W681310
- 1 -
W681310
3V SINGLE CHANNEL
VOICEBAND CODEC
Data Sheet
Revision B18
W681310
Publication Release Date: February 2015
- 2 - Revision B18
1. GENERAL DESCRIPTION
The W681310 is a general-purpose single channel PCM CODEC with pin-selectable -Law or A-Law
companding. The device is compliant with the ITU G.712 specification. It operates from a single +3V
power supply and is available in 20-pin SOG, SSOP and TSSOP package options. Functions
performed include digitization and reconstruction of voice signals, and band limiting and smoothing
filters required for PCM systems. W681310 performance is specified over the industrial temperature
range of –40C to +85C.
The W681310 includes an on-chip precision voltage reference and an additional power amplifier,
capable of driving 300 loads differentially up to a level of 3.544V peak-to-peak. The analog section is
fully differential, reducing noise and improving the power supply rejection ratio. The data transfer
protocol supports both long-frame and short-frame synchronous communications for PCM
applications, and IDL and GCI communications for ISDN applications. W681310 accepts eight master
clock rates between 256 kHz and 4.800 MHz, and an on-chip pre-scaler automatically determines the
division ratio for the required internal clock.
For fast evaluation and prototyping purposes, the W681310DK development kit is available.
2. FEATURES
Single +3V power supply (2.7V to 5.25V)
Typical power dissipation of 10 mW,
power-down mode of 0.5 W
Fully-differential analog circuit design
On-chip precision reference of 0.886 V for
a -5 dBm TLP at 600
Push-pull power amplifiers with external
gain adjustment with 300 load capability
Eight master clock rates of 256 kHz to
4.800 MHz
Pin-selectable -Law and A-Law
companding (compliant with ITU G.711)
CODEC A/D and D/A filtering compliant
with ITU G.712
Industrial temperature range (–40C to
+85C)
Packages: 20-pin SOG (SOP), SSOP and
TSSOP
Pb-Free package options available
ApplIcations
VoIP, Voice over Networks
Digital telephone and communication
systems
Wireless voice devices
PABX/SOHO systems
Local loop card
SOHO routers
Fiber-to-curb equipment
Enterprise phones
ISDN equipment
Modems/PC cards
Digital Voice Recorders
W681310
Publication Release Date: February 2015
- 3 - Revision B18
3. BLOCK DIAGRAM
256 kHz,
512 kHz,
1536 kHz,
1544 kHz,
2048 kHz,
2560 kHz
4096 kHz
MCLK
256 kHz
8 kHz
Pre
-
scaler
V
DD
V
SS
Power Conditioning
Voltage reference
V
AG
PUI
G.712 CODEC
G.711
/A
-
Law
PAO+
PAO-
PAI
RO
-
AO
AI+
AI-
/A
-
Law
Tra
ns
mit
PC
M
Int
erf
ace
Re
cei
ve
PC
M
Int
erf
ace
FST
PCMT
FSR
BCLKR
PCMR
V
REF
256 kHz,
512 kHz,
1536 kHz,
1544 kHz,
2048 kHz,
2560 kHz
MCLK
256 kHz
8 kHz
Pre
-
Scaler
Power Conditioning
Voltage reference
V
AG
G.712 CODEC
G.711
/A
-
Law
RO
/A
-
Law
G.712 CODEC
G.711
/A
-
Law
RO
/A
-
Law
Transmit
PCM
Interface
Receive
PCM
Interface
BCLKR
V
& 4800 kHz
W681310
Publication Release Date: February 2015
- 4 - Revision B18
4. TABLE OF CONTENTS
1. GENERAL DESCRIPTION .................................................................................................................. 2
2. FEATURES ......................................................................................................................................... 2
3. BLOCK DIAGRAM .............................................................................................................................. 3
4. TABLE OF cONTENTS ....................................................................................................................... 4
5. PIN CONFIGURATION ....................................................................................................................... 6
6. PIN DESCRIPTION ............................................................................................................................. 7
7. FUNCTIONAL DESCRIPTION ............................................................................................................ 9
7.1. Transmit Path ................................................................................................................................ 9
7.2. Receive Path ............................................................................................................................... 10
7.3. Power Management ..................................................................................................................... 11
7.3.1. Analog and Digital Supply ..................................................................................................... 11
7.3.2. Analog Ground Reference Bypass ....................................................................................... 11
7.3.3. Analog Ground Reference Voltage Outpt ............................................................................. 11
7.4. PCM Interface .............................................................................................................................. 11
7.4.1. Long Frame Sync .................................................................................................................. 11
7.4.2. Short Frame Sync ................................................................................................................. 12
7.4.3. General Circuit Interface (GCI) ............................................................................................. 12
7.4.4. Interchip Digital Link (IDL) ..................................................................................................... 12
7.4.5. System Timing ...................................................................................................................... 13
8. TIMING DIAGRAMS .......................................................................................................................... 14
9. ABSOLUTE MAXIMUM RATINGS .................................................................................................... 21
9.1. Absolute Maximum Ratings ......................................................................................................... 21
9.2. Operating Conditions ................................................................................................................... 21
10. ELECTRICAL CHARACTERISTICS ............................................................................................... 22
10.1. General Parameters .................................................................................................................. 22
10.2. Analog Signal Level and Gain Parameters ............................................................................... 23
10.3. Analog Distortion and Noise Parameters .................................................................................. 24
10.4. Analog Input and Output Amplifier Parameters ......................................................................... 25
10.5. Digital I/O ................................................................................................................................... 27
10.5.1. -Law Encode Decode Characteristics ............................................................................... 27
10.5.2. A-Law Encode Decode Characteristics .............................................................................. 28
W681310
Publication Release Date: February 2015
- 5 - Revision B18
10.5.3. PCM Codes for Zero and Full Scale ................................................................................... 29
10.5.4. PCM Codes for 0dBm0 Output ........................................................................................... 29
11. TYPICAL APPLICATION CIRCUIT ................................................................................................. 30
12. PACKAGE SPECIFICATION .......................................................................................................... 32
12.1. 20L SOG (SOP)-300mil ............................................................................................................. 32
12.2. 20L SSOP-209 mil ..................................................................................................................... 33
12.3. 20L TSSOP - 4.4X6.5mm .......................................................................................................... 34
13. ORDERING INFORMATION ........................................................................................................... 35
14. VERSION HISTORY ....................................................................................................................... 36
W681310
Publication Release Date: February 2015
- 6 - Revision B18
5. PIN CONFIGURATION
20
19
18
17
16
15
14
13
12
11
SINGLE
CHANNEL
CODEC
1
2
3
4
5
6
7
8
9
10
SOG/SSOP/TSSOP
V
REF
RO
-
PAI
PAO-
PAO+
V
DD
FSR
PCMR
BCLKR
PUI
V
AG
AI+
AI-
AO
/A
V
SS
FST
PCMT
BCLKT
MCLK
20
19
18
17
16
15
14
13
12
11
SINGLE
CHANNEL
CODEC
1
2
3
4
5
6
7
8
9
10
V
RO
-
V
DD
FSR
BCLKR
V
AG
/A-Law
V
SS
BCLKT
MCLK
W681310
Publication Release Date: February 2015
- 7 - Revision B18
6. PIN DESCRIPTION
Pin
Name
Pin
No.
Functionality
VREF
1
This pin is used to bypass the on-chip VDD/2 voltage reference. It needs to be decoupled to VSS
through a 0.1 F ceramic decoupling capacitor. No external loads should be tied to this pin.
RO-
2
Inverting output of the receive smoothing filter. This pin can typically drive a 2 k load to 0.886
volt peak referenced to the analog ground level.
PAI
3
This pin is the inverting input to the power amplifier. Its DC level is at the VAG voltage.
PAO-
4
Inverting power amplifier output. The PAO- and PAO+ can drive a 300 load differentially to
1.772 volt peak referenced to the VAG voltage level.
PAO+
5
Non-inverting power amplifier output. The PAO- and PAO+ can drive a 300 load differentially
to 1.772 volt peak referenced to the VAG voltage level.
VDD
6
Power supply. This pin should be decoupled to VSS with a 0.1F ceramic capacitor.
FSR
7
8 kHz Frame Sync input for the PCM receive section. This pin also selects channel 0 or
channel 1 in the GCI and IDL modes. It can also be connected to the FST pin when transmit
and receive are synchronous operations.
PCMR
8
PCM input data receive pin. The data needs to be synchronous with the FSR and BCLKR pins.
BCLKR
9
PCM receive bit clock input pin. This pin also selects the interface mode. The GCI mode is
selected when this pin is tied to VSS. The IDL mode is selected when this pin is tied to VDD.
This pin can also be tied to the BCLKT when transmit and receive are synchronous operations.
PUI
10
Power up input signal. When this pin is tied to VDD, the part is powered up. When tied to VSS,
the part is powered down.
MCLK
11
System master clock input. Possible input frequencies are 256 kHz, 512 kHz, 1536 kHz, 1544
kHz, 2048 kHz, 2560 kHz, 4096 kHz & 4800 kHz. For a better performance, it is recommended
to have the MCLK signal synchronous and aligned to the FST signal. This is a requirement in
the case of 256 and 512 kHz frequency.
BCLKT
12
PCM transmit bit clock input pin. This pin accepts clocks of 512 kHz to 6176 kHz in the GCI
mode and 256 kHz to 4800kHz in all other PCM modes.
PCMT
13
PCM output data transmit pin. The output data is synchronous with the FST and BCLKT pins.
FST
14
8 kHz transmit frame sync input. This pin synchronizes the transmit data bytes.
W681310
Publication Release Date: February 2015
- 8 - Revision B18
Pin
Name
Pin
No.
Functionality
VSS
15
This is the supply ground. This pin should be connected to 0V.
/A-Law
16
Compander mode select pin. -Law companding is selected when this pin is tied to VDD. A-Law
companding is selected when this pin is tied to VSS.
AO
17
Analog output of the first gain stage in the transmit path.
AI-
18
Inverting input of the first gain stage in the transmit path.
AI+
19
Non-inverting input of the first gain stage in the transmit path.
VAG
20
Mid-Supply analog ground pin, which supplies a VDD/2 volt reference voltage for all-analog
signal processing. This pin should be decoupled to VSS with a 0.01F capacitor. This pin
becomes high impedance when the chip is powered down.
W681310
Publication Release Date: February 2015
- 9 - Revision B18
7. FUNCTIONAL DESCRIPTION
W681310 is a single-rail, single channel PCM CODEC for voiceband applications. The CODEC
complies with the specifications of the ITU-T G.712 recommendation. The CODEC also includes a
complete -Law and A-Law compander. The -Law and A-Law companders are designed to comply
with the specifications of the ITU-T G.711 recommendation.
The block diagram in section 3 shows the main components of the W681310. The chip consists of a
PCM interface, which can process long and short frame sync formats, as well as GCI and IDL formats.
The pre-scaler of the chip provides the internal clock signals and synchronizes the CODEC sample rate
with the external frame sync frequency. The power conditioning block provides the internal power
supply for the digital and the analog section, while the voltage reference block provides a precision
analog ground voltage for the analog signal processing. The main CODEC block diagram is shown in
section 3.
Figure 7.1 The W681310 Signal Path
7.1. Transmit Path
The A-to-D path of the CODEC contains an analog input amplifier with externally configurable gain
setting (see application examples in section 11). The device has an input operational amplifier whose
output is the input to the encoder section. If the input amplifier is not required for operation it can be
powered down and bypassed. In that case a single ended input signal can be applied to the AO pin or
the AI- pin. The AO pin becomes high input impedance when the input amplifier is powered down. The
input amplifier can be powered down by connecting the AI+ pin to VDD or VSS. The AO pin is selected as
PAO+
PAO
8
/A
-
Cont
r
AI+
AI
-
w
/A
-
Cont
r
ol
AO
+
RO
-
-
VA
G
Ant
-
Aliasi
Filter
=
3400
H
z
Ant
i
-
Aliasi
n
g
Filter
f
C
= 200
H
z
High
Pas
s
Filt
e
Smoot
hi
n
g
Filter
2
H
z
Smoot
hi
n
g
Filter
1
8
/A
Control
8
/A
-
Control
PAI
V
AG
Ant
-
Aliasing
Filter
-
Aliasing
Filter
Ant
-
Filter
High Pass
Filter
Smoothing
Filter
Filter
Smoothing
Filter
Filter
Receive Path
Transmit Path
+ -
- +
+
-
+
-
-
A/D
Converter
D/A
Converter
f
C
= 3400Hz
f
C
= 3400Hz
C
= 200Hz
f
W681310
Publication Release Date: February 2015
- 10 - Revision B18
an input when AI+ is tied to VDD and the AI- pin is selected as an input when AI+ is tied to VSS (see
Table 7.1).
AI+
Input Amplifier
Input
VDD
Powered Down
AO
1.2 to VDD-1.2
Powered Up
AI+, AI-
VSS
Powered Down
AI-
Table 7.1 Input Amplifier Modes of operation
When the input amplifier is powered down, the input signal at AO or AI- needs to be referenced to the
analog ground voltage VAG.
The output of the input amplifier is fed through a 3.4 kHz switched capacitor low pass filter to prevent
aliasing of input signals above 4 kHz, due to the sampling at 8 kHz. The output of the 3.4 kHz low pass
filter is filtered by a high pass filter with a 200 Hz cut-off frequency. The filters are designed according to
the recommendations in the G.712 ITU-T specification. From the output of the high pass filter the signal
is digitized. The signal is converted into a compressed 8-bit digital representation with either -Law or
A-Law format. The -Law or A-Law format is pin-selectable through the /A-Law pin. The compression
format can be selected according to Table 7.2.
/A-Law Pin
Format
VSS
A-Law
VDD
-Law
Table 7.2. Pin-selectable Compression Format
The digital 8-bit -Law or A-Law samples are fed to the PCM interface for serial transmission at the
sample rate supplied by the external frame sync FST.
7.2. Receive Path
The 8-bit digital input samples for the D-to-A path are serially shifted in by the PCM interface and
converted to parallel data bits. During every cycle of the frame sync FSR, the parallel data bits are fed
through the pin-selectable -Law or A-Law expander and converted to analog samples. The mode of
expansion is selected by the /A-Law pin as shown in Table 7.2. The analog samples are filtered by a
low-pass smoothing filter with a 3.4 kHz cut-off frequency, according to the ITU-T G.712 specification. A
sin(x)/x compensation is integrated with the low pass smoothing filter. The output of this filter is buffered
to provide the receive output signal RO-. The RO- output can be externally connected to the PAI pin to
provide a differential output with high driving capability at the PAO+ and PAO- pins. By using external
resistors (see section 11 for examples), various gain settings of this output amplifier can be achieved. If
the transmit power amplifier is not in use, it can be powered down by connecting PAI to VDD.
W681310
Publication Release Date: February 2015
- 11 - Revision B18
7.3. POWER MANAGEMENT
7.3.1. Analog and Digital Supply
The power supply for the analog and digital parts of the W681310 must be 2.7V to 5.25V. This supply
voltage is connected to the VDD pin. The VDD pin needs to be decoupled to ground through a 0.1 F
ceramic capacitor.
7.3.2. Analog Ground Reference Bypass
The system has an internal precision voltage reference which generates the VDD/2 mid-supply analog
ground voltage. This voltage needs to be decoupled to VSS at the VREF pin through a 0.1 F ceramic
capacitor.
7.3.3. Analog Ground Reference Voltage Outpt
The analog ground reference voltage is available for external reference at the VAG pin. This voltage
needs to be decoupled to VSS through a 0.01 F ceramic capacitor. The analog ground reference
voltage is generated from the voltage on the VREF pin and is also used for the internal signal processing.
7.4. PCM INTERFACE
The PCM interface is controlled by pins BCLKR, FSR, BCLKT & FST. The input data is received
through the PCMR pin and the output data is transmitted through the PCMT pin. The modes of
operation of the interface are shown in Table 7.3.
BCLKR
FSR
Interface Mode
64 kHz to
4.800 MHz
8 kHz
Long or Short Frame Sync
VSS
VSS
ISDN GCI with active channel B1
VSS
VDD
ISDN GCI with active channel B2
VDD
VSS
ISDN IDL with active channel B1
VDD
VDD
ISDN IDL with active channel B2
Table 7.3 PCM Interface mode selections
7.4.1. Long Frame Sync
The Long Frame Sync or Short Frame Sync interface mode can be selected by connecting the BCLKR
or BCLKT pin to a 64 kHz to 4.800 MHz clock and connecting the FSR or FST pin to the 8 kHz frame
sync. The device synchronizes the data word for the PCM interface and the CODEC sample rate on the
W681310
Publication Release Date: February 2015
- 12 - Revision B18
positive edge of the Frame Sync signal. It recognizes a Long Frame Sync when the FST pin is held
HIGH for two consecutive falling edges of the bit-clock at the BCLKT pin. The length of the Frame Sync
pulse can vary from frame to frame, as long as the positive frame sync edge occurs every 125 sec.
During data transmission in the Long Frame Sync mode, the transmit data pin PCMT will become low
impedance when the Frame Sync signal FST is HIGH or when the 8 bit data word is being transmitted.
The transmit data pin PCMT will become high impedance when the Frame Sync signal FST becomes
LOW while the data is transmitted or when half of the LSB is transmitted. The internal decision logic will
determine whether the next frame sync is a long or a short frame sync, based on the previous frame
sync pulse. To avoid bus collisions, the PCMT pin will be high impedance for two frame sync cycles
after every power down state. More detailed timing information can be found in the interface timing
section.
7.4.2. Short Frame Sync
The W681310 operates in the Short Frame Sync Mode when the Frame Sync signal at pin FST is HIGH
for one and only one falling edge of the bit-clock at the BCLKT pin. On the following rising edge of the
bit-clock, the W681310 starts clocking out the data on the PCMT pin, which will also change from high
to low impedance state. The data transmit pin PCMT will go back to the high impedance state halfway
the LSB. The Short Frame Sync operation of the W681310 is based on an 8-bit data word. When
receiving data on the PCMR pin, the data is clocked in on the first falling edge after the falling edge that
coincides with the Frame Sync signal. The internal decision logic will determine whether the next frame
sync is a long or a short frame sync, based on the previous frame sync pulse. To avoid bus collisions,
the PCMT pin will be high impedance for two frame sync cycles after every power down state. More
detailed timing information can be found in the interface timing section.
7.4.3. General Circuit Interface (GCI)
The GCI interface mode is selected when the BCLKR pin is connected to VSS for two or more frame
sync cycles. It can be used as a 2B+D timing interface in an ISDN application. The GCI interface
consists of 4 pins : FSC (FST), DCL (BCLKT), Dout (PCMT) & Din (PCMR). The FSR pin selects
channel B1 or B2 for transmit and receive. Data transitions occur on the positive edges of the data clock
DCL. The Frame Sync positive edge is aligned with the positive edge of the data clock DCLK. The data
rate is running half the speed of the bit-clock. The channels B1 and B2 are transmitted consecutively.
Therefore, channel B1 is transmitted on the first 16 clock cycles of DCL and B2 is transmitted on the
second 16 clock cycles of DCL. For more timing information, see the timing section. The GCI interface
supports bit clocks of 512 kHz to 6176 kHz for data rates of 256 kHz to 3088 kHz.
7.4.4. Interchip Digital Link (IDL)
The IDL interface mode is selected when the BCLKR pin is connected to VDD for two or more frame
sync cycles. It can be used as a 2B+D timing interface in an ISDN application. The IDL interface
consists of 4 pins : IDL SYNC (FST), IDL CLK (BCLKT), IDL TX (PCMT) & IDL RX (PCMR). The FSR
pin selects channel B1 or B2 for transmit and receive. The data for channel B1 is transmitted on the first
positive edge of the IDL CLK after the IDL SYNC pulse. The IDL SYNC pulse is one IDL CLK cycle
long. The data for channel B2 is transmitted on the eleventh positive edge of the IDL CLK after the IDL
SYNC pulse. The data for channel B1 is received on the first negative edge of the IDL CLK after the IDL
SYNC pulse. The data for channel B2 is received on the eleventh negative edge of the IDL CLK after
the IDL SYNC pulse. The transmit signal pin IDL TX becomes high impedance when not used for data
transmission and also in the time slot of the unused channel. For more timing information, see the
timing section.
W681310
Publication Release Date: February 2015
- 13 - Revision B18
7.4.5. System Timing
The system can work at 256 kHz, 512 kHz, 1536 kHz, 1544 kHz, 2048 kHz, 2560 kHz, 4096 kHz &
4800 kHz master clock rates. The system clock is supplied through the master clock input MCLK and
can be derived from the bit-clock if desired. An internal pre-scaler is used to generate a fixed 256 kHz
and 8 kHz sample clock for the internal CODEC. The pre-scaler measures the master clock frequency
versus the Frame Sync frequency and sets the division ratio accordingly. If the Frame Sync is LOW for
the entire frame sync period while the MCLK and BCLK pin clock signals are still present, the W681310
will enter the low power standby mode. Another way to power down is to set the PUI pin to LOW. When
the system needs to be powered up again, the PUI pin needs to be set to HIGH and the Frame Sync
pulse needs to be present. It will take two Frame Sync cycles before the pin PCMT will become low
impedance.
W681310
Publication Release Date: February 2015
- 14 - Revision B18
8. TIMING DIAGRAMS
Figure 8.1 Long Frame Sync PCM Timing
FST
BCLKT
D7 D6 D5 D4 D3 D2 D1PCMT
MSB LSB
THID TBCK
D0
TBCKH TBCKL
TFS
TFTFH
TFTRS
TFTRH
THID
TBDTD
TFDTD
0 1 2 3 4 5 7 8 0 1
MSB LSB
FSR
BCLKR
TBCK
D6 D5 D4 D3 D2 D1 D0PCMR D7
TDRH
TDRS
TBCKH TBCKL
TFS
TFRFH
TFRRS
TFRRH
0 1 2 3 4 5 6 7 8 0 1
6
MCLK
TFTRHM TFTRSM TMCKH TMCKL
TMCK
TRISE TFALL
TFSL
TFSL
W681310
Publication Release Date: February 2015
- 15 - Revision B18
SYMBOL
DESCRIPTION
MIN
TYP
MAX
UNIT
1/TFS
FST, FSR Frequency
---
8
---
kHz
TFSL
FST / FSR Minimum Low Width 1
TBCK
sec
1/TBCK
BCLKT, BCLKR Frequency
64
---
4800
kHz
TBCKH
BCLKT, BCLKR HIGH Pulse Width
50
---
---
ns
TBCKL
BCLKT, BCLKR LOW Pulse Width
50
---
---
ns
TFTRH
BCLKT 0 Falling Edge to FST Rising Edge Hold Time
20
---
---
ns
TFTRS
FST Rising Edge to BCLKT 1 Falling edge Setup Time
80
---
---
ns
TFTFH
BCLKT 2 Falling Edge to FST Falling Edge Hold Time
50
---
---
ns
TFDTD
FST Rising Edge to Valid PCMT Delay Time
---
---
60
ns
TBDTD
BCLKT Rising Edge to Valid PCMT Delay Time
---
---
60
ns
THID
Delay Time from the Later of FST Falling Edge, or
BCLKT 8 Falling Edge to PCMT Output High Impedance
10
---
60
ns
TFRRH
BCLKR 0 Falling Edge to FSR Rising Edge Hold Time
20
---
---
ns
TFRRS
FSR Rising Edge to BCLKR 1 Falling edge Setup Time
80
---
---
ns
TFRFH
BCLKR 2 Falling Edge to FSR Falling Edge Hold Time
50
---
---
ns
TDRS
Valid PCMR to BCLKR Falling Edge Setup Time
0
---
---
ns
TDRH
PCMR Hold Time from BCLKR Falling Edge
50
---
---
ns
Table 8.1 Long Frame Sync PCM Timing Parameters
1 TFSL must be at least TBCK
W681310
Publication Release Date: February 2015
- 16 - Revision B18
Figure 8.2 Short Frame Sync PCM Timing
D7 D6 D5 D4 D3 D2 D1
MSB LSB
TBCK
D0
TBCKH TBCKL
TFS
TFTRS
TFTRH
THID
TBDTD
0 1 2 3 4 5 6 7 8 0 1
FST
BCLKT
PCMT
TBDTD
TFTFH
-1
TFTFS
MSB LSB
TBCK
D6 D5 D4 D3 D2 D1 D0D7
TDRH
TDRS
TBCKH TBCKL
TFS
TFRRS
TFRRH
0 1 2 3 4 5 6 7 8 0 1
FSR
BCLKR
PCMR
TFRFH
-1
TFRFS
MCLK
TFTRHM TFTRSM TMCKH TMCKL
TMCK
TRISE TFALL
W681310
Publication Release Date: February 2015
- 17 - Revision B18
SYMBOL
DESCRIPTION
MIN
TYP
MAX
UNIT
1/TFS
FST, FSR Frequency
---
8
---
kHz
1/TBCK
BCLKT, BCLKR Frequency
64
---
4800
kHz
TBCKH
BCLKT, BCLKR HIGH Pulse Width
50
---
---
ns
TBCKL
BCLKT, BCLKR LOW Pulse Width
50
---
---
ns
TFTRH
BCLKT –1 Falling Edge to FST Rising Edge Hold
Time
20
---
---
ns
TFTRS
FST Rising Edge to BCLKT 0 Falling edge Setup
Time
80
---
---
ns
TFTFH
BCLKT 0 Falling Edge to FST Falling Edge Hold Time
50
---
---
ns
TFTFS
FST Falling Edge to BCLKT 1 Falling Edge Setup
Time
50
---
---
ns
TBDTD
BCLKT Rising Edge to Valid PCMT Delay Time
10
---
60
ns
THID
Delay Time from BCLKT 8 Falling Edge to PCMT
Output High Impedance
10
---
60
ns
TFRRH
BCLKR –1 Falling Edge to FSR Rising Edge Hold
Time
20
---
---
ns
TFRRS
FSR Rising Edge to BCLKR 0 Falling edge Setup
Time
80
---
---
ns
TFRFH
BCLKR 0 Falling Edge to FSR Falling Edge Hold Time
50
---
---
ns
TFRFS
FSR Falling Edge to BCLKR 1 Falling Edge Setup
Time
50
---
---
ns
TDRS
Valid PCMR to BCLKR Falling Edge Setup Time
0
---
---
ns
TDRH
PCMR Hold Time from BCLKR Falling Edge
50
---
---
ns
Table 8.2 Short Frame Sync PCM Timing Parameters
W681310
Publication Release Date: February 2015
- 18 - Revision B18
Figure 8.3 IDL PCM Timing
SYMBOL
DESCRIPTION
MIN
TYP
MAX
UNIT
1/TFS
FST Frequency
---
8
---
kHz
1/TBCK
BCLKT Frequency
256
---
4800
kHz
TBCKH
BCLKT HIGH Pulse Width
50
---
---
ns
TBCKL
BCLKT LOW Pulse Width
50
---
---
ns
TFSRH
BCLKT –1 Falling Edge to FST Rising Edge
Hold Time
20
---
---
ns
TFSRS
FST Rising Edge to BCLKT 0 Falling edge
Setup Time
60
---
---
ns
TFSFH
BCLKT 0 Falling Edge to FST Falling Edge
Hold Time
20
---
---
ns
TBDTD
BCLKT Rising Edge to Valid PCMT Delay
Time
10
---
60
ns
THID
Delay Time from the BCLKT 8 Falling Edge
(B1 channel) or BCLKT 18 Falling Edge (B2
Channel) to PCMT Output High Impedance
10
---
50
ns
TDRS
Valid PCMR to BCLKT Falling Edge Setup
Time
20
---
---
ns
TDRH
PCMR Hold Time from BCLKT Falling Edge
75
---
---
ns
Table 8.3 IDL PCM Timing Parameters
FST
BCLKT
PCMT
PCMR
D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0
D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
TFS
TFSRH
TFSFH
TFSRS
TBDTD TBDTD TBDTD TBDTD
THID THID
TDRS TDRS
TDRH TDRH
BCH = 0
B1 Channel
BCH = 1
B2 Channel
MSB
MSB
MSB
MSB
LSB
LSB
LSB
LSB
TBCK
TBCKH TBCKL
-1
W681310
Publication Release Date: February 2015
- 19 - Revision B18
Figure 8.4 GCI PCM Timing
SYMBOL
DESCRIPTION
MIN
TYP
MAX
UNIT
1/TFST
FST Frequency
---
8
---
kHz
1/TBCK
BCLKT Frequency
512
---
6176
kHz
TBCKH
BCLKT HIGH Pulse Width
50
---
---
ns
TBCKL
BCLKT LOW Pulse Width
50
---
---
ns
TFSRH
BCLKT 0 Falling Edge to FST Rising Edge Hold Time
20
---
---
ns
TFSRS
FST Rising Edge to BCLKT 1 Falling edge Setup Time
60
---
---
ns
TFSFH
BCLKT 1 Falling Edge to FST Falling Edge Hold Time
20
---
---
ns
TFDTD
FST Rising Edge to Valid PCMT Delay Time
---
---
60
ns
TBDTD
BCLKT Rising Edge to Valid PCMT Delay Time
---
---
60
ns
THID
Delay Time from the BCLKT 16 Falling Edge (B1
channel) or BCLKT 32 Falling Edge (B2 Channel) to
PCMT Output High Impedance
10
---
50
ns
TDRS
Valid PCMR to BCLKT Rising Edge Setup Time
20
---
---
ns
TDRH
PCMR Hold Time from BCLKT Rising Edge
---
---
60
ns
Table 8.4 GCI PCM Timing Parameters
FST
BCLKT
PCMT
PCMR
D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0
D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0
TFS
TFDTD TBDTD TBDTD TBDTD
THID THID
TDRS TDRS
TDRH TDRH
BCH = 0
B1 Channel
BCH = 1
B2 Channel
MSB
MSB
MSB
MSB
LSB
LSB
LSB
LSB
TFSRH
TFSFH
TFSRS
TBCK
TBCKH TBCKL
2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 3410
W681310
Publication Release Date: February 2015
- 20 - Revision B18
SYMBOL
DESCRIPTION
MIN
TYP
MAX
UNIT
1/TMCK
Master Clock Frequency
---
256
512
1536
1544
2048
2560
4096
4800
---
kHz
TMCKH /
TMCK
MCLK Duty Cycle for 256 kHz
Operation
45%
55%
TMCKH
Minimum Pulse Width HIGH for
MCLK(512 kHz or Higher)
50
---
---
ns
TMCKL
Minimum Pulse Width LOW for MCLK
(512 kHz or Higher)
50
---
---
ns
TFTRHM
MCLK falling Edge to FST Rising Edge
Hold Time
50
---
---
ns
TFTRSM
FST Rising Edge to MCLK Falling edge
Setup Time
50
---
---
ns
TRISE
Rise Time for All Digital Signals
---
---
50
ns
TFALL
Fall Time for All Digital Signals
---
---
50
ns
Table 8.5 General PCM Timing Parameters
W681310
Publication Release Date: February 2015
- 21 - Revision B18
9. ABSOLUTE MAXIMUM RATINGS
9.1. ABSOLUTE MAXIMUM RATINGS
Condition
Value
Junction temperature
1500C
Storage temperature range
-650C to +1500C
Voltage Applied to any pin
(VSS - 0.3V) to (VDD + 0.3V)
Voltage applied to any pin (Input current limited to +/-20 mA)
(VSS – 1.0V) to (VDD + 1.0V)
VDD - VSS
-0.5V to +6V
1. Stresses above those listed may cause permanent damage to the device. Exposure to the absolute
maximum ratings may affect device reliability. Functional operation is not implied at these conditions.
9.2. OPERATING CONDITIONS
Condition
Value
Industrial operating temperature
-400C to +850C
Supply voltage (VDD)
+2.7V to +5.25V
Ground voltage (VSS)
0V
Note: Exposure to conditions beyond those listed under Absolute Maximum Ratings may adversely
affect the life and reliability of the device.
W681310
Publication Release Date: February 2015
- 22 - Revision B18
10. ELECTRICAL CHARACTERISTICS
10.1. GENERAL PARAMETERS
Symbol
Parameters
Conditions
Min (2)
Typ (1)
Max (2)
Units
VIL
Input LOW Voltage
0.6
V
VIH
Input HIGH Voltage
2.2
V
VOL
PCMT Output LOW Voltage
IOL = 1.6 mA
0.4
V
VOH
PCMT Output HIGH Voltage
IOL = -1.6 mA
VDD –
0.5
V
IDD
VDD Current (Operating) - ADC + DAC
No Load
3.3
5
mA
ISB
VDD Current (Standby)
FST & FSR =Vss ;
PUI=VDD
10
100
A
Ipd
VDD Current (Power Down)
PUI= Vss
0.1
10
A
IIL
Input Leakage Current
VSS<VIN<VDD
-10
+10
A
IOL
PCMT Output Leakage Current
VSS<PCMT<VDD
High Z State
-10
+10
A
CIN
Digital Input Capacitance
10
pF
COUT
PCMT Output Capacitance
PCMT High Z
15
pF
1. Typical values: TA = 25°C , VDD = 3.0 V
2. All min/max limits are guaranteed by Nuvoton via electrical testing or characterization. Not all specifications
are 100 percent tested.
W681310
Publication Release Date: February 2015
- 23 - Revision B18
10.2. ANALOG SIGNAL LEVEL AND GAIN PARAMETERS
VDD=2.7V to 3.6V; VSS=0V; TA=-40C to +85C; all analog signals referred to VAG; MCLK=BCLK= 2.048 MHz;
FST=FSR=8kHz Synchronous operation.
PARAMETER
SYM.
CONDITION
TYP.
TRANSMIT
(A/D)
RECEIVE
(D/A)
UNIT
MIN.
MAX.
MIN.
MAX.
Absolute Level
LABS
0 dBm0 = -5dBm @ 600
0.616
0.436
---
---
---
---
VPK
VRMS
Max. Transmit Level
TXMAX
3.17 dBm0 for -Law
3.14 dBm0 for A-Law
0.8873
0.8843
---
---
---
---
---
---
---
---
VPK
VPK
Absolute Gain (0
dBm0 @ 1020 Hz;
TA=+25C)
GABS
0 dBm0 @ 1020 Hz;
TA=+25C
0
-0.20
+0.20
-0.20
+0.20
dB
Absolute Gain
variation with
Temperature
GABST
TA=0C to TA=+70C
TA=-40C to TA=+85C
0
-0.05
-0.10
+0.05
+0.10
-0.05
-0.10
+0.05
+0.10
dB
Frequency
Response,
Relative to 0dBm0 @
1020 Hz
GRTV
15 Hz
50 Hz
60 Hz
200 Hz
300 to 3000 Hz
3300 Hz
3400 Hz
3600 Hz
4000 Hz
4600 Hz to 100 kHz
---
---
---
---
---
---
---
---
---
---
---
---
---
-1.4
-0.15
-0.35
-0.8
---
---
---
-40
-30
-26
-0.4
+0.2
+0.2
+0.1
0
-14
-32
-0.5
-0.5
-0.5
-0.5
-0.20
-0.4
-0.8
---
---
---
0
0
0
0
+0.2
+0.15
0
0
-14
-30
dB
Gain Variation vs.
Level Tone
(1020 Hz relative to –
10 dBm0)
GLT
+3 to –40 dBm0
-40 to –50 dBm0
-50 to –55 dBm0
---
---
---
-0.3
-0.6
-1.6
+0.3
+0.6
+1.6
-0.2
-0.4
-1.6
+0.2
+0.4
+1.6
dB
W681310
Publication Release Date: February 2015
- 24 - Revision B18
10.3. ANALOG DISTORTION AND NOISE PARAMETERS
VDD=2.7V to 3.6V; VSS=0V; TA=-40C to +85C; all analog signals referred to VAG; MCLK=BCLK= 2.048 MHz
FST=FSR=8kHz Synchronous operation.
PARAMETER
SYM.
CONDITION
TRANSMIT (A/D)
RECEIVE (D/A)
UNIT
MIN.
TYP.
MAX.
MIN.
TYP.
MAX.
Total Distortion vs.
Level Tone (1020 Hz,
-Law, C-Message
Weighted)
DLT
+3 dBm0
0 dBm0 to -30 dBm0
-40 dBm0
-45 dBm0
34
35
30
25
---
---
---
---
---
---
---
---
34
36
30
25
---
---
---
---
---
---
---
---
dBC
Total Distortion vs.
Level Tone (1020 Hz,
A-Law, Psophometric
Weighted)
DLTA
-3 dBm0
-6 dBm0 to -27 dBm0
-34 dBm0
-40 dBm0
-55 dBm0
30
35
34.5
28.5
13.5
---
---
---
---
---
---
---
---
30
36
34.2
30
15
---
---
---
---
---
---
---
---
dBp
Spurious Out-Of-Band
at RO- (300 Hz to
3400 Hz @ 0dBm0)
DSPO
4600 Hz to 7600 Hz
7600 Hz to 8400 Hz
8400 Hz to 100000 Hz
---
---
---
---
---
---
---
---
---
---
---
---
---
---
---
-30
-40
-30
dB
Spurious In-Band (700
Hz to 1100 Hz @
0dBm0)
DSPI
300 to 3000 Hz
---
---
-47
---
---
-47
dB
Intermodulation
Distortion (300 Hz to
3400 Hz –4 to –21
dBm0
DIM
Two tones
---
---
-41
---
---
-41
dB
Crosstalk (1020 Hz @
0dBm0)
DXT
---
---
-75
---
---
-75
dBm0
Absolute Group Delay
ABS
1200Hz
---
---
360
---
---
240
sec
Group Delay
Distortion (relative to
group delay @ 1200
Hz)
D
500 Hz
600 Hz
1000 Hz
2600 Hz
2800 Hz
---
---
---
---
---
---
---
---
---
---
750
380
130
130
750
---
---
---
---
---
---
---
---
---
---
750
370
120
120
750
sec
Idle Channel Noise
NIDL
-Law; C-message
A-Law; Psophometric
---
---
---
---
22
-68
---
---
---
---
15
-75
dBrnc0
dBm0p
W681310
Publication Release Date: February 2015
- 25 - Revision B18
10.4. ANALOG INPUT AND OUTPUT AMPLIFIER PARAMETERS
VDD=2.7V to 3.6V; VSS=0V; TA=-40C to +85C; all analog signals referred to VAG;
PARAMETER
SYM.
CONDITION
MIN.
TYP.
MAX.
UNIT.
AI Input Offset Voltage
VOFF,AI
AI+, AI-
---
---
25
mV
AI Input Current
IIN,AI
AI+, AI-
---
0.1
1.0
A
AI Input Resistance
RIN,AI
AI+, AI- to VAG
10
---
---
M
AI Input Capacitance
CIN,AI
AI+, AI-
---
---
10
pF
AI Common Mode Input
Voltage Range
VCM,AI
AI+, AI-
1.2
---
VDD-1.2
V
AI Common Mode Rejection
Ratio
CMRRTI
AI+, AI-
---
60
---
dB
AI Amp Gain Bandwidth
Product
GBWTI
AO, RLD10k
---
2150
---
kHz
AI Amp DC Open Loop Gain
GTI
AO, RLD10k
---
95
---
dB
AI Amp Equivalent Input Noise
NTI
C-Message Weighted
---
-24
---
dBrnC
AO Output Voltage Range
VTG
RLD=2k to VAG
0.4
---
VDD-0.4
V
Load Resistance
RLDTGRO
AO, RO to VAG
2
---
---
k
Load Capacitance
CLDTGRO
AO, RO
---
---
200
pF
AO & RO Output Current
IOUT1
0.5 AO,RO- VDD-0.5
1.0
---
---
mA
RO- Output Resistance
RRO-
RO-, 0 to 3400 Hz
---
1
---
RO- Output Offset Voltage
VOFF,RO-
RO- to VAG
---
---
25
mV
Analog Ground Voltage
VAG
Relative to VSS
VDD/2-0.1
VDD/2
VDD/2+0.
1
V
VAG Output Resistance
RVAG
Within 25mV change
---
12.5
25
Power Supply Rejection Ratio
(0 to 100 kHz to VDD, C-
message)
PSRR
Transmit
Receive
40
40
60
60
---
---
dBC
PAI Input Offset Voltage
VOFF,PAI
PAI
---
---
25
mV
PAI Input Current
IIN,PAI
PAI
---
0.05
1.0
A
W681310
Publication Release Date: February 2015
- 26 - Revision B18
PARAMETER
SYM.
CONDITION
MIN.
TYP.
MAX.
UNIT.
PAI Input Resistance
RIN,PAI
PAI to VAG
10
---
---
M
PAI Amp Gain Bandwidth
Product
GBWPI
PAO- no load
---
1000
---
kHz
Output Offset Voltage
VOFF,PO
PAO+ to PAO-
---
---
50
mV
Load Resistance
RLDPO
PAO+, PAO-
differentially
300
---
---
Load Capacitance
CLDPO
PAO+, PAO-
differentially
---
---
1000
pF
PAO Output Current
IOUTPAO
0.4 PAO+,PAO--
VDD-0.4
6.0
---
---
mA
PAO Output Resistance
RPAO
PAO+ to PAO-
---
1
---
PAO Differential Gain
GPAO
RLD=300, +3dBm0, 1
kHz, PAO+ to PAO-
-0.2
0
+0.2
dB
PAO Differential Signal to
Distortion C-Message
weighted
DPAO
ZLD=300
ZLD=100nF + 20
ZLD=100nF + 100
45
---
---
60
40
40
---
---
---
dBC
PAO Power Supply Rejection
Ratio (0 to 25 kHz to VDD,
Differential out)
PSRRP
AO
0 to 4 kHz
4 to 25 kHz
40
---
55
40
---
---
dB
W681310
Publication Release Date: February 2015
- 27 - Revision B18
10.5. DIGITAL I/O
10.5.1. -Law Encode Decode Characteristics
Normalized
Encode
Decision
Levels
Digital Code
Normalized
Decode
Levels
D7
D6
D5
D4
D3
D2
D1
D0
Sign
Chord
Chord
Chord
Step
Step
Step
Step
8159
7903
:
4319
4063
:
2143
2015
:
1055
991
:
511
479
:
239
223
:
103
95
:
35
31
:
3
1
0
1
0
0
0
0
0
0
0
8031
:
1
0
0
0
1
1
1
1
4191
:
1
0
0
1
1
1
1
1
2079
:
1
0
1
0
1
1
1
1
1023
:
1
0
1
1
1
1
1
1
495
:
1
1
0
0
1
1
1
1
231
:
1
1
0
1
1
1
1
1
99
:
1
1
1
0
1
1
1
1
33
:
1
1
1
1
1
1
1
0
2
1
1
1
1
1
1
1
1
0
Notes:
Sign bit = 0 for negative values, sign bit = 1 for positive values
W681310
Publication Release Date: February 2015
- 28 - Revision B18
10.5.2. A-Law Encode Decode Characteristics
Normalized
Encode
Decision
Levels
Digital Code
Normalized
Decode
Levels
D7
D6
D5
D4
D3
D2
D1
D0
Sign
Chord
Chord
Chord
Step
Step
Step
Step
4096
3968
:
2048
2048
:
1088
1024
:
544
512
:
272
256
:
136
128
:
68
64
:
2
0
1
0
1
0
1
0
1
0
4032
:
1
0
1
0
0
1
0
1
2112
:
1
0
1
1
0
1
0
1
1056
:
1
0
0
0
0
1
0
1
528
:
1
0
0
1
0
1
0
1
264
:
1
1
1
0
0
1
0
1
132
:
1
1
1
0
0
1
0
1
66
:
1
1
0
1
0
1
0
1
1
Notes:
1. Sign bit = 0 for negative values, sign bit = 1 for positive values
2. Digital code includes inversion of all even number bits
W681310
Publication Release Date: February 2015
- 29 - Revision B18
10.5.3. PCM Codes for Zero and Full Scale
Level
-Law
A-Law
Sign bit
(D7)
Chord bits
(D6,D5,D4)
Step bits
(D3,D2,D1,D0)
Sign bit
(D7)
Chord bits
(D6,D5,D4)
Step bits
(D3,D2,D1,D0)
+ Full Scale
1
000
0000
1
010
1010
+ Zero
1
111
1111
1
101
0101
- Zero
0
111
1111
0
101
0101
- Full Scale
0
000
0000
0
010
1010
10.5.4. PCM Codes for 0dBm0 Output
Sample
-Law
A-Law
Sign bit
(D7)
Chord bits
(D6,D5,D4)
Step bits
(D3,D2,D1,D0)
Sign bit
(D7)
Chord bits
(D6,D5,D4)
Step bits
(D3,D2,D1,D0)
1
0
001
1110
0
011
0100
2
0
000
1011
0
010
0001
3
0
000
1011
0
010
0001
4
0
001
1110
0
011
0100
5
1
001
1110
1
011
0100
6
1
000
1011
1
010
0001
7
1
000
1011
1
010
0001
8
1
001
1110
1
011
0100
W681310
Publication Release Date: February 2015
- 30 - Revision B18
11. TYPICAL APPLICATION CIRCUIT
+
0.01 uF
27K
-
PCM OUT
1.0 uF 8 KHz Frame Sync
DIFFERENTIAL
AUDIO IN
PCM IN
-
0.1 uF
DIFFERENTIAL
AUDIO OUT
RL > 150 ohms
POWER CONTROL
27K
1.0 uF 27K
0.1 uF
2.048 MHz
Bit Clock
MODE SELECT
27K U2
W681310
615
10
16
14
12
13
11
8
9
7
17
18
19
20
1
2
5
3
4
VDDVSS
PUI
u/A
FST
BCLKT
PCMT
MCLK
PCMR
BCLKR
FSR
AO
AI-
AI+
VAG
VREF
RO-
PAO+
PAI
PAO-
+27K
27K
VDD
Figure 11.1 Typical circuit for Differential Analog I/O’s
AUDIO OUT
RL > 2K ohms
1.0 uF
27K
AUDIO IN
U3
W681310
615
10
16
14
12
13
11
8
9
7
17
18
19
20
1
2
5
3
4
VDDVSS
PUI
u/A
FST
BCLKT
PCMT
MCLK
PCMR
BCLKR
FSR
AO
AI-
AI+
VAG
VREF
RO-
PAO+
PAI
PAO-
27K
PCM IN
8 KHz Frame Sync
27K
PCM OUT
MODE SELECT
100 uF
VDD
0.1 uF0.01 uF
27K
POWER CONTROL
1.0 uF
0.1 uF
2.048 MHz
Bit Clock
27K
AUDIO OUT
RL > 150 ohms
27K
Figure 11.2 Typical circuit for Single Ended Analog I/O’s
W681310
Publication Release Date: February 2015
- 31 - Revision B18
100pF 8 KHz Frame Sync
POWER CONTROL
62k
2.048 MHz
Bit Clock
1.0 uF
3.9K
MICROPHONE
+
27K
3.9K
VDD
27K
0.1 uF
0.01 uF
1K
SPEAKER
0.1 uF
1.0 uF
22 uF
27K
100pF
U4
W681310
615
10
16
14
12
13
11
8
9
7
17
18
19
20
1
2
5
3
4
VDDVSS
PUI
u/A
FST
BCLKT
PCMT
MCLK
PCMR
BCLKR
FSR
AO
AI-
AI+
VAG
VREF
RO-
PAO+
PAI
PAO-
1.5K
PCM OUT
1.5K
62K
ELECTRET
PCM IN
MODE SELECT
Figure 11.3 Handset Interface
0.1 uF
27K
600
0.01 uF
TRANSFORMER B1/B2 SELECT
U5
W681310
615
10
16
14
12
13
11
8
9
7
17
18
19
20
1
2
5
3
4
VDDVSS
PUI
u/A
FST
BCLKT
PCMT
MCLK
PCMR
BCLKR
FSR
AO
AI-
AI+
VAG
VREF
RO-
PAO+
PAI
PAO-
27K
PCM OUT
27K600 OHM 1:1 MODE SELECT
VDD
27K
0.1 uF
POWER CONTROL
4.096 MHz
Bit Clock
8 KHz Frame Sync
PCM IN
1.0 uF
Figure 11.4 Transformer Interface Circuit in GCI mode
W681310
Publication Release Date: February 2015
- 32 - Revision B18
12. PACKAGE SPECIFICATION
12.1. 20L SOG (SOP)-300MIL
SMALL OUTLINE PACKAGE (SAME AS SOG & SOIC) DIMENSIONS
SYMBOL
DIMENSION (MM)
DIMENSION (INCH)
MIN.
MAX.
MIN.
MAX.
A
2.35
2.65
0.093
0.104
A1
0.10
0.30
0.004
0.012
b
0.33
0.51
0.013
0.020
c
0.23
0.32
0.009
0.013
E
7.40
7.60
0.291
0.299
D
12.60
13.00
0.496
0.512
e
1.27 BSC
0.050 BSC
HE
10.00
10.65
0.394
0.419
Y
-
0.10
-
0.004
L
0.40
1.27
0.016
0.050
0
0º
8º
0º
8º
E
1
2
0
1
1
1
0
W681310
Publication Release Date: February 2015
- 33 - Revision B18
12.2. 20L SSOP-209 MIL
SHRINK SMALL OUTLINE PACKAGE DIMENSIONS
SYMBOL
DIMENSION (MM)
DIMENSION (INCH)
MIN.
NOM.
MAX.
MIN.
NOM.
MAX.
A
-
-
2.00
-
-
0.079
A1
0.05
-
-
0.002
-
-
A2
1.65
1.75
1.85
0.065
0.069
-
b
0.22
-
0.38
0.009
-
0.015
c
0.09
-
0.25
0.004
-
0.010
D
6.90
7.20
7.50
0.272
0.283
0.295
E
5.00
5.30
5.60
0.197
0.209
0.220
HE
7.40
7.80
8.20
0.291
0.307
0.323
e
-
0.65
-
-
0.0256
-
L
0.55
0.75
0.95
0.021
0.030
0.037
L1
-
1.25
-
-
0.050
-
Y
-
-
0.10
-
-
0.004
0
0º
-
8º
0
-
8º
1
2
0
D
E
e
Y
b
A
1
A
2
A
SEATING
PLANE
DTEAIL
A
L
L
1
DETAIL
A
SEATING
PLANE
E
H
1
0
1
1
b
W681310
Publication Release Date: February 2015
- 34 - Revision B18
12.3. 20L TSSOP - 4.4X6.5MM
PLASTIC THIN SHRINK SMALL OUTLINE PACKAGE (TSSOP) DIMENSIONS
W681310
Publication Release Date: February 2015
- 35 - Revision B18
13. ORDERING INFORMATION
Nuvoton Part Number Description
When ordering W681310 series devices, please refer to the following part numbers.
Part Number
W681310SG
W681310RG
W681310WG
Package Type:
S = 20-Lead Plastic Small Outline Package (SOG/SOP)
R = 20-Lead Plastic Small Outline Package (SSOP)
WG = 20-Lead Free Plastic Thin Small Outline Package (TSSOP)
Product Family
W681310 Product
W681310_ _
Package Material:
G = Pb-free Package
W681310
Publication Release Date: February 2015
- 36 - Revision B18
14. VERSION HISTORY
VERSION
DATE
PAGE
DESCRIPTION
B12
April, 2005
36
Add Important Notice
B13
September,
2005
29,30
22
Various
Improved Application Diagram
Added Reference to VRMS
Capitalized logic HIGH/LOW
B14
April, 2007
31
33
35
36
36
SOP Package diagram legible
SSOP Package diagram legible
TSSOP Package diagram legible
Removed Pb TSSOP Package
Footnote on Pb parts limited availability
B15
January 2009
22
Idle Channel Noise (-Law; C-message) value updated
B16
January 2009
34
Leaded packages no longer supported
B17
January 2010
34
Improved TSSOP package diagram
B18
February 2015
24
Update the TRANSMIT parameter
Important Notice
Nuvoton Products are neither intended nor warranted for usage in systems or equipment, any
malfunction or failure of which may cause loss of human life, bodily injury or severe property
damage. Such applications are deemed, “Insecure Usage”.
Insecure usage includes, but is not limited to: equipment for surgical implementation, atomic
energy control instruments, airplane or spaceship instruments, the control or operation of
dynamic, brake or safety systems designed for vehicular use, traffic signal instruments, all
types of safety devices, and other applications intended to support or sustain life.
All Insecure Usage shall be made at customer’s risk, and in the event that third parties lay
claims to Nuvoton as a result of customer’s Insecure Usage, customer shall indemnify the
damages and liabilities thus incurred by Nuvoton.