134
NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com
Miniature Aluminum Electrolytic Capacitors
RADIAL LEADS, POLARIZED, NEW FURTHER REDUCED CASE SIZING,
FROM NRWA WIDE TEMPERATURE RANGE
NRWS Series
CHARACTERISTICS
Note: Capacitors shall conform to JIS-C-5141, unless otherwise specifi ed here.
*1. Add 0.5 every 1000μF for more than 1000μF *2. Add 1.0 every 1000μF for more than 1000μF
EX TEND ED TEM PER A TURE
NRWA NRWS
(today’s standard) (reduced sizes)
Rated Voltage Range 6.3 ~ 100VDC
Capacitance Range 0.1 ~ 15,000μF
Operating Temperature Range -55°C ~ +105°C
Capacitance Tolerance ±20% (M)
Maximum Leakage Current @ +20°c After 1 min. 0.03CV or 4μA whichever is greater
After 2 min. 0.01CV or 3μA whichever is greater
Max. Tan δ at 120Hz/20°C
W.V. (Vdc) 6.3 10 16 25 35 50 63 100
S.V. (Vdc) 8 13 20 32 44 63 79 125
C < 1,000μF0.28 0.24 0.20 0.16 0.14 0.12 0.10 0.08
C = 2,200μF0.30 0.26 0.22 0.18 0.16 0.14 - -
C = 3,300μF0.32 0.28 0.24 0.20 0.18 0.16 - -
C = 4,700μF0.34 0.30 0.26 0.22 0.20 - - -
C = 6,800μF0.36 0.32 0.28 0.24 ----
C = 10,000μF0.38 0.34 0.30 -----
C = 15,000μF0.56 0.52 ------
Low Temperature Stability
Impedance Ratio @ 120Hz
Z-25°C/Z+20°C 54322222
Z-40°C/Z+20°C 12 10 854444
Load Life Test at +105°C & Rated W.V
2,000 Hours: 16V ~ 100V D> 10φ
1,000 Hours: All others
Δ Capacitance Within ±20% of initial measured value
Δ Tan δLess than 200% of specifi ed value
Δ LC Less than specifi ed value
Shelf Life Test
+105°C 1,000 Hours
No Load
Δ Capacitance Within ±20% of initial measured value
Δ Tan δLess than 200% of specifi ed value
Δ LC Less than specifi ed value
LEAD SPACING AND DIAMETER (mm)
Cap.
(μF) Code Working Voltage (Vdc)
6.3 10 16 25 35 50 63 100
0.1 R10 - - - - - 5x11 - -
0.22 R22 - - - - - 5x11 - -
0.33 R33 - - - - - 5x11 - -
0.47 R47 - - - - - 5x11 5x11 -
1.0 1R0 - - - - - 5x11 5x11 -
2.2 2R2 - - - - - 5x11 5x11 -
3.3 3R3 - - - - - 5x11 5x11 -
4.7 4R7 - - - - - 5x11 5x11 -
10 100 - - - - - 5x11 5x11 -
22 220 - - - - - 5x11 5x11 8x11.5
33 330 - - - - 5x11 5x11 6.3x11 8x12.5
47 470 - - - 5x11 5x11 6.3x11 6.3x11 10x12.5
100 101 - 5x11 5x11 6.3x11 6.3x11 8x11.5 8x12.5 10x20
220 221 5x11 6.3x11 6.3x11 8x11.5 8x11.5 10x12.5 10x16 12.5x25
330 331 6.3x11 6.3x11 8x11.5 8x11.5 10x12.5 10x16 10x20 16x25
470 471 6.3x11 6.3x11 8x11.5 10x12.5 10x16 10x20 12.5x20 16x31
1,000 102 8x11.5 10x12.5 10x16 10x20 12.5x20 12.5x25 16x25 -
2,200 222 10x16 10x20 12.5x20 12.5x25 16x25 16x31 - -
3,300 332 10x20 12.5x20 12.5x25 16x25 16x35 18x36 - -
4,700 472 12.5x20 12.5x25 16x25 16x31 18x36 - - -
6,800 682 12.5x25 16x25 16x31 18x36 - - - -
10,000 103 16x25 16x31 18x36 - - - - -
15,000 153 16x36 18x36 - - - - - -
Case Dia. (Dφ)5 6.3 8 10 12.5 16 18
Lead Dia. (Dφ)0.5 0.5 0.6 0.6 0.6 0.8 0.8
Lead Spacing (F) 2.0 2.5 3.5 5.0 5.0 7.5 7.5
Dim. α0.5 0.5 0.5 0.5 0.5 0.5 0.5
STANDARD PRODUCT AND CASE SIZE TABLE Dφ x L (mm)
*See Part Number System for Details
P N bS fD il
RoHS
Compliant
includes all homogeneous materials
135
NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com
Miniature Aluminum Electrolytic Capacitors NRWS Series
Part Number Cap.
(μF)
W.V.
(Vdc)
Dissipation Factor
+20°C/120Hz
Ripple Current Rating (mA)
+105°C/100kHz
Max. Impedance (Ω)
+20°C/100KHz
Load Life Hours
@+105°C
NRWS221M6.3V5x11F 220
6.3
0.28 160 1.40 1,000
NRWS331M6.3V6.3x11F 330 0.28 240 0.58 1,000
NRWS471M6.3V6.3x11F 470 0.28 250 0.55 1,000
NRWS102M6.3V8x11.5F 1,000 0.28 450 0.26 1,000
NRWS222M6.3V10x16F 2,200 0.30 760 0.12 2,000
NRWS332M6.3V10x20F 3,300 0.32 900 0.10 2,000
NRWS472M6.3V12.5x20F 4,700 0.34 1100 0.072 2,000
NRWS682M6.3V12.5x25F 6,800 0.36 1420 0.054 2,000
NRWS103M6.3V16x25F 10,000 0.38 1700 0.043 2,000
NRWS153M6.3V16x36F 15,000 0.56 2100 0.032 2,000
NRWS100M10V5x11F 100
10
0.24 150 1.40 1,000
NRWS220M10V6.3x11F 220 0.24 240 0.58 1,000
NRWS331M10V6.3x11F 330 0.24 250 0.55 1,000
NRWS471M10V6.3x11F 470 0.24 370 0.39 1,000
NRWS102M10V10x12.5F 1,000 0.24 560 0.16 2,000
NRWS222M10V10x20F 2,200 0.26 900 0.10 2,000
NRWS332M10V12.5x20F 3,300 0.28 1100 0.074 2,000
NRWS472M10V12.5x25F 4,700 0.30 1420 0.054 2,000
NRWS682M10V16x25F 6,800 0.32 1700 0.043 2,000
NRWS103M10V16x31F 10,000 0.34 1950 0.035 2,000
NRWS153M10V18x36F 15,000 0.52 2400 0.028 2,000
NRWS101M16V5x11F 100
16
0.20 150 1.40 1,000
NRWS221M16V6.3x11F 220 0.20 240 0.55 1,000
NRWS331M16V8x11.5F 330 0.20 370 0.35 1,000
NRWS471M16V8x11.5F 470 0.20 450 0.28 1,000
NRWS102M16V10x16F 1,000 0.20 760 0.13 2,000
NRWS222M16V12.5x20F 2,200 0.22 1100 0.075 2,000
NRWS332M16V12.5x25F 3,300 0.24 1320 0.054 2,000
NRWS101M16V16x25F 4,700 0.26 1600 0.043 2,000
NRWS682M16V16x31F 6,800 0.28 1900 0.035 2,000
NRWS103M16V18x36F 10,000 0.30 2300 0.028 2,000
NRWS470M25V5x11F 47
25
0.16 150 1.40 1,000
NRWS101M25V6.3x11F 100 0.16 240 0.60 1,000
NRWS221M25V8x11.5F 220 0.16 370 0.39 1,000
NRWS331M25V8x11.5F 330 0.16 400 0.34 1,000
NRWS471M25V10x12.5F 470 0.16 560 0.17 2,000
NRWS102M25V10x20F 1,000 0.16 900 0.10 2,000
NRWS222M25V12.5x25F 2,200 0.18 1320 0.062 2,000
NRWS332M25V16x25F 3,300 0.20 1600 0.043 2,000
NRWS472M25V16x31F 4,700 0.22 1900 0.035 2,000
NRWS682M25V18x36F 6,800 0.24 2200 0.028 2,000
NRWS330M35V5x11F 33
35
0.14 120 2.10 1,000
NRWS470M35V5x11F 47 0.14 140 2.10 1,000
NRWS101M35V6.3x11F 100 0.14 180 1.10 1,000
NRWS221M35V8x11.5F 220 0.14 360 0.46 1,000
NRWS331M35V10x12.5F 330 0.14 580 0.26 1,000
NRWS471M35V10x16F 470 0.14 650 0.18 1,000
NRWS102M35V12.5x20F 1,000 0.14 900 0.11 2,000
NRWS222M35V16x25F 2,200 0.16 1400 0.056 2,000
NRWS332M35V16x35F 3,300 0.18 1800 0.038 2,000
NRWS472M35V18x36F 4,700 0.20 2000 0.035 2,000
NRWSR10M50V5x11F 0.1
50
0.12 10 30 1,000
NRWSR22M50V5x11F 0.22 0.12 10 20 1,000
NRWSR33M50V5x11F 0.33 0.12 10 15 1,000
NRWSR47M50V5x11F 0.47 0.12 20 10 1,000
NRWS1R0M50V5x11F 1.0 0.12 30 7.0 1,000
NRWS2R2M50V5x11F 2.2 0.12 40 5.5 1,000
NRWS3R3M50V5x11F 3.3 0.12 50 4.0 1,000
NRWS4R7M50V5x11F 4.7 0.12 80 2.80 1,000
NRWS100M50V5x11F 10 0.12 90 2.30 1,000
NRWS220M50V5x11F 22 0.12 110 2.20 1,000
STANDARD VALUES, SPECIFICATIONS AND CASE SIZES (mm)
For Automotive Applications see part number system
136
NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com
RIPPLE CURRENT CORRECTION FACTORS
Cap. (μF) Frequency (Hz)
100 1K 10K ~
~ 47 0.50 0.80 1.0
> 47 ~ 220 0.55 0.85 1.0
> 220 ~ 1,000 0.65 0.90 1.0
> 1,000 0.75 0.90 1.0
Part Number Cap.
(μF)
W.V.
(Vdc)
Dissipation Factor
+20°C/120Hz
Ripple Current Rating (mA)
+105°C/100KHz
Max. Impedance (Ω)
+20°C/100KHz
Load Life Hours
@+105°C
NRWS330M50V5x11F 33
50
0.12 120 2.10 1,000
NRWS470M50V6.3x11F 47 0.12 180 1.10 1,000
NRWS101M50V8x11.5F 100 0.12 310 310 1,000
NRWS221M50V10x12.5F 220 0.12 500 0.30 2,000
NRWS331M50V10x16F 330 0.12 650 0.20 2,000
NRWS471M50V10x20F 470 0.12 800 0.13 2,000
NRWS102M50V12.5x25F 1,000 0.12 1100 0.10 2,000
NRWS222M50V16x31F 2,200 0.14 1650 0.055 2,000
NRWS332M50V18x36F 3,300 0.16 2000 0.035 2,000
NRWSR47M63V5x11F 0.47
63
0.10 15 15 1,000
NRWS1R0M63V5x11F 1.0 0.10 30 10.5 1,000
NRWS2R2M63V5x11F 2.2 0.10 42 8.3 1,000
NRWS3R3M63V5x11F 3.3 0.10 58 6.0 1,000
NRWS4R7M63V5x11F 4.7 0.10 64 4.20 1,000
NRWS100M63V5x11F 10 0.10 90 2.80 1,000
NRWS220M63V5x11F 22 0.10 140 2.40 1,000
NRWS330M63V6.3x11F 33 0.10 200 1.40 1,000
NRWS470M63V6.3x11F 47 0.10 240 1.30 1,000
NRWS101M63V8x12.5F 100 0.10 300 300 1,000
NRWS221M63V10x16F 220 0.10 520 0.22 2,000
NRWS331M63V10x20F 330 0.10 765 0.17 2,000
NRWS471M63V12.5x20F 470 0.10 960 0.14 2,000
NRWS102M63V16x25F 1,000 0.10 1100 0.065 2,000
NRWS220M100V8x11.5F 22
100
0.08 235 0.83 1,000
NRWS330M100V8x12.5F 33 0.08 300 0.60 1,000
NRWS470M100V10x12.5F 47 0.08 330 0.39 2,000
NRWS101M100V10x20F 100 0.08 450 450 2,000
NRWS221M100V12.5x25F 220 0.08 700 0.15 2,000
NRWS331M100V16x25F 330 0.08 950 0.09 2,000
NRWS471M100V16x31F 470 0.08 1100 0.085 2,000
PRECAUTIONS
Please review the notes on correct use, safety and precautions found on pages T10 & T11
of NIC’s Electrolytic Capacitor catalog.
Also found at www.niccomp.com/precautions
If in doubt or uncertainty, please review your specifi c application - process details with
NIC’s technical support personnel: tpmg@niccomp.com
Miniature Aluminum Electrolytic Capacitors NRWS Series
STANDARD VALUES, SPECIFICATIONS AND CASE SIZES (mm)
β = L < 20mm = 1.5mm, L > 20mm = 2.0mm
For Automotive Applications see part number system
PART NUMBER SYSTEM
NRWS 101 M 35V 6.3X11 TB Y F .
RoHS Compliant
TB = Tape & Box*
Case Size (Dφ x L)
Working Voltage (Vdc)
Tolerance Code (M=20%)
Capacitance Code: First 2 characters
signifi cant, third character is multiplier
Series
*see taping specifi cations for details
Optional: For automotive equipment, sourced to special
production and inspection at TS-16949 certifi ed production site
DIMENSIONS (mm)
dφ ± 0.05
Insulation Sleeve
F ± 0.5
Dφ ± α
4mm
Min.
15mm Min.
L + β max.
Polarity Marking
Drawing is representative of parts as supplied in bulk or
straight lead format, please see taping specifi cation for details
on taped format packaging.
-
+
198 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com
Miniature Aluminum Electrolytic Capacitors Taping Specifi cations
Taping Dimensions (mm)
Taping Dimensions (mm)
NOTE: ANODE (+) LEAD FEEDS OFF FIRST.
FOR OPTION OF NEGATIVE (
_) LEAD FIRST,
SPECIFY “TBN”.
STANDARD RADIAL TAPING (5mm LEAD SPACING, FORMED LEADS) TB
Case Dia.
(Dφ)10 12.5
Case Size All All
Dim.
dφ ±0.05 0.6 0.6
H ±0.75 19.0 19.0
F +0.8 ~ -0.2 5.0 5.0
P ±1.0 25.4*
P012.7 ±0.2
P13.85
P26.35 ±1.0
W 18.0 ±0.5
W011.5 min
W19.0 ±0.5
W20 ~ 2.5
H016.0 ±0.5
I 1.0 max.
D0φ4.0 ±0.2
Δh 0 ±1.0 (at top of can)
t 0.7 ±0.2 (not including lead)
*Optional Taping Specifi cations
10mm diameter available with P dim. = 12.7mm
(P/N Suffi x: TB12.7MMP)
12.5mm diameter available with P dim. = 15mm, P1= 5.0mm,
P0 = 15.0mm & P2 = 7.5mm (P/N Suffi x: TB15MMP)
Case Dia.
(Dφ)4 5 6.3 8
Case Size 4x5
4x7 5x5
5x7 5x11 6.3x5
6.3x7 6.3x11 8x11.5
Dim.
dφ ±0.05 0.45 0.45 0.5 0.45 0.5 0.6
H ±0.75 17.5 17.5 18.5 17.5 18.5 20.0
F +0.8 ~ -0.2 5.0 -02 ~ +0.8
P 12.7 ±1.0
P012.7 ±0.2
P13.85 ±0.5 (at end of tape)
P26.35 ±1.0
W 18.0 ±0.5
W011.5 min.
W19.0 ±0.5
W20 ~ 2.5
H016.0 ±0.5
I 1.0 max.
D0φ4.0 ±0.2
Δh 0 ±1.0 (at top of can)
t 0.7 ±0.2 (not including lead)
STANDARD RADIAL TAPING (5mm LEAD SPACING, STRAIGHT LEADS) TB
P2P
∅D
P1
w2
w0
w
0
P0
F
S∅D0
∅dWH
H0
1max
t
Δh
1max
t
Δh
P2P
∅D
P1
w2
w0
w
0
P0
F
S∅D0
∅dW1H
199
NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com
Taping Dimensions (mm) SPECIAL STRAIGHT LEAD TAPING TBST
SPECIAL RADIAL TAPING (2.5mm LEAD SPACING, FORMED LEADS) TBF1
Case Dia.
(Dφ)4 5 6.3 8
Case Size 4x5
4x7 5x5
5x7 5x11 6.3x5
6.3x7 6.3x11 8x11.5
Dim.
dφ ±0.05 0.45 0.45 0.5 0.45 0.5 0.6
H ±0.75 17.5 17.5 18.5 17.5 18.5 20.0
F +0.8 ~ -0.2 2.0* 2.0 2.0 2.5 2.5 3.5
P ±1.0 12.7 ±0.2
P012.7 ±0.2
P15.1 5.1 5.1 5.1 5.1 4.6
P26.35 ±1.0
W 18.0 ±0.5
W011.5 min.
W19.0 ±0.5
W20 ~ 2.5
H016.0 ±0.5
I 1.0 max.
D0φ4.0 ±0.2
Δh 0 ±1.0 (at top of can)
t 0.7 ±0.2 (not including lead)
* Parts with 4mm diameter are taped with a slight fl are in the
lead and a 2.0mm lead-space.
Miniature Aluminum Electrolytic Capacitors Taping Specifi cations
Case Dia.
(Dφ)45
Case Size 4x5
4x7 5x5
5x7 5x11
Dim.
dφ ±0.05 0.45 0.45 0.5
H ±0.75 17.5 17.5 18.5
H0 ±0.5 16.0 - -
F 2.5 -02 ~ +0.8
P 12.7 ±1.0
P012.7 ±0.2
P15.1 ±0.5
P26.35 ±1.0
W 18.0 ±0.5
W011.5 min.
W19.0 ±0.5
W20 ~ 1.5
I 1.0 max.
D0φ4.0 ±0.2
Δh 0 ±1.0
t 0.7 ±0.2
Taping Dimensions (mm)
1max
t
Δh
P2P
∅D
P1
w2
w0
w
0
P0
F
S∅D0
∅dW1H
P2P
∅D
P1
w2
w0
w
0
P0
F
S∅D0
∅dWH
1max
t
Δh
H0
200 NIC COMPONENTS CORP. www.niccomp.com www.lowESR.com www.RFpassives.com www.SMTmagnetics.com
Miniature Aluminum Electrolytic Capacitors
RADIAL TAPED PACKAGING
Taping Specifi cations
Ammo Box (Tape & Box) TB, TBF1, TBST
Size of box and component quantity
*Special Taping Consult Factory For Availability
Ammo Box Dimensions (mm)
Scored corner
L
H
W
Label ⊕
-
Case Dia (Dφ)
or Case Size Q'ty per
Box
(pcs) Dim. L Dim. H Dim.
W
4x5, 4x7 2,000 331 175 43
5x5, 5x7 2,000 331 220 43
5x11 2,000 340 255 55
6.3x5, 6.3x7 2,000 331 280 43
6.3x11 2,000 331 280 48
8x11.5, 8x12.5 1,000 335 235 53
10x12.5* 500 335 190 53
10x16* 500 335 300 53
10x20* 500 335 300 55
12.x20* 500 335 300 55
12.5x25* 500 335 300 61
