© Semiconductor Components Industries, LLC, 2013
May, 2013 Rev. 12
1Publication Order Number:
MUR120/D
MUR120 Series
SWITCHMODE
Power Rectifiers
MUR105, MUR110, MUR115, MUR120,
MUR130, MUR140, MUR160
The MUR120 series of SWITCHMODE power rectifiers are
designed for use in switching power supplies, inverters and as free
wheeling diodes.
Features
Ultrafast 25, 50 and 75 Nanosecond Recovery Times
175°C Operating Junction Temperature
Low Forward Voltage
Low Leakage Current
High Temperature Glass Passivated Junction
Reverse Voltage to 600 V
Shipped in Plastic Bags; 1,000 per Bag
Available Tape and Reel; 5,000 per Reel, by adding a “RL’ Suffix to
the Part Number
These are PbFree Devices*
Mechanical Characteristics:
Case: Epoxy, Molded
Weight: 0.4 Gram (Approximately)
Finish: All External Surfaces Corrosion Resistant and Terminal
Leads are Readily Solderable
Lead Temperature for Soldering Purposes:
260°C Max. for 10 Seconds
Polarity: Cathode Indicated by Polarity Band
*For additional information on our PbFree strategy and soldering details, please
download the ON Semiconductor Soldering and Mounting Techniques
Reference Manual, SOLDERRM/D.
See detailed ordering and shipping information in the package
dimensions section on page 6 of this data sheet.
ORDERING INFORMATION
ULTRAFAST RECTIFIERS
1.0 AMPERE, 50 600 VOLTS
http://onsemi.com
MARKING DIAGRAM
A = Assembly Location
MUR1xx = Specific Device Code
Y = Year
WW = Work Week
G= PbFree Package
(Note: Microdot may be in either location)
A
MUR
1xx
YYWW G
G
AXIAL LEAD
CASE 59
STYLE 1
MUR120 Series
http://onsemi.com
2
MAXIMUM RATINGS
Rating Symbol
MUR
Unit
105 110 115 120 130 140 160
Peak Repetitive Reverse Voltage
Working Peak Reverse Voltage
DC Blocking Voltage
VRRM
VRWM
VR
50 100 150 200 300 400 600 V
Average Rectified Forward Current
(Square Wave Mounting Method #3 Per Note 2)
IF(AV) 1.0 @ TA = 130°C1.0 @ TA = 120°C A
Nonrepetitive Peak Surge Current
(Surge applied at rated load conditions, halfwave,
single phase, 60 Hz)
IFSM 35 A
Operating Junction Temperature and Storage Temperature TJ, Tstg *65 to +175 °C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
THERMAL CHARACTERISTICS
Characteristic Symbol Max Unit
Maximum Thermal Resistance, JunctiontoAmbient RqJA Note 2 °C/W
ELECTRICAL CHARACTERISTICS
Characteristic Symbol Value Unit
Maximum Instantaneous Forward Voltage (Note 1)
(iF = 1.0 Amp, TJ = 150°C)
(iF = 1.0 Amp, TJ = 25°C)
vF0.710
0.875
1.05
1.25
V
Maximum Instantaneous Reverse Current (Note 1)
(Rated DC Voltage, TJ = 150°C)
(Rated DC Voltage, TJ = 25°C)
iR50
2.0
150
5.0
mA
Maximum Reverse Recovery Time
(IF = 1.0 A, di/dt = 50 A/ms)
(IF = 0.5 A, iR = 1.0 A, IREC = 0.25 A)
trr 35
25
75
50
ns
Maximum Forward Recovery Time
(IF = 1.0 A, di/dt = 100 A/ms, IREC to 1.0 V)
tfr 25 50 ns
Typical Peak Reverse Recovery Current
(IF = 1.0 A, di/dt = 50 A/ms)
IRM 0.85 A
1. Pulse Test: Pulse Width = 300 ms, Duty Cycle 2.0%.
MUR120 Series
http://onsemi.com
3
MUR105, MUR110, MUR115, MUR120
Figure 1. Typical Forward Voltage
vF, INSTANTANEOUS VOLTAGE (VOLTS)
0.3 0.60.4 0.8
3.0
0.01
0.03
0.02
0.2
0.1
10
2.0
0.7
0.3
0.05
0.5
5.0
, INSTANTANEOUS FORWARD CURRENT (AMPS)
F
1.3
VR, REVERSE VOLTAGE (VOLTS)
06040 100 120
100
0.01
0.001
1.0
10
TJ = 175°C
IR
20 80 200
Figure 2. Typical Reverse Current*
IF(AV), AVERAGE FORWARD CURRENT (AMPS)
0
1.0
2.0
3.0
4.0
5.0
PF(AV)
0
0.5 1.0 1.5 2.0 2.5
TA, AMBIENT TEMPERATURE (°C)
050
0
2.0
1.0
3.0
5.0
4.0
I
250
Figure 3. Current Derating
(Mounting Method #3 Per Note 1)
Figure 4. Power Dissipation
0
10
30
50
5.0
10 20
VR, REVERSE VOLTAGE (VOLTS)
Figure 5. Typical Capacitance
0.5
0.07
1.0
7.0
1.0 1.2
100°CTJ = 175°C
25°C
160 180140
0.1
, REVERSE CURRENT ( A)
100°C
25°C
150100 200
* The curves shown are typical for the highest voltage device in the
voltage grouping. Typical reverse current for lower voltage selections
can be estimated from these same curves if VR is sufficiently below
rated VR.
C, CAPACITANCE (pF)
, AVERAGE POWER DISSIPATION (WATTS)
TJ = 25°C
i
, AVERAGE FORWARD CURRENT (AMPS)
F(AV)
30 40 50
7.0
20
TJ = 175°C
RATED VR
RqJA = 50°C/W
dc
SQUARE WAVE
m
(CAPACITIVELOAD)
IPK
IAV
+20
SQUARE WAVE
dc
5.0
10
0.7 0.9 1.1
MUR120 Series
http://onsemi.com
4
MUR130, MUR140, MUR160
Figure 6. Typical Forward Voltage
vF, INSTANTANEOUS VOLTAGE (VOLTS)
0.3 0.90.5 1.3
3.0
0.01
0.03
0.02
0.2
0.1
10
2.0
0.7
0.3
0.05
0.5
5.0
, INSTANTANEOUS FORWARD CURRENT (AMPS)
F
2.3
VR, REVERSE VOLTAGE (VOLTS)
0 200100 300 400
100
0.01
0.004
1.0
10
TJ = 175°C
IR
700
Figure 7. Typical Reverse Current*
IF(AV), AVERAGE FORWARD CURRENT (AMPS)
0
1.0
2.0
3.0
4.0
5.0
PF(AV)
0
0.5 1.0 1.5 2.0 2.5
TA, AMBIENT TEMPERATURE (°C)
050
0
2.0
1.0
3.0
5.0
4.0
I
250
Figure 8. Current Derating
(Mounting Method #3 Per Note 2)
Figure 9. Power Dissipation
0
5.0
10
20
2.0
10 20
VR, REVERSE VOLTAGE (VOLTS)
Figure 10. Typical Capacitance
0.7
0.07
1.0
7.0
1.7 2.1
100°C
TJ = 175°C
25°C
600500
0.1
, REVERSE CURRENT ( A)
100°C
25°C
150100 200
* The curves shown are typical for the highest voltage device in the
voltage grouping. Typical reverse current for lower voltage selections
can be estimated from these same curves if VR is sufficiently below
rated VR.
C, CAPACITANCE (pF)
, AVERAGE POWER DISSIPATION (WATTS)
TJ = 25°C
i
, AVERAGE FORWARD CURRENT (AMPS)
F(AV)
30 40 50
3.0
7.0
TJ = 175°C
RATED VR
RqJA = 50°C/W
dc
SQUARE WAVE
m
IPK
IAV
+20
SQUARE WAVE
dc
5.0
10
1.1 1.5 1.9
400
0.04
4.0
40
0.4
(CAPACITIVE LOAD)
MUR120 Series
http://onsemi.com
5
Lead Length, L (in.)
Mounting
Method 1/8 1/4 1/2 Units
1
2
3
52
67
RqJA
65 72
80 87
50
°C/W
°C/W
°C/W
TYPICAL VALUES FOR RqJA IN STILL AIR
Data shown for thermal resistance, junctiontoambient
(RqJA) for the mountings shown is to be used as typical
guideline values for preliminary engineering or in case the
tie point temperature cannot be measured.
NOTE 2. — AMBIENT MOUNTING DATA
MOUNTING METHOD 1
MOUNTING METHOD 2
MOUNTING METHOD 3
ÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉ
L L
ÉÉÉÉÉÉÉÉÉÉÉÉ
ÉÉÉÉÉÉÉÉÉÉÉÉ
L L
Vector Pin Mounting
ÉÉ
ÉÉ
ÉÉ
ÉÉ
ÉÉ
ÉÉ
ÉÉ
L = 3/8
Board Ground Plane
P.C. Board with
11/2 X 11/2 Copper Surface
MUR120 Series
http://onsemi.com
6
ORDERING INFORMATION
Device Marking Package Shipping
MUR105 MUR105 Axial Lead* 1000 Units / Bag
MUR105G MUR105 Axial Lead* 1000 Units / Bag
MUR105RL MUR105 Axial Lead* 5000 Units / Tape & Reel
MUR105RLG MUR105 Axial Lead* 5000 Units / Tape & Reel
MUR110 MUR110 Axial Lead* 1000 Units / Bag
MUR110G MUR110 Axial Lead* 1000 Units / Bag
MUR110RL MUR110 Axial Lead* 5000 Units / Tape & Reel
MUR110RLG MUR110 Axial Lead* 5000 Units / Tape & Reel
MUR115 MUR115 Axial Lead* 1000 Units / Bag
MUR115G MUR115 Axial Lead* 1000 Units / Bag
MUR115RL MUR115 Axial Lead* 5000 Units / Tape & Reel
MUR115RLG MUR115 Axial Lead* 5000 Units / Tape & Reel
MUR120 MUR120 Axial Lead* 1000 Units / Bag
MUR120G MUR120 Axial Lead* 1000 Units / Bag
MUR120RL MUR120 Axial Lead* 5000 Units / Tape & Reel
MUR120RLG MUR120 Axial Lead* 5000 Units / Tape & Reel
MUR130 MUR130 Axial Lead* 1000 Units / Bag
MUR130G MUR130 Axial Lead* 1000 Units / Bag
MUR130RL MUR130 Axial Lead* 5000 Units / Tape & Reel
MUR130RLG MUR130 Axial Lead* 5000 Units / Tape & Reel
MUR140 MUR140 Axial Lead* 1000 Units / Bag
MUR140G MUR140 Axial Lead* 1000 Units / Bag
MUR140RL MUR140 Axial Lead* 5000 Units / Tape & Reel
MUR140RLG MUR140 Axial Lead* 5000 Units / Tape & Reel
MUR160 MUR160 Axial Lead* 1000 Units / Bag
MUR160G MUR160 Axial Lead* 1000 Units / Bag
MUR160RL MUR160 Axial Lead* 5000 Units / Tape & Reel
MUR160RLG MUR160 Axial Lead* 5000 Units / Tape & Reel
For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
*This package is inherently PbFree.
MUR120 Series
http://onsemi.com
7
PACKAGE DIMENSIONS
B
D
K
K
F
F
A
DIM MIN MAX MIN MAX
MILLIMETERSINCHES
A4.10 5.200.161 0.205
B2.00 2.700.079 0.106
D0.71 0.860.028 0.034
F−−− 1.27−−− 0.050
K25.40 −−−1.000 −−−
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. ALL RULES AND NOTES ASSOCIATED WITH
JEDEC DO41 OUTLINE SHALL APPLY
4. POLARITY DENOTED BY CATHODE BAND.
5. LEAD DIAMETER NOT CONTROLLED WITHIN F
DIMENSION.
AXIAL LEAD
CASE 5910
ISSUE U
POLARITY INDICATOR
OPTIONAL AS NEEDED
(SEE STYLES)
STYLE 1:
PIN 1. CATHODE (POLARITY BAND)
2. ANODE
ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/PatentMarking.pdf. SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages.Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC
does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where
personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture
of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
N. American Technical Support: 8002829855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81358171050
MUR120/D
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 3036752175 or 8003443860 Toll Free USA/Canada
Fax: 3036752176 or 8003443867 Toll Free USA/Canada
Email: orderlit@onsemi.com
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative