SSD1303T3R1 - Solomon Systech

SOLOMON SYSTECH

SEMICONDUCTOR TECHNICAL DATA

This document contai ns information on a new product. Speci fications and information herei n are subject to

change without noti ce.

http://www.solomon-systech.com

SSD1303 Rev 1.7 P 1/56 May 2005 Copyright  2005 S olomon Systech Limited

Advance Info rmation

132 x 64 Dot Matrix

OLED/PLED Segment/Common Dr iver with Controll er

SSD1303

Solomon S ystech May 2005 P 2/56 Rev 1.7 SSD1303

TABLE OF CONTENTS

1 GENERAL INFORMATION ............................................................................................................................5

2 FEATURES .........................................................................................................................................................5

3 ORDERING INFORMATION..........................................................................................................................6

4 BLOCK DIAGRAM ...........................................................................................................................................7

5 DIE PAD FLOOR PLAN....................................................................................................................................8

6 PIN DESCRIPTION.........................................................................................................................................12

7 FUNCTIONAL BLOCK DESCRIPTIONS....................................................................................................15

7.1 OSCILLATOR CIRC UIT AND DISPLAY TIME GENERATOR ..................................................................................15

7.2 RESET CIRCUIT ................................................................................................................................................15

7.3 COMMAND DEC ODER AND COMMAND INTERFACE ..........................................................................................15

7.4 MPU PARALLEL 6800-SERIES INTERFACE .......................................................................................................16

7.5 MPU PARALLEL 8080-SERIES INTERFACE .......................................................................................................16

7.6 MPU SERIAL INTERFACE.................................................................................................................................17

7.7 GRAPHIC DISPLAY DATA RAM (GDDRAM)..................................................................................................17

7.8 CURRENT CON TRO L AND VOLTAGE CONTROL.................................................................................................17

7.9 SEGMENT DRIVERS / COMMON DRIVERS .........................................................................................................18

7.10 AREA COLOUR DECODER.................................................................................................................................18

7.11 DC-DC VOLTAGE CONVERTER .......................................................................................................................19

8 COMMAND TABLE........................................................................................................................................21

8.1 DATA READ / WRITE........................................................................................................................................24

9 COMMAND DESCRIPTIONS........................................................................................................................25

10 MAXIMUM RATINGS....................................................................................................................................32

11 DC CHARACTERISTICS ...............................................................................................................................33

12 AC CHARACTERISTICS ...............................................................................................................................34

13 APPLICATION EXAMPLE............................................................................................................ ................38

14 SSD1303T3R1 PACKAGE DETAILS.............................................................................................................39

SSD1303T3R1 PIN ASSIGNMENT................................................................................................................................39

15 SSD1303T6R1 PACKAGE DETAILS.............................................................................................................43

SSD1303T6R1 PIN ASSIGNMENT................................................................................................................................43

SSD1303T6R1 TAB PACKAGE DIMENSIONS ..............................................................................................................45

16 SSD1303T8R1 PACKAGE DETAILS.............................................................................................................47

SSD1303T8R1 PIN ASSIGNMENT................................................................................................................................47

SSD1303T8R1 TAB PACKAGE DIMENSIONS ..............................................................................................................49

17 SSD1303T9R1 PACKAGE DETAILS.............................................................................................................51

SSD1303T9R1 PIN ASSIGNMENT................................................................................................................................51

SSD1303T9R1 TAB PACKAGE DIMENSIONS ..............................................................................................................53

SSD1303 Rev 1.7 P 3/56 May 2005 Solomon S ystech

18 SSD1303Z PACKAGE DETAILS ...................................................................................................................55

Solomon S ystech May 2005 P 4/56 Rev 1.7 SSD1303

TABLE OF FIGURES

Figure 1 - Block Diagram..................................................................................................................................7

Figure 2 - SSD1303Z Pin Assignment .............................................................................................................8

Figure 3 - SSD1303Z Alignment mark dimensions........................................................................................11

Figure 4 - Oscillator Circuit.............................................................................................................................15

Figure 5 - Display data read back procedure - insertion of dummy read.......................................................16

Figure 6 – Display data write procedure in SPI mode....................................................................................17

Figure 7 - DC-DC voltage converter circuit....................................................................................................19

Figure 8 - Horizontal scroll direction...............................................................................................................25

Figure 9 - Segment current vs Contrast setting .............................................................................................26

Figure 10 - 6800-series MPU parallel interface characteristics .....................................................................35

Figure 11 - 8080-series MPU parallel interface characteristics .....................................................................36

Figure 12 - Serial interface charac teristic s.....................................................................................................37

Figure 13 - Application Example (Block Diagram of SSD1303T3).................................................................38

Figure 14 - SSD1303T 3R1 pin as signment (Copper view, Normal TAB design) ..........................................39

Figure 15 - SSD1303T 6R1 pin ass ignment (Copper view)............................................................................43

Figure 16 - SSD1303T 9R1 pin ass ignment (Copper view)............................................................................51

LIST OF TABLES

Table 1 - Ordering Information.........................................................................................................................6

Table 2 - SSD1303Z Die Pad Coordinates......................................................................................................9

Table 3 - Passive component selection: ........................................................................................................20

Table 4 - Command table...............................................................................................................................21

Table 5 - Read command table......................................................................................................................23

Table 6 - Address increment table (Automatic)..............................................................................................24

Table 7 - Maximum Ratings ...........................................................................................................................32

Table 8 - DC Characteristics..........................................................................................................................33

Table 9 - AC Characteristics ..........................................................................................................................34

Table 10 - 6800-Series MPU Parallel Interface Timing Characteristics.........................................................35

Table 11 - 8080-Series MPU Parallel Interface Timing Characteristics.........................................................36

Table 12 - Serial Interface Timing Characteristics.........................................................................................37

Table 13 - SSD1303T 3R1 pin ass ignm ent.....................................................................................................40

Table 14 - SSD1303T 6R1 pin ass ignm ent.....................................................................................................44

Table 15 - SSD1303T 8R1 pin ass ignm ent.....................................................................................................48

Table 16 - SSD1303T 9R1 pin ass ignm ent.....................................................................................................52

SSD1303 Rev 1.7 P 5/56 May 2005 Solomon S ystech

1 GENERAL INFORMATION

The SSD1303 is a single-chip CMOS OLED/PLED driver with controller for organic/polymer light

emitting diode dot-matrix graphic display system. It consists of 132 segments, 64 commons that can

support a maximum display resolution of 132x64. Besides, there are 4-colour selections to support

monochrome or area colour OLED/PLED. This IC is designed for Common Cathode type OLED panel.

The SSD1303 em beds with contras t control, display RAM and oscillator, which reduces the number

of external com ponents and power cons um ption. It is s uitable for m any compact por table applications, s uch

as mobile phone sub-display, calculator and MP3 player, etc.

2 FEATURES

- Support maximum 132 x 64 dot matrix panel

- Area colour support with 4 Colour Selection and 64 steps per colour

- Logic voltage supply: VDD = 2.4V - 3.5V

- High voltage supply: VCC = 7.0V - 16.0V

- Maximum segment output current: 320uA

- Maximum common sink current: 45mA

- Embedded 132 x 64 bit SRAM display buffer

- 256-step Contrast Control on monochrome passive OLED panel

- On-Chip Oscillator

- Programmable Frame Frequency and Multiplexing Ratio

- 8-bit 6800-series Parallel Interface, 8-bit 8080-series Parallel Interface, Serial Peripheral Interface

- Row Re-mapping and Column Re-mapping

- Vertical Scrolling

- Automatic horizontal scrolling function

- Low power consumption

- Wide range of operating temperatures: -40 to 90 °C

Solomon S ystech May 2005 P 6/56 Rev 1.7 SSD1303

3 ORDERING INFORMATION

Table 1 - Orderi ng Information

Ordering Part Number SEG COM Package Form Reference Remark

SSD1303Z 132 64 Gold Bump Die

Page 8

Die size: 9.22mm x 1.55mm

Pad pitch: COM 51.8µm SEG 52.2µm

SSD1303T3R1 96 64 TAB Page 39

• 35mm film

• 4 sprocket hole

• Folding TAB

• 80 / 68 / SPI interface

• Output lead pitch 0.12974mm

SSD1303T6R1 132 64 TAB Page 43

• 35mm film

• 4 sprocket hole

• Folding TAB

• 80 / 68 / SPI interface

• Output lead pitch 0.11976

SSD1303T8R1 96 64 TAB Page 47

• 35mm film

• 4 sprocket hole

• Folding TAB

• 80 / 68 / SPI interface

• Output lead pitch 0.12974mm

SSD1303T9R1 96 64 TAB Page 51

• 35mm film

• 4 sprocket hole

• Folding TAB

• 80 / 68 / SPI interface

• Output lead pitch 0.12974mm

SSD1303 Rev 1.7 P 7/56 May 2005 Solomon S ystech

Common Drivers (even) Segment Drivers Common Drivers(odd)

Area Colour Decorder

Display

Timing

Generator

Oscillator

GDDRAM

MCU

Interface

Command

Decoder

4 BLOCK DIAGRAM

Figure 1 - Block Diagram

RES

D/C

E (RD#)

R/W (WR#)

BS2

BS1

BS0

Voltage Cont rol

Current Control

VDD

VSS

COM63

COM61

COM3

COM1

SEG131

SEG130

SEG1

SEG0

COM0

COM2

COM60

COM62

CLS

VDDB

VSSB

RESE

VBREF

VCC

VCOMH

VREF

IREF

VCL

VSL

Solomon S ystech May 2005 P 8/56 Rev 1.7 SSD1303

5 DIE PAD FLOOR PLAN

Figure 2 - SSD1303Z Pin Assignment

DU MMY (x2)

COM32

COM34

COM60

COM62

VSS (x3)

VCL (x3)

VSS (x2)

VSL (x3)

VDD

VCC (x2)

VREF

VCOMH (x2)

IREF

ICAS

VDD

CLS

M/S

VSS

VDD

E/RD

R/W

VSS

D/C

RES#

CS#

VSS

DOF#

VSS

BS2

VDD

BS1

VSS

BS0

VDD

GPIO1

GPIO0

VCC

VSS

BGGND

SENSE

VBREF

RESE

VDD (x2)

VDDB (x2)

GDR (x2)

VSSB (x2)

VSS

TR0

TR1

TR2

TR3

TR4

TR5

TR6

TR7

TR8

VCOMH (x2)

VCC (x2)

VDD

VSL (x3)

VSSB (x2)

VSS (x2)

VCL (x3)

VSS (x3)

COM63

COM61

COM35

COM33

DU MMY (x2)

DUMMY

COM30

COM28

COM26

COM24

COM6

COM4

COM2

COM0

SEG0

SEG1

SEG2

SEG3

SEG4

SEG5

SEG6

SEG7

SEG8

SEG9

SEG10

SEG11

SEG12

SEG13

SEG117

SEG118

SEG119

SEG120

SEG121

SEG122

SEG123

SEG124

SEG125

SEG126

SEG127

SEG128

SEG129

SEG130

SEG131

COM1

COM3

COM5

COM7

COM25

COM27

COM29

COM31

DUMMY

PAD 1

Die size

D ie height

Bump height

Bum p size

Pad 1-18, 113-298

Pad 19-112

T shape (-3132.9, 79.5) 75um x 75um

+ shape (3148.9, 79.5) 75um x 75um

C ircle (3433.9, -274.6) R 37.5um, inner 18um

C ircle (-3433.9, -274.6) R 37.5um, inner 18um

34um x 84um

54um x 84um

Alignment mark

9.22mm x 1.55mm

475 +/- 25um

N ominal 18um

Pad 1,2,3,? >130

Gold Bumps face up

SSD1303 X

SSD1303 Rev 1.7 P 9/56 May 2005 Solomon S ystech

Table 2 - SSD1303Z Die Pad Coordinates

Pad no. Pad Na m e X-pos Y-pos Pad n o. Pad Na m e X-pos Y-pos Pad no. P ad Na me X-pos Y-pos

1 NC -4535.4 -679.6 61 VCC -342.9 -679.6 121 COM46 4068.4 -679.6

2 NC -4483.2 -679.6 62 GPIO0 -267.2 -679.6 122 COM44 4120.2 -679.6

3 COM33 -4431.0 -679.6 63 GPIO1 -190.5 -679.6 123 COM42 4172.0 -679.6

4 COM35 -4379.2 -679.6 64 VDD -114.3 -679.6 124 COM40 4223.8 -679.6

5 COM37 -4327.4 -679.6 65 BS0 -38.1 -679.6 125 COM38 4275.6 -679.6

6 COM39 -4275.6 -679.6 66 VSS 38.1 -679.6 126 COM36 4327.4 -679.6

7 COM41 -4223.8 -679.6 67 BS1 114.3 -679.6 127 COM34 4379.2 -679.6

8 COM43 -4172.0 -679.6 68 VDD 190.5 -679.6 128 COM32 4431.0 -679.6

9 COM45 -4120.2 -679.6 69 BS2 266.7 -679.6 129 NC 4483.2 -679.6

10 COM47 -4068.4 -679.6 70 VSS 342.9 -679.6 130 NC 4535.4 -679.6

11 COM49 -4016.6 -679.6 71 M 419.1 -679.6 131 NC 4535.4 679.6

12 COM51 -3964.8 -679.6 72 CL 495.3 -679.6 132 NC 4483.2 679.6

13 COM53 -3913.0 -679.6 73 DOF# 571.5 -679.6 133 COM30 4431.0 679.6

14 COM55 -3861.2 -679.6 74 VSS 647.7 -679.6 134 COM28 4379.2 679.6

15 COM57 -3809.4 -679.6 75 CS# 723.9 -679.6 135 COM26 4327.4 679.6

16 COM59 -3757.6 -679.6 76 RES# 800.1 -679.6 136 COM24 4275.6 679.6

17 COM61 -3705.8 -679.6 77 D/C 876.3 -679.6 137 COM22 4223.8 679.6

18 COM63 -3654.0 -679.6 78 VSS 952.5 -679.6 138 COM20 4172.0 679.6

19 VSS -3543.3 -679.6 79 R/W 1028.7 -679.6 139 COM18 4120.2 679.6

20 VSS -3467.1 -679.6 80 E/RD 1104.9 -679.6 140 COM16 4068.4 679.6

21 VSS -3390.9 -679.6 81 VDD 1181.1 -679.6 141 COM14 4016.6 679.6

22 VCL -3314.7 -679.6 82 D0 1257.3 -679.6 142 COM12 3964.8 679.6

23 VCL -3238.5 -679.6 83 D1 1333.5 -679.6 143 COM10 3913.0 679.6

24 VCL -3162.3 -679.6 84 D2 1409.7 -679.6 144 COM8 3861.2 679.6

25 VSS -3086.1 -679.6 85 D3 1485.9 -679.6 145 COM6 3809.4 679.6

26 VSS -3009.9 -679.6 86 D4 1562.1 -679.6 146 COM4 3757.6 679.6

27 VSSB -2933.7 -679.6 87 D5 1638.3 -679.6 147 COM2 3705.8 679.6

28 VSSB -2857.5 -679.6 88 D6 1714.5 -679.6 148 COM0 3654.0 679.6

29 VSL -2781.3 -679.6 89 D7 1790.7 -679.6 149 SEG0 3445.2 679.6

30 VSL -2705.1 -679.6 90 VSS 1866.9 -679.6 150 SEG1 3393.0 679.6

31 VSL -2628.9 -679.6 91 M/S 1943.1 -679.6 151 SEG2 3340.8 679.6

32 VDD -2552.7 -679.6 92 CLS 2019.3 -679.6 152 SEG3 3288.6 679.6

33 VCC -2476.5 -679.6 93 VDD 2095.5 -679.6 153 SEG4 3236.4 679.6

34 VCC -2400.3 -679.6 94 ICAS 2171.7 -679.6 154 SEG5 3184.2 679.6

35 VCOMH -2324.1 -679.6 95 IREF 2247.9 -679.6 155 SEG6 3132.0 679.6

36 VCOMH -2247.9 -679.6 96 VCOMH 2324.1 -679.6 156 SEG7 3079.8 679.6

37 TR8 -2171.7 -679.6 97 VCOMH 2400.3 -679.6 157 SEG8 3027.6 679.6

38 TR7 -2095.5 -679.6 98 VREF 2476.5 -679.6 158 SEG9 2975.4 679.6

39 TR6 -2019.3 -679.6 99 VCC 2552.7 -679.6 159 SEG10 2923.2 679.6

40 TR5 -1943.1 -679.6 100 VCC 2628.9 -679.6 160 SEG11 2871.0 679.6

41 TR4 -1866.9 -679.6 101 VDD 2705.1 -679.6 161 SEG12 2818.8 679.6

42 TR3 -1790.7 -679.6 102 VSL 2781.3 -679.6 162 SEG13 2766.6 679.6

43 TR2 -1714.5 -679.6 103 VSL 2857.5 -679.6 163 SEG14 2714.4 679.6

44 TR1 -1638.3 -679.6 104 VSL 2933.7 -679.6 164 SEG15 2662.2 679.6

45 TR0 -1562.1 -679.6 105 VSS 3009.9 -679.6 165 SEG16 2610.0 679.6

46 VSS -1485.9 -679.6 106 VSS 3086.1 -679.6 166 SEG17 2557.8 679.6

47 VSSB -1409.7 -679.6 107 VCL 3162.3 -679.6 167 SEG18 2505.6 679.6

48 VSSB -1333.5 -679.6 108 VCL 3238.5 -679.6 168 SEG19 2453.4 679.6

49 GDR -1257.3 -679.6 109 VCL 3314.7 -679.6 169 SEG20 2401.2 679.6

50 GDR -1181.1 -679.6 110 VSS 3390.9 -679.6 170 SEG21 2349.0 679.6

51 VDDB -1104.9 -679.6 111 VSS 3467.1 -679.6 171 SEG22 2296.8 679.6

52 VDDB -1028.7 -679.6 112 VSS 3543.3 -679.6 172 SEG23 2244.6 679.6

53 VDD -952.5 -679.6 113 COM62 3654.0 -679.6 173 SEG24 2192.4 679.6

54 VDD -876.3 -679.6 114 COM60 3705.8 -679.6 174 SEG25 2140.2 679.6

55 FB -800.1 -679.6 115 COM58 3757.6 -679.6 175 SEG26 2088.0 679.6

56 RESE -723.9 -679.6 116 COM56 3809.4 -679.6 176 SEG27 2035.8 679.6

57 VBREF -647.7 -679.6 117 COM54 3861.2 -679.6 177 SEG28 1983.6 679.6

58 SENSE -571.5 -679.6 118 COM52 3913.0 -679.6 178 SEG29 1931.4 679.6

59 BGGND -495.3 -679.6 119 COM50 3964.8 -679.6 179 SEG30 1879.2 679.6

60 VSS -419.1 -679.6 120 COM48 4016.6 -679.6 180 SEG31 1827.0 679.6

Solomon S ystech May 2005 P 10/56 Rev 1.7 SSD1303

Pad no. Pad Name X-pos Y-pos Pa d no. P a d Nam e X -pos Y-pos

181 SEG32 1774.8 679.6 241 SEG92 -1409.4 679.6

182 SEG33 1722.6 679.6 242 SEG93 -1461.6 679.6

183 SEG34 1670.4 679.6 243 SEG94 -1513.8 679.6

184 SEG35 1618.2 679.6 244 SEG95 -1566.0 679.6

185 SEG36 1566.0 679.6 245 SEG96 -1618.2 679.6

186 SEG37 1513.8 679.6 246 SEG97 -1670.4 679.6

187 SEG38 1461.6 679.6 247 SEG98 -1722.6 679.6

188 SEG39 1409.4 679.6 248 SEG99 -1774.8 679.6

189 SEG40 1357.2 679.6 249 SEG100 -1827.0 679.6

190 SEG41 1305.0 679.6 250 SEG101 -1879.2 679.6

191 SEG42 1252.8 679.6 251 SEG102 -1931.4 679.6

192 SEG43 1200.6 679.6 252 SEG103 -1983.6 679.6

193 SEG44 1148.4 679.6 253 SEG104 -2035.8 679.6

194 SEG45 1096.2 679.6 254 SEG105 -2088.0 679.6

195 SEG46 1044.0 679.6 255 SEG106 -2140.2 679.6

196 SEG47 991.8 679.6 256 SEG107 -2192.4 679.6

197 SEG48 939.6 679.6 257 SEG108 -2244.6 679.6

198 SEG49 887.4 679.6 258 SEG109 -2296.8 679.6

199 SEG50 835.2 679.6 259 SEG110 -2349.0 679.6

200 SEG51 783.0 679.6 260 SEG111 -2401.2 679.6

201 SEG52 730.8 679.6 261 SEG112 -2453.4 679.6

202 SEG53 678.6 679.6 262 SEG113 -2505.6 679.6

203 SEG54 626.4 679.6 263 SEG114 -2557.8 679.6

204 SEG55 574.2 679.6 264 SEG115 -2610.0 679.6

205 SEG56 522.0 679.6 265 SEG116 -2662.2 679.6

206 SEG57 469.8 679.6 266 SEG117 -2714.4 679.6

207 SEG58 417.6 679.6 267 SEG118 -2766.6 679.6

208 SEG59 365.4 679.6 268 SEG119 -2818.8 679.6

209 SEG60 313.2 679.6 269 SEG120 -2871.0 679.6

210 SEG61 261.0 679.6 270 SEG121 -2923.2 679.6

211 SEG62 208.8 679.6 271 SEG122 -2975.4 679.6

212 SEG63 156.6 679.6 272 SEG123 -3027.6 679.6

213 SEG64 104.4 679.6 273 SEG124 -3079.8 679.6

214 SEG65 52.2 679.6 274 SEG125 -3132.0 679.6

215 SEG66 0.0 679.6 275 SEG126 -3184.2 679.6

216 SEG67 -52.2 679.6 276 SEG127 -3236.4 679.6

217 SEG68 -104.4 679.6 277 SEG128 -3288.6 679.6

218 SEG69 -156.6 679.6 278 SEG129 -3340.8 679.6

219 SEG70 -208.8 679.6 279 SEG130 -3393.0 679.6

220 SEG71 -261.0 679.6 280 SEG131 -3445.2 679.6

221 SEG72 -365.4 679.6 281 COM1 -3654.0 679.6

222 SEG73 -417.6 679.6 282 COM3 -3705.8 679.6

223 SEG74 -469.8 679.6 283 COM5 -3757.6 679.6

224 SEG75 -522.0 679.6 284 COM7 -3809.4 679.6

225 SEG76 -574.2 679.6 285 COM9 -3861.2 679.6

226 SEG77 -626.4 679.6 286 COM11 -3913.0 679.6

227 SEG78 -678.6 679.6 287 COM13 -3964.8 679.6

228 SEG79 -730.8 679.6 288 COM15 -4016.6 679.6

229 SEG80 -783.0 679.6 289 COM17 -4068.4 679.6

230 SEG81 -835.2 679.6 290 COM19 -4120.2 679.6

231 SEG82 -887.4 679.6 291 COM21 -4172.0 679.6

232 SEG83 -939.6 679.6 292 COM23 -4223.8 679.6

233 SEG84 -991.8 679.6 293 COM25 -4275.6 679.6

234 SEG85 -1044.0 679.6 294 COM27 -4327.4 679.6

235 SEG86 -1096.2 679.6 295 COM29 -4379.2 679.6

236 SEG87 -1148.4 679.6 296 COM31 -4431.0 679.6

237 SEG88 -1200.6 679.6 297 NC -4483.2 679.6

238 SEG89 -1252.8 679.6 298 NC -4535.4 679.6

239 SEG90 -1305.0 679.6

240 SEG91 -1357.2 679.6

SSD1303 Rev 1.7 P 11/56 May 2005 S o l o m on S ystech

Figure 3 - SSD1303Z Alignment mark dimensions

T shape

+ shape

Circle

Unit in um

Solomon S ystech May 2005 P 12/56 Rev 1.7 SSD1303

6 P I N DE SCRIPTION

This pin is the system clock input. When internal clock is enabled, this pin should be left open. The internal

clock is output from this pin. W hen internal oscillator is disabled, this pin receives display clock signal from

external clock source.

CLS

This is the internal clock enable pin. When it is pulled HIGH, internal clock is enabled. When it is pulled

LOW, the internal clock is disabled, an external clock source must be connected to the CL pin for normal

operation.

BS0, BS1, BS2

These are MCU interface input selection pins. See the following table for selecting different interfaces:

6800-parallel

interface 8080-parallel

interface Serial

interface

BS0 0 0 0

BS1 0 1 0

BS2 1 1 0

CS#

This pin is the chip select input. The chip is enabled for MCU communication only when CS# had been

pulled low.

RES#

This is a reset signal input pin. When it is pulled LOW, initialization of the chip is executed.

D/C

This is the Data/Comm and contr ol pin. W hen it is pulled HIG H, the input at D7-D0 is treated as display data.

W hen it is pulled LO W , the input at D7-D0 is transf erred to the com m and registers . For detail relations hip to

MCU interface signals, please refer to the Timing Characteristics Diagrams.

R/W (WR#)

This is a MCU interf ace input pin. When 6800- series Parallel Inter face m ode is s elected, this pin is us ed as

Read/Write (R/W) selection input. Pull this pin to HIGH for read mode and pull it to LOW for write mode.

W hen 8080-series Parallel Interface m ode is selected, this pin is used as W rite (W R#) selection input. Pull

this pin to LO W f or write mode. Data write oper ation is initiated when this pin is pulled LOW and the CS# is

pulled LOW.

E (RD#)

This is a MCU interface input pin. When 6800-series Parallel Interface is selected, this pin is used as

Enable (E) signal. Read/W rite operation is initiated when this pin is pulled HIGH and the CS# pin is pulled

LOW. When 8080-series Parallel Interface is selected, this pin is used to receive the Read Data (RD#)

signal. Data read operation is initiated when this pin is pulled LOW and CS# pin is pulled LOW.

D7-D0

These are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial

interfac e m ode is selec ted, D1 will be the serial data input, SDIN, D0 will be the ser ial cloc k input, SCLK, and

D2 should be left opened.

SSD1303 Rev 1.7 P 13/56 May 2005 S o l o m on S ystech

VDD

This is a voltage supply pin. It must be connected to external source.

VSS

This is a ground pin. It also acts as a reference for the logic pins and the OLED driving voltages. It must be

connected to external ground.

BGGND

This is a ground pin for analog circuits. It must be connected to external ground

VCC

This is the most positive voltage supply pin of the chip. It should be supplied externally.

VREF

This is a voltage reference pin for pre-charge voltage in driving OLED device. Voltage should be set to

match with the OLED driving voltage in current drive phase. It can either be supplied externally or by

connecting to VCC.

IREF

This is a segment current reference pin. A resistor should be connected between this pin and VSS. Set the

current at 10uA.

VCOMH

This is an input pin for the voltage output high level for COM signals. A capacitor should be connected

between this pin and VSS.

VDDB This is a power supply pin for the internal buffer of the DC-DC voltage converter. It must be

connected to VDD when the converter is used.

VSSB

This is a ground pin for the internal buffer of the DC-DC voltage converter. It must be connected to VSS

when the converter is used.

GDR

This is an output pin drives the gate of the external NMOS of the booster circuit.

RESE

This is a source current pin of the external NMOS of the booster circuit.

VBREF

This is an internal voltage reference pin for booster circuit. A stabilization capacitor, typ. 1uF, should be

connected to Vss.

This is a feedback resistor input pin for the booster circuit. It is used to adjust the booster output voltage

level, Vcc.

COM0-COM63

These are pins provided the Common switch signals to the OLED panel. They are in high impedance state

when display is OFF.

Solomon S ystech May 2005 P 14/56 Rev 1.7 SSD1303

SEG0-SEG131

These are pins provided the Segment switch signals to the OLED panal. They are in high impedance stage

when display is OFF.

TR0-TR8, GPIO0, GPIO1, ICAS, M and DOF#

These are reserved pins. No connection necessary and should be left open individually.

VSL

This is a segment voltage reference pin. This pin should be connected to VSS externally.

VCL

This is a common voltage reference pin. This pin should be connected to VSS externally.

M/S

This pin must be connected to VDD to enable the chip.

Dummy pad. Do not group or short NC pins together.

SSD1303 Rev 1.7 P 15/56 May 2005 S o l o m on S ystech

7 FUNCTIONAL BLOCK DESCRIPTIONS

7.1 Oscillator Circuit and Display Time Generator

Figure 4 - Oscillator Circuit

This module is an On-Chip low power RC oscillator circuitry (Figure 4). The oscillator generates the clock

for the Display Timing Generator.

7.2 Reset Circuit

When RES# pin is pulled LOW, the chip is initialized with the following status:

1. Display is OFF

2. 132 x 64 Display Mode

3. Normal segment and display data column address and row address mapping (SEG0 is mapped to

column address 00H and COM0 is mapped to row address 00H)

4. Shift register data clear in serial interface

5. Display start line is set at display RAM address 0

6. Column address counter is set at 0

7. Normal scan direction of the COM outputs

8. Contrast control register is set at 80H

9. DC/DC enable

7.3 Command Decoder and Command Interface

This module determines whether the input data is interpreted as data or command. When the D/C# pin is

pulled HIGH, the inputs at D7-D0 are interpreted as data and be written to Graphic Display Data RAM

(GDDRAM). W hen it is pulled LOW , the inputs at D7-D0 are interpreted as comm and, they will be decoded

and be written to the corresponding command registers.

Divider

Internal

Oscillator

CL CLK DCLK

Internal

Displ ay

Clock

Solomon S ystech May 2005 P 16/56 Rev 1.7 SSD1303

7.4 MPU Parallel 6800- series Interface

The parallel interface consists of 8 bi-directional data pins (D7-D0), R/W (W R#), E (RD#), D/C, CS#. W hen

the R/W (W R#) pin is pulled HIGH, Read operation from the Graphic Display Data RAM (GDDRAM) or the

status register occurs. When the R/W (WR#) pin is pulled LOW, Write operation to Display Data RAM or

Internal Command Registers occurs, depending on the status of D/C input. The E (RD#) input serves as

data latch signal (clock) when HIGH provided that CS# is LOW . Refer to Parallel Interface Tim ing Diagram

of 6800-series microprocessors.

In order to match the operating frequency of display RAM with that of the microprocessor, some pipeline

processing is internally performed, which requires the insertion of a dummy read before the first actual

display data read. This is shown in Figure 5 below.

Figure 5 - Display data read back procedure - insertion of dummy read

7.5 MPU Parallel 8080- series Interface

The parallel interface consists of 8 bi-directional data pins (D7-D0), R/W (W R#), E (RD#), D/C, CS#. The E

(RD#) input ser ves as data r ead latc h signal ( cloc k) when it is LOW provided that CS# is LOW. Display data

or status register read is controlled by D/C signal.

R/W (W R#) input serves as data write latch signal (clock) when it is HIGH and provided that CS# is LOW .

Display data or command register write is controlled by D/C. Refer to Parallel Interface Timing Diagram of

8080-series micr oprocessor . Similar to 6800-series interf ace, a dum my read is also r equired before the first

actual display data read.

n+2

n+1

Write column address Dummy read Data read1

R/W#

(W/R#)

Data bus N n

(

RD#

)

Data read2 Data read3

SSD1303 Rev 1.7 P 17/56 May 2005 S o l o m on S ystech

7.6 MPU Serial Int erf ace

The serial interface consists of serial clock SCLK, serial data SDIN, D/C#, CS#. In SPI mode, D0 acts as

SCLK, D1 ac ts as SDIN. For the unused data pins , D2 s hould be left open. D3 to D7, E and R/W pins can

be connected to external ground.

SDIN is shif ted into an 8-bit shift r egister on every rising edge of SCLK in the order of D7, D6, ... D0. D/C# is

sampled on every eighth clock and the data byte in the shift register is written to the Display Data RAM or

command register in the same clock.

During data writing, an additional NOP command should be inserted before the CS# goes high (Refer to

Figure 6.

Figure 6 – Display data write procedure in SPI mode

D7 D6 D5 D4 D3 D2 D1 D0

SCLK(D0)

SDIN(D1)

DB1 DB2 DBn NOP COMMAND

CS#

D/C

SDIN/

SCLK

7.7 Graphi c Display Data RAM (GDDRAM)

The GDDRAM is a bit mapped static RAM holding the bit pattern to be displayed. The size of the RAM is

132 x 64 bits. For mechanical flexibility, re-mapping on both Segment and Common outputs can be

selected by software.

For vertical scrolling of the display, an internal register storing display start line can be set to control the

portion of the RAM data to be mapped to the display.

7.8 Current Control and Vol t age Cont rol

This block is used to derive the incoming power sources into different levels of internal use voltage and

current. VCC and VDD ar e external power supplies. VREF is reference voltage, which is us ed to derive the

driving voltage for segments and commons. IREF is a reference current source for segment current drivers.

Solomon S ystech May 2005 P 18/56 Rev 1.7 SSD1303

7.9 Segment Drivers / Common Drivers

Segment driver s deliver 132 curr ent s ources to drive OLED panel. T he driving c urrent c an be adjusted f rom

0 to 300uA with 256 steps. Common drivers generate voltage scanning pulses.

7.10 Area Colour Decoder

Page 0 and Page 1 of the dis play are divided into 32 banks. Bank 16 and Bank32 comprise of a dis play area

of 12 x 8 pixels . Other bank s (0~15 & 17~31) have m atr ices of 8 x 8 pix els. Each bank c an be program m ed

to any one of the four colours (colour A, B, C, D). Detailed operation can be referred to the Command

Table.

Page 0, bank 1 Page 0, bank 16

Page 1, bank 17 Page 1, bank 32

Bank 0 (background)

Page 2 – Page 7

SSD1303 Rev 1.7 P 19/56 May 2005 S o l o m on S ystech

7.11 DC-DC Voltage Convert er

It is a switching voltage generator circuit, designed for handheld applications. In SSD1303, internal DC-DC

voltage converter accom panying with an external application circuit (shown in below figure) can generate a

high voltage supply VCC from a low voltage supply input VDD. VCC is the voltage supply to the OLED driver

block. Below application circuit is an example for the input voltage of 3V VDD to generate VCC of 12V

@0mA ~ 20mA application.

Figure 7 - DC-DC voltage converter circuit

VDDB

VBREF

VSSB

GDR

RESE

VDD

AGND

DGND

AGND

VCC

L1 D1

C3C2

C6 +

Remark:

1. VSSB is tied to VSS on SSD1303T3 package.

2. L1, D1, Q1, C5 should be grouped closed together on PCB layout.

3. R1, R2, C1, C4 should be grouped closed together on PCB layout.

4. The VCC output voltage level can be adjusted by R1and R2, the reference formula is:

VCC = 1.2 x (R1+R2) / R2

The value of (R1+R2) should be between 500k to 1M Ohm.

Solomon S ystech May 2005 P 20/56 Rev 1.7 SSD1303

Table 3 - Passive component selection:

Components Typical Value Remark

L1 Inductor, 10µH 1A

D1 Schottky diode 1A, 25V e.g. 1N5822, BAT54 [Philips

Semiconductors]

Q1 MOSFET N-FET with low RDS(on) and low Vth voltage.

e.g. MGSF1N02LT1 [ON SEMI]

R1, R2 Resistor 1%,1/10W

R3 Resistor, 1.2Ω 1%, 1/2W

C1 Capacitor, 1µF 16V

C2 Capacitor, 6.8µF Low ESR, 25V

C3 Capacitor, 1µF 16V

C4 Capacitor, 10nF 16V

C5 Capacitor, 1 ~ 10 µF 16V

C6 Capacitor, 0.1 ~ 1µF 16V

C7 Capacitor, 15nF 16V

SSD1303 Rev 1.7 P 21/56 May 2005 S o l o m on S ystech

8 COMMAND TABLE

Table 4 - Command table

(D/C =0, R/W (WR#)=0, E (RD#)=1)

Note: commands marked with “**” are compatible to SSD1301

D/C Hex D7 D6 D5 D4 D3 D2 D1 D0 Command Description

0 0 0 0 0 X3 X

2 X

1 X

00~0F

Set Lower Colum n

Address ** Set the l ower nibble of the column address register

using X3X2X1X0 as data bit s. The initial di splay line

0 10~1F 0 0 0 1 X3 X

2 X

1 X

0 Set Higher Column

Address ** Set the hi gher ni bbl e of the column address register

using X3X2X1X0 as data bit s. The initial di splay line

0 26 0 0 1 0 0 1 1 0 Horizontal scroll setup A[2:0] Set the number of colum n scroll per st ep

0 A[2:0] * * * * * A2 A

1 A

0 Valid val ue: 001b, 010b, 011b, 100b

0 B[2:0] * * * * * B2 B

1 B

0 B[2:0] Define st art page address

0 C[1:0] * * * * * * C1 C

0 C[1:0] Set time interval between each scroll step in

term s of fram e f requency

0 D[2:0] * * * * * D2 D

1 D

00b – 12 frame

01b – 64 frames

10b – 128 f rames

11b – 256 f rames

D[ 2: 0] Define end page address

Set the value of D[2:0] l arger or equal to B[2:0]

0 0 0 1 0 1 1 1 1

2F Acti vate horizontal sc rol l Start hori zont al scrolling

0 0 0 1 0 1 1 1 0

2E Deactivate horizontal

scroll Stop horizontal scrolling

0 40-7F 0 1 X5 X

4 X

3 X

2 X

1 X

0 Set Displ ay Start Line Set display TA M display start line register from 0-63

using X5X3X2X1X0.

Display start line register is reset to 000000 during

POR

0 81 1 0 0 0 0 0 0 1

0 A[7:0] A7 A

6 A

5 A

4 A

3 A

2 A

1 A

0 Set Contras t Control

steps . Contrast inc reases as the value i ncreases.

(POR = 80h)

0 82 1 0 0 0 0 0 1 0

0 A[7:0] A7 A

6 A

5 A

4 A

3 A

2 A

1 A

Brightnes s for color

banks Double byte command to select 1 out of 256

brightness steps. Brightness i ncreases as t he val ue

increases. (POR = 80h)

0 91 1 0 0 1 0 0 0 1 Set current drive pulse width of Bank 0, Colour A, B

and C.

0 X[5:0] * * X5 X

4 X

3 X

2 X

1 X

0 Bank 0: X[5:0] = 0… 63; for pulse width set to 1 ~

64 clocks (POR = 110001b)

0 A[5:0] * * A5 A

4 A

3 A

2 A

1 A

0 Colour A: A[5:0] same as above (POR = 111111b)

0 B[5:0] * * B5 B

4 B

3 B

2 B

1 B

0 Colour B: B[5:0] same as above (POR = 111111b)

0 C[5:0] * * C5 C

4 C

3 C

2 C

1 C

0 Colour C: C[5: 0] same as above (POR = 111111b)

Set Look Up Tabl e

(LUT) for area colour

Note: colour D pulse width is fixed at 64 clocks

pulse .

Solomon S ystech May 2005 P 22/56 Rev 1.7 SSD1303

D/C Hex D7 D6 D5 D4 D3 D2 D1 D0 Command Description

0 92 1 0 0 1 0 0 1 0 A[1:0] : 00, 01, 10, or 11 for Colour = A, B, C or D of

bank 1

0 A[7:0] A7 A

6 A

5 A

4 A

3 A

2 A

1 A

0 A[3:2] : 00, 01, 10, or 11 for Colour = A , B, C or D

of bank 2

0 B[7:0] B7 B

6 B

5 B

4 B

3 B

2 B

1 B

0 :

0 C[7:0] C7 C

6 C

5 C

4 C

3 C

2 C

1 C

0 :

0 D[7:0] D7 D

6 D

5 D

4 D

3 D

2 D

1 D

0 D[7:6]: 00, 01, 10, or 11 for Col our = A, B, C or D of

bank 16

Set bank colour of for

bank 1-16 (Page 0)

0 93 1 0 0 1 0 0 1 1 A[1:0] : 00, 01, 10, or 11 for Colour = A, B, C or D of

bank 17

0 A[7:0] A7 A

6 A

5 A

4 A

3 A

2 A

1 A

0 A[3:2] : 00, 01, 10, or 11 for Colour = A , B, C or D

of bank 18

0 B[7:0] B7 B

6 B

5 B

4 B

3 B

2 B

1 B

0 :

0 C[7:0] C7 C

6 C

5 C

4 C

3 C

2 C

1 C

0 :

0 D[7:0] D7 D

6 D

5 D

4 D

3 D

2 D

1 D

0 D[7:6]: 00, 01, 10, or 11 for Col our = A, B, C or D of

bank 32

Set bank colour of for

bank 17-32 (Page 1)

X0=0: column address 0 is mapped to SEG0 (POR) 0 A0~ A1 1 0 1 0 0 0 0 X0 S et Segment Re-map **

X0=1: column address 131 is mapped t o SEG0

X0=0: normal displ ay (POR)

X0=1: entire display ON

0 A4~A5 1 0 1 0 0 1 0 X0 Set Entire Display

ON/OFF **

X0=0: normal displ ay (POR) 0 A6~A7 1 0 1 0 0 1 1 X0 Set Normal/Inverse

Display ** X0=1: inverse display

0 A8 1 0 1 0 1 0 0 0

0 A[5:0] * * A5 A

4 A

3 A

2 A

1 A

0 Set Multiplex Ratio ** The next command, A [5:0] determines multiplex ratio

N from 16MUX-64MUX, POR= 64MUX

0 AA 1 0 1 0 1 0 1 0 NOP Reserved, do not use

0 1

1 1

NOP Reserved, do not use

0 AD

1 0

0 1

0 0

0 1

1 1

0 0

1 1

X0 Set DC-DC on/off

X0 : 1 DC-DC will be turned on when display on

(POR)

0 DC-DC is disabl e

X0=0: turns OFF OLED panel (POR) 0 AE~AF 1 0 1 0 1 1 1 X0 Set Display ON/OFF ** X0=1: turns ON OLE D panel

0 B0~BF 1 0 1 1 X3 X

2 X

1 X

0 Set Page Address ** S et GDDRAM Page Address (0~7) for read/write

using X3X2X1X0

0 C0/C8 1 1 0 0 X3 * * * Set COM Output Sc an

Direction ** X3=0: normal mode (POR) Scan from COM 0 to COM

[N –1]

X3=1: remapped mode. Scan f rom COM [N-1] to

COM0

Where N is the Mult i pl ex ratio.

0 D0-D1 1 1 0 1 0 0 0 X0 Reserved Reserved, do not use

SSD1303 Rev 1.7 P 23/56 May 2005 S o l o m on S ystech

D/C Hex D7 D6 D5 D4 D3 D2 D1 D0 Command Description

0 D3 1 1 0 1 0 0 1 1 Set vertical scroll by COM from 0-63.

0 A[5:0] * * A5 A

4 A

3 A

2 A

1 A

0 Set Display Offset ** The value is reset to 00H aft er P O R.

0 D5 1 1 0 1 0 1 0 1 Set Display Clock

Divide Ratio/Oscillator

Frequency

A[3:0] Define the divide ratio of the display clocks

(DCLK):

0 A[7:0] A7 A

6 A

5 A

4 A

3 A

2 A

1 A

0 Divide rat i o= A [3:0] + 1, POR i s 0000b (divide ratio =

A[ 7: 4] Set the Oscillat or Frequenc y. Os cillator

Frequency increases with the value of A[7:4] and vice

versa. P OR i s 0111b

0 D8 1 1 0 1 1 0 0 0 X5X4= 00 (POR) : mono m ode

0 0

X5 X

4 0 X2 0 X0 Set area colour m ode

on/off & low power

display mode X5X4= 11 Area Colour enable

X2=0 and X0=0: Normal (POR) power mode

X2=1 and X0=1: Set low power save mode

0 D9 1 1 0 1 1 0 0 1 Set Pre-charge period** A[3:0] Phase 1 period of up to 15 dclk clocks

[POR=2h]; 0 is invalid entry

0 A[7:0] A7 A

6 A

5 A

4 A

3 A

2 A

1 A

0 A[7:4] Phase 2 period of up to 15 dclk clocks

[POR=2h]; 0 is invalid entry

0 DA 1 1 0 1 1 0 1 0 X4=0, Sequential COM pin conf i gurat i on

0 0 0 0 X4 0 0 1 0 (i.e. COM31, 30, 29….0 ; SEG0-132;

COM31,32….62,63)

X4=1(POR), Alt ernative COM pin configurati on

Set COM pins hardware

configuration

(i.e. COM62,60, 58,…2,0; SEG0-132;

COM1,3,5…61,63)

0 DB 1 1 0 1 1 0 1 1 Set VCOM Deselect

Level A[6:0] 0000000 l ow VCOM deselect level (~ 0.43

Vref)

0 A[6:0] * A6 A

5 A

4 A

3 A

2 A

1 A

0 0110101 norm al V COM desel ect level (~ 0.77*Vref

(POR))

1111111 high V COM des el ect level (equal Vref )

0 E2 1 1 1 0 0 0 1 0 Reserved Reserved

0 E3 1 1 1 0 0 0 1 1 NOP ** Command for No Operation

0 F* 1 1 1 1 * * * *

Reserved Reserved, do not use

Note: Remark “*” stands for “Don’t Care”

Table 5 - Read command table

Solomon S ystech May 2005 P 24/56 Rev 1.7 SSD1303

(D/C=0, R/W (WR#)=1, E (RD#)=1 for 6800 or E (RD#)=0 for 8080)

Bit Pattern Command Description

D7D6D5D4D3D2D1D0

Status Register Read *

D7 : Reserve

D6 : “1” for display OFF / “0” for display ON

D5 : Reserve

D4 : Reserve

D3 : Reserve

D2 : Reserve

D1 : Reserve

D0 : Reserve

Note: Patterns other than that given in Command Table are prohibited to enter to the chip as a command; otherwise, unexpected result

will occur.

8.1 Data Read / Writ e

To read data f rom the GDDRAM, input HIGH to R/W (WR#) pin and D/C pin for 6800-series parallel m ode,

LOW to E (RD#) pin and HIGH to D/C# pin f or 8080-s eries parallel m ode. No data r ead is provided in s erial

mode operation.

In normal data read mode, GDDRAM column address pointer will be increased by one automatically after

each data read.

Also, a dummy read is required before the first data read. See Figure 5 in Functional Block Description.

To write data to the GDDRAM, input LOW to R/W (W R#) pin and HIGH to D/C pin for 6800-series parallel

mode AND 8080-series parallel mode. For serial interface mode, it is always in write mode. GDDRAM

column address pointer will be increased by one automatically after each data write.

Table 6 - Address increment table (Automatic)

D/C

R/W (WR#)

Comment

Address I ncrement

0 0 Write Command No

0 1 Read Status No

1 0 Write Data Yes

1 1 Read Data Yes*1

*1. If read-data command is issued in read-modify-write mode, address increase is not applied.

SSD1303 Rev 1.7 P 25/56 May 2005 S o l o m on S ystech

9 COMMAND DESCRIPTIONS

Set Lower Column Address

This com mand spec ifies the lower nibble of the 8-bit c olumn addres s of the display data RAM. The colum n

address will be incremented by each data access after it is pre-set by the MCU.

Set Higher Column Address

This comm and s pecif ies the higher nibble of the 8- bit colum n addres s of the display data RAM. The colum n

address will be incremented by each data access after it is pre-set by the MCU.

Activate Horizontal Scroll

Start motion of horizontal scrolling. This command should only be issued after Horizontal scroll setup

parameters are defined.

The following actions are prohibited after the horizontal scroll is activated

1. RAM access (Data write or read)

2. Changing horizontal scroll setup parameters

The SSD1303 horizontal scroll is designed for 128 columns scrolling only. 4 remaining columns are

reserved for computation and should be left open.

With column address 0 mapped to SEG0 (Segment remap setting = A0h), the 4 unused columns will be

SEG128, SEG129, SEG130, SEG131.

W ith column address 0 m apped to SEG131 (Segment rem ap setting = A1h), the 4 unused colum ns will be

SEG0, SEG1, SEG2, SEG3.

Figure 8 - Horizontal scroll dir ection

REMAP

SETTING

SEG0

SEG1

SEG2

SEG3

SEG4

SEG5

…

SEG126

SEG127

SEG128

SEG129

SEG130

SEG131

A0 A B C D E F ! ! ! Y Z Invalid data

A1 Invalid data Z Y " " " F E D C B A

Scroll direction

Solomon S ystech May 2005 P 26/56 Rev 1.7 SSD1303

Deactivate Horizontal Scroll

Stop motion of horizontal scrolling.

Horizontal Scroll Setup

This comm and cons ists of 5 c onsecutive bytes to set up the horizontal scroll param eters . It determined the

scrolling start page, end page and the scrolling speed.

Before issuing this com m and, the horizontal scr oll mus t be deactivated (2Eh). O therwise, ram content m ay

be corrupted.

Set Display Start Line

This command is to set Display Start Line register to determine starting address of display RAM to be

displayed by selecting a value from 0 to 63. With value equals to 0, D0 of Page 0 is m apped to COM0. With

value equals to 1, D1 of Page0 is m apped to COM0. T he display start line values of 0 to 63 are as signed to

Page 0 to 7.

Set Contrast Control Register

This comm and is to s et Contrast Setting of the dis play. The chip has 256 contrast steps from 00 to FF. The

segment output current increases as the contrast step value increases. See Figure 9.

Figure 9 - Segment current vs Contrast setting

Segment current vs Contr as t set tin

100

150

200

250

300

350

00 0F 1F 2F 3F 4F 5F 6F 7F 8F 9F AF BF CF DF EF FF

Contr ast set t in g

C urrent (uA)

Set Brightness for Color Banks

This command is to set Brightness Setting of the display for area colors banks (except bank 0). The chip

has 256 brightness steps from 00 to FF. The segment output current increases as the brightness step value

increases

Segment output current setting:

Iseg = Cr/256 * Iref * scale factor

Where:

Cr is contrast st ep

Iref is reference current equals 10uA

Scale f actor =32

SSD1303 Rev 1.7 P 27/56 May 2005 S o l o m on S ystech

Set Look Up Table (LUT) for area colour

SSD1303 provides 4 colour (pulse width) settings - Colour A, B, C and D. The colour intensity (or grey

scale) is defined by the current drive pulse width. The pulse width of colour A, B, C can be programmable

from 1 to 64 DCLK* duration. The colour D is fixed at 64 DCLK pulse width. This colour setting has to be

stored in the Look Up Table (LUT).

For the background colour, the colour intensity is defined by a variable X[5:0].

Set LUT command: 10010001

X[5:0]

A[5:0]

B[5:0]

C[5:0]

Description Number of

DCLKs

Bank 0 Set background colour X[5:0]

Colour A Set Pulse Wi dth A A[5:0]

Colour B Set Pulse Wi dth B B[5:0]

Colour C Set Pulse Width C C[5:0]

Colour D Pulse width D is fixed to 64

DCLK 64 (fixed)

DCLK: Internal Display Clock

Set bank colour of bank 1-16 (Page 0) and bank colour of bank 17-32 (Page 1)

Next step is to define the c olour of eac h display area. The 132x64 display matrix is divided into 8 pages of 8

commons per pages. The first two pages, page 0 and page 1, are divided into 32 banks: Bank16 and

Bank32 c omprise of a dis play area of 12x8 pixels. O ther banks (0~15 & 17~31) have matrices of 8x 8 pix els.

Each bank can be pr ogramm able to any 1 of the 4 colour (A, B, C, D) . User c an use 92h and 93h c omm and

for the bank colour setting. Note: Only applicable in area colour mode.

Set Segment Re-map

This command changes the mapping between the display data column address and segment driver. It

allows flexibility in OLED module design. Refer to Command Table.

Set Entire Display ON/OFF

This com m and f orces the entire display to be “ON” regardles s of the contents of the display data RAM. This

command has priority over normal/reverse display. This command will be used with “Set Display ON/OFF”

command to form a compound command for entering power save mode.

Set Normal/Inverse Display

This command sets the display to be either normal/inverse. In normal display, a RAM data of 1 indicates an

“ON” pixel while in inverse display; a RAM data of 0 indicates an “ON” pixel.

Set Multiplex Ratio

This command switches default 63 multiplex mode to any multiplex ratio from 2 to 63. The output pads

COM0-COM63 will be switched to corresponding COM signal.

Set DC-DC on/off

This command is to control the DC-DC voltage converter. The converter will be turned on by issuing this

command then DISPLAY ON command. The panel display must be off while issuing this command.

POR the DC-DC will be turned on.

Solomon S ystech May 2005 P 28/56 Rev 1.7 SSD1303

Set Display ON/OFF

This command turns the display ON or OFF. When the display is OFF, the segment and common output

are in high impedance state.

Set Page Address

This command positions the page address from 0 to 7 in GDDRAM. Refer to Command Table.

Set COM Output Scan Direction

This comm and sets the scan dir ection of the COM output allowing layout flexibility in OLED module design.

In addition, the display will have im m ediate effec t once this com mand is is sued. That is, if this com mand is

sent during normal display, the graphic display will be vertically flipped.

Set Display Offset

This is a double byte command. The next command specifies the mapping of display start line to one of

COM0-63 (it is assumed that COM0 is the display start line, display start line register equals to 0).

For ex ample, to move the COM16 towards the COM0 dir ection for 16 lines, the 6-bit data in the s econd byte

should be given by 010000. To m ove in the opposite direction by 16 lines, the 6-bit data should be given by

(64 – 16) and so the second byte should be 100000.

SSD1303 Rev 1.7 P 29/56 May 2005 S o l o m on S ystech

Set MUX ratio(A8)

COM Normal / Remapped (C0 / C8)

Display of fset (D3)

Display start line (40 - 7F)

COM0 Row0 RAM0 Row8 RAM8 Row0 RAM8 Row0 RAM0 Row8 RAM8 Row0 RAM8

COM1 Row1 RAM1 Row9 RAM9 Row1 RAM9 Row1 RAM1 Row9 RAM9 Row1 RAM9

COM2 Row2 RAM2 Row10 RAM10 Row2 RAM10 Row2 RAM2 Row10 RAM10 Row2 RAM10

COM3 Row3 RAM3 Row11 RAM11 Row3 RAM11 Row3 RAM3 Row11 RAM11 Row3 RAM11

COM4 Row4 RAM4 Row12 RAM12 Row4 RAM12 Row4 RAM4 Row12 RAM12 Row4 RAM12

COM5 Row5 RAM5 Row13 RAM13 Row5 RAM13 Row5 RAM5 Row13 RAM13 Row5 RAM13

COM6 Row6 RAM6 Row14 RAM14 Row6 RAM14 Row6 RAM6 Row14 RAM14 Row6 RAM14

COM7 Row7 RAM7 Row15 RAM15 Row7 RAM15 Row7 RAM7 Row15 RAM15 Row7 RAM15

COM8 Row8 RAM8 Row16 RAM16 Row8 RAM16 Row8 RAM8 Row16 RAM16 Row8 RAM16

COM9 Row9 RAM9 Row17 RAM17 Row9 RAM17 Row9 RAM9 Row17 RAM17 Row9 RAM17

COM10 Row10 RAM10 Row18 RAM18 Row10 RAM18 Row10 RAM10 Row18 RAM18 Row10 RAM18

COM11 Row11 RAM11 Row19 RAM19 Row11 RAM19 Row11 RAM11 Row19 RAM19 Row11 RAM19

COM12 Row12 RAM12 Row20 RAM20 Row12 RAM20 Row12 RAM12 Row20 RAM20 Row12 RAM20

COM13 Row13 RAM13 Row21 RAM21 Row13 RAM21 Row13 RAM13 Row21 RAM21 Row13 RAM21

COM14 Row14 RAM14 Row22 RAM22 Row14 RAM22 Row14 RAM14 Row22 RAM22 Row14 RAM22

COM15 Row15 RAM15 Row23 RAM23 Row15 RAM23 Row15 RAM15 Row23 RAM23 Row15 RAM23

COM16 Row16 RAM16 Row24 RAM24 Row16 RAM24 Row16 RAM16 Row24 RAM24 Row16 RAM24

COM17 Row17 RAM17 Row25 RAM25 Row17 RAM25 Row17 RAM17 Row25 RAM25 Row17 RAM25

COM18 Row18 RAM18 Row26 RAM26 Row18 RAM26 Row18 RAM18 Row26 RAM26 Row18 RAM26

COM19 Row19 RAM19 Row27 RAM27 Row19 RAM27 Row19 RAM19 Row27 RAM27 Row19 RAM27

COM20 Row20 RAM20 Row28 RAM28 Row20 RAM28 Row20 RAM20 Row28 RAM28 Row20 RAM28

COM21 Row21 RAM21 Row29 RAM29 Row21 RAM29 Row21 RAM21 Row29 RAM29 Row21 RAM29

COM22 Row22 RAM22 Row30 RAM30 Row22 RAM30 Row22 RAM22 Row30 RAM30 Row22 RAM30

COM23 Row23 RAM23 Row31 RAM31 Row23 RAM31 Row23 RAM23 Row31 RAM31 Row23 RAM31

COM24 Row24 RAM24 Row32 RAM32 Row24 RAM32 Row24 RAM24 Row32 RAM32 Row24 RAM32

COM25 Row25 RAM25 Row33 RAM33 Row25 RAM33 Row25 RAM25 Row33 RAM33 Row25 RAM33

COM26 Row26 RAM26 Row34 RAM34 Row26 RAM34 Row26 RAM26 Row34 RAM34 Row26 RAM34

COM27 Row27 RAM27 Row35 RAM35 Row27 RAM35 Row27 RAM27 Row35 RAM35 Row27 RAM35

COM28 Row28 RAM28 Row36 RAM36 Row28 RAM36 Row28 RAM28 Row36 RAM36 Row28 RAM36

COM29 Row29 RAM29 Row37 RAM37 Row29 RAM37 Row29 RAM29 Row37 RAM37 Row29 RAM37

COM30 Row30 RAM30 Row38 RAM38 Row30 RAM38 Row30 RAM30 Row38 RAM38 Row30 RAM38

COM31 Row31 RAM31 Row39 RAM39 Row31 RAM39 Row31 RAM31 Row39 RAM39 Row31 RAM39

COM32 Row32 RAM32 Row40 RAM40 Row32 RAM40 Row32 RAM32 Row40 RAM40 Row32 RAM40

COM33 Row33 RAM33 Row41 RAM41 Row33 RAM41 Row33 RAM33 Row41 RAM41 Row33 RAM41

COM34 Row34 RAM34 Row42 RAM42 Row34 RAM42 Row34 RAM34 Row42 RAM42 Row34 RAM42

COM35 Row35 RAM35 Row43 RAM43 Row35 RAM43 Row35 RAM35 Row43 RAM43 Row35 RAM43

COM36 Row36 RAM36 Row44 RAM44 Row36 RAM44 Row36 RAM36 Row44 RAM44 Row36 RAM44

COM37 Row37 RAM37 Row45 RAM45 Row37 RAM45 Row37 RAM37 Row45 RAM45 Row37 RAM45

COM38 Row38 RAM38 Row46 RAM46 Row38 RAM46 Row38 RAM38 Row46 RAM46 Row38 RAM46

COM39 Row39 RAM39 Row47 RAM47 Row39 RAM47 Row39 RAM39 Row47 RAM47 Row39 RAM47

COM40 Row40 RAM40 Row48 RAM48 Row40 RAM48 Row40 RAM40 Row48 RAM48 Row40 RAM48

COM41 Row41 RAM41 Row49 RAM49 Row41 RAM49 Row41 RAM41 Row49 RAM49 Row41 RAM49

COM42 Row42 RAM42 Row50 RAM50 Row42 RAM50 Row42 RAM42 Row50 RAM50 Row42 RAM50

COM43 Row43 RAM43 Row51 RAM51 Row43 RAM51 Row43 RAM43 Row51 RAM51 Row43 RAM51

COM44 Row44 RAM44 Row52 RAM52 Row44 RAM52 Row44 RAM44 Row52 RAM52 Row44 RAM52

COM45 Row45 RAM45 Row53 RAM53 Row45 RAM53 Row45 RAM45 Row53 RAM53 Row45 RAM53

COM46 Row46 RAM46 Row54 RAM54 Row46 RAM54 Row46 RAM46 Row54 RAM54 Row46 RAM54

COM47 Row47 RAM47 Row55 RAM55 Row47 RAM55 Row47 RAM47 Row55 RAM55 Row47 RAM55

COM48 Row48 RAM48 Row56 RAM56 Row48 RAM56 Row48 RAM48 - - Row48 RAM56

COM49 Row49 RAM49 Row57 RAM57 Row49 RAM57 Row49 RAM49 - - Row49 RAM57

COM50 Row50 RAM50 Row58 RAM58 Row50 RAM58 Row50 RAM50 - - Row50 RAM58

COM51 Row51 RAM51 Row59 RAM59 Row51 RAM59 Row51 RAM51 - - Row51 RAM59

COM52 Row52 RAM52 Row60 RAM60 Row52 RAM60 Row52 RAM52 - - Row52 RAM60

COM53 Row53 RAM53 Row61 RAM61 Row53 RAM61 Row53 RAM53 - - Row53 RAM61

COM54 Row54 RAM54 Row62 RAM62 Row54 RAM62 Row54 RAM54 - - Row54 RAM62

COM55 Row55 RAM55 Row63 RAM63 Row55 RAM63 Row55 RAM55 - - Row55 RAM63

COM56 Row56 RAM56 Row0 RAM0 Row56 RAM0 - - Row0 RAM0 - -

COM57 Row57 RAM57 Row1 RAM1 Row57 RAM1 - - Row1 RAM1 - -

COM58 Row58 RAM58 Row2 RAM2 Row58 RAM2 - - Row2 RAM2 - -

COM59 Row59 RAM59 Row3 RAM3 Row59 RAM3 - - Row3 RAM3 - -

COM60 Row60 RAM60 Row4 RAM4 Row60 RAM4 - - Row4 RAM4 - -

COM61 Row61 RAM61 Row5 RAM5 Row61 RAM5 - - Row5 RAM5 - -

COM62 Row62 RAM62 Row6 RAM6 Row62 RAM6 - - Row6 RAM6 - -

COM63 Row63 RAM63 Row7 RAM7 Row63 RAM7 - - Row7 RAM7 - -

080

008

56 56 56

Normal Normal Normal

Normal

Output

Hardware

pin name 0

Normal

64 64

Normal

Solomon S ystech May 2005 P 30/56 Rev 1.7 SSD1303

Set MUX ratio(A8)

COM Normal / Remapped (C 0 / C8)

Display offset (D3)

Disp l a y start l i ne (4 0 - 7 F )

COM0 Row63 RAM63 Row7 RAM7 Row63 RAM7 Row47 RAM47 - - Row47 RAM41 - -

COM1 Row62 RAM62 Row6 RAM6 Row62 RAM6 Row46 RAM46 - - Row46 RAM40 - -

COM2 Row61 RAM61 Row5 RAM5 Row61 RAM5 Row45 RAM45 - - Row45 RAM41 - -

COM3 Row60 RAM60 Row4 RAM4 Row60 RAM4 Row44 RAM44 - - Row44 RAM42 - -

COM4 Row59 RAM59 Row3 RAM3 Row59 RAM3 Row43 RAM43 - - Row43 RAM43 - -

COM5 Row58 RAM58 Row2 RAM2 Row58 RAM2 Row42 RAM42 - - Row42 RAM44 - -

COM6 Row57 RAM57 Row1 RAM1 Row57 RAM1 Row41 RAM41 - - Row41 RAM45 - -

COM7 Row56 RAM56 Row0 RAM0 Row56 RAM0 Row40 RAM40 - - Row40 RAM46 - -

COM8 Row55 RAM55 Row63 RAM63 Row55 RAM63 Row39 RAM39 Row47 RAM47 Row39 RAM47 Row47 RAM63

COM9 Row54 RAM54 Row62 RAM62 Row54 RAM62 Row38 RAM38 Row46 RAM46 Row38 RAM46 Row46 RAM62

COM10 Row53 RAM53 Row61 RAM61 Row53 RAM61 Row37 RAM37 Row45 RAM45 Row37 RAM45 Row45 RAM61

COM11 Row52 RAM52 Row60 RAM60 Row52 RAM60 Row36 RAM36 Row44 RAM44 Row36 RAM44 Row44 RAM60

COM12 Row51 RAM51 Row59 RAM59 Row51 RAM59 Row35 RAM35 Row43 RAM43 Row35 RAM43 Row43 RAM59

COM13 Row50 RAM50 Row58 RAM58 Row50 RAM58 Row34 RAM34 Row42 RAM42 Row34 RAM42 Row42 RAM58

COM14 Row49 RAM49 Row57 RAM57 Row49 RAM57 Row33 RAM33 Row41 RAM41 Row33 RAM41 Row41 RAM57

COM15 Row48 RAM48 Row56 RAM56 Row48 RAM56 Row32 RAM32 Row40 RAM40 Row32 RAM40 Row40 RAM56

COM16 Row47 RAM47 Row55 RAM55 Row47 RAM55 Row31 RAM31 Row39 RAM39 Row31 RAM39 Row39 RAM55

COM17 Row46 RAM46 Row54 RAM54 Row46 RAM54 Row30 RAM30 Row38 RAM38 Row30 RAM38 Row38 RAM54

COM18 Row45 RAM45 Row53 RAM53 Row45 RAM53 Row29 RAM29 Row37 RAM37 Row29 RAM37 Row37 RAM53

COM19 Row44 RAM44 Row52 RAM52 Row44 RAM52 Row28 RAM28 Row36 RAM36 Row28 RAM36 Row36 RAM52

COM20 Row43 RAM43 Row51 RAM51 Row43 RAM51 Row27 RAM27 Row35 RAM35 Row27 RAM35 Row35 RAM51

COM21 Row42 RAM42 Row50 RAM50 Row42 RAM50 Row26 RAM26 Row34 RAM34 Row26 RAM34 Row34 RAM50

COM22 Row41 RAM41 Row49 RAM49 Row41 RAM49 Row25 RAM25 Row33 RAM33 Row25 RAM33 Row33 RAM49

COM23 Row40 RAM40 Row48 RAM48 Row40 RAM48 Row24 RAM24 Row32 RAM32 Row24 RAM32 Row32 RAM48

COM24 Row39 RAM39 Row47 RAM47 Row39 RAM47 Row23 RAM23 Row31 RAM31 Row23 RAM31 Row31 RAM47

COM25 Row38 RAM38 Row46 RAM46 Row38 RAM46 Row22 RAM22 Row30 RAM30 Row22 RAM30 Row30 RAM46

COM26 Row37 RAM37 Row45 RAM45 Row37 RAM45 Row21 RAM21 Row29 RAM29 Row21 RAM29 Row29 RAM45

COM27 Row36 RAM36 Row44 RAM44 Row36 RAM44 Row20 RAM20 Row28 RAM28 Row20 RAM28 Row28 RAM44

COM28 Row35 RAM35 Row43 RAM43 Row35 RAM43 Row19 RAM19 Row27 RAM27 Row19 RAM27 Row27 RAM43

COM29 Row34 RAM34 Row42 RAM42 Row34 RAM42 Row18 RAM18 Row26 RAM26 Row18 RAM26 Row26 RAM42

COM30 Row33 RAM33 Row41 RAM41 Row33 RAM41 Row17 RAM17 Row25 RAM25 Row17 RAM25 Row25 RAM41

COM31 Row32 RAM32 Row40 RAM40 Row32 RAM40 Row16 RAM16 Row24 RAM24 Row16 RAM24 Row24 RAM40

COM32 Row31 RAM31 Row39 RAM39 Row31 RAM39 Row15 RAM15 Row23 RAM23 Row15 RAM23 Row23 RAM39

COM33 Row30 RAM30 Row38 RAM38 Row30 RAM38 Row14 RAM14 Row22 RAM22 Row14 RAM22 Row22 RAM38

COM34 Row29 RAM29 Row37 RAM37 Row29 RAM37 Row13 RAM13 Row21 RAM21 Row13 RAM21 Row21 RAM37

COM35 Row28 RAM28 Row36 RAM36 Row28 RAM36 Row12 RAM12 Row20 RAM20 Row12 RAM20 Row20 RAM36

COM36 Row27 RAM27 Row35 RAM35 Row27 RAM35 Row11 RAM11 Row19 RAM19 Row11 RAM19 Row19 RAM35

COM37 Row26 RAM26 Row34 RAM34 Row26 RAM34 Row10 RAM10 Row18 RAM18 Row10 RAM18 Row18 RAM34

COM38 Row25 RAM25 Row33 RAM33 Row25 RAM33 Row9 RAM9 Row17 RAM17 Row9 RAM17 Row17 RAM33

COM39 Row24 RAM24 Row32 RAM32 Row24 RAM32 Row8 RAM8 Row16 RAM16 Row8 RAM16 Row16 RAM32

COM40 Row23 RAM23 Row31 RAM31 Row23 RAM31 Row7 RAM7 Row15 RAM15 Row7 RAM15 Row15 RAM31

COM41 Row22 RAM22 Row30 RAM30 Row22 RAM30 Row6 RAM6 Row14 RAM14 Row6 RAM14 Row14 RAM30

COM42 Row21 RAM21 Row29 RAM29 Row21 RAM29 Row5 RAM5 Row13 RAM13 Row5 RAM13 Row13 RAM29

COM43 Row20 RAM20 Row28 RAM28 Row20 RAM28 Row4 RAM4 Row12 RAM12 Row4 RAM12 Row12 RAM28

COM44 Row19 RAM19 Row27 RAM27 Row19 RAM27 Row3 RAM3 Row11 RAM11 Row3 RAM11 Row11 RAM27

COM45 Row18 RAM18 Row26 RAM26 Row18 RAM26 Row2 RAM2 Row10 RAM10 Row2 RAM10 Row10 RAM26

COM46 Row17 RAM17 Row25 RAM25 Row17 RAM25 Row1 RAM1 Row9 RAM9 Row1 RAM9 Row9 RAM25

COM47 Row16 RAM16 Row24 RAM24 Row16 RAM24 Row0 RAM0 Row8 RAM8 Row0 RAM8 Row8 RAM24

COM48 Row15 RAM15 Row23 RAM23 Row15 RAM23 - - Row7 RAM7 - - Row7 RAM23

COM49 Row14 RAM14 Row22 RAM22 Row14 RAM22 - - Row6 RAM6 - - Row6 RAM22

COM50 Row13 RAM13 Row21 RAM21 Row13 RAM21 - - Row5 RAM5 - - Row5 RAM21

COM51 Row12 RAM12 Row20 RAM20 Row12 RAM20 - - Row4 RAM4 - - Row4 RAM20

COM52 Row11 RAM11 Row19 RAM19 Row11 RAM19 - - Row3 RAM3 - - Row3 RAM19

COM53 Row10 RAM10 Row18 RAM18 Row10 RAM18 - - Row2 RAM2 - - Row2 RAM18

COM54 Row9 RAM9 Row17 RAM17 Row9 RAM17 - - Row1 RAM1 - - Row1 RAM17

COM55 Row8 RAM8 Row16 RAM16 Row8 RAM16 - - Row0 RAM0 - - Row0 RAM16

COM56Row7RAM7Row15RAM15Row7RAM15--------

COM57Row6RAM6Row14RAM14Row6RAM14--------

COM58Row5RAM5Row13RAM13Row5RAM13--------

COM59Row4RAM4Row12RAM12Row4RAM12--------

COM60Row3RAM3Row11RAM11Row3RAM11--------

COM61Row2RAM2Row10RAM10Row2RAM10--------

COM62Row1RAM1Row9RAM9Row1RAM9--------

COM63Row0RAM0Row8RAM8Row0RAM8--------

Remap

48 48

Remap Remap

Remap

008

Hardware

pin name

Output

64 64 64

Remap Remap Remap

Set Display Clock Divide Ratio/ Oscillator Frequency

This com m and is us ed to s et the f requency of the internal display clock s, DCLKs. It is def ined as the divide

ratio (Value f rom 1 to 16) used to divide the oscillator f requency. POR is 1. Frame fr equency is determined

by divide ratio, number of display clocks per row, MUX ratio and oscillator frequency.

Set Area Colour Mode ON/OFF

This command is used to enable area colour mode. POR is mono mode.

SSD1303 Rev 1.7 P 31/56 May 2005 S o l o m on S ystech

Set Low Power Display Mode

This is a double byte command. This command is set to reduce power consumption during IC operation.

Set Pre-charge period

This command is used to set the duration of the pre-charge period. The interval is counted in number of

DCLK. POR is 2 DCLK.

Set COM pins hardware configuration

This command is to set the COM signals pin configuration (sequential or alternative) to match the OLED

panel hardware layout

Sequential COM pin configuration:

COM31, 30, 29…0 SEG0, 1, 2… 131 COM32, 33, 34…63

Alternative COM pin configuration (POR):

COM62, 60, 58…0 SEG0, 1, 2… 131 COM1, 3, 5…63

Set VCOM deselect level

This command is to set the COM pin output voltage level at deselect stage.

NOP

No Operation Command

Status register Read

This command is issued by setting D/C# LOW during a data read (refer to Figure 10 and Figure 11 for

parallel interface waveform). It allows the MCU to monitor the internal status of the chip. No status read is

provided for serial mode.

Solomon S ystech May 2005 P 32/56 Rev 1.7 SSD1303

10 MAXIMUM RATINGS

Table 7 - Maximum Ratings

(Voltage Reference to VSS)

Symbol Parameter Value Unit

VDD -0.3 to +4.0 V

VCC 0.0 to 18.0 V

VREF Supply Voltage 0.0 to 18.0 V

VCOMH Supply Voltage/Output voltage 0.0 to 18.0 V

- SEG/COM output voltage 0.0 to 18.0 V

Vin Input voltage Vss-0.3 to Vdd+0.3 V

TA Operating Temperature -40 to +90 ºC

Tstg Storage Temperature Range -65 to +150 ºC

Maximum Rat i ngs are those values beyond which damage to the device may occ ur. Functional operat i on should be restric ted to the

lim i ts in the Electrical Charac teristic s tables or Pi n Description.

SSD1303 Rev 1.7 P 33/56 May 2005 S o l o m on S ystech

11 DC CHARACTERISTICS

Table 8 - DC Characteristics

(Unless otherwise specified, Voltage Referenced to VSS, VDD = 2.4 to 3.5V, TA = 25°C)

Symbol Parameter Test Condition Min Typ Max Unit

VCC Operating Voltage - 7 12 16 V

VDD Logic Supply Voltage - 2.4 - 3.5 V

VDD Logic Supply Voltage (internal

DC/DC enable) - 3.0 - 3.5 V

VOH High Logic Output Level IOUT = 100uA, 3.3MHz 0.9*VDD - VDD V

VOL Low Logic Output Level IOUT = 100uA, 3.3MHz 0 - 0.1*VDD V

VIH High Logic Input Level IOUT = 100uA, 3.3MHz 0.8*VDD - VDD V

VIL Low Logic Input Level IOUT = 100uA, 3.3MHz 0 - 0.2*VDD V

ICC, SLEEP Sleep mode Current VDD=2.7V, display

OFF, No panel attached -10 - +10 uA

IDD, SLEEP Sleep mode Current VDD=2.7V, display

OFF, No panel attached -10 - +10 uA

ICC VCC Supply Current

VDD = 2.7V, VCC = 12V, IREF = 10uA

No loading, Display ON, All ON

Contrast = FF - 550 - uA

IDD

VDD Supply Current

VDD = 2.7V, VCC = 12V, IREF = 10uA

No loading, Display ON, All ON

Contrast = FF - 190 -

Contrast=FF 285 320 355

Contrast=AF - 220 -

Contrast=5F - 120 -

ISEG

Segment Output Current

VDD=2.7V, VCC=12V,

IREF=10uA, Display ON, Segment

pin under test is connected with a

20K resistive load to VSS Contrast=0F - 20 -

Dev Segment output current uniformity

Dev = (ISEG – IMID)/IMID

IMID = (IMAX + IMIN)/2

ISEG[0:131] = Segment

current at contrast = FF

- - ±3 %

Adj. Dev Adjacent pin output current

uniformity (contrast = FF) Adj Dev = (I[n]-I[n+1]) /

(I[n]+I[n+1]) - ±2.0 - %

VDD input=3V, L=22uH;

R1=450Kohm;

R2=50Kohm;

Icc = 20mA(loading)

11.0 12.0 13.0

Vcc

DC-DC converter output voltage

7 - 16

Pwr DC-DC converter output power VDD input=3V, L=22uH;

Vcc = 12V - - 400 mW

Solomon S ystech May 2005 P 34/56 Rev 1.7 SSD1303

12 AC CHARACTERISTICS

Table 9 - AC Characteristics

(Unless otherwise specified, Voltage Referenced to VSS, VDD = 2.4 to 3.5V, TA = 25°C.)

Symbol Parameter Test Condition Min Typ Max Unit

FOSC Oscillation Frequency of

Display Timing

Generator

Vdd = 2.7V

315 360 420 kHz

FFRM

Frame Frequency for 64

MUX Mode

132x64 Graphic Display Mode,

Display ON, Internal Oscillator

Enabled

FOSC X

1/(D*K*64)

Reset low pulse width

RES#

Reset complete time

D: divide rat i o (def ault value = 1)

K: number of display clocks (default value = 54)

Refer to command table (s et display clock divide ratio/oscillat or f req) f or detail description

SSD1303 Rev 1.7 P 35/56 May 2005 S o l o m on S ystech

Table 10 - 6800-Series MPU Parallel Interface Timing Characteristics

(VDD - VSS = 2.4 to 3.5V, TA = 25°C)

Symbol Parameter Min Typ Max Unit

tcycle Clock Cycle Time 300 - - ns

tAS Address Setup Time 0 - - ns

tAH Address Hold Time 0 - - ns

tDSW Write Data Setup Time 40 - - ns

tDHW Write Data Hold Time 7 - - ns

tDHR Read Data Hold Time 20 - - ns

tOH Output Disable Time - - 70 ns

tACC Access Time - - 140 ns

PWCSL Chip Select Low Pulse W i dth (read)

Chip Selec t Low Pulse Width (write) 120

60 - - ns

PWCSH Chip Select Hi gh Pulse Width (read)

Chip Selec t High Pulse Widt h (write) 60

60 - - ns

tR Rise Time - - 15 ns

tF Fall Time - - 15 ns

Figure 10 - 6800-series MPU parallel interface characteristics

D0~D7(WRITE)

D0~D7(READ)

CS#

R/W

PWCSL tR

tF t

DHW

tOH

tACC t

DHR

Valid Data

tDSW

Valid Data

tcycle PWCSH

tAH

tAS

D/C

Solomon S ystech May 2005 P 36/56 Rev 1.7 SSD1303

Table 11 - 8080-Series MPU Parallel Interface Timing Characteristics

(VDD - VSS = 2.4 to 3.5V, TA = 25°C)

Symbol Parameter Min Typ Max Unit

tcycle Clock Cycle Time 300 - - ns

tAS Address Setup Time 0 - - ns

tAH Address Hold Time 0 - - ns

tDSW Write Data Set up Ti me 40 - - ns

tDHW Write Data Hold Time 7 - - ns

tDHR Read Data Hold Time 20 - - ns

tOH Output Disable Time - - 70 ns

tACC Access Time - - 140 ns

PWCSL Chip Select Low Puls e Wi dt h (read)

Chip Selec t Low Pulse Width (write) 120

60 - - ns

PWCSH Chip Select High Pulse Widt h (read)

Chip Selec t High Pulse Widt h (write) 60

60 - - ns

tR Rise Time - - 15 ns

tF Fall Time - - 15 ns

Figure 11 - 8080-series MPU parallel interface characteristics

tDHR

Valid Data

tDSW

tDHW

PWCSL PWCSH

cycle

D0-D7

(Read data from driver)

D0-D7

(Write data to driver)

RD#

CS#

D/C

SSD1303 Rev 1.7 P 37/56 May 2005 S o l o m on S ystech

Table 12 - Serial Interface Timing Characteristics

(VDD - VSS = 2.4 t o 3.5V, TA = 25°C)

Symbol Parameter Min Typ Max Unit

tcycle

Clock Cycle Time 250

- - ns

tAS

Address S etup Time 150 - - ns

tAH

Address Hol d Ti me 150 - - ns

tCSS

Chip Select Setup Time 120 - - ns

tCSH

Chip Select Hold Time 60 - - ns

tDSW

Write Data Setup Ti me 100 - - ns

tDHW

Write Data Hold T i me 100 - - ns

tCLKL

Clock Low Tim e 100 - - ns

tCLKH

Clock Hi gh T i me 100 - - ns

Rise Time - - 15 ns

Fall Time - - 15 ns

Figure 12 - Serial interface characteristics

tAH tAS

D/C

Valid Data

tDHW

tCLKL

tDSW

tCLKH

tcycle

tCSS t

CSH

tF t

SDIN(D1)

CS#

SCLK(D0)

SDIN(D1)

CS#

SCLK(D0)

D6 D5 D4 D3 D2 D1 D0

Solomon S ystech May 2005 P 38/56 Rev 1.7 SSD1303

The configuration for 6800-parallel interface mode, externally VCC is shown in the following diagram:

(VDD=2.7V, VCC=VREF=12V, IREF=10uA)

Pin connected to MCU interface: D0~D7, E, R/W #, D/C#, CS#, RES#

Pin externally connec ted to VSS: BS0, VSS B

Pin inte rnal l y c onnected to VCC: V REF

GDR, RESE, VBREF, FB should be lef t open individually;

C1~ C3: 4.7uF

R1: 910kΩ, R1=(Voltage at IREF pin-VS S )/IREF

Voltage at IREF pin = VCC-3V

13 APPLICATION EXAMPLE

Figure 13 - Application Example (Block Diagram of SSD1303T3)

DISPLAY PANEL SIZE

96 x 64

COM62

COM60

COM2

COM0

SEG0

SEG95

COM1

COM3

COM61

COM63

SSD1303T3

VCC VCOMH IREF D7~D0 E (RD#) R/W# (W/R#) D/C# RES# CS# BS1 BS2 VDD VDDB GDR RESE FB VBREF VSS

D0~D7 E (RD#) R/W# (W/R#) D/C# RES# CS# BS1 BS2 VDD VSS

VSS

[GND]

Vcc

SSD1303 Rev 1.7 P 39/56 May 2005 S o l o m on S ystech

14 SSD1303T3R1 PACKAGE DETAILS

SSD1303T3R1 Pin Assignment

Figure 14 - SSD1303T3R1 pin assignment (Copper view, Normal TAB design)

Remark:

Use internal clock

VREF is connected to VCC

Support MCU interface: 8-bit 6800/8080 parallel interface and SPI

VSSB, BGGND are connected to VSS

BS0 is connected to VSS

Solomon S ystech May 2005 P 40/56 Rev 1.7 SSD1303

Table 13 - SSD1303T3R1 pin assignment

P in no. Pi n nam e P i n no. Pin name P i n no. Pi n nam e Pi n no. Pi n nam e

1 NC 61 COM8 121 SEG47 181 COM7

2 VSS 62 COM6 122 SEG48 182 COM9

3 GDR 63 COM4 123 SEG49 183 COM11

4 VDDB 64 COM2 124 SEG50 184 COM13

5 FB 65 COM0 125 SEG51 185 COM15

6 RESE 66 NC 126 SEG52 186 COM17

7 VBREF 67 NC 127 SEG53 187 COM19

8 GP0 68 NC 128 SEG54 188 COM21

9 GP1 69 NC 129 SEG55 189 COM23

10 NC 70 NC 130 SEG56 190 COM25

11 VDD1 71 NC 131 SEG57 191 COM27

12 BS1 72 NC 132 SEG58 192 COM29

13 BS2 73 NC 133 SEG59 193 COM31

14 NC 74 SEG0 134 SEG60 194 COM33

15 CS# 75 SEG1 135 SEG61 195 COM35

16 RES# 76 SEG2 136 SEG62 196 COM37

17 D/C 77 SEG3 137 SEG63 197 COM39

18 R/W 78 SEG4 138 SEG64 198 COM41

19 E/RD 79 SEG5 139 SEG65 199 COM43

20 D0 80 SEG6 140 SEG66 200 COM45

21 D1 81 SEG7 141 SEG67 201 COM47

22 D2 82 SEG8 142 SEG68 202 COM49

23 D3 83 SEG9 143 SEG69 203 COM51

24 D4 84 SEG10 144 SEG70 204 COM53

25 D5 85 SEG11 145 SEG71 205 COM55

26 D6 86 SEG12 146 SEG72 206 COM57

27 D7 87 SEG13 147 SEG73 207 COM59

28 IREF 88 SEG14 148 SEG74 208 COM61

29 VCOMH 89 SEG15 149 SEG75 209 COM63

30 VCC 90 SEG16 150 SEG76 210 NC

31 NC 91 SEG17 151 SEG77 211 NC

32 NC 92 SEG18 152 SEG78

33 NC 93 SEG19 153 SEG79

34 COM62 94 SEG20 154 SEG80

35 COM60 95 SEG21 155 SEG81

36 COM58 96 SEG22 156 SEG82

37 COM56 97 SEG23 157 SEG83

38 COM54 98 SEG24 158 SEG84

39 COM52 99 SEG25 159 SEG85

40 COM50 100 SEG26 160 SEG86

41 COM48 101 SEG27 161 SEG87

42 COM46 102 SEG28 162 SEG88

43 COM44 103 SEG29 163 SEG89

44 COM42 104 SEG30 164 SEG90

45 COM40 105 SEG31 165 SEG91

46 COM38 106 SEG32 166 SEG92

47 COM36 107 SEG33 167 SEG93

48 COM34 108 SEG34 168 SEG94

49 COM32 109 SEG35 169 SEG95

50 COM30 110 SEG36 170 NC

51 COM28 111 SEG37 171 NC

52 COM26 112 SEG38 172 NC

53 COM24 113 SEG39 173 NC

54 COM22 114 SEG40 174 NC

55 COM20 115 SEG41 175 NC

56 COM18 116 SEG42 176 NC

57 COM16 117 SEG43 177 NC

58 COM14 118 SEG44 178 COM1

59 COM12 119 SEG45 179 COM3

60 COM10 120 SEG46 180 COM5

SSD1303 Rev 1.7 P 41/56 May 2005 S o l o m on S ystech

SSD1303T3R1 TAB PACKAGE DIMENSIONS

SSD1303T3

SOLOMON

Solomon S ystech May 2005 P 42/56 Rev 1.7 SSD1303

SSD1303 Rev 1.7 P 43/56 May 2005 S o l o m on S ystech

15 SSD1303T6R1 PACKAGE DETAILS

SSD1303T6R1 Pin Assignment

Figure 15 - SSD1303T6R1 pin assignment (Copper view)

Remark:

Use internal clock

VREF is connected to VCC

Support MCU interface: 8-bit 6800/8080 parallel interface and SPI

VSSB, BGGND are connected to VSS

BS0 is connected to VSS

Solomon S ystech May 2005 P 44/56 Rev 1.7 SSD1303

Table 14 - SSD1303T6R1 pin assignment

P in no. P i n name P i n no. P in name Pi n no. Pi n name P i n no. P in name Pi n no. Pi n name

1 NC 61 COM9 121 SEG83 181 SEG23 241 COM50

2 VCC 62 COM7 122 SEG82 182 SEG22 242 COM52

3 VCOMH 63 COM5 123 SEG81 183 SEG21 243 COM54

4 IREF 64 COM3 124 SEG80 184 SEG20 244 COM56

5 D7 65 COM1 125 SEG79 185 SEG19 245 COM58

6 D6 66 NC 126 SEG78 186 SEG18 246 COM60

7 D5 67 NC 127 SEG77 187 SEG17 247 COM62

8 D4 68 NC 128 SEG76 188 SEG16 248 NC

9 D3 69 NC 129 SEG75 189 SEG15 249 NC

10 D2 70 NC 130 SEG74 190 SEG14

11 D1 71 NC 131 SEG73 191 SEG13

12 D0 72 NC 132 SEG72 192 SEG12

13 E/RD 73 SEG131 133 SEG71 193 SEG11

14 R/W 74 SEG130 134 SEG70 194 SEG10

15 D/C 75 SEG129 135 SEG69 195 SEG9

16 RES# 76 SEG128 136 SEG68 196 SEG8

17 CS# 77 SEG127 137 SEG67 197 SEG7

18 NC 78 SEG126 138 SEG66 198 SEG6

19 BS2 79 SEG125 139 SEG65 199 SEG5

20 BS1 80 SEG124 140 SEG64 200 SEG4

21 VDD 81 SEG123 141 SEG63 201 SEG3

22 NC 82 SEG122 142 SEG62 202 SEG2

23 NC 83 SEG121 143 SEG61 203 SEG1

24 NC 84 SEG120 144 SEG60 204 SEG0

25 VBREF 85 SEG119 145 SEG59 205 NC

26 RESE 86 SEG118 146 SEG58 206 NC

27 FB 87 SEG117 147 SEG57 207 NC

28 VDDB 88 SEG116 148 SEG56 208 NC

29 GDR 89 SEG115 149 SEG55 209 NC

30 VSS 90 SEG114 150 SEG54 210 NC

31 NC 91 SEG113 151 SEG53 211 NC

32 NC 92 SEG112 152 SEG52 212 NC

33 NC 93 SEG111 153 SEG51 213 NC

34 COM63 94 SEG110 154 SEG50 214 NC

35 COM61 95 SEG109 155 SEG49 215 NC

36 COM59 96 SEG108 156 SEG48 216 COM0

37 COM57 97 SEG107 157 SEG47 217 COM2

38 COM55 98 SEG106 158 SEG46 218 COM4

39 COM53 99 SEG105 159 SEG45 219 COM6

40 COM51 100 SEG104 160 SEG44 220 COM8

41 COM49 101 SEG103 161 SEG43 221 COM10

42 COM47 102 SEG102 162 SEG42 222 COM12

43 COM45 103 SEG101 163 SEG41 223 COM14

44 COM43 104 SEG100 164 SEG40 224 COM16

45 COM41 105 SEG99 165 SEG39 225 COM18

46 COM39 106 SEG98 166 SEG38 226 COM20

47 COM37 107 SEG97 167 SEG37 227 COM22

48 COM35 108 SEG96 168 SEG36 228 COM24

49 COM33 109 SEG95 169 SEG35 229 COM26

50 COM31 110 SEG94 170 SEG34 230 COM28

51 COM29 111 SEG93 171 SEG33 231 COM30

52 COM27 112 SEG92 172 SEG32 232 COM32

53 COM25 113 SEG91 173 SEG31 233 COM34

54 COM23 114 SEG90 174 SEG30 234 COM36

55 COM21 115 SEG89 175 SEG29 235 COM38

56 COM19 116 SEG88 176 SEG28 236 COM40

57 COM17 117 SEG87 177 SEG27 237 COM42

58 COM15 118 SEG86 178 SEG26 238 COM44

59 COM13 119 SEG85 179 SEG25 239 COM46

60 COM11 120 SEG84 180 SEG24 240 COM48

SSD1303 Rev 1.7 P 45/56 May 2005 S o l o m on S ystech

SSD1303T6R1 TAB Package Dimensions

SSD1303T6

Solomon S ystech May 2005 P 46/56 Rev 1.7 SSD1303

SSD1303 Rev 1.7 P 47/56 May 2005 S o l o m on S ystech

16 SSD1303T8R1 PACKAGE DETAILS

SSD1303T8R1 Pin Assignment

Remark:

Use internal clock

VREF is connected to VCC

Support MCU interface: 8-bit 6800/8080 parallel interface and SPI

VSSB, BGGND are connected to VSS

BS0 is connected to VSS

Solomon S ystech May 2005 P 48/56 Rev 1.7 SSD1303

Table 15 - SSD1303T8R1 pin assignment

P in no. Pi n nam e P i n no. Pin name P i n no. Pi n nam e Pi n no. Pi n nam e

1 NC 61 COM8 121 SEG47 181 COM7

2 VSS 62 COM6 122 SEG48 182 COM9

3 GDR 63 COM4 123 SEG49 183 COM11

4 VDDB 64 COM2 124 SEG50 184 COM13

5 FB 65 COM0 125 SEG51 185 COM15

6 RESE 66 NC 126 SEG52 186 COM17

7 VBREF 67 NC 127 SEG53 187 COM19

8 GP0 68 NC 128 SEG54 188 COM21

9 GP1 69 NC 129 SEG55 189 COM23

10 NC 70 NC 130 SEG56 190 COM25

11 VDD1 71 NC 131 SEG57 191 COM27

12 BS1 72 NC 132 SEG58 192 COM29

13 BS2 73 NC 133 SEG59 193 COM31

14 NC 74 SEG0 134 SEG60 194 COM33

15 CS# 75 SEG1 135 SEG61 195 COM35

16 RES# 76 SEG2 136 SEG62 196 COM37

17 D/C 77 SEG3 137 SEG63 197 COM39

18 R/W 78 SEG4 138 SEG64 198 COM41

19 E/RD 79 SEG5 139 SEG65 199 COM43

20 D0 80 SEG6 140 SEG66 200 COM45

21 D1 81 SEG7 141 SEG67 201 COM47

22 D2 82 SEG8 142 SEG68 202 COM49

23 D3 83 SEG9 143 SEG69 203 COM51

24 D4 84 SEG10 144 SEG70 204 COM53

25 D5 85 SEG11 145 SEG71 205 COM55

26 D6 86 SEG12 146 SEG72 206 COM57

27 D7 87 SEG13 147 SEG73 207 COM59

28 IREF 88 SEG14 148 SEG74 208 COM61

29 VCOMH 89 SEG15 149 SEG75 209 COM63

30 VCC 90 SEG16 150 SEG76 210 NC

31 NC 91 SEG17 151 SEG77 211 NC

32 NC 92 SEG18 152 SEG78

33 NC 93 SEG19 153 SEG79

34 COM62 94 SEG20 154 SEG80

35 COM60 95 SEG21 155 SEG81

36 COM58 96 SEG22 156 SEG82

37 COM56 97 SEG23 157 SEG83

38 COM54 98 SEG24 158 SEG84

39 COM52 99 SEG25 159 SEG85

40 COM50 100 SEG26 160 SEG86

41 COM48 101 SEG27 161 SEG87

42 COM46 102 SEG28 162 SEG88

43 COM44 103 SEG29 163 SEG89

44 COM42 104 SEG30 164 SEG90

45 COM40 105 SEG31 165 SEG91

46 COM38 106 SEG32 166 SEG92

47 COM36 107 SEG33 167 SEG93

48 COM34 108 SEG34 168 SEG94

49 COM32 109 SEG35 169 SEG95

50 COM30 110 SEG36 170 NC

51 COM28 111 SEG37 171 NC

52 COM26 112 SEG38 172 NC

53 COM24 113 SEG39 173 NC

54 COM22 114 SEG40 174 NC

55 COM20 115 SEG41 175 NC

56 COM18 116 SEG42 176 NC

57 COM16 117 SEG43 177 NC

58 COM14 118 SEG44 178 COM1

59 COM12 119 SEG45 179 COM3

60 COM10 120 SEG46 180 COM5

SSD1303 Rev 1.7 P 49/56 May 2005 S o l o m on S ystech

SSD1303T8R1 TAB Package Dimensions

Solomon S ystech May 2005 P 50/56 Rev 1.7 SSD1303

SSD1303 Rev 1.7 P 51/56 May 2005 S o l o m on S ystech

17 SSD1303T9R1 PACKAGE DETAILS

SSD1303T9R1 Pin Assignment

Figure 16 - SSD1303T9R1 pin assignment (Copper view)

Remark:

Use internal clock

VREF is connected to VCC

Support MCU interface: 8-bit 6800/8080 parallel interface and SPI

VSSB, BGGND are connected to VSS

BS0 is connected to VSS

Solomon S ystech May 2005 P 52/56 Rev 1.7 SSD1303

Table 16 - SSD1303T9R1 pin assignment

No. Pin

name Pin

No. Pin

name Pin

No. Pin

name Pin

No. Pin

name

1 NC 61 COM9 121 SEG80 181 COM6

2 VCC 62 COM7 122 SEG79 182 COM8

3 VCOMH 63 COM5 123 SEG78 183 COM10

4 IREF 64 COM3 124 SEG77 184 COM12

5 D7 65 COM1 125 SEG76 185 COM14

6 D6 66 NC 126 SEG75 186 COM16

7 D5 67 NC 127 SEG74 187 COM18

8 D4 68 NC 128 SEG73 188 COM20

9 D3 69 NC 129 SEG72 189 COM22

10 D2 70 NC 130 SEG71 190 COM24

11 D1 71 NC 131 SEG70 191 COM26

12 D0 72 NC 132 SEG69 192 COM28

13 E 73 NC 133 SEG68 193 COM30

14 R/W 74 SEG127 134 SEG67 194 COM32

15 D/C 75 SEG126 135 SEG66 195 COM34

16 RES 76 SEG125 136 SEG65 196 COM36

17 CS# 77 SEG124 137 SEG64 197 COM38

18 NC 78 SEG123 138 SEG63 198 COM40

19 BS2 79 SEG122 139 SEG62 199 COM42

20 BS1 80 SEG121 140 SEG61 200 COM44

21 VDD1 81 SEG120 141 SEG60 201 COM46

22 NC 82 SEG119 142 SEG59 202 COM48

23 GPIO1 83 SEG118 143 SEG58 203 COM50

24 GPIO0 84 SEG117 144 SEG57 204 COM52

25 VBREF 85 SEG116 145 SEG56 205 COM54

26 RESE 86 SEG115 146 SEG55 206 COM56

27 FB 87 SEG114 147 SEG54 207 COM58

28 VDDB 88 SEG113 148 SEG53 208 COM60

29 GDR 89 SEG112 149 SEG52 209 COM62

30 VSS 90 SEG111 150 SEG51 210 NC

31 NC 91 SEG110 151 SEG50 211 NC

32 NC 92 SEG109 152 SEG49

33 NC 93 SEG108 153 SEG48

34 COM63 94 SEG107 154 SEG47

35 COM61 95 SEG106 155 SEG46

36 COM59 96 SEG105 156 SEG45

37 COM57 97 SEG104 157 SEG44

38 COM55 98 SEG103 158 SEG43

39 COM53 99 SEG102 159 SEG42

40 COM51 100 SEG101 160 SEG41

41 COM49 101 SEG100 161 SEG40

42 COM47 102 SEG99 162 SEG39

43 COM45 103 SEG98 163 SEG38

44 COM43 104 SEG97 164 SEG37

45 COM41 105 SEG96 165 SEG36

46 COM39 106 SEG95 166 SEG35

47 COM37 107 SEG94 167 SEG34

48 COM35 108 SEG93 168 SEG33

49 COM33 109 SEG92 169 SEG32

50 COM31 110 SEG91 170 NC

51 COM29 111 SEG90 171 NC

52 COM27 112 SEG89 172 NC

53 COM25 113 SEG88 173 NC

54 COM23 114 SEG87 174 NC

55 COM21 115 SEG86 175 NC

56 COM19 116 SEG85 176 NC

57 COM17 117 SEG84 177 NC

58 COM15 118 SEG83 178 COM0

59 COM13 119 SEG82 179 COM2

60 COM11 120 SEG81 180 COM4

SSD1303 Rev 1.7 P 53/56 May 2005 S o l o m on S ystech

SSD1303T9R1 TAB Package Dimensions

SSD1303T9

Solomon S ystech May 2005 P 54/56 Rev 1.7 SSD1303

SSD1303 Rev 1.7 P 55/56 May 2005 S o l o m on S ystech

18 SSD1303Z PACKAGE DETAILS

DIE TRAY DIMENSIONS

Solomon S ystech May 2005 P 56/56 Rev 1.7 SSD1303

http://www.solomon-systech.com

Solomon Systech reserves the right to make changes without further notice to any products herein. Solomon Systech makes no warranty,

representation or guarantee regarding the suitability of its products for any particular purpose, nor does Solomon Systech assum e any liability arising

out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential o

incidental damages. “Typical” parameters can and do vary in different applications. All operating parameters, including “Typicals” must be validated

for each custom er applicati on by customer’s techni cal experts. Solomon Systech does not convey any license under its patent rig hts nor the rights o

others. Solomon S ystech products are not designed, intended, or authorized for use as components in system s intended for surgical im plant into the

body, or other applications intended to support or sustain life, or for any other application in which the failure of the Solom on Systech product could

create a situation where personal injury or death may occur. Should Buyer purchase or use Solomon Systech products for any such unintended o

unauthorized application, Buyer shall indemnify and hold Solomon Systech and its offices, employees, subsidiaries, affiliates, and distributors

harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal

injury or death associated with such unintended or unauthorized use, even if such claim alleges that Solomon Systech was negligent regarding the

design or manufacture of the part.