Product Folder Sample & Buy Support & Community Tools & Software Technical Documents DS92LV2421, DS92LV2422 SNLS321C - MAY 2010 - REVISED MAY 2016 DS92LV242x 10-MHz to 75-MHz, 24-Bit Channel Link II Serializer And Deserializer 1 Features 3 Description * * * The DS92LV242x chipset translates a parallel 24-bit LVCMOS data interface into a single high-speed CML serial interface with embedded clock information. This single serial stream eliminates skew issues between clock and data, reduces connector size, and reduces interconnect cost for transferring a 24-bit or less bus over FR-4 printed-circuit board backplanes and balanced cables. In addition, the DS92LV242x chipset also features a 3-bit control bus for slow speed signals. This allows for video and display applications with up to 24 bits per pixel (RGB). 1 * * * * * * * * 24-Bit Data, 3-Bit Control, 10- to 75-MHz Clock AC-Coupled STP Interconnect Cable up to 10 m Integrated Terminations on Serializer and Deserializer At-Speed Link BIST Mode and Reporting Pin Optional I2C-Compatible Serial Control Bus Power-Down Mode Minimizes Power Dissipation 1.8-V or 3.3-V Compatible LVCMOS I/O Interface -40 to 85C Temperature Range >8-kV HBM Serializer (DS92LV2421) - Data Scrambler for Reduced EMI - DC-Balance Encoder for AC Coupling - Selectable Output VOD and Adjustable De-emphasis Deserializer (DS92LV2422) - Fast Random Data Lock; No Reference Clock Required - Adjustable Input Receiver Equalization - LOCK (Real-Time Link Status) Reporting Pin - EMI Minimization on Output Parallel Bus (SSCG) - Output Slew Control (OS) Programmable transmit de-emphasis, receive equalization, on-chip scrambling, and DC balancing enables longer distance transmission over lossy cables and backplanes. The DS92LV2422 automatically locks to incoming data without an external reference clock or special sync patterns, providing easy plug-and-go operation. EMI is minimized by the use of low voltage differential signaling, receiver drive strength control, and spread spectrum clocking capability. The DS92LV242x chipset is programmable though an I2C interface as well as through pins. A built-in, atspeed BIST feature validates link integrity and may be used for system diagnostics. The DS92LV2421 is offered in a 48-pin WQFN, and the DS92LV2422 is offered in a 60-pin WQFN package. Both devices operate over the full industrial temperature range of -40C to 85C. 2 Applications * * * * * Device Information(1) Embedded Videos and Displays Medical Imaging and Factory Automation Office Automation (Printers and Scanners) Security and Video Surveillance General-Purpose Data Communication PART NUMBER PACKAGE BODY SIZE (NOM) DS92LV2421 WQFN (48) 7.00 mm x 7.00 mm DS92LV2422 WQFN (60) 9.00 mm x 9.00 mm (1) For all available packages, see the orderable addendum at the end of the data sheet. Typical Application Block Diagram VDDn VDDIO (1.8V or 3.3V) 1.8V DI[7:0] DI[15:8] DI[23:16] CI1 CI2 CI3 CLKIN Graphic Processor OR Video Imager OR ASIC/FPGA PDB Channel Link II 1 Pair / AC Coupled 100 nF 100 nF DOUT+ RIN+ DOUT- RIN100 ohm STP Cable DS92LV2421 Serializer BISTEN Optional VDDn VDDIO 1.8V (1.8V or 3.3V) CMF PDB BISTEN RFB VODSEL DeEmph SCL SDA ID[x] Optional DAP DS92LV2422 Deserializer DO[7:0] DO[15:8] DO[23:16] CO1 CO2 CO3 CLKOUT 24-bit RGB Display OR ASIC/FPGA LOCK PASS STRAP pins not shown SCL SDA ID[x] DAP Copyright (c) 2016, Texas Instruments Incorporated 1 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA. DS92LV2421, DS92LV2422 SNLS321C - MAY 2010 - REVISED MAY 2016 www.ti.com Table of Contents 1 2 3 4 5 6 Features .................................................................. 1 Applications ........................................................... 1 Description ............................................................. 1 Revision History..................................................... 2 Pin Configuration and Functions ......................... 4 Specifications....................................................... 10 6.1 6.2 6.3 6.4 6.5 6.6 6.7 Absolute Maximum Ratings .................................... 10 ESD Ratings............................................................ 10 Recommended Operating Conditions..................... 10 Thermal Information ................................................ 11 Electrical Characteristics - Serializer DC ............... 11 Electrical Characteristics - Deserializer DC ........... 12 Electrical Characteristics - DC and AC Serial Control Bus ........................................................................... 13 6.8 Timing Requirements - DC and AC Serial Control Bus ........................................................................... 13 6.9 Timing Requirements - Serializer for CLKIN.......... 13 6.10 Timing Requirements - Serial Control Bus........... 14 6.11 Switching Characteristics - Serializer................... 14 6.12 Switching Characteristics - Deserializer............... 15 6.13 Typical Characteristics .......................................... 21 7 Detailed Description ............................................ 22 7.2 7.3 7.4 7.5 8 Functional Block Diagrams ..................................... Feature Description................................................. Device Functional Modes........................................ Register Maps ......................................................... 22 23 37 38 Application and Implementation ........................ 41 8.1 Application Information............................................ 41 8.2 Typical Applications ................................................ 42 9 Power Supply Recommendations...................... 46 9.1 Power-Up Requirements and PDB Pin ................... 46 10 Layout................................................................... 47 10.1 Layout Guidelines ................................................. 47 10.2 Layout Example .................................................... 49 11 Device and Documentation Support ................. 51 11.1 11.2 11.3 11.4 11.5 11.6 11.7 Device Support...................................................... Documentation Support ........................................ Related Links ........................................................ Community Resource............................................ Trademarks ........................................................... Electrostatic Discharge Caution ............................ Glossary ................................................................ 51 51 51 51 51 51 52 12 Mechanical, Packaging, and Orderable Information ........................................................... 52 7.1 Overview ................................................................. 22 4 Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision B (April 2013) to Revision C Page * Added ESD Ratings table, Feature Description section, Device Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information section ................................................................................................. 1 * Updated thermal characteristic values based on latest simulation data ............................................................................. 11 * Changed deserializer LVCMOS DC and supply current specification test conditions based on latest production tests .... 12 * Changed IOL test condition for VOL at VDDIO = 3.3 V to 3 mA ............................................................................................... 12 * Changed max value of Deserializer VOL to 0.45 V .............................................................................................................. 12 * Changed test condition parameter for VOL Serial Control Characteristic ............................................................................ 13 * Changed RPU = 10 k condition for the Serial Control Bus Characteristics of tR and tF ................................................... 13 * Added notes for serializer and deserializer switching characteristics verified by characterization ...................................... 14 * Added corresponding pins for deserializer tCLH and tCHL parameter..................................................................................... 15 * Added test condition to tDD deserializer parameter ............................................................................................................. 15 * Changed corrected units for deserializer lock time and delay parameter ........................................................................... 15 * Added serial stream and video control signal filter waveform to Feature Description ........................................................ 23 * Changed "NA" and "Disable" term in Table 5 and Table 6 to "Off" ..................................................................................... 28 * Changed output states to correct values based on OSS_SEL and PDB configuration in Table 7 ..................................... 29 * Added details for Deserializer Map Select strap pin configuration ...................................................................................... 33 * Added clarification on the state of deserializer outputs during BIST mode operation.......................................................... 33 * Added statement to set input to low when entering BIST mode with DS90C241 or DS90UR241 ..................................... 33 * Added note that ID[X] cannot be tied to VSS, as only four device addresses are supported ............................................. 35 * Added RID tolerance and tablenote that RID 0 to set ID[X] ......................................................................................... 35 * Changed statement that CONFIG settings can also by programmed via register .............................................................. 37 2 Submit Documentation Feedback Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 DS92LV2421, DS92LV2422 www.ti.com SNLS321C - MAY 2010 - REVISED MAY 2016 Revision History (continued) * Changed bit description to swap definition for Serializer RFB and VOD ............................................................................. 38 * Changed bit definition for Deserializer OSS_SEL ............................................................................................................... 39 * Changed definition from Reserved to MAP_SEL for Deserializer Reg 0x02[5:4] ............................................................... 39 Changes from Revision A (April 2013) to Revision B * Page Changed layout of National Semiconductor Data Sheet to TI format .................................................................................. 49 Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 Submit Documentation Feedback 3 DS92LV2421, DS92LV2422 SNLS321C - MAY 2010 - REVISED MAY 2016 www.ti.com 5 Pin Configuration and Functions DI9 DI8 DI7 DI6 DI5 BISTEN VDDIO DI4 DI3 DI2 DI1 DI0 36 35 34 33 32 31 30 29 28 27 26 25 RHS Package 48-Pin WQFN Top View DI10 37 24 VODSEL DI11 38 23 De-Emph DI12 39 22 VDDTX DI13 40 21 PDB DI14 41 20 DOUT+ DI15 42 19 DOUT- DI16 43 18 RES2 DI17 44 17 VDDHS DI18 45 16 RES1 DI19 46 15 RES0 DI20 47 14 VDDP DI21 48 13 CONFIG[1] 1 2 3 4 5 6 7 8 9 10 11 12 DI22 DI23 CI2 CI3 CI1 ID[x] VDDL SCL SDA CLKIN RFB CONFIG[0] DAP Not to scale Pin Functions: DS92LV2421 (Serializer) PIN NAME NO. TYPE (1) DESCRIPTION (2) LVCMOS PARALLEL INTERFACE DI[7:0] 34, 33, 32, 29, 28, 27, 26, 25 I Parallel interface data input pins, LVCMOS with pulldown. For 8-bit RED display: DI7 = R7 - MSB, DI0 = R0 - LSB. DI[15:8] 42, 41, 40, 39, 38, 37, 36, 35 I Parallel interface data input pins, LVCMOS with pulldown. For 8-bit GREEN display: DI15 = G7 - MSB, DI8 = G0 - LSB. DI[23:16] 2, 1, 48, 47, 46, 45, 44, 43 I Parallel interface data input pins, LVCMOS with pulldown. For 8-bit BLUE display: DI23 = B7 - MSB, DI16 = B0 - LSB. I Control signal input, LVCMOS with pulldown. For display or video application: CI1 = Data enable input. Control signal pulse width must be 3 clocks or longer to be transmitted when the Control signal filter is enabled (CONFIG[1:0] = 01). There is no restriction on the minimum transition pulse when the control signal filter is disabled (CONFIG[1:0] = 00). The signal is limited to 2 transitions per 130 clocks regardless of the control signal filter setting. I Control signal input, LVCMOS with pulldown. For display or video application: CI2 = Horizontal sync input. Control signal pulse width must be 3 clocks or longer to be transmitted when the control signal filter is enabled (CONFIG[1:0] = 01). There is no restriction on the minimum transition pulse when the control signal filter is disabled (CONFIG[1:0] = 00). The signal is limited to 2 transitions per 130 clocks regardless of the control signal filter setting. CI1 CI2 (1) (2) 4 5 3 G = Ground, I = Input, O = Output, and P = Power 1= HIGH, 0 = LOW Submit Documentation Feedback Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 DS92LV2421, DS92LV2422 www.ti.com SNLS321C - MAY 2010 - REVISED MAY 2016 Pin Functions: DS92LV2421 (Serializer) (continued) PIN NAME NO. TYPE (1) DESCRIPTION (2) CI3 4 I Control signal input, LVCMOS with pulldown. For display or video application: CI3 = Vertical sync input. CI3 is limited to 1 transition per 130 clock cycles. Thus, the minimum pulse width allowed is 130 clock cycles wide. CLKIN 10 I Clock input, LVCMOS with pulldown. Latch or data strobe edge set by RFB pin. I Power-down mode input, LVCMOS with pulldown. PDB = 1, serializer is enabled (normal operation). Refer to Power-Up Requirements and PDB Pin. PDB = 0, serializer is powered down. When the serializer is in the power-down state, the driver outputs (DOUT) are both logic high, the PLL is shutdown, IDD is minimized. Control Registers are RESET. I Differential driver output voltage select (this can also be control by I2C register access), LVCMOS with pulldown. VODSEL = 1, LVDS VOD is 420 mV, 840 mVp-p (typical) -- long cable or de-emphasis apps. VODSEL = 0, LVDS VOD is 280 mV, 560 mVp-p (typical) -- short cable (no de-emphasis), low power mode. I De-emphasis control (this can also be controlled by I2C register access), analog with pullup. De-emphasis = open (float) - disabled. To enable de-emphasis, tie a resistor from this pin to GND or control through register (see Table 3). I Clock input latch or data strobe edge select (this can also be controlled by I2C register access), LVCMOS with pulldown. RFB = 1, parallel interface data and control signals are latched on the rising clock edge. RFB = 0, parallel interface data and control signals are latched on the falling clock edge. 13, 12 I LVCMOS with pulldown. 00: Control Signal Filter DISABLED. 01: Control Signal Filter ENABLED. 10: Reverse compatibility mode to interface with the DS90UR124 or DS99R124Q-Q1. 11: Reverse compatibility mode to interface with the DS90C124. ID[X] 6 I I2C serial control bus device ID address select (optional), analog. Resistor to Ground and 10-k pullup to 1.8-V rail (see Table 11). SCL 8 I I2C serial control bus clock input (optional), LVCMOS. SCL requires an external pullup resistor to VDDIO. SDA 9 I/O BISTEN 31 I BIST mode (optional), LVCMOS with pulldown. BISTEN = 0, BIST is disabled (normal operation). BISTEN = 1, BIST is enabled. RES[2:0] 18, 16, 15 I Reserved (tie low), LVCMOS with pulldown. CONTROL AND CONFIGURATION PDB VODSEL De-Emph RFB CONFIG[1:0] 21 24 23 11 I2C serial control bus data input or output (optional), LVCMOS (open drain). SDA requires an external pullup resistor VDDIO. CHANNEL-LINK II - CML SERIAL INTERFACE DOUT+ 20 O Noninverting output, CML. The output must be AC-coupled with a 0.1-F capacitor. DOUT- 19 O Inverting output, CML. The output must be AC-coupled with a 0.1-F capacitor. Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 Submit Documentation Feedback 5 DS92LV2421, DS92LV2422 SNLS321C - MAY 2010 - REVISED MAY 2016 www.ti.com Pin Functions: DS92LV2421 (Serializer) (continued) PIN NAME TYPE (1) NO. DESCRIPTION (2) POWER AND GROUND (3) VDDL 7 P Logic power, 1.8 V 5% VDDP 14 P PLL power, 1.8 V 5% VDDHS 17 P TX high-speed logic power, 1.8 V 5% VDDTX 22 P Output driver power, 1.8 V 5% VDDIO 30 P LVCMOS I/O power, 1.8 V 5% or 3.3 V 10% DAP G DAP is the large metal contact at the bottom side, located at the center of the WQFN package. Connect to the ground plane (GND) with at least 9 vias. GND (3) The VDD (VDDn and VDDIO) supply ramp must be faster than 1.5 ms with a monotonic rise. If slower then 1.5 ms, then a capacitor on the PDB pin is needed to ensure PDB arrives after all the VDD have settled to the recommended operating voltage. 6 NC BISTEN VDDR PASS/OP_LOW DO0/MAP_SEL0 DO1/MAP_SEL1 DO2 VDDIO DO3/SSC0 DO4/SSC1 DO5/SSC2 DO6/SSC3 DO7 LOCK NC 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 NKB Package 60-Pin WQFN Top View NC 46 30 NC RES 47 29 VDDL VDDIR 48 28 DO8/OSC_SEL0 RIN+ 49 27 DO9/OSC_SEL1 RIN- 50 26 DO10/OSC_SEL2 CMF 51 25 DO11 ROUT+ 52 24 VDDIO ROUT- 53 23 DO12/EQ0 VDDCMLO 54 22 DO13/EQ1 VDDR 55 21 DO14/EQ2 ID[x] 56 20 DO15/EQ3 VDDPR 57 19 DO16 VDDSC 58 18 DO17/RFB PDB 59 17 DO18/OSS_SEL NC 60 16 NC 14 15 DO19/OS_DATA NC 9 DO23/CONFIG[0] 13 8 CO2 12 7 CO3 VDDIO 6 CO1 DO20/LF_MODE 5 CLKOUT 11 4 VDDSC 10 3 SCL DO22/CONFIG[1] 2 SDA Submit Documentation Feedback DO21/OS_CLKOUT 1 NC DAP Not to scale Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 DS92LV2421, DS92LV2422 www.ti.com SNLS321C - MAY 2010 - REVISED MAY 2016 Table 1. Pin Functions: DS92LV2422 (Deserializer) PIN NAME NO. TYPE (1) DESCRIPTION (2) LVCMOS PARALLEL INTERFACE DO[7:0] 33, 34, 35, 36, 37, 39, 40, 41 I/O Parallel interface data output pins, STRAP and LVCMOS. For 8-bit RED display: DO7 = R7 - MSB, DO0 = R0 - LSB. In power down (PDB = 0), outputs are controlled by the OSS_SEL (see Table 7). These pins are inputs during power-up (see Deserializer Strap Input Pins). DO[15:8] 20, 21, 22, 23, 25, 26, 27, 28 I/O Parallel interface data output pins, STRAP and LVCMOS. For 8-bit GREEN display: DO15 = G7 - MSB, DO8 = G0 - LSB. In power down (PDB = 0), outputs are controlled by the OSS_SEL (see Table 7). These pins are inputs during power-up (see Deserializer Strap Input Pins). DO[23:16] 9, 10, 11, 12, 14, 17, 18, 19 I/O Parallel interface data input pins, STRAP and LVCMOS. For 8-bit BLUE display: DO23 = B7 - MSB, DO16 = B0 - LSB. In power down (PDB = 0), outputs are controlled by the OSS_SEL (see Table 7). These pins are inputs during power-up (see Deserializer Strap Input Pins). O Control signal output, LVCMOS. For display or video application: CO1 = Data enable output. Control signal pulse width must be 3 clocks or longer to be transmitted when the control signal filter is enabled (CONFIG[1:0] = 01). There is no restriction on the minimum transition pulse when the control signal filter is disabled (CONFIG[1:0] = 00). The signal is limited to 2 transitions per 130 clocks regardless of the control signal filter setting. In power down (PDB = 0), output is controlled by the OSS_SEL pin (see Table 7). O Control signal output, LVCMOS. For display or video application: CO2 = Horizontal sync output. Control signal pulse width must be 3 clocks or longer to be transmitted when the control signal filter is enabled (CONFIG[1:0] = 01). There is no restriction on the minimum transition pulse when the control signal filter is disabled (CONFIG[1:0] = 00). The signal is limited to 2 transitions per 130 clocks regardless of the control signal filter setting. In power down (PDB = 0), output is controlled by the OSS_SEL pin (see Table 7). CO1 CO2 6 8 CO3 7 O Control signal output, LVCMOS. For display or video application: CO3 = Vertical sync output. CO3 is different than CO1 and CO2 because it is limited to 1 transition per 130 clock cycles. Thus, the minimum pulse width allowed is 130 clock cycles wide. The CONFIG[1:0] pins have no effect on the CO3 signal. In power down (PDB = 0), output is controlled by the OSS_SEL pin (see Table 7). CLKOUT 5 O Pixel clock output, LVCMOS. In power down (PDB = 0), output is controlled by the OSS_SEL pin (see Table 7). Data strobe edge set by RFB. LOCK 32 O LOCK status output, LVCMOS. LOCK = 1, PLL is locked, outputs are active LOCK = 0, PLL is unlocked, DO[23:0], CO1, CO2, CO3 and CLKOUT output states are controlled by OSS_SEL (see Table 7). May be used as link status or to flag when video data is active (ON/OFF). PASS 42 O PASS output (BIST mode), LVCMOS. PASS = 1, error free transmission. PASS = 0, one or more errors were detected in the received payload. Route to test point for monitoring, or leave open if unused. CONTROL AND CONFIGURATION - STRAP PINS (3) CONFIG[1:0] LF_MODE (1) (2) (3) 10 [DO22], 9 [DO23] 12 [DO20] I STRAP or LVCMOS with pulldown. 00: Control Signal Filter DISABLED. 01: Control Signal Filter ENABLED. 10: Reverse compatibility mode to interface with the DS90UR241 or DS99R241-Q1. 11: Reverse compatibility mode to interface with the DS90C241. I SSCG low frequency mode, STRAP or LVCMOS with pulldown. Only required when SSCG is enabled, otherwise LF_MODE condition is a DON'T CARE (X). LF_MODE = 1, SSCG in low frequency mode (CLK = 10 to 20 MHz). LF_MODE = 0, SSCG in high frequency mode (CLK = 20 to 65 MHz). This can also be controlled by I2C register access. G = Ground, I = Input, O = Output, and P = Power 1= HIGH, 0 = LOW For a high state, use a 10-k pullup to VDDIO; for a low state, the IO includes an internal pull down. The strap pins are read upon powerup and set device configuration. Pin number DO[23:0] listed along with shared data output name in square brackets. Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 Submit Documentation Feedback 7 DS92LV2421, DS92LV2422 SNLS321C - MAY 2010 - REVISED MAY 2016 www.ti.com Table 1. Pin Functions: DS92LV2422 (Deserializer) (continued) PIN NAME NO. TYPE (1) DESCRIPTION (2) OS_CLKOUT 11 [DO21] I Output CLKOUT slew select, STRAP or LVCMOS with pulldown. OS_CLKOUT = 1, increased CLKOUT slew rate. OS_CLKOUT = 0, normal CLKOUT slew rate (default). This can also be controlled by I2C register access. OS_DATA 14 [DO19] I Output DO[23:0], CO1, CO2, CO3 slew select; STRAP or LVCMOS with pulldown. OS_DATA = 1, Increased DO slew rate. OS_DATA = 0, Normal DO slew rate (default). This can also be controlled by I2C register access. I Outputs held low when LOCK = 1, STRAP or LVCMOS with pulldown. NOTE: Do not use any other strap options with this strap function enabled. OP_LOW = 1, all outputs are held low during power up until released by programming OP_LOW release/set register HIGH. NOTE: Before the device is powered up, the outputs are in TRI-STATE (see Figure 30 and Figure 31). OP_LOW = 0, all outputs toggle normally as soon as LOCK goes high (default). This can also be controlled by I2C register access. I Output sleep state select, STRAP or LVCMOS with pulldown. OSS_SEL is used in conjunction with PDB to determine the state of the outputs in power down (see Table 7). NOTE: OSS_SEL strap cannot be used if OP_LOW = 1. This can also be controlled by I2C register access. OP_LOW OSS_SEL 42 [PASS] 17 [DO18] RFB 18 [DO17] I Clock output strobe edge select, STRAP or LVCMOS with pulldown. RFB = 1, parallel interface data and control signals are strobed on the rising clock edge. RFB = 0, parallel interface data and control signals are strobed on the falling clock edge. This can also be controlled by I2C register access. EQ[3:0] 20 [DO15], 21 [DO14], 22 [DO13], 23 [DO12] I Receiver input equalization, STRAP or LVCMOS with pulldown (see Table 4). This can also be controlled by I2C register access. OSC_SEL[2:0] 26 [DO10], 27 [DO9], 28 [DO8] I Oscillator select, STRAP or LVCMOS with pulldown (see Table 8 and Table 9). This can also be controlled by I2C register access. SSC[3:0] 34 [DO6], 35 [DO5], 36 [DO4], 37 [DO3] I Spread spectrum clock generation (SSCG) range select, STRAP or LVCMOS with pulldown (see Table 5 and Table 6). This can also be controlled by I2C register access. 40 [D], 41 [D] I Bit mapping reverse compatibility or DS90UR241 options, STRAP or LVCMOS with pulldown. Pin or register control. Default setting is 00'b (see Table 10). MAP_SEL[1:0] CONTROL AND CONFIGURATION PDB 59 I Power-down mode input, LVCMOS with pulldown. PDB = 1, deserializer is enabled (normal operation). Refer to Power-Up Requirements and PDB Pin. PDB = 0, deserializer is in power down. When the deserializer is in the power-down state, the LVCMOS output state is determined by Table 7. Control registers are RESET. ID[X] 56 I I2C serial control bus device ID Address Select (optional), analog. Resistor to ground and 10-k pullup to 1.8-V rail (see Table 11). SCL 3 I I2C serial control bus clock input (optional), LVCMOS. SCL requires an external pullup resistor to VDDIO. SDA 2 I/O BISTEN 44 I BIST enable input (optional), LVCMOS with pulldown. BISTEN = 0, BIST is disabled (normal operation). BISTEN = 1, BIST is enabled. 47 I Reserved (tie low), LVCMOS with pulldown. 1, 15, 16, 30, 31, 45, 46, 60 -- RES NC 8 Submit Documentation Feedback I2C serial control bus data input or output (optional), LVCMOS open drain. SDA requires an external pullup resistor to VDDIO. Not connected, leave pin open (float). Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 DS92LV2421, DS92LV2422 www.ti.com SNLS321C - MAY 2010 - REVISED MAY 2016 Table 1. Pin Functions: DS92LV2422 (Deserializer) (continued) PIN NAME NO. TYPE (1) DESCRIPTION (2) CHANNEL-LINK II -- CML SERIAL INTERFACE RIN+ 49 I True input, CML. The input must be AC-coupled with a 0.1-F capacitor. RIN- 50 I Inverting input, CML. The input must be AC-coupled with a 0.1-F capacitor. CMF 51 I Common-mode filter, analog. VCM center-tap is a virtual ground which may be AC-coupled to ground to increase receiver common mode noise immunity. Recommended value is 4.7 F or higher. ROUT+ 52 O True output (receive signal after the equalizer), CML. NC if not used or connect to test point for monitor. Requires I2C control to enable. ROUT- 53 O Inverting output (receive signal after the equalizer), CML. NC if not used or connect to test point for monitor. Requires I2C control to enable. POWER AND GROUND (4) VDDL 29 P Logic power, 1.8 V 5% VDDIR 48 P Input power, 1.8 V 5% VDDR 43, 55 P RX high-speed logic power, 1.8 V 5% VDDSC 4, 58 P SSCG power, 1.8 V 5% VDDPR 57 P PLL power, 1.8 V 5% VDDCMLO 54 P RX high-speed logic power, 1.8 V 5% 13, 24, 38 P LVCMOS I/O power, 1.8 V 5% or 3.3 V 10% (VDDIO) DAP G DAP is the large metal contact at the bottom side, located at the center of the WQFN package. Connected to the ground plane (GND) with at least 9 vias. VDDIO GND (4) The VDD (VDDn and VDDIO) supply ramp must be faster than 1.5 ms with a monotonic rise. If slower then 1.5 ms, then a capacitor on the PDB pin is needed to ensure PDB arrives after all the VDD have settled to the recommended operating voltage. Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 Submit Documentation Feedback 9 DS92LV2421, DS92LV2422 SNLS321C - MAY 2010 - REVISED MAY 2016 www.ti.com 6 Specifications 6.1 Absolute Maximum Ratings Over operating free-air temperature range (unless otherwise noted) (1) (2) (3) MIN MAX UNIT Supply voltage, VDDn (1.8 V) -0.3 2.5 V Supply voltage, VDDIO -0.3 4 V LVCMOS I/O voltage -0.3 VDDIO + 0.3 V Receiver input voltage -0.3 VDD + 0.3 V -0.3 VDD + 0.3 V 225 mW 1 / RJA mW/C Driver output voltage 48L RHS package 60L NKB package Maximum power dissipation capacity at 25C Derate above 25C Maximum power dissipation capacity at 25C Derate above 25C 525 mW 1 / RJA mW/C 150 C 150 C Junction temperature, TJ Storage temperature, Tstg (1) (2) (3) -65 Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and specifications. For soldering specifications, see product folder at www.ti.com and SNOA549. 6.2 ESD Ratings VALUE Human-body model (HBM), per ANSI/ESDA/JEDEC JS-001 (1) 8000 Charged-device model (CDM), per JEDEC specification JESD22-C101 (2) 1000 Machine model (MM) V(ESD) Electrostatic discharge IEC 61000-4-2 contact discharge IEC 61000-4-2 air-gap discharge (1) (2) UNIT 250 DOUT+, DOUT- 8000 RIN+, RIN- 8000 DOUT+, DOUT- 25000 RIN+, RIN- 25000 V JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process. JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process. 6.3 Recommended Operating Conditions MIN NOM MAX UNIT VDDn Supply voltage 1.71 1.8 1.89 V VDDIO LVCMOS supply voltage 1.71 1.8 1.89 V VDDIO LVCMOS supply voltage 3 3.3 3.6 V Clock frequency 10 Supply noise (1) TA (1) 10 Operating free-air temperature -40 25 75 MHz 50 mVp-p 85 C Supply noise testing was done with minimum capacitors on the PCB. A sinusoidal signal is AC-coupled to the VDDn (1.8 V) supply with amplitude = 100 mVp-p measured at the device VDDn pins. Bit error rate testing of input to the serializer and output of the deserializer with 10 meter cable shows no error when the noise frequency on the serializer is less than 750 kHz. The deserializer, on the other hand, shows no error when the noise frequency is less than 400 kHz. Submit Documentation Feedback Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 DS92LV2421, DS92LV2422 www.ti.com SNLS321C - MAY 2010 - REVISED MAY 2016 6.4 Thermal Information Over operating free-air temperature range (unless otherwise noted) THERMAL METRIC (1) DS92LV2421 DS92LV2422 RHS (WQFN) NKB (WQFN) 48 PINS 60 PINS UNIT RJA Junction-to-ambient thermal resistance (2) 30.3 26.9 C/W RJC(top) Junction-to-case (top) thermal resistance (2) 11.5 9.1 C/W RJB Junction-to-board thermal resistance 7.3 6 C/W JT Junction-to-top characterization parameter 0.1 0.1 C/W JB Junction-to-board characterization parameter 7.3 6 C/W RJC(bot) Junction-to-case (bottom) thermal resistance 2.7 1.5 C/W (1) (2) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application report, SPRA953. Based on nine thermal vias. 6.5 Electrical Characteristics - Serializer DC Over recommended operating supply and temperature ranges (unless otherwise noted). (1) (2) (3) PARAMETER TEST CONDITIONS MIN TYP MAX UNIT LVCMOS INPUT DC SPECIFICATIONS VIH High level input voltage VIL Low level input voltage IIN Input current VDDIO = 3 V to 3.6 V (DI[23:0], CI1,CI2,CI3, CLKIN, PDB, VODSEL, RFB, BISTEN, and CONFIG[1:0] pins) 2.2 VDDIO 0.65 x VDDIO VDDIO VDDIO = 3 V to 3.6 V (DI[23:0], CI1,CI2,CI3, CLKIN, PDB, VODSEL, RFB, BISTEN, and CONFIG[1:0] pins) GND 0.8 VDDIO = 1.71 V to 1.89 V (DI[23:0], CI1,CI2,CI3, CLKIN, PDB, VODSEL, RFB, BISTEN, and CONFIG[1:0] pins) GND 0.35 x VDDIO VDDIO = 1.71 V to 1.89 V (DI[23:0], CI1,CI2,CI3, CLKIN, PDB, VODSEL, RFB, BISTEN, and CONFIG[1:0] pins) V VIN = 0 V or VDDIO (DI[23:0], VDDIO = 3 V to 3.6 V CI1,CI2,CI3, CLKIN, PDB, VODSEL, RFB, BISTEN, and CONFIG[1:0] pins) VDDIO = 1.7 V to 1.89 V V -15 1 15 -15 1 15 A CML DRIVER DC SPECIFICATIONS 205 280 355 Differential output voltage RL = 100 , de-emphasis = disabled (see Figure 2; DOUT+ and DOUT- pins) VODSEL = 0 VOD VODSEL = 1 320 420 520 Differential output voltage (DOUT+) - (DOUT-) RL = 100 , de-emphasis = disabled (see Figure 2; DOUT+ and DOUT- pins) VODSEL = 0 560 VODp-p VODSEL = 1 840 VOD Output voltage unbalance RL = 100 , de-emphasis = disabled, VODSEL = L (DOUT+ and DOUT- pins) VOS Offset voltage (single-ended) At TP A and B (see Figure 1), RL = 100 , de-emphasis = disabled (DOUT+ and DOUT- pins) VOS Offset voltage unbalance (single-ended) At TP A and B (see Figure 1), RL = 100 , de-emphasis = disabled (DOUT+ and DOUT- pins) IOS Output short circuit current DOUT = 0 V, de-emphasis = disabled, VODSEL = 0 (DOUT+ and DOUT- pins) RTO Internal output termination resistor DOUT+ and DOUT- pins (1) (2) (3) 1 VODSEL = 0 1.65 VODSEL = 1 1.575 80 mV mVp-p 50 mV V 1 mV -36 mA 100 120 The electrical characteristics tables list verified specifications under the listed recommended operating conditions except as otherwise modified or specified by the electrical characteristics conditions or notes. Typical specifications are estimations only and are not verified. Typical values represent most likely parametric norms at VDD = 3.3 V, TA = 25C, and at the recommended operation conditions at the time of product characterization and are not verified. Current into device pins is defined as positive. Current out of a device pin is defined as negative. Voltages are referenced to ground except VOD, VOD, VTH, and VTL, which are differential voltages. Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 Submit Documentation Feedback 11 DS92LV2421, DS92LV2422 SNLS321C - MAY 2010 - REVISED MAY 2016 www.ti.com Electrical Characteristics - Serializer DC (continued) Over recommended operating supply and temperature ranges (unless otherwise noted).(1)(2)(3) PARAMETER TEST CONDITIONS MIN TYP MAX 75 90 UNIT SUPPLY CURRENT IDDT1 Serializer supply current (includes load current) IDDIOT1 IDDT2 Serializer supply current (includes load current) IDDIOT2 IDDZ Serializer supply current power-down RL = 100 , CLKIN = 75 MHz, checker board pattern, de-emphasis = 3 k, VODSEL = H (see Figure 9) VDD = 1.89 V RL = 100 , CLKIN = 75 MHz, checker board pattern, de-emphasis = 6 k, VODSEL = L (see Figure 9) PDB = 0 V, All other LVCMOS Inputs =0V IDDIOZ VDDIO = 1.89 V 3 5 VDDIO = 3.6 V 11 15 VDD = 1.89 V 65 80 VDDIO = 1.89 V 3 5 VDDIO = 3.6 V 11 15 VDD = 1.89 V 40 1000 VDDIO = 1.89 V 5 10 VDDIO = 3.6 V 10 20 mA mA A 6.6 Electrical Characteristics - Deserializer DC Over recommended operating supply and temperature ranges (unless otherwise noted). PARAMETER TEST CONDITIONS MIN TYP MAX UNIT V 3.3-V I/O LVCMOS DC SPECIFICATIONS (VDDIO = 3 V TO 3.6 V) VIH High level input voltage PDB and BISTEN pins 2.2 VDDIO VIL Low level input voltage PDB and BISTEN pins GND 0.8 V IIN Input current VIN = 0 V or VDDIO (PDB and BISTEN pins) 15 A VOH High level output voltage IOH = -2 mA, OS_CLKOUT/DATA = L (DO[23:0], CO1, CO2, CO3, CLKOUT, LOCK, and PASS pins) VOL Low level output voltage IOL = 3 mA, OS_CLKOUT/DATA = L (DO[23:0], CO1, CO2, CO3, CLKOUT, LOCK, and PASS pins) GND Output short circuit current VDDIO = 3.3 V, VOUT = 0 V, OS_CLKOUT/DATA = L/H (CLKOUT pin) 36 Output short circuit current VDDIO = 3.3 V, VOUT = 0 V, OS_CLKOUT/DATA = L/H (output pins) 37 TRI-STATE output current PDB = 0 V, OSS_SEL = 0 V, VOUT = H (output pins) IOS IOZ -15 1 2.4 VDDIO V 0.4 V mA -15 15 A 1.8-V I/O LVCMOS DC SPECIFICATIONS (VDDIO = 1.71 V to 1.89 V) VIH High level input voltage PDB and BISTEN pins 1.235 VDDIO V VIL Low level input voltage PDB and BISTEN pins GND 0.595 V IIN Input current VIN = 0 V or VDDIO (PDB and BISTEN pins) -15 1 15 A VOH High level output voltage IOH = -2 mA, OS_CLKOUT/DATA = L/H (DO[23:0], CO1, CO2, CO3, CLKOUT, LOCK, and PASS pins) VDDIO - 0.45 VDDIO VOL Low level output voltage IOL = 2 mA, OS_CLKOUT/DATA = L/H (DO[23:0], CO1, CO2, CO3, CLKOUT, LOCK, and PASS pins) GND Output short circuit current VDDIO = 1.8 V, VOUT = 0 V, OS_CLKOUT/DATA = L/H (CLKOUT pin) 18 Output short circuit current VDDIO = 1.8 V, VOUT = 0 V, OS_CLKOUT/DATA = L/H (output pins) 18 TRI-STATE output current PDB = 0 V, OSS_SEL = 0 V, VOUT = 0 V or VDDIO (output pins) -15 IOS IOZ V 0.45 V mA 15 A CML RECEIVER DC SPECIFICATIONS VTH Differential input threshold high voltage VCM = 1.2 V, RIN+ and RIN- pins (Internal VBIAS) 50 VTL Differential input threshold low voltage VCM = 1.2 V, RIN+ and RIN- pins (Internal VBIAS) -50 VCM Common mode voltage RIN+ and RIN- pins (Internal VBIAS) IIN Input current VIN = 0 V or VDDIO, RIN+ and RIN- pins RTI Internal input termination resistor RIN+ and RIN- pins mV mV 1.2 -15 80 100 V 15 A 120 LOOP THROUGH CML DRIVER OUTPUT DC SPECIFICATIONS (EQ TEST PORT (1)) VOD Differential output voltage ROUT+ and ROUT- pins, RL = 100 542 mV VOS Offset voltage (single-ended) ROUT+ and ROUT- pins, RL = 100 1.4 V (1) 12 Specification is verified by characterization and is not tested in production. Submit Documentation Feedback Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 DS92LV2421, DS92LV2422 www.ti.com SNLS321C - MAY 2010 - REVISED MAY 2016 Electrical Characteristics - Deserializer DC (continued) Over recommended operating supply and temperature ranges (unless otherwise noted). PARAMETER RT Internal termination resistor TEST CONDITIONS MIN TYP MAX UNIT 80 100 120 VDD = 1.89 V 97 115 VDDIO = 1.89 V 40 50 VDDIO = 3.6 V 75 85 VDD = 1.89 V 100 3000 ROUT+ and ROUT- pins SUPPLY CURRENT IDD1 IDDIO1 IDDZ Deserializer supply current (includes load current) Deserializer supply current power down CLKOUT = 75 MHz, checker board pattern, OS_CLKOUT/DATA = H, CL = 4 pF (see Figure 9) PDB = 0 V, All other LVCMOS Inputs = 0 V IDDIOZ VDDIO = 1.89 V 6 50 VDDIO = 3.6 V 12 100 mA A 6.7 Electrical Characteristics - DC and AC Serial Control Bus Over 3.3-V supply and temperature ranges (unless otherwise noted). PARAMETER TEST CONDITIONS MIN VIH Input high level SDA and SCL 2.2 VIL Input low level voltage SDA and SCL GND VHY Input hysteresis VOL Output low level voltage (1) SDA, IOL = 1.25 mA, VDDIO = 3.3 V Iin Input current SDA or SCL, Vin = VDDIO or GND Cin Input capacitance SDA or SCL (1) TYP MAX UNIT VDDIO V 0.8 >50 0 -15 V mV 0.4 V 15 A <5 pF Specification is verified by characterization and is not tested in production. 6.8 Timing Requirements - DC and AC Serial Control Bus Over 3.3-V supply and temperature ranges (unless otherwise noted). PARAMETER TEST CONDITIONS MIN TYP MAX UNIT tR SDA rise time (read) SDA, RPU = 10 k, Cb 400 pF 40 ns tF SDA fall time (read) SDA, RPU = 10 k, Cb 400 pF 25 ns tSU;DAT Set up time (read) 520 ns tHD;DAT Hold up time (read) 55 ns tSP Input filter 50 ns 6.9 Timing Requirements - Serializer for CLKIN Over recommended operating supply and temperature ranges (unless otherwise noted). MIN NOM MAX UNIT tTCP Transmit input CLKIN period PARAMETER 10 MHz to 75 MHz (see Figure 4) 13.3 T 100 ns tTCIH Transmit input CLKIN high time 10 MHz to 75 MHz (see Figure 4) 0.4 x T 0.5 x T 0.6 x T ns tTCIL Transmit input CLKIN low time 10 MHz to 75 MHz (see Figure 4) 0.4 x T 0.5 x T 0.6 x T ns tCLKT CLKIN input transition time 10 MHz to 75 MHz (see Figure 4) 0.5 SSCIN CLKIN input TEST CONDITIONS fmod (spread spectrum at 75 MHz) fdev (spread spectrum at 75 MHz) Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 2.4 ns 35 kHz 2% Submit Documentation Feedback 13 DS92LV2421, DS92LV2422 SNLS321C - MAY 2010 - REVISED MAY 2016 www.ti.com 6.10 Timing Requirements - Serial Control Bus Over recommended operating supply and temperature ranges (unless otherwise noted). PARAMETER TEST CONDITIONS MIN NOM MAX Standard mode 100 Fast mode 400 fSCL SCL clock frequency tLOW SCL low period tHIGH SCL high period tHD;STA Hold time for a start or a repeated start condition (see Figure 18) Standard mode Fast mode 0.6 tSU:STA Set up time for a start or a repeated start condition (see Figure 18) Standard mode 4.7 Fast mode 0.6 tHD;DAT Data hold time (see Figure 18) Standard mode 0 3.45 Fast mode 0 0.9 tSU;DAT Data set up time (see Figure 18) Standard mode 250 Fast mode 100 tSU;STO Set up time for STOP condition (see Figure 18) Standard mode Fast mode 0.6 tBUF Bus free time (between STOP and START; see Figure 18) Standard mode 4.7 Fast mode 1.3 tr SCL and SDA rise time (see Figure 18) Standard mode Fast mode 300 tf SCL and SDA fall time (see Figure 18) Standard mode 300 Fast mode 300 Standard mode 4.7 Fast mode 1.3 Standard mode kHz s 4 Fast mode UNIT s 0.6 4 s s s ns 4 s s 1000 ns ns 6.11 Switching Characteristics - Serializer Over recommended operating supply and temperature ranges (unless otherwise noted). PARAMETER TEST CONDITIONS MIN TYP MAX UNIT tLHT Serializer output low-to-high transition time (see Figure 3) RL = 100 , de-emphasis = disabled, VODSEL = 0 200 RL = 100 , de-emphasis = disabled, VODSEL = 1 200 tHLT Serializer output high-to-low transition time (see Figure 3) RL = 100 , de-emphasis = disabled, VODSEL = 0 200 RL = 100 , de-emphasis = disabled, VODSEL = 1 200 tDIS Input data, setup time (see Figure 4) DI[23:0], CI1, CI2, CI3 to CLKIN 2 ns tDIH Input data, hold time (see Figure 4) CLKIN to DI[23:0], CI1, CI2, CI3 2 ns tXZD Serializer output active to OFF delay (see Figure 6) (1) tPLD Serializer PLL lock time (see Figure 5) (1) (2) (3) tSD Serializer delay, latency (see Figure 7) (1) (1) (2) (3) 14 ps ps 8 15 ns RL = 100 1.4 10 ms RL = 100 144 x T 145 x T ns Specification is verified by characterization and is not tested in production. tPLD and tDDLT is the time required by the serializer and deserializer, respectively, to obtain lock when exiting power-down state with an active clock. When the serializer output is at TRI-STATE the Deserializer loses PLL lock. Resynchronization and Re-lock must occur before data transfer require tPLD Submit Documentation Feedback Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 DS92LV2421, DS92LV2422 www.ti.com SNLS321C - MAY 2010 - REVISED MAY 2016 Switching Characteristics - Serializer (continued) Over recommended operating supply and temperature ranges (unless otherwise noted). PARAMETER Serializer output total jitter (see Figure 8) tDJIT STXBW STX (4) Serializer jitter transfer (function -3 dB bandwidth) Serializer jitter transfer (function peaking) TEST CONDITIONS MIN TYP RL = 100 , de-emphasis = disabled, RANDOM pattern, CLKIN = 75 MHz 0.28 RL = 100 , de-emphasis = disabled, RANDOM pattern, CLKIN = 43 MHz 0.27 RL = 100 , de-emphasis = disabled, RANDOM pattern, CLKIN = 10 MHz 0.35 RL = 100 , de-emphasis = disabled, RANDOM pattern, CLKIN = 75 MHz 3.3 RL = 100 , de-emphasis = disabled, RANDOM pattern, CLKIN = 43 MHz 2.3 RL = 100 , de-emphasis = disabled, RANDOM pattern, CLKIN = 10 MHz 0.8 RL = 100 , de-emphasis = disabled, RANDOM pattern, CLKIN = 75 MHz 0.86 RL = 100 , de-emphasis = disabled, RANDOM pattern, CLKIN = 43 MHz 0.83 RL = 100 , de-emphasis = disabled, RANDOM pattern, CLKIN = 10 MHz 0.28 MAX UNIT UI (4) MHz dB UI - Unit Interval is equivalent to one serialized data bit width (1 UI = 1 / [28 x CLK]). The UI scales with clock frequency. 6.12 Switching Characteristics - Deserializer Over recommended operating supply and temperature ranges (unless otherwise noted). PARAMETER tRCP CLK output period tRDC CLK output duty cycle TEST CONDITIONS MIN TYP MAX UNIT 13.3 T 100 ns SSCG = OFF, 10 to 75 MHz 40% 50% 60% SSCG = ON, 10 to 20 MHz 35% 59% 65% SSCG = ON, 10 to 65 MHz 40% 53% 60% tRCP = tTCP (CLKOUT) CLKOUT VDDIO = 1.8 V, CL = 4 pF, OS_CLKOUT/DATA = L 2.1 VDDIO = 3.3 V, CL = 4 pF, OS_CLKOUT/DATA = H 2 VDDIO = 1.8 V, CL = 4 pF, OS_CLKOUT/DATA = L 1.6 VDDIO = 3.3 V, CL = 4 pF, OS_CLKOUT/DATA = H 1.5 LVCMOS low-to-high transition time (see Figure 10) DO[23:0], CO1, CO2, CO3 LVCMOS high-to-low transition time (see Figure 10) DO[23:0], CO1, CO2, CO3 tROS Data valid before CLKOUT, setup time (see Figure 14) VDDIO = 1.71 to 1.89 V or 3 to 3.6 V, CL = 4 pF (lumped load), DO[23:0], CO1, CO2, CO3 0.23 x T 0.5 x T ns tROH Data valid after CLKOUT, hold time (see Figure 14) VDDIO = 1.71 to 1.89 V or 3 to 3.6 V, CL = 4 pF (lumped load), DO[23:0], CO1, CO2, CO3 0.33 x T 0.5 x T ns tCLH tCHL CLKOUT = 10 MHz, SSC[3:0] = OFF (1) tDDLT tDD (1) (2) Deserializer lock time (see Figure 13) Deserializer delay, latency (see Figure 11) CLKOUT = 75 MHz, SSC[3:0] = OFF (1) ns ns 3 4 CLKOUT = 10 MHz, SSC[3:0] = ON (1) 30 CLKOUT = 65 MHz, SSC[3:0] = ON (1) 6 CLKOUT = 10 to 75 MHz, SSC[3:0] = OFF (2) 139 x T ms 140 x T ns tPLD and tDDLT is the time required by the serializer and deserializer, respectively, to obtain lock when exiting power-down state with an active clock. Specification is verified by design and is not tested in production. Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 Submit Documentation Feedback 15 DS92LV2421, DS92LV2422 SNLS321C - MAY 2010 - REVISED MAY 2016 www.ti.com Switching Characteristics - Deserializer (continued) Over recommended operating supply and temperature ranges (unless otherwise noted). PARAMETER tDPJ Deserializer period jitter tDCCJ Deserializer cycle-to-cycle jitter TEST CONDITIONS TYP MAX CLKOUT = 10 MHz 500 1000 SSC[3:0] = OFF (3) (2) CLKOUT = 65 MHz 550 1250 CLKOUT = 75 MHz 435 900 CLKOUT = 10 MHz 375 900 CLKOUT = 65 MHz 500 1150 CLKOUT = 75 MHz 460 1000 jitter freq < 2 MHz 0.9 jitter freq > 6 MHz 0.5 SSC[3:0] = OFF (4) (2) (5) EQ = OFF, Deserializer input jitter tolerance SSCG = OFF, (see Figure 16) CLKOUT = 75 MHz tIJT MIN UNIT ps ps UI (6) BIST MODE tPASS BIST PASS valid time (see Figure 17) BISTEN = 1 1 10 s SSCG MODE fDEV Spread spectrum clocking deviation frequency CLKOUT = 10 to 65 MHz, SSC[3:0] = ON 0.5% 2% fMOD Spread spectrum clocking modulation frequency CLKOUT = 10 to 65 MHz, SSC[3:0] = ON 8 100 (3) (4) (5) (6) kHz tDPJ is the maximum amount the period is allowed to deviate over many samples. Specification is verified by characterization and is not tested in production. tDCCJ is the maximum amount of jitter between adjacent clock cycles. UI - Unit Interval is equivalent to one serialized data bit width (1 UI = 1 / [28 x CLK]). The UI scales with clock frequency. A A' CA Scope 50: 50: B CB B' 50: 50: Single-Ended Figure 1. Serializer Test Circuit DOUT+ VOD- VOD+ DOUT- VOS VOD+ (DOUT+) - (DOUT+) VODp-p 0V VOD- Differential GND Figure 2. Serializer Output Waveforms 16 Submit Documentation Feedback Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 DS92LV2421, DS92LV2422 www.ti.com SNLS321C - MAY 2010 - REVISED MAY 2016 +VOD 80% (DOUT+) - (DOUT-) 0V 20% -VOD tLLHT tLHLT Figure 3. Serializer Output Transition Times tTCIH tTCP CLKIN w/ RFB = L tTCIL 80% 20% 1/2 VDDIO tCLKT tDIS GND tCLKT VDDIO VIHmin VILmax DI[23:0], CI1,CI2,CI3 VDDIO GND tDIH Figure 4. Serializer Input CLKIN Waveform and Set and Hold Times PDB CLKIN 1/2 VDDIO "X" active tPLD DOUT (Diff.) Driver OFF, VOD = 0V Driver On Figure 5. Serializer Lock Time 1/2 VDDIO PDB CLKIN active "X" tXZD DOUT (Diff.) active Driver OFF, VOD = 0V Figure 6. Serializer Disable Time Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 Submit Documentation Feedback 17 DS92LV2421, DS92LV2422 SNLS321C - MAY 2010 - REVISED MAY 2016 DIN[23:0], CI1,CI2,CI3 SYMBOL N www.ti.com SYMBOL N+1 tSD CLKIN (RFB = L) START BIT STOP START BIT BIT STOP BIT DOUT (Diff.) SYMBOL N-1 SYMBOL N Figure 7. Serializer Latency Delay tDJIT tDJIT VOD (+) DOUT (Diff.) TxOUT_E_O 0V VOD (-) tBIT (1 UI) Figure 8. Serializer Output Jitter VDDIO CLKIN/ CLKOUT w/ RFB = L GND VDDIO DI/DO (odd), CI2/CO2, CI3/CO3 GND VDDIO DI/DO (even), CI1/CO1 GND Figure 9. Checkerboard Data Pattern VDDIO 80% 20% GND tCLH tCHL Figure 10. Deserializer LVCMOS Transition Times 18 Submit Documentation Feedback Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 DS92LV2421, DS92LV2422 www.ti.com SNLS321C - MAY 2010 - REVISED MAY 2016 START BIT STOP START BIT BIT STOP BIT RIN (Diff.) SYMBOL N SYMBOL N+1 tDD CLKOUT (RFB = L) DO[23:0], CO1,CO2,CO3 SYMBOL N-2 SYMBOL N-1 SYMBOL N Figure 11. Deserializer Delay - Latency 1/2 VDDIO PDB RIN (Diff.) active "X" tXZR CLKOUT, DO[23:0], CO1,CO2,CO3 PASS, LOCK active Z (TRI-STATE) Figure 12. Deserializer Disable Time (OSS_SEL = 0) PDB 2.0V 0.8V RIN (Diff.) 'RQW &DUH tDDLT LOCK TRI-STATE or LOW Z or L tRxZ DO[23:0], CO1,CO2,CO3 TRI-STATE or LOW or Pulled Up CLKOUT (RFB = L) Z or L or PU TRI-STATE or LOW OFF IN LOCK TIME Z or L ACTIVE OFF Figure 13. Deserializer PLL Lock Times and PDB Tri-State Delay Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 Submit Documentation Feedback 19 DS92LV2421, DS92LV2422 SNLS321C - MAY 2010 - REVISED MAY 2016 www.ti.com VDDIO CLKOUT w/ RFB = H 1/2 VDDIO GND VDDIO DO[23:0], CO1,CO2,CO3 1/2 VDDIO 1/2 VDDIO GND tROS tROH Figure 14. Deserializer Output Data Valid (Setup and Hold) Times With SSCG = Off VDDIO CLKOUT w/ RFB = H 1/2 VDDIO GND DO[23:0], CO1,CO2,CO3 1/2 VDDIO 1/2 VDDIO tROS tROH VDDIO GND Figure 15. Deserializer Output Data Valid (Setup And Hold) Times With SSCG = On Ideal Data Bit End Sampling Window Ideal Data Bit Beginning RxIN_TOL Left VTH 0V VTL RxIN_TOL Right Ideal Center Position (tBIT/2) tBIT (1 UI) tRJIT = RxIN_TOL (Left + Right) - tRJIT Sampling Window = 1 UI Figure 16. Receiver Input Jitter Tolerance BISTEN 1/2 VDDIO tPASS PASS (w/ errors) 1/2 VDDIO Prior BIST Result Current BIST Test - Toggle on Error Result Held Figure 17. BIST Pass Waveform 20 Submit Documentation Feedback Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 DS92LV2421, DS92LV2422 www.ti.com SNLS321C - MAY 2010 - REVISED MAY 2016 SDA tLOW tf tHD;STA tr tf tr tBUF tSP SCL tSU;STA tHD;STA tHIGH tHD;DAT START tSU;STO tSU;DAT STOP REPEATED START START Figure 18. Serial Control Bus Timing Diagram 6.13 Typical Characteristics Figure 19. Differential Output Voltage vs Ambient Temperature Figure 20. ROUT (CMLOUT) VOD vs Ambient Temperature Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 Submit Documentation Feedback 21 DS92LV2421, DS92LV2422 SNLS321C - MAY 2010 - REVISED MAY 2016 www.ti.com 7 Detailed Description 7.1 Overview The DS92LV242x chipset transmits and receives 24 bits of data and 3 control signals over a single serial CML pair operating at 280 Mbps to 2.1 Gbps. The serial stream also contains an embedded clock, video control signals, and the DC-balance information which enhances signal quality and supports AC coupling. The deserializer can attain lock to a data stream without the use of a separate reference clock source, which greatly simplifies system complexity and overall cost. The deserializer also synchronizes to the serializer regardless of the data pattern, delivering true automatic plug and lock performance. It can lock to the incoming serial stream without the need of special training patterns or sync characters. The deserializer recovers the clock and data by extracting the embedded clock information, validating, and then deserializing the incoming data stream, providing a parallel LVCMOS video bus to the display, ASIC, or FPGA. The DS92LV242x chipset can operate in 24-bit color depth (with DE, HS, VS encoded within the serial data stream). In 18-bit color applications, the three video control signals may be sent encoded within the serial bit stream (restrictions apply, see Video Control Signal Filter - Serializer and Deserializer) along with six additional general-purpose signals. 7.2 Functional Block Diagrams RFB CLKIN PLL Parallel to Serial Input Latch DI[23:0] CI1/DE CI2/HS CI3/VS DC Balance Encoder VODSEL De-Emph DOUT+ DOUT- Pattern Generator PDB SCL SCA ID[x] Timing and Control BISTEN Copyright (c) 2016, Texas Instruments Incorporated Figure 21. DS92LV2421 - Serializer 22 Submit Documentation Feedback Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 DS92LV2421, DS92LV2422 www.ti.com SNLS321C - MAY 2010 - REVISED MAY 2016 Functional Block Diagrams (continued) STRAP INPUT SSCG CMF RIN+ EQ DO[23:0] Output Latch Serial to Parallel ROUT- DC Balance Decoder ROUT+ CO1/DE CO2/HS CO3/VS LF_MODE OS_CLKOUT OS_DATA OSS_SEL RFB EQ [3:0] OSC_SEL [2:0] SSC [3:0] RINSTRAP INPUT Error Detector BISTEN PDB SCL SCA ID[x] PASS Clock and Data Recovery Timing and Control OP_LOW CLKOUT LOCK Copyright (c) 2016, Texas Instruments Incorporated Figure 22. DS92LV2422 - Deserializer 7.3 Feature Description 7.3.1 Data Transfer The DS92LV242x chipset transmits and receives a pixel of data in the following format: C1 and C0 represent the embedded clock in the serial stream. C1 is always high and C0 is always low. The b[23:0] contains the scrambled LVCMOS data. DCB is the DC-Balanced control bit. DCB is used to minimize the short and long-term DC bias on the signal lines. This bit determines if the data is unmodified or inverted. DCA is used to validate data integrity in the embedded data stream and can also contain encoded control (VS, HS, DE). Both DCA and DCB coding schemes are generated by the serializer and decoded by the deserializer automatically. Figure 23 illustrates the serial stream per clock cycle. NOTE Figure 23 only illustrates the bits but does not actually represent the bit location as the bits are scrambled and balanced continuously. C 1 b 0 b 1 D C B b 2 b 1 2 b 3 b 1 3 b 4 b 1 4 b 5 b 1 5 b 6 b 1 6 b 7 b 1 7 b 8 b 1 8 b 9 b 1 9 b 1 0 b 2 0 b 1 1 b 2 1 D C A b 2 2 b 2 3 C 0 Figure 23. Channel Link II Serial Stream (DS92LV242x) Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 Submit Documentation Feedback 23 DS92LV2421, DS92LV2422 SNLS321C - MAY 2010 - REVISED MAY 2016 www.ti.com Feature Description (continued) 7.3.2 Video Control Signal Filter - Serializer and Deserializer When operating the devices in normal mode, the video control signals (DE, HS, VS) have the following restrictions: * Normal mode with control signal filter enabled: - DE and HS: Only 2 transitions per 130 clock cycles are transmitted, the transition pulse must be 3 CLK cycles or longer. * Normal mode with control signal filter disabled: - DE and HS: Only 2 transitions per 130 clock cycles are transmitted, no restriction on minimum transition pulse. * VS: Only 1 transition per 130 clock cycles are transmitted, minimum pulse width is 130 clock cycles. Video control signals are defined as low frequency signals with limited transitions. Glitches of a control signal can cause a visual display error. This feature allows for the chipset to validate and filter out any high frequency noise on the control signals (see Figure 24). CLKIN HS/VS/DE IN Latency CLKOUT HS/VS/DE OUT Pulses 1 or 2 CLK cycles wide Filtered OUT Figure 24. Video Control Signal Filter Waveform 7.3.3 Serializer Functional Description The serializer converts a wide parallel input bus to a single serial output data stream and also acts as a signal generator for the chipset Built In Self Test (BIST) mode. The device can be configured through external pins or through the optional serial control bus. The serializer features enhance signal quality on the link by supporting: a selectable VOD level, a selectable de-emphasis signal conditioning, and Channel Link II data coding that provides randomization, scrambling, and DC balancing of the data. The serializer includes multiple features to reduce EMI associated with display data transmission. This includes the randomization and scrambling of the data and system spread spectrum clock support. The serializer features power-saving features with a sleep mode, auto stop clock feature, and optional LVCMOS (1.8 V) parallel bus compatibility (see also Optional Serial Bus Control and Built-In Self Test (BIST)). 7.3.3.1 EMI Reduction Features 7.3.3.1.1 Data Randomization and Scrambling Channel Link II serializers and deserializers feature a three-step encoding process that enables the use of ACcoupled interconnects and also helps to manage EMI. The serializer first passes the parallel data through a scrambler which randomizes the data. The randomized data is then DC-balanced. The DC-balanced and randomized data then goes through a bit-shuffling circuit and is transmitted out on the serial line. This encoding process helps to prevent static data patterns on the serial stream. The resulting frequency content of the serial stream ranges from the parallel clock frequency to the serial Nyquist rate. For example, if the serializer and deserializer chip set is operating at a parallel clock frequency of 75 MHz, the resulting frequency content of serial stream ranges from 75 MHz to 1.05 GHz (75 MHz x 28 bits / 2 = 2.1 GHz / 2 = 1.05 GHz). 24 Submit Documentation Feedback Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 DS92LV2421, DS92LV2422 www.ti.com SNLS321C - MAY 2010 - REVISED MAY 2016 Feature Description (continued) 7.3.3.1.2 Serializer Spread Spectrum Compatibility The serializer CLKIN is capable of tracking spread spectrum clocking (SSC) from a host source. The CLKIN accepts spread spectrum tracking up to 35-kHz modulation and 0.5, 1, or 2% deviations (center spread). The maximum conditions for the CLKIN input are: a modulation frequency of 35 kHz and amplitude deviations of 2% (4% total). 7.3.3.2 Signal Quality Enhancers 7.3.3.2.1 Serializer VOD Select (VODSEL) The serializer differential output voltage may be increased by setting the VODSEL pin high. When VODSEL is low, the DC VOD is at the standard (default) level. When VODSEL is high, the VOD is increased in level. The increased VOD is useful in extremely high noise environments and also on extra long cable length applications. When using de-emphasis, TI recommends setting VODSEL = H to avoid excessive signal attenuation, especially with the larger de-emphasis settings. This feature may be controlled by the external pin or by register. Table 2. Differential Output Voltage INPUT 7.3.3.2.2 EFFECT VODSEL VOD (mV) VOD (mVp-p) H 420 840 L 280 560 Serializer De-Emphasis (De-Emph) The de-emphasis pin controls the amount of de-emphasis beginning one full bit time after a logic transition that the serializer drives. This is useful to counteract loading effects of long or lossy cables. This pin must be left open for standard switching currents (no de-emphasis) or if controlled by register. De-emphasis is selected by connecting a resistor on this pin to ground, with R value between 0.5 k to 1 M, or by register setting. When using de-emphasis, TI recommends to set VODSEL = H. Table 3. De-Emphasis Resistor Value RESISTOR VALUE (k) DE-EMPHASIS SETTING Open Disabled 0.6 -12 dB 1 -9 dB 2 -6 dB 5 -3 dB 0.00 VDD = 1.8V, -2.00 TA = 25oC DE-EMPH (dB) -4.00 -6.00 -8.00 -10.00 -12.00 -14.00 1.0E+02 1.0E+03 1.0E+04 1.0E+05 1.0E+06 R VALUE - LOG SCALE (:) Figure 25. De-Emphasis vs R Value Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 Submit Documentation Feedback 25 DS92LV2421, DS92LV2422 SNLS321C - MAY 2010 - REVISED MAY 2016 www.ti.com 7.3.3.3 Power-Saving Features 7.3.3.3.1 Serializer Power-Down Feature (PDB) The serializer has a PDB input pin to enable or power down the device. This pin is controlled by the host and is used to save power, disabling the link when it is not needed. In power-down mode, the high-speed driver outputs are both pulled to VDD and present a 0-V VOD state. NOTE In power down, the optional serial bus control registers are RESET. 7.3.3.3.2 Serializer Stop Clock Feature The serializer enters a low power SLEEP state when the CLKIN is stopped. A STOP condition is detected when the input clock frequency is less than 3 MHz. The clock must be held at a static low or high state. When the CLKIN starts again, the serializer locks to the valid input clock and then transmits the serial data to the deserializer. NOTE In STOP CLOCK SLEEP, the optional serial bus control register values are RETAINED. 7.3.3.3.3 1.8-V or 3.3-V VDDIO Operation The serializer parallel bus and serial bus interface can operate with 1.8-V or 3.3-V levels (VDDIO) for host compatibility. The 1.8-V levels offer lower noise (EMI) and also system power savings. 7.3.3.3.4 Deserializer Power-Down Feature (PDB) The deserializer has a PDB input pin to enable or power down the device. This pin can be controlled by the system to save power, disabling the deserializer when the display is not needed. An auto-detect mode is also available. In this mode, the PDB pin is tied high and the deserializer enters power down when the serial stream stops. When the serial stream starts up again, the deserializer locks to the input stream and assert the LOCK pin and output valid data. In power-down mode, the data and CLKOUT output states are determined by the OSS_SEL status. NOTE In power down, the optional serial bus control registers are RESET. 7.3.3.3.5 Deserializer Stop Stream SLEEP Feature The deserializer enters a low power SLEEP state when the input serial stream is stopped. A STOP condition is detected when the embedded clock bits are not present. When the serial stream starts again, the deserializer then locks to the incoming signal and recover the data. NOTE In STOP STREAM SLEEP, the optional serial bus control registers values are RETAINED. 7.3.3.4 Serializer Pixel Clock Edge Select (RFB) The RFB pin determines the edge that the data is latched on. If RFB is high, input data is latched on the rising edge of the CLKIN. If RFB is low, input data is latched on the falling edge of the CLKIN. Serializer and deserializer may be set differently. This feature may be controlled by the external pin or by register. 7.3.3.5 Optional Serial Bus Control See Optional Serial Bus Control. 26 Submit Documentation Feedback Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 DS92LV2421, DS92LV2422 www.ti.com SNLS321C - MAY 2010 - REVISED MAY 2016 7.3.3.6 Optional BIST Mode See Built-In Self Test (BIST). 7.3.4 Deserializer Functional Description The deserializer converts a single input serial data stream to a wide parallel output bus and also provides a signal check for the chipset Built-In Self Test (BIST) mode. The device can be configured through external pins and strap pins or through the optional serial control bus. The deserializer features enhance signal quality on the link by supporting an equalizer input and Channel Link II data coding that provides randomization, scrambling, and DC balancing of the data. The deserializer includes multiple features to reduce EMI associated with display data transmission. This includes the randomization and scrambling of the data and output spread spectrum clock generation (SSCG) support. The deserializer features power-saving features with a power-down mode and optional LVCMOS (1.8 V) interface compatibility. 7.3.4.1 Signal Quality Enhancers 7.3.4.1.1 Deserializer Input Equalizer Gain (EQ) The deserializer can enable receiver input equalization of the serial stream to increase the eye opening to the deserializer input. NOTE This function cannot be seen at the RxIN input but can be observed at the serial test port (ROUT) enabled through the serial bus control registers. The equalization feature may be controlled by the external pin or by register. Table 4. Receiver Equalization Configuration Table INPUTS (1) EQ3 EQ2 L L EFFECT EQ1 EQ0 L L H L H H 3 dB L H L H 4.5 dB L H H H 6 dB H L L H 7.5 dB H L H H 9 dB H H L H 10.5 dB H H H H 12 dB X X X L OFF (1) 1.5 dB Default Setting is EQ = Off 7.3.4.2 EMI Reduction Features 7.3.4.2.1 Deserializer Output Slew Rate Select (OS_CLKOUT/OS_DATA) The parallel bus outputs (DO[23:0], CO[3:1], and CLKOUT) of the deserializer feature a selectable output slew. The DATA (DO[23:0], CO[3:1]) are controlled by strap pin or register bit OS_DATA. The CLKOUT is controlled by strap pin or register bit OS_CLKOUT. When the OS_CLKOUT/DATA = H, the maximum slew rate is selected. When the OS_PCLK/DATA = L, the minimum slew rate is selected. Use the higher slew rate setting when driving longer traces or a heavier capacitive load. 7.3.4.2.2 Deserializer Common-Mode Filter Pin (CMF) (Optional) The deserializer provides access to the center tap of the internal termination. A capacitor may be placed on this pin for additional common-mode filtering of the differential pair. This can be useful in high-noise environments for additional noise rejection capability. A 4.7-F capacitor may be connected from this pin to Ground. Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 Submit Documentation Feedback 27 DS92LV2421, DS92LV2422 SNLS321C - MAY 2010 - REVISED MAY 2016 www.ti.com 7.3.4.2.3 Deserializer SSCG Generation (Optional) The deserializer provides an internally generated spread spectrum clock (SSCG) to modulate its outputs. Both clock and data outputs are modulated. This aids to lower system EMI. Output SSCG deviations of 2% (4% total) at up to 100-kHz modulations are available (see Table 5). This feature may be controlled by external strap pins or by register. NOTE The device supports SSCG function with CLKOUT = 10 MHz to 65 MHz. When the CLKOUT = 65 MHz to 75 MHz, it is required to disable the SSCG function (SSC[3:0] = 0000). Frequency FCLKOUT+ fdev(max) FCLKOUT FCLKOUT- fdev(min) Time 1/fmod Figure 26. SSCG Waveform Table 5. SSCG Configuration (LF_MODE = L) - Deserializer Output SSC[3:0] INPUTS LF_MODE = L (20 - 65 MHz) 28 RESULT SSC3 SSC2 SSC1 SSC0 fdev (%) fmod (kHz) L L L L Off Off L L L H 0.5 L L H L 1 L L H H 1.5 L H L L 2 L H L H 0.5 L H H L 1 L H H H 1.5 H L L L 2 H L L H 0.5 H L H L 1 H L H H 1.5 H H L L 2 H H L H 0.5 H H H L 1 H H H H 1.5 Submit Documentation Feedback CLK/2168 CLK/1300 CLK/868 CLK/650 Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 DS92LV2421, DS92LV2422 www.ti.com SNLS321C - MAY 2010 - REVISED MAY 2016 Table 6. SSCG Configuration (LF_MODE = H) - Deserializer Output SSC[3:0] INPUTS LF_MODE = H (10 - 20 MHz) RESULT SSC3 SSC2 SSC1 SSC0 fdev (%) fmod (kHz) L L L L L L L Off Off H 0.5 L L H L 1 L L H H 1.5 L H L L 2 L H L H 0.5 L H H L 1 L H H H 1.5 H L L L 2 H L L H 0.5 H L H L 1 H L H H 1.5 H H L L 2 H H L H 0.5 H H H L 1 H H H H 1.5 CLK/620 CLK/370 CLK/258 CLK/192 7.3.4.2.4 1.8-V or 3.3-V VDDIO Operation The deserializer parallel bus and serial bus interface can operate with 1.8-V or 3.3-V levels (VDDIO) for target (display) compatibility. The 1.8-V levels offer a lower noise (EMI) and also system power savings. 7.3.4.3 Deserializer Clock-Data Recovery Status Flag (LOCK) And Output State Select (OSS_SEL) When PDB is driven high, the CDR PLL begins locking to the serial input and LOCK goes from TRI-STATE to low (depending on the value of the OSS_SEL setting). After the DS92LV2422 completes its lock sequence to the input serial data, the LOCK output is driven high, indicating valid data and clock recovered from the serial input is available on the parallel bus and clock outputs. The CLKOUT output is held at its current state at the change from OSC_CLK (if this is enabled through OSC_SEL) to the recovered clock (or vice versa). If there is a loss of clock from the input serial stream, LOCK is driven low and the state of the outputs are based on the OSS_SEL setting (strap pin configuration or register). 7.3.4.4 Deserializer Oscillator Output (Optional) The deserializer provides an optional clock output when the input clock (serial stream) has been lost. This is based on an internal oscillator. The frequency of the oscillator may be selected. This feature may be controlled by the external pin or by register (see Table 8 and Table 9). Table 7. OSS_SEL and PDB Configuration (Deserializer Outputs) INPUTS (1) OUTPUTS SERIAL INPUT PDB OSS_SEL CLKOUT DO[23:0], CO1, CO2, CO3 X L L Z Z Z Z LOCK PASS X L H Z Z Z Z Static H L L L L L Static H H Z Z (1) L L Active H X Active Active H H If DO[23:0], CO[3:1] pin is strapped high, the output is pulled up. Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 Submit Documentation Feedback 29 DS92LV2421, DS92LV2422 SNLS321C - MAY 2010 - REVISED MAY 2016 www.ti.com Table 8. OSC (Oscillator) Mode -- Deserializer Output INPUTS OUTPUTS EMBEDDED CLK CLKOUT (1) See LOCK PASS OSC Output L L H Toggling Active H H Present (1) DO[23:0], CO1, CO2, CO3 Absent and OSC_SEL 000. PDB (DES) RIN (Diff.) active serial stream LOCK H Z DO[23:0], CO1,CO2,CO3 X H L L L L L L Z Z CLKOUT* (DES) Z Z Z Locking OFF Active Active C0 or C1 Error In Bit Stream (Loss of LOCK) OFF CONDITIONS: * RFB = L, and OSS_SEL Strap = L Figure 27. Deserializer Outputs With Output State Select Low (OSS_SEL = L) PDB (DES) RIN (Diff.) active serial stream Z LOCK X H L Z H L DO[23:0], CO1,CO2,CO3 Z Z Z CLKOUT* (DES) Z Z Z OFF Locking Active C0 or C1 Error In Bit Stream (Loss of LOCK) Active OFF CONDITIONS: * RFB = L, and OSS_SEL Strap = H Figure 28. Deserializer Outputs With Output State Select High (OSS_SEL = H) Table 9. OSC_SEL (Oscillator) Configuration OSC_SEL[2:0] INPUTS 30 OSC_SEL2 OSC_SEL1 OSC_SEL0 L L L Submit Documentation Feedback CLKOUT OSCILLATOR FREQUENCY Off - Feature Disabled - Default Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 DS92LV2421, DS92LV2422 www.ti.com SNLS321C - MAY 2010 - REVISED MAY 2016 Table 9. OSC_SEL (Oscillator) Configuration (continued) OSC_SEL[2:0] INPUTS OSC_SEL2 CLKOUT OSCILLATOR FREQUENCY OSC_SEL1 OSC_SEL0 L L H 50 MHz 40% L H L 25 MHz 40% L H H 16.7 MHz 40% H L L 12.5 MHz 40% H L H 10 MHz 40% H H L 8.3 MHz 40% H H H 6.3 MHz 40% PDB (DES) RIN (Diff.) active serial stream LOCK Z DO[23:0], CO1,CO2,CO3 Z CLKOUT* (DES) Z X H H L L Z L L Z L f f H PASS Z OFF Z Locking H Z L L Active C0 or C1 Error In Bit Stream (Loss of LOCK) Active OFF CONDITIONS: * RFB = L, OSS_SEL = H , and OSC_SEL not equal to 000. Figure 29. Deserializer Outputs With Output State High and CLKOUT Oscillator Option Enabled 7.3.4.5 Deserializer OP_LOW (Optional) The OP_LOW feature is used to hold the LVCMOS outputs (except for the LOCK output) at a low state. The user must toggle the OP_LOW set / reset register bit to release the outputs to the normal toggling state. NOTE The release of the outputs can only occur when LOCK is high. When the OP_LOW feature is enabled, anytime LOCK = low, the LVCMOS outputs toggle to a low state again. The OP_LOW strap pin feature is assigned to output PASS pin 42. Restrictions on other straps: 1. Other straps must not be used to keep the data and clock outputs at a true low state. Other features must be selected through I2C. 2. The OSS_SEL function is not available when OP_LOW is enabled (tied high). Outputs DO[23:0], CO[3:1], and CLKOUT are in TRI-STATE before PDB toggles high, because the OP_LOW strap value has not been recognized until the DS92LV2422 powers up. Figure 30 shows the user controlled release of OP_LOW and automatic reset of OP_LOW set on the falling edge of LOCK. Figure 31 shows the user controlled release of OP_LOW and manual reset of OP_LOW set. NOTE Manual reset of OP_LOW can only occur when LOCK is high. Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 Submit Documentation Feedback 31 DS92LV2421, DS92LV2422 SNLS321C - MAY 2010 - REVISED MAY 2016 PDB www.ti.com 2.0V LOCK OP_ LOW SET (Strap pin) User controlled User controlled OP_ LOW RELEASE/SET (Register) DO[23:0], CO3, CO2, CO1 TRISTATE ACTIVE ACTIVE CLKOUT TRISTATE ACTIVE ACTIVE Figure 30. OP_LOW Auto Set PDB 2.0V LOCK OP_LOW SET (Strap pin) User controlled User controlled OP_ LOW RELEASE/SET (Register) DO[23:0], CO3, CO2, CO1 TRISTATE ACTIVE CLKOUT TRISTATE ACTIVE Figure 31. OP_LOW Manual Set or Reset 7.3.4.6 Deserializer Clock Edge Select (RFB) The RFB pin determines the edge that the data is strobed on. If RFB is high, output data is strobed on the rising edge of CLKOUT. If RFB is low, data is strobed on the falling edge of CLKOUT. This allows for inter-operability with downstream devices. The deserializer output does not need to use the same edge as the serializer input. This feature may be controlled by the external pin or by register. 7.3.4.7 Deserializer Control Signal Filter (Optional) The deserializer provides an optional control signal (C3, C2, C1) filter that monitors the three control signals and eliminates any pulses or glitches that are 1 or 2 CLKOUT periods wide. Control signals must be 3 parallel clock periods wide (in its high or low state, regardless of which state is active). This is set by the CONFIG[1:0] strap option or by I2C register control. 32 Submit Documentation Feedback Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 DS92LV2421, DS92LV2422 www.ti.com SNLS321C - MAY 2010 - REVISED MAY 2016 7.3.4.8 Deserializer Low Frequency Optimization (LF_Mode) This feature may be controlled by the external pin or by register. 7.3.4.9 Deserializer Map Select This feature may be controlled by the external pin or by register. Table 10. Map Select Configuration INPUTS EFFECT MAP_SEL1 MAP_SEL0 L L Bit 4, Bit 5 on LSB DEFAULT L H LSB 0 or 1 H H or L LSB 0 7.3.4.10 Deserializer Strap Input Pins Configuration of the device may be done through configuration input pins and the strap input pins, or through the serial control bus. The strap input pins share select parallel bus output pins. They are used to load in configuration values during the initial power-up sequence of the device. Only a pullup on the pin is required when a high is desired. By default, the pad has an internal pulldown and bias low by itself. The recommended value of the pullup is 10 k to VDDIO; open (NC) for low, because no pulldown is required (internal pulldown). If using the serial control bus, no pullups are required. 7.3.4.11 Optional Serial Bus Control See Optional Serial Bus Control. 7.3.4.12 Optional BIST Mode See Built-In Self Test (BIST). 7.3.5 Built-In Self Test (BIST) An optional At-Speed Built-In Self Test (BIST) feature supports the testing of the high-speed serial link. This is useful in the prototype stage, equipment production, in-system test, and for system diagnostics. In BIST mode, only an input clock is required along with control to the serializer and deserializer BISTEN input pins. The serializer outputs a test pattern (PRBS-7) and drives the link at speed. The deserializer detects the PRBS-7 pattern and monitors it for errors. A PASS output pin toggles to flag any payloads that are received with 1 to 24 errors. Upon completion of the test, the result of the test is held on the PASS output until reset (new BIST test or power down). A high on PASS indicates NO ERRORS were detected. A low on PASS indicates one or more errors were detected. The duration of the test is controlled by the pulse width applied to the deserializer BISTEN pin. During the BIST duration, the deserializer data outputs toggle with a checkerboard pattern. Inter-operability is supported between this Channel Link II device and all Channel Link II generations (Gen 1, 2, 3). See Sample BIST Sequence for entering BIST mode and control. 7.3.5.1 Sample BIST Sequence See Figure 32 for the BIST mode flow diagram. Step 1: Place the DS92LV2421 serializer in BIST Mode by setting serializer BISTEN = H. For the DS92LV2421 serializer or DS99R421-Q1 FPD-Link II serializer, BIST Mode is enabled through the BISTEN pin. For the DS90C241 serializer or DS90UR241 serializer, BIST mode is entered by setting all the input data of the device to a low state. A CLKIN is required for BIST. When the deserializer detects the BIST mode pattern and command (DCA and DCB code), the data and control signal outputs are shut off. Step 2: Place the DS92LV2422 deserializer in BIST mode by setting BISTEN = H. The deserializer is now in BIST mode and checks the incoming serial payloads for errors. If an error in the payload (1 to 24) is detected, the PASS pin switches low for one half of the clock period. During the BIST test, the PASS output can be monitored and counted to determine the payload error rate. Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 Submit Documentation Feedback 33 DS92LV2421, DS92LV2422 SNLS321C - MAY 2010 - REVISED MAY 2016 www.ti.com Step 3: To stop BIST mode, the deserializer BISTEN pin is set low. The deserializer stops checking the data, and the final test result is held on the PASS pin. If the test ran error free, the PASS output is high. If there was one or more errors detected, the PASS output is low. The PASS output state is held until a new BIST is run, the device is RESET, or powered down. The BIST duration is user controlled by the duration of the BISTEN signal. Step 4: To return the link to normal operation, the serializer BISTEN input is set low. The Link returns to normal operation. Figure 33 shows the waveform diagram of a typical BIST test for two cases. Case 1 is error-free, and Case 2 shows one with multiple errors. In most cases, it is difficult to generate errors due to the robustness of the link (differential data transmission and so forth), thus they may be introduced by greatly extending the cable length, faulting the interconnect, or reducing signal condition enhancements (de-emphasis, VODSEL, or Rx equalization). Normal Step 1: SER in BIST BIST Wait Step 2: Wait, DES in BIST BIST start Step 3: DES in Normal Mode - check PASS BIST stop Step 4: SER in Normal Figure 32. BIST Mode Flow Diagram SER BISTEN (SER) DES Outputs BISTEN (DES) Case 1 - Pass CLKOUT (RFB = L) DO[23:0] CO1,CO2,CO3 DATA (internal) PASS Prior Result PASS PASS X X X FAIL Prior Result Normal PRBS Case 2 - Fail X = bit error(s) DATA (internal) BIST Result Held BIST Test BIST Duration Normal Figure 33. BIST Waveforms 34 Submit Documentation Feedback Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 DS92LV2421, DS92LV2422 www.ti.com SNLS321C - MAY 2010 - REVISED MAY 2016 7.3.5.2 BER Calculations It is possible to calculate the approximate Bit Error Rate (BER). The following is required: * Clock Frequency (MHz) * BIST Duration (seconds) * BIST Test Result (PASS) The BER is less than or equal to one over the product of 24 times the CLKOUT rate times the test duration. If we assume a 65-MHz clock, a 10-minute (600 seconds) test, and a PASS, the BER is 1.07 X 10E-12. BIST mode runs a check on the data payload bits. The LOCK pin also provides a link status. If the recovery of the C0 and C1 bits does not reconstruct the expected clock signal, the LOCK pin switches low. The combination of the LOCK and At-Speed BIST PASS pin provides a powerful tool for system evaluation and performance monitoring. 7.3.6 Optional Serial Bus Control The serializer and deserializer may also be configured by the use of a serial control bus that is I2C protocolcompatible. By default, the I2C Reg 0x00 = 0x00, and all configuration is set by control or strap pins. Writing reg 0x00 = 0x01 enables or allows configuration by registers; this overrides the control or strap pins. Multiple devices may share the serial control bus, because multiple addresses are supported (see Figure 34). The serial bus is comprised of three pins. The SCL is a serial bus clock input. The SDA is the serial bus data input or output signal. Both SCL and SDA signals require an external pullup resistor to VDDIO. For most applications, a 4.7-k pullup resistor to VDDIO may be used. The resistor value may be adjusted for capacitive loading and data rate requirements. The signals are either pulled high or driven low. 1.8V 10 k VDDIO ID[X] 4.7k HOST 4.7k RID SCL SCL SDA SDA SER or DES To other Devices Figure 34. Serial Control Bus Connection The third pin is the ID[X] pin. This pin sets one of four possible device addresses. Two different connections are possible: * The pin may be pulled to VDD (1.8 V, not VDDIO) with a 10-k resistor. * The pin may be pulled to VDD (1.8 V, not VDDIO) with a 10-k resistor and pulled down to ground with a recommended value RID resistor. This creates a voltage divider that sets the other three possible addresses. See Table 11 for the serializer and Table 12 for the deserializer. Do not tie ID[X] directly to VSS. Table 11. ID[X] Resistor Value - DS92LV2421 (Serializer) RESISTOR RID k (1) (5% TOL) (1) ADDRESS 7'b ADDRESS 8'b 0 APPENDED (WRITE) 0.47 7b' 110 1001 (h'69) 8b' 1101 0010 (h'D2) 2.7 7b' 110 1010 (h'6A) 8b' 1101 0100 (h'D4) 8.2 7b' 110 1011 (h'6B) 8b' 1101 0110 (h'D6) Open 7b' 110 1110 (h'6E) 8b' 1101 1100 (h'DC) RID 0 . Do not connect directly to VSS (GND). This is not a valid address. Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 Submit Documentation Feedback 35 DS92LV2421, DS92LV2422 SNLS321C - MAY 2010 - REVISED MAY 2016 www.ti.com Table 12. ID[X] Resistor Value - DS92LV2422 Deserializer RESISTOR RID k (1) (5% TOL) ADDRESS 7'b ADDRESS 8'b 0 APPENDED (WRITE) 0.47 7b' 111 0001 (h'71) 8b' 1110 0010 (h'E2) 2.7 7b' 111 0010 (h'72) 8b' 1110 0100 (h'E4) 8.2 7b' 111 0011 (h'73) 8b' 1110 0110 (h'E6) Open 7b' 111 0110 (h'76) 8b' 1110 1100 (h'EC) RID 0 . Do not connect directly to VSS (GND). This is not a valid address. (1) The serial bus protocol is controlled by START, START-repeated, and STOP phases. A START occurs when SCL transitions low while SDA is high. A STOP occurs when SDA transition high while SCL is also high (see Figure 35). SDA SCL S P START condition, or START repeat condition STOP condition Figure 35. START and STOP Conditions To communicate with a remote device, the host controller (master) sends the slave address and listens for a response from the slave. This response is referred to as an acknowledge bit (ACK). If a slave on the bus is addressed correctly, it Acknowledges (ACKs) the master by driving the SDA bus low. If the address doesn't match the slave address of a device, it Not-acknowledges (NACKs) the master by letting SDA be pulled high. ACKs also occur on the bus when data is being transmitted. When the master is writing data, the slave ACKs after every data byte is successfully received. When the master is reading data, the master ACKs after every data byte is received to let the slave know it wants to receive another data byte. When the master wants to stop reading, it NACKs after the last data byte and creates a stop condition on the bus. All communication on the bus begins with either a start condition or a repeated start condition. All communication on the bus ends with a stop condition. A READ is shown in Figure 36 and a WRITE is shown in Figure 37. NOTE During initial power-up, a delay of 10 ms is required before the I2C will respond. If the serial bus is not required, the three pins may be left open (NC). Register Address Slave Address S A 2 A 1 A 0 0 Slave Address a c k a c k A 2 S A 1 A 0 Data 1 a c k a c k P Figure 36. Serial Control Bus -- READ Register Address Slave Address S A 2 A 1 A 0 0 a c k Data a c k a c k P Figure 37. Serial Control Bus -- WRITE 36 Submit Documentation Feedback Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 DS92LV2421, DS92LV2422 www.ti.com SNLS321C - MAY 2010 - REVISED MAY 2016 7.4 Device Functional Modes 7.4.1 Serializer and Deserializer Operating Modes and Reverse Compatibility (CONFIG[1:0]) The DS92LV242x chipset is compatible with other single serial lane Channel Link II or FPD-Link II devices. Configuration modes are provided for reverse compatibility with the DS90C241 / DS90C124 chipset (FPD-Link II Generation 1) and also the DS90UR241 / DS90UR124 chipset (FPD-Link II Generation 2) by setting the respective mode with the CONFIG[1:0] pins on the serializer or deserializer as shown in Table 13 and Table 14. This selection also determines whether the control signal filter feature is enabled or disabled in the normal mode. This feature may be controlled by pin or by register. Table 13. DS92LV2421 Serializer Modes CONFIG1 CONFIG0 MODE COMPATIBLE DESERIALIZER DEVICE L L Normal Mode, Control Signal Filter disabled DS92LV2422, DS92LV2412, DS92LV0422, DS92LV0412 L H Normal Mode, Control Signal Filter enabled DS92LV2422, DS92LV2412, DS92LV0422, DS92LV0412 H L Reverse Compatibility Mode (FPD-Link II, GEN2) DS90UR124, DS99R124Q-Q1 H H Reverse Compatibility Mode (FPD-Link II, GEN1) DS90C124 Table 14. DS92LV2422 Deserializer Modes CONFIG1 CONFIG0 MODE COMPATIBLE SERIALIZER DEVICE L L Normal Mode, Control Signal Filter disabled DS92LV2421, DS92LV2411, DS92LV0421, DS92LV0411 L H Normal Mode, Control Signal Filter enabled DS92LV2421, DS92LV2411, DS92LV0421, DS92LV0411 H L Reverse Compatibility Mode (FPD-Link II, GEN2) DS90UR241, DS99R421-Q1 H H Reverse Compatibility Mode (FPD-Link II, GEN1) DS90C241 Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 Submit Documentation Feedback 37 DS92LV2421, DS92LV2422 SNLS321C - MAY 2010 - REVISED MAY 2016 www.ti.com 7.5 Register Maps Table 15. SERIALIZER -- Serial Bus Control Registers ADD (DEC) 0 1 ADD (HEX) 0 1 REGISTER NAME Serializer Config 1 BIT(S) R/W DEFAULT (BIN) 7 R/W 0 Reserved Reserved 6 R/W 0 Reserved Reserved 5 R/W 0 VODSEL 0: Low 1: High 4 R/W 0 RFB 0: Data latched on Falling edge of CLKIN 1: Data latched on Rising edge of CLKIN 38 2 DESCRIPTION 3:2 R/W 00 CONFIG 00: Normal Mode, Control Signal Filter Disabled 01: Normal Mode, Control Signal Filter Enabled 10: DS90UR124, DS99R124Q-Q1 ReverseCompatibility Mode (FPD-Link II, GEN2) 11: DS90C124 Reverse-Compatibility Mode (FPDLink II, GEN1) 1 R/W 0 SLEEP Note - not the same function as PowerDown (PDB) 0: Normal Mode 1: Sleep Mode - Register settings retained. 0 R/W 0 REG 0: Configurations set from control pins 1: Configuration set from registers (except I2C_ID) 7 R/W 0 REG ID 0: Address from ID[X] Pin 1: Address from Register ID[X] Serial Bus Device ID, Four IDs are: 7b '1101 001 (h'69) 7b '1101 010 (h'6A) 7b '1101 011 (h'6B) 7b '1101 110 (h'6E) All other addresses are reserved. Device ID 6:0 2 FUNCTION R/W 1101000 7:5 R/W 000 4 R/W 0 3:0 R/W 000 De-Emphasis Control Submit Documentation Feedback 000: set by external resistor 001: -1 dB 010: -2 dB De-Emphasis 011: -3.3 dB Setting 100: -5 dB 101: -6.7 dB 110: -9 dB 111: -12 dB De-Emphasis 0: De-emphasis enabled EN 1: De-emphasis disabled Reserved Reserved Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 DS92LV2421, DS92LV2422 www.ti.com SNLS321C - MAY 2010 - REVISED MAY 2016 Table 16. DESERIALIZER -- Serial Bus Control Registers ADD (DEC) 0 1 ADD (HEX) 0 1 REGISTER NAME BIT(S) R/W DEFAULT (BIN) 7 R/W 0 LF_MODE 0: 20 to 65 MHz SSCG Operation 1: 10 to 20 MHz SSCG Operation 6 R/W 0 OS_CLKOUT 0: Normal CLKOUT Slew Rate 1: Increased CLKOUT Slew Rate 5 R/W 0 OS_DATA 0: Normal DATA Slew Rate 1: Increased DATA Slew Rate 4 R/W 0 RFB 0: Data strobed on Falling edge of CLKOUT 1: Data strobed on Rising edge of CLKOUT 2 3:2 R/W 00 CONFIG 1 R/W 0 SLEEP Note - not the same function as PowerDown (PDB) 0: Normal Mode 1: Sleep Mode - Register settings retained. 0 R/W 0 REG Control 0: Configurations set from control pins or strap pins 1: Configurations set from registers (except I2C_ID) 7 R/W 0 REG ID 0: Address from ID[X] Pin 1: Address from Register ID[X] Serial Bus Device ID, Four IDs are: 7b '1110 001 (h'71) 7b '1110 010 (h'72) 7b '1110 011 (h'73) 7b '1110 110 (h'76) All other addresses are Reserved. OP_LOW 0: Set outputs state LOW (except LOCK) 1: Release output LOW state, outputs toggling normally Note: This register only works during LOCK = 1 OSS_SEL Output Sleep State Select 0: CLKOUT, DO[23:0], CO1, CO2, CO3 = L, LOCK = Normal, PASS = H 1: CLKOUT, DO[23:0], CO1, CO2, CO3 = Tri-State, LOCK = Normal, PASS = H Special for Reverse-Compatibility Mode 00: Bit 4, 5 on LSB 01: LSB zero if all data is zero; one if any data is one 10: LSB zero 11: LSB zero Slave ID Deserializer Features 1 DESCRIPTION 00: Normal Mode, Control Signal Filter Disabled 01: Normal Mode, Control Signal Filter Enabled 10: DS90UR241, DS99R241-Q1 ReverseCompatibility Mode (FPD-Link II, GEN2) 11: DS90C241 Reverse-Compatibility Mode (FPDLink II, GEN1) Deserializer Config 1 6:0 R/W 1110000 7 R/W 0 6 2 FUNCTION R/W 0 5:4 R/W 00 MAP_SEL 3 R/W 0 0: Strap will determine whether OP_LOW feature is OP_LOW ON or OFF Strap Bypass 1: Turns OFF OP_LOW feature 2:0 R/W 00 OSC_SEL 000: 001: 010: 011: 100: 101: 110: 111: Disable 50 MHz 40% 25 MHz 40% 16.7 MHz 40% 12.5 MHz 40% 10 MHz 40% 8.3 MHz 40% 6.3 MHz 40% Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 Submit Documentation Feedback 39 DS92LV2421, DS92LV2422 SNLS321C - MAY 2010 - REVISED MAY 2016 www.ti.com Table 16. DESERIALIZER -- Serial Bus Control Registers (continued) ADD (DEC) 3 ADD (HEX) 3 REGISTER NAME BIT(S) 40 4 DEFAULT (BIN) 7:5 R/W 000 4 R/W 0 FUNCTION ROUT Config R/W 0000 DESCRIPTION EQ Gain 000: 1.625 dB 001: 3.25 dB 010: 4.87 dB 011: 6.5 dB 100: 8.125 dB 101: 9.75 dB 110: 11.375 dB 111: 13 dB EQ Enable 0: EQ = disable 1: EQ = enable SSC If LF_MODE = 0, then: 000: SSCG disable 0001: fdev = 0.5%, fmod 0010: fdev = 1.0%, fmod 0011: fdev = 1.5%, fmod 0100: fdev = 2.0%, fmod 0101: fdev = 0.5%, fmod 0110: fdev = 1.0%, fmod 0111: fdev = 1.5%, fmod 1000: fdev = 2.0%, fmod 1001: fdev = 0.5%, fmod 1010: fdev = 1.0%, fmod 1011: fdev = 1.5%, fmod 1100: fdev = 2.0%, fmod 1101: fdev = 0.5%, fmod 1110: fdev = 1.0%, fmod 1111: fdev = 1.5%, fmod If LF_MODE = 1, then: 000: SSCG disable 0001: fdev = 0.5%, fmod 0010: fdev = 1.0%, fmod 0011: fdev = 1.5%, fmod 0100: fdev = 2.0%, fmod 0101: fdev = 0.5%, fmod 0110: fdev = 1.0%, fmod 0111: fdev = 1.5%, fmod 1000: fdev = 2.0%, fmod 1001: fdev = 0.5%, fmod 1010: fdev = 1.0%, fmod 1011: fdev = 1.5%, fmod 1100: fdev = 2.0%, fmod 1101: fdev = 0.5%, fmod 1110: fdev = 1.0%, fmod 1111: fdev = 1.5%, fmod Deserializer Features 2 3:0 4 R/W = CLK/2168 = CLK/2168 = CLK/2168 = CLK/2168 = CLK/1300 = CLK/1300 = CLK/1300 = CLK/1300 = CLK/868 = CLK/868 = CLK/868 = CLK/868 = CLK/650 = CLK/650 = CLK/650 = CLK/620 = CLK/620 = CLK/620 = CLK/620 = CLK/370 = CLK/370 = CLK/370 = CLK/370 = CLK/258 = CLK/258 = CLK/258 = CLK/258 = CLK/192 = CLK/192 = CLK/192 7 R/W 0 Repeater Enable 0: Output ROUT = disable 1: Output ROUT = enable 6:0 R/W 0000000 Reserved Reserved Submit Documentation Feedback Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 DS92LV2421, DS92LV2422 www.ti.com SNLS321C - MAY 2010 - REVISED MAY 2016 8 Application and Implementation NOTE Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI's customers are responsible for determining suitability of components for their purposes. Customers should validate and test their design implementation to confirm system functionality. 8.1 Application Information 8.1.1 Display Application The DS92LV242x chipset is intended for interface between a host (graphics processor) and a display. It supports a 24-bit color depth (RGB888) and up to 1024 x 768 display formats. In a RGB888 application, 24 color bits (D[23:0]), Pixel Clock (CLKIN), and three control bits (C1, C2, C3) are supported across the serial link with CLKIN rates from 10 to 75 MHz. The chipset may also be used in 18-bit color applications. In this application, three to six general-purpose signals may also be sent from host to display. The deserializer is expected to be placed close to its target device. The interconnect between the deserializer and the target device is typically in the 1 to 3 inch separation range. The input capacitance of the target device is expected to be in the 5 pF to 10 pF range. Take care of the CLKOUT output trace, as this signal is edge sensitive and strobes the data. It is also assumed that the fanout of the deserializer is one. If additional loads need to be driven, a logic buffer or mux device is recommended. 8.1.2 Live Link Insertion The serializer and deserializer devices support live pluggable applications. The automatic receiver lock to random data plug and go hot insertion capability allows the DS92LV2422 to attain lock to the active data stream during a live insertion event. 8.1.3 Alternate Color / Data Mapping Color Mapped Data Pin names are provided to specify a recommended mapping for 24-bit color applications. Seven [7] is assumed to be the MSB, and Zero [0] is assumed to be the LSB. While this is recommended, it is not required. When connecting to earlier generations of FPD-Link II serializer and deserializer devices, a color mapping review is recommended to ensure the correct connectivity is obtained. Table 17 provides examples for interfacing to 18-bit applications with or without the video control signals embedded. The DS92LV2422 deserializer provides additional flexibility with the MAP_SEL feature as well. Table 17. Alternate Color and Data Mapping 18-BIT RGB 18-BIT RGB 24-BIT RGB 2421 PIN NAME 2422 PIN NAME 24-BIT RGB 18-BIT RGB 18-BIT RGB LSB R0 GP0 R0 DI0 DO0 R0 GP0 LSB R0 R1 GP1 R1 DI1 DO1 R1 GP1 R1 R2 R0 R2 DI2 DO2 R2 R0 R2 R3 R1 R3 DI3 DO3 R3 R1 R3 R4 R2 R4 DI4 DO4 R4 R2 R4 MSB R5 R3 R5 DI5 DO5 R5 R3 MSB R5 LSB G0 R4 R6 DI6 DO6 R6 R4 LSB G0 G1 R5 R7 DI7 DO7 R7 R5 G1 G2 GP2 G0 DI8 DO8 G0 GP2 G2 G3 GP3 G1 DI9 DO9 G1 GP3 G3 G4 G0 G2 DI10 DO10 G2 G0 G4 MSB G5 G1 G3 DI11 DO11 G3 G1 MSB G5 LSB B0 G2 G4 DI12 DO12 G4 G2 LSB0 B1 G3 G5 DI13 DO13 G5 G3 B1 Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 Submit Documentation Feedback 41 DS92LV2421, DS92LV2422 SNLS321C - MAY 2010 - REVISED MAY 2016 www.ti.com Application Information (continued) Table 17. Alternate Color and Data Mapping (continued) 18-BIT RGB 18-BIT RGB 24-BIT RGB 2421 PIN NAME 2422 PIN NAME 24-BIT RGB 18-BIT RGB 18-BIT RGB B2 G4 G6 DI14 DO14 G6 G4 B2 B3 G5 G7 DI15 DO15 G7 G5 B3 B4 GP4 B0 DI16 DO16 B0 GP4 B4 MSB B5 GP5 B1 DI17 DO17 B1 GP5 MSB B5 HS B0 B2 DI18 DO18 B2 B0 HS VS B1 B3 DI19 DO19 B3 B1 VS DE B2 B4 DI20 DO20 B4 B2 DE GP0 B3 B5 DI21 DO21 B5 B3 GP0 GP1 B4 B6 DI22 DO22 B6 B4 GP1 GP2 B5 B7 DI23 DO23 B7 B5 GP2 GND HS HS CI1 CO1 HS HS GND GND GND VS VS CI2 CO2 VS VS GND DE DE CI3 CO3 DE DE GND Scenario 3 (1) Scenario 2 (2) Scenario 1 (3) Scenario 1 (3) Scenario 2 (2) Scenario 3 (1) (1) (2) (3) 2421 Pin Name 2422 Pin Name Scenario 3 supports an 18-bit RGB color mapping, 3 un-embedded video control signals, and up to three general-purpose signals. Scenario 2 supports an 18-bit RGB color mapping, 3 embedded video control signals, and up to six general-purpose signals. Scenario 1 supports the 24-bit RGB color mapping, along with the 3 embedded video control signals. This is the native mode for the chipset. 8.2 Typical Applications 8.2.1 DS92LV2421 Typical Connection Figure 38 shows a typical application of the DS92LV2421 serializer in pin control mode for a 24-bit application. The LVDS outputs require 100-nF AC-coupling capacitors to the line. The line driver includes internal termination. Bypass capacitors are placed near the power supply pins. At a minimum, four 0.1-F capacitors and a 4.7-F capacitor must be used for local device bypassing. System GPO (General Purpose Output) signals control the PDB and BISTEN pins. In this application, the RFB pin is tied low to latch data on the falling edge of the CLKIN. The application assumes connection to the companion deserializer (DS92LV2422), and therefore the configuration pins CONFIG[1:0] are also both tied low. In this example, the cable is long, and therefore the VODSEL pin is tied high and a De-Emphasis value is selected by the resistor R1. The interface to the host is with 1.8-V LVCMOS levels, thus the VDDIO pin is connected also to the 1.8-V rail. The optional serial bus control is not used in this example, thus the SCL, SDA, and ID[X] pins are left open. A delay cap is placed on the PDB signal to delay the enabling of the device until power is stable. 42 Submit Documentation Feedback Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 DS92LV2421, DS92LV2422 www.ti.com SNLS321C - MAY 2010 - REVISED MAY 2016 Typical Applications (continued) DS92LV2421 (SER) VDDIO VDDIO C9 C7 FB1 VDDTX VDDHS C3 DI0 DI1 DI2 DI3 DI4 DI5 DI6 DI7 C11 CI1 CI2 CI3 LVCMOS Control Interface FB2 C8 C10 C5 FB3 C6 FB4 VDDL C1 Serial Channel Link II Interface DOUT+ DOUTC2 DI16 DI17 DI18 DI19 DI20 DI21 DI22 DI23 CLKIN C4 VDDP DI8 DI9 DI10 DI11 DI12 DI13 DI14 DI15 LVCMOS Parallel Video Interface 1.8V VDDIO VODSEL De-Emph 1.8V R1 10k BISTEN PDB ID[X] SCL SDA C12 CONFIG1 CONFIG0 RFB RID NOTE: C1-C2 = 0.1 PF (50 WV) C3-C8 = 0.1 PF C9-11 = 4.7 PF C12 = >10 PF R1 (cable specific) RID (Use Recommended ID[x] Resistor Value) FB1-FB4: Impedance = 1 k:, low DC resistance (<1:) RES2 RES1 RES0 DAP (GND) Copyright (c) 2016, Texas Instruments Incorporated Figure 38. DS92LV2421 Typical Connection Diagram - Pin Control 8.2.1.1 Design Requirements For this example, Table 18 lists the design parameters. Table 18. Design Parameters PARAMETER EXAMPLE VALUE VDDIO 1.8 V to 3.3 V VDDL, VDDP, VDDHS, VDDTX 1.8 V AC-Coupling Capacitor for DOUT 100 nF Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 Submit Documentation Feedback 43 DS92LV2421, DS92LV2422 SNLS321C - MAY 2010 - REVISED MAY 2016 www.ti.com 8.2.1.2 Detailed Design Procedure The DOUT outputs require 100-nF AC-coupling capacitors to the line. The power supply filter capacitors are placed near the power supply pins. A smaller capacitance capacitor must be located closer to the power supply pins. The VODSEL pin is tied to VDDIO for the long cable application. The de-emphasis pin may connect a resistor to ground. Refer to Table 3. The PDB and BISTEN pins are assumed to be controlled by a microprocessor. The PDB must remain in a low state until all power supply voltages reach the final voltage. The RFB pin is tied low to latch data on the falling edge of the PCLK and tied high for the rising clock edge. The CONFIG[1:0] pins are set depending on operating modes and backward compatibility. The SCL, SDA, and ID[X] pins are left open when these serial bus control pins are unused. The RES[2:0] pins and DAP must be tied to ground. 8.2.1.3 Application Curve Figure 39. Eye Diagram at CLK = 20 MHz 8.2.2 DS92LV2422 Typical Connection Figure 40 shows a typical application of the DS92LV2422 deserializer in pin or strap control mode for a 24-bit application. The LVDS inputs use 100-nF coupling capacitors to the line, and the receiver provides internal termination. Bypass capacitors are placed near the power supply pins. At a minimum, seven 0.1-F capacitors and two 4.7-F capacitors must be used for local device bypassing. System General Purpose Output (GPO) signals control the PDB and the BISTEN pins. In this application, the RFB pin is tied low to strobe the data on the falling edge of the CLKOUT. Because the device is in pin or strap control mode, four 10-k pullup resistors are used on the parallel output bus to select the desired device features. CONFIG[1:0] is set to 01'b for normal mode with control signal filter enabled, and this is accomplished with the strap pullup on DO23. The receiver input equalizer is also enabled and set to provide 7.5 dB of gain, and this is accomplished with EQ[3:0] set to 1001'b with strap pullups on DO12 and DO15. To reduce parallel bus EMI, the SSCG feature is enabled and set to fmod = CLK/2168 and 1% with SSC[3:0] set to 0010'b and a strap pullup on DO4. The desired features are set with the use of the four pullup resistors. The interface to the target display is with 3.3-V LVCMOS levels, thus the VDDIO pin is connected to the 3.3-V rail. The optional serial bus control is not used in this example, thus the SCL, SDA and ID[X] pins are left open. A delay cap is placed on the PDB signal to delay the enabling of the device until power is stable. 44 Submit Documentation Feedback Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 DS92LV2421, DS92LV2422 www.ti.com SNLS321C - MAY 2010 - REVISED MAY 2016 DS92LV2422 (DES) 1.8V VDDL C13 C11 VDDIO VDDIO C8 C3 VDDSC C12 C14 VDDIO C9 C4 VDDPR VDDIO C10 C5 VDDR C15 C6 VDDIR VDDIO EXAMPLE: STRAP Input Pull-Ups (10k) VDDCMLO C16 C7 C1 Serial Channel Link II Interface RIN+ RINCMF C2 C17 TP_A ROUT+ ROUT- TP_B BISTEN PDB Host Control C18 1.8V 10k ID[X] SCL SDA RID NOTE: C1 - C2 = 0.1 PF (50 WV) C3 - C12 = 0.1 PF C13, C16 = 4.7 PF C17, C18 = >10 PF RID (Use Recommended ID[x] Resistor Value) FB1-FB4: Impedance = 1 k:, low DC resistance (<1:) 8 NC DO0 DO1 DO2 DO3 DO4 DO5 DO6 DO7 DO8 DO9 DO10 DO11 DO12 DO13 DO14 DO15 LVCMOS Parallel Video Interface DO16 DO17 DO18 DO19 DO20 DO21 DO22 DO23 CO1 CO2 CO3 CLKOUT RES DAP (GND) LOCK PASS Copyright (c) 2016, Texas Instruments Incorporated Figure 40. DS92LV2422 Typical Connection Diagram -- Pin Control 8.2.2.1 Design Requirements For this example, Table 19 lists the design parameters. Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 Submit Documentation Feedback 45 DS92LV2421, DS92LV2422 SNLS321C - MAY 2010 - REVISED MAY 2016 www.ti.com Table 19. Design Parameters PARAMETER EXAMPLE VALUE VDDIO 1.8 V to 3.3 V VDDL, VDDSC, VDDPR, VDDR, VDDIR, VDDCMLO 1.8 V AC-Coupling Capacitor for DOUT 100 nF 8.2.2.2 Detailed Design Procedure The RIN inputs require 100-nF AC-coupling capacitors to the line. The power supply filter capacitors are placed near the power supply pins. A smaller capacitance capacitor must be placed closer to the power supply pins. The device has 22 control and configuration pins that are called strap pins. These pins include an internal pulldown. For a high state, use a 10-k resistor pullup to VDDIO. The PDB and BISTEN pins are assumed to be controlled by a microprocessor. The PDB has to be in a low state until all power supply voltages reach the final voltage. The SCL, SDA, and ID[X] pins are left open when these serial bus control pins are unused. The RES pin and DAP must be tied to ground. 8.2.2.3 Application Curves Figure 41. Eye Diagram at CLK = 45 MHz Figure 42. Eye Diagram at CLK = 65 MHz 9 Power Supply Recommendations 9.1 Power-Up Requirements and PDB Pin The VDD (VDDn and VDDIO) supply ramp must be faster than 1.5 ms with a monotonic rise. If slower then 1.5 ms, then a capacitor on the PDB pin is needed to ensure PDB arrives after all the VDD have settled to the recommended operating voltage. When PDB pin is pulled to VDDIO, TI recommends using a 10-k pullup and a 22-F capacitor to GND to delay the PDB input signal. 46 Submit Documentation Feedback Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 DS92LV2421, DS92LV2422 www.ti.com SNLS321C - MAY 2010 - REVISED MAY 2016 10 Layout 10.1 Layout Guidelines Circuit board layout and stack-up for the LVDS serializer and deserializer devices must be designed to provide low-noise power feed to the device. Good layout practice also separates high frequency or high-level inputs and outputs to minimize unwanted stray noise pickup, feedback, and interference. Power system performance may be greatly improved by using thin dielectrics (2 to 4 mils) for power or ground sandwiches. This arrangement provides plane capacitance for the PCB power system with low-inductance parasitics, which has proven especially effective at high frequencies and makes the value and placement of external bypass capacitors less critical. External bypass capacitors must include both RF ceramic and tantalum electrolytic types. RF capacitors may use values in the range of 0.01 F to 0.1 F. Tantalum capacitors may be in the 2.2 F to 10 F range. Voltage rating of the tantalum capacitors must be at least 5x the power supply voltage being used. Surface-mount capacitors are recommended due to their smaller parasitics. When using multiple capacitors per supply pin, place the smaller value closer to the pin. A large bulk capacitor is recommend at the point of power entry. This is typically in the 50 F to 100 F range and smooths low frequency switching noise. TI recommends connecting power and ground pins directly to the power and ground planes with bypass capacitors connected to the plane, with vias on both ends of the capacitor. Connecting power or ground pins to an external bypass capacitor increases the inductance of the path. A small body size X7R chip capacitor, such as 0603, is recommended for external bypass. Its small body size reduces the parasitic inductance of the capacitor. The user must pay attention to the resonance frequency of these external bypass capacitors, usually in the range of 20 to 30 MHz. To provide effective bypassing, multiple capacitors are often used to achieve low impedance between the supply rails over the frequency of interest. At high frequency, it is also a common practice to use two vias from power and ground pins to the planes, reducing the impedance at high frequency. Some devices provide separate power and ground pins for different portions of the circuit. This is done to isolate switching noise effects between different sections of the circuit. Separate planes on the PCB are typically not required. Pin description tables typically provide guidance on which circuit blocks are connected to which power pin pairs. In some cases, an external filter may be used to provide clean power to sensitive circuits such as PLLs. Use at least a four-layer board with a power and ground plane. Place LVCMOS signals away from the CML lines to prevent coupling from the LVCMOS lines to the CML lines. Closely-coupled differential lines of 100 are typically recommended for LVDS interconnects. The closely coupled lines help to ensure that coupled noise appears as common mode and thus is rejected by the receivers. The tightly coupled lines also radiate less. 10.1.1 WQFN (LLP) Stencil Guidelines Stencil parameters such as aperture area ratio and the fabrication process have a significant impact on paste deposition. Inspection of the stencil prior to placement of the LLP (WQFN) package is highly recommended to improve board assembly yields. If the via and aperture openings are not carefully monitored, the solder may flow unevenly through the DAP. Stencil parameters for aperture opening and via locations are shown below: Figure 43. No Pullback LLP, Single Row Reference Diagram Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 Submit Documentation Feedback 47 DS92LV2421, DS92LV2422 SNLS321C - MAY 2010 - REVISED MAY 2016 www.ti.com Layout Guidelines (continued) Table 20. No Pullback LLP Stencil Aperture Summary for DS92LV2421 and DS92LV2422 STENCIL DAP APERTURE (mm) NUMBER OF DAP APERTURE OPENINGS GAP BETWEEN DAP APERTURE (Dim A mm) 0.25 x 0.7 1.1 x 1.1 16 0.2 0.25 x 0.9 1.16 x 1.16 25 0.3 DEVICE PIN COUNT MKT DWG PCB I/O PAD SIZE (mm) PCB PITCH (mm) PCB DAP SIZE (mm) STENCIL I/O APERTURE (mm) DS92LV2421 48 SQA48A 0.25 x 0.6 0.5 5.1 x 5.1 DS92LV2422 60 SQA60B 0.25 x 0.8 0.5 7.2 x 7.2 Figure 44. 48-Pin WQFN Stencil Example of Via and Opening Placement Information on the WQFN style package is provided in Leadless Leadframe Package (LLP) Application Report (SNOA401). 10.1.2 Transmission Media The serializer and deserializer chipset is intended to be used in a point-to-point configuration through a PCB trace or through twisted pair cable. The serializer and deserializer provide internal terminations for a clean signaling environment. The interconnect for CML must present a differential impedance of 100 . Use cables and connectors that have matched differential impedance to minimize impedance discontinuities. Shielded or unshielded cables may be used depending upon the noise environment and application requirements. 10.1.3 LVDS Interconnect Guidelines See AN-1108 Channel-Link PCB and Interconnect Design-In Guidelines (SNLA008) and AN-905 Transmission Line RAPIDESIGNER Operation and Applications Guide (SNLA035) for full details. * Use 100- coupled differential pairs * Use the S, 2S, 3S rule in spacings - S = space between the pair - 2S = space between pairs - 3S = space to LVCMOS signal * Minimize the number of vias * Use differential connectors when operating above 500-Mbps line speed * Maintain balance of the traces * Minimize skew within the pair 48 Submit Documentation Feedback Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 DS92LV2421, DS92LV2422 www.ti.com * SNLS321C - MAY 2010 - REVISED MAY 2016 Terminate as close to the TX outputs and RX inputs as possible Additional general guidance can be found in the LVDS Owner's Manual, available in PDF format from the TI web site at: www.ti.com/lvds. 10.2 Layout Example The following PCB layout examples are derived from the layout design of the LV24EVK01 Evaluation Module. These graphics and additional layout description are used to demonstrate both proper routing and proper solder techniques when designing in the serializer and deserializer pair. Figure 45. DS92LV2421 Serializer Example Layout Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 Submit Documentation Feedback 49 DS92LV2421, DS92LV2422 SNLS321C - MAY 2010 - REVISED MAY 2016 www.ti.com Layout Example (continued) Figure 46. DS92LV2422 Deserializer Example Layout 50 Submit Documentation Feedback Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 DS92LV2421, DS92LV2422 www.ti.com SNLS321C - MAY 2010 - REVISED MAY 2016 11 Device and Documentation Support 11.1 Device Support 11.1.1 Third-Party Products Disclaimer TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE. 11.1.2 Development Support For development support see the following: LVDS Owner's Manual, www.ti.com/lvds 11.2 Documentation Support 11.2.1 Related Documentation For related documentation see the following: * Absolute Maximum Ratings for Soldering, SNOA549 * Leadless Leadframe Package (LLP) Application Report, SNOA401 * AN-1108 Channel-Link PCB and Interconnect Design-In Guidelines, SNLA008 * AN-905 Transmission Line RAPIDESIGNER Operation and Applications Guide, SNLA035 11.3 Related Links The table below lists quick access links. Categories include technical documents, support and community resources, tools and software, and quick access to sample or buy. Table 21. Related Links PARTS PRODUCT FOLDER SAMPLE & BUY TECHNICAL DOCUMENTS TOOLS & SOFTWARE SUPPORT & COMMUNITY DS92LV2421 Click here Click here Click here Click here Click here DS92LV2422 Click here Click here Click here Click here Click here 11.4 Community Resource The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of Use. TI E2ETM Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help solve problems with fellow engineers. Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and contact information for technical support. 11.5 Trademarks E2E is a trademark of Texas Instruments. All other trademarks are the property of their respective owners. 11.6 Electrostatic Discharge Caution These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 Submit Documentation Feedback 51 DS92LV2421, DS92LV2422 SNLS321C - MAY 2010 - REVISED MAY 2016 www.ti.com 11.7 Glossary SLYZ022 -- TI Glossary. This glossary lists and explains terms, acronyms, and definitions. 12 Mechanical, Packaging, and Orderable Information The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation. 52 Submit Documentation Feedback Copyright (c) 2010-2016, Texas Instruments Incorporated Product Folder Links: DS92LV2421 DS92LV2422 PACKAGE OPTION ADDENDUM www.ti.com 6-Feb-2020 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (C) Device Marking (4/5) DS92LV2421SQ/NOPB ACTIVE WQFN RHS 48 1000 Green (RoHS & no Sb/Br) SN Level-3-260C-168 HR -40 to 85 LV2421SQ DS92LV2421SQE/NOPB ACTIVE WQFN RHS 48 250 Green (RoHS & no Sb/Br) SN Level-3-260C-168 HR -40 to 85 LV2421SQ DS92LV2421SQX/NOPB ACTIVE WQFN RHS 48 2500 Green (RoHS & no Sb/Br) SN Level-3-260C-168 HR -40 to 85 LV2421SQ DS92LV2422SQ/NOPB ACTIVE WQFN NKB 60 1000 Green (RoHS & no Sb/Br) SN Level-3-260C-168 HR -40 to 85 LV2422SQ DS92LV2422SQE/NOPB ACTIVE WQFN NKB 60 250 Green (RoHS & no Sb/Br) SN Level-3-260C-168 HR -40 to 85 LV2422SQ DS92LV2422SQX/NOPB ACTIVE WQFN NKB 60 2000 Green (RoHS & no Sb/Br) SN Level-3-260C-168 HR -40 to 85 LV2422SQ (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may reference these types of products as "Pb-Free". RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption. Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based flame retardants must also meet the <=1000ppm threshold requirement. (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. (4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. Addendum-Page 1 Samples PACKAGE OPTION ADDENDUM www.ti.com 6-Feb-2020 (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 20-Sep-2016 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing DS92LV2421SQ/NOPB WQFN RHS 48 DS92LV2421SQE/NOPB WQFN RHS DS92LV2421SQX/NOPB WQFN RHS DS92LV2422SQ/NOPB WQFN DS92LV2422SQE/NOPB DS92LV2422SQX/NOPB SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant 1000 330.0 16.4 7.3 7.3 1.3 12.0 16.0 Q1 48 250 178.0 16.4 7.3 7.3 1.3 12.0 16.0 Q1 48 2500 330.0 16.4 7.3 7.3 1.3 12.0 16.0 Q1 NKB 60 1000 330.0 16.4 9.3 9.3 1.3 12.0 16.0 Q1 WQFN NKB 60 250 178.0 16.4 9.3 9.3 1.3 12.0 16.0 Q1 WQFN NKB 60 2000 330.0 16.4 9.3 9.3 1.3 12.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 20-Sep-2016 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) DS92LV2421SQ/NOPB WQFN RHS 48 1000 367.0 367.0 38.0 DS92LV2421SQE/NOPB WQFN RHS 48 250 210.0 185.0 35.0 DS92LV2421SQX/NOPB WQFN RHS 48 2500 367.0 367.0 38.0 DS92LV2422SQ/NOPB WQFN NKB 60 1000 367.0 367.0 38.0 DS92LV2422SQE/NOPB WQFN NKB 60 250 210.0 185.0 35.0 DS92LV2422SQX/NOPB WQFN NKB 60 2000 367.0 367.0 38.0 Pack Materials-Page 2 PACKAGE OUTLINE NKB0060B VQFN - 0.8 mm max height SCALE 1.500 PLASTIC QUAD FLATPACK - NO LEAD 9.1 8.9 B A PIN 1 INDEX AREA 9.1 8.9 0.8 0.7 C SEATING PLANE 0.05 0.00 0.08 C 2X 7 6.3 0.1 EXPOSED THERMAL PAD SYMM 16 15 31 SYMM 61 2X 7 1 56X 0.5 PIN 1 ID (0.1) TYP 30 45 60 46 0.7 60X 0.5 60X 0.3 0.2 0.1 0.05 C A B 4214995/A 03/2018 NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. The package thermal pad must be soldered to the printed circuit board for thermal and mechanical performance. www.ti.com EXAMPLE BOARD LAYOUT NKB0060B VQFN - 0.8 mm max height PLASTIC QUAD FLATPACK - NO LEAD ( 6.3) SYMM 60X (0.8) 46 60 SEE SOLDER MASK DETAIL 60X (0.25) 1 45 56X (0.5) (1.1) TYP (1.2) TYP (R0.05) TYP ( 0.2) TYP VIA SYMM 61 (0.6) TYP 15 (8.6) 31 16 30 (0.6) TYP (1.2) TYP (1.1) TYP (8.6) LAND PATTERN EXAMPLE EXPOSED METAL SHOWN SCALE: 8X 0.07 MIN ALL AROUND 0.07 MAX ALL AROUND METAL UNDER SOLDER MASK METAL EDGE EXPOSED METAL SOLDER MASK OPENING EXPOSED METAL NON SOLDER MASK DEFINED (PREFERRED) SOLDER MASK OPENING SOLDER MASK DEFINED SOLDER MASK DETAILS 4214995/A 03/2018 NOTES: (continued) 4. This package is designed to be soldered to a thermal pad on the board. For more information, see Texas Instruments literature number SLUA271 (www.ti.com/lit/slua271). 5. Vias are optional depending on application, refer to device data sheet. If any vias are implemented, refer to their locations shown on this view. It is recommended that vias under paste be filled, plugged or tented. www.ti.com EXAMPLE STENCIL DESIGN NKB0060B VQFN - 0.8 mm max height PLASTIC QUAD FLATPACK - NO LEAD 25X ( 1) (1.2) TYP 60X (0.8) 60 46 60X (0.25) 1 45 56X (0.5) (R0.05) TYP (1.2) TYP 61 SYMM (8.6) 15 31 30 16 SYMM (8.6) SOLDER PASTE EXAMPLE BASED ON 0.125 MM THICK STENCIL SCALE: 8X EXPOSED PAD 61 63% PRINTED SOLDER COVERAGE BY AREA UNDER PACKAGE 4214995/A 03/2018 NOTES: (continued) 6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. www.ti.com PACKAGE OUTLINE RHS0048A WQFN - 0.8 mm max height SCALE 1.800 PLASTIC QUAD FLATPACK - NO LEAD 7.15 6.85 A B PIN 1 INDEX AREA 0.5 0.3 7.15 6.85 0.30 0.18 DETAIL OPTIONAL TERMINAL TYPICAL 0.8 0.7 C SEATING PLANE 0.05 0.00 0.08 C 2X 5.5 (0.2) 5.1 0.1 (A) TYP 24 13 44X 0.5 DIM A OPT 1 OPT 2 (0.1) (0.2) 12 25 EXPOSED THERMAL PAD 2X 5.5 49 SYMM SEE TERMINAL DETAIL 1 PIN 1 ID (OPTIONAL) 36 48 37 SYMM 48X 0.5 0.3 48X 0.30 0.18 0.1 0.05 C A B 4214990/B 04/2018 NOTES: 1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing per ASME Y14.5M. 2. This drawing is subject to change without notice. 3. The package thermal pad must be soldered to the printed circuit board for thermal and mechanical performance. www.ti.com EXAMPLE BOARD LAYOUT RHS0048A WQFN - 0.8 mm max height PLASTIC QUAD FLATPACK - NO LEAD ( 5.1) SYMM 37 48 48X (0.6) 1 36 48X (0.25) (1.05) TYP 44X (0.5) (1.25) TYP 49 SYMM (6.8) (R0.05) TYP ( 0.2) TYP VIA 25 12 13 24 (1.25) TYP (1.05) TYP (6.8) LAND PATTERN EXAMPLE EXPOSED METAL SHOWN SCALE:12X 0.07 MIN ALL AROUND 0.07 MAX ALL AROUND SOLDER MASK OPENING METAL EDGE EXPOSED METAL SOLDER MASK OPENING EXPOSED METAL NON SOLDER MASK DEFINED (PREFERRED) METAL UNDER SOLDER MASK SOLDER MASK DEFINED SOLDER MASK DETAILS 4214990/B 04/2018 NOTES: (continued) 4. This package is designed to be soldered to a thermal pad on the board. For more information, see Texas Instruments literature number SLUA271 (www.ti.com/lit/slua271). 5. Vias are optional depending on application, refer to device data sheet. If any vias are implemented, refer to their locations shown on this view. It is recommended that vias under paste be filled, plugged or tented. www.ti.com EXAMPLE STENCIL DESIGN RHS0048A WQFN - 0.8 mm max height PLASTIC QUAD FLATPACK - NO LEAD (0.625) TYP (1.25) TYP 37 48 48X (0.6) 1 36 49 48X (0.25) 44X (0.5) (1.25) TYP (0.625) TYP SYMM (6.8) (R0.05) TYP METAL TYP 25 12 13 16X ( 1.05) 24 SYMM (6.8) SOLDER PASTE EXAMPLE BASED ON 0.125 mm THICK STENCIL EXPOSED PAD 49 68% PRINTED SOLDER COVERAGE BY AREA UNDER PACKAGE SCALE:15X 4214990/B 04/2018 NOTES: (continued) 6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate design recommendations. www.ti.com IMPORTANT NOTICE AND DISCLAIMER TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES "AS IS" AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD PARTY INTELLECTUAL PROPERTY RIGHTS. These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you permission to use these resources only for development of an application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these resources. TI's products are provided subject to TI's Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on ti.com or provided in conjunction with such TI products. TI's provision of these resources does not expand or otherwise alter TI's applicable warranties or warranty disclaimers for TI products. Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2020, Texas Instruments Incorporated