Bulletin No. RSRELAY-C Drawing No. LP0498 Released 4/07 Tel +1 (717) 767-6511 Fax +1 (717) 764-0839 www.redlion.net MODEL RS - DIN RAIL RELAY SYSTEM O TERMINAL BLOCKS WITH BUILT-IN RELAY OUTPUTS O SLIM DESIGN SAVES DIN RAIL SPACE O REPLACEABLE RELAY SAVES DOWNTIME O JUMPERS SAVE WIRING TIME UL Recognized Component, File # E257265 DESCRIPTION The RS Relay System provides a compact, modular means of adding relay outputs to any transistor output device. The RSRLYB Relay Block serves as the base for a miniature, 24 volt coil relay, capable of switching up to 250 VAC at 6 Amps. Accessories, such as Jumpers, Buss Blocks, and Relay Markers are available to save installation time and money. 13. MIN. SWITCHING POWER: 120 mW 14. INPUT TO OUTPUT ISOLATION: 4 kV, 50 Hz., 1 minute 15. AMBIENT TEMPERATURE RANGE: -20 to 60C (-4 to 140F) 16. NOMINAL OPERATING MODE: 100% Duty Cycle 17. INFLAMMABILITY CLASS: VO according To UL 94 18. MECHANICAL LIFE: 20 million cycles 19. CONSTRUCTION: Case body is green, Polymide PA non-reinforced 20. CONNECTIONS: 14 AWG max. Torque 4-6 in-lb. 21. MOUNTING: Standard DIN Top Hat (T) profile rail according to EN50022 -35 x 7.5 and 35 x 15. 22. WEIGHT: 0.073 lb. (33.1 g) RELAY BLOCK-RSRLYB The RS Relay System is built around the Relay Block. The Relay Block is a 6.2 mm wide terminal block that serves as the base for the miniature plug-in relay (included). The relay has a 24 VDC coil, and its SPDT output can switch loads up to 250 VAC at 6 Amps. With its plug-in design, the relay can be replaced in seconds. The Block has a built-in suppression circuit to reduce EMC interference. Other features include an input LED, and reverse polarity protection. The RSRLYB00 is shipped in packages of 5 pieces, with the relay installed. DIMENSIONS In Inches (mm) BLOCK DIAGRAM 2-POSITION JUMPER-RSJMPR The RSJMPR Jumper can be used to bridge connections between adjacent Relay Blocks. This avoids the tedious task of wire-jumping signals such as commons or neutrals together. The maximum current capability of the RSJMPR is 6 A. The RSJMPR is available in three different colors, and is shipped in packages of 20 pieces. SPECIFICATIONS 1. NOMINAL INPUT VOLTAGE: 24 VDC 2. TYPICAL INPUT CURRENT @ 24 VDC: 9 mA 3. TYPICAL OPERATE TIME: 4 msec 4. TYPICAL RELEASE TIME: 8 msec 5. CONTACT TYPE: SPDT (Form C) 6. CONTACT MATERIAL: AgSnO 7. MAX. CONTACT VOLTAGE: 250 V AC/DC 8. MIN. CONTACT VOLTAGE: 12 V AC/DC 9. LIMITING CONTINUOUS CURRENT: 6 A 10. MAX. INRUSH CURRENT: 30 A 11. MIN. SWITCHING CURRENT: 10 mA 12. MAX. POWER RATING (RESISTIVE LOAD): 140 W SPECIFICATIONS 1. MAX. CURRENT: 6 A 2. LENGTH: 0.24" (6 mm) 3. COLOR: Available in Red, Blue, and Gray 1 CONTINUOUS JUMPER-RSCJMP BARRIER-RSBARR The RSCJMP can be used to bridge up to 80 adjacent Relay Blocks with total currents as high as 30 A. For currents above 6 A, the Buss Block must be used as the starting point. This cut-to-length jumper is available in three colors, and is shipped in packages of 2 pieces. The Barrier is always required at the start and end of a Relay System to provide protective separation according to VDC 0106-101. The Barrier should also be used to isolate adjacent Relay Blocks with voltage potentials greater than 250 V. The RSBARR is equipped with prescored breakout points at the bridging positions so that individual bridges can pass through if needed. The RSBARR00 is shipped in packages of 2 pieces. SPECIFICATIONS 1. MAX. CURRENT: 30 A 2. LENGTH: 19.7" (500 mm) 3. COLOR: Available in Red, Blue, and Gray SPECIFICATIONS BUSS BLOCK-RSBUSS RELAY MARKERS-RSMARK The 9 mm wide Buss Block is the same shape as the RSRLYB Relay Block. It can be used as a starting point for the continuous jumper in applications requiring up to 30 A. In applications that require less than 6 A, the starting point for the jumper(s) can take place at one of the Relay Blocks. The RSMARK00 Relay Markers can be used to label the Relay Blocks. After labeling or writing on the Marker, it is snapped onto the engagement lever of the Relay Block, providing a visual means of identification. The RSMARK00 is shipped in packages of 100 pieces. SPECIFICATIONS SPECIFICATIONS 1. COLOR: Black 1. MAX. CURRENT: 30 A 2. MAX. VOLTAGE: 250 V 3. CONSTRUCTION: Case body is gray, Polymide PA non-reinforced 4. CONNECTIONS: 10 AWG max. Torque 4-6 in-lb. 5. WEIGHT: 0.077 lb. (34.9 g) 1. COLOR: White ORDERING INFORMATION MODEL NO. DESCRIPTION QUANTITY/PACKAGE PART NUMBER RSRLYB Relay Block 5 RSRLYB00 RSBUSS Buss Block 1 RSBUSS00 RSBARR Barrier 2 RSBARR00 RSRSTP Rail Stop 2 RSRSTP00 2-Position Jumper Red 20 RSJMPR10 2-Position Jumper Blue 20 RSJMPR20 2-Position Jumper Gray 20 RSJMPR30 Continuous Jumper Red 2 RSCJMP10 Continuous Jumper Blue 2 RSCJMP20 Continuous Jumper Gray 2 RSCJMP30 100 RSMARK00 5 RSRLY100 RSJMPR RSCJMP RSMARK Relay Marker RSRLY1 Replacement Relay