Technical Data Sheet 1.9mm Round Subminiature "Gull Wing" Lead Phototransistor PT91-21B/TR7 Features Fast response time High photo sensitivity Small junction capacitance Compatible with infrared and vapor phase reflow solder process. Pb free The product itself will remain within RoHS compliant version. Descriptions PT91-21B/TR7 is a phototransistor in miniature SMD package which is molded in black plastic with spherical top view lens. The device is spectrally matched to infrared emitting diode. Applications Miniature switch Counters and sorter Position sensor Infrared applied system Device Selection Guide LED Part No. Chip Material Lens Color PT Silicon Black Everlight Electronics Co., Ltd. http://www.everlight.com Device No Prepared date DTT-091-003 07-18-2008 Rev 3 Page: 1 of 10 Prepared by Daniel Yang PT91-21B/TR7 Package Dimensions 2.50.1 0.4 0.1 0.550.1 2.00.2 1.90.2 4.00.2 1.10.1 Collector Emitter 1.40.1 0.30.1 1.30.1 2.70.2 1.40.1 0.83 +0.13 -0 0.150.05 0.650.1 R0.80.1 0.750.1 Notes: 1.All dimensions are in millimeters 2.Tolerances unless dimensions 0.1mm Absolute Maximum Ratings (Ta=25 ) Parameter Symbol Rating Units Collector-Emitter Voltage VCEO 30 Emitter-Collector-Voltage VECO 5 V V IC 20 mA Operating Temperature Topr -25 ~ +85 Storage Temperature Tstg -40 ~ +100 Soldering Temperature Tsol 260 Power Dissipation at(or below) 25Free Air Temperature Pc 75 mW Collector Current Notes: *1:Soldering time5 seconds. Everlight Electronics Co., Ltd. http://www.everlight.com Device No Prepared date DTT-091-003 07-18-2008 Rev 3 Page: 2 of 10 Prepared by Daniel Yang PT91-21B/TR7 Electro-Optical Characteristics (Ta=25 ) Parameter Symbol Condition Min Typ Max Unit 10%P --- 730 --- 1100 nm P --- --- 940 --- nm Collector-Emitter Breakdown Voltage BVCEO IC=100A Ee=0mW/cm2 30 --- --- V Emitter-Collector Breakdown Voltage BVECO 5 --- --- V Collector-Emitter Saturation Voltage VCE(sat) IC=2mA Ee=1m W/cm2 --- --- 0.4 V Collector Dark Current ICEO VCE=20V Ee=0mW/cm2 --- --- 100 nA On State Collector Current IC(ON) VCE=5V Ee=1mW /cm2 1.0 1.5 Angle of half sensitivity VCE=5V --- 35 --- Rise Time tr --- 15 --- Fall Time tf VCE=5V IC=1mA RL=1000 --- 15 --- Rang Of Spectral Bandwidth Wavelength Of Peak Sensitivity IE=100A Ee=0mW/cm2 Everlight Electronics Co., Ltd. http://www.everlight.com Device No Prepared date DTT-091-003 07-18-2008 mA deg S Rev 3 Page: 3 of 10 Prepared by Daniel Yang PT91-21B/TR7 Typical Electro-Optical Characteristics Curves Fig.1Collector Power Dissipation vs. Ambient Temperature 100 Fig.2 Spectral Sensitivity 1.0 Ta=25C 80 0.8 60 0.6 40 0.4 20 0.2 0 -25 25 0 50 75 85 100 Fig.3 Relative Collector Current vs. 0 700 800 900 1000 1100 1300 Fig.4 Collector Current vs. Ambient Temperature Irradiance 10 160 2 140 C 1 120 100 0.1 80 60 0.01 40 20 0 0 10 20 30 40 50 60 70 0.001 0.01 1 0.1 10 2 Everlight Electronics Co., Ltd. http://www.everlight.com Device No Prepared date DTT-091-003 07-18-2008 Rev 3 Page: 4 of 10 Prepared by Daniel Yang PT91-21B/TR7 Typical Electro-Optical Characteristics Curves Fig.5 Collector Dark Current vs. Fig.6 Collector Current vs. Ambient Temperature Collector-Emitter Voltage 10 4.0 3.5 10 3.0 2.5 10 2.0 1.5 10 1.0 10 0 50 25 75 100 0 0 1 2 3 4 Fig 7. Relative Radiant Sensitivity vs. Angular Displacement -20 -10 0 10 20 30 1.0 40 0.9 50 0.8 0.7 60 70 80 0.6 0.4 0.2 0 0.2 0.4 0.6 Everlight Electronics Co., Ltd. http://www.everlight.com Device No Prepared date DTT-091-003 07-18-2008 Rev 3 Page: 5 of 10 Prepared by Daniel Yang PT91-21B/TR7 Precautions For Use 1. Over-current-proof Customer must apply resistors for protection , otherwise slight voltage shift will cause big current change ( Burn out will happen ). 2. Storage 2.1 Do not open moisture proof bag before the products are ready to use. 2.2 Before opening the package, the LEDs should be kept at 30 or less and 90%RH or less. 2.3 The LEDs should be used within a year. 2.4 After opening the package, the LEDs should be kept at 30 or less and 70%RH or less. 2.5 The LEDs should be used within 168 hours (7 days) after opening the package. 2.6 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the storage time, baking treatment should be performed using the following conditions. Baking treatment : 605 for 24 hours. 3. Soldering Condition 3.1 Pb-free solder temperature profile 3.2 Reflow soldering should not be done more than two times. 3.3 When soldering, do not put stress on the LEDs during heating. 3.4 After soldering, do not warp the circuit board. Everlight Electronics Co., Ltd. http://www.everlight.com Device No Prepared date DTT-091-003 07-18-2008 Rev 3 Page: 6 of 10 Prepared by Daniel Yang PT91-21B/TR7 4.Soldering Iron Each terminal is to go to the tip of soldering iron temperature less than 280 for 3 seconds within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do soldering of each terminal. Be careful because the damage of the product is often started at the time of the hand solder. 5.Repairing Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether the characteristics of the LEDs will or will not be damaged by repairing. Everlight Electronics Co., Ltd. http://www.everlight.com Device No Prepared date DTT-091-003 07-18-2008 Rev 3 Page: 7 of 10 Prepared by Daniel Yang PT91-21B/TR7 Reliability Test Item And Condition The reliability of products shall be satisfied with items listed below. Confidence level90% LTPD10% NO. Item Test Conditions 1 REFLOW Soldering TEMP.2605 5secs 2 Temperature Cycle H : +100 3 Thermal Shock Test Hours/ Sample Failure Cycles Sizes Judgement Criteria Ac/Re 6Mins 0/1 15mins 50Cycles L : -40 5mins 15mins H :+100 5mins 50Cycles L :-10 10secs 5mins 22pcs 22pcs IC(ON)Lx0.8 0/1 LLower 22pcs Specification Limit 0/1 4 High Temperature Storage TEMP.+100 1000hrs 22pcs 0/1 5 Low Temperature TEMP.-40 1000hrs 22pcs 0/1 1000hrs 22pcs 0/1 1000hrs 22pcs 0/1 Storage 6 DC Operating Life VCE=5V 7 High Temperature/ 85 / 85% R.H High Humidity Everlight Electronics Co., Ltd. http://www.everlight.com Device No Prepared date DTT-091-003 07-18-2008 Rev 3 Page: 8 of 10 Prepared by Daniel Yang PT91-21B/TR7 Package Dimensions Taping Dimensions 1 2 1 Unit :mm Everlight Electronics Co., Ltd. http://www.everlight.com Device No Prepared date DTT-091-003 07-18-2008 Rev 3 Page: 9 of 10 Prepared by Daniel Yang PT91-21B/TR7 Packing Quantity Specification 1.1000Pcs/1Volume1Volume/1Bag 2.10Boxes/1Carton Label Form Specification CPN: Customer's Production Number P/N : Production Number QTY: Packing Quantity CAT: Ranks HUE: Peak Wavelength RoHS PT91-21B/TR7 REF: Reference LOT No: Lot Number MADE IN TAIWAN: Production Place Notes 1. Above specification may be changed without notice. EVERLIGHT will reserve authority on material change for above specification. 2. When using this product, please observe the absolute maximum ratings and the instructions for using outlined in these specification sheets. EVERLIGHT assumes no responsibility for any damage resulting from use of the product which does not comply with the absolute maximum ratings and the instructions included in these specification sheets. 3. These specification sheets include materials protected under copyright of EVERLIGHT corporation. Please don't reproduce or cause anyone to reproduce them without EVERLIGHT's consent. EVERLIGHT ELECTRONICS CO., LTD. Office: No 25, Lane 76, Sec 3, Chung Yang Rd, Tucheng, Taipei 236, Taiwan, R.O.C Tel: 886-2-2267-2000, 2267-9936 Fax: 886-2267-6244, 2267-6189, 2267-6306 http://www.everlight.com Everlight Electronics Co., Ltd. http://www.everlight.com Device No Prepared date DTT-091-003 07-18-2008 Rev 3 Page: 10 of 10 Prepared by Daniel Yang