DS99R105, DS99R106
www.ti.com
SNLS242D –MARCH 2007–REVISED APRIL 2013
DS99R105/DS99R106 3-40MHz DC-Balanced 24-Bit LVDS Serializer and Deserializer
Check for Samples: DS99R105,DS99R106
1FEATURES DESCRIPTION
The DS99R105/DS99R106 Chipset translates a 24-
2• 3 MHz–40 MHz Clock Embedded and DC- bit parallel bus into a fully transparent data/control
Balancing 24:1 and 1:24 Data Transmissions LVDS serial stream with embedded clock information.
• Capable to Drive Shielded Twisted-Pair Cable This single serial stream simplifies transferring a 24-
• User Selectable Clock Edge for Parallel Data bit bus over PCB traces and cable by eliminating the
skew problems between parallel data and clock
on Both Transmitter and Receiver paths. It saves system cost by narrowing data paths
• Internal DC Balancing Encode/Decode – that in turn reduce PCB layers, cable width, and
Supports AC-Coupling Interface with no connector size and pins.
External Coding Required The DS99R105/DS99R106 incorporates LVDS
• Individual Power-Down Controls for Both signaling on the high-speed I/O. LVDS provides a low
Transmitter and Receiver power and low noise environment for reliably
• Embedded Clock CDR (Clock and Data transferring data over a serial transmission path. By
Recovery) on Receiver and no External Source optimizing the serializer output edge rate for the
of Reference Clock Needed operating frequency range EMI is further reduced.
• All Codes RDL (Random Data Lock) to Support In addition the device features pre-emphasis to boost
Live-Pluggable Applications signals over longer distances using lossy cables.
Internal DC balanced encoding/decoding is used to
• LOCK Output Flag to Ensure Data Integrity at support AC-Coupled interconnects.
Receiver Side
• Balanced TSETUP/THOLD between RCLK and
RDATA on Receiver Side
• PTO (Progressive Turn-On) LVCMOS Outputs
to Reduce EMI and Minimize SSO Effects
• All LVCMOS Inputs and Control Pins have
Internal Pulldown
• On-Chip Filters for PLLs on Transmitter and
Receiver
• Integrated 100ΩInput Termination on Receiver
• 4 mA Receiver Output Drive
• 48-Pin TQFP and 48-Pin WQFN Packages
• Pure CMOS .35 μm Process
• Power Supply Range 3.3V ± 10%
• Temperature Range 0°C to +70°C
• 8 kV HBM ESD Tolerance
1Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date. Copyright © 2007–2013, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
DEN
VODSEL
DIN
TRFB
24
REN
RRFB
RPWDNB
TCLK
TPWDNB
SERIALIZER ± DS99R105
PLL
Timing
and
Control
DOUT-
RT = 100:
RT = 100:
(Integrated)
RIN-
DESERIALIZER ± DS99R106
DOUT+ RIN+
PLL Timing
and
Control
24 ROUT
LOCK
RCLK
Clock
Recovery
Output Latch
Serial to Parallel
DC Balance Decode
Input Latch
Parallel to Serial
DC Balance Encode
CLK1
bit0
bit1
bit2
bit3
bit4
bit5
bit6
bit7
bit8
bit9
bit10
bit11
DCA
DCB
bit12
bit13
bit14
bit15
bit16
bit17
bit18
bit19
bit20
bit21
bit22
bit23
CLK0
PRE (on/off)
DS99R105, DS99R106
SNLS242D –MARCH 2007–REVISED APRIL 2013
www.ti.com
Block Diagram
Figure 1.
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
2Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: DS99R105 DS99R106
DS99R105, DS99R106
www.ti.com
SNLS242D –MARCH 2007–REVISED APRIL 2013
Absolute Maximum Ratings (1)(2)
Supply Voltage (VDD)−0.3V to +4V
LVCMOS/LVTTL Input Voltage −0.3V to (VDD +0.3V)
LVCMOS/LVTTL Output Voltage −0.3V to (VDD +0.3V)
LVDS Receiver Input Voltage −0.3V to 3.9V
LVDS Driver Output Voltage −0.3V to 3.9V
LVDS Output Short Circuit Duration 10 ms
Junction Temperature +150°C
Storage Temperature −65°C to +150°C
Lead Temperature
(Soldering, 4 seconds) +260°C
Maximum Package Power Dissipation Capacity Package
De-rating:
48L TQFP 1/θJA °C/W above +25°C
DS99R105
θJA 45.8 (4L*); 75.4 (2L*) °C/W
θJC 21.0°C/W
DS99R106
θJA 45.4 (4L*); 75.0 (2L*)°C/W
θJC 21.1°C/W
48L WQFN 1/θJA °C/W above +25°C
DS99R105
θJA 28 (4L*); 79.1 (2L*) °C/W
θJC 3.7°C/W
DS99R106
θJA 28 (4L*); 79.1 (2L*)°C/W
θJC 3.71°C/W
*JEDEC
ESD Rating (HBM) ≥±8 kV
(1) “Absolute Maximum Ratings” indicate limits beyond which damage to the device may occur, including inoperability and degradation of
device reliability and/or performance. Functional operation of the device and/or non-degradation at the Absolute Maximum Ratings or
other conditions beyond those indicated in the Recommended Operating Conditions is not implied. The Recommended Operating
Conditions indicate conditions at which the device is functional and the device should not be operated beyond such conditions.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and
specifications.
Recommended Operating Conditions Min Nom Max Units
Supply Voltage (VDD) 3.0 3.3 3.6 V
Operating Free Air
Temperature (TA) 0 +25 +70 °C
Clock Rate 3 40 MHz
Supply Noise ±100 mVP-P
Copyright © 2007–2013, Texas Instruments Incorporated Submit Documentation Feedback 3
Product Folder Links: DS99R105 DS99R106
DS99R105, DS99R106
SNLS242D –MARCH 2007–REVISED APRIL 2013
www.ti.com
Electrical Characteristics(1)(2)(3)
Over recommended operating supply and temperature ranges unless otherwise specified.
Parameter Test Conditions Pin/Freq. Min Typ Max Units
LVCMOS/LVTTL DC SPECIFICATIONS
VIH High Level Voltage Tx: DIN[23:0], TCLK, 2.0 1.5 VDD V
TPWDNB, DEN, TRFB,
VIL Low Level Input Voltage GND 1.5 0.8 V
DCAOFF, DCBOFF,
VCL Input Clamp Voltage ICL =−18 mA VODSEL
(4) −0.8 −1.5 V
Rx: RPWDNB, RRFB,
REN
IIN Input Current VIN = 0V or 3.6V Tx: DIN[23:0], TCLK,
TPWDNB, DEN, TRFB, −10 ±1 +10 µA
DCAOFF, DCBOFF,
VODSEL
Rx: RPWDNB, RRFB, −20 ±5 +20 µA
REN
VOH High Level Output Voltage IOH =−4 mA Rx: ROUT[23:0], RCLK, 2.3 3.0 VDD V
LOCK
VOL Low Level Output Voltage IOL = +4 mA GND 0.33 0.5 V
IOS Output Short Circuit Current VOUT = 0V −40 −70 −110 mA
(4)
IOZ TRI-STATE Output Current RPWDNB, REN = 0V Rx: ROUT[23:0], RCLK, −30 ±0.4 +30 µA
VOUT = 0V or 2.4V LOCK
LVDS DC SPECIFICATIONS
VTH Differential Threshold High VCM = +1.2V Rx: RIN+, RIN−+50 mV
Voltage
VTL Differential Threshold Low −50 mV
Voltage
IIN Input Current VIN = +2.4V, ±300 µA
VDD = 3.6V
VIN = 0V, VDD = 3.6V ±300 µA
RTDifferential Internal 90 100 130 Ω
Termination Resistance
VOD Output Differential Voltage RL= 100Ω, w/o Pre-emphasis Tx: DOUT+, DOUT−250 400 600 mV
(DOUT+)–(DOUT−) VODSEL = L (Figure 11)
RL= 100Ω, w/o Pre-emphasis 450 750 1200 mV
VODSEL = H (Figure 11)
ΔVOD Output Differential Voltage RL= 100Ω, w/o Pre-emphasis 4 50 mV
Unbalance
VOS Offset Voltage RL= 100Ω, w/o Pre-emphasis 1.00 1.25 1.50 V
ΔVOS Offset Voltage Unbalance RL= 100Ω, w/o Pre-emphasis 1 50 mV
IOS Output Short Circuit Current DOUT = 0V, DIN = H,
TPWDNB, DEN = 2.4V, −2−5−8 mA
VODSEL = L
DOUT = 0V, DIN = H,
TPWDNB, DEN = 2.4V, −7−10 −13 mA
VODSEL = H
IOZ TRI-STATE Output Current TPWDNB, DEN = 0V, −15 ±1 +15 µA
DOUT = 0V or 2.4V
(1) The Electrical Characteristics tables list ensured specifications under the listed Recommended Operating Conditions except as
otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only and
are not ensured.
(2) Typical values represent most likely parametric norms at VDD = 3.3V, Ta = +25 degC, and at the Recommended Operation Conditions
at the time of product characterization and are not ensured.
(3) Current into device pins is defined as positive. Current out of a device pin is defined as negative. Voltages are referenced to ground
except VOD, ΔVOD, VTH and VTL which are differential voltages.
(4) Specification is ensured by characterization and is not tested in production.
4Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: DS99R105 DS99R106
DS99R105, DS99R106
www.ti.com
SNLS242D –MARCH 2007–REVISED APRIL 2013
Electrical Characteristics(1)(2)(3) (continued)
Over recommended operating supply and temperature ranges unless otherwise specified.
Parameter Test Conditions Pin/Freq. Min Typ Max Units
SER/DES SUPPLY CURRENT (DVDD*, PVDD* and AVDD* pins) *Digital, PLL, and Analog VDDs
IDDT Serializer (Tx) RL= 100Ωf = 40 MHz
Total Supply Current Pre-emphasis = OFF 40 80 mA
(includes load current) VODSEL = L
Checker-board pattern (Figure 2)
RL= 100Ωf = 40 MHz
Pre-emphasis = ON 45 85 mA
VODSEL = L
Checker-board pattern (Figure 2)
Serializer (Tx) RL= 100Ωf = 40 MHz
Total Supply Current Pre-emphasis = OFF 40 85 mA
(includes load current) VODSEL = H
Checker-board pattern (Figure 2)
RL= 100Ωf = 40 MHz
Pre-emphasis = ON 45 90 mA
VODSEL = H
Checker-board pattern (Figure 2)
IDDTZ Serializer (Tx) TPWDNB = 0V 1 100 µA
Supply Current Power-down (All other LVCMOS Inputs = 0V)
IDDR Deserializer (Rx) CL= 8 pF LVCMOS Output f = 40 MHz
Total Supply Current Checker-board pattern 95 mA
(includes load current) (Figure 3)
Deserializer (Rx) CL= 8 pF LVCMOS Output f = 40 MHz
Total Supply Current Random pattern 90 mA
(includes load current)
IDDRZ Deserializer (Rx) RPWDNB = 0V
Supply Current Power-down (All other LVCMOS Inputs = 0V, 1 50 µA
RIN+/ RIN-= 0V)
Serializer Timing Requirements for TCLK(1)(2)
Over recommended operating supply and temperature ranges unless otherwise specified.
Parameter Test Conditions Min Typ Max Units
tTCP Transmit Clock Period (Figure 6)25 T 333 ns
tTCIH Transmit Clock High Time 0.4T 0.5T 0.6T ns
tTCIL Transmit Clock Low Time 0.4T 0.5T 0.6T ns
tCLKT TCLK Input Transition Time (Figure 5)3 6 ns
tJIT TCLK Input Jitter (3) 33 ps (RMS)
(1) Figure 2,Figure 3,Figure 9,Figure 13, and Figure 15 show a falling edge data strobe (TCLK IN/RCLK OUT).
(2) Figure 6 and Figure 16 show a rising edge data strobe (TCLK IN/RCLK OUT).
(3) tJIT (@BER of 10e-9) specifies the allowable jitter on TCLK. tJIT not included in TxOUT_E_O parameter.
Serializer Switching Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified.
Parameter Test Conditions Min Typ Max Units
tLLHT LVDS Low-to-High Transition Time RL= 100Ω,(Figure 4)0.6 ns
CL= 10 pF to GND
tLHLT LVDS High-to-Low Transition Time 0.6 ns
VODSEL = L
tDIS DIN (23:0) Setup to TCLK RL= 100Ω, 5 ns
CL= 10 pF to GND
tDIH DIN (23:0) Hold from TCLK 5 ns
(1)
(1) Specification is ensured by characterization and is not tested in production.
Copyright © 2007–2013, Texas Instruments Incorporated Submit Documentation Feedback 5
Product Folder Links: DS99R105 DS99R106
DS99R105, DS99R106
SNLS242D –MARCH 2007–REVISED APRIL 2013
www.ti.com
Serializer Switching Characteristics (continued)
Over recommended operating supply and temperature ranges unless otherwise specified.
Parameter Test Conditions Min Typ Max Units
tHZD DOUT ± HIGH to TRI-STATE Delay RL= 100Ω, 15 ns
CL= 10 pF to GND
tLZD DOUT ± LOW to TRI-STATE Delay 15 ns
(Figure 7)(2)
tZHD DOUT ± TRI-STATE to HIGH Delay 200 ns
tZLD DOUT ± TRI-STATE to LOW Delay 200 ns
tPLD Serializer PLL Lock Time RL= 100Ω,(Figure 8)10 ms
tSD Serializer Delay RL= 100Ω,(Figure 9)3.5T + 3.5T + ns
VODSEL = L, TRFB = H 2.85 10
RL= 100Ω,(Figure 9)3.5T + 3.5T + ns
VODSEL = L, TRFB = L 2.85 10
TxOUT_E_O TxOUT_Eye_Opening 3–40 MHz UI
0.68
(respect to ideal) (Figure 10)(3) (4) (5)
(2) When the Serializer output is tri-stated, the Deserializer will lose PLL lock. Resynchronization MUST occur before data transfer.
(3) tJIT (@BER of 10e-9) specifies the allowable jitter on TCLK. tJIT not included in TxOUT_E_O parameter.
(4) TxOUT_E_O is affected by pre-emphasis value.
(5) UI – Unit Interval, equivalent to one ideal serialized data bit width. The UI scales with frequency.
Deserializer Switching Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified.
Parameter Test Conditions Pin/Freq. Min Typ Max Units
tRCP Receiver out Clock Period tRCP = tTCP (1) RCLK 25 T 333 ns
tRDC RCLK Duty Cycle RCLK 45 50 55 %
tCLH LVCMOS Low-to-High CL= 8 pF ROUT [23:0], 2.5 3.5 ns
Transition Time (lumped load) LOCK, RCLK
(Figure 12)
tCHL LVCMOS High-to-Low 2.5 3.5 ns
Transition Time
tROS ROUT (7:0) Setup Data to RCLK (Figure 16)ROUT [7:0] (0.40)* (29/56)*tRCP ns
(Group 1) tRCP
tROH ROUT (7:0) Hold Data to RCLK (0.40)* (27/56)*tRCP ns
(Group 1) tRCP
tROS ROUT (15:8) Setup Data to RCLK (Figure 16)ROUT [15:8], (0.40)* 0.5*tRCP ns
(Group 2) LOCK tRCP
tROH ROUT (15:8) Hold Data to RCLK (0.40)* 0.5*tRCP ns
(Group 2) tRCP
tROS ROUT (23:16) Setup Data to (Figure 16)ROUT [23:16] (0.40)* (27/56)*tRCP ns
RCLK (Group 3) tRCP
tROH ROUT (23:16) Hold Data to RCLK (0.40)* (29/56)*tRCP ns
(Group 3) tRCP
tHZR HIGH to TRI-STATE Delay (Figure 14)ROUT [23:0], 3 10 ns
RCLK, LOCK
tLZR LOW to TRI-STATE Delay 3 10 ns
tZHR TRI-STATE to HIGH Delay 3 10 ns
tZLR TRI-STATE to LOW Delay 3 10 ns
tDD Deserializer Delay (Figure 13)RCLK [4+(3/56)]T [4+(3/56)]T ns
+5.9 +18.5
tDRDL Deserializer PLL Lock Time from (Figure 15)3 MHz 5 50 ms
Powerdown (2) (1) 40 MHz 5 50 ms
RxIN_TOL_L Receiver INput TOLerance Left (Figure 17)(3) (1) (4) 3 MHz–40 MHz 0.25 UI
RxIN_TOL_R Receiver INput TOLerance Right (Figure 17)(3) (1) (4) 3 MHz–40 MHz 0.25 UI
(1) Specification is ensured by characterization and is not tested in production.
(2) The Deserializer PLL lock time (tDRDL) may vary depending on input data patterns and the number of transitions within the pattern.
(3) RxIN_TOL is a measure of how much phase noise (jitter) the deserializer can tolerate in the incoming data stream before bit errors
occur. It is a measurement in reference with the ideal bit position, please see TI’s AN-1217 (SNLA053) for detail.
(4) UI – Unit Interval, equivalent to one ideal serialized data bit width. The UI scales with frequency.
6Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: DS99R105 DS99R106
80%
20%
80%
20%
tCLKT tCLK
TCLK
VDD
0V
80%
20%
80%
20% Vdiff = 0V
tLLHT tLHLT
Differential
Signal
Vdiff = (DOUT+) - (DOUT-)
100:
DOUT+
DOUT- 10 pF
10 pF
RCLK
ODD ROUT
EVEN ROUT
Signal PatternDevice Pin Name
TCLK
ODD DIN
EVEN DIN
Signal PatternDevice Pin Name
DS99R105, DS99R106
www.ti.com
SNLS242D –MARCH 2007–REVISED APRIL 2013
AC Timing Diagrams and Test Circuits
See Serializer Timing Requirements for TCLK Note (1).
Figure 2. Serializer Input Checker-board Pattern
See Serializer Timing Requirements for TCLK Note (1).
Figure 3. Deserializer Output Checker-board Pattern
Figure 4. Serializer LVDS Output Load and Transition Times
Figure 5. Serializer Input Clock Transition Times
Copyright © 2007–2013, Texas Instruments Incorporated Submit Documentation Feedback 7
Product Folder Links: DS99R105 DS99R106
DEN
DOUT-
DOUT+ 5 pF 100:
Parasitic package and
Trace capcitance
200 mV DCA DCA DCA DCA $OOGDWD³0´V
CLK1
tZLD
tTCP
DCADCADCADCA
CLK1
tTCP
200 mV
DEN
(single-ended)
200 mV DCA DCA DCA DCA $OOGDWD³1´V
CLK0
tZHD
tTCP
DCADCA
DCA
DCA
CLK0
tTCP
200 mV
DOUT±
(differential)
VCC/2
0V
DOUT±
(differential)
0V
VCC/2
tHZD
DEN
(single-ended)
VCC/2
0V 0V
VCC/2
tLZD
Setup
VDD/2 Hold
tDIH
tDIS
TCLK
DIN [0:23]
tTCP
0V
VDD/2
VDD/2 VDD/2VDD/2
VDD
DS99R105, DS99R106
SNLS242D –MARCH 2007–REVISED APRIL 2013
www.ti.com
See Serializer Timing Requirements for TCLK Note (2).
Figure 6. Serializer Setup/Hold Times
Figure 7. Serializer TRI-STATE Test Circuit and Delay
8Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: DS99R105 DS99R106
PARALLEL-TO-SERIAL
DOUT+
DOUT-
24
DIN RL
TCLK
Ideal Center Position (tBIT/2)
tBIT (1UI)
TxOUT_E_O
Ideal Data Bit
End
Ideal Data Bit
Beginning
tBIT(1/2UI) tBIT(1/2UI)
2.0V 0.8V
TCLK
DOUT±
tHZD or
tLZD
tZHD or
tZLD
Output
Active
tPLD
PWDWN
TRI-STATE TRI-STATE
DS99R105, DS99R106
www.ti.com
SNLS242D –MARCH 2007–REVISED APRIL 2013
Figure 8. Serializer PLL Lock Time, and TPWDNB TRI-STATE Delays
See Serializer Timing Requirements for TCLK Note (1).
Figure 9. Serializer Delay
Figure 10. Transmitter Output Eye Opening (TxOUT_E_O)
VOD = (DOUT+) – (DOUT -)
Differential output signal is shown as (DOUT+) – (DOUT -), device in Data Transfer mode.
Figure 11. Serializer VOD Diagram
Copyright © 2007–2013, Texas Instruments Incorporated Submit Documentation Feedback 9
Product Folder Links: DS99R105 DS99R106
VOH
REN
VOL + 0.5V
VOL
ROUT [23:0]
VOL + 0.5V
tLZR
500:
VREF = VDD/2 for tZLR or tLZR,
VOH - 0.5V VOH + 0.5V
tZLR
tHZR tZHR
VDD/2 VDD/2
VOH
VOL
REN
VREF +
-VREF = 0V for tZHR or tHZR
CL = 8pF
23210
||
START
BIT
STOP
BIT
SYMBOL N+3
23210
||
START
BIT
STOP
BIT
SYMBOL N+2
23210
||
START
BIT
STOP
BIT
SYMBOL N+1
23210
||
START
BIT
STOP
BIT
SYMBOL N
RIN0-23
DCA, DCB
RCLK
tDD
ROUT0-23 SYMBOL N-1 SYMBOL NSYMBOL N-2SYMBOL N-3
80%
20%
80%
20%
tCLH
Deserializer 8 pF
lumped
Single-ended
Signal
tCHL
DS99R105, DS99R106
SNLS242D –MARCH 2007–REVISED APRIL 2013
www.ti.com
Figure 12. Deserializer LVCMOS/LVTTL Output Load and Transition Times
See Serializer Timing Requirements for TCLK Note (1).
Figure 13. Deserializer Delay
Note: CLincludes instrumentation and fixture capacitance within 6 cm of ROUT[23:0]
Figure 14. Deserializer TRI-STATE Test Circuit and Timing
10 Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: DS99R105 DS99R106
Data Valid
Before RCLK
Data Valid
After RCLK
ROUT [7:0]
Data Valid
Before RCLK
Data Valid
After RCLK
ROUT [15:8], LOCK
Data Valid
Before RCLK
Data Valid
After RCLK VDD/2
ROUT [23:16]
RCLK tLOW tHIGH
tROS tROH
tROS tROH
(group 1) (group 1)
(group 2) (group 2)
1/2 UI 1/2 UI
tROS tROH
(group 3) (group 3)
1/2 UI 1/2 UI
VDD/2
VDD/2VDD/2
VDD/2VDD/2
VDD/2VDD/2
RIN±
||
TRI-STATE
TRI-STATE
TRI-STATE
TRI-STATE
TRI-STATE
ROUT [0:23]
RCLK
TRI-STATE
LOCK
}v[šŒ
tHZR or tLZR
tDRDL
REN
PWDN
2.0V
0.8V
DS99R105, DS99R106
www.ti.com
SNLS242D –MARCH 2007–REVISED APRIL 2013
See Serializer Timing Requirements for TCLK Note (1).
Figure 15. Deserializer PLL Lock Times and RPWDNB TRI-STATE Delay
See Serializer Timing Requirements for TCLK Note (2).
Figure 16. Deserializer Setup and Hold Times
Copyright © 2007–2013, Texas Instruments Incorporated Submit Documentation Feedback 11
Product Folder Links: DS99R105 DS99R106
48DIN[19]
47DIN[18]
46DIN[17]
45DIN[16]
44DIN[15]
43
VSSIT
42
VDDIT
41DIN[14]
40DIN[13]
39DIN[12]
38DIN[11]
37DIN[10]
13
14
15
16
17
18
19
20
21
22
23
24
RESRVD
VDDPT1
VSSPT1
VDDPT0
VSSPT0
DEN
DOUT-
DOUT+
VSSDR
VDDDR
PRE
VSS
12
VODSEL
11
TRFB
10
TCLK
9
TPWDNB
8
DCBOFF
7
VDDL
6
VSSL
5
DCAOFF
4
DIN[23]
3
DIN[22]
2
DIN[21]
1
DIN[20]
25
26
27
28
29
30
31
32
33
34
35
36
DIN[0]
DIN[1]
DIN[2]
DIN[3]
DIN[4]
VDDT
VSST
DIN[5]
DIN[6]
DIN[7]
DIN[8]
DIN[9]
DS99R105
48 PIN WQFN
48 PIN TQFP
Ideal Sampling Position
tBIT
(1UI)
Sampling
Window Ideal Data Bit
End
Ideal Data Bit
Beginning
RxIN_TOL -L
2
tBIT
( )
RxIN_TOL -R
DS99R105, DS99R106
SNLS242D –MARCH 2007–REVISED APRIL 2013
www.ti.com
RxIN_TOL_L is the ideal noise margin on the left of the figure, with respect to ideal.
RxIN_TOL_R is the ideal noise margin on the right of the figure, with respect to ideal.
TxOUT_E_O is affected by pre-emphasis value.
Figure 17. Receiver Input Tolerance (RxIN_TOL) and Sampling Window
DS99R105 Pin Diagram
Top View
Figure 18. Serializer - DS99R105
See Package Numbers NJU0048D and PFB0048A
12 Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: DS99R105 DS99R106
DS99R105, DS99R106
www.ti.com
SNLS242D –MARCH 2007–REVISED APRIL 2013
DS99R105 Serializer Pin Descriptions
Pin Pin Name I/O Description
No.
LVCMOS PARALLEL INTERFACE PINS
4-1, DIN[23:0] LVCMOS_I Transmitter Parallel Interface Data Inputs Pins. Tie LOW if unused, do not float.
48-44,
41-32,
29-25
10 TCLK LVCMOS_I Transmitter Parallel Interface Clock Input Pin. Strobe edge set by TRFB configuration pin.
CONTROL AND CONFIGURATION PINS
9 TPWDNB LVCMOS_I Transmitter Power Down Bar
TPWDNB = H; Transmitter is Enabled and ON
TPWDNB = L; Transmitter is in power down mode (Sleep), LVDS Driver DOUT (+/-) Outputs are
in TRI-STATE stand-by mode, PLL is shutdown to minimize power consumption.
18 DEN LVCMOS_I Transmitter Data Enable
DEN = H; LVDS Driver Outputs are Enabled (ON).
DEN = L; LVDS Driver Outputs are Disabled (OFF), Transmitter LVDS Driver DOUT (+/-) Outputs
are in TRI-STATE, PLL still operational and locked to TCLK.
23 PRE LVCMOS_I PRE-emphasis select pin.
PRE = L; Pre-emphasis is enabled
PRE = H; Pre-emphasis is disabled
11 TRFB LVCMOS_I Transmitter Clock Edge Select Pin
TRFB = H; Parallel Interface Data is strobed on the Rising Clock Edge
TRFB = L; Parallel Interface Data is strobed on the Falling Clock Edge
12 VODSEL LVCMOS_I VOD Level Select
VODSEL = L; LVDS Driver Output is ±400 mV (RL= 100Ω)
VODSEL = H; LVDS Driver Output is ±750 mV (RL= 100Ω)
For normal applications, set this pin LOW. For long cable applications where a larger VOD is
required, set this pin HIGH.
5 DCAOFF LVCMOS_I RESERVED – This pin MUST be tied LOW.
8 DCBOFF LVCMOS_I RESERVED – This pin MUST be tied LOW.
13 RESRVD LVCMOS_I RESERVED – This pin MUST be tied LOW.
LVDS SERIAL INTERFACE PINS
20 DOUT+ LVDS_O Transmitter LVDS True (+) Output. This output is intended to be loaded with a 100 ohm load to
the DOUT+ pin. The interconnect should be AC Coupled to this pin with a 100 nF capacitor.
19 DOUT−LVDS_O Transmitter LVDS Inverted (-) Output This output is intended to be loaded with a 100 ohm load to
the DOUT- pin. The interconnect should be AC Coupled to this pin with a 100 nF capacitor.
POWER / GROUND PINS
22 VDDDR VDD Analog Voltage Supply, LVDS Output Power
21 VSSDR GND Analog Ground, LVDS Output Ground
16 VDDPT0 VDD Analog Voltage supply, VCO Power
17 VSSPT0 GND Analog Ground, VCO Ground
14 VDDPT1 VDD Analog Voltage supply, PLL Power
15 VSSPT1 GND Analog Ground, PLL Ground
30 VDDT VDD Digital Voltage supply, Tx Serializer Power
31 VSST GND Digital Ground, Tx Serializer Ground
7 VDDL VDD Digital Voltage supply, Tx Logic Power
6 VSSL GND Digital Ground, Tx Logic Ground
42 VDDIT VDD Digital Voltage supply, Tx Input Power
43 VSSIT GND Digital Ground, Tx Input Ground
24 VSS GND ESD Ground
Copyright © 2007–2013, Texas Instruments Incorporated Submit Documentation Feedback 13
Product Folder Links: DS99R105 DS99R106
48REN
47
VDDPR0
46
VSSPR0
45
VDDPR1
44
VSSPR1
43RRFB
42RIN-
41RIN+
40
VSSIR
39
VDDIR
38
VSSR1
37
VDDR1
13
14
15
16
17
18
19
20
21
22
23
24
ROUT[15]
ROUT[14]
ROUT[13]
ROUT[12]
LOCK
RCLK
VSSOR2
VDDOR2
ROUT[11]
ROUT[10]
ROUT[9]
ROUT[8]
12
ROUT[16]
11
ROUT[17]
10
ROUT[18]
9
ROUT[19]
8
VSSOR3
7
VDDOR3
6
ROUT[20]
5
ROUT[21]
4
ROUT[22]
3
ROUT[23]
2
RESRVD
1
RPWDNB
25
26
27
28
29
30
31
32
33
34
35
36
ROUT[7]
ROUT[6]
ROUT[5]
ROUT[4]
VSSOR1
VDDOR1
ROUT[3]
ROUT[2]
ROUT[1]
ROUT[0]
VSSR0
VDDR0
PTO GROUP 3
PTO GROUP 1
PTO GROUP 2
DS99R106
48 PIN WQFN
48 PIN TQFP
DS99R105, DS99R106
SNLS242D –MARCH 2007–REVISED APRIL 2013
www.ti.com
DS99R106 Pin Diagram
Top View
Figure 19. Deserializer - DS99R106
See Package Numbers NJU0048D and PFB0048A
DS99R106 Deserializer Pin Descriptions
Pin Pin Name I/O Description
No.
LVCMOS PARALLEL INTERFACE PINS
25-28, ROUT[7:0] LVCMOS_O Receiver Parallel Interface Data Outputs – Group 1
31-34
13-16, ROUT[15:8] LVCMOS_O Receiver Parallel Interface Data Outputs – Group 2
21-24
3-6, 9- ROUT[23:16] LVCMOS_O Receiver Parallel Interface Data Outputs – Group 3
12
18 RCLK LVCMOS_O Parallel Interface Clock Output Pin. Strobe edge set by RRFB configuration pin.
CONTROL AND CONFIGURATION PINS
43 RRFB LVCMOS_I Receiver Clock Edge Select Pin
RRFB = H; ROUT LVCMOS Outputs strobed on the Rising Clock Edge.
RRFB = L; ROUT LVCMOS Outputs strobed on the Falling Clock Edge.
48 REN LVCMOS_I Receiver Data Enable
REN = H; ROUT[23-0] and RCLK are Enabled (ON).
REN = L; ROUT[23-0] and RCLK are Disabled (OFF), Receiver ROUT[23-0] and RCLK Outputs
are in TRI-STATE, PLL still operational and locked to TCLK.
1 RPWDNB LVCMOS_I Receiver Data Enable
REN = H; ROUT[23-0] and RCLK are Enabled (ON).
REN = L; ROUT[23-0] and RCLK are Disabled (OFF), Receiver ROUT[23-0] and RCLK Outputs
are in TRI-STATE, PLL still operational and locked to TCLK.
14 Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: DS99R105 DS99R106
DS99R105, DS99R106
www.ti.com
SNLS242D –MARCH 2007–REVISED APRIL 2013
DS99R106 Deserializer Pin Descriptions (continued)
Pin Pin Name I/O Description
No.
17 LOCK LVCMOS_O LOCK indicates the status of the receiver PLL
LOCK = H; receiver PLL is locked
LOCK = L; receiver PLL is unlocked, ROUT[23-0] and RCLK are TRI-STATED
2 RESRVD LVCMOS_I RESERVED – This pin MUST be tied LOW.
LVDS SERIAL INTERFACE PINS
41 RIN+ LVDS_I Receiver LVDS True (+) Input This input is intended to be terminated with a 100 ohm load to the
RIN+ pin. The interconnect should be AC Coupled to this pin with a 100 nF capacitor.
42 RIN−LVDS_I Receiver LVDS Inverted (−) Input This input is intended to be terminated with a 100 ohm load to
the RIN- pin. The interconnect should be AC Coupled to this pin with a 100 nF capacitor.
POWER / GROUND PINS
39 VDDIR VDD Analog LVDS Voltage supply, Power
40 VSSIR GND Analog LVDS Ground
47 VDDPR0 VDD Analog Voltage supply, PLL Power
46 VSSPR0 GND Analog Ground, PLL Ground
45 VDDPR1 VDD Analog Voltage supply, PLL VCO Power
44 VSSPR1 GND Analog Ground, PLL VCO Ground
37 VDDR1 VDD Digital Voltage supply, Logic Power
38 VSSR1 GND Digital Ground, Logic Ground
36 VDDR0 VDD Digital Voltage supply, Logic Power
35 VSSR0 GND Digital Ground, Logic Ground
30 VDDOR1 VDD Digital Voltage supply, LVCMOS Output Power
29 VSSOR1 GND Digital Ground, LVCMOS Output Ground
20 VDDOR2 VDD Digital Voltage supply, LVCMOS Output Power
19 VSSOR2 GND Digital Ground, LVCMOS Output Ground
7 VDDOR3 VDD Digital Voltage supply, LVCMOS Output Power
8 VSSOR3 GND Digital Ground, LVCMOS Output Ground
Copyright © 2007–2013, Texas Instruments Incorporated Submit Documentation Feedback 15
Product Folder Links: DS99R105 DS99R106
DS99R105, DS99R106
SNLS242D –MARCH 2007–REVISED APRIL 2013
www.ti.com
FUNCTIONAL DESCRIPTION
The DS99R105 Serializer and DS99R106 Deserializer chipset is an easy-to-use transmitter and receiver pair that
sends 24-bits of parallel LVCMOS data over a single serial LVDS link from 72 Mbps to 960 Mbps throughput.
The DS99R105 transforms a 24-bit wide parallel LVCMOS data into a single high speed LVDS serial data stream
with embedded clock. The DS99R106 receives the LVDS serial data stream and converts it back into a 24-bit
wide parallel data and recovered clock. The 24-bit Serializer/Deserializer chipset is designed to transmit data
over shielded twisted pair (STP) at clock speeds from 3 MHz to 40 MHz.
The Deserializer can attain lock to a data stream without the use of a separate reference clock source. The
Deserializer synchronizes to the Serializer regardless of data pattern, delivering true automatic “plug and lock”
performance. The Deserializer recovers the clock and data by extracting the embedded clock information and
validating data integrity from the incoming data stream and then deserializes the data. The Deserializer monitors
the incoming clock information, determines lock status, and asserts the LOCK output high when lock occurs.
Each has a power down control to enable efficient operation in various applications.
INITIALIZATION AND LOCKING MECHANISM
Initialization of the DS99R105 and DS99R106 must be established before each device sends or receives data.
Initialization refers to synchronizing the Serializer’s and Deserializer’s PLL’s together. After the Serializers locks
to the input clock source, the Deserializer synchronizes to the Serializers as the second and final initialization
step.
1. When VDD is applied to both Serializer and/or Deserializer, the respective outputs are held in TRI-STATE and
internal circuitry is disabled by on-chip power-on circuitry. When VDD reaches VDD OK (2.2V) the PLL in
Serializer begins locking to a clock input. For the Serializer, the local clock is the transmit clock, TCLK. The
Serializer outputs are held in TRI-STATE while the PLL locks to the TCLK. After locking to TCLK, the
Serializer block is now ready to send data patterns. The Deserializer output will remain in TRI-STATE while
its PLL locks to the embedded clock information in serial data stream. Also, the Deserializer LOCK output will
remain low until its PLL locks to incoming data and sync-pattern on the RIN± pins.
2. The Deserializer PLL acquires lock to a data stream without requiring the Serializer to send special patterns.
The Serializer that is generating the stream to the Deserializer will automatically send random (non-
repetitive) data patterns during this step of the Initialization State. The Deserializer will lock onto embedded
clock within the specified amount of time. An embedded clock and data recovery (CDR) circuit locks to the
incoming bit stream to recover the high-speed receive bit clock and re-time incoming data. The CDR circuit
expects a coded input bit stream. In order for the Deserializer to lock to a random data stream from the
Serializer, it performs a series of operations to identify the rising clock edge and validates data integrity, then
locks to it. Because this locking procedure is independent on the data pattern, total random locking duration
may vary. At the point when the Deserializer’s CDR locks to the embedded clock, the LOCK pin goes high
and valid RCLK/data appears on the outputs. Note that the LOCK signal is synchronous to valid data
appearing on the outputs. The Deserializer’s LOCK pin is a convenient way to ensure data integrity is
achieved on receiver side.
DATA TRANSFER
After lock is established, the Serializer inputs DIN0–DIN23 are used to input data to the Serializer. Data is
clocked into the Serializer by the TCLK input. The edge of TCLK used to strobe the data is selectable via the
TRFB pin. TRFB high selects the rising edge for clocking data and low selects the falling edge. The Serializer
outputs (DOUT±) are intended to drive point-to-point connections or limited multi-point applications.
CLK1, CLK0, DCA, DCB are four overhead bits transmitted along the single LVDS serial data stream. The CLK1
bit is always high and the CLK0 bit is always low. The CLK1 and CLK0 bits function as the embedded clock bits
in the serial stream. DCB functions as the DC Balance control bit. It does not require any pre-coding of data on
transmit side. The DC Balance bit is used to minimize the short and long-term DC bias on the signal lines. This
bit operates by selectively sending the data either unmodified or inverted. The DCA bit is used to validate data
integrity in the embedded data stream. Both DCA and DCB coding schemes are integrated and automatically
performed within Serializer and Deserializer.
The chipset supports clock frequency ranges of 3 MHz to 40 MHz. Every clock cycle, 24 databits are sent along
with 4 additional overhead control bits. Thus the line rate is 1.12 Gbps maximum (84 Mbps minimum). The link is
extremely efficient at 86% (24/28). Twenty five (24 data + 1 clock) plus associated ground signals are reduced to
only 1 single LVDS pair providing a compression ratio of better then 25 to 1.
16 Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: DS99R105 DS99R106
DS99R105, DS99R106
www.ti.com
SNLS242D –MARCH 2007–REVISED APRIL 2013
Serialized data and clock/control bits (24+4 bits) are transmitted from the serial data output (DOUT±) at 28 times
the TCLK frequency. For example, if TCLK is , the serial rate is 40 x 28 = 1.12 Giga bits per second. Since only
24 bits are from input data, the serial “payload” rate is 24 times the TCLK frequency. For instance, if TCLK = 40
MHz, the payload data rate is 40 x 24 = 960 Mbps. TCLK is provided by the data source and must be in the
range of 3 MHz to 40 MHz nominal. The Serializer outputs (DOUT±) can drive a point-to-point connection as
shown in Figure 20. The outputs transmit data when the enable pin (DEN) is high and TPWDNB is high. The
DEN pin may be used to TRI-STATE the outputs when driven low.
When the Deserializer channel attains lock to the input from a Serializer, it drives its LOCK pin high and
synchronously delivers valid data and recovered clock on the output. The Deserializer locks onto the embedded
clock, uses it to generate multiple internal data strobes, and then drives the recovered clock to the RCLK pin.
The recovered clock (RCLK output pin) is synchronous to the data on the ROUT[23:0] pins. While LOCK is high,
data on ROUT[23:0] is valid. Otherwise, ROUT[23:0] is invalid. The polarity of the RCLK edge is controlled by the
RRFB input. ROUT(0-23), LOCK and RCLK outputs will each drive a maximum of 8 pF load with a 40 MHz clock.
REN controls TRI-STATE for ROUTn and the RCLK pin on the Deserializer.
RESYNCHRONIZATION
If the Deserializer loses lock, it will automatically try to re-establish lock. For example, if the embedded clock
edge is not detected one time in succession, the PLL loses lock and the LOCK pin is driven low. The Deserializer
then enters the operating mode where it tries to lock to a random data stream. It looks for the embedded clock
edge, identifies it and then proceeds through the locking process.
The logic state of the LOCK signal indicates whether the data on ROUT is valid; when it is high, the data is valid.
The system must monitor the LOCK pin to determine whether data on the ROUT is valid.
POWERDOWN
The Powerdown state is a low power sleep mode that the Serializer and Deserializer may use to reduce power
when no data is being transferred. The TPWDNB and RPWDNB are used to set each device into power down
mode, which reduces supply current to the µA range. The Serializer enters powerdown when the TPWDNB pin is
driven low. In powerdown, the PLL stops and the outputs go into TRI-STATE, disabling load current and reducing
supply. To exit Powerdown, TPWDNB must be driven high. When the Serializer exits Powerdown, its PLL must
lock to TCLK before it is ready for the Initialization state. The system must then allow time for Initialization before
data transfer can begin. The Deserializer enters powerdown mode when RPWDNB is driven low. In powerdown
mode, the PLL stops and the outputs enter TRI-STATE. To bring the Deserializer block out of the powerdown
state, the system drives RPWDNB high.
Both the Serializer and Deserializer must reinitialize and relock before data can be transferred. The Deserializer
will initialize and assert LOCK high when it is locked to the encoded clock.
TRI-STATE
For the Serializer, TRI-STATE is entered when the DEN or TPWDNB pin is driven low. This will TRI-STATE both
driver output pins (DOUT+ and DOUT−). When DEN is driven high, the serializer will return to the previous state
as long as all other control pins remain static (TPWDNB, TRFB).
When you drive the REN or RPWDNB pin low, the Deserializer enters TRI-STATE. Consequently, the receiver
output pins (ROUT0–ROUT23) and RCLK will enter TRI-STATE. The LOCK output remains active, reflecting the
state of the PLL. The Deserializer input pins are high impedance during receiver powerdown (RPWDNB low) and
power-off (VDD = 0V).
PRE-EMPHASIS
The DS99R105 features a Pre-Emphasis mode used to compensate for long or lossy transmission media. Cable
drive is enhanced with a user selectable Pre-Emphasis feature that provides additional output current during
transitions to counteract cable loading effects. The transmission distance will be limited by the loss
characteristics and quality of the media. Pre-Emphasis adds extra current during LVDS logic transition to reduce
the cable loading effects and increase driving distance. In addition, Pre-Emphasis helps provide faster
transitions, increased eye openings, and improved signal integrity. The ability of the DS99R105 to use the Pre-
Emphasis feature will extend the transmission distance in most cases.
Copyright © 2007–2013, Texas Instruments Incorporated Submit Documentation Feedback 17
Product Folder Links: DS99R105 DS99R106
DS99R105, DS99R106
SNLS242D –MARCH 2007–REVISED APRIL 2013
www.ti.com
AC-COUPLING AND TERMINATION
The DS99R105 and DS99R106 supports AC-coupled interconnects through integrated DC balanced
encoding/decoding scheme. To use AC coupled connection between the Serializer and Deserializer, insert
external AC coupling capacitors in series in the LVDS signal path as illustrated in Figure 20. The Deserializer
input stage is designed for AC-coupling by providing a built-in AC bias network which sets the internal VCM to
+1.2V. With AC signal coupling, capacitors provide the ac-coupling path to the signal input.
For the high-speed LVDS transmissions, the smallest available package should be used for the AC coupling
capacitor. This will help minimize degradation of signal quality due to package parasitics. The most common
used capacitor value for the interface is 100 nF (0.1 uF) capacitor.
A termination resistor across DOUT± is also required for proper operation to be obtained. The termination
resistor should be equal to the differential impedance of the media being driven. This should be in the range of
90 to 132 Ohms. 100 Ohms is a typical value common used with standard 100 Ohm transmission media. This
resistor is required for control of reflections and also to complete the current loop. It should be placed as close to
the Serializer DOUT± outputs to minimize the stub length from the pins. To match with the deferential impedance
on the transmission line, the LVDS I/O are terminated with 100 ohm resistors on Serializer DOUT± outputs pins.
PROGRESSIVE TURN–ON (PTO)
Deserializer ROUT[23:0] outputs are grouped into three groups of eight, with each group switching about 0.5UI
apart in phase to reduce EMI, simultaneous switching noise, and system ground bounce.
Applications Information
USING THE DS99R105 AND DS99R106
The DS99R105/DS99R106 Serializer/Deserializer (SERDES) pair sends 24 bits of parallel LVCMOS data over a
serial LVDS link up to 960 Mbps. Serialization of the input data is accomplished using an on-board PLL at the
Serializer which embeds clock with the data. The Deserializer extracts the clock/control information from the
incoming data stream and deserializes the data. The Deserializer monitors the incoming clockl information to
determine lock status and will indicate lock by asserting the LOCK output high.
POWER CONSIDERATIONS
An all CMOS design of the Serializer and Deserializer makes them inherently low power devices. Additionally,
the constant current source nature of the LVDS outputs minimize the slope of the speed vs. IDD curve of CMOS
designs.
NOISE MARGIN
The Deserializer noise margin is the amount of input jitter (phase noise) that the Deserializer can tolerate and still
reliably recover data. Various environmental and systematic factors include:
• Serializer: TCLK jitter, VDD noise (noise bandwidth and out-of-band noise)
• Media: ISI, VCM noise
• Deserializer: VDD noise
For a graphical representation of noise margin, please see Figure 17.
TRANSMISSION MEDIA
The Serializer and Deserializer can be used in point-to-point configuration, through a PCB trace, or through
twisted pair cable. In a point-to-point configuration, the transmission media needs be terminated at both ends of
the transmitter and receiver pair. Interconnect for LVDS typically has a differential impedance of 100 Ohms. Use
cables and connectors that have matched differential impedance to minimize impedance discontinuities. In most
applications that involve cables, the transmission distance will be determined on data rates involved, acceptable
bit error rate and transmission medium.
18 Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: DS99R105 DS99R106
DS99R105, DS99R106
www.ti.com
SNLS242D –MARCH 2007–REVISED APRIL 2013
LIVE LINK INSERTION
The Serializer and Deserializer devices support live pluggable applications. The “Hot Inserted” operation on the
serial interface does not disrupt communication data on the active data lines. The automatic receiver lock to
random data “plug & go” live insertion capability allows the DS99R106 to attain lock to the active data stream
during a live insertion event.
PCB LAYOUT AND POWER SYSTEM CONSIDERATIONS
Circuit board layout and stack-up for the LVDS SERDES devices should be designed to provide low-noise power
feed to the device. Good layout practice will also separate high frequency or high-level inputs and outputs to
minimize unwanted stray noise pickup, feedback and interference. Power system performance may be greatly
improved by using thin dielectrics (2 to 4 mils) for power / ground sandwiches. This arrangement provides plane
capacitance for the PCB power system with low-inductance parasitics, which has proven especially effective at
high frequencies, and makes the value and placement of external bypass capacitors less critical. External bypass
capacitors should include both RF ceramic and tantalum electrolytic types. RF capacitors may use values in the
range of 0.01 uF to 0.1 uF. Tantalum capacitors may be in the 2.2 uF to 10 uF range. Voltage rating of the
tantalum capacitors should be at least 5X the power supply voltage being used.
Surface mount capacitors are recommended due to their smaller parasitics. When using multiple capacitors per
supply pin, locate the smaller value closer to the pin. A large bulk capacitor is recommend at the point of power
entry. This is typically in the 50uF to 100uF range and will smooth low frequency switching noise. It is
recommended to connect power and ground pins directly to the power and ground planes with bypass capacitors
connected to the plane with via on both ends of the capacitor. Connecting power or ground pins to an external
bypass capacitor will increase the inductance of the path.
A small body size X7R chip capacitor, such as 0603, is recommended for external bypass. Its small body size
reduces the parasitic inductance of the capacitor. The user must pay attention to the resonance frequency of
these external bypass capacitors, usually in the range of 20-30 MHz range. To provide effective bypassing,
multiple capacitors are often used to achieve low impedance between the supply rails over the frequency of
interest. At high frequency, it is also a common practice to use two vias from power and ground pins to the
planes, reducing the impedance at high frequency.
Some devices provide separate power and ground pins for different portions of the circuit. This is done to isolate
switching noise effects between different sections of the circuit. Separate planes on the PCB are typically not
required. Pin Description tables typically provide guidance on which circuit blocks are connected to which power
pin pairs. In some cases, an external filter many be used to provide clean power to sensitive circuits such as
PLLs.
Use at least a four layer board with a power and ground plane. Locate LVCMOS (LVTTL) signals away from the
LVDS lines to prevent coupling from the LVCMOS lines to the LVDS lines. Closely-coupled differential lines of
100 Ohms are typically recommended for LVDS interconnect. The closely coupled lines help to ensure that
coupled noise will appear as common-mode and thus is rejected by the receivers. The tightly coupled lines will
also radiate less.
Termination of the LVDS interconnect is required. For point-to-point applications, termination should be located at
both ends of the devices. Nominal value is 100 Ohms to match the line’s differential impedance. Place the
resistor as close to the transmitter DOUT± outputs and receiver RIN± inputs as possible to minimize the resulting
stub between the termination resistor and device.
LVDS INTERCONNECT GUIDELINES
See AN-1108 (SNLA008) and AN-905 (SNLA035) for full details.
• Use 100Ωcoupled differential pairs
• Use the S/2S/3S rule in spacings
– S = space between the pair
– 2S = space between pairs
– 3S = space to LVCMOS/LVTTL signal
• Minimize the number of VIA
• Use differential connectors when operating above 500Mbps line speed
• Maintain balance of the traces
Copyright © 2007–2013, Texas Instruments Incorporated Submit Documentation Feedback 19
Product Folder Links: DS99R105 DS99R106
DIN0
DIN1
DIN2
DIN3
DIN4
DIN5
DIN6
DIN7
DIN8
DIN9
DIN10
DIN11
DIN12
DIN13
DIN14
DIN15
DIN16
DIN17
DIN18
DIN19
DIN20
DIN21
DIN22
DIN23
TCLK DOUT+
DOUT-
VDDT
VSSDR
VDDL
VSSPT0
VSSPT1
VSST
VSSL
VSSIT
VDDPT1
VDDPT0
VDDIT
VDDDR
Notes:
TPWDNB = System GPO
DEN = High (ON)
TRFB = High (Rising edge)
VODSEL = Low (400mV)
PRE = Low (OFF)
RESRVD = Low
DCAOFF = Low
DCBOFF = Low
DS99R105 (SER)
C1 C4
C2 C5
C3 C6
C7
C8
R1
C1 to C3 = 0.01 PF
C4 to C6 = 0.1 PF
C7, C8 = 100 nF; 50WVDC, NPO or X7R
R1 = 100:
LVCMOS
Parallel
Interface
Serial
LVDS
Interface
VSS
3.3V
TPWDNB
DEN
TRFB
DCAOFF
VODSEL
PRE
DCBOFF
3.3V
GPOs if used, or tie High (ON)
RESRVD
100:
100 nF
100 nF
100:
100 nF
100 nF
DOUT-
DOUT+
RIN-
RIN+
DS99R105, DS99R106
SNLS242D –MARCH 2007–REVISED APRIL 2013
www.ti.com
• Minimize skew within the pair
• Terminate as close to the TX outputs and RX inputs as possible
Additional general guidance can be found in the LVDS Owner’s Manual - available in PDF format from the TI
web site at: http://www.ti.com/ww/en/analog/interface/lvds.shtml
Figure 20. AC Coupled Application
Figure 21. DS99R105 Typical Application Connection
20 Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: DS99R105 DS99R106
ROUT0
ROUT1
ROUT2
ROUT3
ROUT4
ROUT5
ROUT6
ROUT7
ROUT8
ROUT9
ROUT10
ROUT11
ROUT12
ROUT13
ROUT14
ROUT15
ROUT16
ROUT17
ROUT18
ROUT19
ROUT20
ROUT21
ROUT22
ROUT23
RCLK
RPWDNB
REN
RRFB
RESRVD
RIN+
RIN-
VDDOR2
VDDOR3 VDDR1
VDDR0
VDDPR1
VDDPR0
Notes:
RPWDNB = System GPO
REN = High (ON)
RRFB = High (Rising edge)
RESRVD = Low
3.3V
DS99R106 (DES)
C3 C7
C4 C8
C9
C10
C5 C1
VDDIR
VDDOR1
VSSPR0
VSSPR1
VSSR0
VSSR1
VSSIR
VSSOR1
VSSOR2
VSSOR3 LOCK
C2C6
C1 to C4 = 0.01 PF
C5 to C8 = 0.1 PF
C9, C10 = 100 nF; 50WVDC, NPO or X7R
Serial
LVDS
Interface
LVCMOS
Parallel
Interface
GPO if used, or tie High (ON)
3.3V 3.3V
100:
DS99R105, DS99R106
www.ti.com
SNLS242D –MARCH 2007–REVISED APRIL 2013
Figure 22. DS99R106 Typical Application Connection
TRUTH TABLES
DS99R105 Serializer Truth Table
TPWDNB DEN Tx PLL Status LVDS Outputs
(Pin 9) (Pin 18) (Internal) (Pins 19 and 20)
L X X Hi Z
H L X Hi Z
H H Not Locked Hi Z
H H Locked Serialized Data with Embedded Clock
DS99R106 Deserializer Truth Table
ROUTn and RCLK
RPWDNB REN Rx PLL Status LOCK
(See DS99R105 Pin
(Pin 1) (Pin 48) (Internal) (Pin 17)
Diagram)
L X X Hi Z Hi Z
H L X Hi Z L = PLL Unocked;
H = PLL Locked
H H Not Locked Hi Z L
H H Locked Data and RCLK Active H
Copyright © 2007–2013, Texas Instruments Incorporated Submit Documentation Feedback 21
Product Folder Links: DS99R105 DS99R106
DS99R105, DS99R106
SNLS242D –MARCH 2007–REVISED APRIL 2013
www.ti.com
REVISION HISTORY
Changes from Revision C (April 2013) to Revision D Page
• Changed layout of National Data Sheet to TI format .......................................................................................................... 21
22 Submit Documentation Feedback Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: DS99R105 DS99R106
PACKAGE OPTION ADDENDUM
www.ti.com 10-Dec-2020
Addendum-Page 1
PACKAGING INFORMATION
Orderable Device Status
(1)
Package Type Package
Drawing Pins Package
Qty Eco Plan
(2)
Lead finish/
Ball material
(6)
MSL Peak Temp
(3)
Op Temp (°C) Device Marking
(4/5)
Samples
DS99R105SQ/NOPB ACTIVE WQFN NJU 48 250 RoHS & Green SN Level-2-260C-1 YEAR 0 to 70 DS99R105
DS99R105SQX/NOPB ACTIVE WQFN NJU 48 2500 RoHS & Green SN Level-2-260C-1 YEAR 0 to 70 DS99R105
DS99R105VS/NOPB ACTIVE TQFP PFB 48 250 RoHS & Green SN Level-3-260C-168 HR 0 to 70 DS99R105
VS
DS99R106SQ/NOPB ACTIVE WQFN NJU 48 250 RoHS & Green SN Level-2-260C-1 YEAR 0 to 70 DS99R106
DS99R106SQX/NOPB ACTIVE WQFN NJU 48 2500 RoHS & Green SN Level-2-260C-1 YEAR 0 to 70 DS99R106
DS99R106VS/NOPB ACTIVE TQFP PFB 48 250 RoHS & Green SN Level-3-260C-168 HR 0 to 70 DS99R106
VS
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
PACKAGE OPTION ADDENDUM
www.ti.com 10-Dec-2020
Addendum-Page 2
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device Package
Type Package
Drawing Pins SPQ Reel
Diameter
(mm)
Reel
Width
W1 (mm)
A0
(mm) B0
(mm) K0
(mm) P1
(mm) W
(mm) Pin1
Quadrant
DS99R105SQ/NOPB WQFN NJU 48 250 178.0 16.4 7.3 7.3 1.3 12.0 16.0 Q1
DS99R105SQX/NOPB WQFN NJU 48 2500 330.0 16.4 7.3 7.3 1.3 12.0 16.0 Q1
DS99R106SQ/NOPB WQFN NJU 48 250 178.0 16.4 7.3 7.3 1.3 12.0 16.0 Q1
DS99R106SQX/NOPB WQFN NJU 48 2500 330.0 16.4 7.3 7.3 1.3 12.0 16.0 Q1
PACKAGE MATERIALS INFORMATION
www.ti.com 15-Sep-2018
Pack Materials-Page 1
*All dimensions are nominal
Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm)
DS99R105SQ/NOPB WQFN NJU 48 250 210.0 185.0 35.0
DS99R105SQX/NOPB WQFN NJU 48 2500 367.0 367.0 38.0
DS99R106SQ/NOPB WQFN NJU 48 250 210.0 185.0 35.0
DS99R106SQX/NOPB WQFN NJU 48 2500 367.0 367.0 38.0
PACKAGE MATERIALS INFORMATION
www.ti.com 15-Sep-2018
Pack Materials-Page 2
MECHANICAL DATA
NJU0048D
www.ti.com
SQA48D (Rev A)
MECHANICAL DATA
MTQF019A – JANUARY 1995 – REVISED JANUARY 1998
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
PFB (S-PQFP-G48) PLASTIC QUAD FLATPACK
4073176/B 10/96
Gage Plane
0,13 NOM
0,25
0,45
0,75
Seating Plane
0,05 MIN
0,17
0,27
24
25
13
12
SQ
36
37
7,20
6,80
48
1
5,50 TYP
SQ
8,80
9,20
1,05
0,95
1,20 MAX 0,08
0,50 M
0,08
0°–7°
NOTES: A. All linear dimensions are in millimeters.
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-026
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2020, Texas Instruments Incorporated