OPA129 OPA OPA 129 129 SBOS026A - JANUARY 1994 - REVISED APRIL 2007 Ultra-Low Bias Current Difet(R) OPERATIONAL AMPLIFIER FEATURES APPLICATIONS ULTRA-LOW BIAS CURRENT: 100fA max LOW OFFSET: 2mV max LOW DRIFT: 10V/C max HIGH OPEN-LOOP GAIN: 94dB min LOW NOISE: 15nV/Hz at 10kHz PLASTIC DIP AND SO PACKAGES PHOTODETECTOR PREAMPS CHROMATOGRAPHY ELECTROMETER AMPLIFIERS MASS SPECTROMETERS pH PROBE AMPLIFIERS ION GAGE MEASUREMENT Substrate DESCRIPTION 8 The OPA129 is an ultra-low bias current monolithic operational amplifier offered in an 8-pin PDIP and SO-8 package. Using advanced geometry dielectrically-isolated FET (Difet(R)) inputs, this monolithic amplifier achieves a high performance level. Difet fabrication eliminates isolation-junction leakage current--the main contributor to input bias current with conventional monolithic FETs. This reduces input bias current by a factor of 10 to 100. Very low input bias current can be achieved without resorting to small-geometry FETs or CMOS designs which can suffer from much larger offset voltage, voltage noise, drift, and poor power-supply rejection. The OPA129 special pinout eliminates leakage current that occurs with other op amps. Pins 1 and 4 have no internal connection, allowing circuit board guard traces-- even with the surface-mount package version. OPA129 is available in 8-pin DIP and SO packages, specified for operation from -40C to +85C. 7 V+ -In 2 3 +In Noise-Free Cascode 6 Output 30k 30k 5 V- Simplified Circuit Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Difet is a registered trademark of Texas Instruments. All other trademarks are the property of their respective owners. Copyright (c) 1994-2007, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. www.ti.com SPECIFICATIONS ELECTRICAL At VS = 15V and TA = +25C, unless otherwise noted. Pin 8 connected to ground. OPA129PB, UB PARAMETER CONDITION MIN TYP OPA129P, U MAX MIN 30 100 Doubles every 10C TYP MAX UNITS * * 250 fA INPUT BIAS CURRENT(1) vs Temperature VCM = 0V INPUT OFFSET CURRENT VCM = 0V 30 VCM = 0V VS = 5V to 18V 0.5 3 3 f = 10Hz f = 100Hz f = 1kHz f = 10kHz fB = 0.1Hz to 10Hz f = 10kHz 85 28 17 15 4 0.1 * * * * * * nV/Hz nV/Hz nV/Hz nV/Hz VPP fA/Hz 1013 || 1 1015 || 2 * * || pF || pF OFFSET VOLTAGE Input Offset Voltage vs Temperature Supply Rejection NOISE Voltage Current INPUT IMPEDANCE Differential Common-Mode VOLTAGE RANGE Common-Mode Input Range Common-Mode Rejection OPEN-LOOP GAIN, DC Open-Loop Voltage Gain FREQUENCY RESPONSE Unity Gain, Small Signal Full Power Response Slew Rate Settling Time: 0.1% 0.01% Overload Recovery, 50% Overdrive(2) RATED OUTPUT Voltage Output Current Output Load Capacitance Stability Short-Circuit Current POWER SUPPLY Rated Voltage Voltage Range, Derated Performance Current, Quiescent TEMPERATURE Specification Operating Storage Thermal Resistance DIP-8 SO-8 * 2 10 100 1 5 * fA 5 * mV V/C V/V VIN = 10V 10 80 12 118 * * * * V dB RL 2k 94 120 * * dB 1 1 47 2.5 * * * * MHz kHz V/s * * * s s s * * * * * V mA pF mA * * V V mA * * * C C C 20Vp-p, RL = 2k VO = 10V, RL = 2k G = -1, RL = 2k, 10V Step 5 10 5 G = -1 RL = 2k VO = 12V Gain = +1 12 6 5 IO = 0mA Ambient Temperature Ambient Temperature 13 10 1000 35 15 1.2 -40 -40 -40 * * 55 * 18 1.8 * +85 +125 +125 * * * * JA, Junction-to-Ambient 90 100 * * C/W C/W NOTES: (1) High-speed automated test. (2) Overload recovery is defined as the time required for the output to return from saturation to linear operation following the removal of a 50% input overdrive. 2 OPA129 www.ti.com SBOS026A PACKAGE INFORMATION(1) ABSOLUTE MAXIMUM RATINGS Power Supply Voltage ...................................................................... 18V Differential Input Voltage ............................................................ V- to V+ Input Voltage Range .................................................................... V- to V+ Storage Temperature Range ......................................... -40C to +125C Operating Temperature Range ...................................... -40C to +125C Output Short Circuit Duration(1) .................................................................. Continuous Junction Temperature (TJ) ............................................................ +150C PRODUCT PACKAGE-LEAD PACKAGE DESIGNATOR OPA129P OPA129PB OPA129U OPA129UB DIP-8 DIP-8 SO-8 SO-8 P P D D NOTE: (1) For the most current package and ordering information, see the Package Option Addendum at the end of this data sheet, or see the TI website at www.ti.com. NOTE: (1) Short circuit may be to power supply common at +25C ambient. CONNECTION DIAGRAM ELECTROSTATIC DISCHARGE SENSITIVITY Top View Any integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage. DIP/SO NC 1 -In 2 8 Substrate 7 V+ OPA +In 3 6 Output NC 4 5 V- NC: No internal connection. ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more susceptible to damage because very small parametric changes could cause the device not to meet published specifications. TYPICAL PERFORMANCE CURVES At TA = +25C, +15VDC, unless otherwise noted. OPEN-LOOP FREQUENCY RESPONSE POWER SUPPLY REJECTION vs FREQUENCY 140 45 Gain 100 80 Phase Margin 90 60 40 90 135 20 0 Pulse Shift (degrees) Voltage Gain (dB) 120 Power Supply Rejection (dB) 140 180 1 10 100 1k 10k 100k 1M 10M Frequency (Hz) 100 80 +PSRR 60 -PSRR 40 20 0 1 10 100 1k 10k 100k 1M 10M Frequency (Hz) OPA129 SBOS026A 120 www.ti.com 3 TYPICAL PERFORMANCE CURVES (Cont.) At TA = +25C, +15VDC, unless otherwise noted. COMMON-MODE REJECTION vs INPUT COMMON-MODE VOLTAGE COMMON-MODE REJECTION vs FREQUENCY 140 Common-Mode Rejection (dB) Common-Mode Rejection (dB) 120 110 100 90 80 120 100 80 60 40 20 0 70 15 10 5 0 10 5 1 15 10k 100k 1M BIAS AND OFFSET CURRENT vs INPUT COMMON-MODE VOLTAGE 10M 10 Normalized Bias and Offset Current Bias and Offset Current (fA) 1k BIAS AND OFFSET CURRENT vs TEMPERATURE 10pA 1pA IB and IOS 100 10 1 1 0.1 0.01 -50 -25 0 25 50 75 100 125 -15 Ambient Temperature (C) -10 -5 5 0 10 15 Common-Mode Voltage (V) FULL-POWER OUTPUT vs FREQUENCY INPUT VOLTAGE NOISE SPECTRAL DENSITY 30 Output Voltage (VPP) 1k Voltage Density (nV/Hz) 100 Frequency (Hz) 100pA 100 20 10 0 10 1 10 100 1k 10k 100k 1k 10k 100k 1M Frequency (Hz) Frequency (Hz) 4 10 Common-Mode Voltage (V) OPA129 www.ti.com SBOS026A TYPICAL PERFORMANCE CURVES (Cont.) At TA = +25C, +15VDC, unless otherwise noted. 3 3 2 2 1 Gain Bandwidth (MHz) 4 Slew Rate (V/s) Gain Bandwidth (MHz) 4 1 0 -50 -25 0 25 50 75 100 6 2 4 +Slew -Slew 1 0 0 125 5 10 Ambient Temperature (C) 15 20 Supply Voltage (VCC) SUPPLY CURRENT vs TEMPERATURE OPEN-LOOP GAIN, PSR AND CMR vs TEMPERATURE 2.0 130 PSR, CMR, Voltage Gain (dB) Supply Current (mA) 2 GBW 0 0 -75 3 Slew Rate (v/s) GAIN BANDWIDTH AND SLEW RATE vs SUPPLY VOLTAGE GAIN BANDWIDTH AND SLEW RATE vs TEMPERATURE 1.5 1.0 0.5 0 120 A OL CMR 110 100 PSR 90 -75 -50 -25 0 25 50 75 100 125 -75 -50 Ambient Temperature (C) -25 0 25 50 75 100 125 Ambient Temperature (C) SMALL SIGNAL TRANSIENT RESPONSE LARGE SIGNAL TRANSIENT RESPONSE 10 Output Voltage (mV) Output Voltage (V) 80 0 -10 5V 0 5s 25 0 -40 0 50 1s 20mV -80 2 4 6 8 10 Time (s) Time (s) OPA129 SBOS026A 40 www.ti.com 5 TYPICAL PERFORMANCE CURVES (CONT) TA = +25C, +15VDC, unless otherwise noted. COMMON-MODE INPUT RANGE vs SUPPLY VOLTAGE BIAS CURRENT vs ADDITIONAL POWER DISSIPATION 100pA 10pA Bias Current (fA) Common-Mode Voltage (+V) 15 10 5 100 10 0 1 0 5 10 15 20 0 APPLICATIONS INFORMATION NON-STANDARD PINOUT The OPA129 uses a non-standard pinout to achieve lowest possible input bias current. The negative power supply is connected to pin 5--see Figure 1. This is done to reduce the leakage current from the V- supply (pin 4 on conventional op amps) to the op amp input terminals. With this new pinout, sensitive inputs are separated from both power supply pins. RF V+ RIN VIN 2 3 7 OPA129 6 VOUT 5 V+ V- 470k 220 50 100 150 200 250 300 350 Additional Power Dissipation (mW) Supply Voltage (VCC) 470k 0.1F V- FIGURE 1. Offset Adjust Circuit. OFFSET VOLTAGE TRIM The OPA129 has no conventional offset trim connections. Pin 1, next to the critical inverting input, has no internal connection. This eliminates a source of leakage current and allows guarding of the input terminals. Pin 1 and pin 4, next to the two input pins, have no internal connection. This allows an optimized circuit board layout with guarding--see the Circuit Board Layout section. 6 1pA Due to its laser-trimmed input stage, most applications do not require external offset voltage trimming. If trimming is required, the circuit shown in Figure 1 can be used. Power supply voltages are divided down, filtered and applied to the non-inverting input. The circuit shown is sensitive to variation in the supply voltages. Regulation can be added, if needed. GUARDING AND SHIELDING Ultra-low input bias current op amps require precautions to achieve best performance. Leakage current on the surface of circuit board can exceed the input bias current of the amplifier. For example, a circuit board resistance of 1012 from a power supply pin to an input pin produces a current of 15pA--more than 100 times the input bias current of the op amp. To minimize surface leakage, a guard trace should completely surround the input terminals and other circuitry connecting to the inputs of the op amp. The DIP package should have a guard trace on both sides of the circuit board. The guard ring should be driven by a circuit node equal in potential to the op amp inputs--see Figure 2. The substrate, pin 8, should also be connected to the circuit board guard to assure that the amplifier is fully surrounded by the guard potential. This minimizes leakage current and noise pick-up. Careful shielding is required to reduce noise pickup. Shielding near feedback components may also help reduce noise pick-up. Triboelectric effects (friction-generated charge) can be a troublesome source of errors. Vibration of the circuit board, input connectors and input cables can cause noise and drift. Make the assembly as rigid as possible. Attach cables to avoid motion and vibration. Special low noise or low leakage cables may help reduce noise and leakage current. Keep all input connections as short possible. Surface-mount components may reduce circuit board size and allow a more rigid assembly. OPA129 www.ti.com SBOS026A CIRCUIT BOARD LAYOUT The OPA129 uses a new pinout for ultra low input bias current. Pin 1 and pin 4 have no internal connection. This allows ample circuit board space for a guard ring surrounding the op amp input pins--even with the tiny SO-8 surfacemount package. Figure 3 shows suggested circuit board layouts. The guard ring should be connected to pin 8 (substrate) as shown. It should be driven by a circuit node equal in potential to the input terminals of the op amp--see Figure 2 for common circuit configurations. TESTING Accurately testing the OPA129 is extremely difficult due to its high performance. Ordinary test equipment may not be able to resolve the amplifier's extremely low bias current. Inaccurate bias current measurements can be due to: 1. Test socket leakage. 2. Unclean package. 3. Humidity or dew point condensations. 4. Circuit contamination from fingerprints or anti-static treatment chemicals. 5. Test ambient temperature. 6. Load power dissipation. 7. Mechanical stress. 8. Electrostatic and electromagnetic interference. (A) Non-Inverting RF 2 6 Out 2 Current Input 3 7 6 OPA129 Output 5 8 VO = -IIN * RF VO = -10V/nA V- FIGURE 4. Current-to-Voltage Converter. 500 9.5k V+ Guard 8 2 7 6 OPA129 3 1VDC Output 5 V- pH Probe RS 500M 50mV Out FIGURE 5. High Impedance (1015) Amplifier. 1011 RF 8 3 V+ Out 8 2 In In 18k CF 10pF 6 3 2k V+ IIN (B) Buffer 8 2 1000M (C) Inverting Q 3 7 Output 6 OPA129 VOUT 5 In Low frequency cutoff = V- 1/(2R C ) = 0.16Hz F F 2 6 Out 3 VOUT = -Q/CF 8 FIGURE 6. Piezoelectric Transducer Charge Amplifier. Guard top and bottom of board. ~1pF to prevent gain peaking FIGURE 2. Connection of Input Guard. 1 8 V+ V0 1010 Connect to proper circuit node, depending on circuit configuration (see Figure 2). 4 5 2 (A) DIP package 1 8 V0 5 3 Connect to proper circuit node, depending on circuit configuration (see Figure 2). 0.1F V- FIGURE 3. Suggested Board Layout for Input Guard. OPA129 6 5 0.1F Output 5 x 109V/W -15V (B) SOIC package Circuit must be well shielded. FIGURE 7. Sensitive Photodiode Amplifier. OPA129 SBOS026A 8 7 V+ 4 +15V Guard Pin photodiode HP 5082-4204 V- www.ti.com 7 PACKAGE OPTION ADDENDUM www.ti.com 24-Feb-2009 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty Lead/Ball Finish MSL Peak Temp (3) OPA129P OBSOLETE PDIP P 8 TBD Call TI Call TI OPA129PB OBSOLETE PDIP P 8 TBD Call TI Call TI OPA129U ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR OPA129UB ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR OPA129UB/2K5 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR OPA129UB/2K5E4 ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR OPA129UBE4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR OPA129UBG4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR OPA129UE4 ACTIVE SOIC D 8 75 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 TAPE AND REEL INFORMATION *All dimensions are nominal Device OPA129UB/2K5 Package Package Pins Type Drawing SOIC D 8 SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) 2500 330.0 12.4 Pack Materials-Page 1 6.4 B0 (mm) K0 (mm) P1 (mm) 5.2 2.1 8.0 W Pin1 (mm) Quadrant 12.0 Q1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Jul-2012 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) OPA129UB/2K5 SOIC D 8 2500 367.0 367.0 35.0 Pack Materials-Page 2 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as "components") are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI's terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers' products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers' products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI's goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or "enhanced plastic" are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such components to meet such requirements. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP(R) Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright (c) 2012, Texas Instruments Incorporated