a FEATURES Operates from +1.7 V to 618 V Low Supply Current: 15 mA/Amplifier Low Offset Voltage: 75 mV Outputs Sink and Source: 68 mA No Phase Reversal Single or Dual Supply Operation High Open-Loop Gain: 600 V/mV Unity-Gain Stable Precision, Micropower Operational Amplifiers OP193/OP293/OP493* PIN CONFIGURATIONS 8-Lead SO (S Suffix) 8-Lead Epoxy DIP (P Suffix) NULL NC -IN A +IN A V+ OP193 OUT A NULL V- NULL 1 8 NC -IN A 2 7 V+ +IN A 3 6 OUT A 4 5 NULL V- APPLICATIONS Digital Scales Strain Gages Portable Medical Equipment Battery Powered Instrumentation Temperature Transducer Amplifier GENERAL DESCRIPTION The OP193 family of single-supply operational amplifiers features a combination of high precision, low supply current and the ability to operate at low voltages. For high performance in single supply systems the input and output ranges include ground, and the outputs swing from the negative rail to within 600 mV of the positive supply. For low voltage operation the OP193 family can operate down to 1.7 volts or 0.85 volts. The combination of high accuracy and low power operation make the OP193 family useful for battery powered equipment. Its low current drain and low voltage operation allow it to continue performing long after other amplifiers have ceased functioning either because of battery drain or headroom. The OP193 family is specified for single +2 volt through dual 15 volt operation over the HOT (-40C to +125C) temperature range. They are available in plastic DIPs, plus SOIC surface mount packages. OP193 NC = NO CONNECT 8-Lead SO (S Suffix) OUT A -IN A +IN A 8-Lead Epoxy DIP (P Suffix) V+ OP293 V- OUT B OUT A 1 7 OUT B +IN B +IN A 3 6 -IN B 5 +IN B 4 16-Lead Wide Body SOL (S Suffix) OUT A 1 14 OUT D -IN A 2 13 -IN D 12 +IN D OP493 V+ -IN A 2 14-Lead Epoxy DIP (P Suffix) V+ 4 8 -IN B V- +IN A 3 OP293 11 V- +IN B 5 10 +IN C -IN B 6 9 -IN C OUT B 7 8 OUT C OUT A -IN A +IN A V+ +IN B -IN B OUT B NC OP493 OUT D -IN D +IN D V- +IN C -IN C OUT C NC NC = NO CONNECT *Patent pending. REV. A Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. (c) Analog Devices, Inc., 1996 One Technology Way, P.O. Box 9106, Norwood. MA 02062-9106, U.S.A. Tel: 617/329-4700 Fax: 617/326-8703 OP193/OP293/OP493-SPECIFICATIONS ELECTRICAL SPECIFICATIONS (@ V = 615.0 V, T = +258C unless otherwise noted) S A "E" Grade Min Typ Max Parameter Symbol Conditions INPUT CHARACTERISTICS Offset Voltage VOS OP193 OP193, -40C TA +125C OP293 OP293, -40C TA +125C OP493 OP493, -40C TA +125C VCM = 0 V, -40C TA +125C VCM = 0 V, -40C TA +125C Input Bias Current IB Input Offset Current IOS Input Voltage Range Common-Mode Rejection VCM CMRR Large Signal Voltage Gain AVO Large Signal Voltage Gain Large Signal Voltage Gain Long Term Offset Voltage Offset Voltage Drift OUTPUT CHARACTERISTICS Output Voltage Swing High Output Voltage Swing Low Short Circuit Current POWER SUPPLY Power Supply Rejection Ratio Supply Current/Amplifier NOISE PERFORMANCE Voltage Noise Density Current Noise Density Voltage Noise DYNAMIC PERFORMANCE Slew Rate Gain Bandwidth Product Channel Separation AVO AVO VOS VOS/T VOH VOL -14.9 VCM +14 V -14.9 VCM +14 V, -40C TA +125C RL = 100 k, -10 V VOUT +10 V -40C TA +85C -40C TA +125C RL = 10 k, -10 V VOUT +10 V -40C TA +85C -40C TA +125C RL = 2 k, -10 V VOUT +10 V -40C TA +85C -40C TA +125C Note 1 Note 2 IL = 1 mA IL = 1 mA, -40C TA +125C IL = 5 mA IL = -1 mA IL = -1 mA, -40C TA +125C IL = -5 mA -14.9 100 ISY VS = 1.5 V to 18 V VS = 1.5 V to 18 V, -40C TA +125C -40C TA +125C, RL = VOUT = 0 V, VS = 18 V Units 75 175 100 200 125 225 150 250 250 350 275 375 V V V V V V 15 20 nA 4 +13.5 nA V dB 2 +13.5 116 -14.9 97 116 97 94 dB 500 300 500 300 300 V/mV V/mV V/mV 150 V/mV V/mV V/mV 300 350 200 350 200 150 200 125 200 125 100 0.2 100 150 1.75 300 V/mV V/mV V/mV V V/C +14.1 14.2 +14.1 14.2 V +14.0 +13.9 14.1 -14.7 -14.6 +14.0 +13.9 14.1 -14.7 -14.6 V V V -14.4 14.2 -14.1 25 -14.4 14.2 -14.1 25 V V mA 120 dB ISC PSRR "F" Grade Min Typ Max 100 120 97 97 94 dB 30 30 A en in en p-p f = 1 kHz f = 1 kHz 0.1 Hz to 10 Hz 65 0.05 3 65 0.05 3 nV/Hz pA/Hz V p-p SR GBP RL = 2 k 15 35 15 35 V/ms kHz 120 120 dB VOUT = 10 V p-p, RL = 2 k, f = 1 kHz NOTES 1 Long term offset voltage is guaranteed by a 1000 hour life test performed on three independent lots at +125 C, with an LTPD of 1.3. 2 Offset voltage drift is the average of the -40C to +25C delta and the +25C to +125C delta. Specifications subject to change without notice. -2- REV. A OP193/OP293/OP493 ELECTRICAL SPECIFICATIONS (@ V = +5.0 V, V S CM = 0.1 V, TA = +258C unless otherwise noted) "E" Grade Min Typ Max Parameter Symbol Conditions INPUT CHARACTERISTICS Offset Voltage VOS OP193 OP193, -40C TA +125C OP293 OP293, -40C TA +125C OP493 OP493, -40C TA +125C -40C TA +125C -40C TA +125C Input Bias Current Input Offset Current Input Voltage Range Common-Mode Rejection IB IOS VCM CMRR Large Signal Voltage Gain AVO Large Signal Voltage Gain Long Term Offset Voltage Offset Voltage Drift OUTPUT CHARACTERISTICS Output Voltage Swing High Output Voltage Swing Low Short Circuit Current POWER SUPPLY Power Supply Rejection Ratio AVO VOS VOS/T VOH VOL 0.1 VCM +4 V 0.1 VCM +4 V, -40C TA +125C RL = 100 k, 0.03 VOUT +4.0 V -40C TA +85C -40C TA +125C RL = 10 k, 0.03 VOUT +4.0 V -40C TA +85C -40C TA +125C Note 1 Note 2 IL = 100 A IL = 1 mA IL = 1 mA, -40C TA +125C IL = 5 mA IL = -100 A IL = -100 A, -40C TA +125C No Load IL = -1 mA IL = -1 mA, -40C TA +125C IL = -5 mA 0 100 75 175 100 200 125 225 15 2 4 116 "F" Grade Min Typ Max 0 96 150 250 250 350 275 375 20 4 4 116 Units V V V V V V nA nA V dB 92 92 dB 200 125 200 125 V/mV V/mV V/mV 130 130 75 50 75 50 70 0.2 70 150 1.25 300 V/mV V/mV V/mV V V/C 4.4 +4.1 4.4 4.4 +4.1 4.4 V V +4.0 +4.0 4.4 140 +4.0 +4.0 4.4 140 V V mV 160 220 5 280 700 8 ISC 160 220 5 280 400 500 900 700 8 400 500 900 mV mV mV mV mV mA ISY VS = 1.7 V to 6.0 V VS = 1.5 V to 18 V, -40C TA +125C VCM = 2.5 V, RL = NOISE PERFORMANCE Voltage Noise Density Current Noise Density Voltage Noise en in en p-p f = 1 kHz f = 1 kHz 0.1 Hz to 10 Hz 65 0.05 3 65 0.05 3 nV/Hz pA/Hz V p-p DYNAMIC PERFORMANCE Slew Rate Gain Bandwidth Product SR GBP RL = 2 k 12 35 12 35 V/ms kHz Supply Current/Amplifier PSRR 100 120 120 dB 14.5 14.5 dB A 94 97 90 NOTES 1 Long term offset voltage is guaranteed by a 1000 hour life test performed on three independent lots at +125 C, with an LTPD of 1.3. 2 Offset voltage drift is the average of the -40C to +25C delta and the +25C to +125C delta. Specifications subject to change without notice. REV. A -3- OP193/OP293/OP493 ELECTRICAL SPECIFICATIONS (@ VS = +3.0 V, VCM = 0.1 V, TA = +258C unless otherwise noted) "E" Grade Min Typ Max Parameter Symbol Conditions INPUT CHARACTERISTICS Offset Voltage VOS OP193 OP193, -40C TA +125C OP293 OP293, -40C TA +125C OP493 OP493, -40C TA +125C -40C TA +125C -40C TA +125C Input Bias Current Input Offset Current Input Voltage Range Common-Mode Rejection Large Signal Voltage Gain Long Term Offset Voltage Offset Voltage Drift OUTPUT CHARACTERISTICS Output Voltage Swing High Output Voltage Swing Low Short Circuit Current POWER SUPPLY Power Supply Rejection Ratio IB IOS VCM CMRR V V V V V V nA nA V dB 90 100 75 VOH IL = 1 mA IL = 1 mA, -40C TA +125C IL = 5 mA IL = -1 mA IL = -1 mA -40C TA +125C IL = -5 mA +2.1 2.14 +2.1 2.14 V 1.9 +1.9 2.1 280 1.9 +1.9 2.1 280 V V mV VS = +1.7 V to +6 V, -40C TA +125C VCM = 1.5 V, RL = -40C TA +125C 100 94 VOL PSRR Supply Voltage Range VS 116 0.2 700 8 +2 116 87 100 75 100 ISC ISY DYNAMIC PERFORMANCE Slew Rate Gain Bandwidth Product Channel Separation 0 94 150 250 250 350 275 375 20 4 2 Units 0.1 VCM +2 V 0.1 VCM +2 V, -40C TA +125C AVO RL = 100 k, 0.03 VOUT 2 V -40C TA +85C -40C TA +125C VOS Note 1 VOS/T Note 2 Supply Current/Amplifier NOISE PERFORMANCE Voltage Noise Density Current Noise Density Voltage Noise 0 97 75 175 100 200 125 225 15 2 2 "F" Grade Min Typ Max 100 150 1.25 400 300 500 900 700 8 400 500 900 97 90 14.5 22 22 18 +2 dB V/mV V/mV V/mV V V/C mV mV mA 14.5 22 22 18 dB A A V en in en p-p f = 1 kHz f = 1 kHz 0.1 Hz to 10 Hz 65 0.05 3 65 0.05 3 nV/Hz pA/Hz V p-p SR GBP RL = 2 k 10 25 10 25 V/ms kHz 120 120 dB VOUT = 10 V p-p, RL = 2 k, f = 1 kHz NOTES 1 Long term offset voltage is guaranteed by a 1000 hour life test performed on three independent lots at +125 C, with an LTPD of 1.3. 2 Offset voltage drift is the average of the -40C to +25C delta and the +25C to +125C delta. Specifications subject to change without notice. -4- REV. A OP193/OP293/OP493 ELECTRICAL SPECIFICATIONS (@ V = +2.0 V, V S CM = 0.1 V, TA = +258C unless otherwise noted) "E" Grade Min Typ Max Parameter Symbol Conditions INPUT CHARACTERISTICS Offset Voltage VOS Input Bias Current Input Offset Current Input Voltage Range Large Signal Voltage Gain IB IOS VCM AVO OP193 OP193, -40C TA +125C OP293 OP293, -40C TA +125C OP493 OP493, -40C TA +125C -40C TA +125C -40C TA +125C Long Term Offset Voltage VOS POWER SUPPLY Power Supply Rejection Ratio RL = 100 k, 0.03 VOUT 1 V -40C TA +125C Note 1 PSRR Supply Current/Amplifier ISY Supply Voltage Range VS VS = +1.7 V to +6 V, -40C TA +125C VCM = 1.0 V, RL = -40C TA +125C 75 175 100 175 125 225 15 2 1 0 60 "F" Grade Min Typ Max 150 250 250 350 275 375 20 4 1 0 60 70 70 150 100 94 +2 300 97 90 13.2 20 25 18 +2 Units V V V V V V nA nA V V/mV V/mV V 13.2 20 25 18 dB A A V NOISE PERFORMANCE Voltage Noise Density Current Noise Density Voltage Noise en in en p-p f = 1 kHz f = 1 kHz 0.1 Hz to 10 Hz 65 0.05 3 65 0.05 3 nV/Hz pA/Hz V p-p DYNAMIC PERFORMANCE Slew Rate Gain Bandwidth Product SR GBP RL = 2 k 10 25 10 25 V/ms kHz WAFER TEST LIMITS (@ V = +5.0 V, V S CM = 0.1 V, VOUT = 2 V, TA = +258C unless otherwise noted) Parameter Symbol Conditions Limit Units Offset Voltage VOS Input Bias Current Input Offset Current Input Voltage Range1 Common-Mode Rejection Power Supply Rejection Ratio Large Signal Voltage Gain Output Voltage Swing High Output Voltage Swing Low Supply Current/Amplifier IB IOS VCM CMRR PSRR AVO VOH VOL ISY VS = 15 V, VOUT = 0 V VS = +2 V, VOUT = 1.0 V VCM = 1.0 V VCM = 1.0 V 75 75 20 4 0 to 4 96 100 100 4.1 400 25 V max V max nA max nA max V min dB min dB min V/mV min V min mV max A max 0 VCM 4 V VS = 1.5 V to 18 V RL = 100 k IL = 1 mA IL = -1 mA VO = 0 V, RL = , VS = 18 V NOTES Electrical tests and wafer probe to the limits shown. Due to variations in assembly methods and normal yield loss, yield after packaging is not guaranteed for standard product dice. Consult factory to negotiate specifications based on dice lot qualifications through sample lot assembly and testing. 1 Guaranteed by CMRR test. Specifications subject to change without notice. REV. A -5- OP193/OP293/OP493 ABSOLUTE MAXIMUM RATINGS 1 ORDERING GUIDE Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 V Input Voltage2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 V Differential Input Voltage2 . . . . . . . . . . . . . . . . . . . . . . . 18 V Output Short-Circuit Duration to Gnd . . . . . . . . . . Indefinite Storage Temperature Range P, S Package . . . . . . . . . . . . . . . . . . . . . . . -65C to +150C Operating Temperature Range OP193/OP293/OP493E, F . . . . . . . . . . . . -40C to +125C Junction Temperature Range P, S Package . . . . . . . . . . . . . . . . . . . . . . . -65C to +150C Lead Temperature Range (Soldering, 60 sec) . . . . . . . +300C Package Type JA3 JC Units 8-Pin Plastic DIP (P) 8-Pin SOIC (S) 14-Pin Plastic DIP (P) 16-Pin SOL (S) 103 158 83 92 43 43 39 27 C/W C/W C/W C/W NOTES 1 Absolute maximum ratings apply to both DICE and packaged parts, unless otherwise noted. 2 For supply voltages less than 18 V, the input voltage is limited to the supply voltage. 3 JA is specified for the worst case conditions, i.e., JA is specified for device in socket for P-DIP, and JA is specified for device soldered in circuit board for SOIC package. Model Temperature Range Package Description Package Option OP193EP OP193ES OP193ES-REEL OP193ES-REEL7 OP193FP OP193FS OP193FS-REEL OP193FS-REEL7 OP193GBC OP293EP OP293ES OP293ES-REEL OP293ES-REEL7 OP293FP OP293FS OP293FS-REEL OP293FS-REEL7 OP293GBC OP493EP OP493ES OP493ES-REEL OP493FP OP493FS OP493FS-REEL OP493GBC -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C +25C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C +25C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C -40C to +125C +25C 8-Pin Plastic DIP 8-Pin SOIC 8-Pin SOIC 8-Pin SOIC 8-Pin Plastic DIP 8-Pin SOIC 8-Pin SOIC 8-Pin SOIC DICE 8-Pin Plastic DIP 8-Pin SOIC 8-Pin SOIC 8-Pin SOIC 8-Pin Plastic DIP 8-Pin SOIC 8-Pin SOIC 8-Pin SOIC DICE 14-Pin Plastic DIP 16-Pin SOL 16-Pin SOL 14-Pin Plastic DIP 16-Pin SOL 16-Pin SOL DICE N-8 SO-8 SO-8 SO-8 N-8 SO-8 SO-8 SO-8 1 N-8 SO-8 SO-8 SO-8 N-8 SO-8 SO-8 SO-8 N-14 SOL-16 SOL-16 N-14 SOL-16 SOL-16 7 2 DICE CHARACTERISTICS 6 1 8 3 7 4 5 OP193 Die Size 0.070 x 0.055 Inch, 3,850 Sq. Mils Substrate (Die Backside) Is Connected to V- Transistor Count, 55 1 8 7 6 2 6 2 5 3 4 5 OP493 Die Size 0.106 x 0.143 Inch, 15,158 Sq. Mils Substrate (Die Backside) Is Connected to V- Transistor Count, 215 3 4 OP293 Die Size 0.072 x 0.110 Inch, 7,920 Sq. Mils Substrate (Die Backside) Is Connected to V- Transistor Count, 105 CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although the OP193/OP293/OP493 feature proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. -6- WARNING! ESD SENSITIVE DEVICE REV. A Typical Performance Characteristics-OP193/OP293/OP493 450 x PDIPS 120 80 40 Figure 1. OP193 Offset Distribution, VS = 15 V VS = +3V VCM = 0.1V TA = +25C 160 NUMBER OF AMPLIFIERS 160 NUMBER OF AMPLIFIERS 450 x PDIPS 120 80 40 Figure 2. OP193 Offset Distribution, VS = +3 V 150 450 x PDIPS 90 60 30 0 0 0.2 0.6 0.4 TCVOS - V/ C 0.8 -1 +125C -2 1 2 3 4 COMMON MODE VOLTAGE - Volts Figure 7. CMRR vs. Frequency REV. A +PSRR 60 100 1k FREQUENCY - Hz 10k Figure 6. PSRR vs. Frequency 40 SHORT CIRCUIT CURRENT - mA CMRR - dB SLEW RATE - V/ms 10k 80 0 10 5 +SR = -SR VS = 15V 15 +SR = -SR VS = +5V 10 5 100 1k FREQUENCY - Hz 5V VS 30V TA = +25C -PSRR 20 20 0 10 1.0 40 20 VS = +5V 0.8 +25C -3 25 100 0.6 0.4 TCVOS - V/ C -40C TA = +25C 40 0.2 100 0 Figure 5. Input Bias Current vs. Common-Mode Voltage 120 60 30 120 0 Figure 4. OP193 TCVOS Distribution, VS = 15 V 80 60 Figure 3. OP193 TCVOS Distribution, VS = +3 V -4 1.0 VS = 15V 450 x PDIPS 90 VS = +5V INPUT BIAS CURRENT - nA 120 120 0 1 VS = 15V -40C TA +125C VS = +3V VCM = 0.1V -40C TA +125C 0 0 -75 -60 -45 -30 -15 0 15 30 45 60 75 OFFSET - V PSRR - dB NUMBER OF AMPLIFIERS VS = 15V TA = +25C 0 -75 -60 -45 -30 -15 0 15 30 45 60 75 OFFSET - V NUMBER OF AMPLIFIERS 150 200 200 0 -50 -25 +ISC VS = 15V 30 | -ISC | VS = 15V 20 10 | -ISC | VS = +5V 0 25 50 75 100 125 TEMPERATURE - C Figure 8. Slew Rate vs. Temperature -7- 0 -50 -25 +ISC VS = +5V 0 25 50 75 TEMPERATURE - C 100 125 Figure 9. Short Circuit Current vs. Temperature OP193/OP293/OP493-Typical Performance Characteristics -0.5 -0.10 VS = +2V VCM = 0.1V -0.15 -0.20 0 25 -1 20 VS = 18V VS = 15V -2 -3 VS = +2V VCM = 0.1V -4 VS = 15V -0.25 -50 -25 75 0 25 50 TEMPERATURE - C 100 -5 -50 125 25 50 75 100 10 5 0 -50 -25 125 100 10 10 100 FREQUENCY - Hz 100 10 1 10 100 DELTA FROM VCC 100 DELTA FROM VEE 10 0.1 1500 VS = +5V 0.03V VOUT 4V 500 0 -50 -25 0 25 50 75 100 125 TEMPERATURE - C Figure 16. Voltage Gain (RL = 100 k) vs. Temperature VS = 15V -10V VOUT +10V 10000 40 VS = +5V 0.03V VOUT 4V 20 0 200 0 -50 -25 1000 TA = +25C VS = +5V 600 400 100 Figure 15. Delta Output Swing from Either Rail vs. Current Load GAIN - dB VOLTAGE GAIN - V/mV -10V VOUT +10V 10 60 800 VS = 15V 1 LOAD CURRENT - A 1000 2000 125 1000 1k Figure 14. Current Noise Density vs. Frequency 2500 100 5V VS 30V TA = +25C FREQUENCY - Hz Figure 13. Voltage Noise Density vs. Frequency 75 1 0.1 1k 50 10000 5V VS 30V TA = +25C 1 1 25 Figure 12. Supply Current vs. Temperature DELTA FROM SUPPLY RAIL - mV 5V VS 30V TA = +25C 1 0.1 0 TEMPERATURE - C 1000 CURRENT NOISE DENSITY - pA/ Hz VOLTAGE NOISE DENSITY - nV/ Hz 0 VS = +2V VCM = +1V Figure 11. Input Bias Current vs. Temperature 1000 VOLTAGE GAIN - V/mV -25 15 TEMPERATURE - C Figure 10. Input Offset Current vs. Temperature 1000 SUPPLY CURRENT - A INPUT BIAS CURRENT - nA INPUT OFFSET CURRENT - nA 0 -20 0 25 50 75 100 125 TEMPERATURE - C Figure 17. Voltage Gain (RL = 10 k) vs. Temperature -8- 10 100 1k 10k FREQUENCY - Hz 100k Figure 18. Closed-Loop Gain vs. Frequency, VS = 5 V REV. A OP193/OP293/OP493 50 OVERSHOOT - % GAIN - dB 40 20 VS = +5V TA = +25C AV = 1 50mV VIN 150mV LOADS TO GND 30 1k 10k 100k FREQUENCY - Hz 60 45 GAIN 0 0 20 0 10 -OS RL = +OS = | -OS | RL = 10k 100 1000 CAPACITIVE LOAD - pF -45 -20 -90 -40 100 10000 1k 10k 100k 1M FREQUENCY - Hz Figure 21. Open Loop, Gain and Phase vs. Frequency VS = 15V 90 PHASE 45 20 GAIN 0 0 -20 -45 -40 100 -90 1k 10k 100k V+ PHASE - Degrees 40 GAIN - dB 90 20 Figure 20. Small Signal Overshoot vs. Capacitive Load Figure 19. Closed-Loop Gain vs. Frequency, VS = 15 V PHASE 40 +OS RL = 10 100 VS = +5V 40 0 -20 10 60 +OS = | -OS | RL = 50k GAIN - dB TA = +25C VS = 15V I1 I2 +INPUT 2k I3 I4 2k Q5 Q1 Q2 -INPUT OP293, OP493 ONLY 1M Q6 Q4 Q3 Q7 TO OUTPUT STAGE Q8 FREQUENCY - Hz D1 Figure 22. Open Loop, Gain and Phase vs. Frequency R1A R2A R1B R2B I5 FUNCTIONAL DESCRIPTION I6 V- The OP193 family of operational amplifiers are single-supply, micropower, precision amplifiers whose input and output ranges both include ground. Input offset voltage (VOS) is only 75 V maximum, while the output will deliver 5 mA to a load. Supply current is only 17 A. NULLING TERMINALS (OP193 ONLY) Figure 23. OP193/OP293/OP493 Equivalent Input Circuit A simplified schematic of the input stage is shown in Figure 23. Input transistors Q1 and Q2 are PNP devices, which permit the inputs to operate down to ground potential. The input transistors have resistors in series with the base terminals to protect the junctions from over voltage conditions. The second stage is an NPN cascode which is buffered by an emitter follower before driving the final PNP gain stage. V+ Q4 FROM INPUT STAGE The OP193 includes connections to taps on the input load resistors, which can be used to null the input offset voltage, VOS. The OP293 and OP493 have two additional transistors, Q7 and Q8. The behavior of these transistors is discussed in the Output Phase Reversal section of this data sheet. Q1 Q5 OUTPUT Q3 Q2 I3 I2 I1 V- The output stage, shown in Figure 24, is a noninverting NPN "totem-pole" configuration. Current is sourced to the load by emitter follower Q1, while Q2 provides current sink capability. When Q2 saturates, the output is pulled to within 5 mV of ground without an external pull-down resistor. The totem-pole output stage will supply a minimum of 5 mA to an external load, even when operating from a single 3.0 V power supply. Figure 24. OP193/OP293/OP493 Equivalent Output Circuit Q5 tracks the collector current of Q1. When Q1 is on, Q5 keeps Q4 off, and current source I1 keeps Q2 turned off. When Q1 is driven to cutoff (i.e., the output must move toward V-), Q5 allows Q4 to turn on. Q4's collector current then provides the base drive for Q3 and Q2, and the output low voltage swing is set by Q2's VCE,SAT which is about 5 mV. By operating as an emitter follower, Q1 offers a high impedance load to the final PNP collector of the input stage. Base drive to Q2 is derived by monitoring Q1's collector current. Transistor REV. A PHASE - Degrees 60 60 -9- OP193/OP293/OP493 OP193 family amplifiers are unconditionally stable with capacitive loads less than 200 pF. However, the small signal, unitygain overshoot will improve if a resistive load is added. For example, transient overshoot is 20% when driving a 1000 pF/ 10 k load. When driving large capacitive loads in unity-gain configurations, an in-the-loop compensation technique is recommended as illustrated in Figure 28. Input Overvoltage Protection As previously mentioned, the OP193 family of op amps use a PNP input stage with protection resistors in series with the inverting and noninverting inputs. The high breakdown of the PNP transistors, coupled with the protection resistors, provides a large amount of input protection from over voltage conditions. The inputs can therefore be taken 20 V beyond either supply without damaging the amplifier. High performance portable equipment and instruments frequently use lithium cells because of their long shelf life, light weight, and high energy density relative to older primary cells. Most lithium cells have a nominal output voltage of 3 V and are noted for a flat discharge characteristic. The low supply voltage requirement of the OP193, combined with the flat discharge characteristic of the lithium cell, indicates that the OP193 can be operated over the entire useful life of the cell. Figure 25 shows the typical discharge characteristic of a 1 AH lithium cell powering the OP193, OP293, and OP493, with each amplifier, in turn, driving 2.1 Volts into a 100 k load. 4 LITHIUM SULPHUR DIOXIDE CELL VOLTAGE - Volts Driving Capacitive Loads Output Phase Reversal--OP193 The OP193's input PNP collector-base junction can be forwardbiased if the inputs are brought more than one diode drop (0.7 V) below ground. When this happens to the noninverting input, Q4 of the cascode stage turns on and the output goes high. If the positive input signal can go below ground, phase reversal can be prevented by clamping the input to the negative supply (i.e., GND) with a diode. The reverse leakage of the diode will, of course, add to the input bias current of the amplifier. If input bias current is not critical, a 1N914 will add less than 10 nA of leakage. However, its leakage current will double for every 10C increase in ambient temperature. For critical applications, the collector-base junction of a 2N3906 transistor will only add about 10 pA of additional bias current. To limit the current through the diode under fault conditions, a 1 k resistor is recommended in series with the input. (The OP193's internal current limiting resistors will not protect the external diode). 3 2 OP493 OP193 OP293 1 0 0 1000 2000 3000 4000 5000 6000 7000 HOURS Figure 25. Lithium Sulfur Dioxide Cell Discharge Characteristic with OP193 Family and 100 k Loads Input Offset Voltage Nulling Output Phase Reversal--OP293 and OP493 The OP293 and OP493 include lateral PNP transistors Q7 and Q8 to protect against phase reversal. If an input is brought more than one diode drop (0.7 V) below ground, Q7 and Q8 combine to level shift the entire cascode stage, including the bias to Q3 and Q4, simultaneously. In this case Q4 will not saturate and the output remains low. The OP293 and OP493 do not exhibit output phase reversal for inputs up to -5 V below V- at +25C. The phase reversal limit at +125C is about -3 V. If the inputs can be driven below these levels, an external clamp diode, as discussed in the previous section, should be added. The OP193 provides two offset nulling terminals that can be used to adjust the OP193's internal VOS. In general, operational amplifier terminals should never be used to adjust system offset voltages. The offset null circuit of Figure 26 provides about 7 mV of offset adjustment range. A 100 k resistor placed in series with the wiper arm of the offset null potentiometer, as shown in Figure 27, reduces the offset adjustment range to 400 V and is recommended for applications requiring high null resolution. Offset nulling does not adversely affect TCVOS performance, providing that the trimming potentiometer temperature coefficient does not exceed 100 ppm/C. V+ 7 2 OP193 Battery Powered Applications OP193 series op amps can be operated on a minimum supply voltage of +1.7 V, and draw only 13 A of supply current per amplifier from a 2.0 V supply. In many battery-powered circuits, OP193 devices can be continuously operated for thousands of hours before requiring battery replacement, thus reducing equipment downtime and operating cost. 6 4 3 5 1 100k V- Figure 26. Offset Nulling Circuit -10- REV. A OP193/OP293/OP493 V+ R1 240k 7 2 OP193 V+ (+2.5V TO +36V) R2 1.5M C1 1000pF 6 7 2 OP193 4 3 5 6 VOUT (1.23V @ 25C) 5 3 1 4 100k 100k 1 V- Q2 Figure 27. High Resolution Offset Nulling Circuit 3 MAT-01AH Q1 7 6 2 VBE2 5 VBE1 A Micropower False-Ground Generator Some single supply circuits work best when inputs are biased above ground, typically at 1/2 of the supply voltage. In these cases a false ground can be created by using a voltage divider buffered by an amplifier. One such circuit is shown in Figure 28. This circuit will generate a false-ground reference at 1/2 of the supply voltage, while drawing only about 27 A from a 5 V supply. The circuit includes compensation to allow for a 1 F bypass capacitor at the false-ground output. The benefit of a large capacitor is that not only does the false ground present a very low dc resistance to the load, but its ac impedance is low as well. The OP193 can both sink and source more than 5 mA, which improves recovery time from transients in the load current. +5V OR +12V 10k 0.022F 240k 2 7 100 OP193 3 240k +2.5V OR +6V 6 4 1F 1F Figure 28. A Micropower False-Ground Generator V1 R3 68k VBE R4 130k R5 20k OUTPUT ADJUST Figure 29. A Battery Powered Voltage Reference A Single-Supply Current Monitor Current monitoring essentially consists of amplifying the voltage drop across a resistor placed in series with the current to be measured. The difficulty is that only small voltage drops can be tolerated, and with low precision op amps this greatly limits the overall resolution. The single-supply current monitor of Figure 30 has a resolution of 10 A and is capable of monitoring 30 mA of current. This range can be adjusted by changing the current sense resistor R1. When measuring total system current, it may be necessary to include the supply current of the current monitor, which bypasses the current sense resistor, in the final result. This current can be measured and calibrated (together with the residual offset) by adjustment of the offset trim potentiometer, R2. This produces a deliberate temperature dependent offset. However, the supply current of the OP193 is also proportional to temperature, and the two effects tend to track. Current in R4 and R5, which also bypasses R1, can be adjusted via a gain trim. A Battery Powered Voltage Reference The circuit of Figure 29 is a battery-powered voltage reference that draws only 17 A of supply current. At this level, two AA alkaline cells can power this reference for more than 18 months. At an output voltage of 1.23 V @ 25C, drift of the reference is only 5.5 V/C over the industrial temperature range. Load regulation is 85 V/mA with line regulation at 120 V/V. Design of the reference is based on the Brokaw bandgap core technique. Scaling of resistors R1 and R2 produces unequal currents in Q1 and Q2. The resulting VBE across R3 creates a temperature-proportional voltage (PTAT) which, in turn, produces a larger temperature-proportional voltage across R4 and R5, V1. The temperature coefficient of V1 cancels (first order) the complementary to absolute temperature (CTAT) coefficient of VBE1. When adjusted to 1.23 V @ +25C, output voltage tempco is at a minimum. Bandgap references can have start-up problems. With no current in R1 and R2, the OP193 is beyond its positive input range limit and has an undefined output state. Shorting Pin 5 (an offset adjust pin) to ground forces the output high under these circumstances and insures reliable startup without significantly degrading the OP193's offset drift. REV. A -11- V+ TO CIRCUIT UNDER TEST 7 3 OP193 ITEST 6 4 2 5 VOUT = 100mV/mA(ITEST) 1 R2 100k R1 1 R5 100 R2 9.9k R3 100k Figure 30. Single-Supply Current Monitor OP193/OP293/OP493 A Single-Supply Instrumentation Amplifier R1 20k Designing a true single-supply instrumentation amplifier with zero-input and zero-output operation requires special care. The traditional configuration, shown in Figure 31, depends upon amplifier A1's output being at 0 V when the applied commonmode input voltage is at 0 V. Any error at the output is multiplied by the gain of A2. In addition, current flows through resistor R3 as A2's output voltage increases. A1's output must remain at 0 V while sinking the current through R3, or a gain error will result. With a maximum output voltage of 4 V, the current through R3 is only 2 A, but this will still produce an appreciable error. R2 1.98M +5V R3 20k V+ A1 1/2 OP293 -IN V- R4 1.98M +5V 10k Q2 Q1 +5V V+ A2 1/2 OP293 VN2222 +IN R1 20k VOUT V- R2 1.98M Figure 32. An Improved Single-Supply, 0 VIN, 0 VOUT Instrumentation Amplifier +5V R3 20k V+ A1 1/2 OP293 -IN V- R4 1.98M A Low-Power, Temperature to 4-20 mA Transmitter +5V ISINK V+ A2 1/2 OP293 +IN A simple temperature to 4-20 mA transmitter is shown in Figure 33. After calibration, this transmitter is accurate to 0.5C over the -50C to +150C temperature range. The transmitter operates from +8 V to +40 V with supply rejection better than 3 ppm/V. One half of the OP293 is used to buffer the VTEMP pin, while the other half regulates the output current to satisfy the current summation at its noninverting input: VOUT V- Figure 31. A Conventional Instrumentation Amplifier One solution to this problem is to use a pull-down resistor. For example, if R3 = 20 k, then the pull-down resistor must be less than 400 . However, the pull-down resistor appears as a fixed load when a common-mode voltage is applied. With a 4 V common-mode voltage, the additional load current will be 10 mA, which is unacceptable in a low power application. IOUT + V TEMP x ( R6 + R7) R2 x R10 R2 + R6 + R7 - V SET R2 x R10 The change in output current with temperature is the derivative of the transfer function: Figure 32 shows a better solution. A1's sink current is provided by a pair of N-channel FET transistors, configured as a current mirror. With the values shown, sink current of Q2 is about 340 A. Thus, with a common-mode voltage of 4 V, the additional load current is limited to 340 A versus 10 mA with a 400 resistor. V TEMP IOUT = T (R6 + R7) T R2 x R10 1N4002 R4 20k REF-43BZ 2 VIN 2 VOUT 6 VTEMP 3 GND 4 8 1/2 OP293 3 R1 10k 4 1 VTEMP R3 100k R2 1k R5 5k R6 3k 6 VSET ZERO TRIM R7 5k 1/2 OP293 5 V+ +8V TO +40V SPAN TRIM R8 1k 7 2N1711 R9 100k ALL RESISTORS 1/4W, 5% UNLESS OTHERWISE NOTED R10 100 1%, 1/2 W IOUT RLOAD Figure 33. Temperature to 4-20 mA Transmitter -12- REV. A OP193/OP293/OP493 From the formulas, it can be seen that if the span trim is adjusted before the zero trim, the two trims are not interactive, which greatly simplifies the calibration procedure. C1 75nF R1 200k Calibration of the transmitter is simple. First, the slope of the output current versus temperature is calibrated by adjusting the span trim, R7. A couple of iterations may be required to be sure the slope is correct. 8 A1 1/2 OP293 3 R3 100k R4 200k TRIANGLE OUT R7 200k CD4066 VDD 14 +5V S1 CONT 13 2 OUT/IN S2 5 CONT CONT 12 IN/OUT 11 4 IN/OUT S3 6 CONT OUT/IN 10 OUT/IN 9 IN/OUT 8 +5V S4 A Micropower Voltage Controlled Oscillator 7 An OP293 in combination with an inexpensive quad CMOS analog switch forms the precision VCO of Figure 34. This circuit provides triangle and square wave outputs and draws only 50 A from a single 5 V supply. A1 acts as an integrator; S1 switches the charging current symmetrically to yield positive and negative ramps. The integrator is bounded by A2 which acts as a Schmitt trigger with a precise hysteresis of 1.67 volts, set by resistors R5, R6, and R7, and associated CMOS switches. The resulting output of A1 is a triangle wave with upper and lower levels of 3.33 and 1.67 volts. The output of A2 is a square wave with almost rail-to-rail swing. With the components shown, frequency of operation is given by the equation: REV. A SQUARE OUT 5 1 IN/OUT 3 OUT/IN but this can easily be changed by varying C1. The circuit operates well up to 500 Hz. 4 7 +5V Table I. R6 Values vs. Temperature fOUT = VCONTROL (Volts) x 10 Hz/V A2 1/2 OP293 R8 200k Table I shows the values of R6 required for various temperature ranges. 10 k 6.2 k 3 k 6 R6 200k IFS IOUT = (TAMBIENT - TMIN ) + 4 mA TOPERATING 0C to +70C -40C to +85C -55C to +150C 1 R2 200k The zero trim can be set at any known temperature by adjusting R5 until the output current equals: R6 R5 200k +5V 2 VCONTROL Once the span trim has been completed, the zero trim can be made. Remember that adjusting the zero trim will not affect the gain. Temp Range +5V VSS Figure 34. Micropower Voltage Controlled Oscillator A Micropower, Single-Supply Quad Voltage Output 8-Bit DAC The circuit of Figure 35 uses the DAC8408 CMOS quad 8-bit DAC and the OP493 to form a single-supply quad voltage output DAC with a supply drain of only 140 A. The DAC8408 is used in the voltage switching mode and each DAC has an output resistance (10 k) independent of the digital input code. The output amplifiers act as buffers to avoid loading the DACs. The 100 k resistors ensure that the OP493 outputs will swing to within 1/2 LSB of ground, i.e.: 1 1.23V x = 3 mV 2 256 -13- OP193/OP293/OP493 +5V A Single-Supply Micropower Quad Programmable-Gain Amplifier +5V 3.6k 4 +5V AD589 1.23V 1 2 VDD 4 A 1/4 OP493 IOUT1A DAC A VREFA 1/4 DAC8408 2 VOUTA 1 3 11 5 IOUT2A/2B R1 100k 6 DAC B VREFB 1/4 DAC8408 6 IOUT1B B 1/4 OP493 8 VOUTB 7 5 R2 100k 13 25 IOUT1C DAC C V REFC 1/4 DAC8408 C 1/4 OP493 27 24 IOUT2C/2D 23 IOUT1D VOUTC 14 12 The combination of the quad OP493 and the DAC8408 quad 8-bit CMOS DAC creates a quad programmable gain amplifier with a quiescent supply drain of only 140 A (Figure 36). The digital code present at the DAC, which is easily set by a microprocessor, determines the ratio between the fixed DAC feedback resistor and the resistance that the DAC feedback ladder presents to the op amp feedback loop. The gain of each amplifier is: V OUT 256 = V IN n where n equals the decimal equivalent of the 8-bit digital code present at the DAC. If the digital code present at the DAC consists of all zeros, the feedback loop will be open causing the op amp to saturate. The 10 M resistors placed in parallel with the DAC feedback loop eliminates this problem with a very small reduction in gain accuracy. The 2.5 V reference biases the amplifiers to the center of the linear region providing maximum output swing. R3 100k 9 DAC D V REFD 1/4 DAC8408 21 10 D 1/4 OP493 VOUTD 8 R4 100k OP493 DAC DATA BUS PINS 9(LSB)-16(MSB) A/B R/W DAC8408ET DS1 DS2 17 18 19 DIGITAL CONTROL SIGNALS 20 DGND 28 Figure 35. Micropower Single-Supply Quad VoltageOutput 8-Bit DAC -14- REV. A OP193/OP293/OP493 C1 0.1F VINA VDD 3 VIN B 7 +5V 4 VREFA 2 IOUT1A 4 DAC A 1/4 DAC8408 C2 0.1F 1 RFBA R1 10M 2 A 1/4 OP493 IOUT2A/2B 5 VREFB 8 IOUT1B 6 11 R2 10M 6 5 VIN C 26 VI N D 22 B 1/4 OP493 7 C 1/4 OP493 8 D 1/4 OP493 14 VOUTB RFBC VREFC 27 IOUT1C 25 DAC C 1/4 DAC8408 C4 0.1F VOUTA RFBB DAC B 1/4 DAC8408 C3 0.1F 1 3 RFBD DAC D 1/4 DAC8408 R3 10M 9 VOUTC 10 IOUT2C/2D 24 VREFD 21 IOUT1D R4 10M 23 13 12 VOUTD DAC DATA BUS PINS 9(LSB)-16(MSB) OP493 17 DIGITAL CONTROL SIGNALS 18 19 20 A/B R/W +2.5V REFERENCE VOLTAGE DAC8408ET DS1 DS2 DGND 28 Figure 36. Single-Supply Micropower Quad Programmable-Gain Amplifier REV. A -15- OP193/OP293/OP493 OUTLINE DIMENSIONS Dimensions shown in inches and (mm). 8-Lead Epoxy DIP (P Suffix) 8-Lead SO (S Suffix) 8 1 0.2440 (6.20) 0.2284 (5.80) 4 1 0.0196 (0.50) x 45 0.0099 (0.25) 0.0192 (0.49) 0.0138 (0.35) 0.0098 (0.25) 0.0075 (0.19) 8 0 0.100 (2.54) BSC 0.070 (1.77) 0.045 (1.15) 0.015 (0.381) 0.008 (0.204) SEATING PLANE 16-Lead Wide Body SOL (S Suffix) 14-Lead Epoxy DIP (P Suffix) 8 0.280 (7.11) 0.240 (6.10) PIN 1 9 16 0.2992 (7.60) 0.2914 (7.40) 7 0.325 (8.25) 0.300 (7.62) 0.795 (20.19) 0.725 (18.42) 0.060 (1.52) 0.015 (0.38) 0.210 (5.33) MAX 0.130 (3.30) MIN 0.160 (4.06) 0.115 (2.93) 0.100 (2.54) BSC 0.070 (1.77) 0.045 (1.15) PIN 1 8 1 0.195 (4.95) 0.115 (2.93) 0.015 (0.381) 0.008 (0.204) 0.4133 (10.50) 0.3977 (10.00) 0.4193 (10.65) 0.3937 (10.00) 0.1043 (2.65) 0.0926 (2.35) 0.0291 (0.74) x 45 0.0098 (0.25) SEATING PLANE 0.0118 (0.30) 0.0500 (1.27) 0.0040 (0.10) BSC 0.0192 (0.49) 0.0138 (0.35) 0.0125 (0.32) 0.0091 (0.23) 8 0 0.0500 (1.27) 0.0157 (0.40) PRINTED IN U.S.A. 1 0.022 (0.558) 0.014 (0.356) 0.195 (4.95) 0.115 (2.93) 0.130 (3.30) MIN 0.160 (4.06) 0.115 (2.93) 0.0500 (1.27) 0.0160 (0.41) 0.022 (0.558) 0.014 (0.356) 14 0.325 (8.25) 0.300 (7.62) 0.060 (1.52) 0.015 (0.38) 0.210 (5.33) MAX 0.0688 (1.75) 0.0532 (1.35) 0.0500 (1.27) BSC 4 0.430 (10.92) 0.348 (8.84) 0.1968 (5.00) 0.1890 (4.80) 0.0098 (0.25) 0.0040 (0.10) 0.280 (7.11) 0.240 (6.10) PIN 1 0.1574 (4.00) 0.1497 (3.80) PIN 1 5 C1994-18-1/95 5 8 -16- REV. A