1
O
TERMINAL BLOCKS WITH BUILT-IN RELAY OUTPUTS
O
SLIM DESIGN SAVES DIN RAIL SPACE
O
REPLACEABLE RELAY SAVES DOWNTIME
O
JUMPERS SAVE WIRING TIME
The RS Relay System is built around the Relay Block. The Relay Block is a 6.2
mm wide terminal block that serves as the base for the miniature plug-in relay
(included). The relay has a 24 VDC coil, and its SPDT output can switch loads up
to 250 VAC at 6 Amps. With its plug-in design, the relay can be replaced in
seconds. The Block has a built-in suppression circuit to reduce EMC interference.
Other features include an input LED, and reverse polarity protection. The
RSRLYB00 is shipped in packages of 5 pieces, with the relay installed.
SPECIFICATIONS
1. NOMINAL INPUT VOLTAGE: 24 VDC
2. TYPICAL INPUT CURRENT @ 24 VDC: 9 mA
3. TYPICAL OPERATE TIME: 4 msec
4. TYPICAL RELEASE TIME: 8 msec
5. CONTACT TYPE: SPDT (Form C)
6. CONTACT MATERIAL: AgSnO
7. MAX. CONTACT VOLTAGE: 250 V AC/DC
8. MIN. CONTACT VOLTAGE: 12 V AC/DC
9. LIMITING CONTINUOUS CURRENT: 6 A
10. MAX. INRUSH CURRENT: 30 A
11. MIN. SWITCHING CURRENT: 10 mA
12. MAX. POWER RATING (RESISTIVE LOAD): 140 W
13. MIN. SWITCHING POWER: 120 mW
14. INPUT TO OUTPUT ISOLATION: 4 kV, 50 Hz., 1 minute
15. AMBIENT TEMPERATURE RANGE: -20 to 60°C (-4 to 140°F)
16. NOMINAL OPERATING MODE: 100% Duty Cycle
17. INFLAMMABILITY CLASS: VO according To UL 94
18. MECHANICAL LIFE: 20 million cycles
19. CONSTRUCTION: Case body is green, Polymide PA non-reinforced
20. CONNECTIONS: 14 AWG max. Torque 4-6 in-lb.
21. MOUNTING: Standard DIN Top Hat (T) profile rail according to EN50022
–35 x 7.5 and 35 x 15.
22. WEIGHT: 0.073 lb. (33.1 g)
The RSJMPR Jumper can be used to bridge connections between adjacent
Relay Blocks. This avoids the tedious task of wire-jumping signals such as
commons or neutrals together. The maximum current capability of the RSJMPR
is 6 A. The RSJMPR is available in three different colors, and is shipped in
packages of 20 pieces.
SPECIFICATIONS
1. MAX. CURRENT: 6 A
2. LENGTH: 0.24" (6 mm)
3. COLOR: Available in Red, Blue, and Gray
MODEL RS - DIN RAIL RELAY SYSTEM
DIMENSIONS In Inches (mm)
BLOCK DIAGRAM
Bulletin No. RSRELAY-C
Drawing No. LP0498
Released 4/07
Tel +1 (717) 767-6511
Fax +1 (717) 764-0839
www.redlion.net
UL Recognized Component,
File # E257265
DESCRIPTION
The RS Relay System provides a compact, modular means of adding relay
outputs to any transistor output device. The RSRLYB Relay Block serves as the
base for a miniature, 24 volt coil relay, capable of switching up to 250 VAC at
6 Amps. Accessories, such as Jumpers, Buss Blocks, and Relay Markers are
available to save installation time and money.
2-POSITION JUMPER-RSJMPR
RELAY BLOCK-RSRLYB
The RSCJMP can be used to bridge up to 80 adjacent Relay Blocks with total
currents as high as 30 A. For currents above 6 A, the Buss Block must be used
as the starting point. This cut-to-length jumper is available in three colors, and
is shipped in packages of 2 pieces.
SPECIFICATIONS
1. MAX. CURRENT: 30 A
2. LENGTH: 19.7" (500 mm)
3. COLOR: Available in Red, Blue, and Gray
The 9 mm wide Buss Block is the same shape as the RSRLYB Relay Block.
It can be used as a starting point for the continuous jumper in applications
requiring up to 30 A. In applications that require less than 6 A, the starting point
for the jumper(s) can take place at one of the Relay Blocks.
SPECIFICATIONS
1. MAX. CURRENT: 30 A
2. MAX. VOLTAGE: 250 V
3. CONSTRUCTION: Case body is gray, Polymide PA non-reinforced
4. CONNECTIONS: 10 AWG max. Torque 4-6 in-lb.
5. WEIGHT: 0.077 lb. (34.9 g)
The Barrier is always required at the start and end of a Relay System to
provide protective separation according to VDC 0106-101. The Barrier should
also be used to isolate adjacent Relay Blocks with voltage potentials greater
than 250 V. The RSBARR is equipped with prescored breakout points at the
bridging positions so that individual bridges can pass through if needed. The
RSBARR00 is shipped in packages of 2 pieces.
SPECIFICATIONS
1. COLOR: Black
The RSMARK00 Relay Markers can be used to label the Relay Blocks. After
labeling or writing on the Marker, it is snapped onto the engagement lever of the
Relay Block, providing a visual means of identification. The RSMARK00 is
shipped in packages of 100 pieces.
SPECIFICATIONS
1. COLOR: White
MODEL NO. DESCRIPTION QUANTITY/PACKAGE PART NUMBER
RSRLYB Relay Block 5RSRLYB00
RSBUSS Buss Block 1 RSBUSS00
RSBARR Barrier 2 RSBARR00
RSRSTP Rail Stop 2 RSRSTP00
2-Position Jumper Red 20 RSJMPR10
RSJMPR 2-Position Jumper Blue 20 RSJMPR20
2-Position Jumper Gray 20 RSJMPR30
Continuous Jumper Red 2RSCJMP10
RSCJMP Continuous Jumper Blue 2RSCJMP20
Continuous Jumper Gray 2RSCJMP30
RSMARK Relay Marker 100 RSMARK00
RSRLY1 Replacement Relay 5 RSRLY100
ORDERING INFORMATION
CONTINUOUS JUMPER-RSCJMP
RELAY MARKERS-RSMARK
BARRIER-RSBARR
BUSS BLOCK-RSBUSS
