- 222 -
SF1001G THRU SF1008G
10.0 AMPS. Glass Passivated Super Fast Rectifiers
Voltage Range
50 to 600 Volts
Current
10.0 Amperes
Features
Low forward voltage drop
High current capability
High reliability
High surge current capability
Mechanical Data
Case: Molded plastic
Epoxy: UL 94V-O rate flame retardant
Terminals: Leads solderable per MIL-STD-
202, Method 208 guaranteed
Polarity: As marked
High temperature soldering guaranteed:
260
oC/10 seconds .16”,(4.06mm) from
case.
Weight: 2.24 grams
TO-220
Dimensions in inches and (millimeters)
Maximum Ratings and Electrical Characteristics
Rating at 25℃ambient temperature unless otherwise specified.
Single phase, half wave, 60 Hz, resistive or inductive load.
For capacitive load, derate current by 20%
Type Number Symbol SF
1001G SF
1002G SF
1003G SF
1004G SF
1005G SF
1006G SF
1007G SF
1008G Units
Maximum Recurrent Peak Reverse
Voltage VRRM 50 100 150 200 300 400 500 600 V
Maximum RMS Voltage VRMS 35 70 105 140 210 280 350 480 V
Maximum DC Blocking Voltage VDC 50 100 150 200 300 400 500 600 V
Maximum Average Forward Rectified
Current .375 (9.5mm) Lead Length
@TC = 100℃ I(AV) 10.0 A
Peak Forward Surge Current, 8.3 ms
Single Half Sine-wave Superimposed on
Rated Load (JEDEC method ) IFSM 125 A
Maximum Instantaneous Forward Voltage
@ 5.0A VF 0.975 1.3 1.7 V
Maximum DC Reverse Current
@ TA=25℃at Rated DC Blocking Voltage
@ TA=100℃
IR 10.0
400 uA
uA
Maximum Reverse Recovery Time
(Note 1) Trr 35 nS
Typical Junction Capacitance (Note 2) Cj 70 50 pF
Typical Thermal Resistance (Note 3) R
θ
JC 3.5 ℃/W
Operating Temperature Range TJ -65 to +150 ℃
Storage Temperature Range TSTG -65 to +150 ℃
Notes: 1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, IRR=0.25A
2. Measured at 1 MHz and Applied Reverse Voltage of 4.0 V D.C.
3. Mounted on Heatsink Size of 2 in x 3 in x 0.25 in Al-plate..
PIN 1
PIN 3
Positive CT
PIN 2
CASE
- 223 -
FIG.3- TYPICAL REVERSE CHARACTERISTICS
INSTANTANEOUS REVERSE CURRENT.( A)
020 40 60 80 100 120 140
1000
0.1
1.0
10
100
PERCENT OF RATED PEAK REVERSE VOLTAGE. (%)
TC=25 C
0
TC=100 C
0
FIG.1- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM
50W
NONINDUCTIVE
1W
NON
INDUCTIVE
OSCILLOSCOPE
(NOTE 1)
PULSE
GENERATOR
(NOTE 2)
DUT
(+)
50Vdc
(approx)
(-)
NOTES: 1. Rise Time=7ns max. Input Impedance=
1 megohm 22pf
2. Rise Time=10ns max. Sourse Impedance=
50 ohms
(-)
(+)
10W
NONINDUCTIVE
-1.0A
-0.25A
0
+0.5A
trr
1cm SET TIME BASE FOR
5/ 10ns/ cm
RATINGS AND CHARACTERISTIC CURVES (SF1001G THRU SF1008G)
FIG.2- MAXIMUM FORWARD CURRENT DERATING
CURVE
AVERAGE FORWARD CURRENT. (A)
050 100 150
0
4
8
12
16
20
CASE TEMPERATURE. ( C)
o
FIG.4- MAXIMUM NON-REPETITIVE FORWARD SURGE
CURRENT PER LEG
PEAK FORWARD SURGE CURRENT. (A)
12 5 10 20 10050
30
120
90
60
NUMBER OF CYCLES AT 60Hz
TC=125 C
0
8.3ms Single Half Sine Wave
JEDEC Method
FIG.5- TYPICAL JUNCTION CAPACITANCE PER LEG
CAPACITANCE.(pF)
152 10 20 50 100 200 500
50
60
70
80
90
100
REVERSE VOLTAGE. (V)
Tj=25 C
0
SF1001G~SF1004G
SF1005G~SF1008G
FIG.6- TYPICAL FORWARD CHARACTERISTICS
PER LEG
INSTANTANEOUS FORWARD CURRENT. (A)
.4 .6 .8 1.0 1.2 1.4 1.6 1.8
.01
0.1
.03
1.0
0.3
10
3.0
30
100
FORWARD VOLTAGE. (V)
Tj=25 C
Pulse Width=300 s
1% Duty Cycle
o
SF1001G~SF1004G
SF1005G~SF1006G
SF1007G~SF1008G
