , 5 SEC

HOLT MIL-STD-883D-1005.7 1000 Hrs Bias @ 125 °C

PCT JESD-22-B, A102 168 Hrs, 100 % RH , 121°C

TST MIL-STD-883D-1011.9 -65°C ~ 150°C, 200 Cycles

ESD MIL-STD-883D-3015.7 VHBM > 2KV, VMM > 200V

Latch-U p JESD 78 10m s , Itr > 100mA

Carrier Tape

Po P

Rev. A.9 - May., 2003

APL5501/2/3

www.anpec.com.tw22

Application Carrier Width Cover Tape Width Devices Per Reel

SOP- 8 12 9.3 2500

SOT- 89 12 9.3 1000

SOT- 223 12 9.3 2500

TO- 252 16 13.3 2500

Anpec Electronics Corp.

Head Office :

5F, No. 2 Li-Hsin Road, SBIP,

Hsin-Chu, Taiwan, R.O.C.

Tel : 886-3-5642000

Fax : 886-3-5642050

Taipei Branch :

7F, No. 137, Lane 235, Pac Chiao Rd.,

Hsin Tien City, Taipei Hsien, Taiwan, R. O. C.

Tel : 886-2-89191368

Fax : 886-2-89191369

Customer Service

Reel Dimensions

Cover Tape Dimensions

lication A B C J T1 T2 W P E

330 ± 1 62 +1.5 12.75+ 0.15 2 ± 0.5 12.4 ± 0.2 2 ± 0.2 12± 0. 3 8± 0.1 1 .75±0.1

F D D1 Po P1 Ao Bo Ko t

SOP- 8

5.5± 1 1.55 +0.1 1.55+ 0.25 4.0 ± 0.1 2.0 ± 0.1 6.4 ± 0.1 5.2± 0. 1 2.1± 0.1 0.3±0.013

lication A B C J T1 T2 W P E

178 ±1 70 ± 2 13.5 ± 0.15 3 ± 0.15 14 ± 2 1.3 ± 0.3 12 + 0.3

12 - 0.1 8 ± 0.1 1.75± 0.1

F D D1 Po P1 Ao Bo Ko t

SOT-89

5.5 ± 0.05 1.5± 0.1 1.5± 0.1 4.0 ± 0.1 2.0 ± 0.1 4.8 ± 0.1 4.5± 0.1 1.80± 0.1 0.3±0.013

lication A B C J T1 T2 W P E

330±162

±1.5 12.75±

0.15 2 ± 0.6 12.4 +0.2 2± 0.2 12 ± 0.3 8 ± 0.1 1.75± 0.1

F D D1 Po P1 Ao Bo Ko t

SOT-223

5.5 ± 0.05 1.5+ 0.1 1.5+ 0.1 4.0 ± 0.1 2.0 ± 0.05 6.9 ± 0.1 7.5± 0.1 2.1± 0.1 0.3±0.05

lication A B C J T1 T2 W P E

330 ±3 100 ± 2 13 ± 0. 5 2 ± 0.5 16.4 + 0.3

-0.2 2.5± 0.5 16+ 0.3

- 0.1 8 ± 0.1 1.75± 0.1

F D D1 Po P1 Ao Bo Ko t

TO-252

7.5 ± 0.1 1.5 +0.1 1.5± 0.25 4.0 ± 0.1 2.0 ± 0.1 6.8 ± 0.1 10.4± 0.1 2.5± 0.1 0.3±0.05