S8VS-06024A - Omron - Pdf.Support

CSM_S8VS_DS_E_7_2

Switch Mode Power Supply

S8VS (15/30/60/90/120/180/240/480-W Models)

60/90/120/180/240/480-W Models

New Models with Indication

Monitor and Simple Functions

for Easy System

Commissioning

• New 90-W models with indication monitor that

conform to UL Class 2 Output standards.

• New models with screwless terminal blocks

and indication monitor.

• Status displayed on 3-digit, 7-segment display.

• Safety standards:

UL508/60950-1,

CSA C22.2 No. 14/60950-1

(15-W and 30-W models),

CSA C22.2 No. 107.1/60950-1

(60-W to 240-W and 480-W models),

EN 50178 (= VDE0160)

• Input conditions: DC input is also possible from 80 to 370 VDC (BE models only, not compliant with EC Directives

and other safety standards).

15/30-W Models

Compact, Thin Power Supplies

That Mount Just About Anywhere

to Contribute to Control Panel

Downsizing

• Compact and thin: 22.5 × 85 × 96.5 mm (W × H × D).

• Three mounting directions

(standard, horizontal, facing horizontal).

• Mounting directly to the panel is possible.

• Safety standards:

UL508/60950-1/1604, cUL: CSA C22.2 No. 14/60950-1/213,

EN50178 (= VDE0160).

Features Common to All Models

• Mount to DIN Rail.

• Complies with SEMI F47-0706 (200-VAC input).

• RoHS-compliant.

!Refer to Safety Precautions for All Power Supplies and Safety

Precautions on page 31.

S8VS

Model Number Structure

Model Number Legend

Note: Not all combinations are possible. Refer to List of Models in Ordering Information, below.

1. Power Ratings

015: 15 W

030: 30 W

060: 60 W

090: 90 W

120: 120 W

180: 180 W

240: 240 W

480: 480 W

2. Output voltage

05: 5 V

12: 12 V

24: 24 V

3. Indication monitor

None: Without indication monitor (standard model)

A: With indication monitor (maintenance forecast monitor)

B: With indication monitor (total run time monitor)

BE: With indication monitor but without alarm output (total run

time monitor)

4. Alarm output

None: Sinking (Emitter COM) *

P: Sourcing (Collector COM)

Note: No alarm output possible with 60-W models.

*Both sinking and sourcing outputs are available for 480-W models.

5. UL Class 2 Output Standards (UL 1310)

None: Does not conform. *

S: Conforms.

*15-W, 30-W, and 60-W models conform to Class 2 output standards

(UL 1310).

Note: The S option is available only for 90-W models.

6. Terminal Block Form

None: Screw terminal block

F: Screwless terminal block

Note:

Estimates can be provided for coatings and other specifications that are not given in the datasheet. Ask your OMRON representative for details.

1234 5 6

S8VS- @@@@@@@@-@

S8VS

Ordering Information

List of Models

Note: For details on normal stock models, contact your nearest OMRON representative.

Models without Indication Monitor (Standard Models)

*1. The output capacity of the S8VS-01505 is 10 W.

*2. The output capacity of the S8VS-03005 is 20 W.

Models with Indication Monitor (Maintenance Forecast Monitor)

Models with Indication Monitor (Total Run Time Monitor)

Note: Refer to pages 29 to 30 for the options that available.

*1. DC input is possible only with BE models. The applicable range for EC Directives and other safety standards (UL, EN, etc.) is 100 to 240 VAC (85 to 264 VAC).

Power ratings Input voltage Output voltage Output current UL Class 2

Output standards

Model number

(screw terminal block)

Model number

(screwless terminal block)

15 W

100 to 240 VAC

5 V 2.0 A Yes S8VS-01505 *1

---

12 V 1.2 A Yes S8VS-01512

24 V 0.65 A Yes S8VS-01524

30 W

5 V 4.0 A Yes S8VS-03005 *2

12 V 2.5 A Yes S8VS-03012

24 V 1.3 A Yes S8VS-03024

60 W

24 V

2.5 A Yes S8VS-06024 S8VS-06024-F

90 W 3.75 A --- S8VS-09024 S8VS-09024-F

--- S8VS-09024S S8VS-09024S-F

120 W 5 A --- S8VS-12024 S8VS-12024-F

180 W 7.5 A --- S8VS-18024 S8VS-18024-F

240 W 10 A --- S8VS-24024 S8VS-24024-F

480 W 20 A

Peak current 30 A

(200 VAC) --- S8VS-48024 S8VS-48024-F

Power ratings Input voltage Output

voltage Output current Alarm

output

UL Class 2

Output standards

Model number

(screw terminal block)

Model number

(screwless terminal block)

60 W

100 to 240

VAC

(allowable

range: 85 to

264 VAC)

24 V

2.5 A --- Yes S8VS-06024A S8VS-06024A-F

90 W 3.75 A

Sinking --- S8VS-09024A S8VS-09024A-F

Sinking Yes S8VS-09024AS S8VS-09024AS-F

Sourcing --- S8VS-09024AP S8VS-09024AP-F

Sourcing Yes S8VS-09024APS S8VS-09024APS-F

120 W 5 A Sinking --- S8VS-12024A S8VS-12024A-F

Sourcing --- S8VS-12024AP S8VS-12024AP-F

180 W 7.5 A Sinking --- S8VS-18024A S8VS-18024A-F

Sourcing --- S8VS-18024AP S8VS-18024AP-F

240 W 10 A Sinking --- S8VS-24024A S8VS-24024A-F

Sourcing --- S8VS-24024AP S8VS-24024AP-F

480 W 20 A

Peak current 30 A

(200 VAC)

Sinking/

sourcing --- S8VS-48024A S8VS-48024A-F

Power ratings Input voltage Output

voltage Output current Alarm

output

UL Class 2

Output standards

Model number

(screw terminal block)

Model number

(screwless terminal block)

60 W

100 to 240

VAC

(allowable

range: 85 to

264 VAC or 80

to 370 VDC)

24 V

2.5 A --- Yes S8VS-06024B S8VS-06024B-F

90 W 3.75 A

--- --- S8VS-09024BE S8VS-09024BE-F

--- Yes S8VS-09024BES S8VS-09024BES-F

Sinking --- S8VS-09024B S8VS-09024B-F

Sinking Yes S8VS-09024BS S8VS-09024BS-F

Sourcing --- S8VS-09024BP S8VS-09024BP-F

Sourcing Yes S8VS-09024BPS S8VS-09024BPS-F

120 W 5 A

--- --- S8VS-12024BE S8VS-12024BE-F

Sinking --- S8VS-12024B S8VS-12024B-F

Sourcing --- S8VS-12024BP S8VS-12024BP-F

180 W 7.5 A

--- --- S8VS-18024BE S8VS-18024BE-F

Sinking --- S8VS-18024B S8VS-18024B-F

Sourcing --- S8VS-18024BP S8VS-18024BP-F

240 W 10 A

--- --- S8VS-24024BE S8VS-24024BE-F

Sinking --- S8VS-24024B S8VS-24024B-F

Sourcing --- S8VS-24024BP S8VS-24024BP-F

480 W 20 A

Peak current 30 A

(200 VAC)

Sinking/

sourcing --- S8VS-48024B S8VS-48024B-F

S8VS

Specifications

Ratings/Characteristics

*1. Do not use an inverter output for the Power Supply. Inverters with an output frequency of 50/60 Hz are available, but the rise in the internal

temperature of the Power Supply may result in ignition or burning.

*2. For a cold start at 25°C. Refer to Engineering Data (15-W, 30-W Models) on page 14 for details.

*3. If the output voltage adjuster (V. ADJ) is turned, the voltage will increase by more than +15% of the voltage adjustment range. When adjusting

the output voltage, confirm the actual output voltage from the Power Supply and be sure that the load is not damaged.

*4. The overvoltage protection of the S8VS-015@@ uses a zener diode clamp. If the internal feedback circuit is destroyed by any chance, the load

may be destroyed by the clamped output voltage (approx. 140% to 190% of the rated output voltage).

*5. To reset the protection, turn OFF the input power for three minutes or longer and then turn it back ON.

Power ratings 15 W 30 W

Item Type Standard Standard

Efficiency (typical)

(rated input voltage)

5-V models 72% min. 70% min.

12-V models 74% min. 76% min.

24-V models 77% min. 80% min.

Input

Voltage *1100 to 240 VAC (allowable range: 85 to 264 VAC)

Frequency *150/60 Hz (47 to 450 Hz)

Current With 100-VAC input 0.45 A max. 0.9 A max.

With 200-VAC input 0.25 A max. 0.6 A max.

Power factor ---

Harmonic current regulation Conforms to EN61000-3-2

Leakage current With 100-VAC input 0.5 mA max.

With 200-VAC input 1.0 mA max.

Inrush current *2With 100-VAC input 25 A max.

With 200-VAC input 50 A max.

Output

Voltage adjustment range *3−10% to 15% (with V.ADJ)

Ripple 2.0% (p-p) max. (at rated input/output voltage)

Input variation influence 0.5% max. (at 85- to 264-VAC input, 100% load)

Load variation influence

(rated input voltage) 2.0% max. (5 V), 1.5% max. (12 V, 24 V), (with rated input, 0 to 100% load)

Temperature variation influence 0.05%/°C max.

Startup time *2100 ms max. (at rated input/output voltage) 1,000 ms max. (at rated input/output voltage)

Hold time *220 ms min. (at rated input/output voltage)

Additional

functions

Overload protection *2105% to 160% of rated load current, inward-sloping voltage

drop, automatic reset

105% to 160% of rated load current, inverted L voltage drop,

intermittent operation, automatic reset

Overvoltage protection *2Yes (a zener diode clamp) *4Yes *5

Output voltage indication No

Output current indication No

Peak-hold current indication No

Maintenance forecast monitor indication No

Maintenance forecast monitor output No

Total run time monitor indication No

Total run time monitor output No

Undervoltage alarm indication Yes (color: red)

Undervoltage alarm output No

Parallel operation No

Series operation Models with 24-V output: Possible for up to 2 Power Supplies (with external diode)

Models with 5- or 12-V output: Not possible

Other

Operating ambient temperature Refer to the derating curve in Engineering Data (15-W, 30-W Models). (with no icing or condensation)

Storage temperature −25 to 65°C

Operating ambient humidity 25% to 85% (Storage humidity: 25% to 90%)

Dielectric strength

3.0 kVAC for 1 min. (between all inputs and outputs; detection current: 20 mA)

2.0 kVAC for 1 min. (between all inputs and PE terminals; detection current: 20 mA)

1.0 kVAC for 1 min. (between all outputs and PE terminals; detection current: 20 mA)

Insulation resistance 100 MΩ min. (between all outputs and all inputs/ PE terminals) at 500 VDC

Vibration resistance 10 to 55 Hz, 0.375-mm single amplitude for 2 h each in X, Y, and Z directions

Shock resistance 150 m/s2, 3 times each in ±X, ±Y, and ±Z directions

Output indicator Yes (color: green)

EMI

Conducted

Emissions Conforms to EN61204-3 EN55011 Class B and based on FCC Class A

Radiated Emissions Conforms to EN61204-3 EN55011 Class B

EMS Conforms to EN61204-3 high severity levels

Approved standards

UL: UL508 (Listing; Class 2 Output: Per 1310), UL1604 (Class I/Division2), UL60950-1

cUL: CSA C22.2 No.14 (Class 2 Output), No.60950-1, No.213 (Class I/Division2)

cUR: CSA C22.2 No. No.60950-1

EN/VDE: EN50178 (=VDE0160)

SEMI F47-0706 (With 200-VAC input)

Weight 160 g max. 180 g max.

S8VS

*1. Do not use an inverter output for the Power Supply. Inverters with an output frequency of 50/60 Hz are available, but the rise in the internal temperature of the Power Supply may result in

ignition or burning.

*2. For a cold start at 25°C. Refer to Engineering Data (60-W, 90-W, 120-W, 180-W, 240-W, and 480-W Models) on page 24 for details.

*3. If the output voltage adjuster (V. ADJ) is turned, the voltage will increase by more than +15% of the voltage adjustment range (by more than +10% for 240-W models with indication monitor).

When adjusting the output voltage, confirm the actual output voltage from the Power Supply and be sure that the load is not damaged.

*4. To reset the protection, turn OFF the input power for three minutes or longer and then turn it back ON.

*5. Displayed on 7-segment LED. (character height: 8 mm)

*6. Resolution of output voltage indication: 0.1 V, Precision of output voltage indication: ±2% (percentage of output voltage value, ±1 digit)

*7. Resolution of output current indication: 0.1 A; Precision of output current indication: ±5% F.S. ±1 digit max. (specified by rated output voltage)

*8. Resolution of peak-hold current indication: 0.1 A; Precision of peak-hold current indication: ±5% F.S. ±1 digit max. (specified by rated output voltage);

Signal width required for peak-hold current: 20 ms

*9. A Type and B Type: Sinking, AP Type and BP Type: Sourcing, BE Type: No alarm output.

*10. S8VS-06024A, S8VS-09024A/AP, S8VS-12024A/AP, S8VS-18024A/AP, and S8VS-24024A/AP only

*11. DC input is possible only with BE models (allowable range: 80 to 370 VDC). The applicable range for EC Directives and other safety standards (UL, EN, etc.) is 100 to 240 VAC (85 to 264

VAC).

*12. The standard 60-W, 90-W, 120-W, 180-W, and 240-W models and all 480-W models conform to EN 60950-1.

Power ratings 60 W 90 W

Item Type Standard Maintenance

forecast monitor

Total run time

monitor Standard Maintenance forecast

monitor Total run time monitor

Efficiency (typical) (rated input voltage) 78% min. 80% min.

Input

Voltage *1100 to 240 VAC (allowable range 85 to 264 VAC *1)

Frequency *150/60 Hz (47 to 450 Hz)

Current With 100-VAC input 1.7 A max. 2.3 A max.

With 200-VAC input 1.0 A max. 1.4 A max.

Power factor ---

Harmonic current regulation Conforms to EN61000-3-2

Leakage current With 100-VAC input 0.5 mA max.

With 200-VAC input 1.0 mA max.

Inrush current *2With 100-VAC input 25 A max. (17.5 A max. for BE models)

With 200-VAC input 50 A max. (35 A max. for BE models)

Output

Voltage adjustment range *3−10% to 15% (with V. ADJ) The voltage cannot be adjusted for the S8VS-09024S-@.

Ripple 2.0% (p-p) max. (at rated input/output voltage)

Input variation influence 0.5% max. (at 85- to 264-VAC input, 100% load)

Load variation influence (rated input voltage) 1.5% max. (with rated input, 0 to 100% load)

Temperature variation influence 0.05%/°C max.

Startup time *21,000 ms max. (at rated input/output voltage)

Hold time *220 ms min. (at rated input/output voltage)

Additional

functions

Overload protection *2105% to 160% of rated load current, inverted L voltage drop, intermittent, automatic reset

Overvoltage protection *2, *4Yes

Output voltage indication *5No Yes (selectable) *6 No Yes (selectable) *6

Output current indication *5No Yes (selectable) *7 No Yes (selectable) *7

Peak-hold current indication *5No Yes (selectable) *8 No Yes (selectable) *8

Maintenance forecast monitor indication *5No Yes (selectable) No No Yes (selectable) No

Maintenance forecast monitor output No Yes (transistor output),

30 VDC max., 50 mA max. *9No

Total run time monitor indication *5No Yes (selectable) No Yes (selectable)

Total run time monitor output *5No Yes (transistor output),

30 VDC max., 50 mA max. *9

Undervoltage alarm indication *5No Yes (selectable) No Yes (selectable)

Undervoltage alarm output terminals No Yes (transistor output), 30 VDC max., 50 mA max. *9

Parallel operation No

Series operation Yes for up to 2 Power Supplies (with external diode)

Other

Operating ambient temperature Refer to the derating curve in Engineering Data (60-W, 90-W, 120-W, 180-W, 240-W, and 480-W Models). (with no icing or

condensation)

Storage temperature −25 to 65°C

Operating ambient humidity 25% to 85% (Storage humidity: 25% to 90%)

Dielectric strength

3.0 kVAC for 1 min. (between all inputs and outputs/ alarm outputs; detection current: 20 mA)

2.0 kVAC for 1 min. (between all inputs and PE terminals; detection current: 20 mA)

1.0 kVAC for 1 min. (between all outputs/ alarm outputs and PE terminals; detection current for standard models: 30 mA,

detection current for models with indication monitor: 20 mA)

500 VAC for 1 min. (between all outputs and alarm outputs; detection current: 20 mA)

Insulation resistance 100 MΩ min. (between all outputs/ alarm outputs and all inputs/ PE terminals) at 500 VDC

Vibration resistance 10 to 55 Hz, 0.375-mm single amplitude for 2 h each in X, Y, and Z directions

10 to 150 Hz, 0.35-mm single amplitude (5 G max.) for 80 min each in X, Y, and Z directions

Shock resistance 150 m/s2, 3 times each in ±X, ±Y, and ±Z directions

Output indicator Yes (color: green)

EMI

Conducted

Emissions

Models with indication monitor: Conforms to EN61204-3 EN55011 Class A and based on FCC Class A, Conforms to EN61204-

3 EN55011 Class B *11

Standard models: Conforms to EN61204-3 EN55011 Group 1 Class B and based on FCC Class A

Radiated

Emissions

Models with indication monitor: Conforms to EN61204-3 EN55011 Class A, Conforms to EN61204-3 EN55011 Class B *11

Standard models: Conforms to EN61204-3 EN55011 Group 1 Class B

EMS Conforms to EN61204-3 high severity levels

Approved standards *11

UL: UL508 (Listing; Class 2 Output: Per UL1310),

UL60950-1

cUL: CSA C22.2 No.107.1 (Class 2 Output: Per

CSA C22.2 No. 223)

cUR: CSA C22.2 No.60950-1

EN/VDE: EN50178 (= VDE0160), EN60950-1

(= VDE0805 Teil 1) *12

KOSHA S Mark *10

UL: UL508 (Listing), UL60950-1

UL for S8VS-09024S-@@@S-@ only: UL508 (Listing, Class 2 Output: Per

UL1310), UL60950-1

cUL: CSA C22.2 No.107.1

cUL for S8VS-09024S-@@@S-@ only: CSA C22.2 No.107.1 (Class 2

Output: Per CSA C22.2 No. 223)

cUR: CSA C22.2 No.60950-1

EN/VDE: EN50178 (= VDE0160),

EN60950-1 (SELV) (= VDE0805 Teil 1) *12

KOSHA S Mark *10

SEMI *11 F47-0706 (With 200-VAC input)

Weight 330 g max. 490 g max.

S8VS

Note: Refer to page 5 for notes 1 to 12.

Power ratings 120 W 180 W

Item Type Standard Maintenance

forecast monitor

Total run time

monitor Standard Maintenance

forecast monitor

Total run time

monitor

Efficiency (typical) (rated input voltage) 80% min.

Input

Voltage *1100 to 240 VAC (allowable range 85 to 264 VAC *1)

Frequency *150/60 Hz (47 to 63 Hz)

Current With 100-VAC input 1.9 A max. 2.9 A max.

With 200-VAC input 1.1 A max. 1.6 A max.

Power factor 0.95 min. (0.9 A max. for BE models)

Harmonic current regulation Conforms to EN61000-3-2

Leakage current With 100-VAC input 0.5 mA max.

With 200-VAC input 1.0 mA max.

Inrush current *2With 100-VAC input 25 A max. (17.5 A max. for BE models)

With 200-VAC input 50 A max. (35 A max. for BE models)

Output

Voltage adjustment range *3−10% to 15% (with V.ADJ)

Ripple 2.0% (p-p) max. (at rated input/output voltage)

Input variation influence 0.5% max. (at 85- to 264-VAC input, 100% load)

Load variation influence

(rated input voltage) 1.5% max. (with rated input, 0 to 100% load)

Temperature variation influence 0.05%/°C max.

Startup time *21,000 ms max. (at rated input/output voltage)

Hold time *220 ms min. (at rated input/output voltage)

Additional

functions

Overload protection *2105% to 160% of rated load current, inverted L voltage drop, automatic reset

Overvoltage protection *2, *4Yes

Output voltage indication *5No Yes (selectable) *6 No Yes (selectable) *6

Output current indication *5No Yes (selectable) *7 No Yes (selectable) *7

Peak-hold current indication *5No Yes (selectable) *8 No Yes (selectable) *8

Maintenance forecast monitor indication *5No Yes (selectable) No No Yes (selectable) No

Maintenance forecast monitor output No

Yes (transistor

output), 30 VDC

max., 50 mA max.

No No

Yes (transistor

output), 30 VDC

max., 50 mA max.

Total run time monitor indication *5No Yes (selectable) No Yes (selectable)

Total run time monitor output *5No

Yes (transistor

output), 30 VDC

max., 50 mA max.

Yes (transistor

output), 30 VDC

max., 50 mA max.

Undervoltage alarm indication *5No Yes (selectable) No Yes (selectable)

Undervoltage alarm output terminals No Yes (transistor output), 30 VDC max.,

50 mA max. *9No Yes (transistor output), 30 VDC max.,

50 mA max. *9

Parallel operation No

Series operation Yes for up to 2 Power Supplies (with external diode)

Other

Operating ambient temperature Refer to the derating curve in Engineering Data (60-W, 90-W, 120-W, 180-W, 240-W, and 480-W Models). (with no icing or

condensation)

Storage temperature −25 to 65°C

Operating ambient humidity 25% to 85% (Storage humidity: 25% to 90%)

Dielectric strength

3.0 kVAC for 1 min. (between all inputs and outputs/ alarm outputs; detection current: 20 mA)

2.0 kVAC for 1 min. (between all inputs and PE terminals; detection current: 20 mA)

1.0 kVAC for 1 min. (between all outputs/ alarm outputs and PE terminals; detection current for standard models: 30 mA, detection

current for models with indication monitor: 20 mA

500 VAC for 1 min. (between all outputs and alarm outputs; detection current: 20 mA)

Insulation resistance 100 MΩ min. (between all outputs/ alarm outputs and all inputs/ PE terminals) at 500 VDC

Vibration resistance 10 to 55 Hz, 0.375-mm single amplitude for 2 h each in X, Y, and Z directions

10 to 150 Hz, 0.35-mm single amplitude (5 G max.) for 80 min each in X, Y, and Z directions

Shock resistance 150 m/s2, 3 times each in ±X, ±Y, and ±Z directions

Output indicator Yes (color: green)

EMI

Conducted

Emissions

Models with indication monitor: Conforms to EN61204-3 EN55011 Class A and based on FCC Class A, Conforms to EN61204-3

EN55011 Class B *11

Standard models: Conforms to EN61204-3 EN55011 Group 1 Class B and based on FCC Class A

Radiated Emissions Models with indication monitor: Conforms to EN61204-3 EN55011 Class A, Conforms to EN61204-3 EN55011 Class B *11

Standard models: Conforms to EN61204-3 EN55011 Group 1 Class B

EMS Conforms to EN61204-3 high severity levels

Approved standards *11

UL: UL508 (Listing), UL60950-1

cUL: CSA C22.2 No. 107.1

cUR: CSA C22.2 No. 60950-1

EN/VDE: EN50178 (= VDE0160), EN60950-1 (SELV) (= VDE0805 Teil 1) *12

KOSHA S Mark *10

SEMI *11 F47-0706 (200-VAC input)

Weight 550 g max. 850 g max.

S8VS

Note: Refer to page 5 for notes 1 to 12.

Power ratings 240 W 480 W

Item Type Standard Maintenance

forecast monitor

Total run time

monitor Standard Maintenance

forecast monitor

Total run time

monitor

Efficiency (typical) (rated input voltage) 80% min. 83% min.

Input

Voltage *1100 to 240 VAC (allowable range 85 to 264 VAC)

Frequency *150/60 Hz (47 to 63 Hz)

Current With 100-VAC input 3.8 A max. 7.4 A max.

With 200-VAC input 2.0 A max. 3.9 A max.

Power factor 0.95 min. (0.9 A max. for BE models) 0.95 min.

Harmonic current regulation Conforms to EN61000-3-2

Leakage current With 100-VAC input 0.5 mA max.

With 200-VAC input 1.0 mA max.

Inrush current *2With 100-VAC input 25 A max. (17.5 A max. for BE models) 25 A max.

With 200-VAC input 50 A max. (35 A max. for BE models) 50 A max.

Output

Voltage adjustment range *3

Models with indication monitor (except for BE models): Å}10%

(with V. ADJ)

Standard models (except for BE models): −10% to 15% (with

V.ADJ)

−10% to 15% (with V.ADJ)

Ripple 2.0% (p-p) max. (at rated input/output voltage)

Input variation influence 0.5% max. (at 85- to 264-VAC input, 100% load)

Load variation influence

(rated input voltage) 1.5% max. (with rated input, 0 to 100% load)

Temperature variation influence 0.05%/°C max.

Startup time *21,000 ms max. (at rated input/output voltage)

Hold time *220 ms min. (at rated input/output voltage)

Additional

functions

Overload protection *2105% to 160% of rated load current, inverted L voltage drop, automatic reset

Overvoltage protection *2, *4Yes

Output voltage indication *5No Yes (selectable) *6 No Yes (selectable) *6

Output current indication *5No Yes (selectable) *7 No Yes (selectable) *7

Peak-hold current indication *5No Yes (selectable) *8 No Yes (selectable) *8

Maintenance forecast monitor indication *5No Yes (selectable) No Yes (selectable) No

Maintenance forecast monitor output No

Yes (transistor

output), 30 VDC

max., 50 mA max. *9

Yes (transistor

output), 30 VDC

max., 50 mA max.

Total run time monitor indication *5No Yes (selectable) No Yes (selectable)

Total run time monitor output *5No

Yes (transistor

output), 30 VDC

max., 50 mA max. *9

Yes (transistor

output), 30 VDC

max., 50 mA max. *9

Undervoltage alarm indication *5No Yes (selectable) No Yes (selectable)

Undervoltage alarm output terminals No Yes (transistor output), 30 VDC max., 50 mA

max. *9No Yes (transistor output), 30 VDC max., 50 mA

max. *9

Parallel operation No

Series operation Yes for up to 2 Power Supplies (with external diode)

Other

Operating ambient temperature Refer to the derating curve in Engineering Data (60-W, 90-W, 120-W, 180-W, 240-W, and 480-W Models). (with no icing or

condensation)

Storage temperature −25 to 65°C

Operating ambient humidity 25% to 85% (Storage humidity: 25% to 90%)

Dielectric strength

3.0 kVAC for 1 min. (between all inputs and outputs/alarm outputs; detection current: 20 mA)

2.0 kVAC for 1 min. (between all inputs and PE terminals; detection current: 20 mA)

1.0 kVAC for 1 min. (between all outputs/ alarm outputs and PE terminals; detection current for standard 240-W and 480-W

models: 30 mA, detection current for 240-W models with indication monitor: 20 mA)

500 VAC for 1 min. (between all outputs and alarm outputs; detection current: 20 mA)

Insulation resistance 100 MΩ min. (between all outputs/ alarm outputs and all inputs/ PE terminals) at 500 VDC

Vibration resistance

10 to 55 Hz, 0.375-mm single amplitude for 2 h each in X, Y, and Z directions

10 to 150 Hz, 0.35-mm single amplitude (5 G max.) for 80 min each in X, Y, and Z directions: 240 W

10 to 150 Hz, 0.35-mm single amplitude (3 G max.) for 80 min each in X, Y, and Z directions: 480 W

Shock resistance 150 m/s2, 3 times each in ±X, ±Y, and ±Z directions

Output indicator Yes (color: green)

EMI

Conducted

Emissions

Models with indication monitor: Conforms to EN61204-3

EN55011 Class A and based on FCC Class A, Conforms to

EN61204-3 EN55011 Class B *11

Standard models: Conforms to EN61204-3 EN55011 Group 1

Class B and based on FCC Class A

Conforms to EN61204-3 EN55011 Class A and based on FCC

Class A

Conforms to EN61204-3 EN55011 Class B *11

Radiated Emissions

Models with indication monitor: Conforms to EN61204-3

EN55011 Class A, Conforms to EN61204-3 EN55011 Class B

*11

Standard models: Conforms to EN61204-3 EN55011 Group 1

Class B

Conforms to EN61204-3 EN55011 Class A

Conforms to EN61204-3 EN55011 Class B *11

EMS Conforms to EN61204-3 high severity levels

Approved standards *11

UL: UL508 (Listing), UL60950-1

cUL: CSA C22.2 No.107.1,

cUR: CSA No. 60950-1,

EN/VDE: EN50178 (=VDE0160),

EN60950-1 (=VDE0805 Teil 1) *12

KOSHA S Mark *10

SEMI *11 F47-0706 (200-VAC input)

Weight 1,150 g max. 1,700 g max.

S8VS

Connections

Block Diagrams

Noise filter

AC (L)

INPUT

AC (N)

−V

DC OUTPUT

Fuse

2.5 A

Voltage

detection circuit

Photocoupler

Drive control

circuit

Overcurrent

detection circuit

Inrush current

protection

circuit

Rectifier/

smoothing

circuit

Rectifier/

smoothing

circuit

Undervolt-

age

indicator

Overvoltage

protection

S8VS-015@@ (15 W)

−V

DC OUTPUT

Voltage

detection circuit

Photocoupler

Rectifier/smoothing circuit

Noise filter

AC (L)

INPUT

AC (N)

Drive control

circuit

Fuse 3.15 A

Overcurrent

circuit

Current detection

circuit

Overvoltage

detection circuit

Inrush current

protection

circuit

Rectifier/

smoothing

circuit

Undervolt-

age

indicator

S8VS-030@@ (30 W)

AC (L)

INPUT

AC (N)

−V

DC OUTPUT

Voltage

detection circuit

Photocoupler

Rectifier/smoothing circuit

Rectifier/

smoothing

circuit

Noise filter

Drive control

circuit

Fuse

3.15 A

Overcurrent

circuit

Current detection

circuit

Arithmetic

operation circuit

Display circuit

Switch

Overvoltage

detection circuit

Inrush current

protection

circuit

S8VS-06024A (60 W)

S8VS-06024B (60 W)

AC (L)

INPUT

AC (N)

DC OUTPUT

−V

Voltage

detection circuit

Photocoupler

Rectifier/smoothing circuit

Rectifier/

smoothing

circuit

Noise filter

Drive control

circuit

Fuse

6.3 A

Overcurrent

circuit

Current detection

circuit

Arithmetic

operation circuit

Display circuit

Switch

Overvoltage

detection circuit

Inrush

current

protection

circuit

Rectifier

S8VS-06024A-F (60 W)

S8VS-06024B-F (60 W)

S8VS

S8VS-06024-@ (60 W)

AC (L)

INPUT

AC (N)

−V

DC OUTPUT

Fuse

6.3 A

Rectifier

Voltage

detection circuit

Photocoupler

Rectifier/smoothing circuit

Noise filter

Drive control

circuit

Overcurrent

circuit

Current detection

circuit

Overvoltage

detection circuit

Inrush current

protection

circuit

Smooth-

ing

circuit

−V

Voltage

detection circuit

Photocoupler

Rectifier/smoothing circuit

Rectifier/

smoothing

circuit

Noise filter

AC (L)

INPUT

AC (N)

Drive control

circuit

Alarm

DC Low

Yrs/kh

Common

DC OUTPUT

Fuse 4.0 A

Overcurrent

circuit

Arithmetic

operation circuit

Display circuit

Switch

Overvoltage

detection circuit

Current detection

circuit

Rectifier/smoothing circuit

Arithmetic

operation circuit

Display circuit

Switch

Photocoupler

Alarm

DC Low

Yrs/kh

Common

Sinking type (S8VS-09024A, S8VS-09024B) Sourcing type (S8VS-09024AP, S8VS-09024BP)

Inrush current

protection

circuit

S8VS-09024A@ (90 W)

S8VS-09024B@ (90 W)

Switch

Sinking type

(S8VS-09024A-F, S8VS-09024B-F,

S8VS-09024AS-@, S8VS-09024BS-@)

Sourcing type

(S8VS-09024AP-F, S8VS-09024BP-F,

S8VS-09024APS-@, S8VS-09024BPS-@)

Rectifier/smoothing circuit

Arithmetic

operation circuit

Display circuit

Switch

Type with no alarm output

(S8VS-09024BE-@, S8VS-09024BES-@)

Rectifier

−V

Voltage

detection circuit

Photocoupler

Rectifier/smoothing circuit

Rectifier/

smoothing

circuit

Noise filter

AC (L)

INPUT

AC (N)

Drive control

circuit

Alarm

DC Low

Yrs/kh

Common

DC OUTPUT

Fuse 8.0 A

Overcurrent

circuit

Arithmetic

operation circuit

Display circuit

Overvoltage

detection circuit

Current detection

circuit

Rectifier/smoothing circuit

Arithmetic

operation circuit

Display circuit

Switch

Photocoupler

Alarm

DC Low

Yrs/kh

Common

Inrush current

protection

circuit

S8VS-09024A-F (90 W)

S8VS-09024B-F (90 W)

S8VS-09024AS-@ (90 W)

S8VS-09024BS-@ (90 W)

S8VS-09024AP-F (90 W)

S8VS-09024BP-F (90 W)

S8VS-09024APS-@ (90 W)

S8VS-09024BPS-@ (90 W)

S8VS-09024BE-@ (90 W)

S8VS-09024BES-@ (90 W)

S8VS

S8VS-09024-@ (90 W)

S8VS-09024S-@ (90 W)

DC OUTPUT

INPUT

AC (L)

AC (N)

−V

Fuse

8.0 A

Rectifier

Voltage

detection circuit

Photocoupler

Rectifier/smoothing circuit

Noise filter

Drive control

circuit

Overcurrent

circuit

Current detection

circuit

Overvoltage

detection circuit

Inrush current

protection

circuit

Smooth-

ing

circuit

Noise filter

AC (L)

INPUT

AC (N)

Yrs/kh

Common

−V

DC OUTPUT

Fuse 3.5 A

Display circuit Switch

Rectifier

Inrush

current

protection

circuit

Drive control

circuit

Overcurrent

circuit

Sinking type (S8VS-12024A, S8VS-12024B)

Rectifier/smoothing circuit

Arithmetic

operation circuit

Photocoupler

Alarm

DC Low

Rectifier/smoothing circuit

Photocoupler

Voltage

detection circuit

Overvoltage

detection circuit

Sourcing type (S8VS-12024AP, S8VS-12024BP)

Rectifier/smoothing circuit

Arithmetic

operation circuit

Display circuit

Switch

Photocoupler

Alarm

DC Low

Yrs/kh

Common

Harmonic

current

suppression

Smooth-

ing circuit

S8VS-12024A@ (120 W)

S8VS-12024B@ (120 W)

Noise filter

AC (L)

INPUT

AC (N)

Yrs/kh

Common

−V

DC OUTPUT

Fuse 5.0 A

Display circuit Switch

Rectifier

Inrush current

protection

circuit

Drive control

circuit

Overcurrent

circuit

Rectifier/smoothing circuit

Arithmetic

operation circuit

Photocoupler

Alarm

DC Low

Rectifier/smoothing circuit

Photocoupler

Voltage

detection circuit

Overvoltage

detection circuit

Rectifier/smoothing circuit

Arithmetic

operation circuit

Display circuit

Switch

Photocoupler

Alarm

DC Low

Yrs/kh

Common

Harmonic

current

suppression

Smooth-

ing circuit

Sinking type (S8VS-12024A-F, S8VS-12024B-F) Sourcing type (S8VS-12024AP-F, S8VS-12024BP-F)

Rectifier/smoothing circuit

Arithmetic

operation circuit

Display circuit

Switch

Type with no alarm output (S8VS-12024BE-@)

S8VS-12024A-F (120 W)

S8VS-12024B-F (120 W)

S8VS-12024AP-F (120 W)

S8VS-12024BP-F (120 W)

S8VS-12024BE-@ (120 W)

S8VS

S8VS-12024-@ (120 W)

Photocoupler

Rectifier/smoothing circuit

INPUT

−V

DC OUTPUT

AC (L)

AC (N)

Fuse

5.0 A

Rectifier

Voltage

detection circuit

Noise filter

Drive control

circuit

Overvoltage

detection circuit

Inrush current

protection

circuit

Smooth-

ing

circuit

Harmonic

current

suppression

Overcurrent

detection circuit

Noise filter

AC (L)

INPUT

AC (N)

Yrs/kh

Common

−V

DC OUTPUT

Fuse 6 A

Display circuit Switch

Inrush current

protection

circuit

Drive control

circuit

Photocoupler

Sinking type (S8VS-18024A, S8VS-18024B) Sourcing type (S8VS-18024AP, S8VS-18024BP)

Rectifier/smoothing circuit

Arithmetic

operation circuit

Alarm

DC Low

Rectifier/smoothing circuit

Voltage

detection circuit

Overvoltage

detection circuit

Rectifier/smoothing circuit

Arithmetic

operation circuit

Display circuit

Switch

Alarm

DC Low

Yrs/kh

Common

Rectifier Harmonic

current

suppression

Smooth-

ing circuit

Overcurrent

detection circuit

S8VS-18024A@ (180 W)

S8VS-18024B@ (180 W)

Noise filter

AC (L)

INPUT

AC (N)

Yrs/kh

Common

−V

DC OUTPUT

Fuse 6.3 A

Display circuit Switch

Inrush current

protection

circuit

Drive control

circuit

Photocoupler

Rectifier/smoothing circuit

Arithmetic

operation circuit

Alarm

DC Low

Rectifier/smoothing circuit

Voltage

detection circuit

Overvoltage

detection circuit

Rectifier/smoothing circuit

Arithmetic

operation circuit

Display circuit

Switch

Alarm

DC Low

Yrs/kh

Common

Rectifier Harmonic

current

suppression

Smooth-

ing circuit

Overcurrent

detection circuit

Sinking type (S8VS-18024A-F, S8VS-18024B-F) Sourcing type (S8VS-18024AP-F, S8VS-18024BP-F)

Rectifier/smoothing circuit

Arithmetic

operation circuit

Display circuit

Switch

Type with no alarm output (S8VS-18024BE-@)

S8VS-18024A-F (180 W)

S8VS-18024B-F (180 W)

S8VS-18024AP-F (180 W)

S8VS-18024BP-F (180 W)

S8VS-18024BE-@ (180 W)

S8VS

S8VS-18024-@ (180 W)

Photocoupler

INPUT

Rectifier/smoothing circuit

−V

DC OUTPUT

Fuse

6.3 A

AC (L)

AC (N)

Rectifier

Voltage

detection circuit

Noise filter

Drive control

circuit

Overvoltage

detection circuit

Inrush current

protection

circuit

Smooth-

ing

circuit

Harmonic

current

suppression

Overcurrent

detection circuit

Noise filter

AC (L)

INPUT

AC (N)

Yrs/kh

Common

−V

DC OUTPUT

Fuse 7.5 A

Display circuit Switch

Inrush current

protection

circuit

Drive control

circuit

Photocoupler

Sinking type (S8VS-24024A, S8VS-24024B) Sourcing type (S8VS-24024AP, S8VS-24024BP)

Rectifier/smoothing circuit

Arithmetic

operation circuit

Photocoupler

Alarm

DC Low

Rectifier/smoothing circuit

Overcurrent

circuit

Voltage

detection circuit

Overvoltage

detection circuit

Current

detection circuit

Rectifier/smoothing circuit

Arithmetic

operation circuit

Display circuit

Switch

Photocoupler

Alarm

DC Low

Yrs/kh

Common

Rectifier Harmonic

current

suppression

Smooth-

ing circuit

S8VS-24024A@ (240 W)

S8VS-24024B@ (240 W)

Noise filter

AC (L)

INPUT

AC (N)

Yrs/kh

Common

−V

DC OUTPUT

Fuse 8.0 A

Display circuit Switch

Inrush current

protection

circuit

Drive control

circuit

Photocoupler

Rectifier/smoothing circuit

Arithmetic

operation circuit

Photocoupler

Alarm

DC Low

Rectifier/smoothing circuit

Overcurrent

circuit

Voltage

detection circuit

Overvoltage

detection circuit

Current

detection circuit

Rectifier/smoothing circuit

Arithmetic

operation circuit

Display circuit

Switch

Photocoupler

Alarm

DC Low

Yrs/kh

Common

Rectifier Harmonic

current

suppression

Smoothing

circuit

Sinking type (S8VS-24024A-F, S8VS-24024B-F) Sourcing type (S8VS-24024AP-F, S8VS-24024BP-F)

Rectifier/smoothing circuit

Arithmetic

operation circuit

Display circuit

Switch

Type with no alarm output (S8VS-24024BE-@)

S8VS-24024A-F (240 W)

S8VS-24024B-F (240 W)

S8VS-24024AP-F (240 W)

S8VS-24024BP-F (240 W)

S8VS-24024BE-@ (240 W)

S8VS

S8VS-24024-@ (240 W)

DC OUTPUT

INPUT

Photocoupler

Rectifier/smoothing circuit

−V

Fuse

8.0 A

AC (L)

AC (N)

Rectifier

Voltage

detection circuit

Noise filter

Drive control

circuit

Overvoltage

detection circuit

Inrush current

protection

circuit

Smooth-

ing

circuit

Harmonic

current

suppression

Overcurrent

detection circuit

Drive circuit

Auxiliary power

supply circuit

Control

circuit

−V

DC OUTPUT

Fuse 12A

AC (L)

INPUT

AC (N)

DC LOW

Yrs/kh

Sinking/Sourcing

S8VS-48024A/B

−V

Noise filter

Rectifier Rectifier/

smoothing circuit

Rectifier/

smoothing

circuit

Photocoupler

Display

circuit Switch

Harmonic

current

suppression

Smoothing

circuit

Inrush

current

protection

circuit

Voltage

detection circuit

Overvoltage

detection circuit

Overcurrent

circuit

Current

detection circuit

Arithmetic

operation

circuit

S8VS-48024-@ (480 W)

S8VS-48024A-@ (480 W)

S8VS-48024B-@ (480 W)

S8VS

Construction and Nomenclature (15-W, 30-W Models)

Nomenclature

15-W, 30-W Models S8VS-015@@/S8VS-030@@

Note: The S8VS-01505 is shown above.

Engineering Data (15-W, 30-W Models)

Derating Curve

S8VS-015@@

S8VS-03005/S8VS-03012

S8VS-03024

Note: 1. Internal parts may occasionally deteriorate or be damaged.

Do not use the Power Supply in areas outside the derating

curve (i.e., the area shown by shading A in the above

graph).

2. If there is a derating problem, use forced air-cooling.

3. Provide a space of at least 20 mm when using standard

mounting and horizontal mounting. If 20 mm is not available,

make sure that the space is at least 10 mm. In this case,

reduce the corresponding derating curve by 5°C.

*1. The fuse is located on the (L) side. It is NOT user-replaceable.

*2. This is the protective earth terminal specified in the safety standards. Always ground this terminal.

No. Name Function

1 AC Input terminals (L), (N) Connect the input lines to these terminals. *1

2 Protective Earth terminal (PE) Connect the ground line to this terminal. *2

3 DC Output terminals (−V), (+V) Connect the load lines to these terminals.

4 Output indicator (DC ON: Green) Lights while a direct current (DC) output is ON.

5 Undervoltage indicator (DC LOW: Red) Lights when a drop is detected in the output voltage.

6 Output voltage adjuster (V.ADJ) Use to adjust the voltage.

−20 −10 0 10 20 30 40 50 60 70 80

120

100

*1 Standard mounting

*2 Face-up mounting

*3 Horizontal mounting

Ambient temperature (°C)

Load ratio (%)

−20 −10 0 10 20 30 40 50 60 70 80

120

100

*1 Standard mounting

*2 Face-up mounting/Horizontal mounting

Ambient temperature (°C)

Load ratio (%)

−20 −10 0 10 20 30 40 50 60 70 80

120

100

*1 Standard mounting

*2 Face-up mounting/Horizontal mounting

Ambient temperature (°C)

Load ratio (%)

S8VS

Mounting

Note: 1. Improper mounting will interfere with heat dissipation and

may occasionally result in deterioration or damage of

internal parts. Use the Product within the derating curve for

the mounting direction that is used. Do not use the Power

Supply mounted in any way not shown above.

2. Use a mounting bracket (S82Y-VS30P, sold separately)

when the Product is mounted horizontally.

3. Heat dissipation will be adversely affected. When the

Product is mounted facing horizontally, always place the

side with the label facing horizontally.

4. Use PFP-M End Plates on the top and bottom of the Power

Supply when mounting horizontally on a DIN rail.

Overload Protection

The load and the power supply are automatically protected from

overcurrent damage by this function.

Overload protection is activated if the output current rises above

105% of the rated current.

When the output current returns within the rated range overload

protection is automatically cleared.

Note: 1. Internal parts may occasionally deteriorate or be damaged

if a short-circuited or overcurrent state continues during

operation.

2. Internal parts may possibly deteriorate or be damaged if the

Power Supply is used for applications with frequent inrush

current or overloading at the load end. Do not use the Power

Supply for such applications.

Overvoltage Protection

Consider the possibility of an overvoltage and design the system so

that the load will not be subjected to an excessive voltage even if the

feedback circuit in the Power Supply fails.

This power supply automatically protects itself and the load from

overvoltage.

Overvoltage protection is activated if the output voltage rises above

approx. 130% of the rated output voltage.

To reset the power supply, leave the power supply off for more than

3 minutes and then turn it on again.

Note: 1. Do not turn ON the power again until the cause of the

overvoltage has been removed.

2. The overvoltage protection of the S8VS-015@@ uses a

zener diode clamp. The output voltage will be clamped at

approx. 140% or higher of the rated output voltage. If the

internal feedback circuit is destroyed by any chance, the

load may be destroyed by the clamped output voltage

(approx. 140% to 190% of the rated output voltage). The

power Supply will not restart if the output is turned OFF by

the overvoltage protection operation. If this occurs, replace

the Power Supply.

Inrush Current, Startup Time, Output Hold Time

Undervoltage Alarm Indication

LED (DC LOW: red) lights to warn of output voltage drop.

Detection voltage is set to approx. 80% (75 to 90%) of the rated output

voltage.

Note: This function monitors the voltage at the power supply output

terminals. To check actual voltage, measure voltage on the

load side.

Face-up mounting with DIN rail

S82Y-VS30P

Side with label

Horizontal mounting with S82Y-VS30P*

Standard mounting with DIN rail

Face-up mounting with S82Y-VS30P

Standard mounting with S82Y-VS30P

Note: The Side-mounting Bracket can be mounted from either side.

0 10050

Output voltage (V)

Output current (%)

0 10050

Output current (%)

Output voltage (V)

Intermittent

operation

15-W Models 30-W Models

The values shown in the above diagrams are for reference only.

+15%

−10%

0 V

+30%

(approx.)

Overvoltage protection

operating

Variable range

Rated output

voltage

Output voltage (V)

The values shown in the above diagram is for reference only.

90%

96.5%

Startup time (1,000 ms max.)

AC input

voltage

AC input

current

Output

voltage

Inrush current on input application

Input OFF

Input ON

Hold time

(20 ms min.)

S8VS

Construction and Nomenclature (60-W, 90-W, 120-W, 180-W, 240-W, and 480-W Models)

Nomenclature

*The terminal arrangement is the same for models with screwless

terminal blocks and standard models.

*1. The fuse is located on the (L) side. For a DC input, connect the

positive voltage to the L terminal.

*2. This is the protective earth terminal specified in the safety

standards. Always ground this terminal.

*3. The output voltage cannot be adjusted for the

S8VS-09024@@@S.

*4. S8VS-@@@24A@@/B@@/BE@ only.

*5. S8VS-@@@24A@@/B@@ only (except the S8VS-06024@).

*6. Both sinking and sourcing outputs are available.

*7. S8VS-@@@24A@@ only (excluding S8VS-06024A).

*8. S8VS-@@@24B@@ only (excluding S8VS-06024B).

60-W Models

Standard Model

S8VS-06024

Models with Indication Monitor

S8VS-06024@

Note: The S8VS-06024A is shown above.

90-W/120-W Models

Standard Models

S8VS-09024/S8VS-0924S/

S8VS-12024

Models with Indication Monitor

S8VS-09024@@@/

S8VS-09024@@@S/S8VS-12024@@@

Note: The S8VS-12024A is shown above.

180-W Models

Standard Model

S8VS-18024

Models with Indication Monitor

S8VS-18024@@@

Note: The S8VS-18024A is shown above.

240-W Models

Standard Model

S8VS-24024

Models with Indication Monitor

S8VS-24024@@@

Note: The S8VS-24024A is shown above.

11 13

1311

No. Name Function

1AC Input terminals

(L), (N) Connect the input lines to these

terminals. *1

2Protective Earth

terminal (PE) Connect the ground line to this

terminal. *2

3DC Output terminals

(−V), (+V) Connect the load lines to these

terminals.

4Output indicator

(DC ON: Green) Lights while a direct current (DC)

output is ON.

5Output voltage

adjuster (V.ADJ) Use to adjust the voltage. *3

6 Main display (Red) *4Indicates the measurement or set

value.

7Operation

indicator

(Orange) *4

VLights up when the output voltage is

indicated. Blinks during setup of

undervoltage alarm value.

ALights up during indication of output

current.

Apk Lights up during indication of peak

hold current.

Yrs

Lights up during indication of

maintenance forecast monitor.

Blinks during setup of maintenance

forecast monitor setting. (S8VS-

@@@24A@@)

Lights up during indication of total

run time monitor. Blinks during setup

of total run time monitor. (S8VS-

@@@24B@@)

8 Mode Key *4Use the Mode Key to change the

indicated parameter or reset the

peak hold current value.

9Up Key *5Use the Up Key to change to the

setting mode or to increase the set

value.

10 Down Key *5Use the Down Key to change to the

setting mode or to decrease the set

value.

Alarm

outputs

*5, *6

Undervoltage

output

terminal (DC

Low)

Output when a drop is detected in

the output voltage (voltage drop =

transistor OFF).

Maintenance

Forecast

output

terminal (Yrs)

Output when the set value for

maintenance is reached (transistor

OFF).

Total run time

output

terminal (kh)

Output when the set value for total

run time is reached (transistor OFF).

13 Common

terminal Common terminal (emitter) for

terminals 11 and 12.

S8VS

*The terminal arrangement is the same for models with screwless

terminal blocks and standard models.

*1. The fuse is located on the (L) side. It is NOT user replaceable.

*2. This is the protective earth terminal specified in the safety standards.

Always ground this terminal.

*3. S8VS-48024A/B only.

*4. S8VS-48024A only.

*5. S8VS-48024B only.

480-W Models

Standard Model

S8VS-48024

Models with Indication Monitor

S8VS-48024@

1 2

13 11

1 2

Note: The illustration shows the S8VS-48024A model.

No. Name Function

1AC Input terminals

(L), (N) Connect the input lines to these

terminals. *1

2Protective Earth

terminal (PE) Connect the ground line to this

terminal. *2

3DC Output terminals

(−V), (+V) Connect the load lines to these

terminals.

4Output indicator

(DC ON: Green) Lights while a direct current (DC)

output is ON.

5Output voltage adjuster

(V.ADJ) Use to adjust the voltage.

6 Main display (Red) *3Indicates the measurement or set

value.

7Operation

indicator

(Orange) *3

VLights up when the output voltage is

indicated. Blinks during setup of

undervoltage alarm value.

ALights up during indication of output

current.

Apk Lights up during indication of peak

hold current.

Yrs

Lights up during indication of

maintenance forecast monitor.

Blinks during setup of maintenance

forecast monitor setting. (S8VS-

48024A)

Lights up during indication of total

run time monitor. Blinks during setup

of total run time monitor. (S8VS-

48024B)

8 Mode Key *3Use the Mode Key to change the

indicated parameter or reset the

peak hold current value.

9Up Key *3Use the Up Key to change to the

setting mode or to increase the set

value.

10 Down Key *3Use the Down Key to change to the

setting mode or to decrease the set

value.

Alarm

outputs

Undervoltage

output terminal

(DC Low)

(Emitter side) Output when a drop is detected in

the output voltage (voltage drop =

transistor OFF).

Undervoltage

output terminal

(DC Low)

(Collector side)

Maintenance

Forecast

output terminal

(Yrs) *4

(Emitter side)

Output when the set value for

maintenance is reached (transistor

OFF).

Total run time

output terminal

(kh) *5

(Emitter side)

Output when the set value for total

run time is reached (transistor OFF).

Maintenance

Forecast

output terminal

(Yrs) *4

(Collector side)

Output when the set value for

maintenance is reached (transistor

OFF).

Total run time

output terminal

(kh) *5

(Collector side)

Output when the set value for total

run time is reached (transistor OFF).

15,

16 NC (Not connected)

S8VS

Mode Change (S8VS-@@@24A@@/S8VS-@@@24B@@/S8VS-@@@24BE@ Only)

S8VS-@@@24A@@ models (with display monitor) can display the output voltage, output current, peak hold current, or maintenance forecast

monitor time. S8VS-@@@24B@@/S8VS-@@@24BE@ models (with display monitor) can display the output voltage, output current, peak hold

current, or total run time.

Note: No setting mode is provided for the S8VS-06024@.

Operation Mode

Various states of the Power Supply are indicated.

Note: 1. The peak hold current starts measuring the current 3 seconds after the Power Supply is started. Inrush current is thus not measured.

2. For the factory setting, the output voltage will be displayed when the power supply is first turned ON. Thereafter, the output voltage will

be indicated in the same display when shutting down.

Setting Mode (Except for S8VS-06024@)

Set various parameters of the Power Supply.

Note: 1. Press and hold the (9) Up Key U or (10) Down Key D for two seconds or more to increase or decrease the value rapidly.

2. The S8VS-06024@ is not provided with the setting mode and its parameters are fixed at the shipment setting.

Power-ON

Operation mode

Press Mode key and

hold for three seconds or more.

Or no key operation for 30 seconds or more.

Model indication

Setting mode

Press and hold

Up key U or Down Key D

for three seconds or more.

Output voltage

(Voltage output by Power Supply is

monitored and displayed.)

Output current

(Current output by Power Supply is

monitored and displayed.)

Peak hold current

(Maximum current output by Power Supply is

recorded and displayed.)

Total run time monitor

Output voltage

(Voltage output by Power Supply is

monitored and displayed.)

Output current

(Current output by Power Supply is

monitored and displayed.)

Peak hold current (See note 1.)

(Maximum current output by Power Supply is

recorded and displayed.)

Maintenance forecast monitor

Models with Maintenance Forecast Monitor (S8VS-@@@24A@@) Models with Total Run Time Monitor (S8VS-@@@24B@@/

S8VS-@@@24BE@)

Operation Mode

Undervoltage

detected

Total run

time 1,000-hour steps

1 to 50 to 150 ( ×

1000 h)

Press 3 seconds or more or no key

pressed for 30 seconds or more.

Press 3 seconds

or more.

* Factory settings are in

reverse type.

Models with Maintenance Forecast Monitor (S8VS-@@@24A@@) Models with Total Run Time Monitor (S8VS-@@@24B@@/S8VS-@@@24BE@)

Operation Mode

Undervoltage

detected

Maintenance

forecast

18.5 to 20.0 to 27.5 (V)

0.1-V steps

* Factory settings are in reverse

type.

0.5-year steps

0.0 to 0.5 to 5.0 (y)

Press 3 seconds or more or no key

pressed for 30 seconds or more.

Press 3 seconds

or more.

18.5 to 20.0 to 27.5 (V)

0.1-V steps

S8VS

Peak Hold Current Reset

The peak value of the output current (i.e., the peak hold current) can

be reset on the display.

Note: The peak hold current value is not reset in the setting mode.

Undervoltage Alarm Indication

This indicator lights when the output voltage lowers.

Note: 1. When the voltage is restored to the set value or higher and

the Key is pressed at the a01 display to return to the

output current display, the a01 alarm will be cleared and the

normal output display will return.

2. The above displays are for models with a maintenance

forecast monitor (S8VS-@@@24A@@).

Multiple Alarms

When two or more different alarms occur at the same time

*When undervoltage alarm is indicated: Press Key → output

load indication

When the maintenance forecast monitor or overheat alarm is

indicated: Press Key → undervoltage alarm indication

Note: 1. The above displays are for models with a maintenance

forecast monitor (S8VS-@@@24A@@).

Operation mode

Peak hold current

value measurement

starts

Reset

2 seconds (Peak hold current will be displayed

2 seconds after it is reset.)

Key Press 3 seconds or more.

Operation

Mode

Output

current

Peak-hold

current

Maintenance

forecast

monitor

Undervoltage

alarm

Undervoltage occurs.

Output voltage lower limit

*This indicator alternately

displays alarm ( ) and

the output voltage lower

limit.

Operation

Mode

Undervoltage

alarm

Maintenance

forecast

monitor

The indication shifts

alternately in the direction

of the arrow every 2 s.

(See note.)

S8VS

Self-Diagnostics Function

Numbers in the following table indicate the number used in Nomenclature on pages 14 and 17.

Note: 1. External noise is probable as a cause of “---”, “e01”, “e02”, “e03”, “e04”, and “e05” errors.

2. Operation out of the derating curve area, ventilation error, and incorrect mounting direction are probable as a cause of “h\t” error.

3. If the “h\t” error state continues for more than three hours, the maintenance forecast monitor function becomes invalid. The Yrs output

(Maintenance forecast output terminal (Yrs)) will remain OFF (no continuity).

Replace the power supply if this condition occurs even if the output is correct, as internal parts may be deteriorated.

4. The “h\t” error detection function is only for the S8VS-@@@24A@@.

(6) Main display Description Output status Restoration method Setting after

restoration

--- Noise detected in voltage or

current No change Automatic reset. No change

h\t Overheated

Maintenance

forecast output

terminal (Yrs) turns

OFF.

Automatic reset. No change

e01 Undervoltage alarm set value

memory error

Undervoltage

output terminal (DC

LOW) turns OFF. Press and hold the Up Key U (9) or Down

Key D (10) for three seconds and check

the set value of the corresponding point.

The set value must return to the shipment

setting

Shipment setting or

value set in the

setting mode again

e02 Memory error of alarm set value

of maintenance forecast monitor

or total run time monitor

Maintenance

forecast output

terminal (Yrs) turns

OFF or total run

time output terminal

(kh) turns OFF.

e03 Other memory error

Undervoltage

output terminal (DC

LOW) turns OFF.

Maintenance

forecast output

terminal (Yrs) turns

OFF or total run

time output terminal

(kh) turns OFF.

Turn the AC input OFF then ON again.

If the Product is not reset, contact the

dealer. No change

e04,

e05 Hardware error

(S8VS-48024A/B only)

Undervoltage

output terminal (DC

LOW) turns OFF.

Maintenance

forecast output

terminal (Yrs) turns

OFF or total run

time output terminal

(kh) turns OFF.

Turns the AC input OFF then ON again.

If the Product is not reset, contact the

dealer. No change

S8VS

Maintenance Forecast (S8VS-@@@24A@@)

Displays when the maintenance forecast has reached the set value.

Indication and Output

When the Product is purchased, “ful” will be indicated. As

electrolytic capacitors deteriorate, indication changes to “hlf” (Refer

to page 22). “ful” will be indicated for the maintenance forecast

display for approximately one month after the Power Supply is first

turned ON. The accumulated value will then be displayed depending

on the ambient conditions thereafter. (However, the “hlf” indication

may not appear, depending on the usage environment and the set

value for maintenance forecast.)

S8VS-06024A:

After the remaining time to maintenance is reduced to less than two

years, indication automatically changes to a value, which decreases

from “1.5” to “1.0” to “0.5” to “0.0” (year) as the running hours

increase. If the remaining time becomes less than 0.5 year, an alarm

(a02) and “0.0” are indicated alternately.

S8VS-09024A@@/S8VS-12024A@,

S8VS-18024A@/S8VS-24024A@/S8VS-48024A:

If the maintenance forecast setting L (which can be set arbitrarily from

0.0 to 5.0 years in 0.5-year steps) is set to a value larger than two

years, the indication automatically changes to a value (L - 0.5) after

the remaining time to maintenance is reduced to the set years, and an

alarm (a02) and the remaining time are indicated alternately.

If the setting is less than 2.0 years, the indication changes to a value

(1.5) after the remaining time becomes less than two years, and after

the remaining time becomes less than the set time, an alarm (a02)

and the remaining time (L - 0.5) are indicated alternately.

If the alarm (a02) and a numeric value are indicated alternately, a

transistor (maintenance forecast output terminal (Yrs)) will turn OFF

to indicate the need for maintenance. (The transistor turns OFF when

the maintenance forecast time is reached, i.e., there will be no

continuity at the maintenance forecast output terminal.)

Note: 1. The remaining time to maintenance is based on continuous

operation, not including the time when the power supply is

turned OFF.

2. “ful” will be indicated until approximately one month of

time is accumulated to estimate the speed of deterioration

and the output will remain ON (continuity at the

maintenance forecast output terminal (Yrs)).

3. For details on the display, refer to Relationship between

Indicated Values and Output of Set Values under

Maintenance Forecast Monitor Function on page 22.

Operation

Mode

Output

voltage

Maintenance

forecast

monitor

Remaining time

until replacement

The maintenance forecast

has reached the set value.

Output

current

Peak-hold

current

(See note.)

Note: This indicator alternately

displays alarm ( )

and the maintenance

time until replacement.

In the case that the

remaining time is

reduced to smaller

than 0.5 year and an

alarm is issued.

S8VS

Maintenance Forecast Monitor Function

The Power Supply is equipped with electrolytic capacitors.

The electrolyte inside the electrolytic capacitor penetrates the sealing

rubber and evaporates as time passes since it is manufactured, which

causes deterioration of characteristics such as decreasing the

capacitance, etc.

Due to this deterioration of the characteristics of the electrolytic

capacitor, the Power Supply decreases its performance as time

passes.

The maintenance forecast monitor function shows an approximate

period left for maintenance of the Power Supply due to deterioration

of electrolytic capacitors. When the period left for maintenance that

the power supply forecasts reaches the set value, an alarm is

indicated and an output signal is triggered.

Use this function to know the approximate replacement timing of the

Power Supply.

Note: The maintenance forecast monitor function indicates an

approximate period left for maintenance, based on

deterioration of the electrolytic capacitor. It does not predict

failures caused by other reasons.

Relationship between Indicated Values and Output of Set Values

Principle of Operation

The deterioration speed of the electrolytic capacitor varies

considerably according to the ambient temperature. (Generally the

speed follows “Rule of Two for every 10°C”; for every 10°C increase

in temperature the rate of degradation doubles according to

Arrhenius’s equation.) The S8VS-@@@24A@@ monitors the

temperature inside the power supply, and calculates the amount of

deterioration according to the running hours and inside temperature.

Judging by this amount of deterioration, the power supply will give the

alarm indication and output when the period left for maintenance

reaches the set value.

Note: 1. Due to degradation of internal electronic parts, replace the

power supply approximately 15 years after purchase even if

indication and output of maintenance forecast monitor are

not issued.

2. The maintenance forecast is accelerated or decelerated

according to operating conditions. Periodically check

indication.

3. Acceleration or deceleration of the maintenance forecast

may cause the output to repeatedly go ON/OFF.

Only the S8VS-09024A@@, S8VS-12024A@, S8VS-

18024A@, S8VS-24024A@, and S8VS-48024A are

equipped with output.

4. The accuracy of the maintenance forecast function may be

adversely affected by applications in which the AC input is

frequently turned ON/OFF.

Reference Values (15-W to 480-W Models)

Note: The maintenance forecast is the service life (the power

supply’s internal temperature is monitored at all times) of the

internal electrolytic capacitor in actual operating conditions,

and varies according to the customer’s operating conditions.

15 years is taken as the maximum period of the maintenance

forecast.

(L−0.5)

5.0

L=2.5

L=0.5

2.5 2.0 1.5 1.0 0.5 0

Initial capacity

"1.0" is displayed on the main display for the

duration that the maintenance forecast up to

replacement satisfies the condition 1.0 ≤ T < 1.5.

In case of setting L between 2.5 and 5.

Maintenance forecast monitor output

T: Maintenance time

until replacement

The numerical value

decreases with time.

Main displayCapacity of Capacitor

Capacity level

at replacement

Note: This function can be set only on the S8VS-09024A@@, S8VS-12024A@, S8VS-18024A@, S8VS-24024A@, and S8VS-48024A.

L: Maintenance forecast set value (See note.)

0.0 to 5.0, 0.5 steps

Item Value Definition

Reliability

(MTBF)

15 W to 240 W:

135,000 hr min.

480 W:

60,000 hr min.

MTBF stands for Mean Time

Between Failures, which is

calculated according to the

probability of accidental device

failures, and indicates reliability of

devices.

Therefore, it does not necessarily

represent the life of the Product.

Life

expectancy 10 yr min.

The life expectancy indicates

average operating hours under the

ambient temperature of 40°C and a

load rate of 50%. Normally this is

determined by the life expectancy of

the built-in aluminum electrolytic

capacitor.

S8VS

Models with Total Run Time Monitor

(S8VS-@@@24B@@/S8VS-@@@24BE@)

S8VS-06024B

The accumulated value of the operating time of the Power Supply is

displayed as the total run time. 0 (kh) will be displayed initially after

purchase and then the display will advance in 1-kh steps as the

operating time accumulates. The S8VS-06024B, however, does not

have an alarm function (setting, display, or output).

S8VS-09024B@@/S8VS-09024BE@/

S8VS-12024B@/S8VS-12024BE/

S8VS-18024B@/S8VS-18024BE/

S8VS-24024B@/S8VS-24024BE/S8VS-48024B

The display will appear when the set value for the total run time has

been reached.

The accumulated value of the operating time of the Power Supply is

displayed as the total run time. 0 (kh) will be displayed initially after

purchase and then the display will advance in 1-kh steps as the

operating time accumulates. When the total run time reaches the

alarm set value, the alarm (a02) and the total run time will be

displayed alternately and a transistor (total run time output terminal

(kh)) will output the status externally.

(Alarm set value reached = OFF, i.e., no continuity at the total run time

output terminal (kh))

The alarm set value can be changed in the setting mode.

The S8VS-09024BE@, S8VS-12024BE, S8VS-18024BE, and S8VS-

24024BE do not have an alarm output.

Example: Alarm Displays When a Total Run Time Set Value of

88 kh Is Reached

Note: The total run time cannot be reset. To clear the alarm, change

the alarm set value to a value higher than the value displayed

for the total run time.

Time Chart

*Setting is possible for the following models only:

S8VS-09024B@@, S8VS-09024BE@, S8VS-12024B@,

S8VS-12024BE, S8VS-18024B@, S8VS-18024BE,

S8VS-24024B@, S8VS-24024BE, S8VS-48024B

Note: 1. The total run time does not include the time that the Power

Supply is OFF.

2. The total run time measures the total time that power is

being supplied and is not related in any way to deterioration

in the electrolytic capacitor built into the Power Supply or to

the effects of the ambient temperature.

Operation mode

Total run time

Total run time set value reached.

(See note.)

Output

voltage

Output

current

Peak hold

current

Note: The alarm (a02)

and the total run

time will be

displayed

alternately.

Total run time

50 kh

0 kh

AC input

Alarm output

Set value = 50 kh

(See note.)

S8VS

Engineering Data (60-W, 90-W, 120-W, 180-W, 240-W, and 480-W Models)

Derating Curve

Note: 1. Using side mounting bracket for right-side mounting

(excluding 240-W models). UL certification conditions do

not apply if the side mounting bracket is used.

2. Internal parts may occasionally deteriorate or be damaged.

Do not use the Power Supply in areas outside the derating

curve (i.e., the area shown by shading A in the above

graph).

3. If there is a derating problem, use forced air-cooling.

4. When using a 480-W model at an input voltage of 95 VAC

or less, derate the load by at least 80%.

5. DC Inputs for BE Models

If the input voltage is less than 100 VDC, reduce the load

given in the above derating curve by at least the following

factor.

60-W models: 0.9 max.

90-W models: 0.85 max.

120-W/180-W/240-W models: 0.8 max.

Mounting

Note: Improper mounting will interfere with heat dissipation and may

occasionally result in deterioration or damage of internal parts.

It may also result in failure of the maintenance forecast monitor

function. Use the standard mounting method only.

Overload Protection

The Power Supply is provided with an overload protection function

that protects the power supply from possible damage by overcurrent.

When the output current rises above 105% min. of the rated current,

the protection function is triggered, decreasing the output voltage.

When the output current falls within the rated range, the overload

protection function is automatically cleared.

Note: 1. Internal parts may occasionally deteriorate or be damaged

if a short-circuited or overcurrent state continues during

operation.

2. Internal parts may possibly deteriorate or be damaged if the

Power Supply is used for applications with frequent inrush

current or overloading at the load end. Do not use the Power

Supply for such applications.

Peak Output Current (S8VS-48024@ only)

The peak current must satisfy the following conditions.

Input voltage range: 200 to 240 VAC

Peak current value: 30 A max.

Peak current pulse width: 2 s max.

Cycle: 60 s min.

Note: 1. Two seconds after the peak current is reached, the peak

current limiting function operates to stop the peak current

flow.

2. It takes 60 seconds for the peak current to be able to flow

again.

3. The peak current limiting function prevents the peak current

from flowing at 100 to 120 VAC.

Overvoltage Protection

Consider the possibility of an overvoltage and design the system so

that the load will not be subjected to an excessive voltage even if the

feedback circuit in the Power Supply fails. If an excessive voltage that

is approximately 130% of the rated voltage (but approximately 110%

of the rated voltage for the S8VS-09024@@@S) or more is output, the

output voltage is shut OFF. Reset the input power by turning it OFF

for at least three minutes and then turning it back ON again.

Note: Do not turn ON the power again until the cause of the

overvoltage has been removed.

Inrush Current, Startup Time, Output Hold Time

−20 −10 0 10 20 30 40 50 60 70 80

120

100

Load (%)

Ambient temperature (°C)

See note 1.

Upper Upper

Standard mounting Face-up mounting

Correct Incorrect

050100 0 50 100

Output current (%)

Output voltage (V)

Output current (%)

Output voltage (V)

Intermittent operation

60-W/90-W Models 120-W/180-W/240-W/480-W Models

The values shown in the above diagrams are for reference only.

Peak current limit

Output current

0 A

Overcurrent

protectionpoint

60 s min.

2 s Peak current

condition

+15%

−10%

0 V

+30%

(approx.)

Overvoltage protection

operating

Variable range

Rated output

voltage

Output voltage (V)

The values shown in the above diagram is for reference only.

90%

96.5%

Startup time (1,000 ms max.)

AC input

voltage

AC input

current

Output

voltage

Inrush current on input application

Input OFF

Input ON

Hold time

(20 ms min.)

S8VS

Undervoltage Alarm Function (Indication and

Output) (S8VS-@@@24A@@/S8VS-@@@24B@@/

S8VS-@@@24BE@ Only)

When output voltage drop is detected, an alarm (a01) and lowest

output voltage value are indicated alternately. The preset value of

detection voltage can be changed in the setting mode.

(From 18.5 to 27.5 V in 0.1-V steps. The value is fixed at 20.0 V for

the S8VS-06024A/S8VS-06024B.)

Further, an output (undervoltage output terminal (DC LOW)) to an

external device is given from the transistor to notify of the error

(excluding S8VS-06024A/S8VS-06024B/S8VS-@@@24BE@).

(Output voltage drop = OFF, i.e., no continuity at the undervoltage

output terminal (DC LOW).)

Example: Outputting an Alarm When the Voltage Output by the

S8VS-09024A@@ Drops to the Set Value (19.0 V) or Lower

Note: 1. Operation begins after about three seconds since the AC

power is supplied.

2. The alarm is not indicated in the setting mode.

3. Press the (Mode Key (8)) after the output voltage is

restored, to reset alarm indication.

4. The undervoltage alarm function may also operate when an

interruption in AC input is not restored within 20 ms.

5. The undervoltage alarm function monitors the output

terminal voltage of the Power Supply. To check the voltage

accurately, measure the voltage at the load end.

Note: Operation begins after about three seconds since the AC

power is supplied.

In the case that the

output voltage drops

below the set value (19.0 V)

and an alarm is issued

AC input

Output

voltage

Undervoltage

output

Main display Voltage indication

Detection value

of Undervoltage

alarm

Operation

mode Lowest value of

output voltage

S8VS

Dimensions

Power Supplies with Screw Terminal Blocks

Note: All units are in millimeters unless otherwise indicated.

Note: The illustration is the S8VS-03024 model.

Note: The illustration is the S8VS-06024A model.

Note: The illustration is the S8VS-12024A model.

Note: The illustration is the S8VS-18024A model.

4.8

(Sliding: 10 max.)

4.8

(Sliding: 10 max.)

35.2

96.4 22.5

Rail stopper

Five, M3.5 terminal screws

with square washers

S8VS-015@@ (15 W)

S8VS-030@@ (30 W)

97 11.3

35.4

108.3

140

74 95

Five, M4 terminal screws

with square washers

Rail stopper

4.5

(Sliding: 15 max.)

S8VS-06024 (60 W)

S8VS-06024A (60 W)

S8VS-06024B (60 W)

110.5 10.8

35.4

121.3

94 115

Five, M4 terminal screws

with square washers

Rail stopper

Screwless block (2.5-mm pitches)

4.5

(Sliding: 15 max.)

S8VS-09024 (90 W) /S8VS-09024S (90 W) /S8VS-12024 (120 W)

S8VS-09024A@ (90 W) /S8VS-09024A@S (90 W) /S8VS-12024A@ (120 W)

S8VS-09024B@ (90 W) /S8VS-09024B@S (90 W) /S8VS-12024B@ (120 W)

S8VS-09024BE (90 W) /S8VS-09024BES (90 W) /S8VS-12024BE (120 W)

94 115

75 4.5

125.3

120.3

35.4

Rail stopper

Screwless block (2.5-mm pitches) (Sliding: 15 max.)

Seven, M4 terminal screws

with square washers

S8VS-18024 (180 W)

S8VS-18024A@ (180 W)

S8VS-18024B@ (180 W)

S8VS-18024BE (180 W)

S8VS

Note: The illustration shows the S8VS-24024A model.

Note: The illustration shows the S8VS-48024A model.

Power Supplies with Screwless Terminal Blocks

Note: The illustration shows the S8VS-06024-F model.

Note: The illustration shows the S8VS-12024-F model.

125.3

120.3

35.4

100

115

Seven, M4 terminal screws

with square washers

Rail stopper 4.5 (Sliding: 15 max.)

Rail stopper

Screwless block (2.5-mm pitches)

S8VS-24024 (240 W)

S8VS-24024A@ (240 W)

S8VS-24024B@ (240 W)

S8VS-24024BE (240 W)

S8VS-48024 (480 W)

S8VS-48024A (480 W)

S8VS-48024B (480 W)

Rail stopper

Nine, M4 terminal screws with square washers

4.5 (Sliding: 15 max.)

Rail stopper

123.8

127.2

35.4 93

115 115

150

Screwless block (2.5-mm pitches)

107.3

97.1 10.2

35.4 9577.4

40 4.5 (Sliding: 15 max.)

Rail stopper

S8VS-06024-F (60 W)

S8VS-06024A-F (60 W)

S8VS-06024B-F (60 W)

120.3

110.3

115

35.4 97.3

4.5 (Sliding: 15 max.)

Rail stopper

S8VS-09024-F (90 W) /S8VS-09024S-F (90 W) /S8VS-12024-F (120 W)

S8VS-09024A@-F (90 W) /S8VS-09024A@S-F (90 W ) /S8VS-12024A@-F (120 W)

S8VS-09024B@-F (90 W) /S8VS-09024B@S-F (90 W) /S8VS-12024B@-F (120 W)

S8VS-09024BE-F (90 W) /S8VS-09024BES-F (90 W) /S8VS-12024BE-F (120 W)

S8VS

Note: The illustration shows the S8VS-18024-F model.

Note: The illustration shows the S8VS-24024-F model.

Note: The illustration shows the S8VS-48024-F model.

7.7

124

116.3

115

35.4 97.3

4.5 (Sliding: 15 max.)

Rail stopper

S8VS-18024-F (180 W)

S8VS-18024A@-F (180 W)

S8VS-18024B@-F (180 W)

S8VS-18024BE-F (180 W)

100

6.7

124.3

117.6

115

35.4 97.3

50 4.5 (Sliding: 15 max.)

Rail stopperRail stopper

S8VS-24024-F (240 W)

S8VS-24024A@-F (240 W)

S8VS-24024B@-F (240 W)

S8VS-24024BE-F (240 W)

150

122.9

127.2

35.4 115

70 4.5 (Sliding: 15 max.)

Rail stopper

96.3

S8VS-48024-F (480 W)

S8VS-48024A-F (480 W)

S8VS-48024B-F (480 W)

S8VS

DIN Rail (Order Separately)

Note: All units are in millimeters unless otherwise indicated.

Mounting Rail (Material: Aluminum) PFP-100N

PFP-50N

Mounting Rail (Material: Aluminum) PFP-100N2

End Plate PFP-M

Note: If there is a possibility that the Unit will be subject to vibration or shock, use a steel DIN Rail. Otherwise, metallic filings may result from

aluminum abrasion.

4.5

15 25 25

10 10

1,000 (500) *

25 25 15(5) *

35±0.3

7.3±0.15

27±0.15

* Values in parentheses are for the PFP-50N.

4.5

15 25 25

10 10

1,000

25 25 15 1 1.5

29.2242735±0.3

1.3

4.8

35.5 35.5

1.8

6.2

11.5

M4 spring washer

M4×8 pan-

head screw

S8VS

Mounting Brackets

Note: Brackets cannot be used for 480-W models.

*Two required to mount a 240-W model.

Name Model

Side-mounting Bracket (for 15- and 30-W models) S82Y-VS30P

Side-mounting Bracket (for 60-, 90-, and 120-W models) S82Y-VS10S

Side-mounting Bracket (for 180-W models) S82Y-VS15S

Side-mounting Bracket (for 240-W models) S82Y-VS20S

Front-mounting Bracket (for 60-, 90-, 120-, 180-, and 240-W models) *S82Y-VS10F

Type Model Dimensions Appearance

Side-mounting Bracket

(For 15-, 30-W models) S82Y-VS30P

Side-mounting Bracket

(For 60-, 90-, 120-W

models)

S82Y-VS10S

Side-mounting Bracket

(For 180-W models) S82Y-VS15S

Side-mounting Bracket

(For 240-W models) S82Y-VS20S

Front-mounting Bracket

(For 60-, 90-, 120-, 180-,

and 240-W models)

S82Y-VS10F

7.1

3.5

0.5

15 15

93.6

109.4±0.1

85.4

22.5

34 28

t = 0.8

3.5 dia.

t = 2.0

80 60

±0.1

4.5 dia.

±0.1

Left-side mounting Right-side mounting

t = 2.0

89 78

55±0.1

47.5

4.5 dia.±0.1

80 60±0.1

Left-side mounting

*Right-side mounting also possible.

60±0.1

55±0.1 13

114

4.5 dia.±0.1

t = 2.0

Left-side mounting

*Right-side mounting also possible.

±0.1

4.5 dia.±0.1

7.3

(For 60-, 90-, 120-,

180-W types)

(For 240-W type)

*Use two S82Y-VS10F

brackets for the 240-W type.

S8VS

Safety Precautions

!CAUTION

Minor electric shock, fire, or Product failure may

occasionally occur. Do not disassemble, modify, or

repair the Product or touch the interior of the

Product.

Minor burns may occasionally occur. Do not touch

the Product while power is being supplied or

immediately after power is turned OFF.

Fire may occasionally occur. Tighten terminal screws

to the specified torque (15- and 30-W models: 0.8 to

1.0 N·m/60-, 90-,120-, 180-, 240-, and 480-W models:

1.08 N·m).

Minor injury due to electric shock may occasionally

occur. Do not touch the terminals while power is

being supplied. Always close the terminal cover after

wiring.

Minor electric shock, fire, or Product failure may

occasionally occur. Do not allow any pieces of metal

or conductors or any clippings or cuttings resulting

from installation work to enter the Product.

Mounting

•Take adequate measures to ensure proper heat dissipation to

increase the long-term reliability of the Product. Be sure to allow

convection in the atmosphere around devices when mounting. Do

not use in locations where the ambient temperature exceeds the

range of the derating curve.

•When cutting out holes for mounting, make sure that cuttings do

not enter the interior of the Products.

15-W and 30-W Models

•Improper mounting will interfere with heat dissipation and may

occasionally result in deterioration or damage of internal parts. Use

the Product within the derating curve for the mounting direction that

is used.

•Use a mounting bracket when the Product is mounted facing

horizontally.

•Heat dissipation will be adversely affected. When the Product is

mounted facing horizontally, always place the side with the label

facing upward.

•Always provide a space of 20 mm even when mounting horizontal

or facing horizontal. If a space of 20 mm is not available, reduce

the temperatures given in the derating curve on page 14 by 5°C

and provide a space of at least 10 mm.

60-W, 90-W, 120-W, 180-W, 240-W, and 480-W Models

•Improper mounting will interfere with heat dissipation and may

occasionally result in deterioration or damage of internal parts. Use

the standard mounting method only.

•The internal parts may occasionally deteriorate and be broken due

to adverse heat radiation. Do not loosen the screw on the side face

of the main body.

Wiring

•Connect the ground completely. A protective earthing terminal

stipulated in safety standards is used. Electric shock or malfunction

may occur if the ground is not connected completely.

•Minor fire may possibly occur. Ensure that input and output

terminals are wired correctly.

•Do not apply more than 100-N force to the terminal block when

tightening it.

•Be sure to remove the sheet covering the Product for machining

before power-ON so that it does not interfere with heat dissipation.

•When wiring a screwless terminal block, do not insert more than

one wire into a single terminal.

•When using a screwless terminal block, connect or disconnect the

I/O wire to each terminal while inserting an appropriate tool, such

as a flat-blade screwdriver, into the tool insertion hole. Make sure

that the wire is securely connected to the terminal after wiring. Do

not insert wires into the tool insertion holes.

If a wire is not inserted far enough or if it is loose, electric shock,

fire, or equipment failure may occur. Strip the wires according to

specifications. Insert an appropriate tool, such as a flat-blade

screwdriver, into the tool insertion hole, insert the wire until the

stripped portion is no longer visible, and then remove the tool.

Make sure that the wires are securely connected to the terminal

block after wiring. Never insert wires into the tool insertion holes.

•Use the following material for the wires to be connected to the

S8VS to prevent smoking or ignition caused by abnormal loads.

Recommended Wire Type

15-W and 30-W Models

60-W, 90-W, 120-W, 180-W, 240-W, and 480-W Models

Precautions for Safe Use

*1. Convection of air

*2. 20 mm min.

Model Stranded wire Solid wire

S8VS-03005 AWG18 to 14

(0.9 to 2.0 mm2)AWG18 to 16

(0.9 to 1.1 mm2)

Other models AWG20 to 14

(0.5 to 2.0 mm2)AWG20 to 16

(0.5 to 1.1 mm2)

Model

Recommended wire size

Input

terminals

Output

terminals

Alarm output

terminals

S8VS-06024@

AWG14 to 20

(Cross section:

0.517 to

2.081 mm2)

AWG14 to 20

(Cross section:

0.517 to

2.081 mm2)

---

S8VS-

09024@@@@

AWG18 to 28

(Cross

section: 0.081

to 0.823 mm2)

(Wires to be

stripped:

9 to 10 mm)

S8VS-

12024@@@

AWG14 to 18

(Cross section:

0.823 to

2.081 mm2)

S8VS-

18024@@@

AWG14 to 16

(Cross section:

1.309 to

2.081 mm2)

S8VS-

24024@@@ AWG14

(Cross section:

2.081 mm2)

S8VS-48024@

AWG 14 to 16

(Cross section:

1,309 to

2,081 mm2)

Tool insertion hole

3.7 mm

Wire hole

S8VS

•Strip I/O wires for 11 mm when using a screwless terminal block.

*The rated current for output terminals is 10 A per terminal. Be sure

to use multiple terminals simultaneously for current that exceeds

the terminal rating. When applying a current of 10 A or more, use at

least two terminals each for the positive and negative wires.

Installation Environment

•Do not use the Power Supply in locations subject to shocks or

vibrations. In particular, install the Power Supply as far away as

possible from contactors or other devices that are a vibration

source.

•Install the Power Supply well away from any sources of strong,

high-frequency noise and surge.

Operating Life

•The life of a Power Supply is determined by the life of the

electrolytic capacitors used inside. Here, Arrhenius Law applies,

i.e., the life will be cut in half for each rise of 10°C or the life will be

doubled for each drop of 10°C. The life of the Power Supply can

thus be increased by reducing its internal temperature.

Ambient Operating and Storage Environments

•Store the Power Supply at a temperature of −25 to 65°C and a

humidity of 25% to 90%.

•Do not use the Power Supply in areas outside the derating curve

otherwise, internal parts may occasionally deteriorate or be

damaged.

•Use the Power Supply at a humidity of 25% to 85%.

•Do not use the Power Supply in locations subject to direct sunlight.

•Do not use locations where liquids, foreign matter, or corrosive

gases may enter the interior of Products.

S8VS-@@@24A@@ Models only

Satisfy the following conditions when storing the Power Supply for

long periods of time to maintain its remaining service life function.

When storing for more than three months, store within an ambient

temperature range of −25 to +30°C and the humidity range of 25% to

70%.

Periodic Check for Models with Indication

Monitor Except 60-W Models

It may take from several years to more than 10 years under general

operating conditions for the power supply to output the maintenance

forecast monitor alarm (S8VS-@@@24A@@). The total run time

monitor (S8VS-@@@24B@@/S8VS-@@@24BE@) may be a similar

number of years as the maintenance forecast monitor according to

some settings. During operation over an extended period of time,

periodically check if the maintenance forecast monitor output (Yrs) or

total run time monitor output (kh) is correctly functioning by the

following procedure.

1. Select the operation mode.

2. Check that the output (Yrs/kh) is turned ON (with continuity).

3. In the operation mode, press and hold the Down Key D (10) and

the Mode Key M (8) simultaneously for at least three seconds.

The main display (6) changes to “a02.”

An inactive output (Yrs/kh) (no continuity) in the “a02” indication

indicates the correct function.

4. Release keys to return to the regular state.

Note: DC output stays ON during the periodical check.

Overcurrent Protection

•Internal parts may possibly deteriorate or be damaged if a

short-circuited or overcurrent state continues during operation.

•Internal parts may possibly deteriorate or be damaged if the Power

Supply is used for applications with frequent inrush current or

overloading at the load end. Do not use the Power Supply for such

applications.

Alarm Output for Models with Indication Monitor

Except 60-W and BE Models

When using the alarm output, sufficiently consider the maximum

ratings, residual voltage, and leakage current.

Transistor output: Sinking for S8VS-24A@/@@@24B@ models

Sourcing for S8VS-@@@24AP@/@@@24BP@

models

Sinking/Sourcing for S8VS-48024A/B models

30 VDC max., 50 mA max.

ON residually voltage:2 V max.

OFF leakage current: 0.1 mA max.

Dielectric Strength Test

If a high voltage is applied between an input and the case (FG), it will

pass though the LC of the built-in noise filter and energy will be stored.

If the high voltages used for dielectric strength testing are turned ON

and OFF with a switch, timer, or similar device, impulse voltage will

be generated when the voltage is turned OFF and internal parts may

possibly be damaged. To prevent the generation of impulse voltages,

reduce the applied voltage slowly with a variable resistor on the test

device or turn the voltage ON and OFF at the zero-cross point.

Inrush Current

When two or more Power Supplies are connected to the same input,

the total current is the sum of the currents for each Supply. Select

fuses and circuit breakers giving sufficient consideration to the fusing

or operating characteristics so that fuses will not burn and breakers

will not break due to inrush current.

(COMMON)

(Yrs/kh)

(DC LOW)

60-, 90-, 120-,

180-, 240-W

Models

13 11

(Yrs/kh) (DC LOW)

480-W Models

S8VS

Output Voltage Adjuster (V.ADJ)

•The output voltage adjuster (V.ADJ) may possibly be damaged if it

is turned with unnecessary force. Do not turn the adjuster with

excessive force.

•After completing output voltage adjustment, be sure that the output

capacity or output current does not exceed the rated output

capacity or rated output current.

15-W, 30-W Models

•If the output voltage is set to a value less than −10%, the

undervoltage alarm function may operate.

60-W, 90-W, 120-W, 180-W, 240-W, and 480-W Models

•If the detection voltage of the undervoltage alarm function is at the

factory setting and the output voltage is set to a value of 20 V or

less, the undervoltage alarm function may operate.

DIN Rail Mounting

To mount the Block on a DIN Rail, hook portion (A) of the Block onto

the rail and press the Block in direction (B).

To dismount the Block, pull down portion (C) with a flat-blade

screwdriver and pull out the Block.

Series Operation

(24-V Model)

Two power supplies can be connected in series.

Note: 1. The diode is connected as shown in the figure. If the load is

short-circuited, a reverse voltage will be generated inside

the Power Supply. If this occurs the Power Supply may

possibly deteriorate or be damaged. Always connect a

diode as shown in the figure.

Select a diode having the following ratings.

2. Although Products having different specifications can be

connected in series, the current flowing through the load

must not exceed the smaller rated output current.

3. Serial operation is not possible with 5-V and 12-V models.

Parallel Operation

The Product is not designed for parallel operation.

In Case There Is No Output Voltage

The possible cause for no output voltage may be that the overcurrent

or overvoltage protection has operated. The internal protection may

operate if a large amount of surge voltage such as a lightening surge

occurs while turning ON the power supply.

In case there is no output voltage, please check the following points

before contacting us:

•Checking overload protected status:

Check whether the load is in overload status or is short-circuited.

Remove wires to load when checking.

•Checking overvoltage or internal protection (except for 15-W

models):

Turn the power supply OFF once, and leave it OFF for at least

3 minutes. Then turn it ON again to see if this clears the condition.

Buzzing Noise When the Input Is Turned ON

(120-W, 180-W, 240-W, and 480-W Models)

A harmonic current suppression circuit is built into the Power Supply.

This circuit can create noise when the input is turned ON, but it will

last only until the internal circuits stabilize and does not indicate any

problem in the Product.

Type Schottky Barrier diode

Dielectric strength (VRRM) Twice the rated output voltage or above

Forward current (IF) Twice the rated output current or above

(B)

(A)

(C)

30 mm min.

Track stopper

−V

Correct

AC (L)

AC (N)

AC (L)

AC (N)

−V

Incorrect

AC (L)

AC (N)

AC (L)

AC (N)

In the interest of product improvement, specifications are subject to change without notice.

ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.

To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.

Read and Understand This Catalog

Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or

comments.

Warranty and Limitations of Liability

WARRANTY

OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified)

from date of sale by OMRON.

OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR

FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS. ANY BUYER OR USER ACKNOWLEDGES THAT THE BUYER OR USER ALONE HAS

DETERMINED THAT THE PRODUCTS WILL SUITABLY MEET THE REQUIREMENTS OF THEIR INTENDED USE. OMRON DISCLAIMS ALL OTHER

WARRANTIES, EXPRESS OR IMPLIED.

LIMITATIONS OF LIABILITY

OMRON SHALL NOT BE RESPONSIBLE FOR SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR COMMERCIAL LOSS

IN ANY WAY CONNECTED WITH THE PRODUCTS, WHETHER SUCH CLAIM IS BASED ON CONTRACT, WARRANTY, NEGLIGENCE, OR STRICT

LIABILITY.

In no event shall the responsibility of OMRON for any act exceed the individual price of the product on which liability is asserted.

IN NO EVENT SHALL OMRON BE RESPONSIBLE FOR WARRANTY, REPAIR, OR OTHER CLAIMS REGARDING THE PRODUCTS UNLESS

OMRON'S ANALYSIS CONFIRMS THAT THE PRODUCTS WERE PROPERLY HANDLED, STORED, INSTALLED, AND MAINTAINED AND NOT

SUBJECT TO CONTAMINATION, ABUSE, MISUSE, OR INAPPROPRIATE MODIFICATION OR REPAIR.

Application Considerations

SUITABILITY FOR USE

OMRON shall not be responsible for conformity with any standards, codes, or regulations that apply to the combination of products in the customer's

application or use of the products.

At the customer's request, OMRON will provide applicable third party certification documents identifying ratings and limitations of use that apply to the

products. This information by itself is not sufficient for a complete determination of the suitability of the products in combination with the end product,

machine, system, or other application or use.

The following are some examples of applications for which particular attention must be given. This is not intended to be an exhaustive list of all possible

uses of the products, nor is it intended to imply that the uses listed may be suitable for the products:

•

Outdoor use, uses involving potential chemical contamination or electrical interference, or conditions or uses not described in this catalog.

•

Nuclear energy control systems, combustion systems, railroad systems, aviation systems, medical equipment, amusement machines, vehicles,

safety equipment, and installations subject to separate industry or government regulations.

•

Systems, machines, and equipment that could present a risk to life or property.

Please know and observe all prohibitions of use applicable to the products.

NEVER USE THE PRODUCTS FOR AN APPLICATION INVOLVING SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE

SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS, AND THAT THE OMRON PRODUCTS ARE PROPERLY RATED AND

INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL EQUIPMENT OR SYSTEM.

PROGRAMMABLE PRODUCTS

OMRON shall not be responsible for the user's programming of a programmable product, or any consequence thereof.

Disclaimers

CHANGE IN SPECIFICATIONS

Product specifications and accessories may be changed at any time based on improvements and other reasons.

It is our practice to change model numbers when published ratings or features are changed, or when significant construction changes are made.

However, some specifications of the products may be changed without any notice. When in doubt, special model numbers may be assigned to fix or

establish key specifications for your application on your request. Please consult with your OMRON representative at any time to confirm actual

specifications of purchased products.

DIMENSIONS AND WEIGHTS

Dimensions and weights are nominal and are not to be used for manufacturing purposes, even when tolerances are shown.

PERFORMANCE DATA

Performance data given in this catalog is provided as a guide for the user in determining suitability and does not constitute a warranty. It may represent the

result of OMRON’s test conditions, and the users must correlate it to actual application requirements. Actual performance is subject to the OMRON

Warranty and Limitations of Liability.

ERRORS AND OMISSIONS

The information in this document has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical,

typographical, or proofreading errors, or omissions.

2011.1

In the interest of product improvement, specifications are subject to change without notice.

OMRON Corporation

Industrial Automation Company

http://www.ia.omron.com/