SCALETM-2 2SD300C17A1, 2SD300C17A1C 2SD300C17A1 and 2SD300C17A1C Preliminary Datasheet Dual-Channel High-quality and SCALETM-2 Driver Core Abstract The SCALETM-2 dual-driver core 2SD300C17A1 / 2SD300C17A1C (Coated version using ELPEGUARD SL 1307 FLZ/2 from Lackwerke Peters) is designed for applications in which high reliability is expected. The use of Power Integrations' highly integrated SCALE-2 chipset allows 63% of the components to be dispensed with compared to conventional drivers. This advantage is impressively reflected in increased reliability (function and MTBF). The 2SD300C17A1(C) combines a complete two-channel driver core with all components required for driving, such as an isolated DC/DC converter, short-circuit protection, failure soft shut down, short pulse suppression as well as supply voltage monitoring. Each of the two output channels is electrically isolated from the primary side and the other secondary channel. The driver provides a gate voltage swing of 15V. An output current of 30A and 4W drive power is available per channel. Its outstanding EMC with a dv/dt strength of more than 50V/ns allows safe and reliable operation in even the demanding industrial applications Product Highlights Dual channel driver Highly integrated SCALE-2 chipset Switching frequency up to 60kHz Gate current 30A 4W output power per channel Direct and half-bridge mode IGBT short-circuit protection Failure soft shut down Isolated DC/DC converter Safe isolation to EN 50178 UL compliant Reliable, long service life www.power.com/igbt-driver Applications IGBTs up to 1700V Page 1 SCALETM-2 2SD300C17A1, 2SD300C17A1C Preliminary Data Sheet Safety Notice! The data contained in this data sheet is intended exclusively for technically trained staff. Handling all highvoltage equipment involves risk to life. Strict compliance with the respective safety regulations is mandatory! Any handling of electronic devices is subject to the general specifications for protecting electrostatic-sensitive devices according to international standard IEC 60747-1, Chapter IX or European standard EN 100015 (i.e. the workplace, tools, etc. must comply with these standards). Otherwise, this product may be damaged. Important Product Documentation This data sheet contains only product-specific data. For a detailed description, must-read application notes and important information that apply to this product, please refer to "2SD300C17 Description & Application Manual" on www.power.com/igbt-driver/go/2SD300C17. Absolute Maximum Ratings Parameter Remarks Supply voltage VDC VDC to GND Supply voltage VDD Logic input voltages Logic output voltages SOx current Gate peak current Iout Gate resistance IGBT gate charge Average supply current IDC Output power VDD to GND INA, INB and Mod to GND SOA and SOB to GND Failure condition, total current Note 1 Turn-on and turn-off Notes 2, 3 Ambient temperature 70C (Notes 4, 5) Ambient temperature 85C (Note 4) Min Max Unit 0 16 V 0 16 V -0.5 20 V -0.5 VDD+0.5 V 20 mA -30 +30 A 1 50 C 540 mA 4 W 3 W 60 kHz 5000 VAC(eff) Switching frequency f Test voltage (50Hz/1min.) Primary to secondary (Note 11) |dV/dt| Operating voltage Secondary to secondary (Note 11) Rate of change of input to output voltage Primary and secondary to secondary side Operating temperature Note 5 -40 85 C Storage temperature Note 14 -40 50 C Surface temperature Only for 2SD300C17A1C (Note 15) 125 C www.power.com/igbt-driver 4000 VAC(eff) 50 kV/s 1700 Vpeak Page 2 SCALETM-2 2SD300C17A1, 2SD300C17A1C Preliminary Data Sheet Recommended Operating Conditions Power Supply Remarks Min Typ Max Unit Supply voltage VDC VDC to GND 14 15 16 V Supply voltage VDD VDD to GND 14 15 16 V Input logic level INx and Mod to GND, high level VDD V Input logic level INx and Mod to GND, low level 0 V Electrical Characteristics All data refer to +25C and VDC = VDD = 15V unless otherwise specified. Power supply Remarks Min Typ Max Unit Supply current IDC Without load 65 mA Supply current IDD Direct mode, f = 0Hz 14 mA Supply current IDD Direct mode, f = 60kHz 21 mA Coupling capacitance Cio Primary to secondary, per channel 22 pF Secondary to secondary 15 pF Power Supply Monitoring Remarks Min Typ Max Unit Supply threshold VDD Primary side, clear fault 11.9 12.6 13.3 V Primary side, set fault (Note 6) 11.3 12.0 12.7 V 0.35 12.1 11.5 0.35 5 4.7 0.15 12.6 12.0 13.1 12.5 5.15 4.85 5.3 5 Monitoring hysteresis Primary side, set/clear fault Secondary side, clear fault Secondary side, set fault (Note 7) Secondary side, set/clear fault Secondary side, clear fault Secondary side, set fault (Note 7) Secondary side, set/clear fault Logic Inputs and Outputs Remarks Min Typ Max Unit Input impedance Turn-on threshold Turn-off threshold SOx output voltage INx and Mod V(INx) V(INx) Failure condition, I(SOx) < 20mA 0.7 k V V V Short-Circuit Protection Remarks Max Unit Rth value Between RCx and COM x 70 k Blocking time Note 10 Monitoring hysteresis Supply threshold Vx+-VCOMx Monitoring hysteresis Supply threshold VCOMx-Vx- www.power.com/igbt-driver 3.9 8.1 4.8 Min Typ 2 27 V V V V V V V ms Page 3 SCALETM-2 2SD300C17A1, 2SD300C17A1C Preliminary Data Sheet External Fault input Remarks Threshold level Between E.x and COM x Timing Characteristics Remarks Turn-on delay td(on) Direct mode (Note 8) 630 ns Turn-off delay td(off) Short pulse suppression Dead time between channels Transmission delay of fault state Direct mode (Note 8) Turn-on command pulse width Turn-off command pulse width Half-bridge mode, with CA = CB = 0pF (Note 13) Note 9 490 470 300 1.3 450 ns ns ns s ns Output Voltage Remarks Typ Turn-on voltage Gate x to COM x 15 V Turn-off voltage Gate x to COM x -15 V Electrical Isolation Remarks Min Typ Max Unit Test voltage (50Hz/1s) Primary to secondary side (Note 11) 5000 5050 5100 Veff Secondary to secondary side (Note 11) 4000 4050 4100 Veff Primary to secondary side (Note 12) 1768 Vpeak Secondary to secondary side (Note 12) 1700 Vpeak Primary to secondary side 16.2 mm Secondary to secondary side 14.2 mm Primary to secondary side 16.2 mm Secondary to secondary side 6.5 mm Output Remarks Min Blocking capacitance Vx+ to COM x 9.4 F COM x to Vx- 9.4 F Partial discharge extinction volt. Creepage distance Clearance distance Min Typ Max 5 Min Min Typ Typ Unit V Max Max Max Unit Unit Unit Footnotes to the Key Data 1) 2) 3) 4) 5) The maximum peak gate current refers to the highest current level occurring during the product lifetime. It is an absolute value and does also apply for short pulses. The average supply input current is limited for thermal reasons. Higher values than specified by the absolute maximum rating are permissible (e.g. during power supply start up) if the average remains below the given value, provided the average is taken over a time period which is shorter than the thermal time constants of the driver in the application. There is no means of actively controlling or limiting the input current in the driver. In the case of start-up with very high blocking capacitor values, or in case of short circuit at the output, the supply input current has to be limited externally. The maximum output power must not be exceeded at any time during operation. The absolute maximum rating must also be observed for time periods shorter than the thermal time constants of the driver in the application. An extended output power range is specified for maximum ambient temperatures of 70C. www.power.com/igbt-driver Page 4 SCALETM-2 2SD300C17A1, 2SD300C17A1C Preliminary Data Sheet 6) 7) 8) 9) 10) 11) 12) 13) 14) 15) Undervoltage monitoring of the primary-side supply voltage (VDD to GND). If the voltage drops below this limit, a fault is transmitted to both outputs SOA and SOB and the IGBTs are switched off. Undervoltage monitoring of the secondary-side supply voltage (Vx+ to COM x and COM x to Vx- which correspond with the approximate turn-on and turn-off gate-emitter voltages). If the corresponding voltage drops below this limit, the IGBT is switched off and a fault is transmitted to the corresponding SOx output on the primary side. The delay time is measured between 50% of the input signal and 10% (turn-on) or 90% (turn-off) of the corresponding output. Transmission delay of fault state from the secondary side to the primary status output. The blocking time sets a minimum time span between the end of any fault state and the start of normal operation (remove fault from pin SOx). The value of the blocking time is programmed on the driver and cannot be modified externally. HiPot testing (= dielectric testing) must generally be restricted to suitable components. This gate driver is suited for HiPot testing. Nevertheless, it is strongly recommended to limit the testing time to 1s slots as stipulated by EN 50178. Excessive HiPot testing at voltages much higher than 1200V AC(eff) may lead to insulation degradation. No degradation has been observed over 1min. testing at 5000VAC(eff). The transformer of every production sample shipped to customers has undergone 100% testing at the given value for 1s. Partial discharge measurement is performed in accordance with IEC 60270 and isolation coordination specified in EN 50178. The partial discharge extinction voltage between primary and either secondary side is coordinated for safe isolation to EN 50178. The dead time is measured between 50% voltage swing of the gate-emitter voltage which is turned off and 50% voltage swing of the gate-emitter voltage which is turned-on. The storage temperature inside the original package (1) or in case the coating material of coated products may touch external parts (2) must be limited to the given value. Otherwise, it is limited to 90C. The component surface temperature, which may strongly vary depending on the operating condition, must be limited to the given value for coated driver versions to ensure long-term reliability of the coating material. Legal Disclaimer The statements, technical information and recommendations contained herein are believed to be accurate as of the date hereof. All parameters, numbers, values and other technical data included in the technical information were calculated and determined to our best knowledge in accordance with the relevant technical norms (if any). They may base on assumptions or operational conditions that do not necessarily apply in general. We exclude any representation or warranty, express or implied, in relation to the accuracy or completeness of the statements, technical information and recommendations contained herein. No responsibility is accepted for the accuracy or sufficiency of any of the statements, technical information, recommendations or opinions communicated and any liability for any direct, indirect or consequential loss or damage suffered by any person arising therefrom is expressly disclaimed. www.power.com/igbt-driver Page 5 SCALETM-2 2SD300C17A1, 2SD300C17A1C Preliminary Data Sheet Ordering Information Our international terms and conditions of sale apply. Type Designation Description 2SD300C17A1 2SD300C17A1C Dual-channel SCALE-2 driver core (PCB thickness: 1.55mm) Dual-channel SCALE-2 driver core (PCB thickness: 1.55mm, conformal coating) Product home page: www.power.com/igbt-driver/go/2SD300C17 Refer to www.power.com/igbt-driver/go/nomenclature for information on driver nomenclature Information about Other Products For other drivers, product documentation, and application support Please click: www.power.com (c) 2009...2018 Power Integrations Switzerland GmbH. We reserve the right to make any technical modifications without prior notice. www.power.com/igbt-driver All rights reserved. Version 3.0 from 2018-02-09 Page 6 SCALETM-2 2SD300C17A1, 2SD300C17A1C Preliminary Data Sheet Power Integrations Sales Offices WORLD HEADQUARTERS 5245 Hellyer Avenue San Jose, CA 95138 USA Tel: +1-408-414-9200 Fax: +1-408-414-9765 Email: usasales@power.com AMERICAS EAST 7360 McGinnis Ferry Road Suite 225 Suwannee, GA 30024 USA Tel: +1-678-957-0724 Fax: +1-678-957-0784 Email: usasales@power.com AMERICAS CENTRAL 333 Sheridan Road Winnetka, IL 60093 USA Tel: +1-847-721-6293 Email: usasales@power.com AMERICAS WEST 5245 Hellyer Avenue San Jose, CA 95138 USA Tel: +1-408-414-8778 Fax: +1-408-414-3760 Email: usasales@power.com CHINA (Shanghai) Room 2410, Charity Plaza No. 88 North Caoxi Road Shanghai, 200030 China Tel: +86-21-6354-6323 Fax: +86-21-6354-6325 Email: chinasales@power.com CHINA (Shenzhen) 17/F, Hivac Building, No 2 Keji South 8th Road, Nanshan District Shenzhen, 518057 China Tel: +86-755-8672-8689 Fax: +86-755-8672-8690 Email: chinasales@power.com GERMANY (AC-DC/LED Sales) Lindwurmstrasse 114 80337 Munchen, Germany Tel: +49-89-5527-39100 Fax: +49-89-1228-5374 Email: eurosales@power.com GERMANY (Gate Driver Sales) HellwegForum 1 59469 Ense, Germany Tel: +49-2938-64-39990 Email: igbt-driver.sales@power.com INDIA (Bangalore) #1, 14th Main Road Vasanthangar Bangalore, 560052 India Tel 1: +91-80-4113-8020 Tel 2: +91-80-4113-8028 Fax: +91-80-4113-8023 Email: indiasales@power.com INDIA (Mumbai) Unit: 106-107, Sagar Tech Plaza-B Sakinaka, Andheri Kurla Road Mumbai, Maharashtra 400072 India Tel 1: +91-22-4003-3700 Tel 2: +91-22-4003-3600 Email: indiasales@power.com INDIA (New Dehli) #45, Top Floor Okhla Industrial Area, Phase - III New Dehli, 110020 India Tel 1: +91-11-4055-2351 Tel 2: +91-11-4055-2353 Email: indiasales@power.com ITALY Via Milanese 20 20099 Sesto San Giovanni (MI), Italy Tel: +39-02-4550-8708 Email: eurosales@power.com JAPAN Kosei Dai-3 Bldg. 2-12-11, Shin-Yokohama, Kohoku-ku Yokohama-shi, Kanagawa Japan 222-0033 Tel: +81-45-471-1021 Fax: +81-45-471-3717 Email: japansales@power.com KOREA RM602, 6FL, 22 Teheran-ro 87-gil, Gangnam-gu Seoul, 06164 Korea Tel: +82-2-2016-6610 Fax: +82-2-2016-6630 Email: koreasales@power.com SINGAPORE 51 Newton Road #19-01/05 Goldhill Plaza Singapore, 308900 Tel 1: +65-6358-2160 Tel 2: +65-6358-4480 Fax: +65-6358-2015 Email: singaporesales@power.com TAIWAN 5F, No. 318, Nei Hu Rd., Sec. 1 Nei Hu Dist. Taipei, 114 Taiwan Tel: +886-2-2659-4570 Fax: +886-2-2659-4550 Email: taiwansales@power.com UNITED KINGDOM Bulding 5, Suite 21 The Westbrook Centre Milton Road Cambridge, CB4 1YG United Kingdom Tel: +44-7823-557-484 Email: eurosales@power.com www.power.com/igbt-driver Page 7