RM15WTRZB-4PA(72) - Hirose Electric

1

General-purpose Multi-Contact Circular Waterproof Connectors

RM-W Series

2006.1

■Overview

High performance waterproof circular connectors and cable

assemblies used in variety of applications requiring high

reliability, ease of assembly and small size.

■Features

1. Variety of types

Plugs : Available in 3 types - straight / long

back shell, straight / short back

shell, right angle back shell.

Receptacles : Waterproof types with front, back or

flange panel mounting.

All types with 2, 3, 4, 8, 10, 12, 15, 20, 31, 40, 55

contacts. Contacts in 2 plating types: gold or silver.

2. Dust and water protection

When fully mated, the connector meet requirements of

IP67 (48 hours at depth of 1.8 m)

(Single-body waterproof receptacles also meet

requirements of IP67.)

3. Cable exit in 360° directions

The right-angle plugs permit exiting of the cable over a

360-degree range in any direction.

■Applications

Base stations, factory automation equipment, robotic

equipment, exploration and construction equipment,

research instrumentation, variety of industrial and

measuring instruments. Any other applications requiring

high reliability waterproof circular connectors.

Ø23

40

41

Cable

360°

360° Cable exit

Plug _ Right angle

Plug _ straight

Ø21.5

Ø23

57

Ø21.5

48

Short backshell

Long backshell

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

2

2 m ø max.(2, 3, 4 pos.)

4 m ø max.(8, 10, 12 pos.)

1000 M ø min

No flashover or insulation breakdown.

No electrical discontinuity for 10µs max.

4 m ø max.(2, 3, 4 pos.)

8 m ø max.(8, 10, 12 pos.)

Insulation resistance: 100 M ø min.

Insulation resistance: 100 M ø min. (Dray state)

0When mated with corresponding connector.

1A DC

500V DC

1800V AC/one minute (2 pos.)

2000V AC/one minute (3 pos.)

1500V AC/one minute (4, 8 pos.)

1000V AC/one minute (10, 12 pos.)

Frequency: 10 to 55Hz, single amplitude of 0.75mm,for 3

hours in 3 axis.

Acceleration of 490m/s2, 11ms duration, sine half-wave

waveform, 3 cycles in each of the 3 axis.

2000 cycles

Temperature :

-55ç ➝Room temperature ➝+85ç ➝Room temperature

Time : 30 ➝10 to 15 ➝30 ➝10 to 15 (Minutes)

5 cycles

96 hours at temperature 0f 40ç and humidity 0f 90% to 95%.

Complete dust protection. No water penetration

when submerged for 48 hours at the depth of 1.8 meter.

1. Contact resistance

2.

Insulation resistance

3.

Withstanding voltage

4. Vibration

5. Shock

6. Durability

(insertion/withdrawal)

7. Temperature cycle

8. Humidity

9.

Water / dust protection

Rating

Voltage rating

Current rating

Operating temperature range (Note 1)

Storage temperature range (Note 2)

600V AC, 840V DC (2 pos.)

500V AC, 700V DC (3, 4, 8 pos.)

350V AC, 490V DC (10 pos.)

350V AC, 490V DC (12 pos.)

10A (2, 3, 4 pos.)

5A (8, 10, 12 pos.)

-25ç to +85ç

■Product Specifications (RM15WT size products)

■Materials

Characteristic Specification Conditions

Body

Insulator

Contacts

Gasket

Zinc alloy, brass, pliable PVC

Diallyl phthalate, PBT

Brass, phosphor bronze, or copper alloy

SIR (black or red), or NBR (gray)

Chrome plated or nickel plated

Color: Black

Silver plated or gold plated

Color: black or red (SIR), color: gray (NBR)

-------------------

UL94V-0

-------------------

Item Material Finish Remarks

Note 1: Includes temperature rise caused by the current flow.

Note 2: The term “storage” refers to products stored for long period of time prior to mounting and use. Operating temperature range and humidity range

Note 2: covers non-conducting condition of installed connectors in storage, shipment or during transportation.

Note: Do not mix different contact plating.

■Ordering Information

RM 15 W T P****- 2 P (****)

1 2 1 3 4 5 6 7

Series name : RM-W

Shell size

Lock type

T : Screw Lock

Connector type

P : Plug

R : Receptacle

1Number of Contacts

Contact type

P : Male contact

S : Female contact

Plating

(71) : Silver plated

(72) : Gold plated

5

62

3

4 7

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

3

■Plugs - straight, long back shell

■Applicable Strain reliefs

●External cable clamp + internal, self-tightening

●Internal, self tightening

109-1734-5-ππ

Part Number CL No.

Number of Contacts

Weight RoHS

RM15WTPZA-2P(ππ)

RM15WTPZA-3P( 72 )

RM15WTPZA-4P(ππ)

RM15WTPZA-8P(ππ)

RM15WTPZA-10P(ππ)

RM15WTPZA-12P(ππ)

2 43g

YES

109-1602-4- 72

109-1735-8-ππ

109-1736-0-ππ

109-1737-3-ππ

109-1738-6-ππ

3

4

8

10

12

45g

44g

43g

44g

M19∞1 M20∞0.75

Wrench opening dimension

of 18 mm

Ø15.2

45.3

Ø21.5

2

13

Part Number CL No.

Number of Contacts

Weight RoHS

RM15WTPZA-2S(ππ)

RM15WTPZA-3S(ππ)

RM15WTPZA-4S(ππ)

RM15WTPZA-8S(ππ)

RM15WTPZA-10S(ππ)

RM15WTPZA-12S(ππ)

109-1729-5-ππ 2 45g

YES

109-1601-1-ππ

109-1730-4-ππ

109-1731-7-ππ

109-1732-0-ππ

109-1733-2-ππ

3

4

8

10 45g

12

47g

45g

(shown one example)

Wrench opening dimension

of 21 mm

Ø23

M20∞0.75

17.5 Drive screw(2)

A

Wrench opening dimension

of 21 mm

Ø23

M20∞0.75

8

A

RM15WTPZA-10S(71)

JR16WCC-10(72)

JR16WCCA-10(72)

Part Number CL No. AWeight RoHS

JR16WCC-4(72)

JR16WCC-6(72)

JR16WCC-8(72)

114-2052-6-72 4 17.5g

114-2053-9-72

114-2054-1-72

6

8

17.5g

Part Number CL No. AWeight RoHS

JR16WCC-10(72)

JR16WCC-11(72)

JR16WCC-12(72)

114-2055-4-72 10 17.5g

YES114-2154-6-72

114-2056-7-72

11

12

17.5g

Part Number CL No. AWeight RoHS

JR16WCCA-4(72)

JR16WCCA-6(72)

Notes : 1. Cable jacket diameter:Use A ± 0.2mm

2. When using the self-tightening strain relief verify the cable pull force requirements.

JR16WCCA-8(72)

114-2076-4-72

114-2077-7-72

114-2078-0-72

4 16g

6 16g

8 16g

YES

Part Number CL No. AWeight RoHS

JR16WCCA-10(72)

JR16WCCA-11(72)

JR16WCCA-12(72)

114-2079-2-72

114-2155-9-72

114-2080-1-72

10 16g

11 16g

12 16g

YES

[Specification number] (**), -**

(71) : Silver plated contacts

(72) : Gold plated contacts

(shown one example)

YES

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

4

109-1616-9-ππ

Part Number CL No.

Number of Contacts

Weight RoHS

RM15WTPZ-2P(ππ)

RM15WTPZ-3P(ππ)

RM15WTPZ-4P(ππ)

RM15WTPZ-8P(ππ)

RM15WTPZ-10P(ππ)

RM15WTPZ-12P(ππ)

2 32g

YES

109-1622-1-ππ

109-1617-1-ππ

109-1618-4-ππ

109-1619-7-ππ

109-1620-6-ππ

3

4

8

10

12

34g

33g

32g

33g

M19∞1 M16∞0.75

Wrench opening dimension

of 18 mm

Ø15.2

36.3

Ø21.5

13

2

Part Number CL No.

Number of Contacts

Weight RoHS

RM15WTPZ-2S(ππ)

RM15WTPZ-3S(ππ)

RM15WTPZ-4S(ππ)

RM15WTPZ-8S(ππ)

RM15WTPZ-10S(ππ)

RM15WTPZ-12S(ππ)

109-1611-5-ππ

2 34g

YES

109-1621-9-ππ

109-1612-8-ππ

109-1613-0-ππ

109-1614-3-ππ

109-1615-6-ππ

3

4

8

10

12

36g

34g

17

M16∞0.75

Wrench opening dimension

of 17 mm

Ø20

A

Drive screw(2)

7.5

M16∞0.75

Wrench opening dimension

of 17 mm

Ø20

A

RM15WTPZ-10S

JR13WCC-10(72)

JR13WCCA-10(72)

Part Number CL No. AWeight RoHS

JR13WCC-4(72)

JR13WCC-5(72)

JR13WCC-6(72)

114-2045-0-72 4 17g

YES114-2046-3-72

114-2047-6-72

5 17g

6 17g

Part Number CL No. AWeight RoHS

JR13WCC-7(72)

JR13WCC-8(72)

JR13WCC-9(72)

JR13WCC-10(72)

114-2048-9-72 7 17g

YES

114-2049-1-72

114-2050-0-72

114-2051-3-72

8 17g

9 17g

10 17g

Part Number CL No. AWeight RoHS

JR13WCCA-4(72)

JR13WCCA-5(72)

Notes : 1. Cable jacket diameter: Use A ± 0.2mm

2. When using the self-tightening strain relief verify the cable pull force requirements.

JR13WCCA-6(72)

114-2069-9-72

114-2070-8-72

114-2071-0-72

4 12g

5 12g

6 12g

YES

Part Number CL No. AWeight RoHS

JR13WCCA-7(72)

JR13WCCA-8(72)

JR13WCCA-9(72)

JR13WCCA-10(72)

114-2072-3-72

114-2073-6-72

114-2074-9-72

114-2075-1-72

7 12g

8 12g

9 12g

10 12g

YES

■Plugs - Straight, short back shell

■Applicable Strain reliefs

●External cable clamp + internal, self-tightening

●Internal, self tightening

[Specification number] (**), -**

(71) : Silver plated contacts

(72) : Gold plated contacts

(shown one example)

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

5

Notes : 1 Gasket material: NBR, body plating: nickel

2 Recommended set screw tightening torque: 0.2 to 0.3 N•m.

HRS recommended tool: PB205/1.27(CL 150-0066-3)

109-0997-9-71

Part Number CL No.

Number of Contacts

Weight RoHS

RM15WTLP-12P(71)

12 62.3g YES

M19∞1

M16∞0.75

Wrench opening dimension

of 21.8 mm

Set screw(2)

Hexagonal hole

opposite side

1.27 mm

(1.27HEX)

Ø15.2

19.15

39.5

Ø23

Part Number CL No.

Number of Contacts

Weight RoHS

RM15WTLP-10S(71) 109-0999-4-71

10 63.1g YES

17

M16∞0.75

Wrench opening dimension

of 17 mm

Ø20

A

Drive screw(2)

7.5

M16∞0.75

Wrench opening dimension

of 17 mm

Ø20

A

RM15WTLP-10S

JR13WCC-10(72)

JR13WCCA-10(72)

Part Number CL No. AWeight RoHS

JR13WCC-4(72)

JR13WCC-5(72)

JR13WCC-6(72)

114-2045-0-72 4 17g

YES114-2046-3-72

114-2047-6-72

5 17g

6 17g

Part Number CL No. AWeight RoHS

JR13WCC-7(72)

JR13WCC-8(72)

JR13WCC-9(72)

JR13WCC-10(72)

114-2048-9-72 7 17g

YES

114-2049-1-72

114-2050-0-72

114-2051-3-72

817g

917g

10 17g

Part Number CL No. AWeight RoHS

JR13WCCA-4(72)

JR13WCCA-5(72)

Notes : 1 Cable jacket diameter: Use A ± 0.2mm

2 When using the self-tightening strain relief verify the cable pull force requirements.

JR13WCCA-6(72)

114-2069-9-72

114-2070-8-72

114-2071-0-72

4 12g

5 12g

6 12g

YES

Part Number CL No. AWeight RoHS

JR13WCCA-7(72)

JR13WCCA-8(72)

JR13WCCA-9(72)

JR13WCCA-10(72)

114-2072-3-72

114-2073-6-72

114-2074-9-72

114-2075-1-72

712g

812g

912g

10 12g

YES

■Plugs - right angle

■Applicable Strain reliefs

●External cable clamp + internal, self-tightening

●Internal, self tightening

(shown one example)

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

6

■Receptacles

● Front panel mount

● Rear panel mount

Notes : Recommended nut tightening torque: 3N•m

109-1631-2-ππ

109-1632-5-ππ

109-1633-8-ππ

109-1634-0-ππ

109-1635-3-ππ

109-1636-6-ππ

109-1637-9-ππ

CL No.

109-1638-1-ππ

109-1639-4-ππ

109-1640-3-ππ

109-1641-6-ππ

109-1642-9-ππ

Part Number CL No.

Number of Contacts

Weight RoHS

A

13g

YES

21

15g22.1

14g21

13g20.65

14g20.65

15g

YES

Weight RoHS

17g

15g

RM15WTRZ-2P(ππ)

RM15WTRZ-3P(ππ)

RM15WTRZ-4P(ππ)

RM15WTRZ-8P(ππ)

RM15WTRZ-10P(ππ)

RM15WTRZ-12P(ππ)

RM15WTRZ-2S(ππ)

Part Number

RM15WTRZ-3S(ππ)

RM15WTRZ-4S(ππ)

RM15WTRZ-8S(ππ)

RM15WTRZ-10S(ππ)

RM15WTRZ-12S(ππ)

2

3

4

8

10

12

2 21.75

Number of Contacts

A

3 22.1

4 21.75

8 21.6

10 21.6

12 21.6

21

Wrench opening

dimension of 18 mm

A

96

2

M19∞1

Ø22

13

A

2

6.5

M19∞1

24(HEX)

M21∞1

Ø27

RM15WTRZ-10S(71)

RM15WTRZA-10S(71)

109-1651-0-ππ

109-1652-2-ππ

109-1653-5-ππ

109-1654-8-ππ

109-1655-0-ππ

109-1656-3-ππ

109-1657-6-ππ

CL No.

109-1658-9-ππ

109-1659-1-ππ

109-1660-0-ππ

109-1661-3-ππ

109-1662-6-ππ

Part Number CL No.

Number of Contacts

Weight RoHS

A

22g

YES

21

24g22.1

23g21

22g20.65

23g20.65

24g

YES

Weight RoHS

26g

24g

RM15WTRZA-2P(ππ)

RM15WTRZA-3P(ππ)

RM15WTRZA-4P(ππ)

RM15WTRZA-8P(ππ)

RM15WTRZA-10

P(ππ)

RM15WTRZA-12

P(ππ)

RM15WTRZA-2S(ππ)

Part Number

RM15WTRZA-3S(ππ)

RM15WTRZA-4S(ππ)

RM15WTRZA-8S(ππ)

RM15WTRZA-10

S(ππ)

RM15WTRZA-12

S(ππ)

2

3

4

8

10

12

2 21.75

Number of Contacts

A

3 22.1

4 21.75

8 21.6

10 21.6

12 21.6

[Specification number] (**), -**

(71) : Silver plated contacts

(72) : Gold plated contacts

[Specification number] (**), -**

(71) : Silver plated contacts

(72) : Gold plated contacts

(shown one example)

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

8

BPlug -- Disassembly / Assembly

5.

4.

3.

2.

1.

Disassembly

1Fix the plug in the assembly fixture (RM15TP-T01 (CL150-0098-0)), then remove the insulator body (P) and the back shell.

Right-angle plugs have set screws in the tightening ring at 2 locations. Loosen the set screws before removing the back shell.

2Remove the 2 screws of the strain relief clamp, and then remove the clamp from the tightening collar.

Part Name Number of Contacts

3

2,4,8,10,12

3

2,4,8,10,12

10,12

A

6mm

3mm

6mm

3mm

B

21mm

12mm

25mm

Cable jacket

Cable

Wires

Conductors

B

A

3 min

Strain relief clamp

Back shell

Coupling

Tightening collar

Washer

Bushing

Insulator body (P)

Contacts

Clamp

Screw

Cable

Set screw(2)

Back shell

Tightening ring

Wiring

1Assure that the cable outer diameter will fit the strain relief clamp, and is prepared as recommended in Table 1.

It is recommended that the exposed conductors be pre-soldered, to assure easier insertion in the soldering cup.

2Pass the parts over the cable in the order of: tightening collar, washer, bushing, back shell, and coupling. Refer to the drawings

(above) for assembly orientation of all components.

3Solder the wires to the contacts of the insulator body (P).

Use of heat-shrink tubing or another insulating media between the soldered contacts is suggested.

Connector Assembly

Straight Plugs

1Place the completely wired insulator body (P) in the assembly fixture secured in a vise. Insert in the coupling, then back shell. The

back shell should be tightened to a torque of 3 N•m.

Right-angle Plugs

1Place the completely wired insulator body (P) in an assembly fixture secured by a vise. Insert in the coupling, then back shell (with

tightening ring). When attaching the back shell, orient the cable in the desired direction and fasten the tightening ring to the

insulator body (P) with a torque of 3 N•m. After this, tighten and fix the 2 sets crews with a torque of 0.2 to 0.3 N•m.

Additional assembly recommendations:

In applications where continuous extremely high vibrations may be encountered it is recommended that a thread locking

compound be applied to male threads prior to assembly (Loctite 271 ˛ manufactured by Henkel Japan K.K. or equivalent)

Waterproof verification - plug assembly

Apply air pressure of 17.6 kPa for 30 seconds from the mating side of the plug assembly. There shall not be any air leakage from

inside the connector when submerged in the water tank.

Precautions

1Follow the correct assembly sequence, cable preparation and tightening torques.

2Assure that the applicable cable outer surfaces are free of scratches, oil, grease or any other contamination.

3Do not use excessive forces or improper tools when assembling or mounting the connectors.

RM15WTPZA-ππ

RM15WTPZ-ππ

RM15WTLP-ππ

Table 1

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

9

BReceptacle - recommended panel cut-outs

BContact Position Arrangement and Specifications

BPrecautions

1. Switch off the power of the circuit before disconnecting or plugging- in the connectors.

2. Use a connectors with socket contacts at the power side of the circuit.

3. Make sure that the coupling is in completely cocked position.

4. Use correct plug / receptacle to assure dust and water protection.

Ø17

+0.1

0

Ø7.6+0.1

0

Front mounting, rear nut

Ø21

+0.1

0

Ø19.65+0.05

0

Rear mounting, front nut

4-M3∞0.5

Ø24+0.1

0

Ø19.2+0.1

0

20.6±0.05

1.4±0.05

Square flange, screw mounting

Contact

configuration

Shell size : 15

Number of contacts

Withstanding voltage

Current rating

Insulation resistance

Contact resistance

Solder pot inner diameter

2

1800V AC / 1 minute

10A

1000Mø min.

2mø max.

1.7mm

3

2000V AC / 1 minute

10A

1000Mø min.

2mø max.

2.8mm

4

1500V AC / 1 minute

10A

1000Mø min.

2mø max.

1.7mm

8

1500V AC / 1 minute

5A

1000Mø min.

4mø max.

1.1mm

10

1000V AC / 1 minute

5A

1000Mø min.

4mø max.

1.1mm

12

1000V AC / 1 minute

5A

1000Mø min.

4mø max.

1.1mm

Panel thickness: 0.5 to 2 mm

For RM15WTRZ receptacles

Panel thickness: 0.5 to 2.5 mm

For RM15WTRZA receptacles

Panel thickness: 2.5 to 4 mm

For RM15WTRZB receptacles

Notes : 1. When attaching the receptacle to the panel, be certain to check that the gasket is in place in the groove. Do not pinch the gasket.

Notes : 2. The view of the above diagrams is from the receptacle mating side.

Notes : 3. The ▼symbol in the above diagrams indicates the coupling guide position of the receptacles.

Notes : 1. The contact configuration as viewed from the wiring side.

Notes : 2. The ▼symbol in the above diagrams indicates the coupling guide position of the receptacles.

Notes : 3. Withstanding voltages indicate test voltage values.

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

10

4 m ø max.

1000 M ø min

No flashover or insulation breakdown.

No electrical discontinuity for 10µs max.

8 m ø max.

Insulation resistance: 100 M ø min.

Insulation resistance: 100 M ø min. (Dray state)

0When mated with corresponding connector.

1A DC

500V DC

1800V AC/one minute (4 pos.)

1500V AC/one minute (15, 31, 55 pos.)

1000V AC/one minute (20 pos.)

Frequency: 10 to 55Hz, single amplitude of 0.75mm,for 3

hours in 3 axis.

Acceleration of 490m/s2, 11ms duration, sine half-wave

waveform, 3 cycles in each of the 3 axis.

2000 cycles

Temperature :

-55ç ➝Room temperature ➝+85ç ➝Room temperature

Time : 30 ➝10 to 15 ➝30 ➝10 to 15 (Minutes)

5 cycles

96 hours at temperature 0f 40ç and humidity 0f 90% to 95%.

Complete dust protection. No water penetration

when submerged for 48 hours at the depth of 1.8 meter.

1. Contact resistance

2.

Insulation resistance

3.

Withstanding voltage

4. Vibration

5. Shock

6. Durability

(insertion/withdrawal)

7. Temperature cycle

8. Humidity

9.

Water / dust protection

Rating

Voltage rating

Current rating

Operating temperature range (Note 1)

Storage temperature range (Note 2)

600V AC, 840V DC (40 pos.)

500V AC, 700V DC (15, 31, 55 pos.)

350V AC, 490V DC (20 pos.)

5A

-25ç to +85ç

■Product Specifications (RM21WT to RM31WT size products)

■Materials

Characteristic Specification Conditions

Body

Insulator

Contacts

Gasket

Brass

Diallyl phthalate

Brass, copper alloy

Chloroprene rubber or SIR

Chrome plated or nickel plated

Color: Black

Silver plated or gold plated

Color: black

-------------------

UL94V-0

-------------------

Item Material Finish Remarks

Note 1: Includes temperature rise caused by the current flow.

Note 2: The term “storage” refers to products stored for long period of time prior to mounting and use. Operating temperature range and humidity range

Note 2: covers non-conducting condition of installed connectors in storage, shipment or during transportation.

Note: Do not mix different contact plating.

■Ordering Information

RM 21 W T P****- 2 P (****)

1 2 1 3 4 5 6 7

Series name : RM-W

Shell size

Lock type

T : Screw Lock

Connector type

P : Plug

R : Receptacle

1Number of Contacts

Contact type

P : Male contact

S : Female contact

Plating

(71) : Silver plated

(72) : Gold plated

5

62

3

4 7

RM 21 W T P - CP (10) (****)

8 9

CP: Strain relief

8() with : External cable clamp

() without : Internal cable clamp

4~18 : Cable size

9

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

11

109-1860-0-71

109-1852-1-71

109-1855-0-71

■Plugs - straight, long back shell

Part Number CL No.

Number of Contacts

ØA

RM21WTPS-15S(71)

RM24WTPB-31S(71)

RM24WTPB-31P(71)

15

31

21

24.3

ØB

32

36

C

49

54

D

23

26

E

TM25∞2

TM29∞2

F

M20∞0.75

M24∞0.75

Weight

Remarks

RoHS

104.5

144.6

140.0

Silver plated

only YES

Wrench opening dimension D

10 1

15 2

14

3

11

9

8

12

4

756

13

Y

Z

C

F

ØA

ØB

E

(shown one example)

ØB

ØA

E

Wrench opening dimension D C

(shown one example)

Set screw

ØA

D

C

ØB

E

(shown one example)

RM21WTPS-15S(71)

Notes : 1. Cable jacket diameter:Use A ± 0.2mm. Notes : 2. Recommended set screw tightening torque : 0.2 to 0.3 N•m.

Notes : 3. When using the self-tightening strain relief verify the cable pull force requirements.

Notes : 1. Cable jacket diameter:Use A ± 0.2mm. Notes : 2. Recommended set screw tightening torque : 0.3 to 0.4 N•m.

HRS recommended tool : PB205/1.27(CL 150-0066-3)

■Applicable Strain reliefs

●External cable clamp + internal, self-tightening

●Internal, self tightening

RM24WTP-CP14(71)

RM21WTP-CP(8)(71)

114-2052-6-72

114-2053-9-72

114-2054-1-72

114-2055-4-72

114-2154-6-72

114-2056-7-72

109-1851-9-71

Part Number CL No. ØA

JR16WCC-4(72)

JR16WCC-6(72)

JR16WCC-8(72)

JR16WCC-10(72)

JR16WCC-11(72)

JR16WCC-12(72)

RM24WTP-CP14(71)

04

06

08

10

11

12

14

ØB

23

29

C

17.5

D

21

26

E

M20∞0.75

M24∞0.75

Weight

17.5g

Remarks

RoHS

For RM21WT YES

For RM24WT

109-1405-3-71

109-1406-6-71

109-1407-9-71

109-1493-0-71

109-1494-3-71

109-1495-6-71

109-1496-9-71

Part Number CL No. ØA

RM21WTP-CP(8)(71)

RM21WTP-CP(10)(71)

RM21WTP-CP(12)(71)

RM24WTP-CP(10)(71)

RM24WTP-CP(12)(71)

RM24WTP-CP(14)(71)

RM24WTP-CP(16)(71)

08

10

12

10

12

14

16

ØB

23

27

C

38

38.5

D

7.5

8

E

M20∞0.75

M24∞0.75

Weight Remarks

RoHS

22.5

22.0

21.5

28.5

28.0

26.5

For RM21WT

YES

For RM24WT

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

12

109-1405-3-71

109-1406-6-71

109-1407-9-71

109-1493-0-71

109-1494-3-71

109-1495-6-71

109-1496-9-71

109-1575-3-71

109-1576-6-71

109-1579-4-71

109-1577-9-71

109-1578-1-71

Part Number CL No. ØA

RM21WTP-CP(8)(71)

RM21WTP-CP(10)(71)

RM21WTP-CP(12)(71)

RM24WTP-CP(10)(71)

RM24WTP-CP(12)(71)

RM24WTP-CP(14)(71)

RM24WTP-CP(16)(71)

RM31WTP-CP(10)(71)

RM31WTP-CP(12)(71)

RM31WTP-CP(14)(71)

RM31WTP-CP(16)(71)

RM31WTP-CP(18)(71)

08

10

12

10

12

14

16

10

12

14

16

18

ØB

23

27

31

C

38

38.5

42

D

7.5

8

12

E

M20∞0.75

M24∞0.75

M28∞0.75

Weight RoHS

22.5

22

21.5

28.5

46

45

43.5

42

YES

■Plugs - Straight, short back shell

D

C

ØA

ØB

E

14

13

9

8

765

4

3

2

1

10

15 11

12

Y

Z

Set screw

(shown one example)

ØB

ØA

E

Wrench opening dimension D C

(shown one example)

Set screw

ØA

D

C

ØB

E

(shown one example)

RM21WTP-15S(71)

Notes : 1. Cable jacket diameter:Use A ± 0.2mm. Notes : 2. Recommended set screw tightening torque : 0.2 to 0.3 N•m.

Notes : 3. When using the self-tightening strain relief verify the cable pull force requirements.

■Applicable Strain reliefs

●External cable clamp + internal, self-tightening

●Internal, self tightening

RM24WTP-CP14(71)

RM21WTP-CP(8)(71)

109-1401-2-71

109-1402-5-71

109-1403-8-71

109-1404-0-71

109-1491-5-71

109-1492-8-71

109-1571-2-71

109-1572-5-71

109-1573-8-71

109-1574-0-71

Part Number CL No.

Number of Contacts

ØA

RM21WTP-15S(71)

RM21WTP-20S(71)

RM21WTP-15P(71)

RM21WTP-20P(71)

RM24WTP-31S(71)

RM24WTP-31P(71)

RM31WTP-40S(71)

RM31WTP-55S(71)

RM31WTP-40P(71)

RM31WTP-55P(71)

15

20

15

20

31

40

55

40

55

21

24.3

30.8

ØB

32

36

42

C

37.5

44

52

E

TM25∞2

TM29∞2

TM35∞2

F

M20∞0.75

M24∞0.75

M28∞0.75

Weight Remarks

RoHS

88.5

85

128

123

152

157

152

150

Silver plated

only YES

109-1478-7-71

109-1477-4-71

109-1851-9-71

Part Number CL No. ØA

RM21WTP-CP10(71)

RM21WTP-CP12(71)

RM24WTP-CP14(71)

10

12

14

ØB

25

29

C

17

17.5

D

21

26

ERoHS

M20∞0.75

M24∞0.75

YES

Notes : 1. Cable jacket diameter:Use A ± 0.2mm. Notes : 2. Recommended set screw tightening torque : 0.3 to 0.4 N•m.

HRS recommended tool : PB205/1.27(CL 150-0066-3)

Notes : Recommended set screw tightening torque : 0.2 to 0.3 N•m.

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

13

Notes : Recommended nut tightening torque : 3 N•m

■Receptacles

ØA

CD

13

14

15

12

1

11

10

11 9

12

8

15

2

3

14

7

465

13

Y

Z

10 1

2

3

9

8

4

7

5

6

Y

Z

EB

F

(shown one example)

20.6±2

6

TM25∞2

4-Ø3.6

7

8

9

3

7

8

9

10

5

1

10

4

6

2

13

12

11

15

16

17

19

18

14

20

3

5

1

4

6

2

13

12

11

15

16

17

19

18

14

20

32

24

Ø23.7

32

24

(shown one example)

RM21WTR-15P(71)

RM21WTRK-20P(71)

● Waterproof (single body)

Notes : 1. Screw size : M3

2. Recommended nut tightening torque : 0.3 to 0.35 N•m

3. Use a 1.9 to 2.0 mm dia.thick O-ring for the waterproof gasket that is used in the connector mounting portion.

109-1466-8-71

Part Number CL No.

Number of Contacts

Remarks RoHS

RM21WTRK-20P(71) 20 Gold plated only YES

109-1445-8-71

109-1447-3-71

109-1446-0-71

109-1448-6-71

109-1483-7-71

109-1484-0-71

109-1525-5-71

109-1527-0-71

109-1526-8-71

109-1528-3-71

Part Number CL No.

Number of Contacts

ØA B C D E

RM21WTR-15P(71)

RM21WTR-15S(71)

RM21WTR-20P(71)

RM21WTR-20S(71)

RM24WTR-31P(71)

RM24WTR-31S(71)

RM31WTR-40P(71)

RM31WTR-40S(71)

RM31WTR-55P(71)

RM31WTR-55S(71)

15

20

31

40

55

31

35

41

21

6.5

2

2.5

23.5

28

34

E

TM25∞2

TM29∞2

TM35∞2

Weight Remarks

RoHS

28

31.5

41.5

42

50

52

53.5

54

Silver plated

only YES

● Front panel mount

The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.

All non-RoHS products have been discontinued, or will be discontinued soon. Please check the products status on the Hirose website RoHS search at www.hirose-connectors.com, or contact your Hirose sales representative.

14

ØA

B

RC

4–M3∞0.5 1.4±0.05

Ø24 +0.1

0

Ø28±0.1

24±0.05

Notes : Tolelance is +0.1/0.

BReceptacle - recommended panel cut-out