LM4667, LM4667MMBD www.ti.com SNAS165C - SEPTEMBER 2003 - REVISED MAY 2013 LM4667 Filterless High Efficiency 1.3W Switching Audio Amplifier Check for Samples: LM4667, LM4667MMBD FEATURES DESCRIPTION * The LM4667 is a fully integrated single-supply high efficiency switching audio amplifier. It features an innovative modulator that eliminates the LC output filter used with typical switching amplifiers. Eliminating the output filter reduces parts count, simplifies circuit design, and reduces board area. The LM4667 processes analog inputs with a delta-sigma modulation technique that lowers output noise and THD when compared to conventional pulse width modulators. 1 2 * * * * * * * No Output Filter Required for Inductive Transducers Selectable Gain of 6dB or 12dB Very Fast Turn on Time: 5ms (typ) Minimum External Components "Click and Pop" Suppression Circuitry Micro-Power Shutdown Mode Short Circuit Protection Space-Saving DSBGA and VSSOP Packages KEY SPECIFICATIONS * * * * * * Efficiency at 3V, 100mW into 8 Transducer 74% (typ) Efficiency at 3V, 450mW into 8 Transducer 84% (typ) Efficiency at 5V, 1W into 8 Transducer 86% (typ) Total Quiescent Power Supply Current: 3.5mA (typ) Total Shutdown Power Supply Current: 0.01A (typ) Single Supply Range: 2.7V to 5.5V APPLICATIONS * * * Mobile Phones PDAs Portable Electronic Devices The LM4667 is designed to meet the demands of mobile phones and other portable communication devices. Operating on a single 3V supply, it is capable of driving 8 transducer loads at a continuous average output of 450mW with less than 1%THD+N. Its flexible power supply requirements allow operation from 2.7V to 5.5V. The LM4667 has high efficiency with an 8 transducer load compared to a typical Class AB amplifier. With a 3V supply, the IC's efficiency for a 100mW power level is 74%, reaching 84% at 450mW output power. The LM4667 features a low-power consumption shutdown mode. Shutdown may be enabled by driving the Shutdown pin to a logic low (GND). The LM4667 has fixed selectable gain of either 6dB or 12dB. The LM4667 has short circuit protection against a short from the outputs to VDD, GND, or across the outputs. 1 2 Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. All trademarks are the property of their respective owners. PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of the Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. Copyright (c) 2003-2013, Texas Instruments Incorporated LM4667, LM4667MMBD SNAS165C - SEPTEMBER 2003 - REVISED MAY 2013 www.ti.com Typical Application Figure 1. Typical Audio Amplifier Application Circuit Connection Diagrams Top View Top View 1 10 2 9 3 8 4 7 5 6 SHUTDOWN V02 IN- VDD NC GND IN+ GAIN SELECT Figure 2. Bump DSBGA Package See Package Number YZR0009AAA 2 Submit Documentation Feedback GND V01 Figure 3. VSSOP Package See Package Number DGS0010A Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4667 LM4667MMBD LM4667, LM4667MMBD www.ti.com SNAS165C - SEPTEMBER 2003 - REVISED MAY 2013 These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Absolute Maximum Ratings (1) (2) (3) Supply Voltage (1) 6.0V -65C to +150C Storage Temperature VDD + 0.3V V GND - 0.3V Voltage at Any Input Pin (4) Internally Limited ESD Susceptibility (5) 7.0kV ESD Susceptibility (6) 250V Power Dissipation Junction Temperature (TJ) Thermal Resistance 150C JA (DSBGA) 220C/W JA (VSSOP ) 190C/W JC (VSSOP) 56C/W Soldering Information: see AN-1112 "microSMD Wafers Level Chip Scale Package." (1) (2) (3) (4) (5) (6) All voltages are measured with respect to the ground pin, unless otherwise specified. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit is given, however, the typical value is a good indication of device performance. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/ Distributors for availability and specifications. The maximum power dissipation must be derated at elevated temperatures and is dictated by TJMAX, JA, and the ambient temperature TA. The maximum allowable power dissipation is PDMAX = (TJMAX-TA)/JA or the number given in Absolute Maximum Ratings, whichever is lower. For the LM4667, TJMAX = 150C. The typical JA is 220C/W for the DSBGA package and 190C/W for the VSSOP package. Human body model, 100pF discharged through a 1.5k resistor. Machine Model, 220pF-240pF discharged through all pins. Operating Ratings (1) Temperature Range TMIN TA TMAX -40C TA 85C 2.7V VDD 5.5V Supply Voltage (1) Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit is given, however, the typical value is a good indication of device performance. Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4667 LM4667MMBD Submit Documentation Feedback 3 LM4667, LM4667MMBD SNAS165C - SEPTEMBER 2003 - REVISED MAY 2013 www.ti.com Electrical Characteristics VDD = 5V (1) (2) The following specifications apply for VDD = 5V and RL = 15H + 8 + 15H unless otherwise specified. Limits apply for TA = 25C. Parameter LM4667 Test Conditions IDD Quiescent Power Supply Current VIN = 0V, No Load VIN = 0V, RL = 15H + 8 + 15H ISD Shutdown Current VSD = GND (6) VSDIH Shutdown Voltage Input High VSDIL VGSIH Typ (3) Limit (4) (5) Units (Limits) 8 9 mA mA 0.01 A 1.2 V Shutdown Voltage Input Low 1.1 V Gain Select Input High 1.2 V VGSIL Gain Select Input Low 1.1 V AV Closed Loop Gain VGain Select = VDD 6 dB AV Closed Loop Gain VGain Select = GND 12 dB VOS Output Offset Voltage 10 mV TWU Wake-up Time 5 ms Po Output Power THD = 2% (max), f = 1kHz 1.3 W THD+N Total Harmonic Distortion+Noise PO = 100mWRMS; fIN = 1kHz 0.8 % VGain Select = VDD 90 k VGain Select = GND RIN Differential Input Resistance PSRR Power Supply Rejection Ratio 60 k VRipple = 100mVRMS sine wave Inputs terminated to GND 55 (f = 217Hz) dB VRipple = 100mVRMS sine wave POUT = 10mW,1kHz 65 (f = 217Hz) dB 41 dB CMRR Common Mode Rejection Ratio VRipple = 100mVRMS, fRipple = 217Hz SNR Signal to Noise Ratio PO = 1WRMS; A-Weighted Filter 83 dB OUT Output Noise A-Weighted filter, Vin = 0V 200 V (1) (2) (3) (4) (5) (6) 4 All voltages are measured with respect to the ground pin, unless otherwise specified. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit is given, however, the typical value is a good indication of device performance. Typical specifications are specified at 25C and represent the parametric norm. Tested limits are ensured to AOQL (Average Outgoing Quality Level). Datasheet min/max specification limits are guaranteed by design, test, or statistical analysis. Shutdown current is measured in a normal room environment. Exposure to direct sunlight will increase ISD by a maximum of 2A. The Shutdown pin should be driven as close as possible to GND for minimal shutdown current and to VDD for the best THD performance in PLAY mode. See the SHUTDOWN FUNCTION section under Application Information for more information. Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4667 LM4667MMBD LM4667, LM4667MMBD www.ti.com SNAS165C - SEPTEMBER 2003 - REVISED MAY 2013 Electrical Characteristics VDD = 3V (1) (2) The following specifications apply for VDD = 3V and RL = 15H + 8 + 15H unless otherwise specified. Limits apply for TA = 25C. Parameter IDD LM4667 Test Conditions Quiescent Power Supply Current VIN = 0V, No Load VIN = 0V, RL = 15H + 8 + 15H VSD = GND (6) Typ (3) Limit (4) (5) Units (Limits) 3.50 3.75 5.0 mA (max) ISD Shutdown Current 0.01 2.0 A (max) VSDIH Shutdown Voltage Input High 1.0 1.4 V (min) VSDIL Shutdown Voltage Input Low 0.8 0.4 V (max) VGSIH Gain Select Input High 1.0 1.4 V (min) VGSIL Gain Select Input Low 0.8 0.4 V (max) AV Closed Loop Gain VGain Select = VDD 6 5.5 6.5 dB (min) dB (max) AV Closed Loop Gain VGain Select = GND 12 11.5 12.5 dB (min) dB (max) VOS Output Offset Voltage 10 25 mV (max) TWU Wake-up Time 5 Po Output Power THD = 1% (max); f = 1kHz 450 425 mW (min) THD+N Total Harmonic Distortion+Noise PO = 100mWRMS; fIN = 1kHz ms 0.35 % VGain Select = VDD 90 k VGain Select = GND 60 k Vripple = 100mVRMS sine wave Inputs terminated to GND 56 (f = 217Hz) dB VRipple = 100mVRMS sine wave POUT = 10mW,1kHz 65 (f = 217Hz) dB 41 dB RIN Differential Input Resistance PSRR Power Supply Rejection Ratio CMRR Common Mode Rejection Ratio VRipple = 100mVRMS, fRipple = 217Hz SNR Signal to Noise Ratio PO = 400mWRMS, A-Weighted Filter 83 dB OUT Output Noise A-Weighted filter, Vin = 0V 125 V (1) (2) (3) (4) (5) (6) All voltages are measured with respect to the ground pin, unless otherwise specified. Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. Electrical Characteristics state DC and AC electrical specifications under particular test conditions which guarantee specific performance limits. This assumes that the device is within the Operating Ratings. Specifications are not guaranteed for parameters where no limit is given, however, the typical value is a good indication of device performance. Typical specifications are specified at 25C and represent the parametric norm. Tested limits are ensured to AOQL (Average Outgoing Quality Level). Datasheet min/max specification limits are guaranteed by design, test, or statistical analysis. Shutdown current is measured in a normal room environment. Exposure to direct sunlight will increase ISD by a maximum of 2A. The Shutdown pin should be driven as close as possible to GND for minimal shutdown current and to VDD for the best THD performance in PLAY mode. See the SHUTDOWN FUNCTION section under Application Information for more information. External Components Description (See Figure 1) Components Functional Description 1. CS Supply bypass capacitor which provides power supply filtering. Refer to the Power Supply Bypassing section for information concerning proper placement and selection of the supply bypass capacitor. 2. CI Input AC coupling capacitor which blocks the DC voltage at the amplifier's input terminals. Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4667 LM4667MMBD Submit Documentation Feedback 5 LM4667, LM4667MMBD SNAS165C - SEPTEMBER 2003 - REVISED MAY 2013 www.ti.com Typical Performance Characteristics 6 THD+N vs Frequency VDD = 5V, RL = 15H + 8 + 15H POUT = 100mW, 30kHz BW THD+N vs Frequency VDD = 3V, RL = 15H + 8 + 15H POUT = 100mW, 30kHz BW Figure 4. Figure 5. THD+N vs Frequency VDD = 3V, RL = 15H + 4 + 15H POUT = 300mW, 30kHz BW THD+N vs Power Out VDD = 5V, RL = 15H + 8 + 15H f = 1kHz, 22kHz BW Figure 6. Figure 7. THD+N vs Power Out VDD = 3V, RL = 15H + 4 + 15H f = 1kHz, 22kHz BW THD+N vs Power Out VDD = 3V, RL = 15H + 8 + 15H f = 1kHz, 22kHz BW Figure 8. Figure 9. Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4667 LM4667MMBD LM4667, LM4667MMBD www.ti.com SNAS165C - SEPTEMBER 2003 - REVISED MAY 2013 Typical Performance Characteristics (continued) CMRR vs Frequency VDD = 5V, RL = 15H + 8 + 15H VCM = 300mVRMS Sine Wave, 30kHz BW CMRR vs Frequency VDD = 3V, RL = 15H + 8 + 15H VCM = 300mVRMS Sine Wave, 30kHz BW Figure 10. Figure 11. PSRR vs Frequency VDD = 5V, RL = 15H + 8 + 15H VRipple = 100mVRMS Sine Wave, 22kHz BW PSRR vs Frequency VDD = 3V, RL = 15H + 8 + 15H VRipple = 100mVRMS Sine Wave, 22kHz BW Figure 12. Figure 13. Efficiency and Power Dissipation vs Output Power VDD = 5V, RL = 15H + 8 + 15H, f = 1kHz, THD < 2% Efficiency and Power Dissipation vs Output Power VDD = 3V, RL = 15H + 8 + 15H, f = 1kHz, THD < 1% Figure 14. Figure 15. Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4667 LM4667MMBD Submit Documentation Feedback 7 LM4667, LM4667MMBD SNAS165C - SEPTEMBER 2003 - REVISED MAY 2013 www.ti.com Typical Performance Characteristics (continued) 8 Efficiency and Power Dissipation vs Output Power VDD = 3V, RL = 15H + 4 + 15H, f = 1kHz, THD < 1% Gain Select Threshold VDD = 3V Figure 16. Figure 17. Gain Select Threshold VDD = 5V Gain Select Threshold vs Supply Voltage RL = 15H + 8 + 15H Figure 18. Figure 19. Output Power vs Supply Voltage RL = 15H + 4 + 15H, f = 1kHz Output Power vs Supply Voltage RL = 15H + 8 + 15H, f = 1kHz Figure 20. Figure 21. Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4667 LM4667MMBD LM4667, LM4667MMBD www.ti.com SNAS165C - SEPTEMBER 2003 - REVISED MAY 2013 Typical Performance Characteristics (continued) Output Power vs Supply Voltage RL = 15H + 16 + 15H, f = 1kHz Shutdown Threshold VDD = 5V Figure 22. Figure 23. Shutdown Threshold VDD = 3V Shutdown Threshold vs Supply Voltage RL = 15H + 8 + 15H Figure 24. Figure 25. Supply Current vs Shutdown Voltage RL = 15H + 8 + 15H Supply Current vs Supply Voltage RL = 15H + 8 + 15H Figure 26. Figure 27. Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4667 LM4667MMBD Submit Documentation Feedback 9 LM4667, LM4667MMBD SNAS165C - SEPTEMBER 2003 - REVISED MAY 2013 www.ti.com APPLICATION INFORMATION GENERAL AMPLIFIER FUNCTION The output signals generated by the LM4667 consist of two, BTL connected, output signals that pulse momentarily from near ground potential to VDD. The two outputs can pulse independently with the exception that they both may never pulse simultaneously as this would result in zero volts across the BTL load. The minimum width of each pulse is approximately 160ns. However, pulses on the same output can occur sequentially, in which case they are concatenated and appear as a single wider pulse to achieve an effective 100% duty cycle. This results in maximum audio output power for a given supply voltage and load impedance. The LM4667 can achieve much higher efficiencies than class AB amplifiers while maintaining acceptable THD performance. The short (160ns) drive pulses emitted at the LM4667 outputs means that good efficiency can be obtained with minimal load inductance. The typical transducer load on an audio amplifier is quite reactive (inductive). For this reason, the load can act as it's own filter, so to speak. This "filter-less" switching amplifier/transducer load combination is much more attractive economically due to savings in board space and external component cost by eliminating the need for a filter. POWER DISSIPATION AND EFFICIENCY In general terms, efficiency is considered to be the ratio of useful work output divided by the total energy required to produce it with the difference being the power dissipated, typically, in the IC. The key here is "useful" work. For audio systems, the energy delivered in the audible bands is considered useful including the distortion products of the input signal. Sub-sonic (DC) and super-sonic components (>22kHz) are not useful. The difference between the power flowing from the power supply and the audio band power being transduced is dissipated in the LM4667 and in the transducer load. The amount of power dissipation in the LM4667 is very low. This is because the ON resistance of the switches used to form the output waveforms is typically less than 0.25. This leaves only the transducer load as a potential "sink" for the small excess of input power over audio band output power. The LM4667 dissipates only a fraction of the excess power requiring no additional PCB area or copper plane to act as a heat sink. DIFFERENTIAL AMPLIFIER EXPLANATION As logic supply voltages continue to shrink, designers are increasingly turning to differential analog signal handling to preserve signal to noise ratios with restricted voltage swing. The LM4667 is a fully differential amplifier that features differential input and output stages. A differential amplifier amplifies the difference between the two input signals. Traditional audio power amplifiers have typically offered only single-ended inputs resulting in a 6dB reduction in signal to noise ratio relative to differential inputs. The LM4667 also offers the possibility of DC input coupling which eliminates the two external AC coupling, DC blocking capacitors. The LM4667 can be used, however, as a single ended input amplifier while still retaining it's fully differential benefits. In fact, completely unrelated signals may be placed on the input pins. The LM4667 simply amplifies the difference between the signals. A major benefit of a differential amplifier is the improved common mode rejection ratio (CMRR) over single input amplifiers. The common-mode rejection characteristic of the differential amplifier reduces sensitivity to ground offset related noise injection, especially important in high noise applications. PCB LAYOUT CONSIDERATIONS As output power increases, interconnect resistance (PCB traces and wires) between the amplifier, load and power supply create a voltage drop. The voltage loss on the traces between the LM4667 and the load results is lower output power and decreased efficiency. Higher trace resistance between the supply and the LM4667 has the same effect as a poorly regulated supply, increase ripple on the supply line also reducing the peak output power. The effects of residual trace resistance increases as output current increases due to higher output power, decreased load impedance or both. To maintain the highest output voltage swing and corresponding peak output power, the PCB traces that connect the output pins to the load and the supply pins to the power supply should be as wide as possible to minimize trace resistance. 10 Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4667 LM4667MMBD LM4667, LM4667MMBD www.ti.com SNAS165C - SEPTEMBER 2003 - REVISED MAY 2013 The rising and falling edges are necessarily short in relation to the minimum pulse width (160ns), having approximately 2ns rise and fall times, typical, depending on parasitic output capacitance. The inductive nature of the transducer load can also result in overshoot on one or both edges, clamped by the parasitic diodes to GND and VDD in each case. From an EMI standpoint, this is an aggressive waveform that can radiate or conduct to other components in the system and cause interference. It is essential to keep the power and output traces short and well shielded if possible. Use of ground planes, beads, and micro-strip layout techniques are all useful in preventing unwanted interference. POWER SUPPLY BYPASSING As with any power amplifier, proper supply bypassing is critical for low noise performance and high power supply rejection ratio (PSRR). The capacitor (CS) location should be as close as possible to the LM4667. Typical applications employ a voltage regulator with a 10F and a 0.1F bypass capacitors that increase supply stability. These capacitors do not eliminate the need for bypassing on the supply pin of the LM4667. A 1F tantalum capacitor is recommended. SHUTDOWN FUNCTION In order to reduce power consumption while not in use, the LM4667 contains shutdown circuitry that reduces current draw to less than 0.01A. The trigger point for shutdown is shown as a typical value in the Electrical Characteristics Tables and in the Shutdown Hysteresis Voltage graphs found in the Typical Performance Characteristics section. It is best to switch between ground and supply for minimum current usage while in the shutdown state. While the LM4667 may be disabled with shutdown voltages in between ground and supply, the idle current will be greater than the typical 0.01A value. Increased THD may also be observed with voltages less than VDD on the Shutdown pin when in PLAY mode. The LM4667 has an internal resistor connected between GND and Shutdown pins. The purpose of this resistor is to eliminate any unwanted state changes when the Shutdown pin is floating. The LM4667 will enter the shutdown state when the Shutdown pin is left floating or if not floating, when the shutdown voltage has crossed the threshold. To minimize the supply current while in the shutdown state, the Shutdown pin should be driven to GND or left floating. If the Shutdown pin is not driven to GND, the amount of additional resistor current due to the internal shutdown resistor can be found by Equation (1) below. (VSD - GND) / 60k (1) With only a 0.5V difference, an additional 8.3A of current will be drawn while in the shutdown state. GAIN SELECTION FUNCTION The LM4667 has fixed selectable gain to minimize external components, increase flexibility and simplify design. For a differential gain of 6dB, the Gain Select pin should be permanently connected to VDD or driven to a logic high level. For a differential gain of 12dB, the Gain Select pin should be permanently connected to GND or driven to a logic low level. The gain of the LM4667 can be switched while the amplifier is in PLAY mode driving a load with a signal without damage to the IC. The voltage on the Gain Select pin should be switched quickly between GND (logic low) and VDD (logic high) to eliminate any possible audible artifacts from appearing at the output. For typical threshold voltages for the Gain Select function, refer to the Gain Threshold Voltages graph in the Typical Performance Characteristics section. Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4667 LM4667MMBD Submit Documentation Feedback 11 LM4667, LM4667MMBD SNAS165C - SEPTEMBER 2003 - REVISED MAY 2013 www.ti.com SINGLE-ENDED CIRCUIT CONFIGURATIONS Figure 28. Single-Ended Input with Low Gain Selection Configuration Figure 29. Single-Ended Input with High Gain Selection Configuration 12 Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4667 LM4667MMBD LM4667, LM4667MMBD www.ti.com SNAS165C - SEPTEMBER 2003 - REVISED MAY 2013 REFERENCE DESIGN BOARD SCHEMATIC Figure 30. In addition to the minimal parts required for the application circuit, a measurement filter is provided on the evaluation circuit board so that conventional audio measurements can be conveniently made without additional equipment. This is a balanced input / grounded differential output low pass filter with a 3dB frequency of approximately 35kHz and an on board termination resistor of 300 (see Figure 30). Note that the capacitive load elements are returned to ground. This is not optimal for common mode rejection purposes, but due to the independent pulse format at each output there is a significant amount of high frequency common mode component on the outputs. The grounded capacitive filter elements attenuate this component at the board to reduce the high frequency CMRR requirement placed on the analysis instruments. Even with the grounded filter the audio signal is still differential, necessitating a differential input on any analysis instrument connected to it. Most lab instruments that feature BNC connectors on their inputs are NOT differential responding because the ring of the BNC is usually grounded. The commonly used Audio Precision analyzer is differential, but its ability to accurately reject fast pulses of 160nS width is questionable necessitating the on board measurement filter. When in doubt or when the signal needs to be single-ended, use an audio signal transformer to convert the differential output to a single ended output. Depending on the audio transformer's characteristics, there may be some attenuation of the audio signal which needs to be taken into account for correct measurement of performance. Measurements made at the output of the measurement filter suffer attenuation relative to the primary, unfiltered outputs even at audio frequencies. This is due to the resistance of the inductors interacting with the termination resistor (300) and is typically about -0.35dB (4%). In other words, the voltage levels (and corresponding power levels) indicated through the measurement filter are slightly lower than those that actually occur at the load placed on the unfiltered outputs. This small loss in the filter for measurement gives a lower output power reading than what is really occurring on the unfiltered outputs and its load. Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4667 LM4667MMBD Submit Documentation Feedback 13 LM4667, LM4667MMBD SNAS165C - SEPTEMBER 2003 - REVISED MAY 2013 www.ti.com LM4667 DSBGA BOARD ARTWORK Figure 31. Composite View Figure 32. Silk Screen 14 Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4667 LM4667MMBD LM4667, LM4667MMBD www.ti.com SNAS165C - SEPTEMBER 2003 - REVISED MAY 2013 Figure 33. Top Layer Figure 34. Bottom Layer Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4667 LM4667MMBD Submit Documentation Feedback 15 LM4667, LM4667MMBD SNAS165C - SEPTEMBER 2003 - REVISED MAY 2013 www.ti.com LM4667 VSSOP BOARD ARTWORK Figure 35. Composite View Figure 36. Silk Screen 16 Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4667 LM4667MMBD LM4667, LM4667MMBD www.ti.com SNAS165C - SEPTEMBER 2003 - REVISED MAY 2013 Figure 37. Top Layer Figure 38. Bottom Layer Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4667 LM4667MMBD Submit Documentation Feedback 17 LM4667, LM4667MMBD SNAS165C - SEPTEMBER 2003 - REVISED MAY 2013 www.ti.com REVISION HISTORY Changes from Revision B (May 2013) to Revision C * 18 Page Changed layout of National Data Sheet to TI format .......................................................................................................... 17 Submit Documentation Feedback Copyright (c) 2003-2013, Texas Instruments Incorporated Product Folder Links: LM4667 LM4667MMBD PACKAGE OPTION ADDENDUM www.ti.com 26-Aug-2013 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish (2) MSL Peak Temp Op Temp (C) Device Marking (3) (4/5) LM4667ITL/NOPB ACTIVE DSBGA YZR 9 250 Green (RoHS & no Sb/Br) SNAGCU Level-1-260C-UNLIM -40 to 85 G B4 LM4667MM/NOPB ACTIVE VSSOP DGS 10 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 85 GA6 (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 Samples PACKAGE MATERIALS INFORMATION www.ti.com 12-Aug-2013 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) LM4667ITL/NOPB DSBGA YZR 9 250 178.0 8.4 LM4667MM/NOPB VSSOP DGS 10 1000 178.0 12.4 Pack Materials-Page 1 B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 1.7 1.7 0.76 4.0 8.0 Q1 5.3 3.4 1.4 8.0 12.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 12-Aug-2013 *All dimensions are nominal Device Package Type Package Drawing LM4667ITL/NOPB DSBGA YZR LM4667MM/NOPB VSSOP DGS Pins SPQ Length (mm) Width (mm) Height (mm) 9 250 210.0 185.0 35.0 10 1000 210.0 185.0 35.0 Pack Materials-Page 2 MECHANICAL DATA YZR0009xxx D 0.6000.075 E TLA09XXX (Rev C) D: Max = 1.545 mm, Min =1.484 mm E: Max = 1.545 mm, Min =1.484 mm 4215046/A NOTES: A. All linear dimensions are in millimeters. Dimensioning and tolerancing per ASME Y14.5M-1994. B. This drawing is subject to change without notice. www.ti.com 12/12 IMPORTANT NOTICE Texas Instruments Incorporated (TI) reserves the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. TI's published terms of sale for semiconductor products (http://www.ti.com/sc/docs/stdterms.htm) apply to the sale of packaged integrated circuit products that TI has qualified and released to market. Additional terms may apply to the use or sale of other types of TI products and services. Reproduction of significant portions of TI information in TI data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such reproduced documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyers and others who are developing systems that incorporate TI products (collectively, "Designers") understand and agree that Designers remain responsible for using their independent analysis, evaluation and judgment in designing their applications and that Designers have full and exclusive responsibility to assure the safety of Designers' applications and compliance of their applications (and of all TI products used in or for Designers' applications) with all applicable regulations, laws and other applicable requirements. Designer represents that, with respect to their applications, Designer has all the necessary expertise to create and implement safeguards that (1) anticipate dangerous consequences of failures, (2) monitor failures and their consequences, and (3) lessen the likelihood of failures that might cause harm and take appropriate actions. Designer agrees that prior to using or distributing any applications that include TI products, Designer will thoroughly test such applications and the functionality of such TI products as used in such applications. TI's provision of technical, application or other design advice, quality characterization, reliability data or other services or information, including, but not limited to, reference designs and materials relating to evaluation modules, (collectively, "TI Resources") are intended to assist designers who are developing applications that incorporate TI products; by downloading, accessing or using TI Resources in any way, Designer (individually or, if Designer is acting on behalf of a company, Designer's company) agrees to use any particular TI Resource solely for this purpose and subject to the terms of this Notice. TI's provision of TI Resources does not expand or otherwise alter TI's applicable published warranties or warranty disclaimers for TI products, and no additional obligations or liabilities arise from TI providing such TI Resources. TI reserves the right to make corrections, enhancements, improvements and other changes to its TI Resources. TI has not conducted any testing other than that specifically described in the published documentation for a particular TI Resource. Designer is authorized to use, copy and modify any individual TI Resource only in connection with the development of applications that include the TI product(s) identified in such TI Resource. NO OTHER LICENSE, EXPRESS OR IMPLIED, BY ESTOPPEL OR OTHERWISE TO ANY OTHER TI INTELLECTUAL PROPERTY RIGHT, AND NO LICENSE TO ANY TECHNOLOGY OR INTELLECTUAL PROPERTY RIGHT OF TI OR ANY THIRD PARTY IS GRANTED HEREIN, including but not limited to any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information regarding or referencing third-party products or services does not constitute a license to use such products or services, or a warranty or endorsement thereof. Use of TI Resources may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. TI RESOURCES ARE PROVIDED "AS IS" AND WITH ALL FAULTS. TI DISCLAIMS ALL OTHER WARRANTIES OR REPRESENTATIONS, EXPRESS OR IMPLIED, REGARDING RESOURCES OR USE THEREOF, INCLUDING BUT NOT LIMITED TO ACCURACY OR COMPLETENESS, TITLE, ANY EPIDEMIC FAILURE WARRANTY AND ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT OF ANY THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. TI SHALL NOT BE LIABLE FOR AND SHALL NOT DEFEND OR INDEMNIFY DESIGNER AGAINST ANY CLAIM, INCLUDING BUT NOT LIMITED TO ANY INFRINGEMENT CLAIM THAT RELATES TO OR IS BASED ON ANY COMBINATION OF PRODUCTS EVEN IF DESCRIBED IN TI RESOURCES OR OTHERWISE. IN NO EVENT SHALL TI BE LIABLE FOR ANY ACTUAL, DIRECT, SPECIAL, COLLATERAL, INDIRECT, PUNITIVE, INCIDENTAL, CONSEQUENTIAL OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF TI RESOURCES OR USE THEREOF, AND REGARDLESS OF WHETHER TI HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Unless TI has explicitly designated an individual product as meeting the requirements of a particular industry standard (e.g., ISO/TS 16949 and ISO 26262), TI is not responsible for any failure to meet such industry standard requirements. Where TI specifically promotes products as facilitating functional safety or as compliant with industry functional safety standards, such products are intended to help enable customers to design and create their own applications that meet applicable functional safety standards and requirements. Using products in an application does not by itself establish any safety features in the application. Designers must ensure compliance with safety-related requirements and standards applicable to their applications. Designer may not use any TI products in life-critical medical equipment unless authorized officers of the parties have executed a special contract specifically governing such use. Life-critical medical equipment is medical equipment where failure of such equipment would cause serious bodily injury or death (e.g., life support, pacemakers, defibrillators, heart pumps, neurostimulators, and implantables). Such equipment includes, without limitation, all medical devices identified by the U.S. Food and Drug Administration as Class III devices and equivalent classifications outside the U.S. TI may expressly designate certain products as completing a particular qualification (e.g., Q100, Military Grade, or Enhanced Product). Designers agree that it has the necessary expertise to select the product with the appropriate qualification designation for their applications and that proper product selection is at Designers' own risk. Designers are solely responsible for compliance with all legal and regulatory requirements in connection with such selection. Designer will fully indemnify TI and its representatives against any damages, costs, losses, and/or liabilities arising out of Designer's noncompliance with the terms and provisions of this Notice. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2017, Texas Instruments Incorporated Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Texas Instruments: LM4667MMBD/NOPB LM4667ITL/NOPB LM4667ITLX/NOPB LM4667MM/NOPB