Transient Voltage Suppression Diodes Axial Leaded - 5000W > 5KP series 5KP Series RoHS Description Uni-directional The 5KP Series is designed specifically to protect sensitive electronic equipment from voltage transients induced by lightning and other transient voltage events. * Typical maximum temperature coefficient VBR = 0.1% x VBR@25C x T Agency Approvals AGENCY AGENCY FILE NUMBER E128662/E230531 Maximum Ratings and Thermal Characteristics (TA=25C unless otherwise noted) Parameter Symbol Value Unit PPPM 5000 W PD 8.0 W IFSM 400 A VF 3.5/5.0 V TJ , TSTG -55 to 175 C Typical Thermal Resistance Junction to Lead RuJL 8.0 C/W Typical Thermal Resistance Junction to Ambient RuJA 40 C/W Peak Pulse Power Dissipation by 10x1000s Test Waveform (Fig.2) (Note 1) Steady State Power Dissipation on Inifinite Heat Sink at TL=75C (Fig. 6) Peak Forward Surge Current, 8.3ms Single Half Sine Wave Unidirectional Only (Note 2) Maximum Instantaneous Forward Voltage at 100A for Unidirectional Only (Note 3) Operating Junction and Storage Temperature Range Applications Notes: 1. Non-repetitive current pulse , per Fig. 4 and derated above TA = 25C per Fig. 3. 2. Measured on 8.3ms single half sine wave or equivalent square wave, duty cycle=4 per minute maximum. _ 200V and VF<5.0V for devices of VBR > _ 201V. 3. VF<3.5V for devices of VBR < Functional Diagram Bi-directional Cathode Anode Uni-directional (c) 2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/04/13 * Glass passivated chip junction in P600 package * 5000W peak pulse capability at 10x1000s waveform, repetition rate (duty cycles):0.01% * Fast response time: typically less than 1.0ps from 0 Volts to BV min * Excellent clamping capability * Typical failure mode is short from over-specified voltage or current * Whisker test is conducted based on JEDEC JESD201A per its table 4a and 4c * IEC-61000-4-2 ESD 15kV(Air), 8kV (Contact) * ESD protection of data lines in accordance with IEC 61000-4-2 (IEC801-2) * EFT protection of data lines in accordance with IEC 61000-4-4 (IEC801-4) * Low incremental surge resistance * Typical IR less than 2A above 12V * High temperature soldering guaranteed: 260C/40 seconds / 0.375", (9.5mm) lead length, 5 lbs., (2.3kg) tension * Plastic package has underwriters laboratory flammability classification 94V-O * Matte tin lead-free plated * Halogen free and RoHS compliant TVS devices are ideal for the protection of I/O interfaces, VCC bus and other vulnerable circuits used in telecom, computer, industrial and consumer electronic applications. 5KP Series Features Bi-directional Transient Voltage Suppression Diodes Axial Leaded - 5000W > 5KP series Electrical Characteristics.(TA=25C unless otherwise noted) Part Number (Uni) Part Number (Bi) Reverse Stand off Voltage VR (Volts) 5KP5.0A 5KP6.0A 5KP6.5A 5KP7.0A 5KP7.5A 5KP8.0A 5KP8.5A 5KP9.0A 5KP10A 5KP11A 5KP12A 5KP13A 5KP14A 5KP15A 5KP16A 5KP17A 5KP18A 5KP20A 5KP22A 5KP24A 5KP26A 5KP28A 5KP30A 5KP33A 5KP36A 5KP40A 5KP43A 5KP45A 5KP48A 5KP51A 5KP54A 5KP58A 5KP60A 5KP64A 5KP70A 5KP75A 5KP78A 5KP85A 5KP90A 5KP100A 5KP110A 5KP120A 5KP130A 5KP150A 5KP160A 5KP170A 5KP180A 5KP190A 5KP200A 5KP210A 5KP220A 5KP250A 5KP5.0CA 5KP6.0CA 5KP6.5CA 5KP7.0CA 5KP7.5CA 5KP8.0CA 5KP8.5CA 5KP9.0CA 5KP10CA 5KP11CA 5KP12CA 5KP13CA 5KP14CA 5KP15CA 5KP16CA 5KP17CA 5KP18CA 5KP20CA 5KP22CA 5KP24CA 5KP26CA 5KP28CA 5KP30CA 5KP33CA 5KP36CA 5KP40CA 5KP43CA 5KP45CA 5KP48CA 5KP51CA 5KP54CA 5KP58CA 5KP60CA 5KP64CA 5KP70CA 5KP75CA 5KP78CA 5KP85CA 5KP90CA 5KP100CA 5KP110CA 5KP120CA 5KP130CA 5KP150CA 5KP160CA 5KP170CA 5KP180CA 5KP190CA 5KP200CA 5KP210CA 5KP220CA 5KP250CA 5.0 6.0 6.5 7.0 7.5 8.0 8.5 9.0 10.0 11.0 12.0 13.0 14.0 15.0 16.0 17.0 18.0 20.0 22.0 24.0 26.0 28.0 30.0 33.0 36.0 40.0 43.0 45.0 48.0 51.0 54.0 58.0 60.0 64.0 70.0 75.0 78.0 85.0 90.0 100.0 110.0 120.0 130.0 150.0 160.0 170.0 180.0 190.0 200.0 210.0 220.0 250.0 Breakdown Voltage VBR (Volts) @ IT MIN MAX Test Current IT (mA) 6.40 6.67 7.22 7.78 8.33 8.89 9.44 10.00 11.10 12.20 13.30 14.40 15.60 16.70 17.80 18.90 20.00 22.20 24.00 26.70 28.90 31.10 33.30 36.70 40.00 44.40 47.80 50.00 53.30 56.70 60.00 64.40 66.70 71.10 77.80 83.30 86.70 94.40 100.00 110.00 122.00 133.00 144.00 167.00 178.00 189.00 200.00 211.00 222.00 233.00 244.00 277.00 7.00 7.37 7.98 8.60 9.21 9.83 10.40 11.10 12.30 13.50 14.70 15.90 17.20 18.50 19.70 20.90 22.10 24.50 26.90 29.50 31.90 34.40 36.80 40.60 44.20 49.10 52.80 55.30 58.90 62.70 66.30 71.20 73.70 78.60 86.00 92.10 95.80 104.00 111.00 123.00 135.00 147.00 159.00 185.00 197.00 209.00 221.00 233.00 246.00 258.00 270.00 306.00 50 50 50 50 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 5 Maximum Clamping Voltage VC @ IPP (V) Maximum Peak Pulse Current IPP (A) Maximum Reverse Leakage IR @ VR ( A) 9.2 10.3 11.2 12.0 12.9 13.6 14.4 15.4 17.0 18.2 19.9 21.5 23.2 24.4 26.0 27.6 29.2 32.4 35.5 38.9 42.1 45.4 48.4 53.3 58.1 64.5 69.4 72.7 77.4 82.4 87.1 93.6 96.8 103.0 113.0 121.0 126.0 137.0 146.0 162.0 177.0 193.0 209.0 243.0 259.0 275.0 292.0 310.0 329.2 349.5 371.1 425.0 554.3 495.1 455.4 425.0 395.3 375.0 354.2 331.2 300.0 280.2 256.3 237.2 219.8 209.0 196.2 184.8 174.7 157.4 143.7 131.1 121.1 112.3 105.4 95.7 87.8 79.1 73.5 70.2 65.9 61.9 58.6 54.5 52.7 49.5 45.1 42.1 40.5 37.2 34.9 31.5 28.8 26.4 24.4 21.0 19.7 18.5 17.5 16.5 15.5 14.6 13.7 12.0 5000 5000 2000 1000 250 150 50 20 15 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 Agency Approval X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X For bidirectional type having VR of 10 volts and less, the IR limit is double. For parts without A , the VBR is + 10% and VC is 5% higher than with A parts (c) 2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/04/13 Transient Voltage Suppression Diodes Axial Leaded - 5000W > 5KP series I-V Curve Characteristics Bi-directional Uni-directional Ipp Vc VBR VR IR VF IT IT IR Vc VBR VR V IR IT VR VBR Vc V Ipp Ipp 5KP Series PPPM Peak Pulse Power Dissipation -- Max power dissipation VR Stand-off Voltage -- Maximum voltage that can be applied to the TVS without operation VBR Breakdown Voltage -- Maximum current that flows though the TVS at a specified test current (IT) VC Clamping Voltage -- Peak voltage measured across the suppressor at a specified Ippm (peak impulse current) IR Reverse Leakage Current -- Current measured at VR VF Forward Voltage Drop for Uni-directional Ratings and Characteristic Curves (TA=25C unless otherwise noted) Figure 1 - TVS Transients Clamping Waveform Figure 2 - Peak Pulse Power Rating Curve Voltage Transients PPPM - Peak Pulse Power (kW) 100 Voltage or Current Voltage Across TVS Current Through TVS Non-repetitive pulse waveform shown in Fig.3 TA=25C 10 1 0.1 0.1s 1.0s 10s 100s 1.0ms 10ms td - Pulse Width (sec.) Time continues on next page. (c) 2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/04/13 Transient Voltage Suppression Diodes Axial Leaded - 5000W > 5KP series Ratings and Characteristic Curves (TA=25C unless otherwise noted) (Continued) Figure 4 - Pulse Waveform Figure 3 - Pulse Derating Curve 150 IPPM- Peak Pulse Current, % IRSM Peak Pulse Power (kW) 100 75 50 25 0 0 25 50 75 100 125 150 175 200 tr=10sec Half Value IPPM IPPM ( ) 2 50 0 Steady State Power Dissipation (W) Uni-directional V=0V Cj (pF) Uni-directional @ VR 1000 Bi-directional @ VR Tj=25C f=1.0MHz Vsig=50mVp-p 10.0 100.0 1.0 0 2.0 3.0 4.0 9 Bi-directional V=0V 1 1.0 td Figure 6 - Steady State Power Derating Curve 100000 10 10/1000sec. Waveform as defined by R.E.A t-Time (ms) Figure 5 - Typical Junction Capacitance 100 Peak Value IPPM 100 TA - Ambient Temperature (C) 10000 TJ=25C Pulse Width(td) is defined as the point where the peak current decays to 50% of IPPM 1000.0 VBR - Reverse Breakdown Voltage (V) 8 7 6 5 4 3 L = 0.375" (9.5mm) Lead Lengths 2 1 0 0 25 50 75 100 125 150 175 200 TL - Lead Temperature(C) Figure 7 - Maximum Non-Repetitive Peak Forward Surge Current IFSM, Peak Forward Surge Current (A) 450 400 350 300 250 200 150 100 50 0 1 10 100 Number of Cycles at 60 Hz (c) 2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/04/13 Transient Voltage Suppression Diodes Axial Leaded - 5000W > 5KP series Soldering Parameters Lead-free assembly Reflow Condition - Temperature Max (Ts(max)) 200C - Time (min to max) (ts) 60 - 180 secs Average ramp up rate (Liquidus Temp (TL) to peak 3C/second max tL Critical Zone TL to TP Ts(max) Ramp-down Ts(min) ts Preheat 3C/second max 25C - Temperature (TL) (Liquidus) 217C - Time (min to max) (ts) 60 - 150 seconds t 25C to Peak Time (t) Peak Temperature (TP) 260+0/-5 C Time within 5C of actual peak Temperature (tp) 20 - 40 seconds Flow/Wave Soldering (Solder Dipping) Ramp-down Rate 6C/second max Peak Temperature : 265C Time 25C to peak Temperature (TP) 8 minutes Max. Dipping Time : 10 seconds Do not exceed 280C Soldering : 1 time Physical Specifications 5KP Series TS(max) to TL - Ramp-up Rate Reflow TL Temperature (T) Pre Heat Ramp-up 150C - Temperature Min (Ts(min)) tp TP Environmental Specifications Weight 0.07oz., 2.1g Temperature Cycle JESD22-A104 Case P600 molded plastic body over passivated junction. Pressure Cooker JESD 22-A102 Polarity Color band denotes the cathode except Bipolar. High Temp. Storage JESD22-A103 HTRB JESD22-A108 Terminal Matte Tin axial leads, solderable per JESD22-B102D. Thermal Shock JESD22-A106 Dimensions D Dimensions C A B P600 (c) 2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/04/13 A Inches Min Millimeters Max Min Max A 1.000 - 25.40 - B 0.340 0.360 8.60 9.10 C 0.048 0.052 1.22 1.32 D 0.340 0.360 8.60 9.10 Transient Voltage Suppression Diodes Axial Leaded - 5000W > 5KP series Part Numbering System Part Marking System OPTION CODE: BLANK Reel Tape -B Bulk Packaging Cathode Band TYPE CODE: A Uni-Directional (5% VBR Voltage Tolerance) CA Bi-Directional (5% VBR Voltage Tolerance) F 5KPxxx XX X YYWW Littelfuse Logo VR VOLTAGE Trace Code Marking YY:Year Code WW: Week Code 5KPXXX Product Type SERIES CODE Packing Options Component Package Quantity Packaging Option 5KPxxxXX P600 800 Tape & Reel 5KPxxxXX-B P600 100 BULK Part Number Packaging Specification EIA STD RS-296E Littelfuse Concord Packing Spec. DM-0016 Tape and Reel Specification Direction of Feed Top View Anode Lead White Type 2.75 (69.85) Front View Off Center 2.56 either side 2.062 (52.37) (65.00) 0.039(1.0) Negative Cathod Lead Red Type 0.40 (10.16) 0.048 (1.22) Recess Depth Max. 0.75 (19.05) 0.25 (6.35) 3.0 (76.2) 13.0 330.2 Dimensions are in inches/mm 0.68 (17.27) Label (c) 2013 Littelfuse, Inc. Specifications are subject to change without notice. Revised: 03/04/13